HARDWARE USER MANUAL GWS-CSCG Tag Logistics Monitoring Tag Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio technician for help Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the systems manufacturer could void the users authority to operate the equipment. FCC Label Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undersired opreation RF Exposure Warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. 1 Canada, Industry Canada (IC) Notices This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis dIndustry Canada (IC) Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a persons body). Informations concernant lexposition aux frquences radio
(RF) La puissance de sortie mise par lappareil de sans fil est infrieure la limite dexposition aux frquences radio dIndustry Canada (IC). Utilisez lappareil de sans fil de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a galement t valu et dmontr conforme aux limites dexposition aux RF dIC dans des conditions dexposition des appareils mobiles
(antennes sont suprieures 20 cm partir du corps dune personne). 2 Safety Instruction Your system is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heated source such as a radiator. Set up the system on a stable surface. Openings on the chassis are for ventilation. Do not block or cover these openings. Make sure you leave plenty of space around the system for ventilation. Never insert objects of any kind into the ventilation openings. If you use an extension cord, make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating. Attention during use If you encounter the following technical problems with the product, unplug the power cord and contact a qualified service technician or your retailer. The power cord or plug is damaged. Liquid has been spilled into the system. The system does not function properly even if you follow the operat-
ing instructions. The system was dropped or the cabinet is damaged. The system performance changes The warranty does not apply to products that have been disassembled by users. Safety Notice and warnings Product disposal notice IMPORTANT:
In the European Union, this symbol indicates that this product including battery must not be disposed of with household waste. It is your responsibility to hand it over to a designated collection point for the recycling of waste electrical and electronic equipment. For more information, please contact your local waste collection center or the point of purchase of this product. CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. 3 Nordic Lithium Safety Notice (for lithium-ion batteries) Safety Notice:
Danger of explosoin if battery is incorrectly replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions. Attetion during use 1. Do not place this product underneath heavy loads or in an unstable position. 2. Do not use or expose this product around magnetic fields as magnetic interference may affect the performance of the product. 3. Do not storage this product to high levels of direct sunlight, high-humidity or wet conditions. 4. Do not carry the product on the body (or pockets). CE marking FCC marking 4 Brief Introduction Specifications Item Spec Description MCU LED Connectivity Sensors Battery Type Operating Temperature Dimension (W x L x H) IP Level
< 4 cm 30 m Telink 8269f512 ET32 3 Color LED (RGB) NFC Zigbee Temp/Humidity Ambient Light G-Sensor GR2450
-20~60 76* 70 *11 (mm) IP54 5 Tag exterior overview 6 How to use GWS-CSCG Step 1: Power On/Off 1. Power On - Press button three times. On third press user must hold button down for 20 seconds. If successful: Power icon on reflecting battery charge status on display, green LED pattern and positive audio chime. If unsuccessful: Power icon reflecting insufficient battery on display, red LED light pattern and negative audio chime. 2. Power Off - Press button three times. On third press user must hold button down for 20 seconds. User will not be able to power down device if the shipment is still active. If successful: Power icon on reflecting battery charge status on UI, green LED pattern and positive audio chime. If unsuccessful: Power icon will be reflected on UI, red LED light pattern and negative audio chime. 7 Step 2: NFC Tag Pairing Tap powered on Gateway to Tag and press the NFC button to pair the Tag to the Gateway. 8 Step 3: Load shipment When loading pallets with Tags and Gateways onto a truck, try to place one pallet in the back of the truck, one pallet in the center of the truck and one pallet with the Gateway right by the door. Make sure that the Gateway faces the truck door, and is as close to the door as possible to ensure the Gateway signal can best maintain cell connectivity. 9 How to Power On Tag By pulling the battery strip away from the Tag, the tag will be power-on with LED light blink. How to Attach Tag to Cargo Via Screws:
Via Self-tape:
By apply screws through the 2 mounting holes on the corner of tag, it can be secure to any wooden crate or box for transportation. By peeling off the back film and attache the tag to the side of shipping carton. 10 GWS-CSCG Tag Logistics Monitoring Tag