FCC ID: ZMOFM101RGL LTE Module

FIDCCON ois) FM101R-GL 12 9/d CA DB [Goes ANATEL:XXXXXXXXXX C &S XXX CMIIT ID:XXXXXXXXXX SI 7 0000001 1C:21374- FM101RGL XXXXXXXXXXXXX >

FCC ID:ZMOFM101RGL BERS, BSL S/NDQOOOOOOOXX Fibocom Wireless Inc. e IMEI:XXXXXXXXXXXXXXX Made in China Ww eUlyD ul epeW XXXXXXXXXXXXXAX: SIN OU] SSBjeuIM WOSOq!4 XXXXXXXXXX'N/S BARE iaPRR He ) JOYLOLWAOWZ:dl 904 XXXXXXXXXXXXX TOULOLWSA -PZELZ:91 ron 4 FD XXXXXXXXXX:CI LW XOOOCKHK XXXXXXXXXX: TALVNV a) YW ) Sy ra 79-ULOLWS WOD,0QI4

Modular Approval Request FCC ID: ZMOFM101RGL Items to be covered by Single modular transmitters. 1. The modular transmitter must have its own RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or overmodulation. 3. The modular transmitter must have its own power supply regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). 5. The modular transmitter must be tested in a standalone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID: XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF_734_02 04 April 16 Answer from applicant Yes The EUT provides the RF shielding. See EUT photo. Yes The EUT has its buffered modulation. Data to the modulation circuit is buffered as described in the operational description provided with the application. Yes The EUT has its own power supply regulation, please see the Schematic Diagram. Yes The EUT meets the FCC/ISED antenna requirements; unique antenna connector and photo of antenna are shown in the test report. Yes The EUT was tested with a test board, Please see test report and setup photo Yes The FCC ID is ZMOFM101RGL Yes The EUT is compliant with all applicable FCC rules. Details instructions for maintaining compliance are give in the User Manual. Yes RF_734_02 04 April 16 The EUT complies with RF exposure requirement. RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: A limited modular approval (LMA) may be granted for single modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): Patrick Ma Signature:

Date: 2023/08/02