DNWAP62 WiFi Access Point Users Manual-QSG-AP62

Additional Resources Dattos Partner Portal (partners.datto.com) is the place to go for everything Datto. The Partner Portal includes:

Datto Knowledge Base (kb.datto.com) - technical articles to help you with all of your Datto Networking needs MarketNow (datto.com/marketnow) - your very own Marketing Automation Platform Sales Resources - Sales Playbooks, MSPeasy eBooks and videos, etc. Your dedicated Channel Account Manager can help with sales and planning questions along the way. If you need additional help, the Datto Support Team is here for you 24/7/365. Contact Us support@datto.com North America: +1.877.455.6015 EMEA: +44.(0).118.402.9609 Australia/New Zealand: +61 (02) 8015 6826 For more information, visit www.datto.com/networking 2017 Datto Inc. All rights reserved. Unmounting Directions Ethernet or Junction Box Mount Outdoor Mount To unlock, insert a small, flat screwdriver into the Mount Release Hole on the side of the access point. Slide the access point upwards until it disengages from the mounting plate. This access point can be mounted to any junction box for secure installations in hotel and resort guest rooms, dorms, care facilities and more. 1) Remove rear door and seal. 2) Mount flat side of plate to junction box. This access point can be configured as an outdoor model and mounted to any wall or pole. This configuration protects against the sun, rain and dust. Operating temperatures for this access point range from 0C to 50C. 1) Remove rear door and seal. Peel plastic tab off from door. 2) Secure flat side of mount to outdoor fixture. Arrows on plate pointing upwards. 3) Connect included slim ethernet cable from device

(Port 1) to connection in wall. 4) Slide device down plate to lock in place. 3) Place ethernet cable through seal and connect to device (Port 1). Reinstall seal and back cover. 4) Slide device down plate to lock in place. AP62 Quick Start Guide Cloud Management Whats in the Box Physical Installation 1. Sign in to networking.datto.com. Click Add New button.

(1) Access Point 2. Create a new network by navigating to All Networks > Create Network, or select an existing network on the All Networks page. 3. On the left menu, navigate to Access Points. Click Add New and enter the MAC address. Use the drop-down arrow to enter multiple MAC addresses at once or upload a CSV file. Repeat this process to add as many access points as required. 4. Connect device to internet over ethernet or an existing Datto mesh network. The device will then configure and start reporting status within a few minutes.

(4) T-Rail Clips (ceiling rail mount)

(1) Slim Ethernet Cable (for wall or junction box mount)

(1) Mounting Plate

(1) Ethernet Hole Cover Mounting Plate Slim Ethernet Cable Ethernet Hole Cover Access Point Larger, Fixed T-Rail Smaller, Adjustable T-Rail This access point is designed to be installed indoors or out, in several mounting positions. Regardless of how you mount this access point, keep the following in mind:

802.3af PoE input is required. Connect to any Datto Networking Switch, an 802.3af-compatible PoE switch or PoE injector. Place in the center of the room and away from any metallic surfaces. Signal primarily radiates to the front and sides. There is limited signal coverage directly behind it. Do not place heavy objects on the access point. Install in an area free from strong electromagnetic sources. Check the Ethernet cables to ensure they are fully secured to both the access point and PoE injector or switch. Do not install this access point in plenum spaces. Use the LED Light States STATE Online, Mesh Speed >2Mbps Online, Mesh Speed <=2Mbps Boot Loader Booting Up Firmware Upgrade CloudTrax Checkin Failure Key Re-pair LIGHT COLOR Solid Blue Flash Blue Solid Purple Solid Yellow Solid Red Flash White Flash Yellow Configuration Change AP not ready Solid White Net Failure - no default route Flash Red Wall or Solid Ceiling Mount T-Rail Ceiling Mount Attach the universal mounting plate to any solid surface

(screws are not included). For attaching to drop ceiling T-Rail or other T-Rail System. 1) Remove rear door and seal. 1) Remove rear door and seal. 2) Mount flat side of plate to wall or ceiling. 1) Remove rear door and seal. 2) Place all four T-Rail clips into mounting plate. Larger, Fixed T-Rail Smaller, Adjustable T-Rail 15/16" rails 9/16" rails ceiling mount instead. Access Point Overview Ethernet Port1, 802.3af PoE(48-54V=0.6A) Ethernet Por2, passive PoE(18-24V=1.34-1A) Mounting Bracket Overview LED indicator USB 2.0 Reset Button Cable Channel US single gang box US dual gang box Note: Ethernet port 1 is PoE input. The pass-through port (Ethernet 2) is data only. No power is passed through the second port. 3) Connect ethernet cable to device (Port 1). 4) Slide device down plate to lock in place. Ethernet port 1, 802.3af PoE 3) Place ethernet through mount and connect ethernet to device (Port 1). Slide mount onto device. Ethernet port 1, 802.3af PoE 4) Use the adjustable rail clips to tighten to the ceiling T-Rail until secure. T-Rail (not included)