FCC ID: UDX-60069010 Network Camera

MV2-HW Installation Guide MV2 Overview The Cisco Meraki MV2 is an indoor wireless networked camera that is exceptionally simple to deploy and configure due to its integration into the Meraki dashboard and the use of cloud augmented edge storage. The MV family eliminates the complex and costly servers and video recorders required by traditional solutions which removes the limitations typically placed on video surveillance deployments. Package Contents and Wall Mount Hardware In addition to the MV camera, the following are provided:

MV2 Power Up and Installation Setup Power Options 1 The MV2 can be powered using either the MA-PWR-ETH dongle or the MA-PWR-USB-XX power adapter

(where XX can be -US, -UK, -EU, or -AU). These are optional accessories and ordered separately. The MV2 can be setup either as a table-top orientation or via wall mount. Figure (1) Table Top and Figure

(2) Wall Mount. Once the camera is setup in the desired orientation, the camera head can be adjusted for a customized viewing angle based upon user's preference. Figure (1) -Table Top Figure (2) - Wall Mount 2 Figure (2) - Wall Mount Continued Once the MV2 is setup in the desired orientation. The camera lens can be adjusted to the end-user's viewing preference. 3 Power Options The MV2 can be powered using either the MA-PWR-ETH dongle or the MA-PWR-USB-XX power adapter

(where XX can be -US, -UK, -EU, or -AU). These are optional accessories and ordered separately. Pre-Install Preparation You should complete the following steps before installing the MV2 in its final location. Configure your MV2 in the Networking using Dashboard You should complete the following steps before installing the MV2 in its final location. The following is a brief overview only of the steps required to add a MV2 to your network. For detailed instructions about creating, configuring, and managing Meraki Camera networks, refer to the online documentation (https://documentation.meraki.com/MV). 1. Login to http://dashboard.meraki.com. If this is your first time, create a new account. 2. Find the network to which you plan to add your camera(s) or create a new network. 3. Add your camera(s) to your new network. You will need your Meraki order number (found on your invoice) or the serial number of each camera, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. 4. Verify that the camera is now listed under Cameras > Monitor > Cameras. 4 Check and Configure Firewall Settings If a firewall is in place, it must allow outgoing connections to particular ports using given IP addresses. The most current list of outbound ports and IP addresses for your particular organization can be found here. DNS Configuration Each MV2 will generate a unique domain name to allow for secured direct streaming functionality. These domain names resolve an A record for the private IP address of the camera. Any public recursive DNS server will resolve this domain. If utilizing an onsite DNS server, please whitelist *.devices.meraki.direct or configure a conditional forwarder so that the local domains are not appended to *.devices.meraki.direct and that these domain requests are forwarded to Google public DNS. Assigning IP Addresses At this time, the MV2 does not support static IP assignment. MV2 units must be added to a subnet that uses DHCP and has available DHCP addresses to operate correctly. Installation Instructions Note: Each MV2 comes with an instruction insert within the box. This insert contains detailed step-by-

step guides and images to assist in the physical installation of the camera. A pdf can be found here.

(Notethis is a draft hyperlink not active yet.) Note: During first time setup, the MV2 will automatically update to the latest stable firmware. Some features may be unavailable until this automatic update is completed. This process may take up to 10 minutes due to enabling of whole disk encryption. Wall Mounting Instructions 5 For most mounting scenarios, the MV2 wall mount provides a quick, simple, and flexible means of mounting your device. The installation should be done in a few simple steps Regulatory Statements EU Radiation Exposure Statement FCC Compliance Statement FCC Interference Statement Installing or mounting of this device shall be done as such that a minimum separation distance (distance between a person and the device, or the devices antennas) of 20 cm is always ensured. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 6 FCC Caution Any changes or modifications not expressly approved by Cisco Systems, Inc. could void the users authority to operate this equipment. This Transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11. Industry Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection dautres canaux nest pas possible. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz. Slection dynamique de frquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz. 7

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

Industry Canada Caution Avertissement:

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

Industry Canada Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. D_c_l_a_r_a_t_i_o_n_ _d_e_x_p_o_s_i_t_i_o_n_ _a_u_x_ _r_a_d_i_a_t_i_o_n_s_:

Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. 8 Taiwan Wireless Statements Statement CS-0438 - RoHS RoHS www.cisco.com/go/taiwanrohs Statement CS-0438 - Taiwan RoHS Taiwan RoHS Restricted Substances Content Disclosure Table web address www.cisco.com/go/taiwanrohs 9

ethiafis cisco Model (Modle, #288/215 ): MV2-HW Power (Alimentation, A /SiA):

FCC ID. UDx- 60069010 IC: 69514-60069010 wee Cex ae SSN (N/S): 00X00 R} 217-210019 Sry [7] 0210019217 This device complies with part 15 of the FCC Rules. Oparation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation, EORRIERICRUCOREMOMETT CANHICES (3)/ NWO ()

"Medi in Taiwan, Fabniqu & Tlvan <2 MNb/ EP Cisco Systems, Ine. ( RiSAH/REF 170 West Iosinan Deve Sot Jose, CA 95134 -USA PIN: 600-69010 46mm

Cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134 USA Date: February 9, 2021 Request for Confidentiality Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: UDX-60069010 To Whom It May Concern:

Schematic Diagram Block Diagram Theory of Operation SDR Files SW Security Statement Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments for 180 days. Cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134 USA It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and that information will be available for public review once the grant of equipment authorization is issued. External Photos Internal Photos Test Setup Photos User Manual Best Regards, Aurelio Llabres Compliance Manager, CNGBU Cisco Systems, Inc. Tel: +1 415-432-1000 Fax: +1 415 632-5899

Date: February 9, 2021 FCC ID: UDX-60069010 Declaration for DFS Client Devices We, Cisco Systems, Inc. hereby declare that the device meets all the other requirements specified in Part 15E Section 15.407. If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Sincerely, Aurelio Llabres Compliance Manager, CNGBU Cisco Systems, Inc. Tel: +1 415-432-1000 Fax: +1 415-632-5899 meraki-hw-compliance@cisco.com

Cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134 USA Date: February 5, 2021 Letter of Attestation We, Cisco Systems, Inc. declare the software and all associated drivers for the Meraki MV2

(MV2-HW) will not initiate any transmission on DFS frequencies without initiation by a master. This includes, but is not limited to, restriction on transmissions for beacons and support for Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Letter of Attestation FCC ID: UDX-60069010 To Whom It May Concern:

ad-hoc peer-to-peer modes. Best Regards, Aurelio Llabres Compliance Manager, CNGBU Cisco Systems, Inc. Tel: +1 415-432-1000 Fax: +1 415 632-5899 meraki-hw-compliance@cisco.com

Cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134, USA Power of Attorney Date: 2021/2/24 I hereby have entrusted the following person to be a proxy regarding application for Type Address

: No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. Dear Sir, Certification. Sporton International Inc. Name

: Leo Huang Job Title

: Manager Respectfully, e-mail

: Leohuang@sporton.com.tw I am therefore responsible for the contents of the application. FCC ID: UDX-60069010 Applicants company name

: Cisco Systems, Inc. Applicants company address

: 170 West Tasman Drive, San Jose, CA 95134, USA Signature

Name and Job Title

: Aurelio Llabres / Compliance Manager E-Mail Tel Fax

rllabres@cisco.com

: 1-415-432-1000

: 1-415-632-5899

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Date: February 9, 2021 Subject: declaration of composite/rated equipment for FCC ID: UDX-60069010 To Whom it may concern, We, the undersigned, would like to declare that the composite portion catagorized as Other Class B digital devices & peripherals has been authorized under the Supplier's Declaration of Conformity (SDoC) procedures.

: Cisco Systems, Inc.

: 170 West Tasman Drive San Jose California United States 95134 Sincerely, Applicant Address Signature E-mail Tel.

Name and Job Title.

: Aurelio Llabres, Compliance Manager _________________________________

: meraki-hw-compliance@cisco.com

: 415-432-1000

Cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134, USA TPC Declaration Letter Date: 2021/2/24 We, Cisco Systems, Inc., declare that the device supports the TPC function in final F/W when EUT is sold to FCC IDUDX-60069010 To Whom It May Concern:

FCC market. Respectfully, Applicants company name

: Cisco Systems, Inc. Applicants company address

: 170 West Tasman Drive, San Jose, CA 95134, USA Signature

Name and Job Title

: Aurelio Llabres / Compliance Manager E-Mail Tel Fax

rllabres@cisco.com

: 1-415-432-1000

: 1-415-632-5899