Datalogic S.r.l. Via S. Vitalino, 13 40012 Lippo di Calderara di Reno Bologna - Italy Telephone: (+39) 051-3147011 Fax: (+39) 051-3147205 2016 Datalogic S.r.l. An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic S.r.l. or its subsidiaries or affiliates. Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation. Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website (www.datalogic.com) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page. Disclaimer Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. DL-Axist and the DL-Axist logo are trademarks of Datalogic S.r.l. All other brand and product names may be trademarks of their respective owners. See www.patents.datalogic.com for patent list. Patents This product is covered by one or more of the following patents:
Design patents: EP002730135, US7273179, US7537166 Utility patents: EP0789315B1, EP0996284B1, EP0999514B1, EP1114390B1, EP1128315B1, EP1172756B1, EP1396811B1, EP1413971B1, EP1804089B1, EP1828957B1, EP2275966B1, EP2315156B1, EP2517148B1, EP2649555B1, JP4435343B2, JP5192390B2, US5992740, US6478224, US6512218, US6513714, US6561427, US6808114, US6877664, US6997385, US7053954, US7234641, US7387246, US7721966, US8113430, US8561906, US8888003, US8915443, ZL200680050007.8. Read carefully the DL-Axist user manual (available at www.datalogic.com) before performing any type of connection to the DL-Axist PDA. The user is responsible for any damage caused by incorrect use of the equipment or by inobservance of the indication supplied in the user manual. NOTE General Safety Rules Personal Digital Assistant (PDA) WWAN Version CAUTION Before using the device and the battery packs, read this Addendum carefully. Use only the components and accessories supplied by the manufacturer for the specific DL-Axist being used. Do not attempt to disassemble the DL-Axist PDA, as it does not contain parts that can be repaired by the user. Any tampering will invalidate the warranty. When replacing the battery pack or at the end of the operative life of the DL-
Axist PDA, disposal must be performed in compliance with the laws in force in your jurisdiction. Do not submerge the DL-Axist in liquid products. For further information or support, refer to the Datalogic web site: www.data-
logic.com. Power Supply This device is intended to be connected to a UL Listed/CSA Certified computer which supplies power directly to the DL-Axist or else be supplied by a UL Listed/CSA Certified Power Unit marked Class 2 or LPS power source rated 5 V, 2.0 A, which supplies power directly to the DL-Axist via the power connector of the cable. The adapter package includes three international plug adapters. The adapters must be plugged in the power supply before the power supply itself is plugged on the wall outlet. Battery Information DL-Axist battery pack is not initially fully charged. After installing the battery, charge it with the USB cable or with the single dock. By default, the battery pack is disconnected at the factory to avoid damage due to excessive draining. Annual replacement of rechargeable battery pack avoids possible risks or abnormalities and ensures maximum performance. Avoid storing batteries for long periods in a state of full charge or very low charge. We recommend charging the battery pack every two to three months to keep its charge at a moderate level to maximize battery life. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Il y a risque dexplosion si la batterie est remplace par une batterie de type incorrect. Mettre au rebut les batteris usages confor mment aux instructions. Even if the storage temperature range is wider, in order to achieve the longest battery life, store the terminal and the spare batteries between 20 to 30C (68 to 86F). Charging is allowed in the battery temperature range from 0C to 45C. To maximize operating autonomy, the DL-Axist checks its battery level at all times. If the battery is not sufficiently charged, the DL-Axist will not turn on when the ON/OFF Power button is pressed. In this case, either substitute with a charged battery, insert the DL-Axist into a powered cradle, or plug it into a wall charger. To maximize battery life, turn off radios when they are not needed. CAUTION WARNING NOTE Battery Safety Guidelines Safety & Regulatory Addendum 852000970 (Rev. A) Dec. 2016 This document is an addendum to the Quick Start Guide
(QSG) for this product. See the QSG for additional product information. WARNING 2016 Datalogic S.r.l. All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. DL-Axist and the DL-Axist logo are trademarks of Datalogic S.r.l. All other brand and product names may be trademarks of their respective owners. www.datalogic.com Installing, charging and/or any other action should be done by authorized personnel and following this manual. The battery pack may get hot, explode, ignite, and/or cause serious injury if exposed to abusive conditions. If the battery pack is replaced with an improper type, there is risk of explosion and/or fire. Use the battery box to carry the battery pack, do not put the battery pack in your pocket. Do not place the battery pack in or near a fire or other heat source; do not place the battery pack in direct sunlight, or use or store the battery pack inside unventilated areas in hot weather; do not place the battery pack in microwave ovens, in clothes dryers, in high pressure containers, on induction cook surfaces or similar devices. Doing so may cause the battery pack to generate heat, explode or ignite. Using the battery pack in this manner may also result in a loss of performance and a shortened life expectancy. Use only a Datalogic approved power supply. The use of an alternative power supply will void the product warranty, may cause product damage and may cause heat, an explosion, or fire. The area in which the units are charged should be clear of debris and combustible materials or chemicals. Do not use the battery pack of this terminal to power devices other than this terminal. Immediately discontinue use of the battery pack if, while using, charging or storing the battery pack, the battery pack emits an unusual smell, feels hot, changes color or shape, or appears abnormal in any other way. Do not short-circuit the battery pack contacts connecting the positive terminal and negative terminal. This might happen, for example, when you carry a spare battery pack in your pocket or purse; accidental shortcircuiting can occur when a metallic object such as a coin, clip, or pen causes direct connection of the contacts of the battery pack (these look like metal strips on the battery pack). Shortcircuiting the terminals may damage the battery pack or the connecting object. Do not apply voltages to the battery pack contacts. Do not pierce the battery pack with nails, strike it with a hammer, step on it or otherwise subject it to strong impacts, pressures, or shocks. Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The battery pack contains safety and protection devices, which, if damaged, may cause the battery pack to generate heat, explode or ignite. In case of leakage of liquid from the battery, avoid contact with liquid the skin or eyes. If the contact occurs, immediately wash the affected area with water and consult a doctor. Do not solder directly onto the battery pack. Do not expose the battery pack to liquids. Avoid any knocks or excessive vibrations. If the device or the battery is dropped, especially on a hard surface, you should take it to the nearest Authorised Repair Centre for inspection before continuing to use it. Before replacing the battery pack, turn off the device or put it in swap battery mode (refer to the DL-Axist User's Manual). Do not remove or damage the battery packs label. Do not use the battery pack if it is damaged in any part. Battery pack usage by children should be supervised. Collect and recycle waste batteries separately from the device in compliance with European Directive 2006/66/EC, 2011/65, 2002/96/EC and subsequent modifications, with US and China regulatory laws and regulations about the environment. CTIA Statements a. b. Do not disassemble or open crush, bend or deform, puncture or shred Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, expose to fire, explosion or other hazard. Only use the battery for the system for which it is specified Only use the battery with a charging system that has been qualified with the system per CTIA Certification Requirements for Battery System Compliance to IEEE 1725. Use of an unqualified battery or charger may present a risk of fire, explosion, leakage, or other hazard. Do not short circuit a battery or allow metallic conductive objects to contact battery terminals. Replace the battery only with another battery that has been qualified with the system per this standard, IEEE-Std-1725. Use of an unqualified battery may present a risk of fire, explosion, leakage or other hazard. Only authorized service providers shall replace battery. (If the battery is non-
user replaceable). Promptly dispose of used batteries in accordance with local regulations Battery usage by children should be supervised. Avoid dropping the phone or battery. If the phone or battery is dropped, especially on a hard surface, and the user suspects damage, take it to a service center for inspection. Improper battery use may result in a fire, explosion or other hazard. The device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program. The device shall only be connected to CTIA certified adapters. c. d. e. f. g. h. i. j. k. l. m. Wireless and Radio Frequencies Warnings WARNING recommendations provided by Health their pacemaker and/or any other medical device;
Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals generated by the DL-Axist. Datalogic recommends persons with pacemakers or other medical devices to follow the same Industry Manufacturers Associations for mobile phones. Persons with pacemakers:
Should ALWAYS keep this device more than twenty five (25) cm from Should not carry this device in a breast pocket;
Should keep the device at the opposite side of the pacemaker and/or any other medical device;
Should turn this device OFF or move it immediately AWAY if there is any reason to suspect that interference is taking place. Should ALWAYS read pacemaker or any other medical device guides or should consult the manufacturer of the medical device to determine if it is adequately shielded from external RF energy. In case of doubt concerning the use of wireless devices with an implanted medical device, contact your doctor. Turn this device OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may use equipment that could be sensitive to external RF energy. RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. An air bag inflates with great force. DO NOT place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If a vehicles wireless equipment is improperly installed and the air bag inflates, serious injury could result. Turn off the device when in any area with a potentially explosive atmosphere. Observe restrictions and follow closely any laws, regulations, warnings and best practices on the use of radio equipment near fuel storage areas or fuel distribution areas, chemical plants or where any operation involves use of explosive materials. Do not store or carry flammable liquids, explosive gases or materials with the device or its parts or accessories. Areas with a potentially explosive atmosphere are often, but not always, clearly marked or shown. Sparks in such areas could cause an explosion or fire, resulting in injury or even death. Canadian Statement Ne pas regarder le faisceu. Attention classe 2 lumire laser en cas douverture eviter lesposition - lumire est mise de la ouverture. Ce produit est conform au sous-chapitre J de CFR 21. Pour le modle avec TYPE qui contient deux lettres WI. Rayonnement laser ne pas regarder dans le faisceu ne par regarder avec strumentation optique - appareil laser de classe 2 emission maximale de 1mw longueur donde emise 630 - 650nm selon EN 60825-1:2007. Pour le modle avec TYPE qui contient deux lettres HL. Rayonnement laser ne pas regarder dans le faisceu appareil laser de classe 2 mission maximale de 1mw longueur donde mise 630 - 650nm 15 ms poulse selon IEC 60825-1:2007. FCC Compliance FCC Interference Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation. This equipment gener-
ates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunc-
tion with any other antenna or transmitter. IMPORTANT NOTE:
FCC Radiation Exposure Statement This model device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on the below:
- FCC ID: U4GDLNFCUR1 This device is compliant with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528-2013 and published RF exposure KDB. For body worn operation, this device has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and the positions the handset a minimum of 10 mm from the body. Use of other enhancements may not ensure compliance with FCC RF exposure guidelines. If you do not use a body-worn accessory and are not holding the device at the ear, position the handset a minimum of 10 mm from your body when the device is switched on. Industry Canada Compliance IC Statement:
This device complies with RSS-247; of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de classe B est conforme la norme NMB-003. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence.L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage adiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and.
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.
(iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:
Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment:
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer la limite de p.i.r.e.;
(iii) le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas.
(iv) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 1.5 cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC RF Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 1.5 cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 10 mm de distance entre la source de rayonnement et votre corps. SAR Compliance This product has been tested and found to comply with the following standards:
IEEE1528-2013: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. RSS102 Issue 5: Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands). FCC SAR values:
Head: 0.385w/kg@1g Body -Worn: 0.678W/kg@1g Hotspot: 1.192 W/Kg@1g Body-worn Operation This device was tested for typical body-worn operations. A minimum separation distance must be maintained between the user's body and the handset, including the antenna:
10 mm to comply with the RF exposure requirements in Europe Third-party belt-clips, holsters and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Laser Safety The following information applies to both laser models and the DL-Axist Imager Aiming System. The laser light is visible to the human eye and is emitted from the window indicated in the figure below. LASER LIGHT - DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT MAX OUTPUT RADIATION 1 mW COMPLIANT WITH EN 60825-1 (2007) Scan Window WI1 HL2 Model N Label3 WI1 HL2 FCC ID Label3 S/N & IMEI Label3 1. 2. 3. For models with Type containing WI. For models with Type containing HL. The label artworks may be only a draft. Refer to the product labels for more precise information. NOTE: do not remove the labels ITALIANO DEUTSCH FRANAIS ESPAOL LA LUCE LASER VISIBILE ALL'OCCHIO UMANO E VIENE EMESSA DALLA FINESTRA INDICATA NELLA FIGURA. DIE LASER-STRAHLUNG IST FR DAS MENSCHLICHE AUGE SICHTBAR UND WIRD AM STRAHLAUS TRITTSFENSTER AUSGESENDET (SIEHE BILD). LE RAYON LASER EST VISIBLE L'OEIL NU ET IL A LUZ LSER ES VISIBLE AL OJO HUMANO Y ES EST MIS PAR LA FENTRE DSIGNE SUR L'ILLUSTRATION DANS LA EMITIDA POR LA VENTANA INDICADA EN LA FIGURA. FIGURE. LUCE LASER NON FISSARE IL FASCIO LASERSTRAHLUNG NICHT IN DEN STRAHL BLICKEN APPARECCHIO LASER DI CLASSE 2 MASSIMA POTENZA D'USCITA: 1 mW LUNGHEZZA D'ONDA EMESSA:
(2007). PRODUKT DER LASERKLASSE 2 MAXIMALE mW ENTSPR. EN 60825-1
(2007). RAYON LASER EVITER DE REGARDER LE RAYON APPAREIL LASER DE CLASSE 2 PUISSANCE DE RAYO LSER NO MIRAR FIJO EL RAYO APARATO LSER DE CLASE 2 MXIMA POTENCIA DE SORTIE: 1 mW SALIDA: 1 mW LONGITUD DE ONDA EMISE:
(2007). EMITIDA:
(2007). CONFORME A EN 60825-1 WELLENLGE:
CONFORME A EN 60825-1 CONFORME A EN 60825-1 AUSGANGSLEISTUNG: 1 LONGUEUR D'ONDE ENGLISH The following information is provided to comply with the rules imposed by international authorities and refers to the correct use of your mobile computer. STANDARD LASER SAFETY REGULATIONS This product conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN 60825-1 at the date of manufacture. For installation, use and maintenance, it is not necessary to open the device. Do not attempt to open or otherwise service any components in the optics cavity. Opening or servicing any part of the optics cavity by unauthorized personnel may violate laser safety regulations. The optics system is a factory only repair item. Use of controls or adjustments or performance of procedures other than those specified herein may result in exposure to hazardous visible laser light. Use of optical systems with the scanner will increase eye hazard. Optical instruments include binoculars, microscopes, eye glasses and magnifying glasses. WARNING The product utilizes a low-power laser diode. Although staring directly at the laser beam momentarily causes no known biological damage, avoid staring at the beam as one would with any very strong light source, such as the sun. Avoid that the laser beam hits the eye of an observer, even through reflective surfaces such as mirrors, etc. ITALIANO Le seguenti informazioni vengono fornite dietro direttive delle autorit internazionali e si riferiscono alluso corretto del terminale. NORMATIVE STANDARD PER LA SICUREZZA LASER Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data di produzione: CDRH 21 CFR 1040 e EN 60825-1. Non si rende mai necessario aprire lapparecchio per motivi di installazione, utilizzo o manutenzione. ATTENZIONE Non tentare di accedere allo scomparto contenete i componenti ottici o di farne la manutenzione. Lapertura dello scomparto, o la manutenzione di qualsiasi parte ottica da parte di personale non autorizzato, potrebbe violare le norme della sicurezza. Il sistema ottico pu essere riparato solamente alla fabbrica. L'utilizzo di procedure o regolazioni differenti da quelle descritte nella documentazione pu provocare un'esposizione pericolosa a luce laser visibile. Luso di strumenti ottici assieme allo scanner pu aumentare il pericolo di danno agli occhi. Tali strumenti ottici includono cannocchiali, microscopi, occhiali e lenti di ingrandimento. ATTENZIONE Non tentare di accedere allo scomparto contenete i componenti ottici o di farne la manutenzione. Lapertura dello scomparto, o la manutenzione di qualsiasi parte ottica da parte di personale non autorizzato, potrebbe violare le norme della sicurezza. Il sistema ottico pu essere riparato solamente alla fabbrica. L'utilizzo di procedure o regolazioni differenti da quelle descritte nella documentazione pu provocare un'esposizione pericolosa a luce laser visibile. Luso di strumenti ottici assieme allo scanner pu aumentare il pericolo di danno agli occhi. Tali strumenti ottici includono cannocchiali, microscopi, occhiali e lenti di ingrandimento. Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti danni riportati dallocchio umano in seguito ad una esposizione di breve durata, evitare di fissare il raggio laser cos come si eviterebbe qualsiasi altra sorgente di luminosit intensa, ad esempio il sole. Evitare inoltre di dirigere il raggio laser negli occhi di un osservatore, anche attraverso superfici riflettenti come gli specchi. DEUTSCH Die folgenden Informationen stimmen mit den Sicherheitshinweisen berein, die von internationalen Behrden auferlegt wurden, und sie beziehen sich auf den korrekten Gebrauch vom Terminal. NORM FR DIE LASERSICHERHEIT Dies Produkt entspricht am Tag der Herstellung den gltigen EN 60825-1 und CDRH 21 CFR 1040 Normen fr die Lasersicherheit. Es ist nicht notwendig, das Gert wegen Betrieb oder Installations- und Wartungs-Arbeiten zu ffnen. Unter keinen Umstnden darf versucht werden, die Komponenten im Optikhohlraum zu ffnen oder auf irgendwelche andere Weise zu warten. Das ffnen bzw. Warten der Komponenten im Optikhohlraum durch unbefugtes Personal verstt gegen die Laser-
Sicherheitsbestimmungen. Das Optiksystem darf nur werkseitig repariert werden. Jegliche nderungen am Gert sowie Vorgehensweisen, die nicht in dieser Betriebsanleitung beschrieben werden, knnen ein gefhrliches Laserlicht verursachen. Die Verwendung von Optiksystemen mit diesem Scanner erhht die Gefahr einer Augenbeschdigung. Zu optischen Instrumenten gehren unter anderem Fernglser, Mikroskope, Brillen und Vergrerungsglser. ACHTUNG Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschden von kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden fr lngere Zeit in den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die Sonne). Vermeiden Sie es, den Laserstrahl weder gegen die Augen eines Beobachters, noch gegen reflektierende Oberflchen zu richten. FRANAIS Les informations suivantes sont fournies selon les rgles fixes par les autorits internationales et se rfrent une correcte utilisation du terminal. NORMES DE SECURITE LASER Ce produit est conforme aux normes de scurit laser en vigueur sa date de fabrication:
CDRH 21 CFR 1040 et EN 60825-1. Il nest pas ncessaire douvrir lappareil pour linstallation, lutilisation ou lentretien. LNe pas essayer douvrir ou de rparer les composants de la cavit optique. Louverture de la cavit optique ou la rparation de ses composants par une personne non qualifie peut entraner le nonrespect des rgles de scurit relatives au laser. Le systme optique ne peut tre rpar quen usine. L'utilisation de procdures ou rglages diffrents de ceux donns ici peut entraner une dangereuse exposition lumire laser visible. Lutilisation dinstruments optiques avec le scanneur augmente le danger pour les yeux. Les instruments optiques comprennent les jumelles, les microscopes, les lunettes et les verres grossissants. ATTENTION Le produit utilise une diode laser. Aucun dommage aux yeux humains na t constat la suite dune exposition au rayon laser. Eviter de regarder fixement le rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter aussi de diriger le rayon vers les yeux dun observateur, mme travers des surfaces rflchissantes (miroirs, par exemple). ESPAOL Las informaciones siguientes son presentadas en conformidad con las disposiciones de las autoridades internacionales y se refieren al uso correcto del terminal. NORMATIVAS ESTNDAR PARA LA SEGURIDAD LSER Este aparato resulta conforme a las normativas vigentes de seguridad lser a la fecha de produccin: CDRH 21 CFR 1040 y EN 60825-1. No es necesario abrir el aparato para la instalacin, la utilizacin o la manutencin. No intente abrir o de ninguna manera dar servicio a ninguno de los componentes del receptculo ptico. Abrir o dar servicio a las piezas del receptculo ptico por parte del personal no autorizado podra ser una violacin a los reglamentos de seguridad. El sistema ptico se puede reparar en la fbrica solamente. La utilizacin de procedimientos o regulaciones diferentes de aquellas describidas en la documentacin puede causar una exposicin peligrosa a la luz lser visible. El uso de sistemas pticos con el escner aumentar el riesgo de daos oculares. Los instrumentos pticos incluyen binoculares, microscopios, lentes y lupas. ATENCIN El aparato utiliza un diodo lser a baja potencia. No son notorios daos a los ojos humanos a consecuencia de una exposicin de corta duracin. Eviten de mirar fijo el rayo lser as como evitaran cualquiera otra fuente de luminosidad intensa, por ejemplo el sol. Adems, eviten de dirigir el rayo lser hacia los ojos de un observador, tambin a travs de superficies reflectantes como los espejos. LED Class LED illuminator integrated in the DL-Axist models are compliant with exempt risk group requirements according to IEC62471:2006 and EN 62471:2008. Audio Safety To prevent possible hearing damage, do not listen at high volume levels for long periods.