all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Users Manual | Users Manual | 1.14 MiB | December 20 2018 / June 18 2019 | |||
1 2 |
|
Internal Photos | Internal Photos | 1.61 MiB | December 20 2018 / June 18 2019 | |||
1 2 |
|
External Photos | External Photos | 597.76 KiB | December 20 2018 / June 18 2019 | |||
1 2 |
|
Label | ID Label/Location Info | 52.74 KiB | ||||
1 2 |
|
Authorization Letter | Cover Letter(s) | 46.95 KiB | December 20 2018 | |||
1 2 | Block Diagram | Block Diagram | December 20 2018 | confidential | ||||
1 2 |
|
Confidentiality Letter | Cover Letter(s) | 43.23 KiB | December 20 2018 | |||
1 2 | Operational Description | Operational Description | December 20 2018 | confidential | ||||
1 2 | Schematics | Schematics | December 20 2018 | confidential | ||||
1 2 | Test Setup Photos | December 20 2018 / June 18 2019 | ||||||
1 2 | Test Report | December 20 2018 | ||||||
1 2 | RF Exposure Info | December 20 2018 | ||||||
1 2 | Schematic | Schematics | December 20 2018 | confidential |
1 2 | Users Manual | Users Manual | 1.14 MiB | December 20 2018 / June 18 2019 |
SXFI AIR Super X-Fi Bluetooth Headphones Overview 4 5 6 7 8 Enhance Your Audio Power Button Super X-FI Button Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Built-in Battery Charging SXFI Air when it is switched off Built-in LED will blink in Green every 2 secs Built-in LED will turn off when fully charged 3 2 1 RGB Lighting:
Blue OR Users Color Setting Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low Bluetooth / Source Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Solid Green 10 9 Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference SOUR C E Note:
Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C Port 10. 3.5mm Analog Jack Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Model No. / / : EF0810 PN: 03EF081000000 REV A Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH
(4.81Wh) Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app Other Information Supplementary documentation for this product includes a detailed user guide, DoC and safety and regulatory information. These documents can be downloaded from the creative.com/support/SXFI Air site. Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Note:
Mobile app is required to establish BLE connection BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note:
Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Blue-
tooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources RGB Lighting:
Blinks in Blue when in Pairing Mode Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth:
Bluetooth will auto connect to last paired device when switched on Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink twice in Red RGB Lighting will revert to default color once Bluetooth Reset is complete Voice Prompt:
Bluetooth Reset Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track Call Panning:
Activate Call Panning function by swiping Left/Right. Default Call Direction: Center Cycle Sequence (Left Swipe):
Right > Center > Left Cycle Sequence (Right Swipe):
Left > Center > Right Initiate Voice Assistant:
Tap and hold for 2 secs to initiate voice assistant Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback The Bluetooth word mark and logo are owned by the Bluetooth SIG, Inc. and any use of such marks by Creative Technology Ltd. and its affiliates is under license. 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C-Anschluss 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode DE Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app Weitere Informationen Die Zusatzinformationen zu diesem Produkt bestehen aus einem detaillierten Benutzerhandbuch, DoC sowie Sicherheits- und Bestimmungsangaben. Diese Dokumente sind auf der Website creative. com/support/SXFI Air als Download verfgbar. Bewahren Sie dieses Dokument zur spteren Referenz auf. Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off ES Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app Otra informacin La documentacin complementaria para este producto incluye una gua del usuario detallada, as como una declaracin de conformidad (DoC) e informacin sobre normativa y seguridad. Estos documentos se pueden descargar en el sitio creative.com/support/SXFI Air. Guarde este documento para futuras consultas. Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off IT Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app Altre informazioni La documentazione aggiuntiva per questo prodotto include una dettagliata guida utente, DoC e informazioni e normative sulla sicurezza. I documenti possono essere scaricati dal sito creative.com/
support/SXFI Air. Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C Port 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green FR Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off 2018 Creative Labs Pte. Ltd. All rights reserved. Creative, the Creative logo, X-FI, SXFI and the Super X-Fi logo are trademarks or registered trademarks of Creative Technology Ltd in the United States and/or other countries. All other trademarks are the property of their respective owners and are hereby recognized as such. All specifications are subject to change without notice. Use of this product is subject to a limited hardware warranty. Actual contents may differ slightly from those pictured. 2018 Creative Labs Pte. Ltd. Tous droits rservs. Creative, le logo Creative, X-FI, SXFI et le logo Super X-Fi sont des marques ou des marques dposes de Creative Technology Ltd. aux tats-Unis et/ou dans les autres pays. Toutes les autres marques appartiennent leurs propritaires respectifs. Toutes les spcifications peuvent faire lobjet de modifications sans pravis. Lutilisation de ce produit est soumise une garantie limite sur le matriel. Le contenu rel peut lgrement diffrer de celui prsent. 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right RU Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app
, (DoC),
. - creative.com/support/
SXFI Air site. . Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. Puerto USB-C 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. Porta USB-C 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Other information Les documents supplmentaires concernant ce produit incluent un guide de lutilisateur dtaill, la DoC, ainsi que des informations rglementaires et lies la scurit. Ils peuvent tre tlchargs sur le site creative.com/support/SXFI Air. Conservez ce document pour pouvoir vous y rfrer ultrieurement. Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Shuffle Mode:
Tap once to shuffle Voice Prompt:
Shuffle On Shuffle Off Note:
Only applicable to Micro SD card playback Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C Port 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C Port 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C Port 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode CZ Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app Dal informace Dodaten dokumentace k tomuto vrobku zahrnuje podrobnou uivatelskou pruku, dokumenty
(DoC) a informace o bezpenosti a souladu s pedpisy. Tyto dokumenty lze sthnout na adrese creative.com/support/SXFI Air. Tento dokument si ponechejte pro pozdj pouit. Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting KO Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C 10. 3.5mm Analog Jack Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app
, ,
. creative.com/support/SXFI Air . Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off Bluetooth / Source Button SOUR C E Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off PL Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app Inne informacje Dokumentacja uzupeniajca dla tego produktu zawiera szczegow instrukcj dla uytkownika, certyfikat zgodnoci (DoC) oraz informacje na temat bezpieczestwa i przepisw prawnych. Doku-
mentacj mona pobra z witryny pod adresem creative.com/support/SXFI Air. Niniejszy dokument naley zachowa na przyszo. Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting CS Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app DoC creative. com/support/SXFI Air Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off 6. Bluetooth / Source Button 7. Power Button 8. NanoBoom Mic 9. USB-C 10. 3.5mm Analog Jack SOUR C E Bluetooth / Source Button Bluetooth Pairing:
Press and hold for 2 secs to initiate Bluetooth pairing Press and hold for 2 secs again to cancel Voice Prompt:
Now In Pairing Mode Connecting/Disconnecting Bluetooth Bluetooth will auto connect to last paired device when switched on RGB Lighting:
Blinks in Blue when in Pairing Mode SK Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app alie informcie alia dokumentcia pre tento vrobok obsahuje podrobn nvod na obsluhu, DOC a informcie o bezpenosti a prvnych predpisov. Tieto dokumenty si mete prevzia z lokality creative.com/
support/SXFI Air. Tento dokument uschovajte na budce pouitie. Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off JP Overview 1. RGB Lighting 2. High Density Memory Foam 3. Durable Hybrid Headband 4. Super X-FI Button 5. SD Card Slot Specification Headphones Driver: 50mm Neodymium magnet Frequency response: 20 Hz ~ 20 kHz Impedance: 32 Sensitivity: 105 dB/mW @ 1 kHz USB input: 5 V Microphone Type: Unidirectional noise-reduction Frequency response: 50 Hz ~ 15 kHz Impedance: <2.2 k Sensitivity: -42 dB @ 1 kHz Wireless Type: Bluetooth 4.2 Bluetooth Profiles:
A2DP (Wireless stereo Bluetooth) AVRCP (Bluetooth remote control) HFP (Hands-free profile) Input: 5V 1A RF Output Power: < 4dBm Operating temperature: 0C to 45C Wireless Range: Up to 10m Charging Time: 2.5hr Play Time: Up to 8hr playback time Audio Codec: SBC Lithium Ion Battery: 3.7V 1300mAH (4.81Wh) Enhance your audio Unleash the performance of Super X-Fi with the SXFI App and SXFI Control App Charging Charging SXFI Air when it is switched off
- Built-in LED will blink in Green every 2 secs
- Built-in LED will turn off when fully charged Voice Prompt:
- Battery Level Low
- Battery Level Medium
- Battery Level High Note:
RGB Lighting will light up and indicate Battery Level when switched on When battery is low, headphones will prompt Battery Level Low every 10 minutes Headphones will not switch on when battery is too low Turns off automatically after 10 minutes of inactivity in the following modes: Bluetooth / Line-in /
SD Card. Headphones will start charging when connected via USB to a power source except in the following modes: USB Mode / Mass Storage Mode Battery Level is also indicated in app for users reference Factory Reset 1. Press and Button simultaneously for 5 secs till RGB Lighting blink twice in Red 2. RGB Lighting will revert to default color once Factory Reset is complete Voice Prompt: Reset to Factory Default Note: Factory Reset can also be triggered via Windows app jp.creative.com/support Compliance markings can be seen on the surface upon removal of ear cup cushion which can be removed by hand. Keep this document for future reference. Power Button Power Button:
Press and hold for 2 secs to switch on Press and hold for 2 secs again to switch off Press and hold shortly to indicate battery level. RGB Lighting will blink twice in Red in off mode if battery level is low RGB Lighting:
Blue OR Users Color Setting Bluetooth Reset:
Press and hold for 8 secs till the RGB Lighting blink RGB Lighting will revert to default color once twice in Red Bluetooth Reset is complete Note: Bluetooth will cancel discovery mode if no device is paired within 30 secs. Bluetooth can only be paired in standalone state Voice Prompt:
Bluetooth Reset BLE Pairing:
Trigger pairing on mobile app Press and hold Bluetooth Pairing for 2 secs Note:
Mobile app is required to establish BLE connection Change Sources:
Press once to switch between sources (Bluetooth > Micro SD Card > USB Audio) Voice Prompt:
- Bluetooth
- SD Card
- USB Note: Limited to Bluetooth / Line-in / Micro SD source in Standalone mode only. When in USB mode, Bluetooth Low Energy will activate. Nintendo Switch works with Line-in mixed with other sources Super X-Fi Button Enabling Super X-FI:
Press once to activate SXFI Press once again to deactivate SXFI Recovery Mode:
Press and hold Super X-Fi button before powering up the headphones RGB Lighting:
Blink once in Green when activated Blink once again in Orange when deactivated RGB Lighting:
Solid Green Touch Pad Increase Volume:
Headphones will play a tone at Maximum Volume Decrease Volume Previous Track Next Track swiping Left/Right. Call Panning:
Activate Call Panning function by Default Call Direction: Center Cycle Sequence (Left Swipe):
Cycle Sequence (Right Swipe):
Right > Center > Left Left > Center > Right voice assistant Initiate Voice Assistant:
Tap and hold for 2 secs to initiate Incoming Call:
Tap twice to answer incoming call Tap twice again to end call Initiate Playback:
Tap twice to initiate playback Tap twice again to pause playback Mass Storage Mode:
Tap and hold for 4 secs to enter Mass Storage mode Tap and hold for 4 secs again to exit Mass Storage mode Note:
Switching on/off Mass Storage mode takes 15 secs. 2 short beeps will play when switching on/off. Shuffle Mode: Tap once to shuffle Voice Prompt:
Shuffle On Note: Only applicable to Micro SD card playback Shuffle Off EN FR DE ES IT PL NL PT SV The use of the WEEE Symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help protect the environment. For more detailed information about the recycling of this product, please contact your local authority, your household waste disposal service provider or the shop where you purchase the product. Lutilisation du symbole DEEE indique que ce produit ne peut tre trat comme dchet mnager. En garantissant la mise au rebut approprie de ce produit, vous contribuez prserver lenvironnement. Pour plus dinformations sur le recyclage de ce produit, contactez les autorits locales, le fournisseur de service dlimination des dchets mnagers ou le magasin o vous avez achet le produit. Die Verwendung des WEEE-Symbols gibt an, dass dieses Produkt nicht als Haushaltsmll betrachtet werden kann. Durch die korrekte Entsorgung dieses Produktes tragen Sie zum Schutz der Umwelt bei. Ausfhrliche Informationen zum Recycling des Produkts erhalten Sie ber die rtlichen Behrden, die fr Sie zustndige Mllabfuhr oder das Geschft, in dem Sie das Produkt erworben haben. El uso del smbolo RAEE (WEEE) indica que el producto no se puede tratar como un desecho domstico. Si se deshace de este producto debidamente, contribuir a proteger el medioambiente. Si desea obtener informacin detallada acerca del reciclaje de este producto, pngase en contacto con las autoridades locales, el servicio de recogida de basura o la tienda donde ha adquirido el producto. Luso del simbolo RAEE indica che questo prodotto non deve trattato come un rifiuto domestico. Assicurandosi che questo prodotto sia smaltito correttamente, si contribuisce a proteggere lambiente. Per informazioni pi dettagliate sul riciclaggio di questo prodotto, rivolgersi agli enti locali, al fornitore del servizio di smaltimento dei rifiuti domestici o al negozio in cui stato acquistato il prodotto. Symbol WEEE wskazuje, e ten produkt nie moe by traktowany jako odpad gospodarczy. Zapewniajc prawidow utylizacj produktu pomagasz w ochronie rodowiska. Aby uzyska szczegowe informacje na temat utylizacji produktu, naley skontaktowa si z lokalnymi wadzami, przedsibiorstwem wiadczcym usugi usuwania odpadw z gospodarstwa domowego lub sklepem, w ktrym zakupiono produkt. Gebruik van het WEEE-symbool betekent dat het product niet als normaal huishoudelijk afval mag worden verwerkt. U helpt met de bescherming van het milieu door dit product op correctly wijze te verwijderen. Voor meer informatie over het recyclen van dit product, neemt u contact op met het gemeentehuis, uw afvaldienstverlener of de winkel waar u het product hebt gekocht. O uso do smbolo REEE indica que este produto no pode ser tratado como resduo domstico. Ao garantir que este produto eliminado correctamente, estar a proteger o ambiente. Para obter informaes mais detalhadas sobre a reciclagem deste produto, contacte as autoridades locais, o fornecedor de servios de eliminao de lixo domstico ou a loja onde adquiriu este produto. Anvndningen av WEEE-symbolen anger att produkten inte fr hanteras som hushllsavfall. Genom att skerstlla att produkten hanteras p rtt stt bidrar du till att skydda miljn. Mer detaljerad information om tervinningen av denna produkt fr du hos den lokala tervinningsorganisationen, bolaget som hanterar dina hushllssopor eller den terfrsljare dr du kpte produkten. NO DK FI HU EL LT SK CZ RU indikerer at dette produktet Bruken av WEEE-symbolet ikke kan behandles som husholdningsavfall. Du vil bidra til beskytte miljet ved srge for at dette produket blir avhendet p en forsvarlig mte. Ta kontakt med kommunale myndigheter, renovasjonsselskapet der du bor eller forretningen hvor du kjpte produktet for f mer informasjon om resirkulering av dette produktet. Brugen af WEEE symbolet angiver, at dette produkt ikke m behandles som husholdningsaffald. Ved at sikre at produktet bortskaffes korrekt, vil du hjlpe med til at beskytte miljet. For mere detaljerede oplysninger om genbrug af dette produkt, bedes du kontakte din kommune, dit renovationsselskabs tjenesteudbyder eller den butik, hvor du kbte produktet. WEEE-symbolin kytt ilmaisee, ett tt tuotetta ei saa hvitt kotitalousjtteen seassa. Huolehtimalla siit, ett tm tuote hvitetn asianmukaisesti, autat suojelemaan ymprist. Pyyd tarkempia kierrtysohjeita paikallisilta viranomaisilta, jteyhtilt tai liikkeest, josta ostit tuotteen. A WEEE szimblum azt jelzi, hogy a termket nem szabad ltalnos hztartsi hulladkknt kezelni. A termk megfelel rtalmatlantsval hozzjrul a krnyezet vdelmhez. A termk jrahasznostsval kapcsolatos rszletes tudnivalkrt forduljon a megfelel helyi hatsghoz, hulladkgyjt vllalathoz vagy a termket rust zlethez. WEEE
.
,
.
,
,
. EEA simbolis rodo, kad produkto negalima imesti kartu su buitinmis atliekomis. Tinkamai imesdami produkt padsite saugoti aplink. Dl isamesns informacijos, kaip perdirbti produkt, kreipkits vietines atsakingsias institucijas, buitini atliek perdirbimo paslaug teikj arba parduotuv, kurioje sigijote produkt. Pouitie symbolu WEEE oznauje, e tento vrobok sa nesmie likvidova s komunlnym odpadom. Ak vrobok sprvne zlikvidujete, prispejete k ochrane ivotnho prostredia. Podrobnejie informcie o recyklcii vrobku zskate na miestnom zastupitestve, u poskytovateov sluieb likvidcie domovho odpadu alebo v predajni, v ktorej ste vrobok zakpili. Pouit symbolu WEEE oznauje, e tento vrobek nesm bt povaovn za domovn odpad. Zajitnm sprvn likvidace tohoto vrobku pomhte chrnit ivotn prosted. Podrobnj informace o recyklaci tohoto vrobku zskte od mstnch ad, od firmy, kter u vs zajiuje odvoz odpadk, nebo v obchod, kde jste vrobek zakoupili. WEEE ,
.
,
.
, ,
, ,
. EN FR DE ES IT RU CZ PL SK JP KO CS Hereby, Creative Labs Pte. Ltd. declares the Bluetooth headset, model no. EF0810 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at http://www.creative.com/EUDoC Please visit creative.com/support/SXFI Air for user guide, safety and regulatory information and battery removal instruction, which is meant strictly for independently qualified professional. Par la prsente, Creative Labs Pte. Ltd. dclare ce Casque micro Bluetooth que le modle n EF0810 est conforme la Directive 2014/53/EU. Lintgralit du texte de la dclaration de conformit europenne est disponible sur http://www.creative.com/
EUDoC Hiermit erklrt Creative Labs Pte. Ltd. dass Bluetooth-Headset, Modellnr. EF0810 der Richtlinie 2014/53/EU entspricht. Der vollstndige Text der EU-Konformittserklrung ist unter http://www.creative.com/EUDoC verfgbar. Por el presente, Creative Labs Pte. Ltd. declara que el Auriculares Bluetooth con micrfono, modelo n EF0810 cumple con lo establecido en la Directiva 2014/53/UE. El texto completo de la declaracin de conformidad de la UE est disponible en http://www. creative.com/EUDoC Creative Labs Pte. Ltd. dichiara che Cuffie Bluetooth, modello n. EF0810 conforme alla Direttiva 2014/53/UE. Il testo completo della dichiarazione di conformit UE disponibile su http://www.creative.com/EUDoC Creative Labs Pte. Ltd. , EF0810 2014/53/. http://www.creative. com/EUDoC Spolenost Creative Labs Pte. Ltd. tmto prohlauje, Nhlavn souprava Bluetooth, model . EF0810 vyhovuje smrnici 2014/53/EU. pln znn EU prohlen o shod je k dispozici na http://www.creative.com/EUDoC Spka Creative Labs Pte. Ltd. niniejszym owiadcza, e Zestaw suchawkowy Blue-
tooth, model EF0810 jest zgodny z dyrektyw 2014/53/UE. Z penym tekstem deklaracji zgodnoci UE mona zapozna si pod adresem http://www.creative.com/EUDoC Hereby, Creative Labs Pte. Ltd. declares the Bluetooth headset, model no. EF0810 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at http://www.creative.com/EUDoC Hereby, Creative Labs Pte. Ltd. declares the Bluetooth headset, model no. EF0810 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at http://www.creative.com/EUDoC Hereby, Creative Labs Pte. Ltd. declares the Bluetooth headset, model no. EF0810 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at http://www.creative.com/EUDoC Hereby, Creative Labs Pte. Ltd. declares the Bluetooth headset, model no. EF0810 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at http://www.creative.com/EUDoC
, ,
, ,
, , . . ,
. 0C (32F) 45C (113F).
,
.
:
, : EF0810, Creative
: 5V 1.0A
: Creative Labs Pte. Ltd.
:
:
, 142281,
, , , .2, .216.,
: +7 (495) 369-00-84
+7 (901) 706-76-81
: proxy.russia@gmail.com
(, )
,
,
( ): . 020/2011
. 09.12.2011. 879 Additional Safety and Regulatory information for Creative SXFI AIR Regulatory Information The following sections contain notices for various countries:
CAUTION: This product is intended for use with FCC/CE certified computer equipment. Please check the equipment operating/installation manual and/or with the equipment manufacturer to verify/confirm if your equipment is suitable prior to the installation or use of the product. Notice for the USA Federal Communication Commission (FCC) Interference Statement FCC Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be installed with computer equipment certified to comply with Class B limits. All cables used to connect to the computer and peripherals must be shielded and grounded. Operation with non-certified computers or non-shielded cables may result in interference to radio or television reception. may result in interference to radio or television reception. MODIFICATION: Any changes or modification not expressly approved by the grantee of this device could void the users authority to operate the device the users authority to operate the device. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Notice for Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Canada Radiation Exposure Statement This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites dexposition aux radiations IC CNR-102 tablies pour un environnement non contrl. Cet metteur ne doit pas tre situ ou fonctionner conjointement avec une autre antenne ou un autre metteur. MODIFICATION: Any changes or modification not expressly approved by the grantee of this device could void the users authority to operate the device. Toute modification non approuve explicitement par le fournisseur de licence de lappareil peut entraner lannulation du droit de lutilisateur utiliser lappareil. Ukraine RoHS Statement
, 3 2008 1057 Li - ion
(http://jp.creative.com/support/contact/
!
/JBRC http://www. jbrc.com/
Vietnam RoHS Statement This product is in compliance with Circular 30/2011/TTBCT of the Ministry of Trade of the Socialist Republic of Vietnam (Circular), it does not contain the following substances in concentration greater than the Maximum Limit value as specified in the Circular. Substance Maximum Limit (ppm) 1, 2
* lead
* mercury
* cadmium
* hexavalent chromium
* polybrominated biphenyls (PBB)
* polybrominated diphenyl ethers (PBDE) 1000 1000 100 1000 1000 1000 1 Maximum Limit does not apply to applications exempted from the Circular. 2 Maximum Limit refers to concentration by weight in homogeneous materials. SUPPLIERS DECLARATION OF CONFORMITY According to CFR Title 47 2.1077 Importers Name:
Importers Address:
Creative Labs, Inc. 1901 McCarthy Boulevard Milpitas, CA. 95035 Tel: (408)428-6600 declares under its sole responsibility that the product Trade Name:
Model Numbers:
Product Name:
Creative EF0810 Creative SXFI AIR has been tested according to the FCC / CISPR22 requirement for Class B devices and found compliant with the following standards:
EMI/EMC: ANSI C63.4 & C63.10, FCC Part 15 Subpart B & C Complies with Canadian ICES-003 Class B & RSS-247 standards This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including Interference that may cause undesirable operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Supplementary Information:
Thinh Bui Compliance Manager Creative Labs, Inc. 14th Dec 2018 JP www.creative.com
:
(Bluetooth) Bluetooth 20cm KO
. www.creative.com .
: .
(Bluetooth ) Bluetooth . , , , ,
. 20cm . BI Instruksi Keselamatan Baterai Tersemat Jangan coba-coba melepas baterai yang tersemat. Produk ini harus dibuang sesuai dengan peraturan lingkungan setempat. Untuk mengganti baterai, kembalikan produk Anda ke kantor dukungan di wilayah Anda. Untuk informasi layanan produk, kunjungi www.creative.com. Jangan sampai produk terkena panas yang berlebih seperti sinar matahari atau sejenisnya. PERHATIAN: Berisiko meledak jika baterai diganti dengan tipe yang salah. Gantikan hanya dengan jenis yang sama atau yang setaraf.
(Panduan tambahan untuk perangkat Bluetooth) Sinyal frekuensi radio gelombang pendek dari perangkat Bluetooth dapat mengganggu fungsi perangkat elektronik dan medis lain. Matikan perangkat jika dilarang menggunakannya. Jangan gunakan perangkat di fasilitas medis, pesawat, pom bensin, dekat dengan pintu otomatis, alarm kebakaran otomatis, atau perangkat lainnya yang dikendalikan secara otomatis. Jauhkan perangkat ini setidaknya 20 cm dari alat pacu jantung dan perangkat medis lain. Gelombang radio dapat mengganggu fungsi alat pacu jantung dan perangkat medis lainnya. AR
1 2 | Internal Photos | Internal Photos | 1.61 MiB | December 20 2018 / June 18 2019 |
SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 7 Internal Photos for SZEM1808008017CR FCC ID: 2AJIV-EF0810 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 7 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 7 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 7 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 7 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 7 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 7 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
1 2 | External Photos | External Photos | 597.76 KiB | December 20 2018 / June 18 2019 |
SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 5 External Photos for SZEM1808008017CR FCC ID: 2AJIV-EF0810 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 5 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 5 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 5 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 5 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Companys findings at the time of its intervention only and within the limits of Clients instructions, if any. The Companys sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.
1 2 | Label | ID Label/Location Info | 52.74 KiB |
Justification of Label Location Regarding: Label Location of EF0810, FCC lD: 2AJIV-EF0810 We, CneRtlVE LABS PTE. LTD.., hereby verify that the label of the equipment will not be visible at the time of purchase on the exterior of the equipment enclosure, Per KDB 784748 D01 Labelling Part 15 &18 Guidelines v08, we adopt an alternative option to placing the FCC label on the device, all requirements as below are met:
1 2 3 Requirements The device is handheld;
The FCC identifier is visible at the time of purchase, The FCC lD on the box, or additional documentation directing the user where to find the FCC label, also satisfies this requirement;
The user accessible area must not require any special tools for access, and the FCC label must not be placed on a removable part;
Justification It's a headphone, could be handheld when not in use, lnstruction to user where to find the FCC labelis properly addressed in the User Manual, It's on the internal side of the earcup which is covered by the cushion, and the cushion could be easily removed without any special tools or efforts meanwhile could be put on easily. Though KD9784748 V08 has been replaced by V09r01, FCC OET has confirmed the continuing invalidation of this alternative label location proposed in previous version of this KDB via inquiry. Print Name: Toh Mary signature: \\t.^^^, - >t\q\aor8 Title: Product Safety Manager N On behalf of Company: CREATIVE LABS PTE. LTD. Telephone: +65689541 96 E-mail: marytoh@ctl.creative.com
1 2 | Authorization Letter | Cover Letter(s) | 46.95 KiB | December 20 2018 |
Date: 2018-11-01 Creative Labs Pte Ltd TO Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: 2AJIV-EF)BI 0 To whom it may concern:
We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Jing Song in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC lD above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, lnc., still resides with Creative Labs Pte Ltd. This authorization is valid until further written notice from the applicant. Title: Product Safety Manager Print Name: Toh Mary Signature On behalf of Company: CREATIVE LABS PTE LTD. Telephone: +65-689541 96 E-mail : marytoh@ctl.creative.com Print Name: LIAN YAM Title: Associate Director, Product Development Signature:
On behalf of Company: CREATIVE LABS PTE LTD Telephone: +65-68954474 E-mail : yflian@ctl.creative.com
1 2 | Confidentiality Letter | Cover Letter(s) | 43.23 KiB | December 20 2018 |
To:
Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: Creative Labs Pte Ltd. 31 lnternational Business Park #03-01 Creative Resource 609921 Singapore Regarding: Confidentiality Request regarding application for FCC lD: 2AJIV-EF0810 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission's rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential untilthe device is marketed or 180 days from the grant date, whichever is less. lf the device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos lnternal Photos Test Setup Photos User manual(s) Print Name: Toh Mary Signature On behalf of Compa ny: CREATIVE LABS PTE LTD Telephone: +65-689541 96 E-mail : marytoh@ctl.creative. com Title: Product Safety Manager Print Name: LIAN YAM FEI Title: Associate Director, Product Development Signature:
On behalf of Company: C LABS PTE LTD Telephone: +65-68954474 E-mail: yflian@ctl.creative.com
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2018-12-20 | 2402 ~ 2480 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
2 | 2402 ~ 2480 | DTS - Digital Transmission System |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2018-12-20
|
||||
1 2 | Applicant's complete, legal business name |
Creative Labs Pte. Ltd.
|
||||
1 2 | FCC Registration Number (FRN) |
0025820259
|
||||
1 2 | Physical Address |
31 International Business Park #03-01
|
||||
1 2 |
Singapore, N/A 609921
|
|||||
1 2 |
Singapore
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
U******@SGS.COM
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
2AJIV
|
||||
1 2 | Equipment Product Code |
EF0810
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
T**** M****
|
||||
1 2 | Telephone Number |
68954********
|
||||
1 2 | Fax Number |
N/A********
|
||||
1 2 |
m******@ctl.creative.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
SGS-CSTC Standards Technical Services Co., Ltd
|
||||
1 2 | Name |
K**** X******
|
||||
1 2 | Physical Address |
No.1 Workshop, M-10, Middle Section
|
||||
1 2 |
Shenzhen, 518057
|
|||||
1 2 |
China
|
|||||
1 2 | Telephone Number |
0755-********
|
||||
1 2 | Fax Number |
0755-********
|
||||
1 2 |
k******@sgs.com
|
|||||
app s | Non Technical Contact | |||||
1 2 | Firm Name |
SGS-CSTC Standards Technical Services Co., Ltd
|
||||
1 2 | Name |
J******** S****
|
||||
1 2 | Physical Address |
No.1 Workshop, M-10, Middle Section
|
||||
1 2 |
Shenzhen, 518057
|
|||||
1 2 |
China
|
|||||
1 2 | Telephone Number |
0755-********
|
||||
1 2 | Fax Number |
0755-********
|
||||
1 2 |
J******@sgs.com
|
|||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 06/18/2019 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 2 | DTS - Digital Transmission System | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | SXFI AIR | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | Yes | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Output Power listed is conducted. | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
SGS-CSTC Standards Technical Services Co., Ltd
|
||||
1 2 | Name |
K****** X****
|
||||
1 2 | Telephone Number |
+86 (********
|
||||
1 2 |
K******@sgs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2402.00000000 | 2480.00000000 | 0.0024000 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | 2402.00000000 | 2480.00000000 | 0.0022000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC