FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in mobile/ fixed (min 20cm) exposure condition without restriction. LOCATION OF CONTR0LS MAN UNIT:
Front:
1. Remote Receiver 2. LED Display 3. VOLUME Control Knob
(Disc Tray Open-Close)/(Standby) Button 4. 5. I (Skip backward/Radio program down) Button 6. I (Skip forward/Radio program up) Button 7. AUX (In) Jack 8. CD Disc Tray 9. II/PP (Play-Pause/Radio Program Preset) Button 10. /
(Stop/Decorative Lights On-Off) Button 11. MODE Button 12. USB Port (For music playback) 6 Rear:
1. FM ANT (Antenna) 2. POWER Switch 3. DC 15V (In) Jack 4. Speaker R (right) Clips 5. Speaker L (left) Clips 7 REMOTE CONTROL:
1.
(Standby) Button 2. Numeric Buttons PROG (Program) Button 3. 4. (Fast rewind/Radio tuning down) Button 5. I (Skip backward/Radio program down) Button REP (Repeat) Button 6. 7. II/PP (Play-Pause/Radio Program Preset) Button 8.
(Disc Tray Open/Close) Button 9. 5+ Button 10. MODE Button 11. (Stop) Button
(Mute) Button 12. 13. (Fast forward/Radio tuning up) Button 14. VOL + (Volume Up ) Button 15. I (Skip forward/Radio program up) Button 16. VOL - (Volume Down ) Button 17. EQ (Equalizer) Button 18. Button Cell Holder 8 CONNECTION:
Connect the Speaker Connection Wires from Speaker Boxes to Speaker Out Clips on the rear of unit as illustrated below:
9 POWER SOURCE:
Main unit:
Connect the small plug from the supplied AC/DC Adaptor to the DC 15V (In) Jack on the rear of unit then plug the AC/DC Adaptor to a AC wall outlet having AC 100-240V~;
50/60Hz as illustrated below:
NOTES:
If you will not use the unit for an extended period of time, unplug the AC/DC Adaptor from wall outlet. The AC/DC Adaptor is intended to be correctly orientated in a vertical or floor mount position. 10 Remote Control:
First time use:
Remove and discard the insulation film as illustrated below:
Replacing the button cell when it is drained as follows:
Push and slide out the button cell holder as illustrated below. Replace the button cell with new CR2025 button cell with the polarity markings on the rear of the Remote Control. Close the button cell holder. Battery precautions:
Follow these Battery Precaution when using a battery in this device:
1. Use only the size and type of battery specified. 2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. A reversed battery may cause damage to the device. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones. 4. If the batteries in the device are consumed or the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. 5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturers instructions.) 11 6. Do not dispose of battery in fire. Battery may explode or leak. 7. Clean the battery contacts and also those of the device prior to battery installation. 8. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burn in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. EFFECTIVE DISTANCE OF REMOTE CONTROL When there is an obstacle between the unit and the transmitter, the transmitter may not operate. When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong shines on the remote control of the unit, the remote operation may be unstable. 12 GENERAL OPERATION:
1. Connect the Speaker Boxes to the unit as previously instructed. OPERATION:
2. 3. Connect the unit to AC power as previously instructed. Slide the POWER Switch to ON position to power on the unit to standby mode. "O"
will appear on the display. 4. Press and hold the
(Standby) Button on the unit or press the button on the Remote Control to power on the unit from standby mode. 5. Press the MODE Button on the Unit or Remote Control repeatedly to switch to desired playback mode. The correspondent indicator will appear (or illuminate) on the display with your selection (see list below):
Playback Mode:
Indicators:
CD USB AUX (Aux/Line in) BT (Bluetooth) Radio FM Band Cd will appear on the display USb will appear on display & the indicatorUSbwill illuminate AUH will appear on the display &
the indicator AUHwill illuminate bt will appear on the display & the indicatorbtwill illuminate rAdI0will appear on the display a few seconds, then radio frequency XX.XX or XXX.XX will appear on the display 6. During playback:
Turn the VOLUME Control Knob on the unit or press the VOL (Volume) +/-
buttons on the Remote Control to adjust volume level as desired. Press the
(Mute) Button on the Remote Control to mute the sound, press again to turn the sound back on. Press the EQ (Equalizer) Button on the Remote Control to activate and set the equalizer effect as desired (see list below):
Showing on display:
Equalizer effects:
OFF ROC JA22 POP CLASS Turn off the equalizer effect Rock Jazz Pop Classic 13 7. When finished listening, press and hold the
(Standby) Button on the unit or press the button on the Remote Control to turn the unit to Standby Mode. NB: If you will not use the unit for an extended period of time, slide the POWER Switch to OFF position to power off the unit then unplug the AC/DC Adaptor from AC wall outlet. CD:
CD Playback:
1. Power on the unit as previously instructed. 2. Press the MODE Button on the Unit or Remote Control repeatedly until Cd appear on the display. 3. Press the
(Disc Tray Open/Close) Button on the unit or Remote Control to open CD tray. 4. Place a CD disc on the center of tray, with the printed side face up. 5. Press the
(Disc Tray Open/Close) Button on the unit or Remote Control to close it, play will automatically start after a few seconds. 6. During playback:
Press the II/PP Button on the unit or Remote Control to pause, press again to resume normal playback. Press the I or I buttons on the unit or Remote Control repeatedly to skip tracks. Press the or buttons on the Remote Control to fast searching the specific section then press the II/PP Button to resume normal playback. 7. To stop, press the (Stop) Button on the unit or Remote Control. Repeat Playback:
1. During playback, press the REP Button on the Remote Control once. The indicator
"
" will appear on the display. The current track will playback repeatedly. 2. During playback, press the REP Button twice. The indicator
"ALL
"
will appear on the display. All the tracks on the current disc will be played back repeatedly. 3. To cancel the repeat function, press the REP Button repeatedly until the repeat indicator
"
" disappears on the display. Programmed Playback:
Up to 20 tracks can be programmed playback as follows:
1. In CD stop playing mode, press the PROG Button on the Remote Control. P 01 will appear on the display. Indicator PROG will appear on the display and blink. 14 2. 3. 4. 5. 6. 7. Select the first specific track to be programmed by pressing the I or I buttons on the unit or Remote Control repeatedly. Press the PROG Button again to store the selected track into the memory. Repeat steps 2 and 3 until all the specific tracks stored into the memory. Press the II/PP Button on the unit or Remote Control to start program playback. To stop playback, press the Button on the unit or Remote Control. Press the II/PP Button to start program playback again. To stop and cancel the program, press the Button on the unit or Remote Control repeatedly until indicator PROG disappears on the display. BT:
BT (Bluetooth) pairing:
First time use or re-pairing the unit to a new BT Device, pair as follows:
1. 2. Power on the unit as previously instructed. Press the MODE Button on the Unit or Remote Control repeatedly until indicator bt appears on the display and blinks to enter to BT mode. 3. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen instructions from the external BT Device. When paired, the indicator bt on the display will stop blinking. 4. If pairing is complete you may now play music with your external BT Device. 5. During playback:
Press the II/PP Button on the unit or Remote Control to pause, press again to resume normal playback. Press the I or I buttons on the unit or Remote Control repeatedly to skip tracks. Notes:
When the external BT Device has searched the unit, our model number MM440 will appear on the display of external BT Device. If while pairing you are asked for a code please try "0000" or "1234". Normal operation after pairing:
1. 2. Power on the external BT Device and enter to BT playback mode. Power on the unit and enter to BT mode as previously instructed. Indicator bt will appear on the display and blink. 15 3. Wait a few seconds until the unit is automatically paired to the external BT Device. The indicator bt on the display will stop blinking. 4. After pairing is complete you may now play music with your external BT Device. FM RADIO:
1. 2. Power on the unit as previously instructed. Press the MODE Button on the Unit or Remote Control repeatedly indicator rAdI0 appear on the display to enter to Radio FM playback mode. Wait a few seconds, radio frequency XX.XX MHz will appear on the display. 3. To store the available FM stations into the unit (up to 30 stations) at first time use
(or relocate the unit to a new location):
Press the II/PP Button on the unit or Remote Control. FM frequency on the display will start running. Wait a few minutes, the unit will automatically store all the available FM stations into the memory then playback the first station. 4. 5. Press the I or I buttons on the unit or Remote Control repeatedly to select and play the stored FM station as desired. If reception is weak, press and release the or buttons on the Remote Control repeatedly to fine tune. 6. Or, press and hold the or buttons on the Remote Control until the FM radio frequency on the display start running to automatically search and play the next/previous available FM station. Antennas:
This unit has a FM wire antenna on the rear of unit, which provides adequate reception in most areas. If reception is weak, unwind and extended to its full length and/or reassemble the other direction/location to improve the reception. 16 AUX (AUX/LINE IN):
Listen from an external Audio Player such as a Cell phone, MP3 Player, Discman etc. 1. Connect one end of the Audio Connection Cable (not included) to the AUX Out/Line Out/Phone Jack on the external Audio Player. 2. Connect the other end of the cable to the AUX (Aux/Line In) Jack on the front of unit as illustrated below:
3. 4. Power on the unit as previously instructed. Press the MODE Button on the Unit or Remote Control repeatedly until AUH appear on the display. 5. Play the music on the connected Player as usual. (Make sure the volume level of the connected Audio Player is turned to high level.) 17 USB:
To play the music in external USB Device:
1. In standby mode, insert the USB Device into the USB Port on the front of unit as illustrated below:
2. 3. Power on the unit as previously instructed. Press the Mode Button on the Unit or Remote Control repeatedly until USb appear on the display to enter to USB playback mode. 4. Wait a few seconds, the unit will automatically play the first track on the USB Device. Note: If no USB Device was inserted into the USB Port. A few seconds later, the unit will turn to CD playback mode automatically. 5. During playback:
Press the II/PP Button on the unit or Remote Control to pause, press again to resume normal playback. Press the I or I buttons repeatedly to skip tracks. Press the or buttons on the Remote Control to search the specific section then press the II/PP Button to resume normal playback. 18 Use the Numeric & 5+ buttons on the Remote Control to select and plays the desired tracks. For examples:
To play the 4th track on the USB device, press the 4 Button. 0004 will appear on the display then the unit will start to play it. To play the 14th track on the USB device, press the 5+ + 5+ + 4 buttons. 0014 will appear on the display then the unit will start to play it. Notes:
Up to 64 GB USB Device the unit supports to play. Before replacing USB Device, make sure the unit had been turned to standby mode. When inserting the USB Device, make sure the direction you selected is correct. Never insert violently to avoid damaging the USB Device or the unit. You also need to download the desired music in MP3 format into the USB Device before insert into the unit. TROUBLESHOOTING:
Check the following before requesting service:
SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION AC/DC Adaptor had not Connected the AC/DC No power connected Adaptor to the unit and AC power as page 10 Volume of the unit was set to Increase the volume level minimum position by turning the VOLUME No sound or sound weak Control Knob on the unit clockwise or press the VOL + Button on the Remote Control Volume level of Rise the volume level of paired/connected device is in the paired/connected low level device 19 Volume level too high Reduce the volume level by turning the VOLUME Control Knob on the unit counterclockwise or press the VOL Button on the Remote Control Volume level of the Reduce the volume level connected/paired device too of the connected/paired high device Unit not in BT mode Press the MODE Button on the Unit or Remote Control repeatedly until indicator bt appear on the display and blink to enter to BT playback mode The external BT Device had Pair the external BT NOT paired to the unit Device to the unit as page 15-16 The external BT device too far Place the external BT from the unit device close to the unit Unit not in CD mode Press the MODE Button on the Unit or Remote Control repeatedly until Cd appear on the display Sound distortion BT not functioning CD not play CD disc incorrect install Place the CD disc on the center of tray with label side face up Radio not function Unit not in radio mode Press the MODE Button on Disc is dirty or scratched Try other discs the Unit or Remote Control repeatedly until indicator rAdI0 appear on the display 20 Radio reception not good The direction or location no Unwind and extended the good for radio reception FM wire antenna on the rear of unit to its full length and/or reassemble the other direction/location to improve the reception USB Device not function Unit is not in USB mode Press the MODE Button on the Unit or Remote Control repeatedly until USb appear on the display to enter to USB playback mode No audio files on the USB Download the desired Device music in MP3 format into the USB Device before insert into the unit GENERAL SPECIFICATTIONS:
Power Source:
Audio Power:
DC 15V, 3A, 25W per Channel (Total 50W, RMS) Impedance of Speakers:
30W, 4 per channel FM Band Converge:
87.5 108MHz BT Version:
5.0 BT Operation Distance:
Up to 32 Feet in opera area Disc Compatible:
CD; CD-R; CD-RW PACKAGE INCLUDES:
1 x Users Manual 1 x Remote Control (Uses 1 x CR2025 Button Cell, included) SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE 21