TA80TA1 Motherboard Guide FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm 1 from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID:
WL6-TABC8TA1 Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This radio transmitter FCC ID: WL6-TABC8TA1 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List No. Manufacturer Part No. Antenna Peak Gain Type 1 2 JEM WGT 13H130-
JV8070 13H130-
JV8050 PCB Antenna 2.85 dBi for 2.4GHz PCB Antenna 1.77 dBi for 2.4GHz Note: The antenna connector is I-PEX type. 2 Motherboard layout Main components No. A B C Name Charger IC CPU+PMIC+DDR+
EMMC+CODEC GPS IC 3 No. D E F Name WiFi/BT IC Rear facing camera Microphone System connectors No. 1 2 3 4 Name Battery Connector LCD Connector GPS Antenna Connector WiFi Antenna Connector No. 5 6 7 Name Speaker Connectors Side Key FPC Connector TP Connector I/O Ports 4 No. 1 2 3 Name Ultrastick Connector Micro USB Connector Audio Jack No. 4 5 Name T-Flash Connector Mini HDMI port 5 Features Processor Memory Graphics Storage Wireless Display Cameras Control Antenna IntelBayTrail-TZ3735E Quad core Base 1.33 GHz, Burst to 1.83GHz, 2MB L2 Cache DDR3L-RS 1333, 1 x 32-bits 1GB (Default) / 2GB (Optional) Intel HD Graphics (Gen 7 gfx) Max resolution upto1280x800 Single eMMC v4.5.1 Default 16 GB Wi-Fi 802.11 b/g/n Bluetooth 3.0 w/o high speed supported MIPI interface Support 10-point multi-touch FrontCamera:2.0M Rear Camera:5.0M 802.11b/g,n, BT: 2.4GHz; GPS 6 Input/Output 1 x MicroUSB 2.0, OTG port
(Type A/B) 1 x Mic/head phone jack combo
(American type) 1 x Micro HDMI 1.4 1 x Micro SD card slot (Support 128M-32G TF Card) 1 x Analog MIC Speaker & Mic Build-in Speaker x 2 Internal Analog MIC x 1 7