FCC ID: 2AD99B006D IP Video Door Station

Page 2-16 Installation Manual IP Video Door Station D21x Series Seite 17-32 Installationsanleitung IP Video Trstation D21x Serie Page 33-48 Manuel dinstallation Interphone vido IP Srie D21x Pgina 49-64 Manual de Instalacin Videoportero IP Serie D21x Pagina 65-80 Istruzioni per linstallazione Videocitofono IP Serie D21x IP Video Door Station D21x Rev. 1.7 VERSION 3.0 MIN. HW 1.75 INSTALLATION MANUAL Read these instructions carefully before starting to use any components. Keep the manual so you can refer to it at a later date if required. If you hand over the device to other persons for use, please hand over the operating manual as well. You can always find the most up-to-date version of the installation manual on www.doorbird.com/

support To make things easier we use the term device for the product IP Video Door Station and mobile device for a smartphone or tablet. Liability Every care has been taken in the preparation of this document. Please inform Bird Home Automation GmbH of any inaccuracies or omissions. Bird Home Automation GmbH cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice. Bird Home Automation GmbH makes no warranty of any kind with regard to the content of this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Bird Home Automation GmbH shall neither be liable nor responsible for incidental or consequential damages in connection with the furnishing, performance or use of this material. This product is only to be used for its intended purpose. Equipment Modifications This equipment must be installed and used in strict accordance with the instructions given in the user documentation. This equipment contains no compo-

nents that require service by the user. Unauthorized equipment changes or modifications will invalidate all applicable regulatory certifications and approvals. Symbols used Danger: Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Warning: Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Caution: Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE Notice: Indicates a situation which, if not avoided, could result in damage to property. Important: Indicates significant information which is essential for the product to function correctly. Note: Indicates useful information which helps in getting the most out of the product. Hazard information WARNING Mounting, installation and servicing work on electrical devices may only be performed by a qualified eletrician. Failure to observe this regulation could result in the risk of serious damage to health or fatal injury due to electric shocks. Devices with 110-240 V connection: The device may only be connected to an easily accessible power socket outlet. The mains adapter must be pulled out if a hazard occurs. For power supply, only use the original plug-

in mains adapter delivered with the device, separately available DIN rail power supplies or a recommended PoE-Switch/PoE-Injector as specified in this manual. Because of electrostatic charging, direct contact with the circuit board can result in destruction of the device. Direct contact with the circuit board must therefore be avoided at any time. Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard. Do not use the device if there are signs of damage to the housing, control elements or connecting sockets, for example, or if it demonstrates a malfunction. If you have any doubts, please have the device checked by an authorized expert. Do not open the device. This voids the warranty of the device. The device does not contain any parts that can be maintained by the user. In the event of an error, please have the device checked by an authorized expert. For safety, approval and licensing reasons

(CE/FCC/IC etc.), unauthorized change and/or modification of the device is not permitted. The device is not a toy: do not allow babies and children to play with it. To avoid the danger of suffocation, keep any packing materials away from babies and children. Plastic films/bags, pieces of polystyrene, etc. are not a toy and can be dangerous in the hands of a child. Discard any packing materials immediately after removing the product. Do not reuse packing materials. Always lay cables in such a way that they do not become a risk to people and domestic animals. Voltage is applied to parts within the equipment. Do not touch any parts that are 2 WARNING not associated with the installation, wiring, or connection. Electric shock could result. On devices which are not marked as weather-

proof: Keep the device away from water or any other liquid. Do not install or make any wire terminations while power supply is plugged in. It can cause eletric shock or damage to the device. Before turning on power, make sure wires are not crossed or shorted. If not, fire or eletric shock could result. High voltage may be present internally. Do not open the device. Electric shock could result. The device is not of explosion-proof. Do not install or use near gases or flammable materials. Fire or explosion could result. Do not install two power supplies in parallel to a single input. Fire or damage to the device could result. Be sure to connect a single power supply to the device. Do not connect any terminal on the device to an AC power line. Fire or electric shock could result. Keep AC cord from being marred or crushed. If the AC cord is fractured, fire or electric shock could result. Do not plug or unplug with wet hands. Electric shock could result. Do not put any metal or flammable material into the device. Fire, electric shock, or device trouble could result. Existing wiring may contain high voltage AC electricity. Damage to the device or electric shock could result. Wiring and installation must be done by a qualified eletrician. When mounting the device on a wall or ceiling, install the device in a convenient location, but not where it could be jarred or bumped. Injury could result. On devices with ground terminals, connect to an earth ground. Otherwise fire or malfunction could result. On devices with plastic or real glass, do not put high pressure on the glass. If fractured, injury could result. On devices with LCD, if LCD is punctured, do not allow contact with the liquid crystal inside. Injury could result. If necessary, gargle your mouth and clean your eyes or skin with clear water for at least 15 minutes and consult your doctor. Do not put anything on the device or cover the device with cloth, silicone, glue, coating, separate covering etc. Fire or device issues could result. Do not install the device in any of the following locations. Fire, electric shock, or device trouble could result. Places under direct sunlight or places near heating equipment that varies in temperature. Places subject to dust, oil, chemicals, hydrogen sulfide (hot spring). Places subject to moisture and humidity extremes, such as bathrooms, cellars, greenhouses, etc. Places where the temperature is very low, such as inside a refrigerated area or in front of an air conditioner. Places subject to steam or smoke (e.g. near heating or cooking surfaces). Where noise generating devices such as dimmer switches or inverter electrical appliances are closeby. Locations subject to frequent vibration or impact. On devices with intercom, be sure to perform a call test with low audio volume on both intercom devices. A sudden call etc. may arrive causing for example damage to your ear. If the device does not operate properly, unplug the power supply. All devices which are not marked as weather-

proof are designed for indoor use only. Do not use outdoor. On devices which are marked weather-proof:

Do not spray with high-pressure water. Device issues could result. We do not assume any liability for damage to property or personal injury caused by improper use or the failure to observe the hazard information. In such cases, any claim under warranty ceases. For consequential damages, we assume no liability!

Safety instructions NOTICE The device shall be used in compliance with local laws and regulations. Store the device in a dry and ventilated environment. Avoid exposing the device to shocks or heavy pressure. Do not install the device on unstable brackets, surfaces or walls. Make sure the material is strong enough to support the weight of the device. Use only applicable tools when installing the device. Using excessive force with tools could 3 ENGLISH Keep the device more than 1 m (3.3) away from microwave, radio, TV, wireless router and any other wireless devices. NOTICE When transporting the device, use the original packaging or equivalent to prevent damage to the device. Transportation devices; failures due to Internet providers and cellular network providers; failures such as disconnected lines and other losses in communication, which makes it impossible to provide this service as well as in any way delay this service due to any other causes outside of our responsibility; or if an error or missing data occurs during transmission. Warranty Information For information about the device warranty, see www.doorbird.com/warranty Information on disposal for users of waste electrical & electronic equipment (private household) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted an a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. Information on disposal in other countries outside the European Union This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal. cause damage to the device. Do not use chemicals, caustic agents, or aerosol cleaners. Use a clean dry cloth for cleaning. Use only accessories that comply with technical specification of the device. These can be provided by Bird Home Automation GmbH. Use only spare parts provided by or recommended by Bird Home Automation GmbH. Do not attempt to repair the device by yourself. Contact Bird Home Automation GmbH for service matters. On devices with intercom or built-in speaker or built-in microphone or signal transmission functions, keep the wires more than 30 cm

(12) away from AC 100-240 V wiring. AC induced noise and/or device malfunction could result. Install the device in an area that will be accessible for future inspections, repairs and maintenance. If the device is used close to a cellular phone, the device may malfunction. The device can be damaged if dropped. Handle with care. The device turns inoperative during power failure. On devices with intercom or built-in speaker or built-in microphone, in areas where cellular or Radio / TV broadcasting station antennas are closeby, the device may be affected by radio frequency interference. On devices with LCD screen, it must be noted in advance that the LCD panel, though manufactured with very high precision techniques, inevitably will have a very small portion of its picture elements always lit or not lit at all. This is not considered a device malfunction. On devices with intercom, due to the environmental sound around the device, it may hinder smooth communication, but this is not a malfunction. On devices with Username/Password, the Username/Password to access the device is the customers responsibility. Make sure to use a password that cannot be easily guessed by a third party. We recommend that you change the Password on a regular basis. We will, under no circumstances, be liable for damage that occurs due to failures in power supply, network equipment or terminal 4 DEVICE EXAMPLE WITH 1 CALL BUTTON 1) HDTV Video 2) Light Sensor For night vision mode 3) Security screws 4) Motion Sensor call button with 5) Illuminated nameplate The illumination is also acting as Diagnostic LED(s). 6) Night Vision LEDs 7) Microphone 8) Loudspeaker 9) RFID Reader 1) Main Electrical Unit 2) Yellow cable for call button Connected to button with nameplate the illuminated call 3) Red cable for Module Port 1(unused) 4) Green cable for Module Port 2

(unused) 5) Screw connection terminal 6) LAN/PoE jack 7) Nylon cord To secure the front panel during assembly DEVICE EXAMPLE WITH 2 AND MORE CALL BUTTONS 1) HDTV Video 2) Light Sensor For night vision mode 3) Security screws 4) Motion Sensor 5) Illuminated call buttons with nameplate The illumination is also acting as Diagnostic LED(s). 6) Night Vision LEDs 7) Microphone 8) Loudspeaker 9) RFID Reader Front Inside Front 1 2 3 4 5 1 2 3 4 5 Inside 1) Main Electrical Unit To fix the Multi Tenant Module temporary on the 2) Velcro tape 1 Main Electrical Unit during assembly To fix the Multi Tenant 9) Velcro tape 2 Module permanently on the backbox 3) Yellow cable for call button (unused) 6) Screw connection terminal 4) Red cable for Module Port 1 Connected to Multi Tenant Module 5) Green cable for Module Port 2

(unused) 7) LAN/PoE jack 8) Nylon cord To secure the front panel during assembly 10) DoorBird Multi Tenant Module MTM18A 10 5 6 7 8 9 1 2 3 4 5 6 7 6 7 8 9 1 2 3 4 5 6 7 8 9 ENGLISH DEVICE EXAMPLE WITH DISPLAY MODULE AND KEYPAD MODULE DEVICE EXAMPLE WITH INFO MODULE AND KEYPAD MODULE 9 10 9 10 11 1) Night Vision LEDs 9) Display Module 2) HDTV Video 3) Microphone 4) Light Sensor For night-vision mode 10) Keypad Module The illumination is also acting as Diagnostic LED(s) 5) Security screws 6) Loudspeaker 7) RFID Reader 8) Motion Sensor 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1) Main Electrical Unit 2) Yellow cable for call button (unused) 3) Red cable for Module Port 1 Connected to the Display Module 4) Green cable for Module Port 2 Connected to the Display Module 5) Screw connection terminal 6) LAN/PoE jack 7) Nylon cord To secure the front panel during assembly 1) Night Vision LEDs 2) HDTV Video 3) Microphone 4) Light Sensor For night-vision mode 5) Security screws 6) Loudspeaker 7) RFID Reader 8) Motion Sensor 9) Info Module 10) Keypad Module The illumination is also acting as Diagnostic LED(s) call button with 11) Illuminated nameplate The illumination is also acting as Diagnostic LED(s). 1) Main Electrical Unit 2) Yellow cable for call button Connected to button with nameplate the illuminated call 3) Red cable for Module Port 1 Connected to the Keypad Module 4) Green cable for Module Port 2 Connected to the Info Module 5) Screw connection terminal 6) LAN/PoE jack 7) Nylon cord To secure the front panel during assembly 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Front Inside Front Inside 6 DEVICE EXAMPLE WITH DISPLAY MODULE AND KEYPAD MODULE DEVICE EXAMPLE WITH FINGERPRINT READER MODULE Front 1 2 3 4 5 Inside 6 7 8 9 10 1 2 3 4 5 6 7 1) HDTV Video 2) Light Sensor For night vision mode 3) Security screws 4) Motion Sensor call button with 5) Illuminated nameplate The illumination is also acting as Diagnostic LED(s). 6) Night Vision LEDs 7) Microphone 8) Loudspeaker 9) RFID Reader 10) Fingerprint Reader 1) Main Electrical Unit 2) Yellow cable for call button Connected to button with nameplate the illuminated call 3) Red cable for Module Port 1 Connected to the fingerprint reader module 4) Green cable for Module Port 2

(unused) 5) Screw connection terminal 6) LAN/PoE jack 7) Nylon cord To secure the front panel during assembly Some door stations of the D21x series have an optional additional Accessibility Module including status display with three pictograms [calling, speaking, door opening], door opening acoustics and hearing loop. The module complies with DIN 18040 (Construction of accessible buildings) when installed properly. The power supply for the hearing loop must be provided by a separate power supply unit (15 - 48 VDC, 1 A) due to the high power consumption. your network components are no older than two years, have been manufactured by a well-known manufactu-

rer, and have the latest firmware installed. Should these requirements not be fulfilled, it may occur, for example that the performance of audio and video is poor or push notifications are delayed or do not arrive on your smartphone or tablet at all. Requirements:

High-speed Internet (via landline): DSL, cable or optical fibre Network: Ethernet, with DHCP VIDEOS Need help with the installation? Be sure to watch our installation videos which can be found on http://www.doorbird.com/support Each individual step of the installation is clearly documented in the videos. INSTALLATION All the steps below should be carried out carefully by a competent adult, taking into consideration any applicable safety regulations. Please contact us directly or seek the advice of a competent specialist. Please ensure that all wires used for the installation are undamaged along their entire length and approved for this type of use. Network speed and network components Please ensure that the upload speed of your Internet connection is at least 0.5 Mbps. You can also carry out a speed test at any time via the DoorBird App. The user experience is only as good as your network speed, network stability and quality of your network com-

ponents, such as your Internet Router and WiFi access points or WiFi repeaters. Please also make sure that 7 ENGLISH SWITCHING OFF POWER Switch off the power to all wires leading to the assembly location, i.e. the door chime, electric door opener, power supply unit for the video door station etc. 2 DISMANTLING THE EXISTING DOORBELL Should there already be a doorbell or door station on the exterior wall of the house, please dismantle it. 1 3 DETERMINING THE ASSEMBLY LOCATION The device uses an ultra wide-angle hemispheric lens so that even when the person is a minimum distance of 50 cm (19.68 in) away from the device, a low installation height is sufficient. The lens is therefore not mechanically adjustable. The camera lens should be located at an altitude of at least 145 cm (57 in). You may check this prior to the final mounting. When choosing the assembly location, consider the lighting conditions. Avoid direct sunlight, direct backlight and reflective surfaces. N OTI C E NOTICE Do not expose the device to direct sunlight. The housing temperature can exceed the maximum allowed temperature limit. This can result in damage of electric and mechanic components of the device and injuries especially when touching exterior parts of the device. White and bright silver-colored front plates absorb less sunlight than dark ones. An image sensor must not be exposed to direct sunlight for an extended period of time. Direct sunlight will blind the camera and may permanently bleach the small color filters on the image sensor chip. Any defects caused by direct sunlight are not covered by warranty. The network cable between the device and the PoE-Switch/PoE-Injector/Internet Router can have a maximum length of 80 meters/262 feet (IEEE 802.3). If you have only two wires available at the assembly location, you may use of the DoorBird 2-Wire Ethernet PoE Converter A1071, sold separately. It allows you to transfer network data (Ethernet) and power (PoE) with a simple two-wire cable over long distances. For example; existing buildings with a simple two-wire bell wire can be equipped with network technology without having to retrofit any network cables. 4 REMOVING THE FRONT PANEL Remove the front panel carefully using the screw driver provided with the device from the mounting housing

(backbox). 1 c m 1.) Turn out the security screws for 1 cm 8 2.) Pull down the front panel. 3.) Pull the front panel towards you. 5 ASSEMBLING THE MOUNTING HOUSING Remove the front panel carefully using the screw driver provided with the device from the mounting housing (backbox). You can find detailed drawings and measurements of the device in the corresponding datasheet. If you must drill holes in a wall, insert screws into a wall or lever up a wall, ensure that no cables or mains (gas, water, etc.) are to be found in the wall. Mounting the surface-mounted housing Rubber seal for cable entry Cover for unused openings Place the rubber seal for the cable entry on the mounting opening. Pierce through the middle of the rubber seal using a screwdriver. Feed all cables and wires that you want to connect to the device through the rubber seal. Important note for cavity mounting (e.g. in pedestals and mailboxes):

To protect the electronic units, please ensure that the technical components are protected against dripping and running water caused by condensate or entering the mounting space through openings. To protect the electronic units, ensure that the mounting space inside is not accumulating water. 6 POWER SUPPLY OPTIONS Sufficient air circulation must be ensured, as well as unobstructed drainage of water at the base of the installation. Failure to do so will result in warranty being declined. The device can be powered using the DoorBird power-supply unit (mains adaptor) (Option 1) or via PoE

(Power over Ethernet) using a network cable (Option 2). The device can be alternatively also be supplied with power using a DIN-rail power supply unit that you can obtain direclty from us. The device does not use battery power. OPTION 1 Power supply and network connection using PoE (Power over Ethernet) To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-Injector (e.g. DoorBird Gigabit PoE Injector A1093) in accordance with the PoE standard IEEE 802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a Cat.5 cable or better are to be used. Make sure to use a high-quality Cat.5 network cable or better and with proper shielding (Screened Foiled Twisted Pair (S/FTP or SFTP)) whereby the shield is connected to the outer metal shield of the RJ45 plug (8P8C). If you use PoE as a source of power the four wires for PoE then simultaneously form the data link. The device wont start if your PoE-Switch/PoE-Injector does not support the PoE Standard IEEE 802.3af Mode A

(see Diagnostic-LED and Diagnostic-Sounds). 1. Disconnect the PoE-Switch or PoE-Injector from the power grid. 2. Run the network cable to the installation location of the device. 9 ENGLISH OPTION 2 Power supply using the power supply unit (mains adaptor) Power supplies can be purchased from us, but we generally recommend using only Power over Ethernet (PoE) as the power supply. N OT I C E Do not plug the power supply unit into the wall socket yet. Only use the original DoorBird power supply unit or a DIN-rail power supply unit that you can obtain from us separately, since this has been specially stabilized electrically and is equipped with an integrated audio inter ference reduction device. Other power supply units may destroy the device or cause poor transmission quality. The warranty expires automatically if you use a different power supply unit. 7 CONNECTING THE DEVICE It is possible to connect the cables and wires to the device conveniently and safely via labelled connection ports. You can connect all necessary cables and wires to the device now. Please remove any cables and wires from the connection ports of the device that you do not need. Remove about 5 mm of insulation material at the end of the wires that you would like to connect to the green screw connection terminal of the device. Handle the front panel with care. The surface of the front panel could be scratched or otherwise damaged if handled without care. N OT I C E Please take care when connecting the cables and wires. Connecting the cables and wires the wrong way may damage the device. Wires without insolation material must not protrude out of the green screw connection terminal, it may lead to electrical short and damage the device. N OT I C E The yellow, green, and red cables that lead out from the side of the Main Electrical Unit must only be used to connect components certified by Bird Home Automation. You can use the nylon cord to temporary fix the front panel to the mounting housing (backbox) while connecting the cables and wires to the device. DOORBIRD D21x REL1 REL2 EXT 15VDC Only related for devices with call button(s) Each Call Button is equipped with one jack. 4 Pin 10 PORT DESCRIPTION LAN/POE RJ45 jack to connect the Network coming from the Internet Router/PoE-Switch/PoE-

Injector. NOTICE Do not power the device simultaneously via the power supply from the power supply unit (mains adaptor) and the power supply via PoE. REL1, REL1 Bi-stable latching relay #1, max. 24 V DC/AC, 1 Ampere. Security feature: The relay keeps its state even in the case of loss of power. You can configure the default state of the relay

(open/close) via the DoorBird App. These ports can be used to connect e.g. an electric door opener. The device does not supply power to the connected device. The power supply for the electric door opener must be installed separately. REL1 REL1 When wiring an electric door opener directly to a door station, there is a risk that the electric door opener could be tampered by unauthorized third parties (e. g. by breaking the door station and short-circuiting the wiring of the door opener). Therefore, we generally recommend the use of a remote safety relay mounted indoors (e. g. DoorBird I/O Door Controller A1081) for wiring an electric door opener for a more secure installation in your home. REL2, REL2 Bi-stable latching relay #2, max. 24 V DC/AC, 1 Ampere. Security feature: The relay keeps its state even in the case of loss of power. You can configure the default state of the relay

(open/close) via the DoorBird App. These ports can be used to connect e.g. an electric door opener. The device does not supply power to the connected device. The power supply for the electric door opener must be installed separately. REL2 REL2 When wiring an electric door opener directly to a door station, there is a risk that the electric door opener could be tampered by unauthorized third parties (e. g. by breaking the door station and short-circuiting the wiring of the door opener). Therefore, we generally recommend the use of a remote safety relay mounted indoors (e. g. DoorBird I/O Door Controller A1081) for wiring an electric door opener for a more secure installation in your home. BELL, BELL EXT, EXT EXT EXT NOT IC E Reserved Do not use!

Door opener button, max. 0 V DC/AC, 0 Ampere. These ports can be used to connect e.g. a door opener button inside the home. It will trigger the first bi-stable latching relay of the device (REL1, REL1). NOT IC E Please make sure to add no voltage on these ports. Extra voltage may destroy the device immediately. 15 VDC -

15 V DC Power supply input, negative pole (-). Please connect the black wire of the DoorBird power supply unit (mains adaptor) here, if you do not power the device using PoE. We only recommend PoE. NOT IC E Do not power the device simultaneously via the power supply from the power supply unit (mains adaptor) and the power supply via PoE. 15 VDC +

15 V DC Power supply input, positive pole (+). Please connect the red wire of the DoorBird power supply unit (mains adaptor) here, if you do not power the device using PoE. We only recommend PoE. NOTICE Do not power the device simultaneously via the power supply from the power supply unit (mains adaptor) and the power supply via PoE. Only related for devices with call button(s):

4 PIN (SWITCH) Use the yellow cable to connect the button to the IP Video Door Station. NOTICE Please take care when connecting the cables and wires. Connecting the cables and wires the wrong way may damage the device. Wires without insolation material must not protrude out of the green screw connection terminal, it may lead to electrical short and damage the device. 11 ENGLISH NOTICE The yellow, green, and red cables that lead out from the side of the Main Electrical Unit must only be used to connect components certified by Bird Home Automation. 8 ASSEMBLING THE FRONT PANEL Assemble the front panel of the device to the mounting housing (backbox) of the device. 2.) Push the front panel up. 3.) Insert the security screws. 1.) Pull the front panel into the mounting housing

(backbox) 9 ACTIVATING THE DEVICE Switch on the power leading to the assembly location again. If you use PoE, make sure to switch on power of the PoE-Switch or PoE-Injector you have connected the device to. NOT I C E Do not power the device simultaneously via the power supply from the power supply unit (mains adaptor) and the power supply via PoE. You can see if the device is powered by checking the Diagnostic-LED, which lights up after about 30 to 60 seconds after the power is connected. The device is ready for operation (booting up process, any software updates, etc.) once it has emitted a short diagnosis sound from the integrated loudspeaker. This may last for up to 5 minutes. If the Diagnostic LED does not light up, please check the power supply. Please also check whether you have used a wall-plug power supply and not PoE and whether you have connected the positive pole and negative pole to the device correctly. 10 DOWNLOADING AND INSTALLING THE APP Download the DoorBird App by Bird Home Automation onto your mobile device from the Apple App Store or Google Play Store. You can always find the most up-to-date version of the App manual on www.doorbird.com/support Go to DoorBird App Settings > Add device and click on the QR code icon in the User field. Scan the user QR code found on the Passaporto digitale provided with the device. If you have problems adding the device to the App, please check if the device is online

(www.doorbird.com/checkonline). If the device is not online, please check the network connection and the power supply of the device. 12 DIAGNOSTIC-LED Engraving Service You can see if the device is powered by checking the Diagnostic-LED, which lights up after about 30 to 60 seconds after the power is connected. DIAGNOSTIC-SOUNDS After around one to five minutes, the device emits brief diagnostic sounds after it has been connected to the power grid. MOTION SENSOR The device has a built-in Motion Sensor with 4D Technology. You can use it for numerous applications, e. g. to send an alarm to a mobile device or to switch a relay to turn on an outdoor light. RFID READER The built-in RFID reader can be used for many applications, e.g. to open/lock doors or arming/

disarming your alarm system. For security reasons, the RFID reader has a very short range (0 - 3 cm, 0 - 1.18 in), so you must place the compatible RFID tag (key fob) very close to the RFID reader. You can configure the RFID reader using the DoorBird App. Engraving service for a modern and clean appearance: www.doorbird.com/engraving Please follow STEP 1 to switch off power. We recommend to use a thin slot screwdriver to remove the cover of the nameplate. We recommend to use white paper for the label which does not absorb moisture. CHANGING THE LABEL OF THE INFO MODULE Applies only to devices with Info Module. Please follow STEP 1 to switch off power and STEP 2 to open the device. You can then change the labeling of the Info Module in the inside. We recommend to use white paper for the label which does not absorb moisture. CONNECTING CALL BUTTONS TO THE MULTI TENANT MODULE The RFID reader works only on short distance, for security reasons. Applies only to devices with 2 and more illuminated call buttons with nameplate. API The device features a well documented API for third-party integration. For information, terms and conditions see www.doorbird.com/api Connect only call buttons to the Multi Tenant Module

(e.g. Multi Tenant Module MTM18A) certified by Bird Home Automation. DOORBIRD CONNECT 18 17 16 15 14 13 1 = 1. call button jack 18 = 18. call button jack The device features many options to integrate it into third-party applications. For information, terms and conditions see www.doorbird.com/connect CHANGING THE LABEL OF A CALL BUTTON NAMEPLATE Applies only to devices with 1 and more illuminated call buttons with nameplate. 12 11 10 9 8 7 6 5 4 3 2 1 13 ENGLISH MAINTENANCE FOR DOORBIRD PRODUCTS Cleaning and maintenance instructions All DoorBird door stations are made of high-quality materials and are designed for a durable lifetime. Since door stations are usually installed in unprotected outdoor areas, they are exposed to adverse weather conditions and aggressive substances, especially close to frequently used roads, in coastal and industrial areas. Therefore please consider the following care instructions. Unfortunately, we cannot accept any liability for damage if these instructions are not being observed. Aggressive dirt such as bird droppings should be removed as quickly as possible. N OTI C E Never use abrasive detergents such as steel wool or scouring milk!

Warm water is usually sufficient, if necessary with a little detergent, a soft cloth or brush. Plastic parts

(camera or name tags) must not be treated with metal care products. Remove all residues of cleaning agents or lubricants to avoid stains or discolouration after the maintenance. Stainless Steel Only high-quality German stainless steel is used for all available DoorBird door stations. However, high-quality stainless steel can also rust, as approx. 70% of stainless steel is made of iron. Rust resistance is only achieved by a protective layer (also called passive layer), which covers the iron like a skin. This protective layer consists essentially of chromium and other precious metals. Iron particles, grinding dust and chips deposited on stainless steel can lead to corrosion (rust film). These iron particles can be found everywhere, but especially in coastal and industrial areas and close to frequently used roads. Please remove ferrous deposits immediately, as they will attack your door station and lead to real rust if not removed. To remove rust, simply wipe off the dust; in addition, a care product is recommended, e.g. WD 40, available e.g. at Amazon for less than 5.00. Simply apply in a thin layer and rub in. The same applies if rust appears on the engravings on the stainless steel surface. Cement or lime splashes should be carefully removed as soon as possible with a wooden spatula before hardening. cloth and rub dry to avoid lime traces. Lime residues can be avoided by using demineralised water. Stainless steel PVD coated PVD coated, chrome-plated or gold-plated surfaces are recommended to be cleaned with a grease-

dissolving detergent and clear water or with a clean and dust-free microfibre cloth. For high-gloss surfaces, use a scratch-free cloth (e.g. cleaning cloth for glasses, furniture polishing cloth, etc.). Lacquered surfaces Clean painted surfaces and lettering with a soft, scratch-free cloth moistened with a mild soap solution

(e.g. cleaning cloth for glasses, furniture polishing cloth, etc.). To prevent stains or discolouration, the detergents should be wiped off without leaving any residue. Be particularly careful with lettering in order not to damage the film or the print. TECHNICAL SPECIFICATIONS Info Module*

3.5, illuminated GENERAL Power supply Display Module*

Keypad Module*

Accessibility module*

15 V DC (max. 15 W) or Power over Ethernet (PoE 802.3af Mode-A) 3.5 LCD (no touch function), illuminated, for the display of a 2-line free text and the name directory (max. 200 entries) 16 keys, illuminated, configurable via App, e.g. Individual PIN codes Individual events (e.g. switch a relay, push notification, SIP call

[audio/video], HTTP(s) request) Individual schedules Up to 200 PIN codes manageable Separate power supply:

15 - 48 VDC, 1 A Status display with three pictograms [calling, speaking, door opening], door opening acoustics and hearing loop Approval according to DIN 18040 RJ45, for LAN/PoE Bistable latching relay #1, max. 24 V DC/AC, 1 A, e.g. for electric door opener Bistable latching relay #2, max. 24 V DC/AC, 1 A, e.g. for electric door opener External input for external door opener button 15 V DC input (+, -), max. 15 W Relays can be expanded /

detached with DoorBird I/O Door Controller The following cleaning detergents are not to be used as they reduce corrosion resistance:

Connectors acid products containing chloride and hydrochloric Bleach (in case of accidental use, rinse thoroughly with water) Silver polish After the cleaning with clear water wipe with damp Weather-proof Yes, IP65 14 Approvals Operating conditions Scope of delivery IP65, CE, FCC, IC, RoHS, IK08, REACH, IEC/EN 62368, IEC/EN 62471

-25 to +55C / -13 to 131F Humidity 10 to 85 % RH

(non-condensing) 1x Main Electrical Unit 1x Front panel*

(110 - 240 V AC to 15 V DC) 1x RFID key fob 1x Screwdriver 1x Quickstart guide with Passaporto digitale 1x Installation manual 1x Small parts Warranty see www.doorbird.com/warranty CURRENT SYSTEM REQUIREMENTS System requirements Recommended installation height VIDEO Camera Lens Night-vision AUDIO Audio components NETWORK Ethernet Supported protocols Mobile device: Newest iOS on iPhone/iPad, newest Android on Smartphone/Tablet Internet: High-Speed Landline Broadband Internet connection, DSL, cable or fiber optic, no socks or proxy server Network: Ethernet Network, with DHCP Camera lens should be at a min. height of 145 cm (57 in). Before the installation please determine your optimal installation height. HDTV 720p, dynamic (VGA HDTV) High-end ultra wide-angle hemispheric lens 180 (D), 140

(H), 100 (V), straightened, IR-

capable Yes, light sensor, automatic IR-cut filter, 12 Infrared LEDs (850 nm) RJ45 jack, PoE 802.3af Mode-A, 10/100 Base-T HTTP, HTTPS, SSL/TLS, Bonjour, DNS, RTSP, RTP, TCP, UDP, RTCP, ICMP, DHCP, ARP, SIP, DTMF (RTP

[RFC-2833], SIP INFO [RFC-2976]), STM

* Only contained in certain models or configurations Errors and omissions excepted. MOTION SENSOR Type Active Detection angle 54 (H), 70 (V) Range Technology Configuration RFID Type Standard Compatible Transponder 1 - 10 m (3.3 - 32.9 ft), depends on environment, configurable in 1 m

(3.3 ft) steps. If a Display Module is connected to the Main Electrical Unit, the range is limited to 1 m (3.3 ft). 4D. Based on multiple integrated sensors and algorithms, e.g. Radio Frequency Energy (RFE) Via App, e.g. Range (1 - 10 m / 3.3 - 32.9 ft) Movement direction (coming, leaving, both) Individual events (e.g. switch a relay, push notification, SIP call

[audio/video], HTTP(s) notification) Individual schedules Active Reader Passive Tag (ARPT) system ISO/IEC 18000-2:2009 Part 2, EM4100, EM4102 RFID key fobs, sold separately, see www.doorbird.com/buy Up to 200 tags manageable Via App, e.g. Tag (add, delete) Individual events (e.g. switch a relay, SIP call [audio/video], HTTP(s) notification) Individual schedules RFID history available for 60 minutes in the app Frequency 125 KHz Range 0 - 3 cm, depends on environment Antenna Internal INTEGRATED WIRELESS MODULES RFID Sensor 125 KHz 24 GHz, can be disabled THIRD-PARTY INTEGRATION (DOORBIRD CONNECT) Partnerintegrations see www.doorbird.com/connect API see www.doorbird.com/api Simultaneous video streams One, for event-based and continuous recording OPTIONAL ACCESSORIES Sold separately see www.doorbird.com/buy 15 Speaker and microphone, noise reduction and echo cancellation

(ANR, AEC) Configuration Audio streaming Two-way, full duplex ENGLISH LEGAL NOTES General remarks 1. DoorBird is a registered trademark of Bird Home Automation GmbH. 2. Apple, the Apple logo, Mac, Mac OS, Macintosh, iPad, Multi-Touch, iOS, iPhone and iPod touch are trademarks of Apple Inc. 3. Google, Android and Google Play are trademarks of Google, Inc. 4. The Bluetooth word mark and logos are registered trademarks of Bluetooth SIG, Inc. 5. All other company and product names may be trademarks of the respective companies with which they are associated. 6. We reserve the right to make changes to our products in the interests of technical advancement. The products shown may also look different from the products supplied based on ongoing enhancement. 7. Reproducing or using texts, illustrations and photos from this instruction manual in any media even if only in the form of excerpts shall only be permitted with our express written consent. 8. The design of this manual is subject to copyright protection. We do not accept any liability for any errors or any erroneous content or printing errors (even in the case of technical specifications or within graphics and technical sketches). 9. Our products are in compliance with all technical guidelines, electrical and telecommunications regulations applicable in Germany, the EU and the USA. 10. Our products and also the components contained therein

(ICs, software, etc.) may only be used for civilian non-military purposes. Data privacy and data security 1. For maximum security, the device uses the same encryption technologies as are used in online banking. For your security, no port forwarding or DynDNS is used either. 2. The data centre location for remote access over the Internet by means of an App is obligatory in the EU if the determined Internet IP-Address location of the device is within the EU. The data centre is operated in line with the most stringent security standards. 3. Video, audio and any other surveillance methods can be regulated by laws that vary from country to country. Check the laws in your local region before installing and using this device for surveillance purposes. If the device is a door-, indoor station or camera:

In many countries video and voice signal may only be transmitted once a visitor has rung the bell (data privacy, configurable in the App). Please carry out the mounting in such a way that the detection range of the camera limits the device exclusively to the immediate entrance area. The device may come with a visitor history and motion sensor. You can activate/deactivate this function if required. If necessary, indicate the presence of the device in a suitable place and in a suitable form. Please observe any relevant country-specific statutory regulations concerning the use of surveillance components and surveillance cameras applicable at the installation site. Check with the property owner and your house community if you are allowed to install and use this product. Bird Home Automation GmbH cannot be held responsible for any miss-use or miss-configuration of this product, including the unauthorized opening of a door. Bird Home Automation cannot be held responsible for damages caused by improper existing installations or improper installation. Software and operating systems updates (so-called firmware updates) are generally automatically installed on the products of Bird Home Automation GmbH via Internet, if technically possible. Automatic firmware updates keep the products software up to date so that they always work reliably, safely and efficiently. Through further development, features can be added, extended or slightly changed. Major changes or limitations to existing features will generally occur if Bird Home Automation GmbH deems it necessary

(e.g. for data protection, data security or stability reasons, or to keep them up to date). When a firmware update is available, Bird Home Automation GmbHs servers generally automatically distribute it to all compatible products connected to the Internet or Bird Home 16 Automation GmbHs servers. This process is gradual and can take several weeks. As soon as a product receives a firmware update, the system will be installed and will restart by itself. Installed firmware updates cannot be undone. Since the products and software of Bird Home Automation GmbH are not explicitly customer-specific products, a customer cannot deny an automatic update if the product is connected to the Internet or to the Bird Home Automation GmbHs server. Publisher Bird Home Automation GmbH Uhlandstrae 165 10719 Berlin Germany Web: www.doorbird.com Email: hello@doorbird.com It is possible that these manual still contains typographical errors or printing errors. The information in this manual will be checked regularly and corrections will be made in the next version. We accept no liability for errors of a technical or printing nature and their consequences. IC Caution:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF exposure statement:

The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS

(RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes:

(1) Cet appareil ne doit pas causer d'interfrences.

(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement indsirable de l'appareil. Tout changement ou modification non expressment approuv par la partie responsable de la conformit pourrait annuler l'autorit de l'utilisateur utiliser l'quipement. Dclaration d'exposition RF:

L'quipement est conforme la limite d'exposition aux radiations de la IC tablie pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. IC20208-B006D FCC Caution:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:?(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. FCC ID: 2AD99B006D www.doorbird.com

Page 1 of 1 FCC ID: 2AD99B006D IC: 20208-B006D LABEL AND LOCATION IP Video Door Station Model: D21x Rev. 1.7 FCC ID: 2AD99B006D IC: 20208-B006D

(Size: L4cm x 2cm) Label Location Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2022-7-28>

Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID 2AD99B006D Model name D21x Rev. 1.7 For the product stated above, we request confidential;

that the following information be held Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos Users Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our information that could be of benefit to our competitors. trade secrets and proprietary The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title Sascha Keller/CEO Company:

Address:

Phone:

Fax:

E-Mail:

Bird Home Automation GmbH Uhlandstr. 165, 10719 Berlin, Germany

+4930609844545

certlab-support@doorbird.com

Bird Home Automation GmbH Uhlandstr. 165, 10719 Berlin, Germany Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2022-7-28 To whom it may concern:

We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AD99B006D including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title Sascha Keller/CEO Company:

Address:

Phone:

Fax:

E-Mail:

Bird Home Automation GmbH Uhlandstr. 165, 10719 Berlin, Germany

+4930609844545

certlab-support@doorbird.com