Annex No.5 Technical Description Key: 5WK4 9127 Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49127 FCC ID:KR55WK49127 User Manual of the Siemens VDO Type:
5WK4 9125 5WK4 9126 5WK4 9127 5WK4 9128 Remote Control System I:\POSTZULA\BMW\PL2_TX-ext\Technische_Doku_doc\Func_PL2ext_TX.doc Page 1 of 6 Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49127 FCC ID:KR55WK49127 General description of the RF transmitter PL2 TX The RF remote control system consists of a RF transmitter and a RF receiver mounted within the control unit. The RF transmitter is mechanically integrated in the head of the key. This transmitter is used to transmit an information for locking or unlocking the vehicle by an unidirectional RF transmission line for normal remote operation by pressing a button. In general the following functions are provided:
- Lock the car
- Unlock the car
- Unlock the trunk of the car Power supply The transmitter is provided with 1 Lithium accumulator (VL 2020) that gives a power supply of +3V. Buttons There are three buttons which enable to lock and unlock the doors and to unlock the trunk. During activation, the button is forced to the ground via a pull-up within the microcontroller. Typical usage pattern (for Europe only) 10 lock/unlock operations in 24 hours with typical transmission duration of 2 seconds 0,42 lock/unlock operations with one hour 0.84 3599.16 seconds / hour Transmitter ON Transmitter OFF Duty Cycle: TON / T (ON+OFF) x 100% = 0.84 / 3,600 x 100 % = 0.02%
seconds / hour I:\POSTZULA\BMW\PL2_TX-ext\Technische_Doku_doc\Func_PL2ext_TX.doc Page 2 of 6 Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49127 FCC ID:KR55WK49127 Block diagrams of the transmitter 125 kHz LF Circuit
(L/C) 9,84375 MHz Crystal Button's C for LF communication /
RF - transmittion C reference frequency 616,54kHz Tx, RF data 4,807 kBit/sec PLL Transmitter IC 315 MHz Loop Antenna Power Supply 2,2 to 3,3 V 315 MHz 125 kHz LF Circuit
(L/C) 13,5687 MHz Crystal PLL Transmitter IC 434 MHz Loop Antenna C reference frequency 847,5kHz Tx, RF data 5,3 kBit/sec 434,2 MHz Button's C for LF communication /
RF - transmittion Power Supply 2,2 to 3,3 V I:\POSTZULA\BMW\PL2_TX-ext\Technische_Doku_doc\Func_PL2ext_TX.doc Page 3 of 6 Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49127 FCC ID:KR55WK49127 125 kHz LF Circuit
(L/C) 13,5687 MHz Crystal Button's C for LF communication /
RF - transmittion Power Supply 2,2 to 3,3 V C reference frequency 847,5kHz Tx, RF data 5,3 kBit/sec 868,4 MHz PLL Transmitter IC 868,4 MHz Loop Antenna I:\POSTZULA\BMW\PL2_TX-ext\Technische_Doku_doc\Func_PL2ext_TX.doc Page 4 of 6 Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49127 FCC ID:KR55WK49127 Description 868.4MHz variant for Europe 434.2MHz variant for Europe 315MHz variant for USA 315MHz variant reduced power for Japan Variants Model 5WK4 9125 5WK4 9126 5WK4 9127 5WK4 9128 Technical Data Carrier frequency model 5WK4 9125:
Carrier frequency model 5WK4 9126:
Carrier frequency model 5WK4 9127:
Carrier frequency model 5WK4 9128:
Output power model 5KW4 9125/6/7:
Field strength model 5WK49128:
Type of modulation model 5KW4 9125/6/7:
Type of modulation model 5KW4 9128:
Method of frequency generation:
Number of channels:
Power supply:
- Nominal voltage:
- Lowest voltage:
- Highest voltage:
Type of accumulator:
Transmission range:
Type of RF-antenna:
Length of RF-antenna:
868.4 MHz 0.05%
434.2 MHz 0.05%
315.0 MHz 0.05%
315 MHz 0.05%
< 10 mW
< 500V/m @ 3m FSK ASK PLL 1 accumulator (VL 2020) 3 V 2, 1 V 3, 3 V lithium
<10 m Loop antenna 34 mm I:\POSTZULA\BMW\PL2_TX-ext\Technische_Doku_doc\Func_PL2ext_TX.doc Page 5 of 6 Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49127 FCC ID:KR55WK49127 Label design Europe: (434 MHz) Siemens VDO 5WK4 9126 Japan: (315 MHz) Siemens VDO 5WK4 9128 USA/CAN: (315 MHz) Siemens VDO 5WK49127 IC: 267T-5WK49127 FCC ID:KR55WK49127 Europe: (868 MHz) Siemens VDO 5WK4 9125 This device complies with part 15 of the FCC Rules and RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept interference received, including interference that may cause undesired operation. I:\POSTZULA\BMW\PL2_TX-ext\Technische_Doku_doc\Func_PL2ext_TX.doc Page 6 of 6