FCC ID: KA2WR113A1 3G WiFi Router

Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies. Copyright 2010 by D-Link Systems, Inc. All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Systems, Inc. D-Link DWR-113 User Manual i Table of Contents Table of Contents Preface...........................................................................i Trademarks .............................................................. i Product Overview ........................................................1 Package Contents ................................................... 1 System Requirements ............................................. 1 Introduction ..............................................................2 Hardware Overview ................................................. 3 Back Panel ......................................................... 3 Front Panel and LEDs ....................................... 4 Installation ....................................................................5 Connect to Your Network ........................................ 5 Wireless Installation Considerations ........................ 6 Configuration ...............................................................7 Web-based Configuration Utility .............................. 7 Setup Wizard ...........................................................8 Internet Connection Setup Wizard ..................... 8 Manual Internet Connection Setup .................. 12 Internet Connection ......................................... 13 Internet Connection Type ................................ 13 Dynamic IP (DHCP) ......................................... 14 PPPoE ............................................................. 15 PPTP ............................................................... 16 L2TP ................................................................ 17 3G .................................................................... 18 Static IP ........................................................... 19 Wireless Settings ............................................. 20 Network Settings .............................................. 22 Router Settings ............................................22 DHCP Server Settings ................................. 23 Virtual Server ................................................... 24 Application Rules ............................................. 25 QoS Engine ..................................................... 26 MAC Address Filter .......................................... 27 URL Filter ......................................................... 28 Outbound Filter ................................................ 29 Inbound Filter ................................................... 30 SNMP .............................................................. 31 Routing ............................................................ 32 Advanced Wireless .......................................... 33 Advanced Network ........................................... 34 Admin ............................................................... 35 Time .................................................................36 Syslog .............................................................. 37 E-mail Settings ................................................. 38 System ............................................................. 39 Firmware .......................................................... 40 Dynamic DNS .................................................. 41 System Check .................................................. 42 Schedules ........................................................ 43 Device Information ........................................... 44 D-Link DWR-113 User Manual ii Technical Specifications...........................................71 Table of Contents Logs ................................................................. 45 Statistics .......................................................... 46 Wireless ........................................................... 47 Support ............................................................ 48 Wireless Security.......................................................49 What is WEP? .......................................................49 Configure WEP ......................................................50 What is WPA? .......................................................51 Configure WPA-PSK ............................................. 52 Configure WPA (RADIUS) ..................................... 53 Connect to a Wireless Network ................................54 Using Windows Vista ......................................... 54 Configure Wireless Security ............................ 55 Using Windows XP ............................................... 57 Configure WEP ................................................ 58 Configure WPA-PSK ........................................ 60 Troubleshooting ........................................................62 Wireless Basics .........................................................64 What is Wireless? .................................................. 65 Tips ........................................................................ 67 Wireless Modes .....................................................68 Networking Basics ....................................................69 Check your IP address .......................................... 69 Statically Assign an IP address ............................. 70 D-Link DWR-113 User Manual iii Section 1 - Product Overview Product Overview Package Contents D-Link DWR-113 3G Wi-Fi Router Power Adapter Manual and Warranty on CD External Wi-Fi antenna Note: Using a power supply with a different voltage rating than the one included with the DWR-113 will cause damage and void the warranty for this product. System Requirements A compatible 3G USB modem Computers with Windows, Macintosh, or Linux-based operating systems with an installed Ethernet adapter Internet Explorer Version 6.0 or Netscape Navigator Version 6.0 and above (for configuration) D-Link DWR-113 User Manual 1 Section 1 - Product Overview Introduction The D-Link 3G Wi-Fi Router allows users to access worldwide mobile broadband networks. Once connected, users can transfer data, stream media, and send SMS messages. Simply connect your USB modem and share your 3G Internet connection through a secure 802.11n wireless network or using the 10/100 Ethernet port. While accessing your 3G Internet connection, you will still have the ability to respond to SMS messages. The 3G Wi-Fi Router can be installed quickly and easily almost anywhere. This router is great for situations where an impromptu wireless network must be set up, or wherever conventional network access is unavailable. The DWR-113 can even be installed in buses, trains, or boats, allowing passengers to check e-mail or chat online while commuting. D-Link DWR-113 User Manual 2 Section 1 - Product Overview Hardware Overview Back Panel LAN 3 LAN 1 LAN 4 LAN 2 POWER WAN USB Port USB Port LAN Port WAN Port Power Port Function Connects to a USB modem. Connects to wired computers or devices. Connects to the Internet. Connects to the power adapter. D-Link DWR-113 User Manual 3 Section 1 - Product Overview Hardware Overview Front Panel and LEDs WAN LAN LAN 3G Wi-Fi LAN LAN RESET BUTTON WPS BUTTON LED 3G WAN Wi-Fi Description Color Solid Green 3G connection established Green WAN connection established Green Wi-Fi active and available LAN 1 - LAN 4 Green Ethernet connection established Data transmitting D-Link DWR-113 User Manual 4 Blinking Data transmitting Data transmitting Data transmitting Device in WPS Blinking (Fast)

-

-

mode

-

Section 2 - Installation Installation This section will guide you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in an attic or garage. Connect to Your Network Note: Ensure that your DWR-113 3G Wi-Fi Router is disconnected and powered off before performing the installation steps below. 1. Connect a USB modem to the USB port on the back of the router. 2. Insert a LAN network cable into the LAN port on the back of the router. Plug the other end of the LAN cable into the LAN port of your computer or laptop. The Ethernet LED will turn green if the Ethernet connection is successfully established. Note: The DWR-113 3G Wi-Fi Router LAN Port is Auto-MDI/MDIX. Therefore, patch or crossover Ethernet cables can be used. 3. Configure the device using the setup utility. D-Link DWR-113 User Manual 5 Section 2 - Installation Wireless Installation Considerations The DWR-113 can be accessed using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the quantity, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or office. The key to maximizing the wireless range is to follow these basic guidelines:

1. Minimize the number of walls and ceilings between the D-Link router and other network devices. Each wall or ceiling can reduce your adapters range from 3 to 90 feet (1 to 30 meters). 2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (0.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick. Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception. 3. Try to position access points, wireless routers, and computers so that the signal passes through open doorways and drywall. Materials such as glass, metal, brick, insulation, concrete and water can affect wireless performance. Large objects such as fish tanks, mirrors, file cabinets, metal doors and aluminum studs may also have a negative effect on range. 4. If you are using 2.4 GHz cordless phones, make sure that the 2.4 GHz phone base is as far away from your wireless device as possible. The base transmits a signal even if the phone in not in use. In some cases, cordless phones, X-10 wireless devices, and electronic equipment such as ceiling fans, fluorescent lights, and home security systems may dramatically degrade wireless connectivity. D-Link DWR-113 User Manual 6 Section 3 - Configuration Configuration This section will show you how to configure your new D-Link mobile router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router

(192.168.0.1). Type Admin and then enter the password. By default, the password is blank. If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance. D-Link DWR-113 User Manual 7 Section 3 - Configuration Setup Wizard The setup wizard guides you through the initial setup of your router. There are two ways to setup your Internet connection. You can use the Web-based Internet Connection Setup Wizard or you can manually configure using the Manual Internet Connection Setup wizard. Click Internet Connection Setup Wizard to begin. If you want to enter your settings without running the wizard, click Manual Internet Connection Setup and skip to page 13. Internet Connection Setup Wizard This wizard will guide you through a step-by-step process to configure your D-Link router to connect to the Internet. Click Next to continue. D-Link DWR-113 User Manual 8 Section 3 - Configuration Create a new password and then click Next to continue. Click Prev to go back to the previous page or click Cancel to close the wizard. Select your time zone from the drop-down box and then click Next to continue. Click Prev to go back to the previous page or click Cancel to close the wizard. Select the Internet connection type. The connection types are explained on the following page. If you are unsure of the correct connection type, you may have to contact your Internet Service Provider (ISP). Click Prev to go back to the previous page or click Cancel to close the wizard. Note: The DWR-113 supports several kinds of WAN interfaces, allowing you to assign either a WAN or a WWAN(3G) connection as the Backup WAN. If the Primary WAN is down or unavailable, configure the Backup WAN to Enable, and all the traffic will be routed through Backup WAN. This feature is called WAN Failover. You can use WAN Failover if you need redundancy to your Internet connection or any other network. D-Link DWR-113 User Manual 9 Section 3 - Configuration The subsequent configuration pages will differ depending on the selection you make on this page. DHCP Connection

(Dynamic IP Address):

Choose this if your Internet connection automatically provides you with an IP Address. Most cable modems use this type of connection. See page 16 for information about how to configure this type of connection. Username / Password Connection (PPPoE):

Choose this option if your Internet connection requires a username and password to connect. Most DSL modems use this style of connection. See page 17 for information about how to configure this type of connection. Username / Password Connection (PPTP):

Choose this option if your Internet connection requires Point-to-Point Tunneling Protocol (PPTP). See page 18 for information about how to configure this type of connection. Username / Password Connection (L2TP):

Choose this option if your Internet connection requires Layer 2 Tunneling Protocol (L2TP). See page 19 for information about how to configure this type of connection. Static IP Address Connection:

Choose this option if your Internet Setup Provider provided you with IP Address information that has to be manually configured. See page 21 for information about how to configure this type of connection. D-Link DWR-113 User Manual 10 Section 3 - Configuration You have completed the Setup Wizard. Click Connect to save your settings. A popup will appear, to confirm your settings. Click OK to save your settings. D-Link DWR-113 User Manual 11 Section 3 - Configuration Manual Internet Connection Setup Click Manual Internet Connection Setup to begin. If you want to configure your router to connect to the Internet using the wizard, click Internet Connection Setup Wizard and refer to page 9. D-Link DWR-113 User Manual 12 Section 3 - Configuration Internet Connection Internet Connection Type Several different Internet Connection types can be selected depending upon the specifications of your Internet Service Provider (ISP). My Internet Connection is:

Select the Internet Connection type specified by your Internet Service Provider (ISP). The corresponding settings will be displayed below. Please see the following pages for details on how to configure these different connection types. Failover Internet Connection is:

This connection can serve as a backup for your default connection. Host Name:

Enter the name of the Internet host to be used as the backup connection. Primary DNS Server:

Enter the primary DNS server. Secondary DNS Server:

Enter the secondary DNS server. MTU:

Set the MTU (the default value is 1500). MAC Address:

Manually enter the MAC address or click Clone to copy the PCs MAC address. Auto-reconnect:

Tick this check box to enable auto-

reconnect. D-Link DWR-113 User Manual 13 Section 3 - Configuration Dynamic IP (DHCP) This section will help you to obtain IP Address information automatically from your ISP. Use this option if your ISP didnt provide you with IP Address information and/or a username and password. Host Name:

(Optional) Required by some ISPs. Primary DNS Server:

Secondary DNS Server:

MTU (Maximum Transmission Unit):

MAC Address:

Auto-reconnect:

(Optional) Fill in with IP address of primary DNS server.

(Optional) Fill in with IP address of secondary DNS server. You may need to change the Maximum Transmission Unit (MTU) for optimal performance. The default value is 1500. The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PCs MAC Address button to replace the Internet ports MAC address with the MAC address of your PC. This feature enables this product to renew WAN IP address automatically when the lease time is expiring. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 14 Section 3 - Configuration Choose this Internet connection if your ISP provides you PPPoE account. PPPoE Username:

Password:

Verify Password:

The username/account name that your ISP provides to you for PPPoE dial-up. Password that your ISP provides to you for PPPoE dial-up. Fill in with the same password in Password field. Service Name:

(Optional) Fill in if provided by your ISP. IP Address:

Primary DNS Server:

Secondary DNS Server:

MAC Address:

Maximum Idle Time:

Maximum Transmission Unit (MTU):

(Optional) Fill in if provided by your ISP. If not, keep the default value.

(Optional) Fill in if provided by your ISP. If not, keep the default value.

(Optional) Fill in if provided by your ISP. If not, keep the default value. MAC address of WAN interface. You can also copy MAC address of your PC to its WAN interface by pressing Clone Your PCs MAC button. The Restore MAC button will reset the router to its default MAC address. The amount of time of inactivity before disconnecting established PPPoE session. Set it to zero or enable Auto-reconnect will disable this feature. The default setting of PPPoE is 1492. Auto-reconnect:

The device will dial-up PPPoE connection automatically. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 15 Section 3 - Configuration PPTP Choose this Internet connection if your ISP provides you PPTP account. Address Mode:

PPTP IP Address:

PPTP Subnet Mask:

PPTP Gateway IP Address:

PPTP Server IP Address:

Choose Static IP only if your ISP assigns you an IP address. Otherwise, please choose Dynamic IP. Enter the information provided by your ISP.

(Only applicable for Static IP PPTP.) Enter the information provided by your ISP.

(Only applicable for Static IP PPTP.) Enter the information provided by your ISP.

(Only applicable for Static IP PPTP.) IP address of PPTP server. Username:

User/account name that your ISP provides to you for PPTP dial-up. Password:

Password that your ISP provides to you for PPTP dial-up. Verify Password:

Fill in with the same password in Password field. Reconnect Mode:

Choose Always-on when you want to establish PPTP connection all the time. If you choose Connect-on-

demand, the device will establish PPTP connection when local users want to surf Internet, and disconnect if no traffic after time period of Maximum Idle Time. Maximum Idle Time:

The time of no activity to disconnect your PPTP session. Set it to zero or choose Always-on to disable this feature. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 16 Section 3 - Configuration L2TP Choose this Internet connection if your ISP provides you L2TP account. Address Mode:

L2TP IP Address:

L2TP Subnet Mask:

L2TP Gateway IP Address:

L2TP Server IP Address:

Choose Static IP only if your ISP assigns you an IP address. Otherwise, please choose Dynamic IP. Enter the information provided by your ISP.

(Only applicable for Static IP L2TP.) Enter the information provided by your ISP.

(Only applicable for Static IP L2TP.) Enter the information provided by your ISP.

(Only applicable for Static IP L2TP.) IP address of L2TP server. Username:

User/account name that your ISP provides to you for L2TP dial-up. Password:

Password that your ISP provides to you for L2TP dial-up. Verify Password:

Fill in with the same password in Password field. Reconnect Mode:

Choose Always-on when you want to establish L2TP connection all the time. Choose Connect-on-demand the device will establish L2TP connection when local users want to surf Internet, and disconnect if no traffic after time period of Maximum Idle Time. Maximum Idle Time:

The time of no activity to disconnect your L2TP session. Set it to zero or choose Always-on to disable this feature. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 17 Section 3 - Configuration 3G Choose this Internet connection if you already use a SIM card for 3G Internet service from your Telecom company. The fields here may not be necessary for your connection. The information on this page should only be used if required by your service provider. Account/Profile Name:

Username:

Fill in a name to indicate the following 3G configuration.

(Optional) Fill in only if requested by ISP. Password:

(Optional) Fill in only if requested by ISP. Dialed Number:

Enter the number to be dialed. Authentication:

APN:

PAP, CHAP, or Auto detection. The default authentication method is Auto.

(Optional) Enter the APN information. PIN:

Enter the PIN associated with your SIM card. Reconnect Mode:

Auto or Manual. Connect to 3G network automatically or manually. Maximum Idle Time:

Primary DNS Server:

The time of no activity to disconnect established 3G session. Set it to zero or choose Auto in Reconnect Mode to disable this feature.

(Optional) Fill in if provided by your ISP. If not, keep the default value. Secondary DNS Server:

(Optional) Fill in if provided by your ISP. If not, keep the default value. Keep Alive:

Disable or Use LCP Echo Request. It depends on ISP requirement. Bridge Ethernet Ports:

Activate this feature to change Ethernet WAN port to LAN port. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 18 Section 3 - Configuration Choose this Internet connection if your ISP assigns you a static IP address. Static IP IP Address:

Subnet Mask:

Enter the IP address assigned to your network connection. Enter the subnet mask. Default Gateway:

Enter the default gateway. Primary DNS Server:

Enter the primary DNS server. Secondary DNS Server:

Enter the secondary DNS server. MTU:

You may need to change the Maximum Transmission Unit (MTU) for optimal performance. The default value is 1500. MAC Address:

The default MAC Address is set to the Internet ports physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PCs MAC Address button to replace the Internet ports MAC address with the MAC address of your Ethernet card. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 19 Section 3 - Configuration This section will help you to manually configure the wireless settings of your router. Please note that changes made on this section may also need to be duplicated on your Wireless Client. Wireless Settings Enable Wireless:

Wireless Network Name:

802.11 Mode:

WIRELESS NETWORK SETTINGS Select this checkbox to enable wireless access. When you set this option, the following parameters take effect. Also known as the SSID (Service Set Identifier), this is the name of your Wireless Local Area Network

(WLAN). Enter a name using up to 32 alphanumeric characters. The SSID is case-sensitive. The default name is dlink_DWR-113. B/G/N mixed: Enable this mode if your network contains a mix of 802.11b and 802.11g devices. G mode: Enable this mode if your network has only 802.11g devices. If you have both 802.11b and 802.11g wireless clients, disable this mode. Auto Channel Scan:

A wireless network uses specific channels in the wireless spectrum to handle communication between clients. Some channels in your area may experience interference from other electronic devices. Choose the clearest channel to help optimize the performance and coverage of your wireless network. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 20 Section 3 - Configuration Wireless Channel:

Visibility Status:

Indicates the channel setting for the DWR-113. By default the channel is set to 11. This can be changed to fit the channel setting for an existing wireless network or to customize your wireless network. Click Auto Channel Scan to automatically select the channel that it will operate on. This option is recommended because the router will choose the channel with the least amount of interference. Select Invisible if you do not want the SSID of your wireless network to be broadcasted by DWR-113. The SSID of your router will not be seen by Site Survey utilities. Therefore while setting up your wireless clients, you will have to manually enter your SSID to connect to the router. WIRELESS SECURITY MODE Security Mode:

This device supports three wireless security modes, WEP, WPA-Personal, WPA-Enterprise or None. WEP is the original wireless encryption standard. WPA provides a higher level of security and WPA-Personal does not require an authentication server. When WPA enterprise is enabled, the router uses EAP (802.1x) to authenticate clients via a remote RADIUS server. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 21 Section 3 - Configuration This section will help you to change the internal network settings of your router and to configure the DHCP Server settings. Network Settings Router Settings Router IP Address:

Enter the IP address of the router. The default IP address is 192.168.0.1. Default Subnet Mask:

Local Domain Name:

If you change the IP address, you will need to enter the new IP address in your browser to get into the configuration utility. Enter the Subnet Mask of the router. The default subnet mask is 255.255.255.0. Enter the local domain name for your network. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 22 Section 3 - Configuration DHCP Server Settings The DWR-113 has a built-in DHCP (Dynamic Host Control Protocol) server. The DHCP server assigns IP addresses to devices on the network that request them. By default, the DHCP Server is enabled on the device. The DHCP address pool contains a range of IP addresses, which is automatically assigned to the clients on the network. Enable DHCP Server:

DHCP IP Address Range:

DHCP Lease Time:

Primary DNS IP Address:

Select this box to enable the DHCP server on your router. Enter the starting and ending IP address for the servers IP assignment. The time period for the IP address lease. Enter the Lease time in minutes. Primary DNS IP Address: assign a primary DNS Server to DHCP clients. Secondary DNS IP Address:

Secondary DNS IP Address: assign a DNS Server to DHCP clients. Primary WINS IP Address:

Primary WINS IP Address: assign a primary WINS Server to DHCP clients. Secondary WINS IP Address:

Secondary WINS IP Address: assign a WINS Server to DHCP clients. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 23 Section 3 - Configuration The device can be configured as a virtual server so that users can access services such as Web or FTP via the public (WAN) IP address of the router. Virtual Server Well-known Services:

Copy to:

Use schedule rule:

This contains a list of pre-defined services. Copies the rule to the line of the specified ID. You may select Always On or choose the number of a schedule rule that you have defined. VIRTUAL SERVERS LIST ID:

Identifies the virtual server. Server IP: Port:

Enable:

Enter the last digits of the IP address of the computer on your local network that you want to allow the incoming service. In the next box, enter the port number that you would like to open. Select this box to enable the rule. Schedule Rule #:

Specify the schedule rule number. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 24 Section 3 - Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Applications Rules allow some of these applications work with the DWR-113. Popular Applications:

Copy to ID:

APPLICATION RULES Select from a list of popular applications. Copies the predefined application rule to the line of the specified ID. ID:

Identifies the rule. Trigger:

The name of the trigger. Incoming Ports:

Enable:

Specify the incoming port for the trigger rule. Select this box to enable the rule. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 25 Section 3 - Configuration QoS Engine The QoS Engine improves your online gaming experience by ensuring that your game traffic is prioritized over other network traffic, such as FTP or Web. For best performance, use the Automatic Classification option to automatically set the priority for the applications. QoS ENGINE SETUP Enable QoS Packet Filter:

Upstream Bandwidth:

Select this box to enable the QoS Packet Filter. Specify the maximum upstream bandwidth here (e.g. 400 kbps). QoS RULES Identifies the rule. ID:

Local IP : Ports:

Specify the local IP address and then specify the port after the colon. Remote IP : Ports:

QoS Priority:

Specify the remote IP address and then the port after the colon. Select Low, Normal, or High. Enable:

Select a checkbox to enable the particular QoS rules individually. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 26 Section 3 - Configuration MAC Address Filter The MAC (Media Access Controller) Address Filter option is used to control network access based on the MAC Address of the network adapter. A MAC address is a unique ID assigned by the manufacturer of the network adapter. This feature can be configured to ALLOW or DENY network/Internet access. MAC FILTERING SETTINGS MAC Address Control:

Select this box to enable Mac Filtering. Connection Control:

Association Control:

Wireless and wired clients with C selected can connect to this device and allow/deny connections from unspecified MAC addresses. Wireless clients with A selected can associate to the wireless LAN; and allow/deny connections from unspecified MAC addresses. MAC FILTERING RULES ID:

Identifies the rule. MAC Address:

IP Address:

Specify the MAC Address of the computer to be filtered. Specify the last section of the IP address. Wake On LAN:

Click Trigger to configure Wake On LAN. C:

A:

If this box is selected, the rule will follow the connection control setting specified in MAC filtering settings. If this box is selected, the rule will follow the connection control setting specified in MAC filtering settings. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 27 Section 3 - Configuration URL Filter allows you to set up a list of Web-sites that will be blocked from users on your network. URL Filter URL Filtering:

Select this box to enable URL Filtering. ID:

URL:

Enable:

URL FILTERING RULES Identifies the rule. Enter URL that you would like to block. Click to enable the specific URL filter. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 28 Section 3 - Configuration Outbound Filter Outbound Filter enables you to control what packets are allowed to pass the router. Outbound filter applies on all outbound packets. OUTBOUND FILTER SETTING Outbound Filter:

Select this box to Enable the filter. Use Schedule Rule:

You may select Always On or choose the number of a schedule rule that you have defined. Copy to ID:

Copies the predefined filter to the specified ID OUTBOUND FILTER RULES LIST Identifies the filter. ID:

Source IP : Ports:

Destination IP : Ports:

Enable:

Specify the local IP address and then specify the port after the colon. Specify the remote IP address and then the port after the colon. Select this box to enable the filter. Schedule Rule #:

Specify the schedule rule number. Previous Page:

Go back to the previous filter page. Next Page:

Advance to the next filter page. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 29 Section 3 - Configuration Inbound Filter Inbound Filter enables you to control what packets are allowed to pass the router. Inbound filter only applies to packets that are destined for Virtual Servers or DMZ hosts. INTBOUND FILTER SETTING Inbound Filter:

Select this box to Enable the filter. Use Schedule Rule:

You may select Always On or choose the number of a schedule rule that you have defined. Copy to ID:

Copies the predefined filter to the specified ID INBOUND FILTER RULES LIST Identifies the filter. ID:

Source IP : Ports:

Destination IP : Ports:

Enable:

Specify the local IP address and then specify the port after the colon. Specify the remote IP address and then the port after the colon. Select this box to enable the filter. Schedule Rule #:

Specify the schedule rule number. Previous Page:

Go back to the previous filter page. Next Page:

Advance to the next filter page. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 30 Section 3 - Configuration SNMP SNMP (Simple Network Management Protocol) is a widely used network monitoring and control protocol that reports activity on each network device to the administrator of the network. SNMP can be used to monitor traffic and statistics of the DWR-113. The DWR-113 supports SNMP v1 or v2c. SNMP SNMP Local:

Select Enabled to allow local SNMP administration. Select Disabled to disallow local SNMP administration. SNMP Remote:

Get Community:

Set Community:

Select Enabled to allow local SNMP administration. Select Disabled to disallow local SNMP administration. Enter the password public in this field to allow Read only access to network administration using SNMP. You can view the network, but no configuration is possible with this setting. Enter the password private in this field to gain Read and Write access to the network using SNMP software. IP 1, IP 2, IP 3, IP 4:

Enter up to four IP addresses of any trap targets on your network. SNMP Version:

Select the SNMP version of your system. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 31 Section 3 - Configuration Routing The Routing page allows you to specify custom routes that determine how data is moved around your network. RIP SETTING RIP:

Select this box to enable routing. RIPv1: Protocol in which the IP address is routed through the internet. RIPv2: Enhanced version of RIPv1 with added features such as Authentication, Routing Domain, Next Hop Forwarding, and Subnet-

mask Exchange. ROUTING RULES ID:

Identifies the rule. Destination:

Subnet Mask:

Gateway:

Hop:

Enable:

Enter the IP of the specified network that you want to access using the static route. Enter the subnet mask to be used for the specified net work. Enter the gateway IP address to the specified network. Enter the amount of hops it will take to reach the specified network. Note: In a transmission path, each link is terminated at a network device such as a router or gateway. The number of hops equals the number of routers or gateways that data must pass through before reaching the destination. Select this box to enable the rule. D-Link DWR-113 User Manual 32 Section 3 - Configuration Advanced Wireless Advanced Wireless contains settings which can negatively affect the performance of your router if configured improperly. Do not change these settings unless you are already familiar with them or have been instructed to make the change by one of our support personnel. Beacon Interval:

Transmit Power:

RTS Threshold:

Fragmentation:

DTIM Interval:

WMM Capable:

TX Rates:

Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. Set the transmit power of the antennas. This value should remain at its default setting of 2347. If inconsistent data flow is a problem, only a minor modification should be made. The fragmentation threshold, which is specified in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting. A Delivery Traffic Indication Message (DTIM) is a countdown informing clients of the next window for listening to broadcast and multicast messages. The default interval is 3. WMM (Wi-Fi Multimedia) is QoS (Quality of Service) system for your wireless network. Enable this option to improve the quality of video and voice applications for your wireless clients. Select the basic transfer rates based on the speed of wireless adapters on your wireless network. It is strongly recommended to keep this setting to Auto. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 33 Section 3 - Configuration Advanced Network Advanced Network contains settings which can change the way the router handles certain types of traffic. We recommend that you do not change any of these settings unless you are already familiar with them or have been instructed to make the change by one of our support personnel. Enable UPnP:

Enable WAN Ping Respond:

UPnP Click Enable UPnP to use the Universal Plug and Play

(UPnP) feature. UPnP provides compatibility with networking e q u i p m e n t , s o f t w a r e a n d peripherals. WAN PING Select the box to allow the WAN port to be pinged. Blocking the Ping option may provide some extra security from hackers. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 34 Section 3 - Configuration Admin The Admin page allows you to change the Administrator password and enable Remote Management. The Admin has read/write access while the user has read-only access. Only the admin has the ability to change both admin and user account passwords. ADMINISTRATOR New Password:

Enter a password that the admin account will use to access the routers management interface. Confirm Password:

Confirm the chosen password. REMOTE MANAGEMENT Remote Management:

Remote management allows the DWR-113 to be configured from the Internet using a web browser. A username and password is still required to access the Web-

Management interface. Usually only a member of your network can browse the built-in web pages to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote (Internet) host. IP Allowed to Access:

Enter the Internet IP address of the PC that has access to the Broadband Router. If you enter an asterisk (*) in this field, then anyone will be able to access the Router. Adding an asterisk (*) into this field could present a security risk and is not recommended. This is the port number used to access the router. Example: 8080 is the port used for the Web-Management interface. Port:

Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 35 Section 3 - Configuration This section will help you set the time zone that you are in and the NTP (Network Time Protocol) Server. Daylight Saving can also be configured to adjust the time when needed. Time Time:

Displays the current time and date of the DWR-113. Time Zone:

Automatically synchronize with Internet time server:

NTP Server Used:

Sync. Result:

Select the appropriate Time Zone from the drop-down box. Select this checkbox to automatically synchronize the DWR-113 with an Internet time server. Choose the NTP Server used for synchronizing time and date. Shows the result of the last time synchronization. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 36 Section 3 - Configuration Syslog The DWR-113 keeps a running log of events and activities occurring on the router. You may send these logs to a SysLog server on your network. Enable Logging to Syslog Server:

Select this box to send the router logs to a Syslog Server. Syslog Server IP Address:

Enter the address of the Syslog server that will be used to send the logs. You may also select your computer from the drop-

down box (only if you want to receive an IP address from the router via DHCP). Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 37 Section 3 - Configuration E-mail Settings allows you to send the system log files, router alert messages, and firmware update notifications to an e-mail address. E-mail Settings Enable E-mail Notification:

SMTP Sever IP and Port:

When this option is enabled, router activity logs are e-mailed to a designated e-mail address. Enter the SMTP server IP address followed by a colon and the port number (e.g. 123.123.123.1:25). SMTP Username:

Enter the SMTP username. SMTP Password:

Send E-mail Alert to:

E-mail Subject:

Enter the SMTP password. Enter the e-mail address where you would like the e-mail sent to. Enter a subject for the e-mail. E-mail Log Now:

Click this button to access the e-mail log. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 38

Section 3 - Configuration Here, you can save the current system settings onto the local hard drive. System Save Settings To Local Hard Drive Load Settings From Local Hard Drive:

Restore To Factory Default Settings:

Use this option to save your current router configuration settings to a file and onto your computer. Click Save to open a file dialog, and then select a location and file name for the settings. Use this option to load the previously saved router configuration settings. Browse to find the saved file and then click Upload Settings to transfer those settings to the router. This option will restore all settings back to their defaults. Any settings that have not been backed up will be lost, including any rules that you have created. D-Link DWR-113 User Manual 39 Section 3 - Configuration Firmware Here, you can upgrade the firmware of your router. Make sure the firmware you want to use is on the local hard drive of the computer and then click Browse to upload the file. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site. Current Firmware Version:

Displays your current firmware version. Current Firmware Date:

Displays your current firmware date. Browse:

After you have downloaded the new firmware, click Browse to locate the firmware on your computer. Tick Accept unofficial firmware if you want to update the DWR-

113 with unofficial firmware (not recommended). Click Upload to start the firmware upgrade. D-Link DWR-113 User Manual 40 Section 3 - Configuration Dynamic DNS The DDNS feature allows you to host a server (Web, FTP, or Game Server) using a domain name that you have purchased (www. whateveryournameis.com) with your dynamically assigned IP address. Sign up for D-Links free DDNS service at www.dlinkddns.com. Enable DDNS:

Provider:

Host Name:

Dynamic Domain Name System is a method of keeping a domain name linked to a changing IP Address. Select this box to enable DDNS. Select your DDNS provider from the drop-down box. Enter the Host Name that you registered with your DDNS service provider. Username / E-mail:

Password / Key:

Enter the Username for your DDNS account. Enter the Password for your DDNS account. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 41 Section 3 - Configuration System Check This useful diagnostic utility can be used to check if a computer is connected to the network. It sends ping packets and listens for responses from the specific host. Host Name or IP Address:

Enter a host name or the IP address that you want to ping (Packet Internet Groper) and click Ping. PING Result:

The status of your Ping attempt will be displayed in the Ping Result box. D-Link DWR-113 User Manual 42 Section 3 - Configuration This section allows you to manage schedule rules for various firewall and parental control features. Schedules Enable Schedule:

Tick this check box to enable schedules. Add New Rule...:

Click this button to specify the start time, end time, and name of the rule. Edit:

Edit the rules start and end time. Delete:

Delete the rule. Name of Rule 1:

Start Time (hh:mm):

End Time (hh:mm):

Enter a name for your new schedule. Enter the time at which you would like the schedule to become active. Select the time at which you would like the schedule to become inactive. Click Save Settings to save your changes, or click Dont Save Settings to discard your changes. D-Link DWR-113 User Manual 43 Section 3 - Configuration All of your Internet and network connection details are displayed on this page. The firmware version is also displayed here. Device Information General:

WAN:

Displays the current time and firmware version. Displays the MAC address and the private (local) IP settings for the router. 3G Card:

Displays 3G card info, link status, and the network name. LAN:

Wireless LAN:

LAN Computers:

Displays the MAC address and the public IP settings for the router. Displays the wireless MAC address and your wireless settings such as SSID, Channel, and Encryption type. Displays the list of DHCP clients. D-Link DWR-113 User Manual 44 Section 3 - Configuration Logs Here, you can view logs and define events that you want to view. This router also has an internal syslog server, so you can send the log files to a computer that is running a syslog utility. D-Link DWR-113 User Manual 45 Section 3 - Configuration Statistics Here you can view the packets transmitted and received passing through your router on both WAN and LAN ports. The traffic counter will reset if the device is rebooted. D-Link DWR-113 User Manual 46 Section 3 - Configuration Wireless This table displays a list of wireless clients that are connected to your wireless router. It also displays the connection time and MAC address of the connected wireless clients. D-Link DWR-113 User Manual 47 Section 3 - Configuration Support D-Link DWR-113 User Manual 48 Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DWR-113 offers the following types of security:

WPA2 (Wi-Fi Protected Access 2) WPA (Wi-Fi Protected Access) WEP (Wired Equivalent Privacy) WPA2-PSK (Pre-Shared Key) WPA-PSK (Pre-Shared Key) What is WEP?

WEP stands for Wired Equivalent Privacy. It is based on the IEEE 802.11 standard and uses the RC4 encryption algorithm. WEP provides security by encrypting data over your wireless network so that it is protected as it is transmitted from one wireless device to another. To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When using WEP, you must determine the level of encryption. The type of encryption determines the key length. 128-bit encryption requires a longer key than 64-bit encryption. Keys are defined by entering in a string in HEX (hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code for Information Interchange alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember. The ASCII string is converted to HEX for use over the network. Four keys can be defined so that you can change keys easily. D-Link DWR-113 User Manual 49 Section 4 - Security Configure WEP It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Wireless Settings on the left side. 2. Next to Security Mode, select Enable WEP Security. 3. Next to Authentication, select Open or Shared Key. 4. Select either 64-bit or 128-bit encryption from the drop-down box next to WEP Encryption. 5. Next to Key Type, select either Hex or ASCII. Hex (recommended) - Letters A-F and numbers 0-9 are valid. ASCII - All numbers and letters are valid. 6. Next to Key 1, enter a WEP key that you create. Make sure you enter this key exactly on all your wireless devices. You may enter up to 4 different keys. 7. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the router. D-Link DWR-113 User Manual 50 Section 4 - Security What is WPA?

WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP:

Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys havent been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP. User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computers hardware-specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network. WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point. WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network. D-Link DWR-113 User Manual 51 Section 4 - Security Configure WPA-PSK It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Wireless Settings on the left side. 2. Next to Security Mode, select Enable WPA-Personal Security or Enable WPA2-Personal Security. 3. Next to Cipher Mode, select TKIP, AES, or Auto. 4. Next to PSK/EAP, select PSK. 5. Next to Passphrase, enter a key (passphrase). The key is an alpha-

numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. Make sure you enter this key exactly the same on all other wireless clients. 6. Enter the passphrase again next to Confirmed Passphrase. 7. Click Save Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WPA-PSK (or WPA2-PSK) on your adapter and enter the same passphrase as you did on the router. D-Link DWR-113 User Manual 52 Section 4 - Security Configure WPA (RADIUS) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on Wireless Settings on the left side. 2. Next to Security Mode, select Enable WPA-Personal Security or Enable WPA2-Personal Security. 3. Next to Cipher Mode, select TKIP, AES, or Auto. 4. Next to PSK/EAP, select EAP. 5. Next to RADIUS Server 1 enter the IP Address of your RADIUS server. 6. Next to Port, enter the port you are using with your RADIUS server. 1812 is the default port. 7. Next to Shared Secret, enter the security key. 8. If you have a secondary RADIUS server, enter its IP address, port, and secret key. 9. Click Apply Settings to save your settings. D-Link DWR-113 User Manual 53 Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows Vista Windows Vista users may use the built-in wireless utility. If you are using another companys utility or Windows 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a site survey option similar to the Windows Vista utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. or Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select Connect to a network. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button. If you get a good signal but cannot access the Internet, check the TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. D-Link DWR-113 User Manual 54 Section 5 - Connecting to a Wireless Network Configure Wireless Security It is recommended to enable wireless security (WEP/WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows Vista Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. D-Link DWR-113 User Manual 55 Section 5 - Connecting to a Wireless Network 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router. D-Link DWR-113 User Manual 56 Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows XP Windows XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another companys utility or Windows 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a site survey option similar to the Windows XP utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. or Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View Available Wireless Networks. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button. If you get a good signal but cannot access the Internet, check the TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. D-Link DWR-113 User Manual 57 Section 5 - Connecting to a Wireless Network Configure WEP It is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used. 1. O p e n t h e W i n d o w s X P W i r e l e s s U t i l i t y b y r i g h t -

clicking on the wireless computer icon in your system tray

(lower-right corner of screen). Select View Available Wireless Networks. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. D-Link DWR-113 User Manual 58 Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the same WEP key that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WEP settings are correct. The WEP key must be exactly the same as on the wireless router. D-Link DWR-113 User Manual 59 Section 5 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used. 1. Open the Windows XP Wireless Utility by right-clicking on the wireless computer icon in your system tray

(lower-right corner of screen). Select View Available Wireless Networks. 2. Highlight the wireless network (SSID) you would like to connect to and click Connect. D-Link DWR-113 User Manual 60 Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router. D-Link DWR-113 User Manual 61 Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DWR-113. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1. Why cant I access the web-based configuration utility?

When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. Make sure you have an updated Java-enabled web browser. We recommend the following:

Internet Explorer 6.0 or higher Netscape 8 or higher Mozilla 1.7.12 (5.0) or higher Opera 8.5 or higher Safari 1.2 or higher (with Java 1.3.1 or higher) Camino 0.8.4 or higher Firefox 1.5 or higher Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on. Disable any internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and Windows XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it. D-Link DWR-113 User Manual 62 Section 6 - Troubleshooting Configure your Internet settings:

Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times. Close your web browser (if open) and open it. Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your the web management. If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer. 2. What can I do if I forgot my password?

If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults. To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty. D-Link DWR-113 User Manual 63 Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers. A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link. D-Link DWR-113 User Manual 64 Appendix A - Wireless Basics What is Wireless?

Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless?

D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network. How does wireless work?

Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN). Wireless Local Area Network (WLAN) In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues. Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. D-Link DWR-113 User Manual 65 Appendix A - Wireless Basics Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesnt use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries. Who uses wireless?

Wireless technology as become so popular in recent years that almost everyone is using it, whether its for home, office, business, D-Link has a wireless solution for it. Home Gives everyone at home broadband access Surf the web, check e-mail, instant message, and etc Gets rid of the cables around the house Simple and easy to use Small Office and Home Office Stay on top of everything at home as you would at office Remotely access your office network from home Share Internet connection and printer with multiple computers No need to dedicate office space D-Link DWR-113 User Manual 66 Appendix A - Wireless Basics Where is wireless used?

Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and its becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called hotspots. Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers. Wireless network is easy to setup, but if youre installing it for the first time it could be quite a task not knowing where to start. Thats why weve put together a few setup steps and tips to help you through the process of setting up a wireless network. Tips Here are a few things to keep in mind, when you install a wireless network. Centralize your Router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/

access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range. Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency. Security Dont let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up. D-Link DWR-113 User Manual 67 Appendix A - Wireless Basics Wireless Modes There are basically two modes of networking:

Infrastructure All wireless clients will connect to an access point or wireless router. Ad-Hoc Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more WNA-2330 wireless network Cardbus adapters. An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate. D-Link DWR-113 User Manual 68 Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows Vista users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters. D-Link DWR-113 User Manual 69 Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:

Step 1 Windows Vista -

Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Windows XP -

Click on Start > Control Panel > Network Connections. Windows 2000 -

From the desktop, right-click My Network Places > Properties. Step 2 Right-click on the Local Area Connection which represents your network adapter and select Properties. Step 3 Highlight Internet Protocol (TCP/IP) and click Properties. Step 4 Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the routers LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step 5 Click OK twice to save your settings. D-Link DWR-113 User Manual 70 Appendix C - Technical Specifications Technical Specifications Data Rates **

1/2/5.5/11 Mbps in 802.11b mode 6/9/11/12/18/24/36/48/54 Mbps in 802.11g mode Up to 150 Mbps in 802.11n mode Standards IEEE 802.11b IEEE 802.11g IEEE 802.3 IEEE 802.3u 150N Frequency 2.4 - 2.4835 GHz Wireless Security 64/128-bit WEP (Wired Equivalent Privacy) WPA & WPA2 (Wi-Fi Protected Access) Firewall IP Filtering Network Address Translation (NAT) MAC Filtering VPN L2TP/PPTP/IPSEC VPN Pass-through Antenna 1 External Wi-Fi antenna Ports 4 x LAN (RJ-45) 1x WAN 1 x USB LED Status Indicators 3G WAN Wi-Fi LAN 1, LAN 2, LAN 3, LAN 4 Power External 5 V DC 2 A power adapter Dimensions (L x W x H) 148 x 128 x 23 mm (5.8 x 5.0 x 0.9 inches) Operating Temperature 0 to 40 C (32 to 104 F) Operating Humidity 10% to 95% (Non-condensing) D-Link DWR-113 User Manual 71 Appendix C - Technical Specifications Certifications FCC CE NCC

* Supported frequency band is dependent upon regional hardware version.

** Maximum wireless signal rate derived from IEEE Standard 802.11g specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range. D-Link DWR-113 User Manual 72

FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

Photographs of EUT 3. Internal Photograph of EUT Report No.: EP0O0724-01 Brand Name: D-Link / Model Name: DWR-113 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 7 of 10 Report Issued Date

: Jan. 25, 2011 Report Version

: Rev. 02 Photographs of EUT Report No.: EP0O0724-01 Brand Name: D-Link / Model Name: DWR-113 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 8 of 10 Report Issued Date

: Jan. 25, 2011 Report Version

: Rev. 02 Photographs of EUT Report No.: EP0O0724-01 WLAN Antenna Brand Name: D-Link / Model Name: DWR-113 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 9 of 10 Report Issued Date

: Jan. 25, 2011 Report Version

: Rev. 02 Photographs of EUT Report No.: EP0O0724-01 WLAN Antenna Brand Name: D-Link / Model Name: DWR-113 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 10 of 10 Report Issued Date

: Jan. 25, 2011 Report Version

: Rev. 02

1. Photographs of EUT External Photograph of EUT Report No.: EP0O0724-01 Brand Name: D-Link / Model Name: DWR-113 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 1 of 10 Report Issued Date

: Feb. 16, 2011 Report Version

: Rev. 03 Photographs of EUT Report No.: EP0O0724-01 Brand Name: D-Link / Model Name: DWR-113 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 2 of 10 Report Issued Date

: Feb. 16, 2011 Report Version

: Rev. 03 2. Photographs of EUT Photograph of Accessory Report No.: EP0O0724-01 Brand Name: D-Link / Model Name: DWR-113 List of Accessory:

AC Adapter Brand Name Model Name D-Link AMS3-0502000FU Specification of Accessory Remark: For accessories equipped with this EUT, please refer to the following photos. SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 3 of 10 Report Issued Date

: Feb. 16, 2011 Report Version

: Rev. 03 Photographs of EUT Report No.: EP0O0724-01 Brand Name: D-Link / Model Name: DWR-113 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 4 of 10 Report Issued Date

: Feb. 16, 2011 Report Version

: Rev. 03 Photographs of EUT Report No.: EP0O0724-01 Brand Name: D-Link / Model Name: DWR-113 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 5 of 10 Report Issued Date

: Feb. 16, 2011 Report Version

: Rev. 03 Photographs of EUT Report No.: EP0O0724-01 Brand Name: D-Link / Model Name: DWR-113 SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 FCC ID : KA2WR113A1 Page Number

: 6 of 10 Report Issued Date

: Feb. 16, 2011 Report Version

: Rev. 03

93mm ry @

D-Lin Model: DWR-113 FCC ID: KA2WR113A1 This device complies with part 15 of the FCC Rules. Operation is subjectto the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that may cause undesired operation E FECE MADE IN CHINA 32mm

Label Location FCC ID: KA2WR113A1 Bottom of the device Label Location

oe

D-Link No.289, Sinhu 3rd Rd., Neihu District, Taipei City 114, Taiwan, R.O.C September 28, 2008 Power of Attorney To whom it may concern

|, the undersigned, Michael Boschma, hereby authorize the persons listed below to act in behalf of me to sign all related documents for D-Links FCC application. Wireless Shinglin Chung/Senior manager Broad Band Jacob Luo/Senior Director

+886-2-66000123#5819 +886-2-66000123#6810 shinglin_chung@alink.com.tw jacob_luo@dlink.com.tw Digital home Robert Lin/Senior Director Switch & Henghsin Liao/Associate Vice President

+886-2-66000123#5720 security product +886-2-66000123#5810 robert_lin@dlink.com.tw henghsin_liao@dlink.com.tw Company Name: D-Link Co. Ltd Fax: 886-2-55509988 Company Address: No.289,Sinhu 3" Rd.,Neihu District, Taipei City 114, Taiwan, R.O.C. Authorization period: Jan 1*', 2008 ~Dec 31%, 2058 Should you have any question regarding this power of attorney, please don't hesitate to contact me Sincerely, Much ash Peachrna 9-28-08 Michael Boschma D-Link Co. TEL: (714) 885-6000 FAX: (949) 272-4629 E-mail:Mboschma@dlink.com

MY UWOO YUTpOSunyo Surpurys :rewu-q 88660SSS-C-988 *XVA OI8S IXA 7100997-C-988 * TAL uonesodiog yury q :Auedwod sunyy SulpUrys :uosaag 39}U0D smo Aya1aouIS uoruaye jsaq AW aavy aseord rayeUr sty) BuTpsedar s}UsUTUOD Jo suoNsanb Aue aavy nod pnoys Apooup Qu [eUOKYUIAJUT UOJI0dg 0} 11 puas osveld asuodse1 pur yuaWIAspsymouyse Aue savy NOK J]

TVEIlLaM evel (GI O04

:BULMOT]OJ sv Jo INpoAd 9Y} 0} postu] SI VOHLZLAOYINE sty,

@)SE8 O'S IT 8661 JO dV ESNgY BnIG-nuY O41 Jo [OES UONas 0} Juensind sy1youaq DOJ opnyout yey} syJouaq [eJopa,j 0} [etuap v 0} yoalqns st (q) ZOOT TI UO MAO Lp Ul pourap se uoneotydde s1y} 0} Aped Aue iow queordde ay} Joyjiou yey} sarpTieo JoyINy OM, Jyeyoq UMO IMO UO sjoR se ALOYINe [ea] ours oy} savy [TeYs AWOyNE yeuorjeu ay} YIM pepssu uoTeOTUNUIWOD Aue pue [eAoidde DD oy) ut pasmbar sassaooid [ye 0} BuNejer Jo sIoyew oy) Uo dUT [eUOLeUIEUT WoyAOdg UI NA AOY Aq yno porto syoe [Je pue AUy UOT}EIUSUUNSOP Joyo puL | / WIOJ ay} UBIs 0} pue yoofoid sty) 10} o[qIsuodsor Buraq uosiad ay} sv UT [VUOHEUADUT UOVOdS UI NY AOY poleusisop oavy Sunyy suyuryg ] eq) parynou oq asvolg uloouos Aer yt Woy OL A9U.10}7V JO 19M0g 1102 ZI Azenuer :oreq 679b-TLT-6H6 XB SOL9-S88-PIL AL saves POUL) BOLZ BTU TED AajjeA wreywmno,y UULULIOH I] S6SLT uone.10d107> yuUrT Gq

D Link Corporation 17595 Mt. Herrmann, Fountain Valley, California 92708, United States Tel: 714-885-6105 ; Fax: 949-272-4629 Date: March 3, 2011 We, D Link Corporation, declare that this EUT (FCC ID: KA2WR113A1) doesn't have Ad Hoc Mode function on "non-US/Canada frequencies". In addition, the frequency selection feature is disabled by firmware for devices marketed to the US/Canada. For DTS part of this device, only channels 1~11 will be used in North America. Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, ep Contact Person: Shinling Chung Company: D Link Corporation TEL: 886-2-26600123, Ext. 5810 FAX: 886-2-55509988 E-mail: shinling_chung@dlink.com.tw

D Link Corporation 17595 Mt. Herrmann, Fountain Valley, California 92708, United States Tel: 714-885-6105 ; Fax: 949-272-4629 Date: January 12, 2011 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: KA2WR113A1 To Whom It May Concern:

We, D Link Corporation, hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite filing. Sincerely yours, po Shinling Chung

D Link Corporation 17595 Mt. Herrmann, Fountain Valley, California 92708, United States Tel: 714-885-6105 ; Fax: 949-272-4629 Date: January 12, 2011 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: KA2WR113A1 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Schematics (file: DWR-113_Schem_Confidential.pdf) Block Diagram (file: DWR-113_BlkDia_Confidential.pdf) Parts List (file: DWR-113_PartsLst_Confidential.pdf) Operation Description (file: DWR-113_OpDes_Confidential.pdf) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, OQ Shinling Chung Rey. 1/1/03

D Link Corporation 17595 Mt. Herrmann, Fountain Valley, California 92708, United States Tel: 714-885-6105 ; Fax: 949-272-4629 Date: January 12, 2011 Federal Communications Commission Authorization and Evaluation Division RE : Certification Application FCCID :KA2WRII3A1 To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days:

External Photos (file: DWR-113_ExtPho.pdf) Internal Photos (file: DWR-113_IntPho.pdf) Test Setup Photos (file: DWR-113_Tsup.pdf) User Manual (file: DWR-113_UserMan.pdf) ooo The application contains technical information, which D Link Corporation deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, O.. Shinling Chung W/L