FCC ID: TSV-HHB2BATR Wireless Sensor

Temperature Sensor Temperature Sensor Components Home Key Slide Channel Antenna Attach enclosed adhesive on back for placement Temperature Sensor Uses:

Bedroom Attic Basement Living Room Office Garage Kitchen Cellar Bathroom Tool Shed Loft Storage Area FCC Statement

(Compliance Statement, Part 15.19): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING (Part 15.21): Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. To comply with FCCs RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Statement The term IC before the certification/registration number only signifies that the Industry Canada technical specifications were met. Interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, then the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into a power source on different circuit than the receiver. Sensor Maintenance and Battery Replacement Cleaning the sensor Clean with a soft, dry cloth. To check sensor battery level Using the Home Key, highlight the sensor icon. Click the thumbwheel once and note the battery status on the bottom line of the screen. To check if sensor battery is low or depleted When sensor battery is low, a flashing low battery icon appears on the Home Key above the sensor icon, and the screen is amber in color. When a battery is depleted, a question mark will appear above sensor icon. Replacing a depleted battery Remove the depleted battery and replace with one lithium CR123A 3V battery, available through the Internet and anywhere camera and camcorder supplies are sold. IM00416015E Part No.: 68B5040H11 2008 Eaton Corporation

Temperature Sensor Set up CARRY the sensor, battery, and the Home Key to the location where you want to place it. OPEN the sensor cover and insert the battery. The green LED light inside the sensor should flash four times if the battery is good. Close the cover. CLICK the Home Key thumbwheel to wake the screen, and SLIDE the Home Key into the Slide Channel on the top of the sensor. The Home Key screen should say:

Please wait Device found OK to remove Key. Device found OK to remove Key... Follow the instructions on the Home Key screen to join the sensor to the system, name it, and set In-Home Awareness and "CallMe"

Awareness. After options are set and you click Done, go back?, the Home Key screen will indicate that the sensor is joined to the system. You may go to Step 2. If you slide the Home Key into the sensor Slide Channel and the Home Key screen shows either of the following messages, it means that the Home Key or sensor may be outside the range of the Base Station. Remove Key... Please try again Sensor out of range?

Remove Key... Can't set up now Key out of range If the Home Key or sensor is out of range, you can:

Add a Home Heartbeat Range Extender between the Base Station and Sensor, or Select an alternate location for the Sensor, or Try moving the Base Station to a more central location in your home. Then, complete Step 1 again. Test ROLL OVER and highlight the Temperature Sensor icon on the Home Key. The initial temperature threshold of your Temperature Sensor is set at 40 F. Check that the sensor reports 'Above temp' on the Home Key at room temperature. DOUBLE-CLICK the Home Key thumbwheel on the Temperature Sensor icon to reveal Above temp for 5 secs the control menu. Use the 'Change threshold?' option to set a new temperature threshold above room temperature, e.g. 100 F. Temp Sensor Slide the Home Key into the Slide Channel of the Temperature Sensor. If the Home Keyis not out of range, the new threshold setting will now be registered with the sensor. Temp Sensor Below temp for 5 secs Check that at room temperature the sensor reports 'Below temp' on the Home Key for the 100 F threshold setting. Place and use MOUNT the Temperature Sensor in the measurement location by attaching the enclosed adhesive tape on the back .*

Set the required temperature threshold using the Home Key, following the procedure described in the test. If you would like an immediate temperature threshold update, slide Home Key into the sensor Slide Channel. Otherwise, please allow up to one hour for the new settings to take effect.

* Be sure that the area of installation is clean and dry. Need help? Call 1-800-813-2199 for customer support or visit www.homeheartbeat.com If Your Temp Sensor . will not respond, make sure the battery in the sensor is installed correctly. does not send a signal to the Base Station, move the sensor and Base Station closer together (or consider getting a Home Heartbeat Range Extender).