FCC ID: KR537924100 Remote Transceiver for Car Access

I BS PG3 CFRF WM Continental AG User Manual of the Continental Radio Frequency Bidirectional Key Fob Type Acura Bidir Fob MY13.5 A2C37924100 I BS PG3 CFRF WM Continental AG GENERAL DESCRIPTION OF THE RF TRANSMITTER The Acura Bidir Fob is a bidirectional RF key designed to provide remote engine start with feedback, remote keyless entry, passive entry, passive engine start, and immobilization functionality. The Acura Bidir Fob has a housing, which may have variants in the pictogram Trunk, alternatively Power-Tail-Gate(PTG):

I BS PG3 CFRF WM Continental AG Feedback on Bidir Fob There exist 3 LEDs for all feedback, at the top of the fob, out of the way of the hand that is holding it. LEFT LED Color : AMBER Function: To show RF communication, or that 2-way communication is taking place. Example: LEFT/AMBER LED flashes 1x in response to a button being pressed when the RF command is sent, and/or it can flash while communicating with the vehicle, or waiting for response (example: while engine is cranking) . Also this LED will blink in response to SMART entry authentication. For other cases, generally the Amber LED should operate in a manner that is respective of the "Base SMART key". CENTER LED Color: GREEN. Function: Used to show positive feedback for a given command. Example: CENTER/GREEN LED is on for 1 second, to provide status feedback for a given operation. It means:

Doors were locked, or engine was started, or engine is ON. RIGHT LED Color: RED. Function: Used to show negative feedback for a given command. There are 2 modes. 1. Out of range. In this case the red LED blinks distinctly 3 times, Example: 3 times in 1 second. It means the fob could not get acknowledgement from the car for 2-way communication, or the vehicle battery is dead and cannot respond. 2. Cannot Lock or Engine not running. In this case the red LED is on for 1 second. Continental AG POWER MANAGEMENT I BS PG3 CFRF WM The Power Supply comprises a coin cell battery CR2032, filter capacitors, diodes, and FETs, that provides power to the microcontroller, the power-

management with charger and the RF circuit. A rechargeable battery (accu) of the type LiFePO4 is included to supply higher currents in case of long range transmission. The accu type LiFePO4 is of the class Li-Ion cell, but with a safe chemistry. There exists a certificate, that it is not dangerous / harmfull in the sense of UN3480 and "Transportation without Class 9 is allowed". I BS PG3 CFRF WM Continental AG 6. TESTMODE FUNCTION The testmode function is only available by EEPROM settings, which could provided only in specially programmed samples for measuring purpose. Button functions Button description D E L d e r ENG.START no function LOCK UNLOCK TRUNK PANIC TX CW Modes X TX Modulated Modes X RX Modes X another inner function X D E L n e e r g X X X D E L r e b m a X X X By pressing the specified button, the previously defined channels are revolving. The Lock button revolves the 8 Channels CW-mode till TX-off TX-LR-CH2, CW-f_low2 TX-LR-CH2, CW-f_high2 3x red LED flash1, TX OFF all LEDs OFF switch to bat-supply, TX ON, TX-SR-CH1, CW-f_low TX-SR-CH1, CW-f_high TX-LR-CH1, CW-f_high2 switch to accu-supply, TX-LR-CH1, CW-f_low2 TX-SR-CH2, CW-f_high TX-SR-CH2, CW-f_low Notes:

1: 3x red flash: 200ms on, 200ms off, 200ms on, 200ms off, 200ms on, off 2: ATIC134 Lite option only Continental AG The Unock button revolves the 4 modulated channels till TX-off I BS PG3 CFRF WM TX-LR-CH2, mod.2 3x red LED flash1, TX OFF all LEDs OFF switch to bat-

supply, TX ON, TX-SR-

CH1, mod. switch to accu-

supply, TX-

LR-CH1, mod. 2 TX-SR-CH2, mod. Notes:

1: 3x red flash: 200ms on, 200ms off, 200ms on, 200ms off, 200ms on, off 2: ATIC134 Lite, test signal data content: zeros The Trunk button revolves the 2 Receive-Channels till RX-off 1x amber LED flash 4x green&red LED flash RX-LR-CH2 3x red LED flash1, RX OFF all LEDs OFF 1x amber LED flash switch to bat-supply, RX ON, 1x green&red LED flash, RX-SR-CH1 1x amber LED flash 3x green&red LED flash, RX-LR-CH1 2x green&red LED flash, RX-SR-CH2 1x amber LED flash Notes:

1: 3x red flash: 200ms on, 200ms off, 200ms on, 200ms off, 200ms on, off Continental AG 7. LABEL DESIGN I BS PG3 CFRF WM CANADA IC:7812D-37924100 USA FCC ID:KR537924100 The print is visible after opening the Fob like for battery change. How to open the Bidir Fob for Battery Change Take a coin (best fit: 2, or a Quarter Dollar), press it into the groove and turn it against the metallic eyelet counterclockwise. For closing follow the instruction:

The device under test is manufactured by the grantee (Continental Automotive GmbH) and sold as an OEM product. Per 47 CFR 2.909, 2.927, 2.931, 2.1033, 15.15(b) etc..., the grantee must ensure the end-user has all applicable / appropriate operating instructions. When end-user instructions are required, as in the case of this product, the grantee must notify the OEM to notify the enduser. Continental Automotive GmbH will supply this document to the reseller/distributor dictating what must be included in the end users manual for the commercial product. INFORMATION TO BE INCLUDED IN THE END USER'S MANUAL The following information (in blue) must be included in the end product users manual to ensure continued FCC and Industry Canada regulatory compliance. The ID numbers must be included in the manual if the device label is not readily accessible to the end user. The compliance paragraphs below must be included in the user's manual.

FCC ID:KR537924100, IC:7812D-37924100 This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s) . Operation is subject to the following two conditions: (1) This device may not caus e harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux C NR d'Industrie Canada applicables aux appareils radio exempts de licence. L'expl oitation est autorise aux deux c onditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilis ateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Note: Changes or modifications not expressively approved by the party responsible for compliance could void the us er's authority to operate the equipment. The term IC: before the radio cert ification number only signifies that Industry Canada technical specifications were met.