Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router Last Modified: 2018-06-24 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 20172018 Cisco Systems, Inc. All rights reserved. C O N T E N T S C H A P T E R 1 Overview of Cisco 1100 Series Integrated Services Routers 1 About Cisco 1100 Series Integrated Service Routers 1 5 2 Chassis Views LED Indicators Reset Button 11 Power Supply 11 Slots and Interfaces 11 About Slots, Subslots, and Port Numbering 11 Specifications of Cisco 1100 Series Integrated Services Routers 12 Periodic Inspection and Cleaning 12 C H A P T E R 2 Prepare for Router Installation 13 Safety Recommendations 13 Safety With Electricity 13 Prevent Electrostatic Discharge Damage 14 General Site Requirements Site Selection Guidelines 15 16 16 Rack Requirements Router Environmental Requirements Power Guidelines and Requirements Network Cabling Specifications 18 Console Port Connections 18 EIA/TIA-232 18 USB Serial Console 18 Console Port Considerations Preparing for Network Connections 19 17 17 19 Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router iii Contents Ethernet Connections 19 Required Tools and Equipment for Installation and Maintenance 20 C H A P T E R 3 Install and Connect the Router 21 Unpack the Router Set up Router on Desktop, Rack, or Wall 21 21 Rack Mount 22 Attach the Brackets Mount the Router 22 23 Wall Mount 23 Wall Mount Using Key-hole Slots 24 Wall Mount Using DIN Rail Brackets 29 Chassis Grounding 30 Connect Power Cable Connect the Router to a Console 31 32 Connect to the Serial Port with Microsoft Windows Connect to the Console Port with Mac OS X 33 Connect to the Console Port with Linux 34 33 Connect WAN and LAN Interfaces 34 Ports and Cabling 35 Connection Procedures and Precautions 36 Configure the Router at Startup 36 C H A P T E R 4 Install and Upgrade Internal Modules and FRUs 37 Access Internal Modules 37 Replace the Chassis Cover 37 Remove the Cover Replace the Cover 37 38 Locate Internal and External Slots for Modules 39 Install the Universal POE Splitter LTE Pluggable Module 40 39 Insert a Micro-SIM Card 42 Remove and Replace the 1GB Flash Token Memory Stick 43 Remove and Replace the Cisco 1100 Series ISRs Power Supplies 43 Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router iv Contents Install and Remove SFP Modules 44 Remove the SFP Modules 44 C H A P T E R 5 ROM Monitor Overview and Basic Procedures 45 ROM Monitor Overview 45 C H A P T E R 6 FCC Supplier Declaration of Conformity 47 Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router v Contents Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router vi C H A P T E R 1 Overview of Cisco 1100 Series Integrated Services Routers Cisco 1100 Series Integrated Services Routers (ISRs) with Cisco IOS XE Software are high-performance devices that are easy to deploy and manage. The routers combine Internet access, comprehensive security, and wireless services (LTE Advanced 3.0, Wireless WAN and Wireless LAN). About Cisco 1100 Series Integrated Service Routers, on page 1 Periodic Inspection and Cleaning, on page 12 About Cisco 1100 Series Integrated Service Routers The Cisco 1100 series Integrated Services Routers are the next generation, IOS XE based, multi core, branch routers. They are available in both fixed and modular form factors. The Cisco 1100 series is best suited for small and midsize businesses, enterprise branches and as customer premises equipment in managed services environments. Table1:BasemodelsoftheCisco1100seriesISR Feature C111x-8P C111x-4P C1101-4PLTEPWx C1101-4P Front panel switch ports 8 4 4 4 WAN ports 2 (1 Combo RJ-45/SFP + 1 RJ-45) 2 (1 Combo RJ-45/SFP + 1 RJ-45) 1 RJ-45 1 RJ-45 Console port Serial RJ-45, Micro USB Serial RJ-45, Micro USB Micro USB Micro USB
(Optional) POE 4PoE/2PoE+
2 POE/1 POE+
None
(Optional)WLAN 802.11ac WAVE 2 802.11ac WAVE 2 802.11ac WAVE 2
(C1101-4PLTEPWx) None None Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 1 Chassis Views Overview of Cisco 1100 Series Integrated Services Routers Feature C111x-8P C111x-4P C1101-4PLTEPWx C1101-4P LTE (optional) 4G LTE-Advanced
(CAT6) with carrier aggregation 4G LTE-Advanced
(CAT6) with carrier aggregation DSL (optional) G.FAST, VDSL2 and ADSL2/2+
VDSL2 and ADSL2/2+
None 4G pluggable LTE
(CAT 4) and pluggable LTE Advanced (CAT 6) with carrier aggregation None None Note Multiple variations of the models are available based on LTE/WLAN/DSL/Ethernet options on the routers. For more information on the features and specifications of Cisco 1100 Series Integrated Services Routers
(ISRs), refer to the Cisco 1000 Series Integrated Services Routers Solution Overview document and Cisco 1000 Series Integrated Services Routers datasheet. Chassis Views This section contains front and back panel views of the Cisco 1100 Series ISR-showing locations of the power and signal interfaces, interface slots, status indicators, and chassis identification labels. Figure1:Cisco111xSeries-BezelView 1 3 5 7 Status WiFi LTE Signal Intensity Illuminated Cisco Logo 2 4 6 VPN GPS LTE Data/SIM Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 2 Overview of Cisco 1100 Series Integrated Services Routers Chassis Views Figure2:Cisco111x-8P-I/OView 1 3 5 7 9 11 13 15 17 19 LTE Antennas Main and Diversity GPS Connection Serial Number Reset Button 4-pin Power Connector GE 0/0/0 - RJ45 USB3.0 LTE Provisioning Port DSL Product Identification Number (PID) 2 4 6 8 10 12 14 16 18 Ethernet Switch CLEI Label Grounding Power Switch GE 0/0/1 GE 0/0/0 - SFP Lower slot0 Upper slot1 RJ45 / Micro USB Console Kensington Lock Slot Note For more information on the Reset Button, refer to the Reset Overview section in the ISR 1000 Series Integrated Services Routers. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 3 Chassis Views Overview of Cisco 1100 Series Integrated Services Routers Figure3:Cisco1101-4PISR-FrontView 1 Non-illuminated Cisco Logo Figure4:Cisco1101-4PISR-I/OView 1 3 5 7 9 Kensington Lock Slot Power Switch Reset Button GE WAN USB3.0 2 4 6 8 Figure5:Cisco1101-4PLTEP-BezelView Grounding 4-pin Power Connector LAN: 0-4 Micro USB Console 1 Non-illuminated Cisco logo Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 4 Overview of Cisco 1100 Series Integrated Services Routers LED Indicators Figure6:Cisco1101-4PLTEP-I/OView 1 3 5 7 9 Power Switch Reset Button GE WAN USB 3.0 Grounding 2 4 6 8 10 4-pin Power Connector LAN:0-4 Micro-USB console Port Pluggable Kensington Lock Slot LED Indicators The following figures and table summarizes the LED indicators that are located in the bezel or chassis of the C111x series. Figure7:LEDIndicators-BezelSide 1 3 Status WLAN 2 4 VPN GPS Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 5 LED Indicators Overview of Cisco 1100 Series Integrated Services Routers 5 7 Figure8:LEDIndicators-I/OSide LTE RSSI/Mode 6 LTE DATA/SIM Cisco Logo 1 3 5 7 9 11 GE WAN Ports: 0-7
(0,2,4,6 at the top and 1,3,5,7 at the bottom) GE1 LED USB LED USB Console CD LED DATA LED 2 4 6 8 10 PoE LED GE0 LED RJ-45 Console LED Micro USB Console LED DSL The following table summarizes the LED indicators that are located in the bezel or chassis of the C111x series. Table2:LEDIndicatorsforC111x Port Cisco Logo LED Color Blue Description Illuminated Cisco logo. Indicates router power is good. Control Source Bezel side Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 6 Overview of Cisco 1100 Series Integrated Services Routers LED Indicators Port STATUS
(System Status) LED Color Description Control Source Green and Amber Bezel side. All models. Steady Green - System operates normally. OffSystem is not out of reset or BIOS image is not loadable. Blinking Amber BIOS/Rommon is booting. Steady Amber BIOS/Rommon has completed booting, and the system is at the Rommon prompt or booting the platform software. VPN OK Green OffNo tunnel. Bezel side LTE RSSI/Mode Green and Amber Bezel Side Steady On At least one tunnel is up. No LEDs OnNo Service 1 LED On RSSI is under -100dBm. 2 LEDs On Low RSSI,
-99dbm <> -90dBm. 3 LEDs On Medium RSSI -89dBm <>
-70dBm. 4 LEDs On High RSSI,
> -69dBm. Green LTE Amber 3G Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 7 LED Indicators Overview of Cisco 1100 Series Integrated Services Routers Port GPS LED Color Green WLAN Green, Red, and Amber Ethernet Switch GE LAN Ports, Non-PoE Green Ethernet Switch GE LAN Ports, with PoE Green and Amber Control Source Bezel Side Bezel side Description On - GPS coordinates are acquired. Off - GPS is disabled, GPS is enabled without GPS mode and NMEA configuration, or GPS is acquiring. Green Standalone GPS Off GPS not configured On GPS configured Green Normal operating condition with at least one wireless client association. RedEthernet link is not operational or Ethernet failure. AmberSoftware upgrade is in progress. Off No link I/O side I/O side Steady On link Blink TXD/RXD data Off No link, no device powered, PD denied power, power delivery fault PoE administratively disabled. Green Steady On link;
if PoE device, power is enabled. Green Blink TXD/RXD data Amber - PoE Fault GE WAN Ports Green Off No link I/O side Steady On link Blink TXD/RXD data Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 8 Overview of Cisco 1100 Series Integrated Services Routers LED Indicators Port DSL CD LED Color Green Description Off Shut Control Source I/O Side PoE OK Green Green Blink Training, or no shut and cable disconnected. Green Steady On Trained Green Steady On
-53.5V PoE power supply connected and all powered port operating normally. Off No -53.5V PoE power supply connected to router. I/O Side DSL Data Green Off No Data Activity I/O Side Console/AUX Green and Amber Green Blink TX/RX Data Green On Console enabled. Amber On AUX enabled. I/O side USB Console Green Off No USB device discovered. I/O side USB Green On USB device discovered. Off: No USB device discovered. On: USB device discovered. I/O Side Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 9 LED Indicators Overview of Cisco 1100 Series Integrated Services Routers Table3:LEDIndicatorsforC1101-X LED Power Color Green+Amber VPN OK Green Ethernet Switch GE LAN Ports Green GE WAN Ports Green LTE DATA/SIM
(C1101-4PLTEPWz C1101-4PLTEP/C1101-4PLTEPWx) Green and Amber Description Control Source I/O I/O I/O I/O Bezel Side System Power Status Off: No Power Green Steady On: Normal operation Green Blink: Boot up phase or in ROMMON mode Amber Steady on Or Blink: Some issues with the system. VPN Status Off: No tunnel Steady on:At least one tunnel is up Link Activity Off: No link Steady on: Link Blink: TXD/RXD Data Link Activity Off: No link Steady on: Link Blink: TXD/RXD Data Single LTE Modem (one modem with SIM switch-over capability). Off: Modem not up or modem up and no SIM. Amber Steady On:
Modem up, SIM installed but not active. Green Blink: LTE data activity. WLAN
(C1101-4PLTEPWx) 3-color LED: Green, Red and Amber WLAN Functions I/O Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 10 Overview of Cisco 1100 Series Integrated Services Routers Reset Button LED USB Console Color Green USB 3.0 Green Description Control Source I/O I/O USB Console Status OFF: USB console is not active. ON: USB console is active. USB 3.0 Status OFF: No USB device is connected. ON: USB device is commected. Reset Button The actuation of the Reset button is only recognized during ROMMON boot, that is, as the router comes to the ROMMON prompt. The Reset button does not require much force to be actuated. The Reset button should be actuated only with a small implement such as the tip of a pen or a paper clip. When the Reset button is pressed at startup, the system LED turns green. For more information, see the "Reset Overview" section of the Cisco 1100 Software Configuration Guide. Power Supply Cisco 111x Series ISRs support PoE and PoE+ power to endpoints. The product power specifications are as follows:
AC input voltage: Universal 100 to 240 VAC Frequency: 50 to 60 Hz Maximum output power: Up to 66W for non-PoE supply and up to 125W for PoE supply Optional PoE and PoE+
Output voltage: +12VDC for system power and -53.5VDC for PoE power Slots and Interfaces About Slots, Subslots, and Port Numbering The Cisco 1100 series designates its interfaces using a 3-tuple notation that lists the slot, sub slot and port in the format slot/sub-slot/port. The slot number is reserved for the mother board, which is "0". Each interface type is allocated a sub slot and the port number is a unique port on the interface. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 11 Specifications of Cisco 1100 Series Integrated Services Routers Overview of Cisco 1100 Series Integrated Services Routers Table4:Slot,Bay,andPortNumbering Subslot 0 1 2 3 4 Interface Type Ethernet LAN Ethernet WAN LTE DSL WIFI Specifications of Cisco 1100 Series Integrated Services Routers For specifications on the Cisco 1100 Series ISRs, refer to the Cisco 1100 Series ISR Specifications document. Periodic Inspection and Cleaning We recommend that you periodically inspect and clean the external surface of the router is recommended to minimize the negative impact of environmental dust or debris. The frequency of inspection and cleaning is dependent upon the severity of the environmental conditions, but we recommend a minimum once every six months. Cleaning involves vacuuming router air intake and exhaust vents. Note Sites with ambient temperatures consistently above 25C or 77F and with potentially high levels of dust or debris might require periodic preventative maintenance cleaning. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 12 C H A P T E R 2 Prepare for Router Installation Before you install the Cisco 1100 Series Integrated Services Routers, you must prepare your site for the installation. This chapter provides pre-installation information, such as recommendations and requirements that should be considered before installing your router. See the following sections to prepare for installation:
Safety Recommendations, on page 13 General Site Requirements, on page 15 Rack Requirements, on page 16 Router Environmental Requirements, on page 17 Power Guidelines and Requirements, on page 17 Network Cabling Specifications, on page 18 Required Tools and Equipment for Installation and Maintenance, on page 20 Safety Recommendations Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040. Safety With Electricity Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001 Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 13 Prevent Electrostatic Discharge Damage Prepare for Router Installation Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions. Statement 1015 Warning Only trained and qualified personnel should be allowed to install or replace this equipment Statement 1030 Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada:Canadian Electrical Code, Section 54). Statement 1052 Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035 Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Prevent Electrostatic Discharge Damage Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It can occur if electronic printed circuit cards are improperly handled and can cause complete or intermittent failures. Always follow ESD prevention procedures when removing and replacing modules:
Ensure that the router chassis is electrically connected to ground. Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to an unpainted surface of the chassis frame to channel unwanted ESD voltages safely to ground. To guard against ESD damage and shocks, the wrist strap and cord must operate effectively. If no wrist strap is available, ground yourself by touching a metal part of the chassis. Caution For the safety of your equipment, periodically check the resistance value of the anti-static strap. It should be between 1 and 10 megohms (Mohm). Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 14 Prepare for Router Installation General Site Requirements General Site Requirements Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning Connect the Chassis to Earth GroundTo reduce the risk of electric shock, the chassis of this equipment needs to be connected to permanent earth ground during normal use. Statement CS-0445 Warning This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. Statement 1005 Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052 Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:
This unit should be mounted at the bottom of the rack if it is the only unit in the rack. When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006. Warning To prevent the system from overheating, do not operate the devices in an area that exceeds the maximum recommended ambient temperature:
C111x 40 C C1101 45 C Statement 1047 Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 15 Site Selection Guidelines Prepare for Router Installation Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection, LAN, PoE. Statement 1044. Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 1.75 in. (4.4 cm). Statement 1076. Site Selection Guidelines The Cisco 1100 Series ISRs require specific environmental operating conditions. Temperature, humidity, altitude, and vibration can affect the performance and reliability of the router. The following sections provide specific information to help you plan for the proper operating environment. The Cisco 1100 Series ISRs are designed to meet the industry EMC, safety, and environmental standards described in the Regulatory Compliance and Safety Information for the Cisco 1100 Series ISR document. Rack Requirements For the Cisco 111x Series ISRs, use brackets with a 19-inch rack. Note Rack requirements is applicable only for C111x Routers The following information can help you plan your equipment rack configuration:
Allow clearance around the rack for maintenance. Allow at least one rack unit of vertical space between routers; more clearance is required when stacking multiple Cisco 1100 Series ISRs. Provide adequate heat removal mechanism to keep the surrounding air temperature well within the specified operating temperature condition. Note More spacing may be required depending on the installation environment. Enclosed racks must have adequate ventilation. Ensure that the rack is not congested, because each router generates heat. An enclosed rack should have louvered sides and a fan to provide cooling air. Heat generated by equipment near the bottom of the rack can be drawn upward into the intake ports of the equipment above it. When mounting a chassis in an open rack, ensure that the rack frame does not block the intake or exhaust ports. If the chassis is installed on slides, check the position of the chassis when it is seated in the rack. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 16 Prepare for Router Installation Router Environmental Requirements Router Environmental Requirements Cisco 1100 Series ISRs can be placed on a desktop, installed in a rack, or mounted on a wall. The location of your router and the layout of your equipment rack or wiring room are extremely important considerations for proper operation. Equipment placed too close together, inadequate ventilation, and inaccessible panels can cause malfunctions and shutdowns, and can make maintenance difficult. Plan for access to both front and rear panels of the router. Note Only C111x Series support rack installation and DIN Rail mounting. When planning your site layout and equipment locations, refer to the General Site Requirements , section. If you are currently experiencing shutdowns or an unusually high number of errors with your existing equipment, these precautions and recommendations may help you isolate the cause of failure and prevent future problems. Ensure that the room where your router operates has adequate air circulation. Electrical equipment generates heat. Without adequate air circulation, ambient air temperature may not cool equipment to acceptable operating temperatures. Always follow ESD-prevention procedures described in the Preventing Electrostatic Discharge Damage to avoid damage to equipment. Damage from static discharge can cause immediate or intermittent equipment failure. Baffles can help to isolate exhaust air from intake air, which also helps to draw cooling air through the chassis. The best placement of the baffles depends on the airflow patterns in the rack, which can be found by experimenting with different configurations. When equipment installed in a rack (particularly in an enclosed rack) fails, try operating the equipment by itself, if possible. Power off other equipment in the rack (and in adjacent racks) to allow the router under test a maximum of cooling air and clean power. Power Guidelines and Requirements Check the power at your site to ensure that you are receiving power that is free of spikes and noise. Install a power conditioner if necessary. Power Guidelines and Requirements lists power requirements for the Cisco 1100 Series ISRs. Table5:PowerRequirementsforCisco1100SeriesISRs Power Source 66W AC Power Adapter
(PWR-66W-AC-V2) 125W AC Power Adapter
(PWR-125W-AC) Input Rated 100-240V, 2A Output Rated 12 VDC, 5.5A 100-240 VAC, 2A, 50-60 Hz 12VDC, 3.5A; -53.5Vdc, 1.55A Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 17 Network Cabling Specifications Prepare for Router Installation Power Source Input Rated Output Rated 115W AC Power Adapter
(PWR-115W-AC) 100-240VAC, 2A, 50-60 Hz 12V, 4.6A, -53.5V 1.12A 30W AC Power Adapter
-
-
Network Cabling Specifications The following sections describe the cables and thee specifications required to install Cisco 1100 Series ISRs:
Console Port Connections The C111x has both EIA/TIA-232 asynchronous (RJ-45) and USB 5-pin micro Type B, 2.0 compliant serial console ports. The console ports do not have any hardware flow control. Shielded USB cables with properly terminated shields are recommended. EIA/TIA-232 Depending on the cable and the adapter used, this port appears as a DTE or DCE device at the end of the cable. Only one port can be used at the same time. The default parameters for the console port are 9600 baud, 8 data bits, 1 stop bit, and no parity. The console port does not support hardware flow control. For detailed information about installing a console terminal, see the Connecting to a Console Terminal or Modem section. For cable and port pinouts, see the Cisco Modular Access Router Cable Specifications document located on Cisco.com. USB Serial Console The USB serial console port connects directly to the USB connector of a PC using a USB Type A to 5-pin micro USB Type-B cable. The USB Console supports full speed (12Mb/s) operation. The console port does not support hardware flow control. Note Always use shielded USB cables with a properly terminated shield. The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 1 stop bit. For detailed information about installing a console terminal, see the Connecting to a Console Terminal or Modem section on page 3-19. For operation with a Microsoft Windows OS version older than Windows 7, the Cisco Windows USB Console Driver must be installed on any PC connected to the console port. If the driver is not installed, prompts guide you through a simple installation process. The Cisco Windows USB Console Driver allows plugging and unplugging the USB cable from the console port without affecting Windows HyperTerminal operations. No special drivers are needed for Mac OS X or Linux. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 18 Prepare for Router Installation Console Port Considerations Only one console port can be active at a time. When a cable is plugged into the USB console port, the RJ-45 port becomes inactive. Conversely, when the USB cable is removed from the USB port, the RJ-45 port becomes active. Baud rates for the USB console port are 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200 bps. Note 4- pin micro USB Type-B connectors are easily confused with 5-pin micro USB Type-B connectors. Only the 5-pin micro USB Type-B is supported. USB Console OS Compatibility Windows 10, Windows 8, Windows 7, Windows 2000, Window XP 32 bit, Windows Vista 32 bit Mac OS X version 10.5.4 Redhat / Fedora Core 10 with kernel 2.6.27.5-117 Ubuntu 8.10 with kernel 2.6.27-11 Debian 5.0 with kernel 2.6 Suse 11.1 with kernel 2.6.27.7-9 Console Port Considerations The router includes an asynchronous serial console port. The console ports provide access to the router using a console terminal connected to the console port. This section discusses important cabling information to consider before connecting the router to a console terminal or modem. Console terminals send data at speeds slower than modems do; therefore, the console port is ideally suited for use with console terminals. Preparing for Network Connections When setting up your router, consider distance limitations and potential electromagnetic interference (EMI) as defined by the applicable local and international regulations. Network connection considerations are provided for:
See the following online document for more information about network connections and interfaces:
Cisco Modular Access Router Cable Specifications Ethernet Connections The IEEE has established Ethernet as standard IEEE 802.3. The routers support the following Ethernet implementations:
1000BASE-T1000 Mb/s full-duplex transmission over a Category 5 or better unshielded twisted-pair
(UTP) cable. Supports the Ethernet maximum length of 328 feet (100 meters). 100BASE-T100 Mb/s full-duplex transmission over a Category 5 or better unshielded twisted-pair
(UTP) cable. Supports the Ethernet maximum length of 328 feet (100 meters). Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 19 Required Tools and Equipment for Installation and Maintenance Prepare for Router Installation 10BASE-T10 Mb/s full-duplex transmission over a Category 5 or better unshielded twisted-pair (UTP) cable. Supports the Ethernet maximum length of 328 feet (100 meters). See the Cisco Modular Access Router Cable Specifications document at Cisco.com for information about Ethernet cables, connectors, and pinouts. RequiredToolsandEquipmentforInstallationandMaintenance You need the following tools and equipment to install and upgrade the router and its components:
ESD-preventive cord and wrist strap Number 2 Phillips screwdriver Phillips screwdrivers: small, 3/16-in. (4 to 5 mm) and medium, 1/4-in. (6 to 7 mm) To install or remove modules To remove the cover, if you are upgrading memory or other components Screws that fit your rack Wire crimper Wire for connecting the chassis to an earth ground:
AWG 14 (2 mm 2 ) or larger wire for NEC-compliant chassis grounding For NEC-compliant grounding, an appropriate user-supplied ring terminal, with an inner diameter of 1/4 in. (5 to 7 mm) Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 20 C H A P T E R 3 Install and Connect the Router This chapter describes how to install and connect Cisco 1100 Series Integrated Services Router (ISR) to LAN and WAN networks. Warning Read the installation instructions before using, installing or connecting the system to the power source. Statement 1004 Installing the Cisco 1100 Series Aggregation Services Routers involve these tasks:
Unpack the Router, on page 21 Set up Router on Desktop, Rack, or Wall, on page 21 Connect Power Cable, on page 31 Connect the Router to a Console, on page 32 Connect WAN and LAN Interfaces, on page 34 Configure the Router at Startup, on page 36 Unpack the Router Unpack the router only when you are ready to install it. If the installation site is not ready, to prevent accidental damage, keep the chassis in its shipping container until you are ready to install. The router, accessory kit, publications, and any optional equipment you order may be shipped in more than one container. When you unpack the containers, check the packing list to ensure that you have received all listed items. Set up Router on Desktop, Rack, or Wall After unpacking, based on your requirements, you can set up a Cisco 1100 Series Integrated Services Routers
(ISRs) on a desktop, a rack, or the wall. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 21 Rack Mount Install and Connect the Router Note You can install external modules before or after mounting a router. However, if you choose to install the external modules after mounting the router on the rack or wall, ensure that you have optimal access to the back/front panel of the router. For information on modules and Field Replaceable Units (FRUs), see the Install and Upgrade Modules and FRUs section. Depending on the model, the available options for mounting a Cisco 1100 ISR are:
Table6:ModelsandMountingOptions Model C111x C1101-4P C1101-4PLTEPWx Mounting Options Desktop, Rack Mount, Wall Mount Using Key-hole Slots, Wall Mount using-Din-Rail Desktop, Wall Mount Using Key-hole Slots Desktop, Wall Mount Using Key-Hole Slots If you choose to setup the router on a desktop, you can place the router on a desktop, bench top, or shelf. Rack Mount The router is shipped with rack mounting brackets that are to be secured on the sides of the chassis. You must first secure rack mounting brackets on the chassis before you set up the chassis on the rack. Note When stacking multiple Cisco 1100 ISRs, ensure that there is ample surrounding space. Ample space, in turn, ensures more heat removal to enable the surrounding air temperature to stay within the specified operating conditions. Attach the Brackets This procedure describes how to attach the brackets on the router chassis:
Step 1 Secure the brackets to the router chassis (on the left) as shown in figure below:
Example:
Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 22 Install and Connect the Router Mount the Router Figure9:BracketInstallationforLeft-SideMounting-C111x Step 2 Similarly, secure the brackets on the right-side of the chassis for mounting the router. Mount the Router Before mounting the router on to the rack, refer to the following safety warning statements:
Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 1.75 in. (4.4 cm). Statement 1076. Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:
This unit should be mounted at the bottom of the rack if it is the only unit in the rack. When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006. To install the router, use the screws provided with the accessory kit to secure the router when you mount it on the rack. Wall Mount Depending on the models of the Cisco 1100 Series Integrated Services Routers (ISRs), the tasks for mounting the router chassis on the wall may vary. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 23 Wall Mount Using Key-hole Slots Install and Connect the Router Note The recommended clearance when a router is horizontally mounted is 1.5 inches on both sides for clearance and 1.75 inches on top. I/O side clearance is needed as it is required to access the cable connections. Clearance is not required on the backside (opposite side from I/O face) unless mounting on a DIN Rail. Clearance is required to attach and mount the DIN rail bracket. There are two ways to mount a router on the wall-Key-hole Slots and DIN Rail Brackets. Wall Mount Using Key-hole Slots The Cisco 1100 Series Integrated Services Routers (ISRs) have key-hole slots at the bottom of the chassis for mounting on a wall or any vertical surface. Note Do not mount the router with the output ports facing downwards. For the C111x series, ensure that the cables are placed on the sides. Note When choosing a location for wall mounting the router, consider cable limitations and wall structure. Note To attach a router to the wall stud, each bracket should have one number10 wood screw (pan-head) with number10 washers, or two number10 washer-head screws. The screws must be long enough to penetrate at least 1.5 inches (38.1 mm) into the supporting wood or metal wall stud. Note For hollow-wall mounting, each bracket requires two wall anchors with washers. Wall anchors and washers must be size number 6 (pan-head). Route the cables so that they do not put a strain on the connectors or mounting hardware. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 24 Install and Connect the Router Wall Mount Using Key-hole Slots Figure10:WallMountUsingKey-holeSlots 1 Key-hole slots Figure11:WallMountOrientation-C111x 1 Key-hole slots Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 25 Wall Mount Using Key-hole Slots Figure12:C1101-4P Install and Connect the Router 1 Key-hole slots Key-hole slots-spacing: 3.024in (76.81mm) Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 26 Install and Connect the Router Wall Mount Using Key-hole Slots Figure13:C1101-4PLTEP 1 Key-hole slots Horizontal spacing: 3.100in (78.74mm) Vertical spacing: 5.758inin (146.25mm) Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 27 Wall Mount Using Key-hole Slots Figure14:C1109-4P Install and Connect the Router 1 Figure15:WallMountOrientation-C1109-4P Key-hole slots Horizontal spacing: 7.302in (185.47mm) Vertical spacing: 7.430in (188.72mm) Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 28 Install and Connect the Router Wall Mount Using DIN Rail Brackets Wall Mount Using DIN Rail Brackets The router is shipped with DIN Rail brackets that are to be secured on the bottom side of the chassis. Your chassis installation must allow unrestricted airflow for chassis cooling. Note Wall mount using DIN Rail brackets is applicable only for C111x. To attach the DIN Rail brackets to the router chassis, use the PHMS screws and the plastic spacers provided for each bracket. Figure16:DINRailBracketInstallation-C111x 1 2 Figure17:OrientationofDINRailBrackets Screws DIN Rail Brackets Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 29 Chassis Grounding Figure18:DINRailBracketsandMount Install and Connect the Router Note Do not over-torque the screws. The recommended torque is 8 to 10 inch-lbf (0.9 to 1.1 N-m). Chassis Grounding After you set up the router, connect the chassis to a reliable earth ground; the ground wire must be installed in accordance with local electrical safety standards. For safety information on grounding the chassis, refer to the chassis ground connection procedures. 1. For grounding the chassis, use size 14 AWG copper wire and the ground lug. These are not a part of the accessory kit. 2. Use the UNC 6-32 screws, which have a length of about 0.25 inches. To install the ground connection for your router, perform these steps:
1. Strip one end of the ground wire to the length required for the ground lug or terminal. For the ground lugapproximately 0.75 inch (20 mm) For user-provided ring terminalas required 2. Crimp the ground wire to the ground lug or ring terminal, using a crimp tool of the appropriate size. 3. Attach the ground lug or ring terminal to the chassis as shown in Figure. The screw for the ground lug is provided. Tighten the screw; the recommended torque is 8 to 10 inch-lbf (0.9 to 1.1 N-m). Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 30 Install and Connect the Router Connect Power Cable Figure19:ChassisGroundConnection-Cisco111x 1 2 Screw (UNC 6-32) Ground Lug Figure20:ChassisGroundConnection-Cisco1101-4PLTEP 1 2 Screw (UNC 6-32) Ground Lug Connect Power Cable Power supply of the Cisco 1100 Series ISRs is an external AC to DC power adapter. The external power adapter DC power connector plugs in to the router 4-pin power connector to power the unit. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 31 Connect the Router to a Console Install and Connect the Router Figure21:PowerCableforUnits-C111xandC1101-4PLTEP Figure22:C111x Figure23:C1101-4PLTEP 1. Power Cable 1. Power Cable Connect the Router to a Console The Cisco 111x Series ISR has an asynchronous serial port. This port provides administrative access to the router through a console terminal or a PC. Use the USB or RJ-45 console port on the router to access the Cisco Internet Operating System (IOS-XE) command line interface (CLI) on the router and perform configuration tasks. A terminal emulation program is required to establish communication between the router and a PC. To configure the router through the Cisco IOS CLI, you must establish a connection between the router console port and either a PC or a terminal. Use the following cables and adapters to establish a local or remote connection. Table7:LocalandRemoteConnections Port Type Cable Section Serial
(RJ-45) C111x: RJ-45 Serial console cable C110x: CAB-CON-USB (Serial USB to RJ-45 serial cable) Connecting to the Serial Port with Microsoft Windows Serial (USB) USB 2.0 Standard-A to USB 2.0 Micro-B cable. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 32 Install and Connect the Router Connect to the Serial Port with Microsoft Windows Connect to the Serial Port with Microsoft Windows To establish a physical connectivity between the router and a PC, you need to install a Microsoft Windows USB. Use the USB Console cable plugged into the USB serial port to establish this connection. 1. Connect the end of the console cable with the RJ-45 connector to the light blue console port on the router. 2. OR Connect a USB 5-pin micro USB Type-B to the USB console port. If you are using the USB serial port for the first time on a Windows-based PC, install the USB driver. Note You cannot use the USB port and the EIA port concurrently. When the USB port is used it takes priority over the RJ-45 EIA port. 3. Connect the end of the cable with the DB-9 connector (or USB Type-A) to the terminal or PC. If your terminal or PC has a console port that does not accommodate a DB-9 connector, you must provide an appropriate adapter for that port. 4. Start a terminal emulator application to communicate with the router. Configure the software with the following parameters:
9600 baud 8 data bits no parity 1 stop bit no flow control Connect to the Console Port with Mac OS X This procedure describes how to connect a Mac OS X system USB port to the console using the built in OS X Terminal utility. Step 1 Step 2 Step 3 Use the Finder to go to Applications > Utilities > Terminal. Connect the OS X USB port to the router. Enter the following commands to find the OS X USB port number Example:
macbook:user$ cd /dev macbook:user$ ls -ltr /dev/*usb*
crw-rw-rw- 1 root wheel 9, 66 Apr 1 16:46 tty.usbmodem1a21 DT-macbook:dev user$
Step 4 Connect to the USB port with the following command followed by the router USB port speed Example:
Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 33 Connect to the Console Port with Linux Install and Connect the Router macbook:user$ screen /dev/tty.usbmodem1a21 9600 To disconnect the OS X USB console from the Terminal window Enter Ctrl-a followed by Ctrl-\
Connect to the Console Port with Linux This procedure shows how to connect a Linux system USB port to the console using the built in Linux Terminal utility. Step 1 Step 2 Step 3 Open the Linux Terminal window. Connect the Linux USB port to the router. Enter the following commands to find the Linux USB port number Example:
root@usb-suse# cd /dev root@usb-suse /dev# ls -ltr *ACM*
1 root crw-r--r--
root@usb-suse /dev#
root 188, 0 Jan 14 18:02 ttyACM0 Step 4 Connect to the USB port with the following command followed by the router USB port speed Example:
root@usb-suse /dev# screen /dev/ttyACM0 9600 To disconnect the Linux USB console from the Terminal window Enter Ctrl-a followed by : then quit Connect WAN and LAN Interfaces This section describes how to connect WAN and LAN interface cables. Before you connect the interface cables, refer to the following warning statements:
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001. Warning Class 1 laser product. Statement 1008. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 34 Install and Connect the Router Ports and Cabling Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026. Caution Compliance with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036. Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037. Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection, LAN, PoE. Statement 1044. Warning Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There may be a risk of electric shock from lightning. Statement 1088. Ports and Cabling This section summarizes typical WAN and LAN connections for Cisco 1100 Series ISRs. The connections summarized here are described in detail in the Cisco Modular Access Router Cable Specifications document on cisco.com. Table8:WANandLANConnections Port or Connection Port Type, Color1 Connection Cable Ethernet RJ-45, yellow Ethernet hub or Ethernet switch Category 5 or higher Ethernet Gigabit Ethernet SFP, optical LC, color according to optical wavelength 1000BASE-SX, -LX, -LH,
-ZX, -CWDM Optical fiber as specified on applicable data sheet Gigabit Ethernet SFP, copper RJ-45 1000BASE-T Category 5, 5e, 6 UTP Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 35 Connection Procedures and Precautions Install and Connect the Router Port or Connection Port Type, Color1 Connection Cable xDSL
(VDSL2 / ADSL2/2+) RJ-11 POTS or ISDN line RJ-11 telephone cable 1 Cable color codes are specific to Cisco cables. Connection Procedures and Precautions After you have installed the router chassis, perform these steps to connect the WAN and LAN interfaces:
Connect each WAN and LAN to the appropriate connector on the chassis. Position the cables carefully so that you do not strain the connectors. Organize cables in bundles so that cables do not intertwine. Inspect the cables to make sure that the routing and bend radius is satisfactory. If necessary, reposition the cables. Install cable ties in accordance with site requirements. Configure the Router at Startup After installing the router and connecting the cables, you can configure the router with basic configurations. For more information on how to configure the router, see the Cisco 1100 Series Software Configuration Guide. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 36 C H A P T E R 4 Install and Upgrade Internal Modules and FRUs The Cisco 1100 Series Integrated Services Routers have internal modules and field-replaceable units (FRUs) that can be quickly and easily removed and replaced without having to send the entire router for repair. This section describes how to install and upgrade the internal modules and FRUs in the Cisco 1100 Series ISRs. The information is contained in the following sections:
Access Internal Modules, on page 37 Locate Internal and External Slots for Modules, on page 39 Remove and Replace the Cisco 1100 Series ISRs Power Supplies , on page 43 Install and Remove SFP Modules, on page 44 Access Internal Modules To access the internal modules on the router, you must first disconnect the power source and then remove the chassis cover. Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Replace the Chassis Cover The Cisco 1100 Series ISRs have a removable cover. Do not attempt to run the router without the cover. This can cause the router to overheat very quickly. To remove the chassis cover, use a number-2 Phillips screwdriver and perform the following tasks:
Remove the Cover To remove the cover, perform the following steps:
Step 1 Step 2 Step 3 Disconnect the power supply before you perform any module replacement. Confirm the router is turned off and disconnected from the power supply or power supplies. If a redundant power is used, disconnect from the redundant power supply. Place the chassis on a flat surface. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 37 Replace the Cover Install and Upgrade Internal Modules and FRUs Step 4 Step 5 Remove all screws on both sides of the router; there are seven screws on each side. Pull the cover to disengage the slots along the front (bezel) edge of the chassis, as shown in this figure. 1 2 Slots Screw holes (7 numbers on each side) Replace the Cover To replace the cover, perform the these steps:
Step 1 Step 2 Step 3 Step 4 Step 5 Disconnect the power supply before you begin replacing the chassis cover. Confirm that the router is turned off and disconnected from the power supply (or power supplies) if there is redundant power supply. Place the chassis on a flat surface. Locate the cover hooks on the mating slots and slide the cover towards the bezel side. Secure seven screws on each side. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 38 Install and Upgrade Internal Modules and FRUs Locate Internal and External Slots for Modules Locate Internal and External Slots for Modules This section describes the location of internal modules on the router motherboard. Internal modules on the Cisco1100 Series ISRs include- An UPoE module and an LTE pluggable module. Figure24:ModuleLocationintheCisco1100SeriesISR 1 PoE Module Install the Universal POE Splitter This section describes how to install the Cisco Universal Power Over Ethernet (UPOE) splitter. The Cisco UPOE splitter (PWR-UPOE-I-SPL) splits UPoE into power and GE The UPOE+ IN connector receives the Ethernet signal pair and 60 W of power from the Cisco UPOE switch, such as the WS-X4748-UPOE+E Ethernet module, and the POE+ OUT connector, in turn, provides the ethernet signal pair to the router. Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Unpack the splitter box and the DC power cord for your router. Position the UPOE splitter box near the PoE slot of the router. Plug one end of a Category 5 TIA-EIA-568-A compliant interface cable into a WS-X4748-UPOE+E Ethernet module port. Connect the other end of the interface cable to the UPOE+ IN connector on the splitter box. Connect a Category 5 TIA-EIA-568-A compliant or a network interface cable between the POE+ OUT port on the splitter box and the router. Attach the appropriate DC power cord between the 12V DC OUT connector on the splitter box and the DC power connector on the router. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 39 LTE Pluggable Module Figure25:UPoESplitter 12V DC PWR LED Install and Upgrade Internal Modules and FRUs YellowOnly the primary pair of UPOE IN connector pins (RJ-45 connector) are receiving power, or the CLI power inline four-pair forced command is not enabled on the UPOE module port. There is no 12 VDC available at the 12V DC OUT connector. GreenBoth the primary and secondary pairs of UPOE IN connector pins are receiving power from the Ethernet module. OffNeither of the pairs of the UPOE connector pins are receiving power. LTE Pluggable Module To install an LTE pluggable module on a Cisco 1100 Series ISR:
Step 1 Step 2 Insert and then gently push the LTE pluggable into the pluggable slot until firmly fixed. Tighten the screw, the recommended torque is 10-12 in-lb. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 40 Install and Upgrade Internal Modules and FRUs LTE Pluggable Module Figure26:LTEPluggable-C1101-4P Item 1 2 3 4 Description GPS Antenna LTE Antenna Ground Lug Keningston Lock Slot Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 41 Install and Upgrade Internal Modules and FRUs Insert a Micro-SIM Card Insert a Micro-SIM Card This section describes how to insert a Micro-SIM card into an LTE pluggable module. Caution Do not touch any part of the exposed PCB circuit area when the Micro-SIM cover is removed. Figure27:InserttheMicro-SIMcards Item 1 2 Description Micro-SIM 1 (Towards the device) Micro-SIM 0 (Away from the device) To insert the Micro-SIM cards into the LTE Pluggable module:
1. Place the router on its bottom side, remove the screws and then the Micro-SIM cover from the pluggable module. 2. Push in each Micro-SIM card into the slot until it clicks. 3. Secure the Micro-SIM cover with a screw. The recommended torque is 2.8 - 3.8 inch LBF. You have now successfully inserted the Micro-SIM cards into the LTE pluggable module. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 42 Install and Upgrade Internal Modules and FRUs Remove and Replace the 1GB Flash Token Memory Stick Remove and Replace the 1GB Flash Token Memory Stick The Cisco 1100 Series ISR has a port for 1 GB flash token memory stick to store configurations or Cisco IOS XE consolidated packages. Note Only Cisco 1GB Flash memory modules are supported on Cisco routers. Caution Do not remove a USB Flash memory module when issuing some file access command or a read or write operation to the Flash memory module when it is processing. Step 1 Step 2 To remove, pull the 1GB flash token memory stick from the USB port. To insert, push the 1GB flash token memory stick into the USB port. The flash memory module can be inserted or removed regardless of whether the router is powered up or not. RemoveandReplacetheCisco1100SeriesISRsPowerSupplies A single 4-pin power connector type shared with 12V main power and -54V PoE supply is used for C111x Series. Single output - 66W +12V power supply for Non-PoE capable units. Dual output - 66W + 12V, 83W -53.5V power supply. 150W power supply for PoE capable units. For all supplies (C1100 Series):
Input - Voltage range is 100 240V AC. Frequency range is 50 60Hz. Output - 12V DC / -54V DC. 30W AC power supply (C1101-4P/C1101-4PLTEPWx Series) A single power connector type is used for Cisco 1100 Series ISR. Connector is capable of conducting 5A. The power connector has a locking mechanism to prevent the connector from being disengaged inadvertently. Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 43 Install and Remove SFP Modules Install and Upgrade Internal Modules and FRUs Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028. Warning Care should be taken while removing the power supplies and power inverters (especially in boost mode of operation). If the total power consumption is higher than can be supported by one power supply alone and in this condition a power supply is removed, the hardware can be damaged. This may then result in the system being unstable or unusable. Install and Remove SFP Modules This section describes how to install optional small-form-factor pluggable (SFP) modules in the router to provide optical Gigabit Ethernet connectivity. The SFP module is installed into a slot on the rear panel of C111x series. Only SFP modules certified by Cisco are supported on these routers. For more information, refer to SFPs Supported on Cisco 1100 ISRs. Note The SFP module-GLC-GE-100FX V01 is not supported on the Cisco 111x Series. Remove the SFP Modules To remove an SFP module from the router:
Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051 Step 1 Step 2 Step 3 Disconnect the power supply before you remove any module. Disconnect all cables from the SFP. Disconnect the SFP latch. Note SFP modules use various latch designs to secure the module in the SFP port. For information on the SFP technology type and model, see the label on the side of the SFP module. Use a pen, screwdriver, or other small straight tool to gently release a bale-clasp handle if you cannot reach it with your fingers. Tip Step 4 Grasp the SFP on both sides and remove it from the router. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 44 C H A P T E R 5 ROM Monitor Overview and Basic Procedures The ROM Monitor (ROMMON) is a bootstrap program that initializes the hardware and boots the Cisco IOS XE software when you power on or reload a router. If your router does not find a valid system image to load when it is booting, the system enters the ROMMON mode. ROMMON mode can also be accessed by interrupting the boot sequence during startup. ROM Monitor Overview, on page 45 ROM Monitor Overview The ROM Monitor software is also known as ROMMON, boot software, boot image, or boot helper. Although it is distributed with routers that use the Cisco IOS XE software, the ROMMON is a separate program from the Cisco IOS XE software. During normal startup, ROMMON initializes the router, and then, the control passes to the Cisco IOS XE software. When you connect a terminal to the router that is in ROMMON mode, the ROMMON command-line interface
(CLI) prompt is displayed. Access the ROMMON mode to perform these tasks:
Specify config-register value to use for the next boot up Boot a valid IOS XE image Bypass NVRAM settings and config-register value for password recovery Note After the Cisco IOS XE software boots up, ROMMON is no longer in use. Environmental Variables and the Configuration Register Two primary connections exist between ROMMON and the Cisco IOS XE software: the ROMMON environment variables and the configuration register. The ROMMON environment variables define the location of the Cisco IOS XE software and describe how to load it. After ROMMON has initialized the router, it uses the environment variables to locate and load the Cisco IOS XE software. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 45 ROM Monitor Overview ROM Monitor Overview and Basic Procedures The configuration register is a software setting that controls how a router starts up. One of the primary uses of the configuration register setting is to control whether the router starts in ROMMON mode or Administration EXEC mode. The configuration register is set in either ROMMON mode or Administration EXEC mode as needed. You can set the configuration register using the Cisco IOS XE software prompt when you need to use ROMMON mode. When maintenance in ROMMODE mode is complete, change the configuration register back so that the router reboots with the Cisco IOS XE software. Access ROMMON Mode with a Terminal Connection When the router is in ROMMODE mode, you can access the ROMMODE software only from a terminal connected directly to the console port of the card. Because the Cisco IOS XE software (EXEC mode) is in operatiion, the nonmanagement interfaces are not accessible. Therefore, all Cisco IOS XE software resources are unavailable. Network Management Access and ROMMON Mode ROMMON mode is a router mode, not a mode within the Cisco IOS XE software. The ROMMON software and the Cisco IOS XE software are two separate programs that run on the same router. At any given time, the router is running one of these programs, but it never runs both at the same time. One area that can be confusing when using ROMMON and the Cisco IOS XE software is the area that defines the IP configuration for the Management Ethernet interface. Most users are comfortable with configuring the Management Ethernet interface in the Cisco IOS XE software. When the router is in ROMMON mode, however, the router is not running the Cisco IOS XE software, therefore, Management Ethernet interface configuration is not available. When you want to access other devices, such as a TFTP server, while in ROMMON mode on the router, you must configure the ROMMON variables with IP access information. For more information on ROMMON and Basic Procedures, refer to the Cisco ISR1000 Software Configuration Guide. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 46 C H A P T E R 6 FCC Supplier Declaration of Conformity This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against any harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may may cause harmful interference to radio communications. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause an undesired operation. The operation of this equipment in a residential area is likely to cause harmful interference, in which case, users are required to correct the interference at their own expense. Radio Compliance This system uses both licensed and licensed exempt radio frequencies. The radios are evaluated to the following regulations:
The Wi-Fi Radio is evaluated to 47 Code of Federal Regulations Part 15.247 and Part 15.407. Part 15 Radio Systems operating outdoors in the 5150-5250 MHz band must comply with the antenna installation requirements as set forth in the FCC Part 15.407 rules. The LTE radio is evaluated to 47 Code of Federal Regulation Part 24 and 27. The LTE radio operates on licensed frequency bands and requires a radio license to operate. It must be operated under the control of a Licensed Service Provider or Wireless Carrier. Modifications by User or Installer Modifying the equipment without Cisco's authorization may result in the equipment being no longer compliant with FCC requirements for Class A digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC RF Exposure Compliance This product has been found to be compliant to the requirements set forth in CFR 47 Section 1.1307 addressing RF Exposure from radio frequency devices, as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 47 FCC Supplier Declaration of Conformity To maintain compliance, the minimum separation distance from the antenna to general bystander is 20 cm
(8,7 inches) or more. CANADA This Class [*] digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe [*] est conforme la norme NMB-003 du Canada Radio (Wi Fi) This product complies with RSS-247 of the Industry Canada Rules. Its operation is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference received, including interference that may cause an undesired operation. Ce dispositif est conforme la norme RSS-247 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:
le dispositif ne doit pas produire de brouillage prjudiciable ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite system. For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz must be such that the equipment still complies with the e.i.r.p. limit. For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz must be such that the equipment still complies with the e.i.r.p. limits as appropriate. For systems that are capable of operating outdoors or with antennas mounted outdoors (where applicable antenna type(s), antenna models(s), and worst-case tilt angle(s)) are necessaryto remain compliant with the e.i.r.p, therefore, the elevation mask requirement set forth in section 6.2.2.3 should be clearly indicated. Radio (Wi Fi) This product complies with the RSS of the Industry Canada rules. Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm (7.87 in.) between the radiator and yourself. Dclaration D'exposition Aux Radiations Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm (7.87 in.) de distance entre la source de rayonnement et votre corps. Hardware Installation Guide for the Cisco 1000 Series Integrated Services Router 48