FCC ID: K7SF6D4230V3 Enhanced Wireless Router

Enhanced Wireless Router User Manual 8820-00034-A F6D4230-4 TablE of ConTEnTs table of c ontents sections 1 2 3 4 5 6 7 8 9 10 1 Introduction 1 Advantages of a Wireless Network 1 Placement of your Enhanced Wireless Router 2 2 Product overview 5 Product Features 5 3 Knowing your Router 7 Package Contents 7 System Requirements 7 Setup Assistant Software System Requirements 7 Setting WEP Encryption 47 Using the Access Point Mode 49 Setting MAC Address Control 50 Configuring the Firewall 52 Using Dynamic DNS 56 Utilities 57 Restarting the Router 58 Updating the Firmware 64 7 Manually Configuring network settings 71 8 Recommended Web browser settings 76 4 Connecting and Configuring your Router 11 9 Troubleshooting 78 5 alternate setup Method 21 10 Information 93 6 Using the Web-based advanced User Interface 36 Changing LAN Settings 37 Viewing the DHCP Client List Page 39 Configuring the Wireless Network Settings 40 Setting WPA/WPA2 Encryption 46 Enhanced Wireless Router i InTRodUCTIon table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Thank you for purchasing the Belkin Enhanced Wireless Router (the Router) Following are two short sectionsthe first discusses the benefits of home networking, and the other outlines best practices that maximize your wireless home network range and performance Please be sure to read through this User Manual completely, and pay special attention to the section entitled Placement of your Enhanced Wireless Router on the next page By following our simple setup instructions you will be able to use your Belkin Home Network to:

Share one high-speed Internet connection with all the computers in your home Share resources, such as files and hard drives among all the connected computers in your home advantages of a Wireless network Here are some of the advantages of setting up a Belkin Wireless Network:

Mobility youll no longer need a dedicated computer room now you can work on a networked laptop or desktop computer anywhere within your wireless range Easy installation Belkins Setup Assistant makes setup simple Flexibility set up and access printers, computers, and other networking devices from anywhere in your home Enhanced Wireless Router 1 Share a single printer with the entire family Share documents, music, video, and digital pictures Store, retrieve, and copy files from one computer to another Simultaneously play games online, check Internet email, and chat Easy expansion the wide range of Belkin networking products let you expand your network to include devices such as printers and gaming consoles No cabling required you can spare the expense and hassle of retrofitting Ethernet cabling throughout the home or office Widespread industry acceptance choose from a wide range of interoperable networking products InTRodUCTIon table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Placement of your Enhanced Wireless Router Important factors for Placement and setup Your wireless connection will be stronger the closer your computer is to your Router Typical indoor operating range for wireless devices is between 100 and 200 feet In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router and connected devices increases This may or may not be noticeable to you As you move further from your Router, connection speed may decrease Factors that can weaken signals simply by getting in the way of your networks radio waves are metal appliances or obstructions, and walls If you have concerns about your networks performance that might be related to range or obstruction factors, try moving the computer to a position between five and 10 feet from the Router in order to see if distance is the problem If difficulties persist even at close range, please contact Belkin Technical Support note: While some of the items listed below can affect network performance, they will not prohibit your wireless network from functioning; if you are concerned that your network is not operating at its maximum effectiveness, this checklist may help 1 Router Placement Place your Router, the central connection point of your network, as close as possible to the center of your wireless network devices To achieve the best wireless network coverage for your wireless clients

(ie, computers enabled by Belkin Wireless Notebook Network Cards, Wireless Desktop Network Cards, and Wireless USB Adapters):

Enhanced Wireless Router 2 Ensure that your Routers networking antenna is positioned vertically (toward the ceiling) In multistory homes, place the Router on a floor that is as close to the center of the home as possible This may mean placing the Router on an upper floor Try not to place the Router near a cordless 24GHz phone Refrigerators 2 avoid obstacles and Interference Avoid placing your Router near devices that may emit radio noise, such as microwave ovens Dense objects that can inhibit wireless communication include:

Washers and/or dryers Metal cabinets Metallic-based UV tinted windows If your wireless signal seems weak in some spots, make sure that objects such as these are not blocking the signals path (between your computers and Router) Large aquariums InTRodUCTIon table of c ontents sections 1 2 3 4 5 6 7 8 9 10 3 Cordless Phones If the performance of your wireless network is impaired after attending to the above issues, and you have a cordless phone:

Try moving cordless phones away from your Router and your wireless-enabled computers Unplug and remove the battery from any cordless phone that operates on the 24GHz band (check manufacturers information) If this fixes the problem, your phone may be interfering If your phone supports channel selection, change the channel on the phone to the farthest channel from your wireless network For example, change the phone to channel 1 and move your Router to channel 11 See your phones user manual for detailed instructions If necessary, consider switching to a 900MHz or 5GHz cordless phone 4 Choose the Quietest Channel for your Wireless network In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless networks nearby that can conflict with yours Use the Site Survey capabilities found in the Wireless Utility of your wireless adapter to locate any other wireless networks that are available

(see your wireless adapters user manual), and move your Router and computers to a channel as far away from other networks as possible Experiment with more than one of the available channels, in order to find the clearest connection and avoid interference from neighboring cordless phones or other wireless devices For Belkin wireless networking products, use the detailed Site Survey and wireless channel information included with your wireless network card See your network cards user guide for more information These guidelines should allow you to cover the maximum possible area with your Router Should you need to cover an even wider area, we suggest the Belkin Wireless Range Extender/Access Point Enhanced Wireless Router 3 InTRodUCTIon table of c ontents sections 1 2 3 4 5 6 7 8 9 10 5 secure Connections, VPns, and aol Secure connections typically require a user name and password, and are used where security is important Secure connections include:

Virtual Private Network (VPN) connections, often used to connect remotely to an office network The Bring Your Own Access program from America Online (AOL), which lets you use AOL through broadband provided by another cable or DSL service Most online banking websites Many commercial websites that require a user name and password to access your account Secure connections can be interrupted by a computers power management setting, which causes it to go to sleep The simplest solution to avoid this is to simply reconnect by rerunning the VPN or AOL software, or by re-logging into the secure website A second alternative is to change your computers power management settings so it does not go to sleep; however, this may not be appropriate for portable computers To change your power management setting under Windows, see the Power Options item in the Control Panel If you continue to have difficulty with Secure Connections, VPNs, and AOL, please review the steps above to be sure you have addressed these issues For more information regarding our networking products, visit our website at wwwbelkincom/networking or call Belkin Technical Support at:

US: 877-736-5771 UK: 0845 607 77 87 Australia: 1800 235 546 New Zealand: 0800 235 546 Singapore: 65 64857620 Europe: wwwbelkincom/support Enhanced Wireless Router 4 PRodUCT oVERVIEW table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Product features In minutes you will be able to share your Internet connection and network your computers The following is a list of features that make your new Belkin Enhanced Wireless Router an ideal solution for your home or small office network Works with both PCs and Mac Computers The Router supports a variety of networking environments including Mac OS 8x, 9x, X v10x, Linux, Windows 98, Me, NT, 2000, XP, Vista, and others All that is needed is an Internet browser and a network adapter that supports TCP/IP (the standard language of the Internet) naT IP address sharing Your Router employs Network Address Translation (NAT) to share the single IP address assigned to you by your Internet Service Provider while saving the cost of adding additional IP addresses to your Internet service account Patent-Pending network status display Lighted LEDs on the front of the Router indicate which functions are in operation Youll know at-a-glance whether your Router is connected to the Internet This feature eliminates the need for advanced software and status-monitoring procedures sPI firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including IP Spoofing, Land Attack, Ping of Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIP defect, and fragment flooding Web-based advanced User Interface You can set up the Routers advanced functions easily through your web browser, without having to install additional software onto the computer There are no disks to install or keep track of and, best of all, you can make changes and perform setup functions from any computer on the network quickly and easily Integrated 10/100 4-Port switch The Router has a built-in, four-port network switch to allow your wired computers to share printers, data and MP3 files, digital photos, and much more The switch features automatic detection so it will adjust to the speed of connected devices The switch will transfer data between computers and the Internet simultaneously without interrupting or consuming resources Enhanced Wireless Router 5 PRodUCT oVERVIEW table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Integrated Enhanced Wireless access Point Enhanced is an exciting new wireless technology that achieves data rates of up to 150Mbps Actual throughput is typically lower than the connected data rate and will vary depending on your networking environment noTE: The standard transmission rate150Mbpsis the physical data rate Actual data throughput will be lower MaC address filtering For added security, you can set up a list of MAC addresses (unique client identifiers) that are allowed access to your network Every computer has its own MAC address Simply enter these MAC addresses into a list using the Web-Based Advanced User Interface and you can control access to your network Universal Plug and Play (UPnP) UPnP is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant support for VPn Pass-Through If you connect to your office network from home using a VPN connection, your Router will allow your VPN-equipped computer to pass through the Router and to your office network built-In dynamic Host Configuration Protocol (dHCP) Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for the easiest possible connection of a network The DHCP server will assign IP addresses to each computer automatically so there is no need for a complicated networking setup setup assistant The Setup Assistant, second generation of Belkins renowned Easy Install Wizard, takes the guesswork out of setting up your Router This automatic software determines your network settings for you and sets up the Router for connection to your Internet Service Provider (ISP) In a matter of minutes, your Router will be up and running on the Internet noTE: Setup Assistant software is compatible with Windows 2000, XP, and Vista; and Mac OS X v10x If you are using another operating system, the Router can be set up using the Alternate Setup Method described in this User Manual (see page 21) Enhanced Wireless Router 6 KNOWING YOUR ROUTER Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10 Package Contents

Belkin Enhanced Wireless Router Quick Installation Guide Belkin Setup Assistant Software CD RJ45 Ethernet Networking Cable Power Supply User Manual on the Setup Assistant CD System Requirements The Router has been designed to be placed on a desktop. All of the cables exit from the rear of the Router for better organization and utility. The Network Status Display is easily visible on the FRONT of the Router to provide you with information about network activity and status.

Broadband Internet connection such as a cable or DSL modem with RJ45 (Ethernet) connection At least one computer with an installed network interface adapter TCP/IP networking protocol installed on each computer RJ45 Ethernet networking cable Internet browser Setup Assistant Software System Requirements

A computer running Windows 2000, XP, or Vista; or Mac OS X v10.x

Minimum 1GHz processor and 128MB RAM

Internet browser

(A)

(B)

(C)

(D)

(E)

(F)

(G) Enhanced Wireless Router 7 KNOWING YOUR ROUTER Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10 A. Wireless Security D. Wired-Computer Status Solid Green Blinking Amber Wired computer is not present Wired computer is connected to the Router Problem with wired computer connecting properly to the Router E. Router/Power Status When you apply power to the Router or restart it, a short period of time elapses while the Router boots up. During this time, the router icon blinks. When the Router has completely booted up, the router icon becomes a solid light, indicating the Router is ready for use. Off Blinking Green Solid Green Router is off Router is booting up Router is on and ready OFF Solid Green Wireless security is off Off Wireless security is on B. Wi-Fi Protected Setup (WPS) button This button is used for the Wi-Fi Protected Setup feature. Please refer to the Changing the Wireless Security Settings section. WPS C. Wireless-Computer Status Off Solid Green Blinking Amber Wireless computer is not present Wireless computer is connected to the Router Problem with wireless computer connecting properly to the Router Enhanced Wireless Router 8 KNOWING YOUR ROUTER Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10 F. Modem Status This icon lights in green to indicate that your modem is connected properly to the Router. It turns amber when problem is detected. OFF Solid Green Router is NOT connected to modem Router is connected to modem and functioning properly Blinking Amber Problem with modem G. Internet Status This unique icon shows you when the Router is connected to the Internet. When the light is off, the Router is NOT connected to the Internet. When the light is blinking amber, the Router is attempting to connect to the Internet. When the light is solid blue, the Router is connected to the Internet. When using the Disconnect after x minutes feature, this icon becomes extremely useful in monitoring the status of your Routers connection. Off Blinking Amber Solid Green Router is NOT connected to the Internet Router is attempting to connect to the Internet Router is connected to the Internet Enhanced Wireless Router 9

(H)

(I)

(K)

(J) KnoWIng yoUR RoUTER table of c ontents sections 1 2 3 4 5 6 7 8 9 10 H Connections to Wired Computers gray Connect your wired (non-wireless) computers to these ports These ports are RJ45, 10/100 auto-negotiation, auto-uplinking ports for standard UTP category 5 or 6 Ethernet cable The ports are labeled 1 through 4 I Connection to Modem yellow This port is for connection to your cable or DSL modem Use the cable that was provided with the router to connect the modem to this port Use of a cable other than the one supplied with the router may not work properly J Reset button Red The Reset button is used in rare cases when the Router may function improperly Resetting the Router will restore the Routers normal operation while maintaining the programmed settings You can also restore the factory default settings by using the Reset button Use the restore option in instances where you may have forgotten your custom password i Resetting the Router Push and release the Reset button The lights on the Router will momentarily flash The router light will begin to blink When the router light becomes solid again, the reset is complete ii Restoring the factory defaults Press and hold the reset button for at least 10 seconds, then release it The lights on the Router will momentarily flash The router light will begin to blink When the router light becomes solid again, the restore is complete K Power Jack black Connect the included 12V/1A DC power supply to this jack Enhanced Wireless Router 10 ConnECTIng and ConfIgURIng yoUR RoUTER table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setup assistant Belkin has provided our Setup Assistant software to make installing your Router a simple and easy task You can use it to get your Router up and running in minutes The Setup Assistant requires that your computer be connected directly to your Router and that the Internet connection is active and working at the time of installation If it is not, you must use the Alternate Setup Method section of this User Manual to configure your Router Additionally, if you are using an operating system other than Windows 2000, XP, or Vista, or Mac OS X v10x, you must set up the Router using the Alternate Setup Method section of this User Manual Verify the contents of your box you should have the following:

Belkin Enhanced Wireless Router RJ45 Ethernet Networking Cable Power Supply Belkin Setup Assistant Software CD User Manual on the Setup Assistant CD Modem Requirements Your cable or DSL modem must be equipped with an RJ45 Ethernet port Many modems have both an RJ45 Ethernet port and a USB connection If you have a modem with both Ethernet and USB, and are using the USB connection at this time, you will be instructed to use the RJ45 Ethernet port during the installation procedure If your modem has only a USB port, you can request a different type of modem from your ISP, or you can, in some cases, purchase a modem that has an RJ45 Ethernet port on it Ethernet Usb Enhanced Wireless Router 11 CONNECTING AND CONFIGURING YOUR ROUTER Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10

[1] Make sure your DSL or cable line is plugged into your modem. Put the Router next to your DSL or cable modem. WAN LAN

[2] Remove the power cord from your DSL or cable modem. Connect the modem to the Routers modem port with an Ethernet cable. (Your computer might be plugged into the modem already.) Connect your computer to the Router with another Ethernet cable (temporarily, if need be). Enhanced Wireless Router 12 CONNECTING AND CONFIGURING YOUR ROUTER Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10 WAN LAN

[3] Plug in your modem and make sure it turns on. If your modem is already on, unplug it, wait a few seconds, and plug it back in. Plug the Routers power supply into the Router and a power outlet. Put the CD into your computer. If the Setup Assistant doesnt run automatically, browse the CD, find the Setup Assistant icon, and run it. IMPORTANT: Run the Setup Assistant from the computer that is directly connected to the Router from Step 2. Enhanced Wireless Router 13 ConnECTIng and ConfIgURIng yoUR RoUTER table of c ontents sections 1 2 3 4 5 6 7 8 9 10 note for Windows Users: If the Setup Assistant does not start up automatically, select your CD-ROM drive from My Computer and double-click on the file named SetupAssistant to start the Setup Assistant Enhanced Wireless Router 14 ConnECTIng and ConfIgURIng yoUR RoUTER table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Confirmation screen Verify that you have completed all QIG steps by checking the box to the right of the arrow Click Next to continue Progress screen Setup Assistant will show you a progress screen each time a step in the setup has been completed Enhanced Wireless Router 15 ConnECTIng and ConfIgURIng yoUR RoUTER table of c ontents sections 1 2 3 4 5 6 7 8 9 10 11 Checking settings The Setup Assistant will now examine your computers network settings and gather information needed to complete the Routers connection to the Internet 12 Verifying Hardware Connections The Setup Assistant will now verify your hardware connection Enhanced Wireless Router 16 ConnECTIng and ConfIgURIng yoUR RoUTER table of c ontents sections 1 2 3 4 5 6 7 8 9 10 13 naming your Wireless network The Setup Assistant will display the default wireless network name or Service Set Identifier (SSID) This is the name of your wireless network to which your computers or devices with wireless network adapters will connect You can either use the default or change it to something unique Write down this name for future reference Click Next to continue 14 Requesting Internet account Info (if needed) If your Internet account requires a login and password, you will be prompted with a screen similar to the illustration below Select your country or ISP from the drop-down boxes Enhanced Wireless Router 17 ConnECTIng and ConfIgURIng yoUR RoUTER table of c ontents sections 1 2 3 4 5 6 7 8 9 10 15 Configuring the Router The Setup Assistant will now configure your Router by sending data to the Router and restarting it Wait for the on-screen instructions note: Do not disconnect any cable or power off the Router while the Router is rebooting Doing so will render your Router inoperable 16 Checking Internet Connection We are almost done The Setup Assistant will now check your connection to the Internet Enhanced Wireless Router 18 ConnECTIng and ConfIgURIng yoUR RoUTER table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Congratulations You have finished installing your new Belkin Router You will see the Congratulations screen when your Router can connect to the Internet You can begin surfing by opening your browser and going to any website You can use the Setup Assistant to set up your other wired and wireless computers to connect to the Internet by clicking Next If you decide to add computers to your Router later, select Exit the Assistant and then click Next Troubleshooting If the Setup Assistant is not able to connect to the Internet, you will see the following screen Follow the on-screen instructions to go through the troubleshooting steps Enhanced Wireless Router 19 ConnECTIng and ConfIgURIng yoUR RoUTER table of c ontents sections 1 2 3 4 5 6 7 8 9 10 17 optional: assistance Connecting other Computers This optional step will help you to connect additional wired and wireless computers to your network Follow the on-screen instructions Congratulations Once you have verified that your other wired and wireless computers are properly connected, your network is set up and working You can now surf the Internet Click Next to take you back to the main menu Enhanced Wireless Router 20 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 step 1: Hardware Connections follow the Quick Installation guide See the QIG or Step 1: Hardware Connections from the previous section step 2: set your Computers network settings to Work with a dHCP server See the section in this User Manual called Manually Configuring Network Settings for directions step 3 Configure the Router Using the Web-based advanced User Interface Using your Internet browser, you can access the Routers Web-Based Advanced User Interface In your browser, type 19216821 (you do not need to type in anything else such as http:// or www) Then press the Enter key Enhanced Wireless Router 21 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 logging into the Router You will see the Routers home page in your browser window The home page is visible to any user who wants to see it To make any changes to the Routers settings, you have to log in Clicking the Login button or clicking on any one of the links on the home page will take you to the login screen The Router ships with no password entered In the login screen, leave the password blank and click the Submit button to log in logging out of the Router One computer at a time can log into the Router for the purposes of making changes to the settings of the Router Once a user has logged in to make changes, there are two ways that the computer can be logged out Clicking the Logout button will log the computer out The second method is automatic The login will time out after a specified period of time The default login time-out is 10 minutes This can be changed from one to 99 minutes For more information, see the section in this manual titled Changing the Login Time-Out Setting Enhanced Wireless Router 22 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Understanding the Web-based advanced User Interface The home page is the first page you will see when you access the Advanced User Interface (UI) The home page shows you a quick view of the Routers status and settings All advanced setup pages can be reached from this page

(11)

(1)

(7)

(2)

(5)

(4)

(3)

(6)

(8)

(9)

(10) Enhanced Wireless Router 23 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 1 Quick-navigation links You can go directly to any of the Routers advanced UI pages by clicking directly on these links The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find Clicking on the purple header of each tab will show you a short description of the tabs function 2 Home button The home button is available in every page of the UI Pressing this button will take you back to the home page 3 Help button The Help button gives you access to the Routers help pages Help is also available on many pages by clicking more info next to certain sections of each page 4 login/logout button This button enables you to log in and out of the Router with the press of one button When you are logged into the Router, this button will change to read Logout Logging into the Router will take you to a separate login page where you will need to enter a password When you are logged into the Router, you can make changes to the settings When you are finished making changes, you can log out of the Router by clicking the Logout button For more information about logging into the Router, see the section called Logging into the Router 5 Internet-status Indicator This indicator is visible in all pages of the Router, indicating the connection status of the Router When the indicator says Connected in blue, the Router is connected to the Internet When the Router is not connected to the Internet, the indicator will read Not Connected in RED The indicator is automatically updated when you make changes to the settings of the Router Enhanced Wireless Router 24 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 6 language Shows the active language for the Advanced User Interface Select a desirable language by clicking one of the available languages 7 Version Info Shows the firmware version, boot-code version, hardware version, and serial number of the Router 8 lan settings Shows you the settings of the Local Area Network (LAN) side of the Router Changes can be made to the settings by clicking on any one of the links (IP Address, Subnet Mask, DHCP Server) or by clicking the LAN quick-navigation link on the left side of the screen 9 Internet settings Shows the settings of the Internet/WAN side of the Router that connects to the Internet Changes to any of these settings can be made by clicking on the links or by clicking on the Internet/WAN quick-

navigation link on the left side of the screen 10 features Shows the status of the Routers, firewall, and wireless features Changes can be made to the settings by clicking on any one of the links or by clicking the quick-navigation links on the left side of the screen 11 Page name The page you are on can be identified by this name This User Manual will sometimes refer to pages by name For instance LAN > LAN Settings refers to the LAN Settings page Enhanced Wireless Router 25 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 step 4: Configuring your Router for Connection to your Internet service Provider (IsP) The Internet/WAN tab is where you will set up your Router to connect to your Internet Service Provider (ISP) The Router is capable of connecting to virtually any ISPs system provided you have correctly configured the Routers settings for your ISPs connection type Your ISP connection settings are provided to you by your ISP To configure the Router with the settings that your ISP gave you, click Connection Type

(a) on the left side of the screen Select the connection type you use If your ISP gave you DNS settings, clicking DNS (b) allows you to enter DNS address entries for ISPs that require specific settings Clicking MAC Address (C) will let you clone your computers MAC address or type in a specific WAN MAC address, if required by your ISP When you have finished making settings, the Internet Status indicator will read connected if your Router is set up properly setting your Connection Type From the Connection Type page, you can select the type of connection you use Select the type of connection you use by clicking the button (1) next to your connection type and then clicking Next (2)

(1)

(2)

(A)

(B)

(C) Enhanced Wireless Router 26 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting your Internet service Provider (IsP) Connection Type to dynamic IP A dynamic connection type is the most common connection type found with cable modems Setting the connection type to dynamic in many cases is enough to complete the connection to your ISP Some dynamic connection types may require a host name You can enter your host name in the space provided if you were assigned one Your host name is assigned by your ISP Some dynamic connections may require that you clone the MAC address of the PC that was originally connected to the modem

(1)

(3) 1 Host name (1) This space is provided to enter a host name that needs to be visible to your ISP Enter your host name here and click Apply Changes (3) If your ISP did not assign you a host name, or you are not sure, leave this blank 2 Change Wan MaC address (2) If your ISP requires a specific MAC address to connect to the service, you can enter a specific MAC address or clone the current computers MAC address through this link

(2) Enhanced Wireless Router 27 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting your Internet service Provider (IsP) Connection Type to static IP A static IP address connection type is less common than other connection types If your ISP uses static IP addressing, you will need your IP address, subnet mask, and ISP gateway address This information is available from your ISP or on the paperwork that your ISP left with you Type in your information, then click Apply Changes (4) After you apply the changes, the Internet Status indicator will read connected if your Router is set up properly IP address (1) 1 Provided by your ISP Enter your IP address here 2 subnet Mask (2) Provided by your ISP Enter your subnet mask here 3 Provided by your ISP Enter the ISP gateway address here IsP gateway address (3)

(1)

(2)

(3)

(4) Enhanced Wireless Router 28 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting your IsP Connection Type to PPPoE Most DSL providers use PPPoE as the connection type If you use a DSL modem to connect to the Internet, your ISP may use PPPoE to log you into the service If you have an Internet connection in your home or small office that doesnt require a modem, you may also use PPPoE Your connection type is PPPoE if:

Your ISP gave you a user name and password, which is required to connect to the Internet Your ISP gave you software such as WinPOET or Enternet300 that you use to connect to the Internet You have to double-click on a desktop icon other than your browser to get on the Internet

(1)

(2)

(3)

(4)

(5)

(6) Enhanced Wireless Router 29 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 1 User name This space is provided to type in your user name that was assigned by your ISP 2 Password Type in your password and retype it into the Retype Password box to confirm it service name 3 A service name is rarely required by an ISP If you are not sure if your ISP requires a service name, leave this blank IP assigned by IsP 4 If your ISP provided you with a specific IP address, select Yes and enter your IP address and subnet mask in the fields that appear 5 MTU The MTU setting should never be changed unless your ISP gives you a specific MTU setting Making changes to the MTU setting can cause problems with your Internet connection including disconnection from the Internet, slow Internet access, and problems with Internet applications working properly 6 disconnect after X The Disconnect feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time For instance, placing a check mark next to this option and entering 5 into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity This option should be used if you pay for your Internet service by the minute Enhanced Wireless Router 30 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting your Internet service Provider (IsP) Connection Type to Point-to-Point Tunneling Protocol (PPTP)

[European Countries Only]

Some ISPs require a connection using PPTP protocol, a type of connection most common in European countries This sets up a direct connection to the ISPs system Type in the information provided by your ISP in the space provided When you have finished, click Apply Changes (7) After you apply the changes, the Internet Status indicator will read Connected if your Router is set up properly

(1)

(2)

(3)

(4)

(5)

(6)

(7) 31 Enhanced Wireless Router alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 1 PPTP account Provided by your ISP Enter your PPTP User ID here 4 service IP address Provided by your ISP Enter your PPTP gateway/service IP address here 2 PPTP Password Type in your password and retype it into the Retype Password box to confirm it 5 IP assigned by IsP If your ISP provided you with a specific IP address, select Yes and enter your IP address and subnet mask in the fields that appear 3 Host name Provided by your ISP Enter your host name here 6 Connection Id (optional) Provided by your ISP Enter the connection ID here Enhanced Wireless Router 32 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting your Internet service Provider (IsP) Connection Type to layer 2 Tunneling Protocol (l2TP)

[Israel Only] Some ISPs require a connection using L2TP protocol, a type of connection most common in Israel This sets up a direct connection to the ISPs system Type in the information provided by your ISP in the space provided When you have finished, click Apply Changes (7) After you apply the changes, the Internet Status indicator will read Connection OK if your Router is set up properly 1 l2TP account Provided by your ISP Enter your L2TP User ID here 2 l2TP Password Type in your password and retype it into the Retype Password box to confirm it 6 disconnect after X minutes This feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time For instance, placing a check mark next to this option and entering 5 into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity This option should be used if you pay for your Internet service by the minute 3 Host name Provided by your ISP Enter your host name here 4 service IP address Provided by your ISP Enter your L2TP gateway/service IP address here 5 IP assigned by IsP If your ISP provided you with a specific IP address, select Yes and enter your IP address and subnet mask in the fields that appear Enhanced Wireless Router 33

(1)

(2)

(3)

(4)

(5)

(6)

(7) alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting your Connection Type if you are a Telstra bigPond/

optusnet Cable User [australia only]

Follow the on-screen steps and click Apply Changes to complete your setup setting Custom domain name server (dns) settings A Domain Name Server is a server located on the Internet that translates Universal Resource Locators (URLs) like wwwbelkincom into IP addresses Many Internet Service Providers (ISPs) do not require you to enter this information into the Router The Automatic from ISP

(1) box should be checked if your ISP did not give you a specific DNS address If you are using a static IP connection type, then you may need to enter a specific DNS address and secondary DNS address for your connection to work properly If your connection type is dynamic or PPPoE, it is likely that you do not have to enter a DNS address Leave the Automatic from ISP box checked To enter the DNS address settings, uncheck the Automatic from ISP box and enter your DNS entries in the spaces provided Click Apply Changes (2) to save the settings

(1)

(2) Enhanced Wireless Router 34 alTERnaTE sETUP METHod table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Configuring your Wan Media access Controller (MaC) address All network components including cards, adapters, and routers, have a unique serial number called a MAC address Your Internet Service Provider (ISP) may record the MAC address of your computers adapter and only let that particular computer connect to the Internet service When you install the Router, its own MAC address will be seen by the ISP and may cause the connection not to work Belkin has provided the ability to clone (copy) the MAC address of the computer into the Router This MAC address, in turn, will be seen by the ISPs system as the original MAC address and will allow the connection to work If you are not sure whether your ISP needs to see the original MAC address, simply clone the MAC address of the computer that was originally connected to the modem Cloning the address will not cause any problems with your network Cloning your MaC address To clone your MAC address, make sure that you are using the computer that was ORIGINALLY CONNECTED to your modem before the Router was installed Click the Clone button (1) Click Apply Changes (3) Your MAC address is now cloned to the Router Entering a specific MaC address In certain circumstances you may need a specific WAN MAC address You can manually enter one in the MAC Address page Type in a MAC address in the spaces provided (2) and click Apply Changes (3) to save the changes The Routers WAN MAC address will now be changed to the MAC address you specified

(2)

(1)

(3) Enhanced Wireless Router 35 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Using your Internet browser, you can access the Routers Web-Based Advanced User Interface In your browser, type 19216821 (do not type in anything else such as http:// or www) then press the Enter key Viewing the lan settings Clicking on the header of the LAN Setup tab (1) will take you its header page A quick description of the functions can be found here To view the settings or make changes to any of the LAN settings, click on LAN Settings (2), or to view the list of connected computers, click on DHCP Client List (3) You will see the Routers home page in your browser window

(1)

(2)

(3) Enhanced Wireless Router 36 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Changing lan settings All settings for the internal LAN setup of the Router can be viewed and changed here

(1)

(2)

(3)

(4)

(5)

(6) IP address 1 The IP address is the internal IP address of the Router The default IP address is 19216821 To access the advanced setup interface, type this IP address into the address bar of your browser This address can be changed if needed To change the IP address, type in the new IP address and click Apply Changes The IP address you choose should be a non-routable IP Examples of a non-routable IP are:

192168xx (where x is anything between 1 and 254) 10xxx (where x is anything between 1 and 254) 172yxx (where x is anything between 1 and 254 and y is anything between 16 and 31) 2 subnet Mask There is no need to change the subnet mask This is a unique, advanced feature of your Belkin Router It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so The default setting is 2552552550 Enhanced Wireless Router 37 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 3 dHCP server The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically The default setting is On The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network To turn off the DHCP server, select Off and click Apply Changes IP Pool 4 The range of IP addresses set aside for dynamic assignment to the computers on your network The default is 2100 (99 computers) If you want to change this number, you can do so by entering a new starting and ending IP address and clicking on Apply Changes The DHCP server can assign 100 IP addresses automatically This means that you cannot specify an IP address pool larger than 100 computers For example, starting at 50 means you have to end at 150 or lower so as not to exceed the 100-client limit The starting IP address must be lower in number than the ending IP address lease Time 5 The length of time the DHCP server will reserve the IP address for each computer We recommend that you leave the lease time set to Forever The default setting is Forever, meaning that any time a computer is assigned an IP address by the DHCP server, the IP address will not change for that particular computer Setting lease times for shorter intervals such as one day or one hour frees IP addresses after the specified period of time This also means that a particular computers IP address may change over time If you have set any of the other advanced features of the Router such as DMZ or client IP filters, these are dependent on the IP address For this reason, you will not want the IP address to change local domain name 6 The default setting is Belkin You can set a local domain name

(network name) for your network There is no need to change this setting unless you have a specific advanced need to do so You can name the network anything you want such as MY NETWORK Enhanced Wireless Router 38 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Viewing the dHCP Client list Page You can view a list of the computers (known as clients), which are connected to your network You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computers network interface card (NIC) Pressing the Refresh (4) button will update the list If there have been any changes, the list will be updated

(1)

(2)

(3)

(4) Enhanced Wireless Router 39 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Configuring the Wireless network settings The Wireless tab lets you make changes to the wireless network settings From this tab you can make changes to the wireless network name or Service Set Identifier (SSID), operating channel, encryption security settings, and configure the Router to be used as an access point Changing the Wireless network name (ssId) To identify your wireless network, a name called the SSID is used The SSID is your network name The default network name of the Router is Belkin_XXXXXX; the XXXXXX represent six digits that are unique to your Router Your network name will look something like Belkin_123456 You can change this to anything you choose, or you can leave it unchanged Keep in mind, if you decide to change your wireless network name, and there are other wireless networks operating in your area, your network name needs to be different from other wireless networks that may be operating in your area To change the SSID, type in the SSID that you want to use in the SSID field (1) and click Apply Changes (2) The change is immediate If you make a change to the SSID, your wireless-equipped computers may also need to be reconfigured to connect to your new network name Refer to the documentation of your wireless network adapter for information on making this change Enhanced Wireless Router 40

(1)

(2) note: Please periodically check for new Router firmware updates from the Utilities > Firmware update page Newer firmware can fix problems, add wireless features, and/or improve wireless performance

(see page 64) UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 2) 80211g only Setting the Router to this mode will allow only 80211g-compliant devices to join the network, keeping out any slower 80211b devices 3) 1x1 80211n Setting the Router to this mode will allow only 80211n-compliant devices to join the network, keeping out any slower 80211b/g devices 4) 80211b & 80211g & 1x1 80211n Setting the Router to this mode will allow 80211b-, 80211g-, and 80211n-compliant devices to join the network Changing the Wireless Channel There are a number of operating channels from which you can choose in the United States, there are 11 and in the United Kingdom (and most of Europe), there are 13 In a small number of other countries, there are other channel requirements Your Router is configured to operate on the proper channels for the country in which you reside The channel can be changed if needed If there are other wireless networks operating in your area, your network should be set to operate on a channel that is different than the other wireless networks Extension Channel The 80211n draft specification allows the use of a secondary channel to double the bandwidth (see Using the Bandwidth Switch on the next page) An appropriate extension channel will be displayed when operating in 40MHz mode (see Using the Wireless Mode Switch below) The channel can be changed if needed Using the Wireless Mode switch This switch allows you to set the Routers wireless modes There are several modes note: Some modes may require firmware updates to be enabled 1) off This mode will turn OFF the Routers access point, so no wireless devices can join the network Turning off the wireless function of your Router is a great way to secure your network when you are away from home for a long period of time, or dont want to use the wireless feature of the Router at a certain time Enhanced Wireless Router 41 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 1) 20MHz only Setting the Router to this mode allows only 20MHz operation This mode is compatible with draft 80211n-, 80211g-, and 80211b-compliant devices, but will limit draft 80211n-compliant devices bandwidth by half Reducing bandwidth to 20MHz-only operation might solve some wireless problems 2) 20MHz/40MHz auto Setting the Router to this mode allows it to switch automatically between 20MHz and 40MHz operation This mode enables 40MHz operation, to maximize speed for draft 80211n-compliant devices when conditions permit When a legacy 80211g access point is presented and occupies an adjacent secondary channel, the Router automatically reverts to 20MHz operation to maximize compatibility We recommend using this as the default mode 80211e/WMM Qos switch Allows you to turn ON or OFF wireless QoS Using the broadcast ssId feature note: This advanced feature should be employed by advanced users only For security, you can choose not to broadcast your networks SSID Doing so will keep your network name hidden from computers that are scanning for the presence of wireless networks To turn off the broadcast of the SSID, remove the check mark from the box next to Broadcast SSID, and then click Apply Changes The change is immediate Each computer now needs to be set to connect to your specific SSID; an SSID of ANY will no longer be accepted Refer to the documentation of your wireless network adapter for information on making this change Protected Mode switch Protected mode ensures proper operation of 80211g devices on your Enhanced network when 80211b devices are present or when there is heavy 80211b traffic in the operating environment If you are using a mix of Belkin Enhanced Wireless Cards and 80211b or 80211g cards on your network, protected mode should be used If you are in an environment where there is no other (or very little) 80211b wireless network traffic, best 80211g performance may be achieved with protected mode OFF If you are operating in an environment with HEAVY 80211b traffic or interference, best 80211g performance may be achieved with protected mode ON Wireless Enhanced performance is not affected by this setting Using the bandwidth switch This switch allows you to set the Routers wireless bandwidth modes There are several modes available:

Enhanced Wireless Router 42 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless security settings Your Enhanced Wireless Router is equipped with the latest security standard called Wi-Fi Protected Access 2 (WPA2) and the legacy security standard called Wired Equivalent Privacy (WEP) Your Router also supports the Wi-Fi Protected Setup (WPS) specification, which simplifies the setup of a wireless network WPS uses familiar methodologies, such as typing in a Personal Identification Number (PIN) or pushing a button, to enable users to automatically configure network names and strong WPA/WPA2 data encryption and authentication By default, wireless security is disabled To enable security, you will need to determine which standard you want to use To access the security settings, click Security on the Wireless tab Using Wi-fi Protected setup WPS recommends that you set up WPA/WPA2 (described on page 46) as your wireless security WPS does not provide additional security, but rather, simplifies the addition of wireless devices to your wireless network You may use either the Push Button Configuration (PBC) method or PIN method to allow a device access to your wireless network PbC: Push and hold the WPS button located on the front of your Router for three seconds and the security LED will flash, indicating that WPS has been initiated Then, initiate WPS on the client device within two minutes (Refer to your clients documentation on this procedure) The wireless device and Router will automatically exchange a security key and establish a secure connection PIn: The client device has a WPS PIN number (eight digits) that will be provided to you when you initiate the connection to the Router Enable WPS through the screen illustrated on the next page Enter the clients PIN into the Routers internal registrar (accessed through this screen) The client will be securely enrolled into your wireless network within two minutes Enhanced Wireless Router 43 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 1 Wi-Fi Protected Setup (WPS): Enabled or Disabled 2 Personal Identification Number (PIN) Method: In this method, a wireless client wishing to access your network must supply a 4- or 8-digit PIN to the Router After clicking Enroll, you must start WPS from the client within two minutes 3 Router PIN: If an external registrar is available, you may enter in the Routers PIN to the registrar Click Generate New PIN to change the PIN from the default value Click Restore Default PIN to reset the PIN value 4 Push Button Configuration (PBC) Method: PBC is an alternate method to connect to a WPS network Push the WPS button located on the front of the Router for three seconds, and then initiate the PBC on the client device Alternatively, push the Start PBC soft button to start this process 5 Manual Configuration Method: This section lists the default security settings to be set up if not using WPS Enhanced Wireless Router 44 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 WPa2 Requirements IMPoRTanT: In order to use WPA2 security, all your computers and wireless client adapters must be upgraded with patches, driver, and client utility software that supported WPA2 At the time of this User Manuals publication, a couple security patches are available, for free download, from Microsoft These patches work only with the Windows XP operating system Other operating systems are not supported at this time For Windows XP computers that do not have Service Pack 2 (SP2), a file from Microsoft called Windows XP Support Patch for Wireless Protected Access (KB 826942) is available for free download at http://supportmicrosoftcom/kb/826942 For Windows XP with Service Pack 2, Microsoft has released a free download to update the wireless client components to support WPA2

(KB971021) The update is available from: http://supportmicrosoftcom/kb/917021 IMPoRTanT: You also need to ensure that all your wireless client cards/adapters support WPA2, and that you have downloaded and installed the latest driver Most of the Belkin wireless cards have driver updates available for download from the Belkin support site: wwwbelkincom/networking Enhanced Wireless Router 45 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting WPa/WPa2 Encryption Like WPA security, WPA2 is available in both WPA2-Personal (PSK) mode and WPA2-Enterprise (RADIUS) mode Typically, WPA2-Personal (PSK) is the mode that will be used in a home environment, while WPA2-Enterprise (RADIUS) is implemented in a business environment where an external radius server distributes the network key to the clients automatically Your Router supports WPA2-Personal (PSK) 1 2 3 After youve set up your Router, go to the Security under Wireless and select WPA/WPA2-Personal (PSK) from the Security Mode drop-down menu (1) For Authentication, select WPA-PSK, WPA2-PSK, or WPA-

PSK + WPA2-PSK (2) This setting will have to be identical on the wireless clients that you set up WPA-PSK + WPA2-PSK mode will allow the Router to support clients running either WPA or WPA2 security Enter your pre-shared key (PSK) (3) This can be from eight to 63 characters and can be letters, numbers, or symbols This same key must be used on all of the wireless clients that you set up For example, your PSK might be something like: Smith family network key Click Apply Changes (4) to finish You must now set all wireless clients to match these settings

(3)

(1)

(2)

(4) IMPoRTanT: Make sure your wireless computers are updated to work with WPA2 and have the correct settings to get proper connection to the Router Enhanced Wireless Router 46 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting WEP Encryption note to Mac users: The Passphrase option will not operate with Apple AirPort To configure encryption for your Mac computer, set the encryption using the manual method described in the next section 1 Select 128-bit WEP or 64-bit WEP from the drop-down menu 2 After selecting your WEP encryption mode, you can enter you WEP key manually by typing in the hex WEP key manually, or you can type a passphrase in the PassPhrase field and click Generate to create a WEP key from the passphrase Click Apply Changes to finish You must now set all of your clients to match these settings 3 Encryption in the Router is now set Each of your computers on your wireless network will now need to be configured with the same passphrase Refer to the documentation of your wireless network adapter for information on making this change Enhanced Wireless Router 47 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Using a Hexadecimal Key A hexadecimal key is a mixture of numbers and letters from AF and 09 64-bit keys are 10 digits long and can be divided into five two-digit numbers 128-bit keys are 26 digits long and can be divided into 13 two-digit numbers For instance:

AF 0F 4B C3 D4 = 64-bit key C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key In the boxes below, make up your key by writing in two characters between AF and 09 You will use this key to program the encryption settings on your Router and your wireless computers note to Mac users: Original Apple AirPort products support 64-bit encryption only Apple AirPort 2 products can support 64-bit or 128-bit encryption Please check your product to see which version you are using If you cannot configure your network with 128-bit encryption, try 64-bit encryption Enhanced Wireless Router 48 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Using the access Point Mode note: This advanced feature should be employed by advanced users only The Router can be configured to work as a wireless network access point Using this mode will defeat the NAT IP sharing feature and DHCP server In AP mode, the Router will need to be configured with an IP address that is in the same subnet as the rest of the network that you will bridge to The default IP address is 1921682254 and subnet mask is 2552552550 These can be customized for your need 1 Enable the AP mode my selecting Enable in the Use as Access Point only page When you select this option, you will be able to change the IP settings 2 Set your IP settings to match your network Click Apply Changes 3 Connect a cable from the WAN port on the Router to your existing network The Router is now acting as an access point To access the Router advanced user interface again, type the IP address you specified into your browsers navigation bar You can set the encryption settings, MAC address filtering, SSID, and channel normally Enhanced Wireless Router 49 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting MaC address Control The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the wireless network note: This list applies only to wireless computers This list can be configured so any computer attempting to access the wireless network that is not specified in the filter list will be denied access When you enable this feature, you must enter the MAC address of each client (computer) to which you want to allow network access The Block feature lets you turn on and off access to the network easily for any computer without having to add and remove the computers MAC address from the list

(1)

(2)

(3)

(4)

(5) setting up an allow access list 1 Select the Allow radio button (1) to begin setting up a list of computers allowed to connect to the wireless network 2 Next, in the MAC Address field that is blank (3), type in the MAC address of the wireless computer you want to be able to access the wireless network, then click <<Add (4) 3 Continue to do this until all of the computers you want to add have been entered 4 Click Apply Changes (5) to finish Enhanced Wireless Router 50 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting up a deny access list The Deny Access list lets you specify computers that you DO NOT want to access the network Any computer in the list will not be allowed access to the wireless network All others will 1 Select the Deny radio button (2) to begin setting up a list of computers to be denied access to the wireless network 2 Next, in the MAC Address field that is blank (3), type in the MAC address of the wireless computer you want to deny access to the wireless network, then click <<Add (4) 3 Continue to do this until all of the computers you want to deny access to have been entered 4 Click Apply Changes (5) to finish

(1)

(2)

(3)

(4)

(5) Enhanced Wireless Router 51 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 The firewall also masks common ports that are frequently used to attack networks These ports appear to be stealth meaning that for all intents and purposes, they do not exist to a would-be hacker You can turn the firewall function off if needed; however, it is recommended that you leave the firewall enabled Disabling the firewall protection will not leave your network completely vulnerable to hacker attacks, but it is recommended that you leave the firewall enabled Configuring the firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including:

IP Spoofing Land Attack Ping of Death (PoD) Denial of Service (DoS) IP with zero length Smurf Attack TCP Null Scan SYN flood UDP flooding Tear Drop Attack ICMP defect RIP defect Fragment flooding Enhanced Wireless Router 52 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Configuring Internal forwarding settings The Virtual Servers function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network Since your internal computers are protected by a firewall, computers outside your network (over the Internet) cannot get to them because they cannot be seen A list of common applications has been provided in case you need to configure the Virtual Server function for a specific application If your application is not listed, you will need to contact the application vendor to find out which port settings you need Choosing an application Select your application from the drop-down list Click Add The settings will be transferred to the next available space in the screen Click Apply Changes to save the setting for that application To remove an application, select the number of the row that you want to remove then click Clear Manually Entering settings into the Virtual server To manually enter settings, enter the IP address in the space provided for the internal (server) machine, the port(s) required to pass (use a comma between multiple ports), select the port type (TCP or UDP), and click Apply Changes You can only pass one port per internal IP address Opening ports in your firewall can pose a security risk You can enable and disable settings very quickly It is recommended that you disable the settings when you are not using a specific application Enhanced Wireless Router 53 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting Client IP filters The Router can be configured to restrict access to the Internet, email, or other network services at specific days and times Restriction can be set for a single computer, a range of computers, or multiple computers To restrict Internet access to a single computer for example, enter the IP address of the computer you wish to restrict access to in the IP fields

(1) Next, enter 80 in both the port fields (2) Select Both (3) Select Block (4) You can also select Always to block access all of the time Select the day to start on top (5), the time to start on top (6), the day to end on the bottom (7), and the time to stop (8) on the bottom Select Enable (9) Click Apply Changes The computer at the IP address you specified will now be blocked from Internet access at the times you specified note: Be sure you have selected the correct time zone under Utilities> System Settings> Time Zone

(5)

(6)

(1)

(2)

(3)

(4)

(7)

(8)

(9) Enhanced Wireless Router 54 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Enabling the demilitarized Zone (dMZ) The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application Use this feature on a temporary basis The computer in the DMZ is NOT protected from hacker attacks To put a computer in the DMZ, enter the last digits of its IP address in the IP field and select Enable Click Apply Changes for the change to take effect If you are using multiple static WAN IP addresses, it is possible to select which WAN IP address the DMZ host will be directed to Type in the WAN IP address you wish the DMZ host to direct to, enter the last two digits of the IP address of the DMZ host computer, select Enable and click Apply Changes Enhanced Wireless Router 55 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Using dynamic dns The Dynamic DNS service allows you to alias a dynamic IP address to a static host name in any of the many domains DynDNSorg offers, allowing your network computers to be more easily accessed from various locations on the Internet DynDNSorg provides this service, for up to five host names, free to the Internet community The Dynamic DNSSM service is ideal for a home website, file server, or to make it easy to access your home PC and stored files while youre at work Using the service can ensure that your host name always points to your IP address, no matter how often your ISP changes it When your IP address changes, your friends and associates can always locate you by visiting yournamedyndnsorg instead!

To register free for your Dynamic DNS host name, please visit http://wwwdyndnsorg setting up the Routers dynamic dns Update Client You must register with DynDNSorgs free update service before using this feature Once you have your registration, follow the directions below 1 2 3 4 Select DynDNS as the DDNS Service (1) Enter your DynDNSorg user name in the User Name field (2) Enter your DynDNSorg password in the Password field (3) Enter the DynDNSorg domain name you set up with DynDNSorg in the Domain Name field (4) 5 Click Update Dynamic DNS (5) to update your IP address Whenever your IP address assigned by your ISP changes, the Router will automatically update DynDNSorgs servers with your new IP address You can also do this manually by clicking the Update Dynamic DNS button (5) Enhanced Wireless Router 56

(1)

(2)

(3)

(4)

(5) UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 blocking an ICMP Ping Computer hackers use what is known as pinging to find potential victims on the Internet By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there The Router can be set up so it will not respond to an ICMP ping from the outside This heightens your Routers security level Utilities The Utilities screen lets you manage different parameters of the Router and perform certain administrative functions

(1) To turn off the ping response, select Block ICMP Ping (1) and click Apply Changes The Router will not respond to an ICMP ping Enhanced Wireless Router 57 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Restarting the Router Sometimes it may be necessary to restart or reboot the Router if it begins working improperly Restarting or rebooting the Router will NOT delete any of your configuration settings 3 The following message will appear Restarting the Router can take up to 60 seconds It is important not to turn off the power to the Router during the restart Restarting the Router to Restore normal operation 1 Click the Restart Router button 2 The following message will appear Click OK 4 A 60-second countdown will appear on the screen When the countdown reaches zero, the Router will be restarted The Router home page should appear automatically If not, type in the Routers address (default = 19216821) into the navigation bar of your browser Enhanced Wireless Router 58 USING THE WEB-BASED ADVANCED USER INTERFACE Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10 Restoring Factory Default Settings Using this option will restore all of the settings in the Router to the factory (default) settings. It is recommended that you back up your settings before you restore all of the defaults. 3. The following message will appear. Restoring the defaults includes restarting the Router. It can take up to 60 seconds. It is important not to turn the power to the Router off during the restart. 1. Click the Restore Defaults button. 2. The following message will appear. Click OK. 4. A 60-second countdown will appear on the screen. When the countdown reaches zero, the Routers defaults will be restored. The Router home page should appear automatically. If it does not, type in the Routers address (default = 192.168.2.1) into the navigation bar of your browser. Enhanced Wireless Router 59 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 saving a Current Configuration You can save your current configuration by using this feature Saving your configuration will allow you to restore it later if your settings are lost or changed It is recommended that you back up your current configuration before performing a firmware update 1 Click Save A window called File Download will open Click Save Enhanced Wireless Router 60 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 2 A window will open that allows you to select the location where you want to save the configuration file Select a location You can name the file anything you want, or use the default name userconf Be sure to name the file so you can locate it yourself later When you have selected the location and name of the file, click Save 3 When the save is complete, you will see the window below Click Close The configuration is now saved Enhanced Wireless Router 61 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Restoring a Previous Configuration This option will allow you to restore a previously saved configuration 1 Click Browse A window will open that allows you to select the location of the configuration file All configuration files end with a conf Locate the configuration file you want to restore and double-click on it Enhanced Wireless Router 62 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 2 You will be asked if you want to continue Click OK 3 A reminder window will appear It will take up to 60 seconds for the configuration restoration to complete Click OK 4 A 60-second countdown will appear on the screen When the countdown reaches zero, the Routers configuration will be restored The Routers home page should appear automatically If not, type in the Routers address (default = 19216821) into the navigation bar of your browser Enhanced Wireless Router 63 USING THE WEB-BASED ADVANCED USER INTERFACE Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10 Updating the Firmware From time to time, Belkin may release new versions of the Routers firmware. Firmware updates contain feature improvements and fixes to problems that may have existed. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Routers firmware to the latest version. Checking for a New Version of Firmware The Check Firmware (1) button allows you to instantly check for a new version of firmware. When you click the button, a new browser window will appear informing you that either no new firmware is available or that there is a new version available. If a new version is available, you will have the option to download it. Downloading a New Version of Firmware If you click the Check Firmware button and a new version of firmware is available, you will see a screen similar to the one here:

(1) Enhanced Wireless Router 64 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 1 To download the new version of firmware, click Download 2 A window will open that allows you to select the location where you want to save the firmware file Select a location You can name the file anything you want, or use the default name Be sure to locate the file in a place where you can locate it yourself later When you have selected the location, click Save 3 When the save is complete, you will see the following window Click Close The download of the firmware is complete To update the firmware, follow the next steps in Updating the Routers Firmware Enhanced Wireless Router 65 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Updating the Routers firmware 1 In the Firmware Update page, click Browse A window will open that allows you to select the location of the firmware update file 2 Browse to the firmware file you downloaded Select the file by double-clicking on the file name Enhanced Wireless Router 66 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 3 The Update Firmware box will now display the location and name of the firmware file you just selected Click Update 5 You will see one more message This message tells you that the Router may not respond for as long as one minute as the firmware is loaded into the Router and the Router is rebooted Click OK 6 A 60-second countdown will appear on the screen When the countdown reaches zero, the Router firmware update will be complete The Router home page should appear automatically If not, type in the Routers address (default = 19216821) into the navigation bar of your browser 4 You will be asked if you are sure you want to continue Click OK Enhanced Wireless Router 67 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Changing system settings The System Settings page is where you can enter a new administrator password, set the time zone, enable remote management, and turn on and off the NAT function of the Router setting or Changing the administrator Password The Router ships with NO password entered If you wish to add a password for greater security, you can set a password here Write down your password and keep it in a safe place, as you will need it if you need to log into the Router in the future It is also recommended that you set a password if you plan to use the remote management feature of your Router Changing the login Time-out setting The login time-out option allows you to set the period of time that you can be logged into the Routers advanced setup interface The timer starts when there has been no activity For example, imagine you have made some changes in the advanced setup interface, then left your computer alone without clicking Logout Assuming the time-out is set to 10 minutes, 10 minutes after you leave, the login session will expire You will have to log into the Router again to make any more changes The login time-out option is for security purposes and the default is set to 10 minutes note: Only one computer can be logged into the Routers advanced setup interface at one time Enhanced Wireless Router 68 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 setting the Time and Time Zone The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server This allows the Router to synchronize the system clock to the global Internet The synchronized clock in the Router is used to record the security log and control client filtering Select the time zone that you reside in You have the option to select a primary and a backup NTP server to keep your Routers clock synchronized Select your desired NPT server from the drop-down box, or simply keep it as is If you reside in an area that observes daylight saving, then place a check mark in the box next to Enable Daylight Saving The system clock may not update immediately Allow at least 15 minutes for the Router to contact the time servers on the Internet and get a response You cannot set the clock yourself Enabling Remote Management Before you enable this advanced feature of your Belkin Router, MaKE sURE yoU HaVE sET THE adMInIsTRaToR PassWoRd Remote management allows you to make changes to your Routers settings from anywhere on the Internet There are two methods of remotely managing the Router The first is to allow access to the Router from anywhere on the Internet by selecting Any IP address can remotely manage the Router By typing in your WAN IP address from any computer on the Internet, you will be presented with a login screen where you need to type in the password of your Router The second method is to allow a specific IP address only to remotely manage the Router This is more secure, but less convenient To use this method, enter the IP address you know you will be accessing the Router from in the space provided and select Only this IP address can remotely manage the Router Before you enable this function, it is STRONGLY RECOMMENDED that you set your administrator password Leaving the password empty will potentially open your Router to intrusion Advanced Feature: The Remote Access Port option allows you to configure the desired Remote Access Port for Remote Management feature The default access port is set to port 80 Enhanced Wireless Router 69 UsIng THE WEb-basEd adVanCEd UsER InTERfaCE table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Enabling/disabling UPnP UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Router It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant Some applications require the Routers firewall to be configured in a specific way to operate properly This usually requires opening TCP and UDP ports, and in some instances, setting trigger ports An application that is UPnP-compliant has the ability to communicate with the Router, basically telling the Router which way it needs the firewall configured The Router ships with the UPnP feature disabled If you are using any applications that are UPnP-compliant, and wish to take advantage of the UPnP features, you can enable the UPnP feature Simply select Enable in the UPnP Enabling section of the Utilities page Click Apply Changes to save the change Enabling/disabling auto firmware Update This innovation provides the Router with the built-in capability to automatically check for a new version of firmware and alert you that the new firmware is available When you log into the Routers advanced interface, the Router will perform a check to see if new firmware is available If so, you will be notified You can choose to download the new version or ignore it Enhanced Wireless Router 70 ManUally ConfIgURIng nETWoRK sETTIngs table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Set up the computer that is connected to the cable or DSL modem FIRST using these steps You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet Manually Configuring network settings in Mac os up to 9x In order for your computer to properly communicate with your Router, you will need to change your Mac computers TCP/IP settings to DHCP 1 Pull down the Apple menu Select Control Panels and select TCP/IP 4 If not already set, at Configure:, choose Using DHCP Server This will tell the computer to obtain an IP address from the Router 2 You will see the TCP/IP control panel Select Ethernet Built-In or Ethernet in the Connect via: drop-down menu (1)

(1)

(2) 3 Next to Configure (2), if Manually is selected, your Router will need to be set up for a static IP connection type Write the address information in the table below You will need to enter this information into the Router Enhanced Wireless Router 71 5 Close the window If you made any changes, the following window will appear Click Save Restart the computer When the computer restarts, your network settings are now configured for use with the Router ManUally ConfIgURIng nETWoRK sETTIngs table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Manually Configuring network settings in Mac os X 1 Click on the System Preferences icon 2 Select Network from the System Preferences menu

(1)

(2)

(4)

(3) 3 Select Built-in Ethernet (1) next to Show in the Network menu 4 Select the TCP/IP tab (2) Next to Configure: (3), you should see Manually or Using DHCP If you do not, check the PPPoE tab

(4) to make sure that Connect using PPPoE is NOT selected If it is, you will need to configure your Router for a PPPoE connection type using your user name and password Enhanced Wireless Router 72 ManUally ConfIgURIng nETWoRK sETTIngs table of c ontents sections 1 2 3 4 5 6 7 8 9 10 5 If Manually is selected, your Router will need to be set up for a static IP connection type Write the address information in the table below You will need to enter this information into the Router 6 If not already selected, select Using DHCP next to Configure:

(3), then click Apply Now your network adapter(s) are now configured for use with the Router

(1)

(2)

(4)

(3) Enhanced Wireless Router 73 ManUally ConfIgURIng nETWoRK sETTIngs table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Manually Configuring network settings in Windows 2000, nT, XP, or Vista 1 Click Start, Settings, then Control Panel 2 Double-click on the Network and dial-up connections icon

(Windows 2000) or the Network icon (Windows XP or Vista) 3 Right-click on the Local Area Connection associated with your network adapter and select Properties from the drop-down menu 4 5 In the Local Area Connection Properties window, click Internet Protocol (TCP/IP) and click the Properties button The screen on the right will appear If Use the following IP address (2) is selected, your Router will need to be set up for a static IP connection type Write the address information in the table below You will need to enter this information into the Router

(1)

(2)

(3) 6 If not already selected, select Obtain an IP address automatically

(1) and Obtain DNS server address automatically (3) Click OK your network adapter(s) are now configured for use with the Router Enhanced Wireless Router 74 ManUally ConfIgURIng nETWoRK sETTIngs table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Manually Configuring network settings in Windows 98sE or Me 1 Right-click on My Network Neighborhood and select Properties from the drop-down menu 6 Click the DNS Configuration tab (1) Write the DNS address(es) in the chart 2 Select TCP/IP -> settings for your installed network adapter You will see the following window 7 If not already selected, select Obtain IP address automatically in the IP Address tab Click OK 3 If Specify an IP address is selected, your Router will need to be set up for a static IP connection type Write the address information in the table below You will need to enter this information into the Router Restart the computer When the computer restarts, your network adapter(s) are now configured for use with the Router 4 Write in the IP address and subnet mask from the IP Address tab (3) 5 Click the Gateway tab (2) Write the gateway address down in the chart

(1)

(2)

(3) Enhanced Wireless Router 75 RECoMMEndEd WEb bRoWsER sETTIngs table of c ontents sections 1 2 3 4 5 6 7 8 9 10 In most cases, you will not need to make any changes to your web browsers settings If you are having trouble accessing the Internet or the Web-Based Advanced User Interface, then change your browsers settings to the recommended settings in this section Internet Explorer 40 or Higher 1 Start your web browser Select Tools then Internet Options 2 In the Internet Options screen, there are three selections: Never dial a connection, Dial whenever a network connection is not present, and Always dial my default connection If you can make a selection, select Never dial a connection If you cannot make a selection, go to the next step Enhanced Wireless Router 76 RECoMMEndEd WEb bRoWsER sETTIngs table of c ontents sections 1 2 3 4 5 6 7 8 9 10 3 Under the Internet Options screen, click on Connections and select LAN Settings 4 Make sure there are no check marks next to any of the displayed options: Automatically detect settings, Use automatic configuration script, and Use a proxy server Click OK Then click OK again in the Internet Options page netscape navigator 40 or Higher 1 2 Start Netscape Click on Edit then Preferences In the Preferences window, click on Advanced then select Proxies In the Proxies window, select Direct connection to the Internet Enhanced Wireless Router 77 TROUBLESHOOTING Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10 Problem:

Setup Assistant CD does not automatically start. Solution:

If the CD-ROM does not start the Setup Assistant automatically, it could be that the computer is running other applications that are interfering with the CD drive. 1. If the Setup Assistant screen does not appear within 1520 seconds, open up your CD-ROM drive by double-clicking on the My Computer icon that is located on your desktop. 2. Next, double-click on the CD-ROM drive that the Setup Assistant Software CD has been placed in to start the installation. Enhanced Wireless Router 78 TROUBLESHOOTING Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10 3. 4. The Setup Assistant should start within a few seconds. If, instead, a window appears showing the files on the CD, double-click on the icon labeled SetupAssistant. If the Setup Assistant still does not start, reference the section titled Manually Configuring Network Settings (page 71) of this User Manual for an alternative setup method. Enhanced Wireless Router 79 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

Setup Assistant cannot find my Router solution:

If the Setup Assistant is not able to find the Router during the installation process, please check the following items:

1 If the Setup Assistant is not able to find the Router during the installation process, there may be third-party firewall software installed on the computer attempting to access the Internet Examples of third-party firewall software are ZoneAlarm, BlackICE PC Protection, McAfee Personal Firewall, and Norton Personal Firewall If you do have firewall software installed on your computer, please make sure that you properly configure it You can determine if the firewall software is preventing Internet access by temporarily turning it off If, while the firewall is disabled, Internet access works properly, you will need to change the firewall settings to function properly when it is turned on Please refer to the instructions provided by the publisher of your firewall software for instructions on configuring the firewall to allow Internet access 2 Unplug power to the Router for 10 seconds, and then plug the power back into the Router Ensure that the Routers router LED is on; it should be solid GREEN If not, check to make sure that the AC adapter is connected to the Router and plugged into a wall outlet 3 Ensure that you have a cable connected between the network

(Ethernet) port on the back of the computer and one of the wired ports on the back of the Router note: The computer should NOT be connected to the port labeled to Modem on the back of the Router 4 Try shutting down and restarting your computer, then rerunning the Setup Assistant If the Setup Assistant is still unable to find the Router, reference the section titled Manually Configuring Network Settings for installation steps Enhanced Wireless Router 80 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

Setup Assistant cannot connect my Router to the Internet solution:

If the Setup Assistant is not able to connect the Router to the Internet, please check the following items:

1 Use the troubleshooting suggestions within the Setup Assistant 2 If your ISP requires a user name and password, make sure that you have typed in your user name and password correctly Some user names require that the ISPs domain may be at the end of the name Example: myname@myispcom The @myispcom part of the user name may need to be typed as well as your user name If you continue to have no Internet connection, reference the section titled Manually Configuring Network Settings (page 71 of this User Manual for an alternative setup method) Problem:

The Setup Assistant completed installation, but my web browser doesnt work I am unable to connect to the Internet The modem LED on my Router is off, and the internet LED is blinking solution:

If you cannot connect to the Internet, and the modem LED is off, and the internet LED is blinking, the problem may be that your modem and Router are not connected properly 1 Make sure the network cable between the modem and the Router is connected The cable should be connected at one end to the Routers to Modem port, and at the other end to the network port on your modem 2 Unplug the cable or DSL modem from its power source for three minutes After three minutes, plug the modem back into its power source This may force the modem to properly recognize the Router 3 Unplug the power to your Router, wait 10 seconds, and then reconnect the power This will cause the Router to reattempt communication with the modem If the modem LED on the Router is not lit after completing these steps, please contact Belkin Technical Support 4 Try shutting down and restarting your computer Enhanced Wireless Router 81 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

Problem:

The Setup Assistant completed installation, but my web browser doesnt work I am unable to connect to the Internet The modem LED on my Router is on, and the internet LED is blinking solution:

1 2 3 4 If you cannot connect to the Internet, the modem LED is on, and the internet LED is blinking, the problem may be that your connection type may not match the ISPs connection If you have a static IP address connection, your ISP must assign you the IP address, subnet mask, and gateway address Please refer to the section entitled Alternate Setup Method for details on changing this setting If you have a PPPoE connection, your ISP will assign you a user name and password and sometimes a service name Make sure the Routers connection type is configured to PPPoE and the settings are entered properly Please refer to the section entitled Alternate Setup Method for details on changing this setting You may need to configure your Router to meet the specific requirements of your ISP To search our knowledge base for ISP-specific issues, go to: http://webbelkincom/support and type in ISP If you are still unable to access the Internet after verifying these settings, please contact Belkin Technical Support The Setup Assistant completed, but my web browser doesnt work I am unable to connect to the Internet The modem LED on my Router is blinking, and the internet LED is solid solution:

1 2 If the modem LED is blinking, and the internet LED is solid, but you are unable to access the Internet, there may be third-

party firewall software installed on the computer attempting to access the Internet Examples of third-party firewall software are ZoneAlarm, BlackICE PC Protection, McAfee Personal Firewall, and Norton Personal Firewall If you do have firewall software installed on your computer, please make sure that you properly configure it You can determine if the firewall software is preventing Internet access by temporarily turning it off If, while the firewall is disabled, Internet access works properly, you will need to change the firewall settings to function properly when it is turned on 3 Please refer to the instructions provided by the publisher of your firewall software for instructions on configuring the firewall to allow Internet access If you are still unable to access the Internet after disabling any firewall software, please contact Belkin Technical Support Enhanced Wireless Router 82 TROUBLESHOOTING Table of Contents SECTIONS 1 2 3 4 5 6 7 8 9 10 Problem:

I cant connect to the Internet wirelessly. Solution:

If you are unable to connect to the Internet from a wireless computer, please check the following items:

1. Make sure the LEDs on the front panel are shown as below:

The router LED should be on. The modem LED should be on, and not blinking. The internet LED should be on, and not blinking. The wireless LED should be on, and not blinking. 2. Open your wireless utility software by clicking on the icon in the system tray at the bottom, right-hand corner of the screen. 3. The exact window that opens will vary depending on the model of wireless card you have; however, any of the utilities should have a list of Available Networksthose wireless networks it can connect to. Does the name of your wireless network appear in the results?

Yes, my network name is listedgo to the troubleshooting solution titled I cant connect to the Internet wirelessly, but my network name is listed. No, my network name is not listedgo to the troubleshooting solution titled I cant connect to the Internet wirelessly, and my network name is not listed. Enhanced Wireless Router 83 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

I cant connect to the Internet wirelessly, but my network name is listed solution:

If the name of your network is listed in the Available Networks list, please follow the steps below to connect wirelessly:

1 Click on the correct network name in the Available Networks list 2 If the network has security (encryption) enabled, you will need to enter the network key For more information regarding security, see the section entitled Changing the Wireless Security Settings 3 Within a few seconds, the tray icon in the lower, right-hand corner of your screen should turn green, indication of a successful connection to the network Problem:

I cant connect to the Internet wirelessly, and my network name is not listed solution:

If the correct network name is not listed under Available Networks in the wireless utility, please attempt the following troubleshooting steps:

1 Temporarily move computer, if possible, five to 10 feet from the Router Close the wireless utility, and reopen it If the correct network name now appears under Available Networks, you may have a range or interference problem Please see the suggestions discussed in the section titled Placement of your Enhanced Wireless Router of this User Manual 2 Using a computer that is connected to the Router via a network cable (as opposed to wirelessly), ensure that Broadcast SSID is enabled This setting is found on the Routers wireless Channel and SSID configuration page If you are still unable to access the Internet after completing these steps, please contact Belkin Technical Support Enhanced Wireless Router 84 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

My wireless network performance is inconsistent. Data transfer is sometimes slow. Signal strength is poor. Difficulty establishing and/or maintaining a Virtual Private Network (VPN) connection. solution:

Wireless technology is radio-based, which means connectivity and the throughput performance between devices decreases when the distance between devices increases Other factors that will cause signal degradation (metal is generally the worst culprit) are obstructions such as walls and metal appliances Note also that connection speed may decrease as you move farther away from the Router In order to determine if wireless issues are related to range, we suggest temporarily moving the computer, if possible, five to 10 feet from the Router Changing the wireless channelDepending on local wireless traffic and interference, switching the wireless channel of your network can improve performance and reliability The default channel the Router is shipped with is channel 11; you may choose from several other channels depending on your region See the section on page 41 entitled Changing the Wireless Channel for instructions on how to choose other channels limiting the wireless transmit rateLimiting the wireless transmit rate can help improve the maximum wireless range and connection stability Most wireless cards have the ability to limit the transmission rate To change this property, go to the Windows Control Panel, open Network Connections and double-click on your wireless cards connection In the properties dialog, select the Configure button on the General tab

(Windows 98 users will have to select the wireless card in the list box and then click Properties), then choose the Advanced tab and select the rate property Wireless client cards are usually set to automatically adjust the wireless transmit rate for you, but doing so can cause periodic disconnects when the wireless signal is too weak; as a rule, slower transmission rates are more stable Experiment with different connection rates until you find the best one for your environment Note that all available transmission rates should be acceptable for browsing the Internet For more assistance, see your wireless cards user manual Enhanced Wireless Router 85 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

I am having difficulty setting up Wired Equivalent Privacy (WEP) security on my Belkin Router solution:

Log into your Router 1 Open your web browser and type in the IP address of the Router (The Routers default is 19216821) Log into your Router by clicking on the Login button in the top right-hand corner of the screen You will be asked to enter your password If you never set a password, leave the Password field blank and click Submit Click the Wireless tab on the left of your screen Select the Encryption or Security tab to get to the security settings page 2 Select 128-bit WEP from the drop-down menu 3 After selecting your WEP encryption mode, you can type in your hex WEP key manually, or you can type in a passphrase in the Passphrase field and click Generate to create a WEP key from the passphrase Click Apply Changes to finish You must now set all of your clients to match these settings A hex (hexadecimal) key is a mixture of numbers and letters from A-F and 0-9 For 128-bit WEP, you need to enter 26 hex keys For example:

C3 03 0f af 4b b2 C3 d4 4b C3 d4 E7 E4 = 128-bit key 4 Click Apply Changes to finish Encryption in the Wireless Router is now set Each of your computers on your wireless network will now need to be configured with the same security settings WaRnIng: If you are configuring the Wireless Router or Access Point from a computer with a wireless client, you will need to ensure that security is turned on for this wireless client If this is not done, you will lose your wireless connection note to Mac users: Original Apple AirPort products support 64-bit encryption only Apple AirPort 2 products can support 64-bit or 128-

bit encryption Please check your Apple AirPort product to see which version you are using If you cannot configure your network with 128-bit encryption, try 64-bit encryption Enhanced Wireless Router 86 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin client card solution:

The client card must use the same key as the Router For instance, if your Router uses the key 00112233445566778899AABBCC, then the client card must be set to the exact same key 1 Double-click the Signal Indicator icon to bring up the Wireless Network screen 2 The Advanced button will allow you to view and configure more options of your card 3 Once the Advanced button is clicked, the Belkin Wireless LAN Utility will appear This Utility will allow you to manage all the advanced features of the Belkin Wireless Card 4 Under the Wireless Network Properties tab, select a network name from the Available Networks list and click the Properties button 5 Under Data Encryption, select WEP 6 Ensure that the check box The key is provided for me automatically at the bottom is unchecked If you are using this computer to connect to a corporate network, please consult your network administrator if this box needs to be checked Type your WEP key in the Network key box 7 Important: A WEP key is a mixture of numbers and letters from A-F and 0-9 For 128-bit WEP, you need to enter 26 keys This network key needs to match the key you assign to your Router For example:

C3 03 0f af 4b b2 C3 d4 4b C3 d4 E7 E4 = 128-bit key 8 Click OK, and then Apply to save the settings If you are not using a Belkin wireless client card, please consult the manufacturers user manual for that wireless client card Enhanced Wireless Router 87 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

Do Belkin products support WPA/WPA2?

solution:

To use WPA security, all your clients must be upgraded to drivers and software that support it At the time of this FAQ publication, a security patch download is available, for free, from Microsoft This patch works only with the Windows XP operating system Download the patch here:

Download the patch here: http://wwwmicrosoftcom/downloadS/details aspx?FamilyID=662bb74d-e7c1-48d6-95ee-1459234f4483 You also need to download the latest driver for your Belkin 80211g Wireless Desktop or Notebook Network Card from the Belkin support site Other operating systems are not supported at this time Microsofts patch only supports devices with WPA-enabled drivers such as Belkin 80211g products Download the latest driver at http://wwwbelkincom/support Problem:

I am having difficulty setting up Wireless Protected Access (WPA) security on my Belkin Router for a home network solution:

1 2 From the Security Mode drop-down menu, select WPA-PSK

(no server) Enter your pre-shared key This can be from eight to 63 characters and can be letters, numbers, symbols, or spaces This same key must be used on all of the clients that you set up For example, your PSK might be something like: Smith family network key 3 Click Apply Changes to finish You must now set all clients to match these settings Enhanced Wireless Router 88 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

I am having difficulty setting up Wireless Protected Access (WPA) security on a Belkin wireless client card for a home network solution:

Clients must use the same key that the G Wireless Router or access point uses For instance, if the key is Smith Family Network Key in the G Wireless Router or access point, the clients must also use that same key 1 Double-click the Signal Indicator icon to bring up the Wireless Network Utility screen The Advanced button will allow you to view and configure more options of your client card 4 Under Network Authentication, select WPA-PSK (no server) 2 Once the Advanced button is clicked, the Belkin Wireless Utility will appear This Utility will allow you to manage all the advanced features of the Belkin wireless card 3 Under the Wireless Network Properties tab, select a network name from the Available Networks list and click the Properties button Type your WPA key in the Network key box 5 Important: WPA-PSK is a combination of numbers and letters from A-Z and 0-9 For WPA-PSK, you can enter eight to 63 characters This network key needs to match the key you assign to your Router 6 Click OK, then Apply to save the settings Enhanced Wireless Router 89 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Problem:

I am NOT using a Belkin client card for a home network and I am having difficulty setting up Wireless Protected Access (WPA) security solution:

If you are not using a Belkin Wireless Desktop or Wireless Notebook Network Card that is not equipped with WPA-enabled software, a file from Microsoft called Windows XP Support Patch for Wireless Protected Access is available for free download Download the patch from Microsoft by searching the knowledge base for Windows XP WPA note: The file that Microsoft has made available works only with Windows XP Other operating systems are not supported at this time You also need to ensure that the wireless cards manufacturer supports WPA and that you have downloaded and installed the latest driver from their support site Supported Operating Systems:

Windows XP Professional Windows XP Home Edition 1 Under Windows XP, click Start > Control Panel >

Network Connections 2 Right-clicking on the Wireless Networks tab will display the following screen Ensure the Use Windows to configure my wireless network settings check box is checked Enhanced Wireless Router 90 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 3 Under the Wireless Networks tab, click the Configure button and you will see the following screen 4 For a home or small business user, select WPA-PSK under Network Administration note: Select WPA (with radius server) if you are using this computer to connect to a corporate network that supports an authentication server such as a radius server Please consult your network administrator for further information 5 Type in your encryption key in the Network key box Important: Enter your pre-shared key This can be from eight to 63 characters and can be letters, numbers, or symbols This same key must be used on all of the clients that you set up 6 Click OK to apply settings Enhanced Wireless Router 91 TRoUblEsHooTIng table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Whats the difference between 80211g and draft 80211n?

Currently there are three commonly used wireless networking standards, which transmit data at very different maximum speeds Each is based on the designation for certifying network standards The most common wireless networking standard, 80211g, can transmit information up to 54Mbps; 80211a also supports up to 54Mbps, but in the 5GHz frequency; and 80211n draft specification can connect at up to 300Mbps See the following chart for more detailed information Wireless Comparison Chart Wireless Technology g

(80211g) Enhanced n and n+

n1

(1x1 draft 80211n)

(draft 80211n with MIMo)

(draft 80211n with MIMo) speed/data Rate*

frequency Compatibility Up to 54Mbps*

Up to 150Mbps*

Up to 300Mbps*

Up to 300Mbps*

Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 24GHz Compatible with 80211b/g Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 24GHz Compatible with 80211b/g, draft 80211n, and Belkin G+

MIMO Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 24GHz Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 24GHz Compatible with draft 80211n and 80211b/g Compatible with draft 80211n and 80211b/g Coverage*

Up to 400 ft*

Up to 1,000 ft*

Up to 1,200 ft*

Up to 1,400 ft*

advantage Common widespread use for Internet sharing Better coverage and consistent speed and range Enhanced speed and coverage Leading edge best coverage and throughput

*Distance and connection speeds will vary depending on your networking environment Technical support You can find technical support information at http://wwwbelkincom/

networking or wwwbelkincom/support/

Enhanced Wireless Router 92 InfoRMaTIon table of c ontents sections 1 2 3 4 5 6 7 8 9 10 fCC statement dEClaRaTIon of ConfoRMITy WITH fCC RUlEs foR ElECTRoMagnETIC CoMPaTIbIlITy We, Belkin International, Inc, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the device, f6d4230-4 complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Caution: Exposure to Radio frequency Radiation The device shall be used in such a manner that the potential for human contact during normal operation is minimized This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body federal Communications Commission notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the distance between the equipment and the receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help For IEEE 80211b/g products in the USA market, only channels 1 through 11 can be operated Selection of other channels is not possible This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter Enhanced Wireless Router 93 InfoRMaTIon table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Modifications The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin International, Inc, may void the users authority to operate the equipment Canada-Industry Canada (IC) The wireless radio of this device complies with RSS 210 Industry Canada This Class B digital apparatus complies with Canadian ICES-003 Operation is subject to the following two conditions:

1) 2) this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device Cet appareil numrique de la classe B conforme la norme NMB-003 du Canada IMPoRTanT noTE:

IC Radiation Exposure statement This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body Europe-European Union notice Radio products with the CE 0682 or CE alert marking comply with the R&TTE Directive (1995/5/EC) issued by the Commission of the European Community Compliance with this directive implies conformity to the following European Norms (in brackets are the equivalent international standards) To determine the type of transmitter, check the identification label on your Belkin product EN 60950-1 (IEC60950) Product Safety EN 300 328 Technical requirement for radio equipment EN 301 489 General EMC requirements for radio equipment Products with the CE marking comply with the EMC Directive (89/336/

EEC) and the Low Voltage Directive (72/23/EEC) issued by the Commission of the European Community Compliance with these directives implies conformity to the following European Norms (in brackets are the equivalent international standards) EN 55022 (CISPR 22) Electromagnetic Interference EN 55024 (IEC61000-4-2,3,4,5,6,8,11) Electromagnetic Immunity EN 61000-3-2 (IEC610000-3-2) Power Line Harmonics EN 61000-3-3 (IEC610000) Power Line Flicker EN 60950-1 (IEC60950-1) Product Safety Products that contain the radio transmitter are labeled with CE 0682 or CE alert marking and may also carry the CE logo Enhanced Wireless Router 94 InfoRMaTIon table of c ontents sections 1 2 3 4 5 6 7 8 9 10 belkin International, Inc, limited 1-year Product Warranty What this warranty covers Belkin International, Inc (Belkin) warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship What the period of coverage is Belkin warrants the Belkin product for one year What will we do to correct problems?

Product Warranty. Belkin will repair or replace, at its option, any defective product free of charge (except for shipping charges for the product) Belkin reserves the right to discontinue any of its products without notice, and disclaims any limited warranty to repair or replace any such discontinued products In the event that Belkin is unable to repair or replace the product (for example, because it has been discontinued), Belkin will offer either a refund or a credit toward the purchase of another product from Belkincom in an amount equal to the purchase price of the product as evidenced on the original purchase receipt as discounted by its natural use What is not covered by this warranty?

All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkins request at the sole expense of the purchaser, or if Belkin determines that the Belkin product has been improperly installed, altered in any way, or tampered with The Belkin Product Warranty does not protect against acts of God such as flood, earthquake, lightning, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (ie brownouts or sags), non-authorized program, or system equipment modification or alteration How to get service To get service for your Belkin product you must take the following steps:

1 Contact Belkin International, Inc, at 501 W Walnut St, Compton CA 90220, Attn: Customer Service, or call (800)-223-5546, within 15 days of the Occurrence Be prepared to provide the following information:

a The part number of the Belkin product b Where you purchased the product c When you purchased the product d Copy of original receipt 2 Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim Enhanced Wireless Router 95 InfoRMaTIon table of c ontents sections 1 2 3 4 5 6 7 8 9 10 Belkin reserves the right to review the damaged Belkin product All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment The cost, if any, of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser Damaged equipment must remain available for inspection until the claim is finalized Whenever claims are settled, Belkin reserves the right to be subrogated under any existing insurance policies the purchaser may have How state law relates to the warranty THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state Some states do not allow the exclusion or limitation of incidental, consequential, or other damages, so the above limitations may not apply to you Enhanced Wireless Router 96 Belkin International, Inc 501 West Walnut Street Los Angeles, CA 90220, USA 310-898-1100 310-898-1111 fax Belkin Ltd Express Business Park, Shipton Way Rushden, NN10 6GL United Kingdom

+44 (0) 1933 35 2000

+44 (0) 1933 31 2000 fax Belkin BV Boeing Avenue 333 1119 PH Schiphol-Rijk The Netherlands

+31 (0) 20 654 7300

+31 (0) 20 654 7349 fax Belkin Ltd 4 Pioneer Avenue Tuggerah Business Park Tuggerah, NSW 2259, Australia

+61 (0) 2 4350 4600

+61 (0) 2 4350 4700 fax 2009 Belkin International, Inc All rights reserved All trade names are registered trademarks of respective manufacturers listed Apple, AirPort, Mac, and Mac OS, are trademarks of Apple Inc, registered in the US and other countries Windows, Windows Vista, NT, and Microsoft are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries