FCC ID: WL6-718020QT1C 7c Modular Platform

QSIP7180 Module Instruction Document Elitegroup Computer Systems Co., Ltd. No. 239, Sec. 2 Ti Ding Blvd., Taipei, Taiwan 11493 The QSIP7180 has two baseline regulatory certification variants:

- Windows or Chromebook for WWAN + Wi-Fi/BT

- Regulatory Model: QSIP7180 FCC ID:WL6-718020QT1C Note:

This module will not be sold separately, this file is only for FCC application. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help. CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This device is slave equipment, the device is not radar detection and not ad-hoc operation in the DFS band. This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:

WL6-7180QT201C. The final end product must be labeled in a visible area with the following Contains FCC ID:

47CFR Rules Parts Addressed in Modular Certification Band Applicable FCC Rule Part Band 5 Band 2 Band 46 47CFR47 Part 22 47CFR47 Part 24 47CFR47 Part 15 Subpart E Other 3GPP Bands 47CFR47 Part 27 Wi-Fi 2.4 GHz 47CFR47 Part 15.247 Bluetooth 2.4 GHz 47CFR47 Part 15.247 Wi-Fi 5GHz 47CFR47 Part 15 Subpart E Receive Mode 47CFR47 Part 15 Subpart B Test Standards ANSI C63.10 (Unlicensed) ANSI C63.26 (Licensed) Module Guidance KDB Publication 996369 WWAN KDBs 1 2 3 This FCC ID: WL6-718020QT1C has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. The module is certified for use only with certain antennas described in this chapter. For 4GHz/5GHz unlicensed band: Allowed antenna type: PIFA No. Antenna Type Peak Gain PIFA Antenna 3.62 dBi for 2.4 GHz PIFA Antenna 3.08 dBi for 5.150~5.350 GHz PIFA Antenna 4.46 dBi for 5.470~5.850 GHz Note:

The antenna connector is I-PEX type. For WWAN licensed bands:

Allowed maximum gain (dBi), including antenna cable loss US FCC Antenna Gain (dBi) Band 2: US 4: US 5: US 7: US 12: US 13: US 14: US 17: US 25: US 26: US 30: US 66: US 71: US 38: US 5 5.8 2.1 5.4 0.9 1.3 1.8 0.9 5.1 2.1 0 5.9 1.1 5.2 Integrated Product Test and Certification Requirements Integrators must adhere to test guidance provided in FCC KDB 996369 D04 available at this https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=44637 1. The module has been approved for the rule parts defined in Table 4-1. Host device must be tested for 2. Radiated emissions testing should be tested per KDB 996369 with all transmitters active and transmitting at max transmit power. A ECS account representative can assist with making test tools available as website:

Part15B compliance. needed. 3. The recommended method of test is to use a call box simulator for WWAN where the UE is configured for maximum transmit power. For WLAN testing, if an access point is not available for mission mode testing, Qualcomm test tools can be used to configure the WLAN modem for maximum transmit power and the desired mode/frequency of operation. 4. If a memory variant is utilized, limited WWAN and Wi-Fi transmitter testing should be completed to ensure equivalent compliance. The following testing must be completed at a minimum Limited unlicensed band edge measurement and unwanted radiated spurious emissions Radiated emissions in FCC Part 15.205 restricted bands during Wi-Fi and BT operation

Limited WWAN radiated emissions Part 15B testing NOTE: Data can be leveraged from the part of Part 15B and radiated emissions referenced above to address continued compliance with the variant memory. 5. RF Exposure must be addressed at the host level for all portable products where users are less than 20cm from the device during normal operation (i.e. SAR testing is required) in accordance with FCC KDB 447498. Host product manufactures must provide all required documentation to the end user. 6. Antennas must follow the guidelines defined in Section 7. 7. In the US, either a Class II Permissive Change or new equipment authorization is required. Data can be leveraged from FCC ID:WL6-718020QT1C per FCC KDB 484596.

ESS ELITEGROUP Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 USA Subject: Declaration of Changing ID, FCC ID: WL6-718020QT1C Date: March 3, 2022 To Whom It May Concern, We, ELITEGROUP COMPUTER SYSTEMS CO., LTD, would like to proceed a change ID project. Original application information:

Company name: Qualcomm Technologies, Inc. FCC ID: J9CQSIP7180 Product name: 7c Modular Platform Model name: QSIP7180 Original issued date: 10/13/2020 We would like to market the above referenced product under our FCC ID: WL6-718020QT1C and model no. is QSIP7180. All other hardware and software is identical with original granted. This application has been authorized by Intel Mobile Communications. We would like to declare that WL6-718020QT1C is electrically identical and the only changed is the label on the device. The original test results continue to be representative of and applicable to the changed equipment. Sincerely, unl bus Oe La. Sunny Kuo/Setion Manager ELITEGROUP COMPUTER SYSTEMS CO., LTD

Qualcomm Technologies, Inc. 5775 Morehouse Drive, San Diego, CA 92121 www.qualcomm.com Tuesday, March 01, 2022 To:

Elitegroup Computer Systems Co., Ltd. No.239, Sec. 2, Tiding Blvd., Neihu Dist., Taipei City, 114755 Taiwan Re: Change of Identification Authorization FCC ID: J9CQSIP7180 To Whom It May Concern:

This letter grants authorization for representatives of Elitegroup Computer Systems Co., Ltd. to apply to the FCC for a change in identification as specified under 47CFR2.933 of the FCC rules. This authorization applies to Qualcomm Technologies, Inc., 7c Modular Platform, FCC ID J9CQSIP7180, granted on 10/13/2020. The modules new FCC ID will be WL6-

718020QT1C. The equipment is electrically identical the only change being the labels on the device. The original test results continue to be representative of and applicable to the changed equipment. Best Regards Stanley Lin Wireless Regulatory, Staff, EMC-Regulatory Qualcomm Technologies, Inc. slin@qti.qualcomm.com

Qualcomm Technologies, Inc. 5775 Morehouse Drive, San Diego, CA 92121-1714 www.qualcomm.com November 13, 2019 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Authorization of Handling FCC Regulatory Applications FCC Identifier J9C To Whom It May Concern:

I, hereby, authorize Mr. Stanley Lin, to handle FCC Regulatory related applications for Qualcomm Technologies, Inc. FCC Identifier J9C and sign all required application documents. Best Regards, Paul Guckian VP, Engineering Qualcomm Technologies, Inc. 5775 Morehouse Drive San Diego, CA 92121 Office: 858-651-1547 pguckian@qti.qualcomm.com

EES ELITEGROUP Declaration of Authorization We Name: ELITEGROUP COMPUTER SYSTEMS CO., LTD Address: No.239, Sec.2,Ti Ding Blvd., City: Taipei, Country: Taiwan Declare that:

Name Representative of agent: Stanley Wu Agent Company name: DEKRA Testing and Certification Co., Ltd. Address: No. 26, Hwaya 1st Road., Guishan District, City: Taoyuan 33341, Country: Taiwan is authorized to apply for Certification of the following product(s):

Product Name: 7c Modular Platform Model: QSIP7180 FCC ID: WL6-718020QT1C Trademark: ECS ELITEGROUP on our behalf. This is valid until Feb. 22 2023, or until FCC certification are completed, whichever comes sooner. Date: 3/3/2022 City: Taipei Name: Sunny Kuo Function: Section Manager Signature: ae Vie 5 Se =