FCC ID: PKW-WPC54G-2 Instant Wireless Wireless-G Notebook Adapter

Instant Wireless Series Wireless-G Notebook Adapter Use this Guide to install the following:

WPC54G V2 User Guide FCC Caution: Any change or modification to the product not expressly approved by Linksys could void the user's authority to operate the device. FCC RF Radiation Exposure Statement To comply with the FCC and ANSI C95.1 RF exposure limits, the antenna(s) for this device must comply with the following:

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Canadian Department of Communications Industry Canada (IC) Notice This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numrique de la classe B est conforme la norme NMB-003 et CNR-210 du Canada.

"To prevent radio interference to the licensed service, this device is intended to be oper-

ated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing."

" Pour empcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit tre utilis l'intrieur et devrait tre plac loin des fentres afin de fournir un cran de blindage maximal. Si le matriel (ou son antenne d'mission) est install l'extrieur, il doit faire l'objet d'une licence. "

EC DECLARATION OF CONFORMITY (EUROPE) Linksys Group declares that the Instant Wireless Series products included in the Instant Wireless Series conform to the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC directive 89/336/EEC, and Low Voltage directive 73/23/EEC:

For 11Mpbs, 2.4 GHz devices with 100 mW radios, the following standards were applied:

ETS 300-826, 301 489-1 General EMC requirements for Radio equipment. EN 609 50 Safety ETS 300-328-2 Technical requirements for Radio equipment. Caution: This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact local Authority for procedure to follow. COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Copyright 2003 Linksys, All Rights Reserved. Instant Wireless, Linksys, and the Linksys logo are registered trademarks of Linksys Group, Inc. Microsoft, Windows, and the Windows logo are registered trade-

marks of Microsoft Corporation. All other trademarks and brand names are the proper-

ty of their respective proprietors. LIMITED WARRANTY Linksys guarantees that every Instant Wireless Wireless-G Notebook Adapter will be free from physical defects in material and workmanship for one year from the date of pur-

chase, when used within the limits set forth in the Specifications section of this User Guide. If the product proves defective during this warranty period, call Linksys Technical Support in order to obtain a Return Authorization number. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. When returning a product, mark the Return Authorization number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. All customers located outside of the United States of America and Canada shall be held responsible for shipping and handling charges. IN NO EVENT SHALL LINKSYS'S LIABILITY EXCEED THE PRICE PAID FOR THE PROD-

UCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAM-

AGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFT-

WARE, OR ITS DOCUMENTATION. LINKSYS OFFERS NO REFUNDS FOR ITS PROD-

UCTS. Linksys makes no warranty or representation, expressed, implied, or statutory, with respect to its products or the contents or use of this documentation and all accom-

panying software, and specifically disclaims its quality, performance, merchantability, or fitness for any particular purpose. Linksys reserves the right to revise or update its prod-

ucts, software, or documentation without obligation to notify any individual or entity. Please direct all inquiries to:

Linksys P.O. Box 18558, Irvine, CA 92623. SAFETY AND REGULATORY NOTICES FCC STATEMENT The Instant Wireless Wireless-G Notebook Adapter has been tested and found to com-

ply with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment or devices

Connect the equipment to an outlet other than the receiver's

Consult a dealer or an experienced radio/TV technician for assistance Note: Combinations of power levels and antennas resulting in a radiated power level of above 100 mW equivalent isotropic radiated power (EIRP) are considered as not com-

pliant with the above mentioned directive and are not allowed for use within the European community and countries that have adopted the European R&TTE directive 1999/5/EC and/or the CEPT recommendation Rec 70.03. For more details on legal combinations of power levels and antennas, contact Linksys Corporate Compliance. Table of Contents Chapter 1: Introduction The Wireless-G Notebook Adapter Features

Linksys Group vakuuttaa tten ett Instant Wireless Wireless-G Notebook Adapter tyyppinen laite on direktiivin 1999/5/EY, direktiivin 89/336/EEC ja direktiivin 73/23/EEC oleellisten vaatimusten ja sit koskevien niden direktiivien muiden ehto-

jen mukainen. Linksys Group dclare que la Instant Wireless Wireless-G Notebook Adapter est conforme aux conditions essentielles et aux dispositions relatives la directive 1999/5/EC, la directive 89/336/EEC, et la directive 73/23/EEC.

Belgique B L'utilisation en extrieur est autoris sur le canal 11 (2462 MHz), 12 (2467 MHz), et 13 (2472 MHz). Dans le cas d'une utilisation prive, l'extrieur d'un bti-

ment, au-dessus d'un espace public, aucun enregistrement n'est ncessaire pour une distance de moins de 300m. Pour une distance suprieure 300m un enreg-

istrement auprs de l'IBPT est requise. Pour une utilisation publique l'extrieur de btiments, une licence de l'IBPT est requise. Pour les enregistrements et licences, veuillez contacter l'IBPT. France F:

2.4 GHz Bande : les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz respec-

tivement) sont compltement libres d'utilisation en France (en utilisation intrieur). Pour ce qui est des autres canaux, ils peuvent tre soumis autorisation selon le dpartment. L'utilisation en extrieur est soumis autorisation pralable et trs restreint.

2.4 GHz Band: only channels 10, 11, 12, 13 (2457, 2462, 2467, and 2472 MHz respectively) may be used freely in France for indoor use. License required for out-

door installations.

Deutschland D: Anmeldung im Outdoor-Bereich notwending, aber nicht genehmi-

gungspflichtig. Bitte mit Hndler die Vorgehensweise abstimmen.

Germany D: License required for outdoor installations. Check with reseller for proce-

dure to follow. Italia I: E' necessaria la concessione ministeriale anche per l'uso interno. Verificare con i rivenditori la procedura da seguire. L'uso per installazione in esterni non e' per-

messa. Italy I: License required for indoor use. Use with outdoor installations not allowed. The Netherlands NL License required for outdoor installations. Check with reseller for procedure to follow.

Nederlands NL Licentie verplicht voor gebruik met buitenantennes. Neem contact op

met verkoper voor juiste procedure. UG-WPC54G-112702NC BW Chapter 2: Planning Your Wireless Network Network Topology Ad-Hoc versus Infrastructure Mode Chapter 3: Getting to Know the Wireless-G Notebook Adapter The Adapters LEDs Chapter 4: Software Installation and Configuration for Windows 98SE, Me, and 2000 Overview Setup Wizard Instructions for Windows 98SE, Me, and 2000 Chapter 5: Hardware Installation Chapter 6: Driver Installation and Configuration for Windows XP Overview Driver Installation for Windows XP Windows XP Wireless Zero Configuration Chapter 7: Using the WLAN Monitor for Windows 98SE, Me, and 2000 Overview Accessing the WLAN Monitor Link Information Site Survey Profiles Creating a New Profile 1 1 1 2 2 2 4 4 5 5 6 10 11 11 11 13 15 15 15 16 18 20 22 Instant Wireless Series Wireless-G Notebook Adapter Appendix A: Troubleshooting Common Problems and Solutions Frequently Asked Questions Appendix B: Glossary Appendix C: Specifications Environmental Appendix D: Warranty Information Appendix E: Contact Information 28 28 29 33 38 39 40 41 Chapter 1: Introduction The Wireless-G Notebook Adapter Wireless-G is the upcoming 54Mbps wireless networking standard that's almost five times faster than the widely deployed Wireless-B (802.11b) prod-

ucts found in homes, businesses, and public wireless hotspots around the coun-

try but since they share the same 2.4GHz radio band, Wireless-G devices can also work with existing 11Mbps Wireless-B equipment. The new Wireless-

G Notebook Adapter from Linksys has both standards built in, so you can con-

nect your notebook to existing 802.11b infrastructure, and also the new scream-

ing fast Wireless-G networks. The included Setup Wizard will walk you through configuring the adapter to your network's settings, step by step. Then just slide it into your notebook's PC Card slot and enjoy network access with your notebook computer, while retaining true mobility. Once you're connected, you can keep in touch with your e-mail, access the Internet, and share files and other resources such as printers and network stor-

age with other computers on the network, wherever you wander. At home, you can surf the web or use instant messaging to chat with friends while sitting out on the patio.You'll also be able to connect with any of the growing number of public wireless hotspots springing up in coffee shops, airport lounges, hotels and convention centers. And as those hotspots upgrade to the new high-speed Wireless-G standard, you'll be ready to take advantage of the increased speeds.Get connected to current-standard 802.11b networks today, and be pre-

pared for the future with the Wireless-G Notebook Adapter from Linksys. Features

High-speed Wireless-G (draft 802.11g) networking for your notebook com-

puter

Data rates up to 54Mbps -- 5 times faster than Wireless-B (802.11b)

Also interoperates with Wireless-B networks (at 11Mbps)

Wireless security -- up to 128-bit WEP encryption

Free Technical Support24 Hours a Day, 7 Days a Week, Toll-Free US Calls

1-Year Limited Warranty 1 Instant Wireless Series Wireless-G Notebook Adapter If the wireless network is relatively small and needs to share resources only with the other computers on the wireless network, then the ad-hoc mode can be used. (See Figure 2-2.) Ad-hoc mode allows computers equipped with wire-

less transmitters and receivers to communicate directly with each other, elimi-

nating the need for an access point. The drawback of this mode is that, in Ad-

Hoc mode, wireless-equipped computers are not able to communicate with computers on a wired network. And, of course, communication between the wireless-equipped computers is limited by the distance and interference direct-

ly between them. Figure 2-2 Chapter 2: Planning Your Wireless Network Network Topology A wireless local area network (WLAN) is exactly like a regular local area net-

work (LAN), except that each computer in the WLAN uses a wireless device to connect to the network. Computers in a WLAN share the same frequency channel and SSID, which is an identification name for wireless devices. Ad-Hoc versus Infrastructure Mode Unlike wired networks, wireless networks have two different modes in which they may be set up: infrastructure and ad-hoc. An infrastructure configura-

tion is a WLAN and wired LAN communicating to each other through an access point. An ad-hoc configuration is wireless-equipped computers com-

municating directly with each other. Choosing between these two modes depends on whether or not the wireless network needs to share data or periph-

erals with a wired network or not. If the computers on the wireless network need to be accessed by a wired network or need to share a peripheral, such as a print-

er, with the wired network computers, the wireless network should be set up in infrastructure mode.

(See Figure 2-1.) The basis of infrastructure mode centers around an access point, which serves as the main point of communications in a wireless network. Access points transmit data to PCs equipped with wireless network cards, which can roam within a certain radial range of the access point. Multiple access points can be arranged to work in succession to extend the roaming range, and can be set up to communicate with your Ethernet (wired) hardware as well. Figure 2-1 2 3 Instant Wireless Series Wireless-G Notebook Adapter Chapter 3: Getting to Know the Wireless-G Notebook Adapter The Adapters LEDs Figure 3-1 Power Link Green. The Power LED lights up when the Adapter is pow-

ered on. Green. The Link LED lights up and stays solid when the Adapter is inserted correctly and a link is established with the Notebook. The LED flashes when there is no signal. Chapter 4: Software Installation and Configuration for Windows 98SE, Me, and 2000 Overview The Wireless-G Notebook Adapter Setup Wizard will guide you through the installation procedure for Windows 98SE, Me, and 2000. The Setup Wizard will install the WLAN Monitor and driver, as well as configure the Adapter. Important for Windows XP users: Do NOT run the Setup Wizard. Proceed directly to Chapter 5: Hardware Installation. Important for Windows 98SE, Me, and 2000 users: You must run the Setup Wizard to install the software before installing the hardware. Insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and Figure 4-1 should appear. If it does not, click the Start button and choose Run. In the field that appears, enter D:\setup.exe (if D is the letter of your CD-ROM drive). 4 Figure 4-1 5 Instant Wireless Series Wireless-G Notebook Adapter Setup Wizard Instructions for Windows 98SE, Me, and 2000 1. To install the Adapter, click the Install button on the Welcome screen, Figure 4-1. Click User Guide to view the User Guide or click Exit to exit the Setup Wizard. 2. After reading the License Agreement, click the Next button to continue the installation, or click the Cancel button to end the installation. 3. The Setup Wizard will ask you to choose a wireless mode. Click the Infrastructure Mode radio button if you want your wireless computers to network with computers on your wired network using a wireless access point. Click the Ad-Hoc Mode radio button if you want multiple wireless computers to network directly with each other. Do not use the Ad-Hoc mode if you want your wireless computers to communicate with computers on your wired network. In the SSID field, enter the SSID of your wireless network. The SSID must be identical for all devices in the network. The default setting is linksys (all lowercase). Click the Next button, or click the Back button to return to the previous page. Figure 4-2 Figure 4-3 6 7 Instant Wireless Series Wireless-G Notebook Adapter 5. The Setup Wizard will ask you to review your settings before it starts to copy files. Click the Next button to save these settings, or click the Back button to change any settings. 4. If you chose Infrastructure Mode, go to Step 5 now. If you chose Ad-Hoc Mode, select the correct operating channel for your network from the Channel drop-down menu. Then, select the Network Mode from the drop-

down menu. Click the Next button, and go to Step 4. Click the Back but-

ton to change any settings. Channel - The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which chan-

nel to use, select the default channel (Channel 6). Network Mode - Select Mixed Mode, and both Wireless-G and Wireless-

B computers will be allowed on the network, but the speed will be reduced. Select G-Only Mode for maximum speed, but no Wireless-B users will be allowed on the network. Figure 4-5 6. After the files have been successfully copied, the screen in Figure 4-6 will appear. Click the Exit button. Figure 4-4 8 9 Figure 4-6 Proceed to Chapter 5: Hardware Installation.

Instant Wireless Series Wireless-G Notebook Adapter Chapter 5: Hardware Installation Important for Windows 98SE, Me, and 2000 users: You must run the Setup Wizard to install the software before installing the hardware. Important for Windows XP users: You must install the Adapters hardware before installing the software. 1. Turn off your notebook PC. 2. Locate an available CardBus slot on your notebook PC. 3. With the Adapters label facing up, as shown in Figure 5-1, slide the Adapter completely into the CardBus slot. 4. Restart your note-

book PC. Figure 5-1 5. Windows will begin copying the driver files to your computer. If Windows asks you for the original Windows CD-ROM, insert the CD-ROM, and direct Windows to its proper location (e.g., D:\). If your PC is using Windows 98SE, Me, or 2000, proceed to the next sec-

tion, Chapter 7: Using the WLAN Monitor for Windows 98SE, Me, and 2000. If your PC is using Windows XP, proceed to Chapter 6: Driver Installation and Configuration for Windows XP. Chapter 6: Driver Installation and Configuration for Windows XP Overview After inserting the Adapter into your notebook, you will install the driver and configure the Adapter. Driver Installation for Windows XP 1. Windows XP will automatically detect the Adapter. Insert the Setup CD-

ROM into the CD-ROM drive. Click the radio button next to Install the software automatically (Recommended). Then click the Next button. Figure 6-1 10 11 2. When Windows has finished installing the driver, click the Finish button. Windows XP Wireless Zero Configuration Instant Wireless Series Wireless-G Notebook Adapter Figure 6-2 You have now completed the driver installation for the Adapter. To configure the Adapter, proceed to the next section, Windows XP Wireless Zero Configuration. For Windows XP users: Windows XP has a built-in configuration tool. Use Windows XP Wireless Zero Configuration (in the system tray at the bottom of your screen) to configure the Adapter. 1. After installing the Adapter, the Windows XP Wireless Zero Configuration icon will appear in your computers system tray (see Figure 6-3). Double-click the icon. Figure 6-3 2. The screen that appears will show any available wireless network. Select the network you want. If this network has WEP encryption enabled, go to step 3. If this network does not have WEP encryption enabled, then the screen in Figure 6-4 will appear. Check the box next to Allow me to connect to the selected wireless even though it is not secure. Then click the Connect button and go to step 4. network, Figure 6-4 Note: In Steps 2 and 3, these are the instructions and screenshots for Windows XP with Service Pack 1 installed. If you have not installed Service Pack 1, select the network you want, and click the Connect button. If the network has WEP encryption enabled, enter the WEP key in the Network key field, and then click the Connect button. 12 13 Instant Wireless Series Wireless-G Notebook Adapter Chapter 7: Using the WLA N Monitor for Windows 98SE, Me, and 2000 Overview Use the WLAN Monitor to check the link information, search for available wireless networks, or create profiles that hold different configuration settings. Accessing the WLAN Monitor After installing the Adapter, the Wireless-G Notebook Adapter WLAN Monitor icon will appear in your system tray. Double-

click the icon (see Figure 7-1). Figure 7-1 The Link Information screen will appear. From this screen, you can find out how strong the current wireless signal is and how good the connections quali-

ty is. You can also click the More Information button to view additional status information about the current wireless connection. To search for available wire-

less networks, click the Site Survey tab. To perform configuration changes, click the Profiles tab. 3. The screen in Figure 6-5 will appear. Enter the WEP key of your wireless network in the Network key field, and re-enter it in the Confirm network key field. Click the Connect button. Note: Wireless Zero Configuration does not support the use of a passphrase. Enter the exact WEP key used by your access point. Figure 6-5 4. The screen in Figure 6-6 will appear if your connection is active. Figure 6-6 For more information about WEP, refer to your access points documentation, or visit www.linksys.com. For more information about wireless networking on a Windows XP computer, enter the keyword wireless in the Windows XP search engine. Your notebook is now connected to your wireless network. Congratulations!

14 15 Figure 7-2 Instant Wireless Series Wireless-G Notebook Adapter Link Information The Link Information screen displays signal strength and link quality informa-

tion about the current connection and provides a button to click for additional status information. Figure 7-3 Ad-Hoc Mode or Infrastructure Mode - The screen indicates whether the Adapter is currently working in ad-hoc or infrastructure mode. Signal Strength - The Signal Strength bar indicates signal strength, from 0 to 100%. Link Quality - The Link Quality bar indicates the quality of the wireless net-

work connection, from 0 to 100%. Click the More Information button to view more information about the wire-

less network connection. Click the X (Close) button in the upper right corner to exit the WLAN Monitor. Figure 7-4 TCP/IP Setting IP Address - The IP Address of the Adapter. Subnet Mask - The Subnet Mask of the Adapter. Default Gateway - The Default Gateway address of the Adapter. DHCP - The status of the DHCP client. DNS - The DNS address of the Adapter. Wireless Network Status State - The status of the wireless network connection. SSID - The unique name of the wireless network. Wireless Mode - The mode of the wireless network currently in use. Transfer Rate - The data transfer rate of the current connection. Channel - The channel to which the wireless network devices are set. WEP - The status of the WEP encryption security feature. MAC - The MAC address of the wireless networks access point. Signal Strength - The Signal Strength bar indicates signal strength, from 0 to 100%. Link Quality - The Link Quality bar indicates the quality of the wireless net-

work connection, from 0 to 100%. Click the Back button to return to the initial Link Information screen. Click the X (Close) button in the upper right corner to exit the WLAN Monitor. 16 17 Instant Wireless Series Wireless-G Notebook Adapter Site Survey The Site Survey screen displays a list of infrastructure and ad-hoc networks available for connection. Figure 7-6 In the WEP drop-down box, select the type of WEP encryption used by the wireless network: 64-bit, or 128-bit WEP. If the wireless network uses a passphrase, enter the passphrase in the Passphrase field. If the wireless network uses a WEP key, enter the WEP key in the Key 1 field. Click the OK button to complete the network connection and return to the Site Survey screen, or click the Cancel button to cancel the network connection and return to the Site Survey screen. On the Site Survey screen, click the X (Close) button in the upper right corner to exit the WLAN Monitor. Figure 7-5 SSID - The SSID or unique name of the wireless network. Signal - The percentage of signal strength, from 0 to 100%. Site Information Wireless Mode - The mode of the wireless network currently in use. Channel - The channel to which the wireless network devices are set. WEP - The status of the WEP encryption security feature. MAC - The MAC address of the wireless networks access point. Surveyed at - The time at which the wireless network was scanned. Refresh - Click the Refresh button to perform a new search for wireless devices. Connect - To connect to one of the networks on the list, select the wireless net-

work, and click the Connect button. If the wireless network has WEP encryp-

tion enabled, you will see the screen shown in Figure 7-6. 18 19 Instant Wireless Series Wireless-G Notebook Adapter Profiles The Profiles screen lets you save different configuration profiles for different network setups. You can also import or export profiles. The default profile holds the initial configuration saved when you ran the Setup Wizard. Import - Click the Import button to import a profile that has been saved in another location. Select the appropriate file, and click the Open button. Figure 7-8 Export - To save the profile(s) in a different location, click the Export button. Direct Windows to the appropriate folder, and click the OK button. Figure 7-7 Profile - Name of the connection profile. SSID - The wireless networks unique name, as set in the connection profile. Profile Information Network Type - The mode of the wireless network currently in use. Transfer Rate - The data transfer rate of the current connection. (In Auto mode, the Adapter dynamically shifts to the fastest data transfer rate possible at any given time.) Channel - The channel to which the wireless network devices are set. WEP - The status of the WEP encryption security feature. Figure 7-9 Connect - To connect to a wireless network using a specific profile, select the profile, and click the Connect button. Note: If you have more than one profile, all profiles will be auto-

matically selected and exported to the same folder. Edit - Select a profile, and click the Edit button to change an existing profile. Delete - Click the Delete button to delete a profile. New - Click the New button to create a new profile. See the next section, Creating a New Profile, for detailed instructions. Click the X (Close) button in the upper right corner to exit the WLAN Monitor. 20 21 Instant Wireless Series Wireless-G Notebook Adapter Creating a New Profile 1. On the Profiles screen, click the New button to create a new profile. 2. The Choose a network type screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want your wireless computers to communicate with computers on your wired network via a wireless access point. Click the Ad-Hoc Mode radio button if you want multiple wireless computers to communicate directly with each other. Click the Next button to continue or the Back button to return to the previous screen. Infrastructure Mode - This mode allows wireless and wired networks to communicate through an access point. Ad-Hoc Mode - This mode allows wireless-equipped computers to com-

municate directly with each other. No access point is used. Figure 7-10 2. When the Create connection profile screen appears, enter a name for the new profile. Click OK to save the profile name or click Cancel to return to the previous screen. Figure 7-12 Figure 7-11 22 23 Instant Wireless Series Wireless-G Notebook Adapter 3. The Wireless Settings screen will appear. If you chose Infrastructure Mode, go to Step 4 now. If you chose Ad-Hoc Mode, select the correct operating channel for your network from the Channel drop-down menu. Then, select the Network Mode from the drop-down menu. Click the Next button, and go to Step 4. Click the Back button to change any settings. Channel - The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which chan-

nel to use, select the default channel (Channel 6). Network Mode - Select Mixed Mode, and both Wireless-G and Wireless-

B computers will be allowed on the network, but the speed will be reduced. Select G-Only Mode for maximum speed, but no Wireless-B users will be allowed on the network. 4. The Network Setting screen will appear. If your network has a DHCP server, click the radio button next to Obtain an IP address automatically (DHCP). Click the Next button to continue, or click the Back button to return to the previous screen. Then go to Step 5. If your network does not have a DHCP server, click the radio button next to Specify the IP address. Enter an IP Address, Subnet Mask, Default Gateway, and DNS appropriate for your network. Enter each address in this format: xxx.xxx.xxx.xxx (the xs represent the numbers that make up each address). You must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS addresses, then leave these fields alone. Click the Next button to continue or the Back button to return to the previ-

ous screen. Then go to Step 5. IP Address - This IP Address must be unique to your network. Subnet Mask - The Adapters Subnet Mask must be the same as your wired networks Subnet Mask. Default Gateway - Enter the IP address of your networks Gateway here. DNS - Enter the DNS addresses of your Ethernet (wired) network here. Figure 7-13 24 Figure 7-14 25 Instant Wireless Series Wireless-G Notebook Adapter 5. The Security Settings screen will appear. Enable or disable Wired Equivalent Privacy (WEP) encryption for your wireless network. If you enable WEP, enter a Passphrase or WEP key. Click the Next button to con-

tinue or the Back button to return to the previous screen. WEP (Disabled/64-bit WEP/128-bit WEP) - If you do not want to use WEP encryption, choose Disabled. To use WEP encryption (recommended to increase network security), select 64-bit or 128-bit WEP from the drop-

down menu, and enter either a Passphrase or WEP key. Passphrase - Instead of manually entering WEP keys, you can enter a Passphrase, so that a WEP key is automatically generated. It is case-sensi-

tive and should not be longer than 16 alphanumeric characters. This passphrase must match the passphrase of your wireless network and is com-

patible with other Linksys wireless products only. (If you have any non-

Linksys wireless products, enter the WEP key(s) manually on those prod-

ucts.) Key 1 - This WEP key must match the WEP key of your wireless network. If you are using 64-bit WEP encryption, then the key must consist of exact-

ly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexa-

decimal characters are 0 to 9 and A to F. 6. The Confirm New Settings screen will appear. To save the new settings, click the Yes button. To cancel the settings and return to the Profiles screen, click the No button. To edit the new settings, click the Back button. Figure 7-16 7. The Congratulations screen will appear next. Click Activate new settings now to implement the new settings immediately and return to the Link Information screen. Click Activate new settings later to keep the current settings active, and return to the Profiles screen so that you can edit your profile or create another profile. Figure 7-15 Figure 7-17 You have successfully created a connection profile. Click the X (Close) but-

ton in the upper right corner to exit the WLAN Monitor. 26 27 Instant Wireless Series Wireless-G Notebook Adapter 3. I cannot communicate with a wired computer linked via an access point in the infrastructure configuration.

Make sure that the notebook PC is powered on.

Make sure that the Adapter is configured with the same SSID and security options as the other computers in the infrastructure configuration. Frequently Asked Questions Can I run an application from a remote computer over the wireless network?

This will depend on whether or not the application is designed to be used over a network. Consult the applications user guide to determine if it supports oper-

ation over a network. Can I play computer games with other members of the wireless network?

Yes, as long as the game supports multiple players over a LAN (local area net-

work). Refer to the games user guide for more information. What is the IEEE 802.11b standard?

It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware from different manufacturers to commu-

nicate, provided that the hardware complies with the 802.11b standard. The 802.11b standard states a maximum data transfer rate of 11Mbps and an oper-

ating frequency of 2.4GHz. Appendix A: Troubleshooting Common Problems and Solutions This chapter provides solutions to problems that may occur during the installa-

tion and operation of the Wireless-G Notebook Adapter. Read the descriptions below to solve your problems. If you cant find an answer here, check the Linksys website at www.linksys.com. 1. My computer does not recognize the Adapter.

Make sure the Adapter is properly inserted into the CardBus slot. Note that the Adapter can be inserted either way, but is correctly only when it is insert-

ed so that the Instant Wireless logo on the front of the Adapter cannot be seen. If in doubt, try inserting the Adapter both ways. The Adapter will slide in further when it is correct. 2. The Adapter does not work properly.

Reinsert the Adapter into your notebooks CardBus slot. A beep should be heard if the Adapter is properly inserted.

For non-Windows environments, make sure that a PCMCIA card service driver is installed on your PC.

Open the Control Panel and click the PC Card. Check whether it has a PCMCIA card in one of the sockets or not. If you find the Adapter in one of the sockets, it means that the Adapter has been detected properly. If you see a yellow question mark, the resources are in conflict.

Right-click My Computer and select Properties. Select Device Manager and click the Network Adapter. You will find the Wireless-G Notebook Adapter if it is installed successfully. If you see the yellow exclamation mark, the resources are in conflict. Click PCMCIA card and then click PCMCIA card service. You will see the status of the Adapter. If there is a yellow ques-

tion mark please check the following:

Make sure that your notebook has a free IRQ.

Make sure that you have inserted the right Adapter and installed the prop-

er driver. If the Adapter does not function after attempting the above steps, remove the Adapter and do the following:

Uninstall the driver software from your PC.

Restart your PC and repeat the hardware and software installation as spec-

ified in this User Guide. 28 29 Instant Wireless Series Wireless-G Notebook Adapter What IEEE 802.11b features are supported?

The product supports the following IEEE 802.11b functions:

CSMA/CA plus Acknowledge protocol

Multi-Channel Roaming

Automatic Rate Selection

RTS/CTS feature

Fragmentation

Power Management What is ad-hoc mode?

When a wireless network is set to ad-hoc mode, the wireless-equipped com-

puters are configured to communicate directly with each other. The ad-hoc wireless network will not communicate with any wired network. What is infrastructure mode?

When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a wired network through a wireless access point. What is roaming?

Roaming is the ability of a portable computer user to communicate continu-

ously while moving freely throughout an area greater than that covered by a sin-

gle access point. Before using the roaming function, the workstation must make sure that it is the same channel number with the access point of dedicated cov-

erage area. To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each node and access point, for example, must always acknowledge receipt of each message. Each node must maintain contact with the wireless network even when not actually transmitting data. Achieving these functions simultaneously requires a dynamic RF networking technology that links access points and nodes. In such a system, the users end node under-

takes a search for the best possible access to the system. First, it evaluates such factors as signal strength and quality, as well as the message load currently being carried by each access point and the distance of each access point to the wired backbone. Based on that information, the node next selects the right access point and registers its address. Communications between end node and host computer can then be transmitted up and down the backbone. As the user moves on, the end nodes RF transmitter regularly checks the sys-

tem to determine whether it is in touch with the original access point or whether it should seek a new one. When a node no longer receives acknowledgment from its original access point, it undertakes a new search. Upon finding a new access point, it then re-registers, and the communication process continues. What is ISM band?

The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe. What is Spread Spectrum?

Spread Spectrum technology is a wideband radio frequency technique devel-

oped by the military for use in reliable, secure, mission-critical communica-

tions systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum

(DSSS) and Frequency Hopping Spread Spectrum (FHSS). What is DSSS? What is FHSS? And what are their differences?

Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-Sequence Spread-Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during trans-

mission, statistical techniques embedded in the radio can recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most nar-

rowband receivers. 30 31 Instant Wireless Series Wireless-G Notebook Adapter Would the information be intercepted while transmitting on air?

WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security fea-

ture of scrambling. On the software side, WLAN offers the encryption function

(WEP) to enhance security and access control. What is WEP?

WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 64-bit or 128-bit shared key algorithm, as described in the IEEE 802.11 standard. Appendix B: Glossary 802.11b - One of the IEEE standards for wireless networking hardware. Products that adhere to a specific IEEE standard will work with each other, even if they are manufactured by different companies. The 802.11b standard specifies a maximum data transfer rate of 11Mbps, an operating frequency of 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.11g - Refers to the proposed extension of the IEEE 802.11 standard for wireless networking, which has not been ratified by IEEE. The draft 802.11g specifications used by Linksys specifies a maximum data transfer rate of 54Mbps using OFDM modulation, an operating frequency of 2.4GHz, back-

ward compatibility with IEEE 802.11b devices and WEP encryption for secu-

rity. Ad-hoc Network - An ad-hoc network is a group of computers, each with a wireless adapter, connected as an independent 802.11 wireless LAN. Ad-hoc wireless computers operate on a peer-to-peer basis, communicating directly with each other without the use of an access point. Ad-hoc mode is also referred to as an Independent Basic Service Set (IBSS) or as peer-to-peer mode, and is useful at a departmental scale or SOHO operation. CTS (Clear To Send) - An RS-232 signal sent from the receiving station to the transmitting station that indicates it is ready to accept data. Default Gateway - The router used to forward all traffic that is not addressed to a station within the local subnet. DHCP (Dynamic Host Configuration Protocol) - A protocol that lets network administrators manage centrally and automate the assignment of Internet Protocol (IP) addresses in an organizations network. Using the Internets set of protocol (TCP/IP), each machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users with a con-

nection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered manually at each computer and, if computers move to another location in another part of the network, a new IP address must be entered. DHCP lets a network administrator supervise and dis-

tribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network. 32 33 Instant Wireless Series Wireless-G Notebook Adapter DHCP uses the concept of a lease or amount of time that a given IP address will be valid for a computer. The lease time can vary depending on how long a user is likely to require the Internet connection at a particular location. Its espe-

cially useful in education and other environments where users change fre-

quently. Using very short leases, DHCP can dynamically reconfigure networks in which there are more computers than there are available IP addresses. DHCP supports static addresses for computers containing Web servers that need a permanent IP address. DNS - The domain name system (DNS) is the way that Internet domain name are located and translated into Internet Protocol (IP) addresses. A domain name is a meaningful and easy-to-remember handle for an Internet address. DSSS (Direct-Sequence Spread Spectrum) - DSSS generates a redundant bit pattern for all transmitted data. This bit pattern is called a chip (or chipping code). Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the receiver can recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. However, to an intended receiver (i.e. another wireless LAN end-

point), the DSSS signal is recognized as the only valid signal, and interference is inherently rejected (ignored). Dynamic IP Address - An IP address that is automatically assigned to a client station in a TCP/IP network, typically by a DHCP server. Network devices that serve multiple users, such as servers and printers, are usually assigned static IP addresses. ESS (Extended Service Set) - A set of more than two or more BSSs (multiple access points) forming a single network. Firmware - Code that is written onto read-only memory (ROM) or program-

mable read-only memory (PROM). Once firmware has been written onto the ROM or PROM, it is retained even when the device is turned off. IEEE - The Institute of Electrical and Electronics Engineers. The IEEE describes itself as the worlds largest technical professional societypromot-

ing the development and application of electrotechnology and allied sciences for the benefit of humanity, the advancement of the profession, and the well-

being of our members. The IEEE fosters the development of standards that often become national and international standards. The organization publishes a number of journals, has many local chapters, and several large societies in special areas, such as the IEEE Computer Society. Infrastructure Network - An infrastructure network is a group of computers or other devices, each with a wireless adapter, connected as an 802.11 wireless LAN. In infrastructure mode, the wireless devices communicate with each other and to a wired network by first going through an access point. An infra-

structure wireless network connected to a wired network is referred to as a Basic Service Set (BSS). A set of two or more BSS in a single network is referred to as an Extended Service Set (ESS). Infrastructure mode is useful at a corporation scale, or when it is necessary to connect the wired and wireless networks. IP Address - In the most widely installed level of the Internet Protocol (IP) today, an IP address is a 32-binary digit number that identifies each sender or receiver of information that is sent in packet across the Internet. When you request an HTML page or send e-mail, the Internet Protocol part of TCP/IP includes your IP address in the message (actually, in each of the packets if more than one is required) and sends it to the IP address that is obtained by looking up the domain name in the Uniform Resource Locator you requested or in the e-mail address you're sending a note to. At the other end, the recipient can see the IP address of the Web page requester or the e-mail sender and can respond by sending another message using the IP address it received. IPCONFIG - A utility that provides for querying, defining and managing IP addresses within a network. A commonly used utility, under Windows NT and 2000, for configuring networks with static IP addresses. ISP - An ISP (Internet service provider) is a company that provides individuals and companies access to the Internet and other related services such as Web site building and virtual hosting. LAN - A local area network (LAN) is a group of computers and associated devices that share a common communications line and typically share the resources of a single processor or server within a small geographic area (for example, within an office building). MAC Address - The MAC (Media Access Control) address is your computers unique hardware number. 34 35 Instant Wireless Series Wireless-G Notebook Adapter mIRC - mIRC runs under Windows and provides a graphical interface for log-

ging onto IRC servers and listing, joining and leaving channels. Network Mask - also known as the Subnet Mask. OFDM - Developed for wireless applications, Orthogonal Frequency Division Multiplexing (OFDM) technology offers superior performance-increased data rates and more reliable transmissions-than previous technologies, such as DSSS. OFDM is a scheme in which numerous signals of different frequencies are combined to form a single signal for transmission on the medium. OFDM works by breaking one high-speed data stream into a number of lower-

speed data streams, which are then transmitted in parallel. Each lower speed stream is used to modulate a subcarrier. Essentially, this creates a multi-carrier transmission by dividing a wide frequency band or channel into a number of narrower frequency bands or sub-channels. OFDM is also used for other appli-

cations, including powerline networking. Plug-and-Play - The ability of a computer system to configure expansion boards and other devices automatically without requiring the user to turn off the system during installation. Roaming - In an infrastructure mode wireless network, this refers to the abili-

ty to move out of one access point's range and into another and transparently reassociate and reauthenticate to the new access point. This reassociation and reauthentication should occur without user intervention and ideally without interruption to network connectivity. A typical scenario would be a location with multiple access points, where users can physically relocate from one area to another and easily maintain connectivity. SSID (Service Set Identifier) - An identification name that wireless devices use to make connections. In order for wireless devices to communicate, they must all be set to the same channel and they all must use the same SSID. For instance, if you are using an access point to connect two computers using wire-

less devices, the access point and each of the wireless devices must use the same SSID. Even if they are set to the same channel, they cannot communicate unless the SSID is the same. Static IP Address - A permanent IP address that is assigned to a node in a TCP/IP network. Subnet Mask - The method used for splitting IP networks into a series of sub-

groups, or subnets. The mask is a binary pattern that is matched up with the IP address to turn part of the host ID address field into a field for subnets. TCP (Transmission Control Protocol) - A method (protocol) used along with the IP (Internet Protocol) to send data in the form of message units (datagram) between network devices over a LAN or WAN. While IP takes care of handling the actual delivery of the data (routing), TCP takes care of keeping track of the individual units of data (called packets) that a message is divided into for effi-

cient delivery over the network. TCP is known as a "connection oriented" pro-

tocol due to requiring the receiver of a packet to return an acknowledgment of receipt to the sender of the packet resulting in transmission control. TCP/IP (Transmission Control Protocol/Internet Protocol) - The basic com-

munication language or set of protocols for communications over a network

(developed specifically for the Internet). TCP/IP defines a suite or group of protocols and not only TCP and IP. UDP (User Datagram Protocol) - A method (protocol) used along with the IP

(Internet Protocol) to send data in the form of message units (datagram) between network devices over a LAN or WAN. While IP takes care of handling the actual delivery of the data (routing), UDP takes care of keeping track of the individual units of data (called packets) that a message is divided into for effi-

cient delivery over the network. UDP is known as a connection-less protocol due to NOT requiring the receiver of a packet to return an acknowledgment of receipt to the sender of the packet (as opposed to TCP). WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-

bit shared key algorithm, as described in the IEEE 802.11b standard. WINIPCFG - Configuration utility based on the Win32 API for querying, defining and managing IP addresses within a network. A commonly used util-

ity under Windows 95, 98SE, and Me. WLAN (Wireless Local Area Network) - A group of computers and associat-

ed devices that communicate with each other wirelessly. 36 37 Appendix C: Specifications Environmental Instant Wireless Series Wireless-G Notebook Adapter Standards:

IEEE 802.11b, IEEE draft 802.11g Dimensions:

Modulations:

Channels:

802.11b, draft 802.11g 802.11b: CCK (11 Mbps), DQPSK (2 Mbps), DBPSK (1 Mbps); 802.11g: OFDM 11 Channels (USA) 13 Channels (Europe) 14 Channels (Japan) PCMCIA:

CardBus RF Outpur power 20dBm LEDs:

Power, Link WEP Key Bits:

64-Bit and 128-Bit 4.53" x 2.13" x 0.30"

(115 mm x 54 mm x 7.5 mm) Unit Weight:

1.66 oz. (0.047 kg) Power:

3.3V Bus powered Certifications:

FCC, CE Operating Temp.:

32F to 185F (0C to 85C) Storage Temp.:

40F to 194F (-40C to 90C) Operating Humidity:

5% to 95%, Non-Condensing Storage Humidity:

5% to 95%, Non-Condensing 38 39 Instant Wireless Series Wireless-G Notebook Adapter Appendix D: Warranty Information BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE FROM THE PRODUCTS PACKAGING ON HAND WHEN CALLING. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. IN NO EVENT SHALL LINKSYS LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDEN-

TAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS DOCU-

MENTATION. LINKSYS DOES NOT OFFER REFUNDS FOR ANY PROD-

UCT. LINKSYS OFFERS CROSS SHIPMENTS, A FASTER PROCESS FOR PRO-

CESSING AND RECEIVING YOUR REPLACEMENT. LINKSYS PAYS FOR UPS GROUND ONLY. ALL CUSTOMERS LOCATED OUTSIDE OF THE UNITED STATES OF AMERICA AND CANADA SHALL BE HELD RESPONSIBLE FOR SHIPPING AND HANDLING CHARGES. PLEASE CALL LINKSYS FOR MORE DETAILS. Appendix E: Contact Information For help with the installation or operation of the Wireless-G Notebook Adapter, contact Linksys Technical Support at one of the phone numbers or Internet addresses below. Sales Information Technical Support RMA (Return Merchandise Authorization) Issues Fax E-mail Web FTP Site 800-546-5797 (LINKSYS) 800-326-7114 www.linksys.com (or call 949-271-5461) 949-265-6655 support@linksys.com http://www.linksys.com ftp.linksys.com 40 41 http://www.linksys.com Copyright 2003 Linksys, All Rights Reserved.