FCC ID: KA2PR1040A1 1USB2.0 port MFP Print Server

i D-Link DPR-1040

Manual Rev. 01 (September, 2008) ii Contents Package Contents ............................................................................................ iv Contents of Package: ......................................................................................... iv System Requirements: ........................................................................................ v Introduction ....................................................................................................... 1 External Features .............................................................................................. 4 Port Connectors .................................................................................................. 4 Rear Panel Connectors ....................................................................................... 5 Network Cable Connector ................................................................................... 5 DC Power Connector .......................................................................................... 5 LED Indicators ..................................................................................................... 6 Setting up the DPR-1040 ................................................................................... 7 Installing the Print Server .................................................................................... 7 Power ON Self-Test ............................................................................................. 8 Getting Started ................................................................................................. 10 Using PS Software ........................................................................................... 11 Auto-Run Installation ......................................................................................... 11 1 PS Software ...................................................................................................... 12 Installing PS Software ....................................................................................... 12 Using PS-Link .................................................................................................... 16 Installing and Using MFP/GDI Printer ............................................................... 27 Using PS-Wizard ............................................................................................... 48 Using the Web Configuration ......................................................................... 54 Home ................................................................................................................. 54 SETUP LAN Setup ......................................................................................... 58 SETUP Printer Setup ..................................................................................... 59 ADVANCED > Advanced LAN ........................................................................... 68 ADVANCED > User Access .............................................................................. 70 ADVANCED > E-Mail Notification ..................................................................... 72 ADVANCED > SNMP ........................................................................................ 74 MAINTENANCE > Password ............................................................................ 75 MAINTENANCE > Save/Restore Settings ........................................................ 76 MAINTENANCE > Firmware Upgrade .............................................................. 77 MAINTENANCE > Diagnostics ......................................................................... 78 STATUS > Device Info ....................................................................................... 79 STATUS > Network ........................................................................................... 80 STATUS >Print Log ........................................................................................... 82 HELP ................................................................................................................. 83 Reboot ............................................................................................................... 84 Refresh Printer Status ....................................................................................... 85 TCP/IP Printing for Windows Vista ................................................................ 86 TCP/IP Printing for Windows XP .................................................................... 96 TCP/IP Printing for Windows 2000 ............................................................... 111 TCP/IP Printingfor Windows 98SE/ME ..... .................................................. 126 2 Unix/Linux Printing ....................................................................................... 142 Printing Text Files form Unix............................................................................ 142 Printing form BSD Unix Versions .................................................................... 143 iii Printing from SCO Unix System V/386 ........................................................... 146 Printing from Solaris ........................................................................................ 148 Printing from Red Hat Linux ............................................................................ 149 Setting up Printing in Mac OS X Tiger(10.4.9) ............................................ 156 Adding a Printer ............................................................................................... 157 AppleTalk-enabled or Bonjour-enabled Printers ............................................. 160 Setting up AppleTalk Printing in Mac OS 9 ................................................ 174 Technical Specifications .............................................................................. 179 Contacting Technical Support ..................................................................... 180 Warranty and Registration ........................................................................... 181 Package Contents 3 Contents of Package:

D-Link DPR-1040 USB 2.0 MFP Server

Manual and Warranty on CD

Printed Quick Installation Guide If any of the above items are missing, please contact your reseller. v System Requirements:

A computer with an installed Ethernet adapter

Windows Vista/XP/2000/NT4/ME/98SE/95

Apple Mac OS 9.x to MAC OS X 10.4.x

Linux, Solaris, SCO Unix, AIX 4

Internet Explorer 6.0 or above; Netscape Navigator version 6.0 or above, with JavaScript enabled

Printer must support required operating system Introduction The D-Link DPR-1040 Print Server is an Ethernet/USB print server that connects to your Ethernet, Fast Ethernet or USB network anywhere you wish to locate printer services. The DPR-1040 manages the flow of print files from workstations or file servers to connected printers, delivering print jobs to printers much faster than a file server or a PC acting as a print server can. With one IEEE1284 parallel port and two USB 2.0 ports, DPR-1040 can connect to almost any make and model printer on the market today. The DPR-1040 includes easy-to-use software to install on most Windows-based networks. Protocol support for TCP/IP, NetBEUI, and AppleTalk are provided to ensure seamless connection to major networking Operating Systems. The DPR-1040 has a built in Web-Based management feature that allows users to easily configure and manage multiple print queues through TCP/IP. The DPR-1040 improves network printing services in the following ways:

The DPR-1040 picks up the workload of managing print file traffic to its connected printers. This provides workload relief to your file servers, and allows the file servers full capacity to be used for file access or other direct services to network users. On peer-to-peer networks, workstations can print directly to the Print Server without increasing the load of another workstation or server.

Because the DPR-1040s very portable and inexpensive compared to a PC-based print server, and Print Server connects to your file servers through the network, 5 printers can be deployed to locations of maximum convenience to users.

Use USB redirection software (PS-Link) to support MFP printers print/scan/fax/copy functions and GDI printers printing.

Use the easy-to-add printer software (PS-Wizard) to add a network printer on Windows for traditional printers TCP/IP printing. The DPR-1040 offers extraordinary flexibility, operating with all major network operating systems and protocols:

TCP/IP UNIX lpr/lpd (HP-UX, SunOS, Solaris, SCO, UnixWare, IBM AIX) Windows NT/2000, Windows 95/98SE/ME, Windows XP/Vista, NetWare 5.x NDPS LPR Remote Printing

NetBEUI Windows NT/2000/XP, Windows 95/98SE/ME, Windows for Workgroups, Microsoft LAN Manager, IBM LAN Server

AppleTalk MacOS EtherTalk Furthermore, the MFP server features various useful software utilities: PS Softwarea user-friendly program used to complete further settings for the MFP Server, contains PS-Link and PS-Wizard:

PS-Link

Fax) of a MFP printer, printing of GDI printer, and even other multimedia software A useful tool for you supporting multi-functions (Print/ Scan/ Copy/

of any MFP/GDI printer. For the detail information, see the Using The PS Software chapter in this manual.

PS-Wizard

See also the Using The PS Software chapter in this manual for the details. A simple tool for you easily adding a printer on your computer. 6 External Features Port Connectors The DPR-1040s USB printer port is located on its rear panel, and is configurable using the Web Configuration Interface. The Print Servers Web configuration permits users to configure settings through the web browser. Default IP Address of DPR-1040 is set as automatically getting from DHCP server or Router which build-in DHCP server. NOTE: The PCs IP Address must be in the same subnet as the Print Servers IP Address for the two devices to communicate. (For example, if MFP servers IP Address is 192.168.0.10, with a subnet mask of 255.255.255.0, then your computers IP Address should be 192.168.0.x, where x is a value between 1-254, excluding 10.) 7 Rear Panel Connectors Network Cable Connector The Print Servers rear panel feature an RJ-45 connector for connection to 10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which should be Category 5 twisted-pair cable). The port supports the NWay protocol, allowing the Print Server to automatically detect or negotiate the transmission speed of the network. DC Power Connector The DC power input connector is located on the Print Servers rear panel and is labeled DC 5V. 8 LED Indicators The upper part of the Print Server features three LED indicators:

Power Steady green confirms that the Print Server is powered ON.

USB When these LEDs light in steady green, it indicates the printer is on line now. While if these LEDs light in blinking green, it indicates that data is transferred between print server and printer. These three indicators are also used by the Print Servers Power-ON Self Test

(POST) to indicate any hardware failures.

Link/Act Steady green confirms that the Print Server has a good connection to the Ethernet or Fast Ethernet network. The indicator blinks off briefly to indicate that the Print Server is receiving or transmitting from the network.

WirelessLink/Act Steady green confirms that the Print Server has a good connection to the Wireless network. The indicator blinks off briefly to indicate that the Print Server is receiving or transmitting from the network. 9 Setting up the DPR-1040 Installing the Print Server WARNING: Configuration problems may result if the Print Server is powered up without first establishing its network connection. Follow this procedure to avoid complications at the configuration stage. 1. Confirm proper operation of each of the printers to be connected to the DPR-1040. 2. When you have confirmed proper operation of each printer, switch its power OFF. 3. Confirm that your network is operating normally. 4. Connect the DPR-1040 RJ-45 Connector to the network, using an Ethernet CAT5 cable. 5. While each printer is powered OFF, install the corresponding parallel or USB printer cable to connect the printers parallel port or USB port to the printer port of the Print Server. 6. Switch on each connected printer. 7. Plug the AC power adapters DC output plug into the DC 5V power socket on the rear panel of the Print Server. 8. Plug the power adapter into a power outlet. This will supply power to the Print Server, as it has no external power switch. The green Power LED on the Print Servers front panel should illuminate steadily, and the Print Servers Self-Test will proceed. 10 Power ON Self-Test Every DPR-1040 has been factory-tested to operate properly. When the DPR-1040 is powered ON, it also automatically performs a Self-Test on each of its major components. The final result of the Self-Test is signaled by the state of the USB LED indicator following the Self-Test. Preliminary to the actual component tests, the three LED indicators are tested to confirm their steady and flashing operation. Immediately after power-up, all three of the green LEDs should illuminate steadily for several seconds. Then the USB LED should light OFF simultaneously. Irregularity of any of the three LEDs during these LED tests may mean there is a problem with the LEDs themselves. The actual component tests immediately follow the LED tests. A normal (no fault) result is signaled by a simultaneous flashing of these three LEDs three times, followed by a quiescent state with all three LEDs dark. If the Self-Test routine traps any component error, then following the LED tests the Self-Test will halt and the LEDs will continuously signal the error according to the following table. In the event of any such error signal, contact your dealer for correction of the faulty unit. 11 12 Getting Started Below is a sample network using the DPR-1040. The DPR-1040 has a built- in Web-based management feature that allows users to easily configure and manage multiple print queues through TCP/IP. WARNING: Only a USB printer may be connected to the USB port of the DPR-1040. Do not connect any other USB devices to the USB port of the DPR-1040; to do so, may damage the unit and will void the warranty for this product. For a list of printers that are compatible with the DPR-1040, please see the Appendix in this manual. The compatibility list is not comprehensive. Even if it is not included in the list, your printer may be compatible with the DPR-1040. 13 Using PS Software This chapter will introduce you the installation and operation of various useful software program PS Software (contains PS-Link and PS-Wizard) with which the MFP Server is featured. Auto-Run Installation Insert the Installation CD-ROM into your computers CD-ROM drive to initiate the Auto-Run program. The content of the Installation CD-ROM includes:

Install PS Software click to install PS Software, which contains PS-Link and PS-Wizard, to complete further settings for the MFP Server, such as:

- Changing IP address

- Supporting multi-function (Print/ Scan/ Copy/ Fax) of a MFP printer, printing of GDI printer, and even other multimedia software of any MFP/GDI printer.

- Adding a printer on your computer in the easiest way.

 View Quick Installation Guide - click to preview the Quick Installation Guide in PDF format for step-by-step instructions of the MFP Server Installation.

 View Manual click to preview the User's Guide in PDF format for detailed information of the MFP Server. Install Acrobat Reader click to launch Acrobat Reader for the viewing and printing of PDF files in the Installation CD-ROM.

 Exit click to close the Auto-Run program. 14

PS Software To avoid the conflict in your network, you can use PS Software to change the related settings of your MFP Server (such as the IP address) after finishing the installation of PS Software on your PC. The PS Software contains two utilities: PS-Link and PS-Wizard. Installing PS Software 1. Click the PSSoftwareSetup icon of the Installation CD-ROM, and then the system will prompt a window for you to select a desired setup language from its pull-down menu. After done the selection of language, click the OK button to continue. 15 2. Click the Next> button in the welcome window of InstallShield Wizard. 3. Specify the destination location by clicking the Browse button. Otherwise, leave the default setting and click the Next> button to continue. 16 4. You may enter a new folder name in the Program Folder field if you want to change the default name. Otherwise, you may leave the default setting and click the Next> button to go on the installation. 5. The InstallShield Wizard starts to install the software, and the Progress bar indicates the installation is proceeding until the following window shows up. Click the Finish button to complete the installation. 17 After installing the program, the application program for the MFP Server is automatically installed to your computer, and creates a folder in Start Programs PS Software. The PS Software contains two utilities: PS-Link and PS-Wizard. 18 Using PS-Link PS-Link, supports for Windows 2000/XP/2003/Vista, is a useful tool for you setting up multi-function (Print/ Scan/ Copy/ Fax) of a MFP printer, printing of GDI printer, and even other multimedia software of any MFP/GDI printer. That is, the main goal and advantage of the PS-Link is to enable the MFP Server to support MFP/GDI printers. Go to Start=> Programs=> PS Software, and select PS-Link. The PS-Link will automatically search the MFP servers in the same network segment. If the installation is successful, you will see the name of your MFP server is discovered and listed in the Server Name column of the following window. If your MFP server identity data is not shown up, please check its network connectivity and click the Discover button to research it again. 19 Server Name: A list displays the name of the connected MFP Server within the network. Discover: You may click this button to manually research the current connected MFP Server. Status Bar: Display the current status about the system and the numbers of the connecting MFP Servers. Information: This field displays the basic information of the selected MFP Server in the Device List, including MAC and IP addresses, device model name, system status, firmware version and UpTime information. Also, three buttons are provided in this field: Setup Wizard, Change IP Address, and Web Setup for you to do further configuration. 20

[Setup Wizard] Setup Wizard is a step-by-step setup interface, which correspond with the Configuration of the Web-based Configuration Utility, allowing user to do basic setup easily. When this button is clicked, a welcome window will show up as the following. The Setup Wizard allows you to do a series of configuration of the MFP Server, including:

21 System Settings 22 Change IP Address:

23 Workgroup of Microsoft Network 24 AppleTalk Settings 25 After done the configuration, click Save to restore the current setting or Cancel to abort. 26

[Change IP Address] - Click this button to bring up the following pop-up window, which allows you to change the IP Address of the MFP Server in two methods:

Manually Assign or DHCP Assign Automatically. When done the setting, click OK button or Cancel button to abort. 27

[Web Setup] When this button is clicked, your Web browser and the MFP Servers Web Configuration Utility will be auto-launched. Alternately, you may double click the MFP Server in the Server Name to launch the Web Configuration Utility. Printer Port: This field not only displays the basic information and current status of the connected printer, but also allows you to do further configuration in the use of the four control buttons (Link, UnLink, Lock, UnLock).

[Link] The function of this button is to simulate the physical connection between a USB cable of the printer and your computer, That is, you can easily set up a link between a printer and your computer only by clicking this button without physically attaching the printers USB cable to your computer. 28

[UnLink] Contrary to the Link button, the UnLink button is used to off link between the printer and your computer without physically disconnecting the two devices.

[Lock] Since the operation mode of the MFP can be set as Single User Mode (i.e. only single specific computer can do printing) or Shared Mode (the default setting). Clicking the Lock button, you may enable the Single User Mode.

[UnLock] Clicking this button to enable the MFP as Shared Mode (i.e. End up the Single User Mode of the MFP). About: You may click this button to bring up a pop-up window as below to verify the basic information about the PS-Link. Click OK button to close this window. Close: To exit PS-Link, click this button. 29 Installing and Using MFP/GDI Printer This section will introduce you how to start the initial installation of various MFP/GDI printer in the use of the printer manufacturers CD-ROM. Likewise, how to use MFP/GDI printer through the PS-Link utility of the MFP Server after the printer manufacturers driver is installed on your computer. For PC with the MFP/GDI printer driver installed:

If your computer was already installed with the MFP/ GDI printer driver, you can just click [Link] button of PS-Link to complete the connection between the printer and your computer. For PC without the MFP/GDI printer driver installed:

If your computer never had initial installation of the MFP/GDI printer driver, you may follow the following procedure to achieve it. 1. Insert the manufacturers CD-ROM into your computers CD-ROM driver to initiate Auto-Run program. 2. Following the instructions of the manufacturers CD-ROM to install MFP driver and other media software until you are requested to attach the printers USB cable to your computer. 3. When you are requested to do physical connection between the printer and your computer, the following installation steps will be different depending on the manufacturer brand. Here lists illustrations for several printers of major manufacturers:

30 For HP:

1. When the installation program asks you to connect the USB cable, you are allowed to connect the printer with you computer later by checking the box. Then click Next> button to continue the rest of the installation (generally, for other multimedia software such as scanner driver, etc.). 31 2. When the installation of all drivers of the MFP/GDI printer CD-ROM on your computer is done, you may use PS-Link to complete the physical connection between the MFP/GDI printer and your computer by clicking [Link] button. 32 As long as the connection is linked successfully, a prompt of PS-Link as below will show up to inform you. Press OK to exit. 3. Now the MFP/GDI printer is ready to serve you with its multi-functions

(Print/Scan/Copy/Fax). You may start to use the MFP/GDI printer through your computer. 33 For EPSON:

34 1. When the installation program asks you to connect the USB cable of the MFP/GDI printer to your computer, you are not allowed to ignore it; therefore, you need to utilize PS-Link to complete it. 2. Launch the PS-Link utility and click the [Link] button. 35 When the connection is completed successfully, a prompt as below will show up to inform you. Press OK to exit. 3. Then you have to go back to continue the installation of the MFP/GDI printer CD-ROM on your computer in order to complete the rest of installation steps. 4. When the whole installation of the MFP/GDI printer CD-ROM on your computer is completed. You may start to use multi-functions (Print/Scan/Copy/Fax) of the MFP/GDI printer through your computer. 36 For Canon:

1. When the installation program asks you to attach the MFP/GDI printer to your computer, you are not allowed to skip this step; therefore, you need to utilize PS-Link to complete such physical connection. 37 2. Launch the PS-Link utility and click the [Link] button. 38 When the connection is completed successfully, a prompt as below will show up to inform you. Press OK to exit. 3. Then you have to go back to do the installation of MFP/GDI printer CD-ROM on your computer in order to complete the rest of installation steps. 4. When the whole installation of the MFP/GDI printer CD-ROM on your computer is completed. You may start to use multi-functions (Print/Scan/Copy/Fax) of the MFP/GDI printer through your computer. 39 For Lexmark:

1. When the installation program asks you to attach the MFP/GDI printer to your computer, then you have to follow; otherwise, you will not allow continuing the installation. Therefore, you need to utilize PS-Link to complete it without doing physical connection for the MFP/GDI printer and your computer. 40 2. Launch the PS-Link utility and click the [Link] button. 41 When the connection is completed successfully, a prompt as below will show up to inform you. Press OK to exit. 3. Then you have to go back to finish the installation of MFP/GDI printer CD-ROM on your computer for completing the rest of installation steps. 4. When the whole installation of the MFP/GDI printer CD-ROM on your computer is completed. You may start to use multi-functions (Print/Scan/Copy/Fax) of the MFP/GDI printer through your computer. 42 For Samsung:

43 1. When the installation program asks you to connect the printer to your computer, just ignore it and click Next> button to continue. 2. Soon after Next> button is clicked, the program will prompt you again to connect the two devices, click No to ignore it and go on the rest of the installation (generally, for other multimedia software such as scanner driver, etc.). 44 3. After the installation of the MFP/GID CD-ROM is finished, you may start to utilize PS-Link to complete the physical connection between the MFP/GDI printer and your computer. Click the [Link] button of the PS-Link window as below. When the connection is done successfully, a prompt of PS-Link window as below will show up to inform you. Press OK to exit. 4. Now the MFP/GDI printer is ready to serve you with its multi-functions

(Print/Scan/Copy/Fax). You may start to use the MFP/GDI printer through your compute. 45 For Brother:

1. When the installation program asks you to plug in the USB cable of the MFP/GDI printer to your computer, then you have to follow; otherwise, you will not allow continuing the installation. Therefore, you need to utilize PS-Link to complete it without doing physical connection for the MFP/GDI printer and your computer. 46 2. Launch the PS-Link utility and click the [Link] button. 47 When the connection is completed successfully, a prompt as below will show up to inform you. Press OK to exit. 3. Then you have to go back to finish the installation of MFP/GDI printer CD-ROM on your computer for completing the rest of installation steps. 4. When the whole installation of the MFP/GDI printer CD-ROM on your computer is completed. You may start to use multi-functions (Print/Scan/Copy/Fax) of the MFP/GDI printer through your computer. 48 For Fuji Xerox:

1. Owing to the installation program of Xerox MFP/GDI printer will not request you to do physical connection between the printer and your computer during the installation of the MFP/GDI printer driver on your computer, you may just accomplish the whole installation on your computer at one go. 49 2. While after the installation is finished, you have to link the connection between the MFP/GDI printer and your computer in order to use the MFP/GDI printer on your computer. Thus, you need to utilize PS-Link to link the two devices. Launch the PS-Link utility and click the [Link] button. When the connection is completed successfully, a prompt as below will show up to inform you. Press OK to exit. 3. Now the MFP/GDI printer is ready to serve you with its multi-functions

(Print/Scan/Copy/Fax). You may start to use the MFP/GDI printer through your computer. 50 Using PS-Wizard PS-Wizard, supports for Windows 2000/XP/2003/Vista, is a simple and useful tool for you easily adding a printer on your computer in order to quickly start your printing task without any complicated configuration. That is, the main goal and advantage of the PS-Wizard is to let you add a printer on your PC in the easiest way. Furthermore, the PS-Wizard also allows you to set up IP addresses of MFP Server, such as IP address, Subnet Mask address,, and default Gateway address. Go to Start => Programs => PS Software, and select PS-Link. 51 Print Server: This field allows you to manually discover the connected MFP Server and to do further configuration of the MFP Server that is selected from the list. 52 LAN: You may also to specify dynamic or static IP address for your MFP Server.Then click Apply button to implement the new setting. Port Information: This is the main function of the PS-Wizard for you to easily add a printer on your computer. To add a printer, click

, then the following window will display. 53 The wizard provides three ways for you to select printer driver:

1. Show current installed drivers:

You may select this option, Show currently installed drivers, to check if the same printer driver already existed for use. If not, you may try the next method. After done the selection of printer driver, click Next> button to continue. 2. Select from manufacturer list:

Check this option, Select from manufacturer list, to manually select your printer from drop-down menus by brand and model. Click Next> button to continue when you find a desired driver. If not, try the last way (Have Disk). After done the selection of printer driver, click Next> button to continue. 3. Have Disk:

Click Have Disk button to bring up the following window. Insert the manufactures installation CD-ROM to install the printer driver. After the correct driver is selected, click OK button to continue. 54 After done the selection of printer driver, the wizard will ask you to confirm your selection again in the following window. Beside, you are allowed to edit the name of the printer in the field Network Printer Name and enable this printer as the default printer by checking the box Use this printer as the default printer for Windows-based programs. After you done the verification and configuration in the following window, click Next>

button to continue. Then the printer (e.g. HP Laser 2000 used in this manual) will be auto-created in Windows Printers and Faxes window as the following illustration. 55 When the following window shows up, you may do print test by clicking Print Test Page button to check if you can do printing normally. If yes, then click Finish button to exit the installation window and now you may start your printing tasks. 56 Using the Web Configuration Home To begin managing the DPR-1040, simply launch the browser (e.g. Internet Explorer 6.0 used in this manual) you have installed on your computer and direct it to the URL address: dlink-xxxxxx, where xxxxxx are the last six digits of DPR-1040s MAC address. The MAC address can be found on the bottom side of the DPR-1040 device. When you enter the correct URL, a password input dialog will pop up the following screen. Input admin in the User name field, leave the Password field as blank, and then click the OK button. Then the main screen of the MFP Servers configuration will appear (see below). In 57 addition to the product information, you can access and control the MFP Servers configuration through five links on the top of this main screen: Setup, Advanced, Maintenance, Status, and Help. You may click a desired link from the bar, to display its submenu and select a desired option listed in the left column, and then the corresponding content will show up in the center column. 58 SETUP > Print Server Setup The Print Server Setup screen allows you to modify the Print Server Name and Port Name. D-Link does not recommend changing these settings unless asked to do so by your network administrator. Print Server Name In this section, you can configure the basic information of MFP server. The basic information contains a name of the print server, assigned in the Server Name field, and a location for the print server, assigned in Location (optional) field. 59 Port Settings In this section, you can assign the Port Name for the print server, and the description for the Printer port. It also allows you to select the PJL Printer setting (Yes or No).

: PJL (Printer Job Language) has certain job requirements that must be met to work correctly. For more information, please refer to your printer's manual. Once you have changed the settings in each option, click the Apply Settings button to save the settings, or click Cancel to abandon. 60 SETUP LAN Setup The LAN Setup screen allows you configure the local network settings of MFP server. Please note that this section is optional and you should not need to change any of the settings here to get MFP server up and running. TCP/IP This field allows you to assign IP address in manual or automatic method. When clicking Manually Assign, you should enter the related information in the following boxes, including IP Address, Subnet Mask, and Default Gateway. Once you have changed the settings in each option, click Apply Settings to save the settings, or click Cancel to abandon. 61 SETUP Printer Setup The Printer Setup screen allows you install the printer drivers for the printer currently connected to your print server. 62 Network Printer Wizard Clicking Next to download and run a windows wizard program which will install a network printer onto your computer. When you click Next you will be asked to download and run some software. The above screen is the Network Printer Wizard so please click RUN, and if a second window appears as below click RUN again. 63 Please select the printer required, then click NEXT to continue. 64 The wizard provides three ways for you to select printer driver:

1. Show current installed drivers:

You may select this option, Show currently installed drivers, to check if the same printer driver already existed for use. If not, you may try the next method. After done the selection of printer driver, click Next> to continue. 65 2. Select from manufacturer list:

Check this option, Select from manufacturer list, to manually select your printer from drop-down menus by brand and model. Click Next> to continue when you find a desired driver. If not, try the last way (Have Disk). After done the selection of printer driver, click Next> to continue. 66 3. Have Disk:

Click Have Disk button to bring up the following window. Insert the manufactures installation CD-ROM to install the printer driver. After the correct driver is selected, click OK to continue. After done the selection of printer driver, the wizard will ask you to confirm your selection again in the following window. Beside, you are allowed to edit the name of the printer in the field Network Printer Name and enable this printer as the default printer by checking the box Use this printer as the default printer for Windows-based programs. After you done the verification and configuration in the following window, click Next>

to continue. Then the printer (e.g. HP Laser 2000 used in this manual) will be auto-created in Windows Printers and Faxes window as the following illustration. 67 68 When the following window shows up, you may do print test by clicking the Print Test Page button to check if you can do printing normally. If yes, click the OK button to close the D-Link Add Printer Wizard dialogue screen. 69 If yes, then click the Finish button to exit the installation window and now you may start your printing tasks. 70 ADVANCED > Advanced LAN The Advanced LAN screen allows you to further network setting of MFP server, while you are recommended better not to change the settings unless instructed to modify the setting by your network administrator. The Advanced LAN screen contains these sections: TCP/IP, Microsoft Network, and AppleTalk. 71 TCP/IP This section contains four options that allow you to configure the TCP/IP setting:

DNS Server Address, UPnP, Mac Bonjour/Rendezvous, and Second HTTP Port.

UPnP: This option allows you to enable or disable UPnP function.

Mac Bonjour/Rendezvous: This option allows you to enable or disable Mac Bonjour/Rendezvous function.

Second HTTP Port: This option allows you to enable or disable Second HTTP Port for remote Web Configuration and IPP Printing. Microsoft Network Enter the name of the Workgroup that you want the print server associated with in this field. AppleTalk Enter the AppleTalk Zone name in the box. In the following options, enter the related configuration, such as the printer type. Chooser Name: Display the print server's port name. Printer Type: Enter the printer's type in this box. PostScript Level: Select from the pull-down menu (Level 1 or Level 2). Font Group: Select from the pull-down menu. Once you have changed the settings in each option, click Apply Settings to store the settings, or Cancel to abandon. 72 ADVANCED > User Access The User Access screen allows you to create and maintain an authorized list of users that are allowed to access the MFP server. User Access By configuring the Enable Authorised User List option (Yes), the user in the User List is permitted to access the print server. Any user who is not added in the User List will not be allowed to access the print server. Once you have changed the settings in each option, click the Apply Settings button to store the settings, or click the Cancel button to abandon. 73 Authorised Users You can add or delete any user to or from the User List. The User List at the bottom of the screen displays the current defined user and related information for the print server. 74 ADVANCED > E-Mail Notification The E-Mail Notification screen allows you to assign an E-mail address to the MFP Server, so that your mail of the account can be printed out directly through the printer (ASCII text only). This screen also allow you choose where to send an email when the printer status changes. 75 Enable E-mail Notification You can set the print server to send an alert message when the printer status changes through E-mail. To enable this function, click Yes under Enable e-mail notification. Then, input the administrator's E-mail address in the Destination e-mail Address field. E-mail Account Details You can assign an E-mail address to the print server, so that your mail of the account can be printed out directly through the printer (ASCII text only). To enable this function, enter the E-mail account in the Print Server E-mail Address field. Then enter the server address, used to receive your E-mail here, in the Incoming E-mail (POP3) Server Address field. For Outgoing E-mail (SMTP) Server Address field, enter the server address that is used to send your E-mail here. If your mail server needs to verify the user when sending E-mail, Print Server will apply the E-mail Account (POP3) Name and E-mail Account (POP3) Password to the mail server. E-mail Printing This section is for you to do E-mail Printing configuration, including:

E-mail Printing (ASCII Text Only): Allows you to enable or disable the E-mail printing. Check E-mail Interval: Allow you to set up a time interval in minute in order to check/receive E-mail periodically. After done the configuration, click the Apply Settings button to restore the new configuration, or click Cancel to abandon. 76 ADVANCED > SNMP The SNMP screen allows you to use SNMP (Simple Network Management Protocol) to manage complex networks. SNMP Management Community 1/2/3: Enter a name in the Community 1/2/3 Name field, and configure the Access Right by selecting Read Only or Read/ Write from the drop-down menu. 77 MAINTENANCE > Password The Password screen allows you to change the password of the MFP server by entering the current password in Current Password field and new password in New Password and Confirm Password fields. After done the configuration, click the Apply Settings button to enable and restore the new password, or click Cancel to abandon. Be aware that the default password of the MFP server is blank. 78 MAINTENANCE > Save/Restore Settings The Save/Restore Settings screen not only allows you to save the current configuration in a computer for backup by clicking the Save button, but also allows you to reload a configuration that you saved before by clicking Browse to direct to the backup file, and then clicking Update Settings for reloading. Beside, you are also allowed to return the MFP server to the default settings by clicking Restore Device. 79 MAINTENANCE > Firmware Upgrade The Firmware Upgrade screen displays you the current firmwares information of the MFP server, and also allows you to upgrade the firmware of the MFP server when a new version of firmware is available. Click Browse to point to the firmware file, and then click Upgrade. 80 MAINTENANCE > Diagnostics The Diagnostics screen allows you to test the printing for the USB port of the MFP server. After done the port selection, click the Print Test Page button to print a test page. 81 STATUS > Device Info The Device Info screen displays the status of your MFP Server, printer, and network for your reference. 82 Print Server Status This field displays the information of the print server about the firmware version, MAC/IP address, and up time. Printer Status The items in this field display the information of the printer, such as the given name for the printer, speed, printer status, and status of your printing tasks, etc. LAN Status You can monitor the networking status in this field, including the network connection, speed, and the packets status. STATUS > Network The Network screen displays the general Network status of your MFP Server, including:

Auto IP This field contains the current settings of TCP/IP, including DHCP/BOOTP, UPnP, and Mac Bonjour/Rendezvous. The items in this field are configured in Advanced=>

Advanced LAN=> TCP/IP. TCP/IP Printing In this field, you can monitor the status of your printing tasks through TCP/IP. Microsoft Network Printing In this field, you can monitor the status of your printing tasks through Microsoft Network. Mac AppleTalk Printing In this field, you can monitor the status of your printing tasks through Mac AppleTalk. 83 84 STATUS >Print Log The Print Log screen displays the printing record of the authorized users. Print Log The items in this field display the user(s) information, which include the user(s) MAC address, IP address, name, and status of printing tasks. 85 HELP The Help screen provides you brief information about the MFP Server for your reference. 86 Reboot If you want to reset the MFP server, you may just click the Reboot for restarting. 87 Refresh Printer Status Click the printer on the left window to refresh printer status. 88 TCP/IP Printing for Windows Vista Go to Start=> Control Panel=> Printers. 89 Click Add a printer. Select the first option, Add a local printer, and then click Next. 90 Select the second option, Create a new port, and highlight Standard TCP/IP Port from the pull-down menu. Click Next. 91 Type the IP address of the MFP server (e.g. 10.62.31.15 used in this manual), which can be referred from the PRINTER SERVER STATUS of the MFP servers Web configuration, and then the Port Name will automatically be filled in. Click Next. 92

93 Highlight the printer, as shown. If the desired printer is not on the list, click Have Disk and insert the printer driver disk that came with your printer to install the printer drivers. Click Next 94 Click Next to start installing the printer. 95 After clicked Print a test page, a small dialogue box will show up as below. Click Close. 96 Click Finish. 97 The printer is now ready for printing with Windows Vista on your network. 98 TCP/IP Printing for Windows XP Go to Start => Printers and Faxes => Add a Printer. When the following screen shows up, click Next. 99 Select the first option, Local printer attached to this computer, and click Next. 100 Select the second option, Create a new port, and highlight Standard TCP/IP Port from the pull-down menu. Click Next. 101 Click Next. 102 Type the IP address of the MFP server (e.g. 10.62.31.15 used in this manual), which can be referred from the PRINTER SERVER STATUS of the MFP servers Web configuration, and then the Port Name will automatically be filled in. Click Next 103 Select Custom and click Settings. 104 Then the follow screen will shows up, select LPR from the Protocol field. Then enter the Queue Name, which can be referred from PRINTER STATUS of the MFP servers Web configuration, in the LPR Settings field. Click OK. 105 106 Click Next. 107 Click Finish. 108 Highlight the printer, as shown. If the desired printer is not on the list, click Have Disk and insert the printer driver disk that came with your printer to install the printer drivers. Click Next 109 At this screen, you can input a name for the printer, and then click Next 110 Select Yes to print a test page, click Next. Click Finish. The printer is now ready for printing with Windows XP on your network. 111 112 TCP/IP Printing for Windows 2000 Go to Start => Settings => Printers and Faxes => Add a Printer. When the following screen shows up, click Next. 113 Select the first option, Local printer attached to this computer, and click Next. 114 Click Next if New Printer Detection page pops up. Select the second option, Create a new port, and highlight Standard TCP/IP Port from the pull-down menu. Click Next. 115 Click Next. 116 Type the IP address of the MFP server (e.g. 10.62.31.15 used in this manual), which can be checked from the PRINTER SERVER STATUS of the MFP servers Web configuration, and then the Port Name will automatically be filled in. Click Next 117 Select Custom and click Settings. 118 Then the follow screen will shows up, select LPR from the Protocol field. Then enter the Queue Name, which can be referred from PRINTER STATUS of the MFP servers Web configuration, in the LPR Settings field. Click OK. 119 120 Click Next. 121 Click Finish. 122 Highlight the printer, as shown. If the desired printer is not on the list, click Have Disk and insert the printer driver disk that came with your printer to install the printer drivers. Click Next. 123 At this screen, you can input a name for the printer, and then click Next 124 Select the first option, Do not share this printer, and click Next. 125 Select Yes to print a test page, click Next. 126 Click Finish. The printer is now ready for printing with Windows 2000 on your network. 127 TCP/IP Printingfor Windows 98SE/ME Go to Start => Settings => Control Panel. Double click on Network, and then click Add. 128 Highlight Client and click Add. At this window, click Have Disk. 129 1. Insert the DPP-1061 CD-ROM into your CD-ROM drive. Select the letter representing the CD-ROM drive on your computer from the pull-down menu. 2. Double-click on the folder lpr. 3. Highlight lpr.inf 4. Click OK. Click OK to accept the location of the file. 130 You should now be back to the Network Properties Page. Highlight LPR for TCP/IP Printing and click Properties. 131 Click Add Port. 132 Type in the IP address and Port Name of the MFP server, which can be referred from the PRINTER SERVER STATUS and PRINTER STATUS of the MFP servers Web configuration, in the corresponding field, and then click OK. (The IP Address and Port Name here are just for example only.) 133 134 The IP Address and Port Name will be displayed in the following screen. (The IP Address and Port Name here are just for example only.) Click OK. 135 Click OK. 136 Windows will ask for a restart. Click Yes. Once your computer has rebooted, click on Start => Settings => Printers => Add Printer. When the Add Printer Wizard screen appears, click Next. 137 Select Network Printer and click Next. Type in the path if you know it; otherwise, click Browse. 138 At the following screen, browse for the printer port and highlight the port (e.g. dlink-1D6FA3 in this manual). Click OK. 139 If the network path is not specified, type in the IP Address and Port Name of the MFP server. Select Yes or No to enable or disable printing from MS-DOS based programs. Click Next. 140 Highlight the printer, as shown. If the desired printer is not on the list, click Have Disk and insert the printer driver disk that came with your printer to install the printer drivers. Click Next. 141 Click Next. Select Yes to print a test page. Click Finish. 142 To check whether the printer is installed, go to Start => Settings => Printers. 143 Unix/Linux Printing Printing Text Files form Unix Text files on Unix systems contain lines that end with newline characters, as opposed to MS-DOS and Windows-related operating systems that end with a carriage return followed by a linefeed. Most printers require a carriage return/linefeed pair at the end of each line, making it necessary for some translation to be done before Unix text files can be printed on most printers. For this purpose, you can define two printers for the same printer port, one that prints to the port itself, and one that prints to the port name with _TEXT added to the name. Files printed to the second port will be translated so that the printer has the carriage return/linefeed pairs that it needs. For example, you could define a printer hp5l that prints to port PS-142634-P1, and a printer hp5lt that prints to port PS-142634-P1_TEXT Your graphics files could then be printed to the hp5l printer, and raw text files could be printed to the hp5lt printer. 144 Printing form BSD Unix Versions For flavors of the Unix operating system derived from or related to the BSD releases, such as SunOS 4.x, Linux, BSD/OS, FreeBSD, or NetBSD, you can use the following procedure to enable users to print to a printer connected to your D-LINK network print server:

1. Log in as the superuser (root). 2. Add an entry for the print server in the hosts /etc/hosts file, giving a hostname for the print servers IP address. A line in /etc/hosts contains an IP address and one or more aliases for the host . For example:

202. 39. 74. 40 ps-142634 ps-142634.dlink.com.tw If you use DNS (the Domain Naming Services protocol), you can add an address record entry to your DNS database for the print server. 3. Create a spool directory for the printer:

On SunOS systems, create the directory as a subdirectory of /var/spool, with the same name as the printer (e.g., /var/spool/hp5l ).

On Linux systems, create the directory as a subdirectory of /user/spool

/lp.

On BSD/OS, FreeBSD, or NetBSD systems, create the directory as subdirectory of /var/spool. 4. Change the owner and permissions of the directory so that it is owned and writable by group 

, using the following commands:

145 chown bin.daemon /var/spool/hp5l chmod 775 /var/spool/hp5l 5. Add an entry for the printer to /etc/printcap, similar to the following:

hp5l:\

:lp=:sd=/var/spool/hp5l :mx#0:\

:rm=ps-142634:rp=ps-142634-p1:

The meaning of each of the entries is described below. The directory path in the

 spool directory entry should match the directory name you created above. If your entry requires more than one line you can escape the newline with a backslash. 6. Issue the command lpc start hp5l to start a spool daemon for the printer. The printer will now be available for use. 7. Optionally, add another printcap entry (and issue another lpc start command) for a second printer, using the port_TEXT port. This second printer name can be used for printing text files. Entries in /ect/printcap begin with a name for the printer or a list of name, separated by | (a vertical bar). The entries used above are:

lp= The lp entry is used to specify a local printer device. Since the printer is a remote printer, this entry should be blank. 145 sd=dir The location of the printers local spool directory. mx#blocks The limit for print job files in the local spool directory;

146

0 means no limit. rm=address The host where the remote printer is located, in this case the D-Link print server. rp=printer The name of the printer on the remote host. For the D-Link print server, the port name should be used. Note: this entry is case-sensitive. 147

Printing from SCO Unix System V/386 To allow printing to a printer attached to your D-LINK network print server from a SCO Unix System V/386 host. 1. Login as the superuser (root). 2. Add an entry for the print server in the hosts /etc/hosts file, giving a hostname for the print servers IP address. A line in /etc/hosts contains an IP address and one or more aliases for the host. For example:

202.39.74.40 ps-142634 ps-142634.dlink.com.tw If you use DNS (the Domain Naming Services protocol), you can add an address record entry to your DNS database for the print server. 3. Change to the /dev directory, and issue the command mkdev rlp 4. The script will ask:

Do you want to install or delet remote printing (i/d/q)?

Answer i and press Enter to continue. 5. The script will ask:

Do you want to change the remote printer description file

/etc/printcap (y/n)?

Answer y and press Enter to continue. 6. The script will ask:

Please enter the printer name (q to quit):

148 Enter an alias for the printer on the local machine and press Enter. This name should be the same as the destination port name. 7. Answer r (remote printer) to the question Is printer a remote printer or a local printer (r/l)?

8. When prompted with the question:

Please enter the name of the remote host that printer is attached to:

then enter the address of the D-Link print server. You can use the name you added to /etc/host in the step above. 9. Confirm that your entries are correct. Is this correct? (y/n) 10. Answer the question:

Would you like this to be the system default printer? (y/n) 11. When you are done adding remote printers, enter q for the printer name. 12. Answer y to the question Do you want to start remote daemon now (y/n)?

Once remote printing is set up, you can use the lp command to print jobs to the new printer. For more information, consult your SCO Unix documentation. 149 Printing from Solaris To allow printing from a Sun Solaris workstation, 1. Log in as the superuser (root). 2. Add an entry for the print server in the hosts /etc/hosts file, giving a hostname for the print servers IP address. A line in /etc/hosts contains an IP address and one or more aliases for the host . For example:

202.39.74.40 ps-142634 ps-142634.dlink.com.tw If you use DNS (the Domain Naming Services protocol), you can add an address record entry to your DNS database for the print server. 3. In OpenWindows, start the admintool program. 4. Click on the Printer Manger icon. 5. From the Edit menu, select Add Print, then Add Access to Remote Printer 6. Enter values for the fields as follow:

Printer Name This field should contain the name of the printer port you wish to use. The field is case-sensitive.

Printer Server This field should contain the IP address of the print server, or the alias name you added in step 2.

Printer Server OS This field should be set to BSD. 7. Confirm the addition. 8. Optionally repeat the addition to add another printer for printing text files, with_TEXT appended to the port name. Once you have added the new printer, you can use the lp command to print files to the printer. Consult your Solaris documentation for details. 150 Printing from Red Hat Linux Adding a Printer 1. Click the printer icon at the bottom of the desktop. 2. Since no printer is set up so far, a prompt appears asking to run the printer configuration tool. 151 3. Click the OK button in the pop-up dialogue box to open the man Printer configuration tool menu. Note that to use the Printer configuration tool you must have root privileges, and to start the application you may also type the command:

redhat-config-printer. 4. Click the New button in the Printer configuration tool menu. 152 Printer Configuration Tool menu 5. The Add a new print queue menu appears, click Forward to continue. 153 6. Enter a unique name for the printer in the Name text field. The printer name cannot contain spaces and must begin with a letter. The printer name may contain letters, numbers, dashes (-), and underscores (_). Optionally, enter a short description for the printer, which can contain spaces. Then click Forward to enter Queue type window. 7. Select Networked UNIX (LPD) in the Select a queue type pull down menu, enter the IP address of the print server to which the printer is attached in Server field, and type the port name in queue field. Click Forward to select the type of printer. 154 8. Select the printer model. 155 If a printer has not been detected automatically, select the model from the list. You can manually select the name of the printer manufacturer from the Generic (click to select manufacturer) pull-down menu, and the printer model from the sub-list. Click Forward to continue. 9. The last step is to confirm your printer configuration. Click Apply button to confirm or Back button to modify the configuration. 156 10. Print a test page to make sure the printer is functioning properly. To print a test page, select the printer from the printer list, then select the appropriate test page from the Test drop-down menu. 157 Setting up Printing in Mac OS X Tiger(10.4.9) NOTE: Mac OS printing is supported by Postscript printers only!

With Mac OS X Tiger (10.4), you can use Apple Talk, Bonjour, Internet Printing Protocol (IPP), Line Printer Daemon (LPD), and HP Jet Direct-Socket printing through Print Server. Click on this icon Preferences window as below. in your Dock to open your System Click on the Network icon in System Preferences menu to view the menu below. 158 Select the Apple Talk tab in the Network menu. Check to select the Make Apple Talk Active option. Click on the Apply Now button and close the menu. Apple Talk is now active on the system. Now a printer can be added. Adding a Printer Use the Go menu at the top tool bar and select Applications option and find the Utilities folder or open the Utilities folder directly in Go menu. 159 In the Utilities folder, find and select List dialog window. to see the Printer 160 Click Add button to open Printer Browser window. Mac OS X Tiger (10.4) supports five printing protocols:

1. AppleTalk 2. Bonjour 3. Internet Printing Protocol (IPP) 4. Line Printer Daemon (LPD) 5. HP Jet Direct Socket To add an Internet Printing Protocol enabled, Line Printer Daemon enabled or HP Jet Direct Socket enabled printer, click on the button and follow the instructions to add an IP Printer beginning on Adding an IP printer session. 161 AppleTalk-enabled or Bonjour-enabled Printers To add an AppleTalk-enabled or Bonjour-enabled printer, click the button in the Printer Browser menu. Select the printer model from Printer Name list and Connection type in the Printer Browser menu. The printer name selected should be the same as that appearing listed in the Printer Servers web manager. In the example here, the printer name is 162 dlk-C352AB-U1. By default the Printer Browser will use the Auto Select for Print Using: to determine what printer configuration to use. This may also be manually selected in the Print Using drop-down menu by brand and model. Click the Add button to exit the Printer Browser window and implement the new setting. 163 The printer that has just been added will show up in the Printer List menu, it might take a few seconds depending on network conditions. When the printer appears listed it is ready for use. Quit the Printer Setup Utility and start printing. 164 Adding an IP Printer To add an Internet Printing Protocol enabled, Line Printer Daemon enabled or HP Jet Direct Socket enabled printer, click the button in the Printer Browser window. Select a desired printing protocol from the Protocol drop-down menu. 165 Type the IP Address of the printer. The name will appear in the Name field when the printer is found. The Printer Browser will indicate that it is verifying the address. If the printer is found, the Printer Browser will state Valid and complete address in the Address field. The printer utility is able to detect the printer and may automatically select the correct printer driver in the Print Using field. Or manually select the printer-maker from the Print Using drop-down menu, and then select the printer model from the scroll-down list, or select Generic PostScrip Printer option from the Print Using drop-down menu if the model is not listed. To implement the setting, click Add button. The setup procedures for these three printing protocols (Internet Printing Protocol

(IPP), Line Printer Daemon (LPD), and HP Jet Direct Socket) are basically the same. Illustrated examples are include below for the sake of reference. 166 For set up LPD Printing:

1. Enter the IP address of the print server to which the printer is attached in Address field. 2. Type the port name in the Queue field. Click Add button after done the section of printer model in the Print Using drop-down menu. For set up IPP Printing:

1. Enter the IP address of the print server to which the printer is attached in 167 Address field. After that, type : 80 or : second port if print servers second port is enabled. 2. Type the port name in the Queue field. Click Add button after done the section of printer model in the Print Using drop-down menu. For set up Socket Printing:

1. Enter the IP address of the print server to which the printer is attached in Address field. After that, type : 9100 for port 1, : 9101 for port 2 or : 9102 168 for port 3. 2. Keep the blank in Queue field. Click Add button after done the section of printer model in the Print Using drop-down menu. 169 When the Installable Options pop-up window shows up as below, click Continue button. The printer that has just been added will show up in the Printer List menu, it might take a few seconds depending on network conditions. When the printer appears listed it is ready for use. Quite the Printer Setup Utility and start printing. 170 171 Setting up AppleTalk Printing in Mac OS 9

: Mac OS printing is supported by Postscript printers only!

The AppleTalk network protocol is used with computers using the MacOS operating system. It can be used for network communications over standard Ethernet or Fast Ethernet using the EtherTalk transport, or over a proprietary low-speed LocalTalk transport. MFP server can be used for network printing to PostScript printers. You can print from any MacOS computer connected to your Ethernet network, either directly using an EtherTalk connection, or indirectly through a LocalTalk-to-EtherTalk router.

: The Chooser name of a printer connected to one of the Print Servers ports is the same as its Port Name. If you are using AppleTalk printing, you will need to make sure that every Port Name is unique among all of the network printers in your AppleTalk zone. The Port Names shown in this manual are examples only. To set up MFP server so that it can be used for AppleTalk printing:

Make sure the AppleTalk protocol is enabled in your Macintosh.

Make sure the PCs IP Address must correspond with the Print Servers IP Address in the same segment for the two devices to communicate.

Launch the browser and enter print server web interface, select the ADVANCED tab, click Advanced LAN button and then scroll to the bottom to the AppleTalk protocol section

If your AppleTalk network is divided into AppleTalk zones, you will have to specify which zone the Print Server should be in. You should locate the Print Server in the same zone as most of the users who will be using it. If your network is not divided into zones, the AppleTalk Zone field should contain a single asterisk (*). 172 For each Printer Port that will be used for AppleTalk printing, you may need to change the AppleTalk Port Settings in the Advanced LAN screen, shown as below. AppleTalk Enter the AppleTalk Zone name in the box. In the following options, enter the related configuration, such as the printer type. Chooser Name: Display the print server's port name. Printer Type: Enter the printer's type in this box. PostScript Level: Select from the pull-down menu (Level 1 or Level 2). 173 Font Group: Select from the pull-down menu. The exact procedure for selecting a PostScript printer connected to MFP server may vary slightly, depending on what printer driver version you are using. The procedure described below assumes you are using the LaserWriter 8. To choose a printer connected to MFP server as your MacOS workstations default printer, open the Chooser by selecting Chooser from the Apple menu. Select the LaserWriter 8 icon on the left. Make sure that AppleTalk is set to Active. A list of all networked PostScript printers will be displayed as follow. Double-click the name of the Printer Port you wish to use. The Printer Ports shown are examples only. If you have not previously set this printer as the default, your computer will prompt you for a PostScript Printer Description file. Choose Select PPD. 174 Select the appropriate printer description file for your printer. Click Open. (If your printer is not listed, click Generic to use a generic printer description.) If you wish to access this setting in the future, you can use the Setup button in the Chooser window. The selected printer will become your computers default printer. You may need to choose Page Setup in any applications you have open. 175 Technical Specifications Printer Connection Printer Port: USB 2.0 Bi-directional Communication: Hewlett-Packard PJL (Printer Job Language) standard for bi-directional communication. Network Connection Network Standards: 100Base-TX Fast Ethernet Network Data Transfer Rate: 10/100 Mbps (megabits per second) Network Connector: RJ-45 Network Protocols Ethernet Frame Types: 802.2, 802.3, Ethernet II, SNAP (auto-switching) Transport Protocols: TCP/IP, NetBEUI, AppleTalk/EtherTalk, LPR,SMB TCP/IP Protocols Supported: BOOTP, SNMP, FTP, LPD, RARP, DHCP, IPP Management and Diagnostics Standard: SNMP MIBs: MIB-II (RFC 1213) Diagnostic LED Indicators: Power, Link/Act, USB Environmental and Physical Power Supply: External power supply providing 5V, 2.5A DC Dimensions: 58.1(W) x 26.5(H) x 90(D)mm Weight: approx. 10.3 oz. (292g) Operating Temperature: 32 to122F (0 to 50C) Storage Temperature: -13 to 131F (-25 to 55C) Humidity: 5% to 95% non-condensing Emissions: FCC Class B, CE Class B, VCCI Class B 180 176 Contacting Technical Support 181 Warranty and Registration Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (D-Link) provides this Limited warranty for its product only to the person or entity that originally purchased the product from:

D-Link or its authorized reseller or distributor and

Products purchased and delivered within the fifty states of the United States, the District of

Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an APO or FPO. Limited Warranty: D-Link warrants that the hardware portion of the D-Link products described below will be free from material defects in workmanship and materials from the date of original retail purchase of the product, for the period set forth below applicable to the product type (Warranty Period), except as otherwise stated herein. 1-Year Limited Warranty for the Product(s) is defined as follows:

Hardware (excluding power supplies and fans) One (1) Year

Power Supplies and Fans One (1) Year

Spare parts and spare kits ninety (90) days. D-Links sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund at D-Links sole discretion. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be new or have an identical make, model or part. D-Link may in its sole discretion replace the defective Hardware

(or any part thereof) with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or replacement Hardware will be warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a material defect is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to repair or replace the defective Hardware, the price paid by the original purchaser 177 for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund. Limited Software Warranty: D-Link warrants that the software portion of the product (Software) will substantially conform to D-Links then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety

(90)days (Warranty Period), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. D-Links sole obligation shall be to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Links functional specifications for the Software or to refund at D-Links sole discretion. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Software will be warranted for the remainder of the original Warranty Period from the date or original retail purchase. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates. Non-Applicability of Warranty: The Limited Warranty provided hereunder for hardware and software of D-Links products will not be applied to and does not cover any refurbished product and any product 182 purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold As-Is without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary. Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the 178 customer shall submit a claim to D-Link as outlined below:

The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same.

The original product owner must obtain a Return Material Authorization (RMA) number from the Authorized D-Link Service Office and, if requested, provide written proof of purchase of the product (such as a copy of the dated purchase invoice for the product) before the warranty service is provided.

After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the Product and will not ship back any accessories.

The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (COD) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 53 Discovery Drive, Irvine, CA 92618. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link, with shipping charges prepaid. Expedited shipping is available if shipping charges are prepaid by the customer and upon request. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Links reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming. What Is Not Covered: This limited warranty provided by D-Link does not cover: Products, if in D-Links judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, 179 misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal maintenance;

Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage;

Any hardware, software, firmware or other products or services provided by anyone other than D-Link;

Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product. Repair by anyone other than D-Link or an Authorized D-Link Service Office will void this Warranty. Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THEPRODUCT IS PROVIDED AS-IS WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSEAND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANYTERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO NINETY (90) DAYS. EXCEPTAS EXPRESSLY 183 COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRERISK AS TOTHE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OFTHE PRODUCT. Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDERANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANYLOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OFGOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINKS PRODUCT IS CONNECTEDWITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY 180 PRODUCTRETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATINGTO WARRANTYSERVICE, OR ARISING OUT OFANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINKHAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BYTHE WARRANTY.THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY. Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific legal rights and the product owner may also have other rights which vary from state to state. Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective manufacturers or owners. Copyright Statement: No part of this publication or documentation accompanying this Product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976. Contents are subject to change without prior notice. Copyright 2002 by D-Link Corporation/ D-Link Systems, Inc. All rights reserved. CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate 181 radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for 184 compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of about 8 inches (20 cm) between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. 182 NCC Warning Statement Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery. Article 14 The application of low power frequency electric machineries shall not affect the navigation safety nor interfere a legal communication, if an interference is found, the service will be suspended until improvement is made and the interference no longer exists. 183