ESP8684-MINI-1U User Manual Small-sized 2.4 GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 module Built around ESP8684 series of SoCs, RISC-V single-core microprocessor 14 GPIOs Sleeve monopole antenna connector ESP8684-MINI-1U www.espressif.com Version0.5 Espressif Systems Copyright 2023 1 Module Overview 1 Module Overview 1.1 Features CPU and On-Chip Memory Bluetooth ESP8684H2 or ESP8684H4 embedded, 32-bit Bluetooth LE: Bluetooth 5 RISC-V single-core processor, up to 120 MHz 576 KB ROM 272 KB SRAM (16 KB for cache) SiP flash (see details in Table 1) Access to flash accelerated by cache Supports flash in-Circuit Programming (ICP) High power mode22 dBm Speed: 1 Mbps, 2 Mbps Advertising extensions Multiple advertisement sets Channel selection algorithm #2 Wi-Fi 802.11 b/g/n Internal co-existence mechanism between Wi-Fi and Bluetooth to share the same antenna Peripherals Center frequency range of operating channel:
2412 ~ 2462 MHz GPIO, SPI, UART, I2C, LED PWM controller, general DMA controller, temperature sensor, SAR Supports 20 MHz bandwidth in 2.4 GHz band ADC 1T1R mode with data rate up to 72.2 Mbps Note:
Wi-Fi Multimedia (WMM) TX/RX A-MPDU, TX/RX A-MSDU Immediate Block ACK Fragmentation and defragmentation Transmit opportunity (TXOP)
* Please refer to ESP8684 Series Datasheet for de-
tailed information about the module peripherals. Integrated Components on Module 26 MHz crystal oscillator Automatic Beacon monitoring (hardware TSF) Antenna Options 3 virtual Wi-Fi interfaces sleeve monopole antenna via a connector Simultaneous support for Infrastructure BSS in
(ESP8684-MINI-1U) Station mode, SoftAP mode, Station + SoftAP mode, and promiscuous mode Operating Conditions Note that when ESP8684 series scans in Station mode, the SoftAP channel will change along with Operating voltage/Power supply: 3.0 ~ 3.6 V the Station channel Operating ambient temperature: 40 ~ 105 C 1.2 Description ESP8684-MINI-1U is a general-purpose Wi-Fi and Bluetooth LE module. The rich set of peripherals and a small size make the two modules an ideal choice for smart homes, industrial automation, health care, consumer electronics, etc. Espressif Systems 2 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 1 Module Overview The series comparison for the module is as follows:
Table 1: ESP8684-MINI-1U (CONN) Series Comparison Ordering Code SiP Flash ESP8684-MINI-1U-H2 ESP8684-MINI-1U-H4 2 MB 4 MB Ambient Temp.1
(C) Size
(mm) 40 ~105 13.2 12.5 2.4 1 Ambient temperature specifies the recommended temperature range of the environment immediately outside the Espressif module. ESP8684-MINI-1U comes with a connector for an sleeve monopole antenna. ESP8684-MINI-1U is available in two variants that integrate the ESP8684H2 and ESP8684H4 chip respectively. The ESP8684H2 and the ESP8684H4 chip fall into the same category, namely ESP8684 chip series. ESP8684 series of chips have a 32-bit RISC-V single-core processor. They integrate a rich set of peripherals, ranging from UART, I2C, LED PWM controller, general DMA controller, temperature sensor, and SAR ADC. It also includes SPI, Dual SPI and Quad SPI interfaces. ESP8684H2 and ESP8684H4 chip vary only in the size of system in package (SiP) flash. For details, please refer to ESP8684 Series Comparison in ESP8684 Series Datasheet. 1.3 Applications Generic Low-power IoT Sensor Hub Smart Building Generic Low-power IoT Data Loggers Industrial Automation Cameras for Video Streaming Over-the-top (OTT) Devices USB Devices Speech Recognition Image Recognition Mesh Network Home Automation Smart Agriculture Audio Applications Health Care Applications Wi-Fi-enabled Toys Wearable Electronics Retail & Catering Applications Espressif Systems 3 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 Contents Contents 1 Module Overview 1.1 Features 1.2 1.3 Description Applications 2 Pin Definitions 2.1 Pin Layout 2.2 Pin Description 3 Get Started 3.1 What You Need 3.2 3.3 Hardware Connection Set up Development Environment 3.3.1 Install Prerequisites 3.3.2 Get ESP-IDF 3.3.3 3.3.4 Set up Tools Set up Environment Variables 3.4 Create Your First Project 3.4.1 Start a Project 3.4.2 Connect Your Device 3.4.3 Configure 3.4.4 Build the Project 3.4.5 Flash onto the Device 3.4.6 Monitor 4 U.S. FCC Statement 5 Industry Canada Statement 6 Related Documentation and Resources Revision History 2 2 2 3 5 5 5 7 7 7 8 8 9 9 9 9 9 9 10 10 11 12 14 18 21 22 Espressif Systems 4 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 2 Pin Definitions 2 Pin Definitions 2.1 Pin Layout The pin diagram below shows the approximate location of pins on the module. Figure 1: Pin Layout (Top View) 2.2 Pin Description The module has 53 pins. See pin definitions in Table 2 Pin Definitions. For peripheral pin configurations, please refer to ESP8684 Series Datasheet. Table 2: Pin Definitions Name No. Type1 Function GND 3V3 NC IO2 IO3 1, 2, 11, 14, 36-53 3 4, 7, 9, 10, 15, 17, 24, 25, 27, 28, 29, 32-35 P P Ground Power supply Not connected 5 6 I/O/T GPIO2, ADC1_CH2, FSPIQ I/O/T GPIO3, ADC1_CH3 Espressif Systems 5 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 Contd on next page Pin 49GNDGNDGNDGNDGNDGNDGNDGNDGNDPin 1Pin 2Pin 3Pin 4Pin 6Pin 5Pin 7Pin 8Pin 9Pin 10Pin 11Pin 53GNDPin 52GNDPin 12Pin 13Pin 14Pin 15Pin 16Pin 17Pin 18Pin 19Pin 20Pin 21Pin 22Pin 23Pin 24Pin 25Pin 51GNDPin 26Pin 27Pin 28Pin 29Pin 30Pin 31Pin 32Pin 33Pin 34Pin 35Pin 50GNDPin 36Pin 37Pin 38Pin 39Pin 40Pin 41Pin 42Pin 43Pin 44Pin 45Pin 46Pin 47Pin 48GNDGND3V3NCIO2IO3NCENNCNCGNDIO0IO1GNDNCIO10NCIO4IO5IO6IO7IO8IO9NCNCIO18NCNCNCRXD0TXD0NCNCNCNCGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGND 2 Pin Definitions Name No. Type1 Function Table 2 contd from previous page EN IO0 IO1 IO10 IO4 IO5 IO6 IO7 IO8 IO9 IO18 RXD0 TXD0 8 12 13 16 18 19 20 21 22 23 26 30 31 High: on, enables the chip. I Low: off, the chip powers off. Note: Do not leave the EN pin floating. I/O/T GPIO0, ADC1_CH0 I/O/T GPIO1, ADC1_CH1 I/O/T GPIO10, FSPICS0 I/O/T GPIO4, ADC1_CH4, FSPIHD, MTMS I/O/T GPIO5, FSPIWP, MTDI I/O/T GPIO6, FSPICLK, MTCK I/O/T GPIO7, FSPID, MTDO I/O/T GPIO8 I/O/T GPIO9 I/O/T GPIO18 I/O/T GPIO19, U0RXD I/O/T GPIO20, U0TXD 1 P: power supply; I: input; O: output; T: high impedance. Note:
IO0, IO1, IO3, IO5/MTDI pins have low-level glitches during chip power up. See details in section General Purpose Input
/ Output Interface (GPIO) of ESP8684 Series Datasheet. Espressif Systems 6 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 3 Get Started 3 Get Started 3.1 What You Need To develop applications for module you need:
1 x ESP8684-MINI-1U 1 x Espressif RF testing board 1 x USB-to-Serial board 1 x Micro-USB cable 1 x PC running Linux In this user guide, we take Linux operating system as an example. For more information about the configuration on Windows and macOS, please refer to ESP-IDF Programming Guide for ESP8684. 3.2 Hardware Connection 1. Solder the ESP8684-MINI-1U module to the RF testing board as shown in Figure 2. Figure 2: Hardware Connection 2. Connect the RF testing board to the USB-to-Serial board via TXD, RXD, and GND. 3. Connect the USB-to-Serial board to the PC. Espressif Systems 7 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 3 Get Started 4. Connect the RF testing board to the PC or a power adapter to enable 5 V power supply, via the Micro-USB cable. 5. During download, connect IO0 to GND via a jumper. Then, turn ON the testing board. 6. Download firmware into flash. For details, see the sections below. 7. After download, remove the jumper on IO0 and GND. 8. Power up the RF testing board again. The module will switch to working mode. The chip will read programs from flash upon initialization. Note:
IO0 is internally logic high. If IO0 is set to pull-up, the Boot mode is selected. If this pin is pull-down or left floating, the Download mode is selected. For more information on ESP8684-MINI-1U, please refer to ESP8684 Series Datasheet. 3.3 Set up Development Environment The Espressif IoT Development Framework (ESP-IDF for short) is a framework for developing applications based on the Espressif ESP32. Users can develop applications with ESP8684 in Windows/Linux/macOS based on ESP-IDF. Here we take Linux operating system as an example. 3.3.1 Install Prerequisites To compile with ESP-IDF you need to get the following packages:
CentOS 7 & 8:
1 2 sudo yum -y update && sudo yum install git wget flex bison gperf python3 python3-
pip python3-setuptools cmake ninja-build ccache dfu-util libusbx Ubuntu and Debian:
sudo apt-get install git wget flex bison gperf python3 python3-pip python3-
setuptools cmake ninja-build ccache libffi-dev libssl-dev dfu-util libusb-1.0-0 sudo pacman -S --needed gcc git make flex bison gperf python-pip cmake ninja ccache dfu-util libusb 1 2 Arch:
1 2 Note:
This guide uses the directory ~/esp on Linux as an installation folder for ESP-IDF. Keep in mind that ESP-IDF does not support spaces in paths. Espressif Systems 8 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 3 Get Started 3.3.2 Get ESP-IDF To build applications for ESP8684-MINI-1U module, you need the software libraries provided by Espressif in ESP-IDF repository. To get ESP-IDF, create an installation directory (~/esp) to download ESP-IDF to and clone the repository with git clone:
1 mkdir -p ~/esp 2 cd ~/esp 3 git clone --recursive https://github.com/espressif/esp-idf.git ESP-IDF will be downloaded into ~/esp/esp-idf. Consult ESP-IDF Versions for information about which ESP-IDF version to use in a given situation. 3.3.3 Set up Tools Aside from the ESP-IDF, you also need to install the tools used by ESP-IDF, such as the compiler, debugger, Python packages, etc. ESP-IDF provides a script named install.sh to help set up the tools in one go. 1 cd ~/esp/esp-idf 2 ./install.sh 3.3.4 Set up Environment Variables The installed tools are not yet added to the PATH environment variable. To make the tools usable from the command line, some environment variables must be set. ESP-IDF provides another script export.sh which does that. In the terminal where you are going to use ESP-IDF, run:
1 . $HOME/esp/esp-idf/export.sh Now everything is ready, you can build your first project on ESP8684-MINI-1U module. 3.4 Create Your First Project 3.4.1 Start a Project Now you are ready to prepare your application for ESP8684-MINI-1U module. You can start with get-started/hello_world project from examples directory in ESP-IDF. Copy get-started/hello_world to ~/esp directory:
1 cd ~/esp 2 cp -r $IDF_PATH/examples/get-started/hello_world . There is a range of example projects in the examples directory in ESP-IDF. You can copy any project in the same way as presented above and run it. It is also possible to build examples in-place, without copying them first. 3.4.2 Connect Your Device Now connect your module to the computer and check under what serial port the module is visible. Serial ports in Linux start with /dev/tty in their names. Run the command below two times, first with the board unplugged, then with plugged in. The port which appears the second time is the one you need:
Espressif Systems 9 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 3 Get Started 1 ls /dev/tty*
Note:
Keep the port name handy as you will need it in the next steps. 3.4.3 Configure Navigate to your hello_world directory from Step 3.4.1. Start a Project, set ESP32-C2 chip as the target and run the project configuration utility menuconfig. 1 cd ~/esp/hello_world 2 idf.py set-target esp32c2 3 idf.py menuconfig Setting the target with idf.py set-target ESP8684 should be done once, after opening a new project. If the project contains some existing builds and configuration, they will be cleared and initialized. The target may be saved in environment variable to skip this step at all. See Selecting the Target for additional information. If the previous steps have been done correctly, the following menu appears:
Figure 3: Project Configuration - Home Window You are using this menu to set up project specific variables, e.g. Wi-Fi network name and password, the processor speed, etc. Setting up the project with menuconfig may be skipped for hello_word. This example will run with default configuration The colors of the menu could be different in your terminal. You can change the appearance with the option
--style. Please run idf.py menuconfig --helpfor further information. 3.4.4 Build the Project Build the project by running:
1 idf.py build Espressif Systems 10 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 3 Get Started This command will compile the application and all ESP-IDF components, then it will generate the bootloader, partition table, and application binaries. 1 $ idf.py build 2 Running cmake in directory /path/to/hello_world/build 3 Executing cmake -G Ninja --warn-uninitialized /path/to/hello_world... 4 Warn about uninitialized values. 5 -- Found Git: /usr/bin/git (found version 2.17.0) 6 -- Building empty aws_iot component due to configuration 7 -- Component names: ... 8 -- Component paths: ... 9 10 ... (more lines of build system output) 11 12 [527/527] Generating hello_world.bin 13 esptool.py v2.3.1 14 15 Project build complete. To flash, run this command:
16 ../../../components/esptool_py/esptool/esptool.py -p (PORT) -b 921600 17 write_flash --flash_mode dio --flash_size detect --flash_freq 40m 18 0x10000 build/hello_world.bin build 0x1000 build/bootloader/bootloader.bin 0x8000 19 build/partition_table/partition-table.bin 20 or run idf.py -p PORT flash If there are no errors, the build will finish by generating the firmware binary .bin file. 3.4.5 Flash onto the Device Flash the binaries that you just built onto your module by running:
1 idf.py -p PORT [-b BAUD] flash Replace PORT with your ESP8684 boards serial port name from Step: Connect Your Device. You can also change the flasher baud rate by replacing BAUD with the baud rate you need. The default baud rate is 460800. For more information on idf.py arguments, see idf.py. Note:
The option flash automatically builds and flashes the project, so running idf.py build is not necessary. When flashing, you will see the output log similar to the following:
1 ... 2 esptool.py esp32c2 -p /dev/ttyUSB0 -b 460800 --before=default_reset --after=hard_reset 3 write_flash --flash_mode dio --flash_freq 80m --flash_size 2MB 0x0 bootloader/bootloader. bin 4 0x10000 hello_world.bin 0x8000 partition_table/partition-table.bin 5 esptool.py v3.2-dev 6 Serial port /dev/ttyUSB0 7 Connecting.... Espressif Systems 11 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 3 Get Started 8 Chip is ESP32-C2 9 Features: WiFi, BLE 10 Crystal is 40MHz 11 MAC: 7c:df:a1:e0:00:64 12 Uploading stub... 13 Running stub... 14 Stub running... 15 Changing baud rate to 460800 16 Changed. 17 Configuring flash size... 18 Flash will be erased from 0x00000000 to 0x00004fff... 19 Flash will be erased from 0x00010000 to 0x00039fff... 20 Flash will be erased from 0x00008000 to 0x00008fff... 21 Compressed 18896 bytes to 11758... 22 Writing at 0x00000000... (100 %) 23 Wrote 18896 bytes (11758 compressed) at 0x00000000 in 0.5 seconds (effective 279.9 kbit/s)
... 24 Hash of data verified. 25 Compressed 168208 bytes to 88178... 26 Writing at 0x00010000... (16 %) 27 Writing at 0x0001a80f... (33 %) 28 Writing at 0x000201f1... (50 %) 29 Writing at 0x00025dcf... (66 %) 30 Writing at 0x0002d0be... (83 %) 31 Writing at 0x00036c07... (100 %) 32 Wrote 168208 bytes (88178 compressed) at 0x00010000 in 2.4 seconds (effective 569.2 kbit/s
)... 33 Hash of data verified. 34 Compressed 3072 bytes to 103... 35 Writing at 0x00008000... (100 %) 36 Wrote 3072 bytes (103 compressed) at 0x00008000 in 0.1 seconds (effective 478.9 kbit/s)... 37 Hash of data verified. 38 39 Leaving... 40 Hard resetting via RTS pin... 41 Done If there are no issues by the end of the flash process, the board will reboot and start up the hello_world application. 3.4.6 Monitor To check if hello_world is indeed running, type idf.py -p PORT monitor (Do not forget to replace PORT with your serial port name). This command launches the IDF Monitor application:
1 $ idf.py -p /dev/ttyUSB0 monitor 2 Running idf_monitor in directory [...]/esp/hello_world/build 3 Executing python [...]/esp-idf/tools/idf_monitor.py -b 115200 4 [...]/esp/hello_world/build/hello-world.elf... Espressif Systems 12 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 3 Get Started 5 --- idf_monitor on /dev/ttyUSB0 115200 ---
6 --- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
7 ets Jun 8 2016 00:22:57 8 9 rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) 10 ets Jun 8 2016 00:22:57 11 ... After startup and diagnostic logs scroll up, you should see Hello world! printed out by the application. 1 ... 2 Hello world!
3 Restarting in 10 seconds... 4 This is esp32c2 chip with 2 CPU core(s), This is esp32c2 chip with 2 CPU core(s), WiFi/BLE
, 5 silicon revision 0, 2MB external flash 6 Minimum free heap size: 390684 bytes 7 Restarting in 9 seconds... 8 Restarting in 8 seconds... 9 Restarting in 7 seconds... To exit IDF monitor use the shortcut Ctrl+]. Thats all what you need to get started with ESP8684-MINI-1U module! Now you are ready to try some other examples in ESP-IDF, or go right to developing your own applications. Espressif Systems 13 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 4 U.S. FCC Statement 4 U.S. FCC Statement The device complies with KDB 996369 D03 OEM Manual v01. Below are integration instructions for host product manufacturers according to the KDB 996369 D03 OEM Manual v01. List of Applicable FCC Rules FCC Part 15 Subpart C 15.247 Specific Operational Use Conditions The module has WiFi, and BLE functions. Operation Frequency:
WiFi: 2412 ~ 2462 MHz Bluetooth: 2402 ~ 2480 MHz Number of Channel:
WiFi: 11 Bluetooth: 40 Modulation:
WiFi: DSSS; OFDM Bluetooth: GFSK;
Type: sleeve monopole antenna connector Gain: 2.33 dBi Max The module can be used for IoT applications with a maximum 2.33 dBi antenna. The host manufacturer installing this module into their product must ensure that the final composit product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation. The host manufacturer has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Limited Module Procedures Not applicable. The module is a single module and complies with the requirement of FCC Part 15.212. Trace Antenna Designs Not applicable. The module has its own antenna, and does not need a hosts printed board microstrip trace antenna, etc. RF Exposure Considerations The module must be installed in the host equipment such that at least 20cm is maintained between the antenna and users body; and if RF exposure statement or module layout is changed, then the host product manufacturer Espressif Systems 14 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 4 U.S. FCC Statement required to take responsibility of the module through a change in FCC ID or new application. The FCC ID of the module cannot be used on the final product. In these circumstances, the host manufacturer will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Antennas Antenna specification are as follows:
Type: sleeve monopole antenna connector Gain: 2.33 dBi This device is intended only for host manufacturers under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the sleeve monopole antenna(s) that has been originally tested and certified with this module. The antenna must be either permanently attached or employ a unique antenna coupler. As long as the conditions above are met, further transmitter test will not be required. However, the host manufacturer is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Label and Compliance Information Host product manufacturers need to provide a physical or e-label stating Contains FCC ID:
2AC7Z-ESP8684M1U with their finished product. Information on test modes and additional testing requirements Operation Frequency:
WiFi: 2412 ~ 2462 MHz Bluetooth: 2402 ~ 2480 MHz Number of Channel:
WiFi: 11 Bluetooth: 40 Modulation:
WiFi: DSSS; OFDM Bluetooth: GFSK;
Host manufacturer must perform test of radiated and conducted emission and spurious emission, etc., according to the actual test modes for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. Only when all the test results of test modes comply with FCC requirements, then the end product can be sold legally. Espressif Systems 15 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 4 U.S. FCC Statement Additional testing, Part 15 Subpart B compliant The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.247 and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. OEM Integration Instructions This device is intended only for OEM integrators under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with thesleeve monopole antenna(s) that has been originally tested and certified with this module. Espressif Systems 16 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 4 U.S. FCC Statement As long as the conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Validity of Using the Module Certification In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: Contains Transmitter Module FCC ID:
2AC7Z-ESP8684M1U. Espressif Systems 17 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 5 Industry Canada Statement 5 Industry Canada Statement This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
This device may not cause interference; and This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
lappareil ne doit pas produire de brouillage, et lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Dclaration dexposition aux radiations:
Cet quipement est conforme aux limites dexposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. RSS-247 Section 6.4 (5) The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. Lappareil peut interrompre automatiquement la transmission en cas dabsence dinformations transmettre ou de panne oprationnelle. Notez que ceci nest pas destin interdire la transmission dinformations de contrle ou de signalisation ou lutilisation de codes rptitifs lorsque cela est requis par la technologie. This device is intended only for OEM integrators under the following conditions (For module device use):
The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Espressif Systems 18 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 5 Industry Canada Statement Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes (Pour utilisa-
tion de dispositif module):
Lantenne doit tre installe de telle sorte quune distance de 20 cm est respecte entre lantenne et les utilisateurs, et Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur lmetteur ne seront pas ncessaires. Toutefois, lintgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations dordinateur portable ou de certaines co-localisation avec un autre metteur), lautorisation du Canada nest plus considr comme valide et lID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, lintgrateur OEM sera charg de rvaluer le produit final (y compris lmetteur) et lobtention dune autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: 21098-ESP8684M1U. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o lantenne peut tre installe de telle sorte quune distance de 20cm peut tre maintenue entre lantenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec linscription suivante: Contient des IC:
21098-ESP8684M1U. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel dinformation lutilisateur final Lintgrateur OEM doit tre conscient de ne pas fournir des informations lutilisateur final quant la faon dinstaller ou de supprimer ce module RF dans le manuel de lutilisateur du produit final qui intgre ce module. Le Espressif Systems 19 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 5 Industry Canada Statement manuel de lutilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Espressif Systems 20 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 6 Related Documentation and Resources 6 Related Documentation and Resources Related Documentation ESP8684 Series Datasheet Specifications of the ESP8684 hardware. ESP8684 Technical Reference Manual Detailed information on how to use the ESP8684 memory and peripherals. ESP8684 Hardware Design Guidelines Guidelines on how to integrate the ESP8684 into your hardware product. Certificates https://espressif.com/en/support/documents/certificates ESP8684 Product/Process Change Notifications (PCN) https://espressif.com/en/support/documents/pcns?keys=ESP8684 Documentation Updates and Update Notification Subscription https://espressif.com/en/support/download/documents Developer Zone ESP-IDF Programming Guide for ESP8684 Extensive documentation for the ESP-IDF development framework. ESP-IDF and other development frameworks on GitHub. https://github.com/espressif ESP32 BBS Forum Engineer-to-Engineer (E2E) Community for Espressif products where you can post questions, share knowledge, explore ideas, and help solve problems with fellow engineers. https://esp32.com/
The ESP Journal Best Practices, Articles, and Notes from Espressif folks. https://blog.espressif.com/
See the tabs SDKs and Demos, Apps, Tools, AT Firmware. https://espressif.com/en/support/download/sdks-demos Products ESP8684 Series SoCs Browse through all ESP8684 SoCs. https://espressif.com/en/products/socs?id=ESP8684 ESP8684 Series Modules Browse through all ESP8684-based modules. https://espressif.com/en/products/modules?id=ESP8684 ESP8684 Series DevKits Browse through all ESP8684-based devkits. https://espressif.com/en/products/devkits?id=ESP8684 ESP Product Selector Find an Espressif hardware product suitable for your needs by comparing or applying filters. https://products.espressif.com/#/product-selector?language=en Contact Us See the tabs Sales Questions, Technical Enquiries, Circuit Schematic & PCB Design Review, Get Samples
(Online stores), Become Our Supplier, Comments & Suggestions. https://espressif.com/en/contact-us/sales-questions Espressif Systems 21 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 Revision History Revision History Date Version Release notes 2023-07-25 v0.5 Preliminary release Espressif Systems 22 Submit Documentation Feedback ESP8684-MINI-1U User Manual v0.5 Disclaimer and Copyright Notice Information in this document, including URL references, is subject to change without notice. ALL THIRD PARTYS INFORMATION IN THIS DOCUMENT IS PROVIDED AS IS WITH NO WARRANTIES TO ITS AUTHENTICITY AND ACCURACY. NO WARRANTY IS PROVIDED TO THIS DOCUMENT FOR ITS MERCHANTABILITY, NON-
INFRINGEMENT, FITNESS FOR ANY PARTICULAR PURPOSE, NOR DOES ANY WARRANTY OTHERWISE ARISING OUT OF ANY PROPOSAL, SPECIFICATION OR SAMPLE. All liability, including liability for infringement of any proprietary rights, relating to use of information in this document is disclaimed. No licenses express or implied, by estoppel or otherwise, to any intellectual property rights are granted herein. The Wi-Fi Alliance Member logo is a trademark of the Wi-Fi Alliance. The Bluetooth logo is a registered trademark of Bluetooth SIG. www.espressif.com All trade names, trademarks and registered trademarks mentioned in this document are property of their respective owners, and are hereby acknowledged. Copyright 2023 Espressif Systems (Shanghai) Co., Ltd. All rights reserved.