WaveLinx Pro Insights Ceiling Sensor
(ECS-Z-M05-LV) Installation Instructions WaveLinx Pro Insights Ceiling Sensor
(ECS-Z-M05-LV) Instructions dinstallation WaveLinx Pro Insights Ceiling Sensor
(ECS-Z-M05-LV) Instrucciones de Instalacin www.cooperlighting.com General Information Overview The WaveLinx Pro Insights ceiling sensor is an integral part of the WaveLinx Pro System and offers Occupant count, Passive Infra-Red (PIR) occupancy sensing, daylighting, temperature, and humidity capability. This sensor has Occupant count and Occupancy coverage patterns of up to 600 square feet, it is low voltage powered and is one of the smartest ceiling mounted sensors for multi-sensing in the market. The sensor operates on a wireless mesh network based on IEEE802.15.4 standards. Plenum rating The WaveLinx Pro Insights ceiling sensor components intended for installation above ceiling are plenum rated. Specifications Compatible only with Cooper Lighting Solutions Lighting WaveLinx Pro Wireless Systems. Power Indicators Environmental Specifications Standards Input power: 120/277VAC Connections: Hot, Neutral LED functionality Indication of wireless network connection Indication of daylight hold-off Operating Temperature Range:
-4F - 131F (-20C - 55C) Storage Temperature Range:
-40F - 158F (-40C - 70C) Relative Humidity: 5% to 95% non-condensing, for indoor use only Listings: UL/cUL Listed, FCC, IC UL244A - Appliance Control /Creepage and Clearance UL 508/NEMA 410 Industrial Control Equipment UL 2043 (Plenum installation) Meets latest ASHRAE Standard 90.1 requirements Meets latest IECC requirements Meets latest CEC Title 24 requirements Wireless Specifications Radio 2.4GHz Standard IEEE 802.15.4 Configuration type Router, End Point Range 75ft (25m) LOS 2 interior walls of standard construction Best practice: 100 devices per Wireless Area Controller Mounting Height 8-12ft (2.4 - 3.7m) WARNING AVERTISSEMENT ADVERTENCIA IMPORTANT: Read carefully before installing product. Retain for future reference. Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and hazards involved. For continued protection against shock hazard replace all covers and guards after field wiring is completed. Risk of Fire and Electric Shock- Before installing or performing any service, the power MUST be turned OFF. All installations should be in compliance with the National Electric Code and all state local codes. Risk of Burn- Disconnect power and allow product to cool before handling or servicing. Risk of Personal Injury- Due to sharp edges, handle with care. Failure to comply with these instructions may result in death, serious bodily injury and property damage. DISCLAIMER OF LIABILITY: Cooper LIghting Solutions assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product. NOTICE: Product may become damaged and/or unstable if not installed properly. Note: Specifications and dimensions subject to change without notice. ATTENTION Receiving Department: Note actual product description of any shortage or noticeable damage on delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days of delivery. All damaged material, complete with original packing must be retained. NOTICE: Designed for indoor installation and use only. Dry location rated. Do not mount near gas or electric heaters. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. The use of accessory equipment is not recommended by Cooper Lighting Solutions as it may cause an unsafe condition. Do not use this equipment for other than the intended use. Warranties and Limitation of Liability Please refer to www.cooperlighting.com for our terms and conditions. English FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Part 15 Clause 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Part 15.19a This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC 2.1093/RSS-102 This product complies with the RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. ISED RSS This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-003(B)/NMB-003(B). Modifications not expressly approved by the manufacturer could void the users authority to operate the equipment under FCC rules. IMPORTANT: Lire attentivement avant dinstaller le luminaire. conserver pour consultation ultrieure. Risque dincendie, de dcharge lectrique, de coupure ou dautres risques Linstallation et lentretien de ce produit doivent tre effectus par un lectricien qualifi. Ce produit doit tre install conformment aux rgles dinstallation en vigueur par une personne familire avec la construction et le fonctionnement du produit ainsi quavec les risques inhrents. Pour une protection continue contre les dcharges lectriques, rinstallez tous les couvercles et protecteurs en place une fois le cblage termin. Risque dincendie et de dcharge lectrique Assurez-vous que lalimentation lectrique est HORS TENSION avant de commencer linstallation ou de tenter den faire lentretien. Mettez lalimentation lectrique hors tension au niveau du fusible ou du disjoncteur. Toutes les installations doivent tre conformes au Code national de llectricit, ainsi qu tous les codes nationaux et locaux. Risque de brlure Dbranchez la source dalimentation et laissez refroidir le luminaire avant de procder son entretien ou sa manipulation. Risque de blessures cause des artes tranchantes, manipulez ce produit avec prcaution. La dsobissance aux instructions suivantes reprsente un risque de blessures (y compris la mort) et de dommages matriels. EXONRATION DE RESPONSABILIT: Cooper LIghting Solutions nassume aucune responsabilit pour les dommages ou pertes de quelque nature que ce soit pouvant dcouler dune installation, dune manipulation ou dune utilisation inapproprie, imprudente ou ngligente de ce produit. AVIS: Ce produit peut sendommager ou devenir instable sil nest pas install correctement. Remarque: Les caractristiques techniques et les dimensions peuvent changer sans pravis. ATTENTION Service de la rception: Veuillez fournir une description de tout lment manquant ou de tout dommage constat au bordereau de rception. Soumettez une rclamation de transporteur public (chargement partiel) directement auprs du transporteur. Les demandes pour les dommages cachs doivent tre prsentes dans les 15 jours suivants la livraison. Tout matriel endommag doit tre conserv avec tout lemballage dorigine. AVIS: Produit conu uniquement pour une installation et un usage lintrieur. Do not mount near gas or electric heaters. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. The use of accessory equipment is not recommended by Cooper Lighting Solutions as it may cause an unsafe condition. Do not use this equipment for other than the intended use. Garanties et limitation de responsabilit Veuillez consulter le site www.cooperlighting.com pour obtenir les conditions gnrales. French nonc de la FCC Remarque: Cet quipement a t mis lessai et dclar conforme aux limites tablies pour un dispositif numrique de catgorie B en vertu de la section 15 des rglements de la FCC. Ces limites sont conues pour assurer une protection raisonnable contre toute interfrence nuisible dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de lnergie radiofrquence et, sil nest pas install et utilis conformment aux instructions, peut provoquer des interfrences nuisibles aux communications radio. Toutefois, il nest absolument pas garanti quaucune interfrence ne se produira dans une installation donne. Si cet quipement provoque des interfrences nuisibles la rception de la radio ou de la tlvision, ce qui peut tre dtermin en teignant et en rallumant lquipement, lutilisateur est encourag essayer de corriger les interfrences par une ou plusieurs des mesures suivantes:
Rorientez ou dplacez lantenne rceptrice. Augmentez la distance entre lquipement et le rcepteur. Branchez lquipement sur la prise lectrique dun circuit autre que celui sur lequel le rcepteur est branch. Demandez de laide au distributeur ou un technicien radio ou TV qualifi. ID du FCC (Commission fdrale des communications des tats-Unis) 15 : Clause 15.21 Tout changement ou modification non expressment approuv par la partie responsable de la conformit pourrait annuler le droit de lutilisateur utiliser lquipement. Ce dispositif est conforme la section 15 des rglements de la FCC. ID du FCC (Commission fdrale des communications des tats-Unis) 15.19a Son fonctionnement est assujetti aux deux conditions suivantes :
1) cet appareil ne doit pas provoquer dinterfrences nuisibles et 2) cet appareil doit accepter toutes les interfrences reues, mme celles qui pourraient provoquer un fonctionnement indsirable. ID du FCC (Commission fdrale des communications des tats-Unis) 2.1093 / RSS-102 Ce produit est conforme la limite dexposition RF dfinie pour un environnement non contrl et est sans danger pour le fonctionnement prvu tel que dcrit dans ce manuel. ISED RSS Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : 1) lappareil ne doit pas produire de brouillage; 2) lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. CAN ICES-003(B)/NMB-003(B). Les modifications non expressment approuves par le fabricant peuvent annuler le droit de lutilisateur faire fonctionner lquipement conformment aux rgles de la FCC. IMPORTANTE: Lea atentamente antes de instalar la luminaria. Conserve estas instrucciones para tenerlas como referencia futura. Riesgo de incendio, descarga elctrica, cortes u otros riesgos de accidentes: la instalacin y el mantenimiento de este producto deben ser realizados por un electricista calificado. Este producto debe ser instalado de acuerdo con el cdigo de instalacin correspondiente por una persona familiarizada con la construccin y la operacin del producto y los peligros involucrados. Para una proteccin continua contra el riesgo de electrocucin, reemplace todas las cubiertas y protectores despus de que se haya completado el cableado de campo. Riesgo de incendio y descarga elctrica: asegrese de que el suministro elctrico est desconectado antes de comenzar la instalacin o intentar realizar cualquier tarea de mantenimiento. Desconecte el suministro elctrico en el fusible o disyuntor. Todas las instalaciones deben cumplir con el Cdigo Elctrico Nacional y todos los cdigos estatales y locales. Riesgo de quemaduras: desconecte el suministro elctrico y espere que la luminaria se enfre antes de manipularla o repararla. Riesgo de lesiones personales: debido a bordes filosos, maniplela con cuidado. El incumplimiento de estas instrucciones puede provocar lesiones graves (incluida la muerte) y daos a la propiedad. RENUNCIA DE RESPONSABILIDAD: Cooper LIghting Solutions no asume ninguna responsabilidad por daos o prdidas de ningn tipo que puedan surgir por la instalacin, manipulacin o uso inadecuado, descuidado o negligente de este producto. AVISO: La luminaria puede daarse y/o ser inestable si no se instala correctamente. Nota: Las especificaciones y dimensiones estn sujetas a cambios sin previo aviso. ATENCIN Departamento de recepcin: Observe que la descripcin real de la luminaria no carezca de piezas ni presente daos notorios al momento de su entrega. Presente el reclamo directamente al transportista de carga (LTL). Los reclamos por daos ocultos deben presentarse dentro de los 15 das posteriores a la entrega. Se debe retener todo el material daado, completo con el embalaje original. AVISO: Diseado solo para su instalacin y uso en interiores. Do not mount near gas or electric heaters. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. The use of accessory equipment is not recommended by Cooper Lighting Solutions as it may cause an unsafe condition. Do not use this equipment for other than the intended use. Garantas y Limitacin de Responsabilidad Visite www.cooperlighting.com para conocer nuestros trminos y condiciones. Spanish Declaracin de la FCC Nota: El equipo ha sido probado y cumple con los lmites para un dispositivo digital de Clase B, de conformidad con la parte 15 de las Normas de la FCC. Estos lmites estn diseados para proporcionar una proteccin razonable contra las interferencias dainas en una instalacin residencial. Este equipo genera, usos y puede emitir energa de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencia daina en las comunicaciones de radio. Sin embargo, no se puede garantizar que dicha interferencia no ocurra en una instalacin determinada. Si este equipo causa interferencia daina en la recepcin de radio o televisin, lo que puede determinarse apagando y encendiendo el equipo, se recomienda al usuario que intente corregir la interferencia mediante una o ms de las siguientes medidas:
Reorientar o reubicar la antena receptora. Aumentar la separacin entre el equipo y el receptor. Conectar el equipo a una toma de corriente en un circuito diferente al que est conectado el receptor Consultar con el distribuidor o con un tcnico de radio/TV experimentado para obtener ayuda. Declaracin de la FCC parte 15 clusula 15.21 Los cambios o modificaciones no aprobados expresamente por la parte responsable del cumplimiento podran anular la autoridad del usuario para operar el equipo. Declaracin de la FCC parte 15.19a Este dispositivo cumple con la parte 15 de las Reglas de la FCC. El funcionamiento est sujeto a las siguientes dos condiciones: (1) este dispositivo no puede causar interferencias perjudiciales, y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluidas las interferencias que puedan causar un funcionamiento no deseado. Declaracin de la FCC parte 2.1093 / RSS102 Este producto cumple con el lmite de exposicin a RF establecido para un entorno no controlado y es seguro para el funcionamiento previsto como se describe en este manual. ISED RSS Este dispositivo cumple con los RSS exentos de licencia de Industry Canada. El funcionamiento est sujeto a las dos condiciones siguientes: (1) Este dispositivo no puede causar interferencias; y (2) Este dispositivo debe aceptar cualquier interferencia, incluida la interferencia que pueda causar un funcionamiento no deseado del dispositivo. CAN ICES-3 (B) / NMB-3 (B). Las modificaciones no aprobadas expresamente por el fabricante podran anular la autoridad del usuario para operar el equipo segn las normas de la FCC. Wiring The unit is powered by a 24VDC power supply. Please make sure the correct polarity is used for the power supply connections. 6 WaveLinx Pro Insights Sensors connected to 1 power supply Surface Mount / J-Box installation 1. Attach junction box adapter plate to 4 (101.6mm) square junction box.
(screws not included) 2. Align sensor with keyhole pattern. 3. The Wireless Sensor may be installed directly to a ceiling surface via a 4 (101.6mm) square junction box adapter plate. Single Sensor Setup 1. The imaginary + made with the vent holes and LEDs should be approximately perpendicular with walls when possible. Imaginary + made with the vent holes and LED Multi Sensor Camera Orientation All cameras oriented the SAME direction 24 Volt Power Supply
4 (101.6mm) square junction box adapter plate Insights Ceiling Sensor Installation There are various methods that may be used to affix the Wavelinx Insights Sensor to a ceiling surface. Tilemount installation 1. Cut 3.8 (95.3mm) diameter hole in ceiling tile. 2. Snap sensor body into ceiling trim. 3. Torsion spring clips secure the Insights Sensor to a recessed ceiling tile. ceiling tile 1 2 ceiling tile 3 room walls Single camera room CORRECT orientation Single camera room INCORRECT orientation conference room walls All cameras oriented DIFFERENT directions LED and Button Definitions One press and release will reboot the unit Press and release 6 times, for 5 seconds each, for a factory reset Sensor Status LED Indication while in out-of-box mode There are two LED indicators on this sensor, one positioned above the camera lens (People count sensor status LED or BLE LED), and one on the other side below the reset button (Zigbee LED). On power up Zigbee LED blink momentarily in red and once after that it will blink green on detecting occupancy/motion. BLE LED/Occupant Count LED momentarily in Amber and will remain OFF until sensor is claimed to WAC and registered under license. Reset button to enable pairing mode On power up the sensor will not be in pairing mode, it requires two-time power cycle or IR remote command or press the reset button two times (equivalent to power cycle) to get the sensor to pairing mode to get join a WAC which is in pairing/commissioning mode. Out-of-box functionality As Insights CS is a ceiling sensor without own light fixture associated to it there is no user functionality before it is added to the WAC. Troubleshooting There are no user-serviceable parts inside of the Sensor Interface Module. Please return the device to Cooper Lighting Solutions if service is required. The device is ONLY intended for use with WAC and Trellix releases of SR9 and beyond? (If the device is claimed to a WAC prior to SR9, it will not be represented correctly and Occupany Counting will not work unless it is completely reset after the WAC is upgraded to SR9 or later.) NEED to re-word this. If still having trouble, call Technical Services at 1-800-553-3879. English conference room walls longer dimension Cooper Lighting Solutions 1121 Highway 74 South Peachtree City, GA 30269 www.cooperlighting.com For service or technical assistance:
1-800-553-3879 Canada Sales 5925 McLaughlin Road Mississauga, Ontario L5R 1B8 P: 905-501-3000 F: 905-501-3172 2022 Cooper Lighting Solutions All Rights Reserved Printed in Mexico Publication No. IL50372722 August 2022 Cooper Lighting Solutions is a registered trademark. All trademarks are property of their respective owners. Product availability, specifications, and compliances are subject to change without notice. room walls room walls Multi Sensor Setup 1. The imaginary + made with the vent holes and LEDs should be approximately perpendicular with the walls when possible 2. The lens as a reference point should be facing the same way in all those included in a multi-sensor setup 3. Best practice for rectangular rooms: The camera side of the sensor should point at one of the longer walls of the room, and as previously mentioned, the two cameras should both point the same direction. See image below Sensor 1 Sensor 2 overlap area shorter dimension Installation Notes Consult www.cooperlighting.com for the most up-to-date revision of the Insights Ceiling system design guide and install this product according to the guidelines described. The Sensor is to be installed in dry, indoor locations ONLY. Do not install the Sensor in damp locations. Damp locations are defined as: interior locations subject to moderate degrees of moisture, such as some basements, some barns, some cold-storage warehouses, and the like, and partially protected locations under canopies, marquees, roofed open porches, and the like. Camera and Sensor Location Notes The Sensor provides 360 coverage pattern. It is recommended to install the sensor more than 4ft (1.2m) away from air supply vents. General Information Vue densemble The WaveLinx Pro Insights ceiling sensor is an integral part of the WaveLinx Pro System and offers Occupant count, Passive Infra-Red (PIR) occupancy sensing, daylighting, temperature, and humidity capability. This sensor has Occupant count and Occupancy coverage patterns of up to 600 square feet, it is low voltage powered and is one of the smartest ceiling mounted sensors for multi-sensing in the market. The sensor operates on a wireless mesh network based on IEEE802.15.4 standards. Caractristiques nominales du plnum The WaveLinx Pro Insights ceiling sensor components intended for installation above ceiling are plenum rated. Spcifications Compatible only with Cooper Lighting Solutions Lighting WaveLinx Pro Wireless Systems. Alimentation Indicateurs Spcifications environnementales Normes Sans fil Spcifications Puissance dentre : 120/277 VCA Connexions : Charg, neutre Fonctionnalit DEL Indication de la connexion au rseau sans fil Indication de blocage de lumire du jour Plage de temprature de fonctionnement :
-20C 55C (-4F 131F) Plage de temprature de stockage :
-40C 70C (-40F 158F) Humidit relative : 5% 95% sans condensation, pour usage intrieur uniquement Caractristiques nominales : Homologu UL/cUL, FCC, IC UL244A Commande dappareil/sels grimpants et espace UL508/NEMA410 quipement de commande industriel UL2043 (installation de plnum) Rpond aux exigences de la norme90.1 de la ASHRAE Rpond aux exigences de la IECC Rpond aux exigences du chapitre24 de la CEC Radio 2,4GHz Protocole IEEE802.15.4 Configuration de type routeur, point limite Porte de perte de signal de 25m (75pi) 2 murs intrieurs dune construction standard Meilleure pratique : 100 dispositifs par contrleur de zone sans fil Hauteur de montage 8-12ft (2.4 - 3.7m) General Information Descripcin General The WaveLinx Pro Insights ceiling sensor is an integral part of the WaveLinx Pro System and offers Occupant count, Passive Infra-Red (PIR) occupancy sensing, daylighting, temperature, and humidity capability. This sensor has Occupant count and Occupancy coverage patterns of up to 600 square feet, it is low voltage powered and is one of the smartest ceiling mounted sensors for multi-sensing in the market. The sensor operates on a wireless mesh network based on IEEE802.15.4 standards. Plenum rating The WaveLinx Pro Insights ceiling sensor components intended for installation above ceiling are plenum rated. Especificaciones Compatible only with Cooper Lighting Solutions Lighting WaveLinx Pro Wireless Systems. Corriente Indicadores Especificaciones ambientales Estndares Dispositivo i nalmbrico Especificaciones Corriente de entrada: 120/277 VCA Conexiones: Caliente, neutro Funcionalidad LED Indicacin de conexin a la red inalmbrica Indicacin de retraso de la luz del da Rango de temperatura de funcionamiento:
-4F - 131F (-20C - 55C) Rango de temperatura de almacenamiento:
-40F - 158F (-40C - 70C) Humedad relativa: 5% a 95% sin condensacin, solo para uso en interiores. Listados: Listado UL/cUL, FCC, IC UL244A - Control de dispositivo /lneas de fuga y distancia en el aire Equipo de control industrial UL 508/NEMA 410 UL 2043 (instalacin plenum) Cumple con los requisitos del estndar 90.1 de ASHRAE Cumple con los requisitos de IECC Cumple con los requisitos del Ttulo 24 de CEC Radio 2,4GHz Estndar IEEE 802.15.4 Tipo de configuracin Enrutador, Nodo final Alcance 75 pies (25 m) LOS 2 paredes interiores de construccin estndar. Mejores prcticas: 100 dispositivos por controlador de rea inalmbrico Altura de montaje 8-12ft (2.4 - 3.7m) 24 Volt Power Supply
1 2 24 Volt Power Supply
1 2 Wiring The unit is powered by a 24VDC power supply. Please make sure the correct polarity is used for the power supply connections. 6 WaveLinx Pro Insights Sensors connected to 1 power supply Surface Mount / J-Box installation 1. Attach junction box adapter plate to 4 (101.6mm) square junction box.
(screws not included) 2. Align sensor with keyhole pattern. 3. The Wireless Sensor may be installed directly to a ceiling surface via a 4 (101.6mm) square junction box adapter plate. Camera and Sensor Location Notes The Sensor provides 360 coverage pattern. It is recommended to install the sensor more than 4ft (1.2m) away from air supply vents. Multi Sensor Camera Orientation All cameras oriented the SAME direction Single Sensor Setup 1. The imaginary + made with the vent holes and LEDs should be approximately perpendicular with walls when possible. Imaginary + made with the vent holes and LED Insights Ceiling Sensor Installation There are various methods that may be used to affix the Wavelinx Insights Sensor to a ceiling surface. Tilemount installation 1. Cut 3.8 (95.3mm) diameter hole in ceiling tile. 2. Snap sensor body into ceiling trim. 3. Torsion spring clips secure the Insights Sensor to a recessed ceiling tile. carreau de plafond carreau de plafond room walls Single camera room CORRECT orientation Single camera room INCORRECT orientation conference room walls All cameras oriented DIFFERENT directions room walls room walls conference room walls Installation Notes Consult www.cooperlighting.com for the most up-to-date revision of the Insights Ceiling system design guide and install this product according to the guidelines described. The Sensor is to be installed in dry, indoor locations ONLY. Do not install the Sensor in damp locations. Damp locations are defined as: interior locations subject to moderate degrees of moisture, such as some basements, some barns, some cold-storage warehouses, and the like, and partially protected locations under canopies, marquees, roofed open porches, and the like. Multi Sensor Setup 1. The imaginary + made with the vent holes and LEDs should be approximately perpendicular with the walls when possible 2. The lens as a reference point should be facing the same way in all those included in a multi-sensor setup 3. Best practice for rectangular rooms: The camera side of the sensor should point at one of the longer walls of the room, and as previously mentioned, the two cameras should both point the same direction. See image below Sensor 1 Sensor 2 overlap area shorter dimension longer dimension Cooper Lighting Solutions 1121 Highway 74 South Peachtree City, GA 30269 www.cooperlighting.com Pour obtenir de laide technique ou un service:
1800553-3879 Service des ventes du Canada 5925 McLaughlin Road Mississauga (Ontario) L5R 1B8 Tl.: 905501-3000 Tlc.: 905501-3172 Cooper Lighting Solutions, 2022. Tous droits rservs. Imprim en Mexique Publication no IL50372722 Aout 2022 Cooper Lighting Solutions est une marque dpose. Toutes les autres marques de commerce sont la proprit de leur propritaire respectif. La disponibilit du produit, les spcifications et les conformits peuvent tre modifies sans pravis. Wiring The unit is powered by a 24VDC power supply. Please make sure the correct polarity is used for the power supply connections. 6 WaveLinx Pro Insights Sensors connected to 1 power supply Surface Mount / J-Box installation 1. Attach junction box adapter plate to 4 (101.6mm) square junction box.
(screws not included) 2. Align sensor with keyhole pattern. 3. The Wireless Sensor may be installed directly to a ceiling surface via a 4 (101.6mm) square junction box adapter plate. Camera and Sensor Location Notes The Sensor provides 360 coverage pattern. It is recommended to install the sensor more than 4ft (1.2m) away from air supply vents. Multi Sensor Camera Orientation All cameras oriented the SAME direction Single Sensor Setup 1. The imaginary + made with the vent holes and LEDs should be approximately perpendicular with walls when possible. Imaginary + made with the vent holes and LED room walls Single camera room CORRECT orientation Single camera room INCORRECT orientation conference room walls All cameras oriented DIFFERENT directions Insights Ceiling Sensor Installation There are various methods that may be used to affix the Wavelinx Insights Sensor to a ceiling surface. Tilemount installation 1. Cut 3.8 (95.3mm) diameter hole in ceiling tile. 2. Snap sensor body into ceiling trim. 3. Torsion spring clips secure the Insights Sensor to a recessed ceiling tile. placa del cielo raso placa del cielo raso room walls room walls conference room walls Installation Notes Consult www.cooperlighting.com for the most up-to-date revision of the Insights Ceiling system design guide and install this product according to the guidelines described. The Sensor is to be installed in dry, indoor locations ONLY. Do not install the Sensor in damp locations. Damp locations are defined as: interior locations subject to moderate degrees of moisture, such as some basements, some barns, some cold-storage warehouses, and the like, and partially protected locations under canopies, marquees, roofed open porches, and the like. Multi Sensor Setup 1. The imaginary + made with the vent holes and LEDs should be approximately perpendicular with the walls when possible 2. The lens as a reference point should be facing the same way in all those included in a multi-sensor setup 3. Best practice for rectangular rooms: The camera side of the sensor should point at one of the longer walls of the room, and as previously mentioned, the two cameras should both point the same direction. See image below Sensor 1 Sensor 2 overlap area shorter dimension longer dimension Cooper Lighting Solutions 1121 Highway 74 South Peachtree City, GA 30269 www.cooperlighting.com Para servicio o asistencia tcnica:
1-800-553-3879 Servicio de ventas de Canada 5925 McLaughlin Road Mississauga (Ontario) L5R 1B8 T: 905501-3000 T: 905501-3172 2022 Cooper Lighting Solutions Todos los derechos reservados Impreso en Mxico Publicacin No.IL50372722 Agosto 2022 Cooper Lighting Solutions es una marca registrada. Todas las marcas registradas son propiedad de sus respectivos propietarios. La disponibilidad de productos, las especificaciones y los cumplimientos estn sujetos a cambio sin previo aviso. LED and Button Definitions One press and release will reboot the unit Press and release 6 times, for 5 seconds each, for a factory reset Sensor Status LED Indication while in out-of-box mode There are two LED indicators on this sensor, one positioned above the camera lens (People count sensor status LED or BLE LED), and one on the other side below the reset button (Zigbee LED). On power up Zigbee LED blink momentarily in red and once after that it will blink green on detecting occupancy/motion. BLE LED/Occupant Count LED momentarily in Amber and will remain OFF until sensor is claimed to WAC and registered under license. Reset button to enable pairing mode On power up the sensor will not be in pairing mode, it requires two-time power cycle or IR remote command or press the reset button two times (equivalent to power cycle) to get the sensor to pairing mode to get join a WAC which is in pairing/commissioning mode. Out-of-box functionality As Insights CS is a ceiling sensor without own light fixture associated to it there is no user functionality before it is added to the WAC. Troubleshooting There are no user-serviceable parts inside of the Sensor Interface Module. Please return the device to Cooper Lighting Solutions if service is required. The device is ONLY intended for use with WAC and Trellix releases of SR9 and beyond? (If the device is claimed to a WAC prior to SR9, it will not be represented correctly and Occupany Counting will not work unless it is completely reset after the WAC is upgraded to SR9 or later.) If still having trouble, call Technical Services at 1-800-553-3879. LED and Button Definitions One press and release will reboot the unit Press and release 6 times, for 5 seconds each, for a factory reset Sensor Status LED Indication while in out-of-box mode There are two LED indicators on this sensor, one positioned above the camera lens (People count sensor status LED or BLE LED), and one on the other side below the reset button (Zigbee LED). On power up Zigbee LED blink momentarily in red and once after that it will blink green on detecting occupancy/motion. BLE LED/Occupant Count LED momentarily in Amber and will remain OFF until sensor is claimed to WAC and registered under license. Reset button to enable pairing mode On power up the sensor will not be in pairing mode, it requires two-time power cycle or IR remote command or press the reset button two times (equivalent to power cycle) to get the sensor to pairing mode to get join a WAC which is in pairing/commissioning mode. Out-of-box functionality As Insights CS is a ceiling sensor without own light fixture associated to it there is no user functionality before it is added to the WAC. Troubleshooting There are no user-serviceable parts inside of the Sensor Interface Module. Please return the device to Cooper Lighting Solutions if service is required. The device is ONLY intended for use with WAC and Trellix releases of SR9 and beyond? (If the device is claimed to a WAC prior to SR9, it will not be represented correctly and Occupany Counting will not work unless it is completely reset after the WAC is upgraded to SR9 or later.) If still having trouble, call Technical Services at 1-800-553-3879. French Spanish 4 (101.6mm) square junction box adapter plate 4 (101.6mm) square junction box adapter plate 3 3