About this product WARNING When riding your bicycle, do not stare at the computer for a long time. If you do not watch the road, you could hit an obstacle which might cause you to lose control, fall, and cause injury. IMPORTANT: To use the RIDEtime Elite computer, you must have an ANT+ compatible speed, cadence, or power sensor mounted on your bicycle. Compatible sensors:
Bontrager Duo Trap PN 508126 Bontrager Duo Trap S PN 437960 Bontrager Interchange Combo PN 438482 Bontrager ANT+/BLE Softstrap Heart Rate Belt Kit PN 519606 Other ANT+ compatible sensor To set up any other sensor, please refer to the manual that came with your sensor. Bontrager RIDEtime Elite Computer plus Duo Trap S Sensor 4 Duo Trap S 1 2 3 4 5 www.bontrager.com PN 580968 Parts list RIDEtime Elite Computer 1 2 3 6 5 6 7 8 9 10 1. Computer 2. Battery cover 3. 31.8mm handlebar shim 4. Out front mount 5. CR2032 battery 6. 22.2, 25.4 & 26.0mm handlebar shim Install battery 1 Install computer mount 1 2 2 1. Shim use: Determine the diameter of your handlebar. Use the thin shim with a 31.8mm handlebar. Use the thick shim with a 25.4 or 26.0mm handlebar. Use no shims with a 35mm handlebar. Use both shims with a 22.2mm handlebar. 2. Remove the rubber cover over the mounting clamp bolt. 3. Use a 2.5mm hex wrench to torque the bolt to 0.8 N-m (7 in-lb). 4. Replace the rubber cover over the clamp bolt. NOTE: The mount is not to be used with a cell phone. Mount computer Understanding the instructions Button location Quick press Multi press Long press
(2 seconds) Front Rear The letters indicate the order in which to push the buttons. More than one arrow means you should push the button until you see the value you want. Press and hold until next digit flashes to switch to next digit or field. Selection note:
Grey color represents flashing characters that show selected value. W BPM RPM KPH MPH Shows number of digits to be set. Screen icon Description Speed sensor is connected. Flashing if searching for sensor. Cadence sensor is connected. Flashing if searching. Heart rate monitor is connected. Flashing if searching. Power meter is connected. Flashing if searching. A service interval has been reached. Flashing is a prompt to clear. Transmitter signal when connected to compatible lights. Flashing if searching. Battery life is sufficient. Replacement when only 1/3 indicated. Enter and exit setup modes Rear button A C AC button Rear button Press the rear button once to enter Primary setup. Press and hold the rear button 5 seconds to enter Pairing and Advanced setup. Press the rear button for 5 seconds to exit either setup mode. In Ride mode you can press the rear button for 5 seconds to return you to the beginning of the Primary setup without changing any previously entered settings. NOTE: Do not use the rear button while riding. It will restart setup mode. Front button AC button 1. Gasket (alloy bikes) 2. Sensor with grommet and 2mm spacer installed (carbon bikes) 3. 8mm bike mounting screw 4. Speed magnet (wheel) 5. CR2032 battery 6. Cadence band shim 7. Large cadence band (crank) (26mm) W519998 8. Small cadence band with magnet
(crank) (9mm) W519999 9. Xsmall cadence band with magnet
(crank) (4mm) W534154 10. Plug (large cadence band) Install battery 1 2 Install Duo Trap S sensor (alloy bikes) 1 2 3 1. Remove the Duo Trap S cover from the chainstay. 2. Remove the grommet from the sensor. 3. Install the gasket onto the sensor with the notch facing forward as shown. 4 5 4. Install the sensor and gasket into the chainstay. 5. Hold the sensor into place and install the 8mm screw. 6. Use a 2.5mm hex tool to tighten the sensor. Install Duo Trap S sensor (carbon bikes) 1 2 6 3 m2.5N a b 1. Remove the Duo Trap S cover from the chainstay. 2. Remove the grommet from the sensor. 3. Fully insert the grommet into the chainstay. Make sure the grommet is flush with the chainstay. 4 4a 4b 5 2.5Nm 4. Install the sensor into the grommet in the chainstay. HINT: Hold the grommet in place with one hand and insert the sensor with the other hand as shown. 5. Hold the sensor in place and use a 2.5mm hex to install and tighten the 8mm screw. NOTE: Make sure the 2mm spacer is installed in the grommet before you tighten the screw. Mount speed magnet 1 2 a b c 90 180 1. Tighten the speed magnet on a spoke 2. Align the speed magnet with the marking on the sensor. 3. If necessary, rotate the magnet 90 or 180 to achieve sensor clearance. 4. Rotate the wheel and look for a red LED in the sensor to verify the magnet and sensor are in alignment. NOTE: The LED will illuminate for the first 10 revolutions only. Install small cadence magnet 1 2 3 145mm 4 135mm 1. Remove the non driveside pedal and install the small cadence magnet on the crank arm with the thick side nearest to the chainstay. 2. Align the magnet with the sensor. Press the AC button for a hard reset to return the computer to the factory default settings. Front button Alloy bikes: Align the magnet with the line on the sensor. Carbon bikes: Place the magnet 135mm or 145mm from the center of the bottom bracket to the center of the magnet Press the front button to scroll through the screens to find your desired setting. 3. Rotate the crank backwards. Look for the green LED on the cadence sensor to verify the magnet is correctly aligned. NOTE: The LED will illuminate for the first 10 revolutions only. 4. Optional: If the magnet is aligned but the LED does not illuminate, place a cadence band shim underneath the appropriate magnet. 5. If the small band does not fit between the crank and the chainstay, use the XS (4mm) cadence band provided. Install large cadence magnet 1 2 3 1. Remove the plastic cap from inside the small cadence band. 2. Remove the magnet from inside the small cadence band. 3. Insert the magnet fully inside the large cadence band so it is flush against the inside of the cavity. 4 5 4. Insert the plastic plug into the cavity of the large cadence band to hold the magnet in place. 5. Follow the steps in the Small cadence magnet installation to complete this installation. Primary setup 2 6 Road Mtb City 1 2 3... 10 W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH 3 7 24 Hr 12 Hr Lb Kg 11 W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH 1 5 9 Eng Deu Fra Esp Mi Km 1 2 3... 4 W BPM RPM KPH MPH
:
1 2 3... Press and hold until number flashes to switch between hours and minutes. 8 1 2 3... CUSTOM W BPM RPM KPH MPH W BPM RPM KPH MPH 1 2 3... NOTE: Custom wheel size is the circumference of the wheel in mm. See Wheel size chart. Road Mountain City Code Size 2124 29:2.2*
2136 29:2.3 (2.35) 2164 29:3.0 2190 27.5:2.2 2209 27.5:2.4 2227 27.5:2.8 2240 27.5:3.8 2253 27.5:4.5 2271 001-2999 26:2.0 26:2.2 26:3.8 26:4.7 Custom Code 2340 2359 2413 2221 2253 2309 2400 2485 2117 2148 2322 2403 01-2999 Size 700:28*
700:32 700:35 700:38 700:40 700:42 700:45 26:2.0 26:2.2 Custom Code 2164 2190 2209 2227 2240 2253 2271 2117 2148 01-2999 Size 700:23*
700:25 700:28 700:32 700:35 700:38 700:40 700:42 700:45 Custom
*Default Measure your wheel size 1. With the valve stem of the wheel directly over the floor, mark the floor at the valve stem. Ride mode To wake the computer: Push any button or spin the wheel. 2. Roll the bike forward one revolution of the wheel so that the valve stem is again directly over the floor. The default Ride mode is shown with all sensors connected, and Speed is selected as the primary metric. 3. Mark the new location of the valve stem. Sensors that are not connected or that are disabled will not be displayed and will be skipped. 4. Measure the distance between the marks. Measurements in mm are required. The computer will turn off after 10 minutes of inactivity. NOTE: If you do not have a speed sensor, the timer will still run if you have a cadence sensor or power meter. W BPM RPM KPH MPH To reset the timer, hold down the front button for 5 seconds from any Ride mode screen. Distance Dual View
(only if Dual View is on) Avg Max
(speed) W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH Cadence Avg Max
(heart rate) Calories Scan
(if enabled) W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH Avg Max
(cadence) Power Odometer If the wrench icon is displayed, advance to this screen, otherwise return to Ride mode. W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH Heart Rate Avg Max
(power) Clock Back to Ride mode No Yes Press the front button for 5 seconds to prompt the clear data question. Yes No Night mode W BPM RPM KPH MPH On Off Press the front button for 10 seconds to prompt the Night mode OFF/ON question. Night mode will enable the backlight. In Night mode, the first button press activates the backlight for 5 seconds and does not advance the carousel. Each additional press extends the backlight for 5 seconds, and advances the carousel. When Night mode is OFF, the backlight is disabled. If lights are connected, Night Mode setting will determine Light Mode. When paired with Bontrager lights, the following table shows what mode the lights are in:
Headlight Taillight Night Mode ON Medium steady Night flash Night Mode OFF Day flash Day flash Trek Bicycle Corporation Contact information:
North America Trek Bicycle Corporation 801 West Madison Street Waterloo, WI 53594 Tel: 800-313-8735 Europe Bikeurope BV Ceintuurbaan 2-20C 3847 LG Harderwijk The Netherlands Tel: +31 (0)33 45 09 060 Statements of regulatory compliance FCC Compliance RIDEtime Elite Computer FCC ID: O4GRTELITE IC: 7666A-RTELITE Duo Trap S FCC ID: O4GDUOTRAPS IC: 7666A-DUOTRAPS Transmission Frequency: 2.4GHz Bluetooth: 2402MHz ~ 2480MHz ANT+: 2457MHz Bluetooth Max Power: <6dBm ANT+ Max Power: <6dBm Operating power: 3 V D C Operating temperature: 0C~50C RF exposure compliance distance is 20 millimeters. These devices comply with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or experienced radio / TV technician for help. CAUTION: Any changes or modifications not expressly approved by Trek Bicycle Corporation could void the users authority to operate the equipment. NOTE: TREK BICYCLE CORPORATION IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. Industry Canada Compliance This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Leprsent appareil est conforme aux CNR dIndustrie Canada applicable aux appareils radio. Exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilsateur de lappareil doit accepter tout brouillage radiolectrque subi, meme si le brouillage est susceptible den compromettre le fonctionnement. This Bontrager equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The radiated output power of the Transmitr Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Status of the listing in the Industry Canadas REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng Additional Canadian information on RF exposure also can be found at the following web address:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html Cet appareil est conforme aux limites dexposition la frquence radio (FR) dIC et de FCC. La puissance de sortie mise par lappareil de sans fil Transmitr est infrieure la limite dexposition aux frquences radio dIndustry Canada (IC). Cet appareil est en contact direct avec lutilisateur dans des conditions normales dutilisation. Lmetteur ne doit pas tre co-implment ou utilis conjointement avec une autre antenne ou un autre metteur. Ce priphrique est homologu pour lutilisation au Canada. Pour consulter lentre correspondant lappareil dans la liste dquipement radio (REL - Radio Equipment List) dIndustry Canada rendezvous sur: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=fraPour des informations supplmentaires concernantlexposition aux RF au Canada rendezvous sur:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html European Union Compliance Trek Bicycle Corporation and Bontrager hereby declare that the wireless devices identified as RIDEtime Elite Computer and Duo Trap S Sensor are in compliance with the following European Directives:
RED 2014/53/EU EMCD 2014/30/EU LVD 2014/35/EU RoSH Directive 2011/65/EU The full text of the EU declaration of conformity is available from your bike shop, or at the following internet address: http://www.bontrager.com/support 12 13 W BPM RPM KPH MPH OFF 1 Hr 3 Hr 6 Hr
...24 Hr Pairing and Advanced setup Pairing 1 3 2 W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH NOTE: If you have no paired sensors, youll be taken to Pairing and Advanced setup upon completion of Primary setup. NOTE: When Auto Clear is set, the number represents the amount of inactive time before the last rides data is cleared. NOTES:
1. If you select ALL, the computer will look to pair all nearby devices. If you want to look for a specific type of sensor (speed, cadence, heart rate, or power) then select that choice. 2. If you want to pair more than one sensor but not all, pair one sensor at a time. Repeat the procedure for each sensor. 3. To exit and advance to the Pair lights step, press the rear button. ALL Speed Cadence Heart Power NOTE: Symbols flash during search and become steady once found. You can exit pairing, and advance to the next step once the desired symbols stop flashing. Otherwise the system will advance in 30 seconds. W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH Power meter calibration (If power meter sensor is not paired, computer will advance to step 5.) 4 12380 40277
... NOTE: These are paired sensor IDs. W BPM RPM KPH MPH W BPM RPM KPH MPH OR W BPM RPM KPH MPH Follow the power meter guidelines to calibrate your power meter for the most accurate reading. Retry Pair lights 5 6 Yes No Yes No Enable lights (If lights are not paired, computer will advance to step 6.) 1. If Pair Lights is enabled (YES), the computer will enter search mode, and
) will flash. Hold the computer close to the desired the transmitter icon (
light to be paired. W BPM RPM KPH MPH 2. If a light is detected:
The computer will display FOUND. The light sensor ID and the transmitter icon will display for 2.5 seconds. The light turns on for 2.5 seconds, then turns off. 3. The unit will continue to search for up to three lights. To exit the search, press the rear button. NOTE: If you accidentally pair a light, press the AC button to delete all lights. Then pair to only the lights desired. NOTES:
If Auto Lights is enabled (YES):
1. The computer will turn your paired light(s) on when speed is detected above 3 mph. 2. The lights will remain on until speed drops below 1 mph for longer than 3 W BPM RPM KPH MPH minutes. 3. The computer will not override:
Manual input to the lights. Input from a light pairing with another computer or a remote control. If Auto Lights is disabled (NO):
4. The paired light(s) will remain stored as saved connections. 5. The computer does not try to form a connection with the lights. There are three occurrences when a command is sent to the lights to change their settings:
Turn ON when speed above 3 mph is detected. Turn OFF when speed below 1 mph is detected for longer than 3 minutes. Change mode when Night mode state is changed. Light setting NOTES:
1. The computer should turn the lights ON to the appropriate mode based on whether Night Mode is enabled or disabled. 2. See light mode table in Night mode section. 3. In ride mode, if the battery level of a connected light reaches critically low, the transmitter icon will flash and the display will flash LOW BATTERY LIGHTS (low batt! in the middle display and LIGHTS in the lower display). Low battery detection In ride mode, if the battery level reaches critically low:
The transmitter icon will flash continuously and the display will show LOW BATTERY LIGHTS for 2.5 seconds. The LOW BATTERY LIGHTS message will be repeated every 30 seconds. Display 7 8 W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH Yes No Yes No Yes No Speed Cadence Heart Power Yes No W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH Yes No Yes No Yes No Yes No W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH Speed Cadence Heart Power Speed Cadence Heart Power Yes No 9 Yes No NOTES:
These screens will be displayed only if Dual View was selected (YES) in step 9. If NO is selected in any of the display screens in step 8, that metric will not be available in the Scan display. Display customization 10 W BPM RPM KPH MPH All Off Custom W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH Yes No Yes No Yes No Yes No Yes No NOTES:
1. If you choose ALL, the computer will scan all metrics (Speed, Cadence, Heart rate, Power, Lights). 2. If you choose OFF, you will not have the option to scan. W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH W BPM RPM KPH MPH Yes No Yes No Yes No Yes No Yes No NOTE: Sensors disabled during step 10 will not show either the instantaneous screen or the AVG/MAX screen. 11 W BPM RPM KPH MPH