iRUGGY G10 Mobile Tablet User Manual Version 1.5 April 25, 2017 2 G10 User Manual Copyright Copyright 2018 All Rights Reserved Manual Version 1.5 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of the manufacturer. Trademark The material in this manual is subject to change without notice. Bluetooth is a registered trademark of Bluetooth SIG. Microsoft, and Windows are either registered trademarks or trademarks of Microsoft Corporation. All other product or service names are the property of their respective owners. Safety Regulatory Information Caution: Only use approved and UL Listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source. Power Supply Use only the approved power supply shipped with the unit. Use of alternative power supply will invalidate any approval given to this device and may be dangerous. Warning for Use of Wireless Devices Please observe all warning notices with regard to the usage of wireless devices. Potentially Hazardous Atmospheres You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Confidential and Proprietary Information G10 User Manual 3 Safety in Aircraft Switch off your wireless device whenever you are instructed to do so by airport or airline staff. Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research. Persons with Pacemakers Persons with Pacemakers should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON and hence they should not carry the device in a breast pocket. They should use the ear furthest from the pacemaker to minimize the potential for interference. If you have any reason to suspect that interference is taking place, turn OFF your device. Hearing Aids The wireless device may interfere with some hearing aids. In the event of interference you may want to consult your hearing aid supplier to discuss solutions. Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device. FCC/EU RF Exposure Guidelines FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC SAR exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Confidential and Proprietary Information G10 User Manual 4 Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE Marking and European Economic Area The use of 2.4GHz RLAN's, for use through the EEA, have the following restrictions:
Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -
2.4835 GHz In France, outside usage is restricted to 2.4 - 2.454 GHz. Italy requires a user license for outside usage. Bluetooth Wireless Technology for use through the EEA has the following restrictions:
-
-
-
Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -
2.4835 GHz. In France, outside usage is restricted to 10mW EIRP. Italy requires a user license for outside usage. Battery Information Our rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and severe drops. When batteries are stored over six (6) months, some irreversible deterioration in overall battery quality may occur. Store batteries discharged in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts and electrolyte leakage. When storing batteries for one year or longer, they should be charged and discharged at least once a year. If an electrolyte leakage is observed, avoid any contact with affected area and properly dispose of the battery. Batteries must be charged within the 0 to +35C (32 to 95 F) ambient temperature range. Replace the battery when a significant loss of run time is detected. Battery Caution There is a risk of explosion if the battery is replaced by an incorrect type. Dispose of used battery according to the local disposal instructions. Waste Electrical and Electronic Equipment (WEEE) For EU Customers: All products at the end of their life must be returned to the reseller for recycling. Confidential and Proprietary Information G10 User Manual Revision Table 5 Version Date Changes 1.3 1.4 1.5 Nov 16, 2016 Initial release Jan 10, 2017 Updated battery level indicator status definition in 4.6.2 Apr 24, 2018 Added stylus, mPOS brackets to 1.2 Accessories; removed references to rotating hand strap (discontinued); aligned 2.3 Specification with current datasheet; updated instruction for installing mPOS brackets in 5.3; added caution on placing tablet correctly in the POS dock in 6.3 Confidential and Proprietary Information Table of Contents 1 Unpacking the unit ................................................................................................................................ 8 1.1 1.2 Standard items .............................................................................................................................. 8 Accessories .................................................................................................................................... 8 2 Hardware Overview ............................................................................................................................ 11 2.1 2.2 2.3 Features ...................................................................................................................................... 11 System Overview......................................................................................................................... 12 Specifications .............................................................................................................................. 13 3 4 Product Labelling ................................................................................................................................ 14 Basic Operation ................................................................................................................................... 15 4.1 Power On/Off Button .................................................................................................................. 15 4.1.1 4.1.2 4.1.3 Turning on the Unit ............................................................................................................. 15 Turning off the Unit ............................................................................................................. 15 Turning off the Display Backlight ........................................................................................ 15 4.2 4.3 4.4 4.5 4.6 in4Touch Touch Mode Control Button .................................................................................... 15 Adjusting Screen Brightness........................................................................................................ 16 Adjusting System Volume ........................................................................................................... 16 Programmable Function Key ....................................................................................................... 16 Charging the Battery ................................................................................................................... 16 4.6.1 4.6.2 4.6.3 Charging via Cable to AC Adapter ....................................................................................... 16 Battery Level Indicator on Tablet ........................................................................................ 17 Battery Charge Level Indicator on Battery .......................................................................... 17 4.7 Replacing the Battery .................................................................................................................. 18 4.7.1 4.7.2 Removing the Battery ......................................................................................................... 18 Installing the Battery ........................................................................................................... 18 5 Installation and Setup ......................................................................................................................... 19 5.1 5.2 5.3 5.4 5.5 System Software ......................................................................................................................... 19 Attaching the Hand Strap ............................................................................................................ 20 Installing a 3G or microSD Card .................................................................................................. 20 Installing ADD-f(x) Modules ..................................................................................................... 21 Attaching an mPOS Integration Bracket ..................................................................................... 22 6 Using the G10 POS Docking Station .................................................................................................... 23 G10 User Manual 7 6.1 6.2 6.3 6.4 6.5 Connecting to Power ................................................................................................................... 23 Connecting to Network and Peripherals ..................................................................................... 23 Placing the Tablet in the Dock .................................................................................................... 24 Installing the Customer Display .................................................................................................. 25 Installing a third-party payment device ...................................................................................... 26 7 Software Configuration ....................................................................................................................... 27 Appendix A: Supported Bar Code Symbologies ......................................................................................... 28 Confidential and Proprietary Information G10 User Manual 1 Unpacking the unit The following items may be shipped with each unit. 1.1 Standard items Tablet Standard Hand Strap 1.2 Accessories 8 AC Adapter Quick Start Guide 1D/2D Barcode Scanner ADD-f(x) Module Fingerprint Reader ADD-f(x) Module Confidential and Proprietary Information 9 G10 User Manual HF RFID Reader ADD-f(x) Module G10 mPOS Integration Bracket Mounting Plate mPOS Integration Bracket for Verifone e355 MSR / Smart Card Combo ADD-f(x) Module mPOS Integration Bracket for Ingenico iCMP mPOS Integration Bracket for Miura M010 G10 POS Docking Station G10 POS Dock mPOS Bracket Mount Confidential and Proprietary Information G10 User Manual 10 POS Dock Customer Display 2m Tip Stylus Confidential and Proprietary Information 11 Front View G10 User Manual 2 Hardware Overview 2.1 Features 1 2MP webcam 2 Programmable capacitive function key 3 Battery status indicator 4 Ambient light sensor 5 Touch screen 6 Kensington lock slot 7 ADD-f(x) expansion module bays (3) 8 5MP AF camera with LED flash 9 Battery 10 Battery release latch 11 Speakers (2) 12 DC-in 13 Docking connector 14 Access cover for 3G and microSD slots 15 Stylus port 16 Access cover for USB 2.0, Micro USB
(OTG) and Micro HDMI port 17 Location of internal NFC reader 18 Audio jack 19 20 Power On/Off 21 Microphone in4Touch touch mode control Back View Confidential and Proprietary Information G10 User Manual 2.2 System Overview 12 Confidential and Proprietary Information G10 User Manual 2.3 Specifications Touch Display Processor Operating systems Memory / Storage Camera Expansion I/O ports Audio Communications Power Supply Environmental 13 10.1 (1920 x 1200 resolution) projected capacitive multi-touch display User-selectable touch mode for Hand, Glove, Stylus or Rain Programmable capacitive function key on front-bezel Intel Quad-Core 1.83GHz Windows 10 IoT Enterprise for Tablet Android 4.4.4 2GB DDR3L memory / 64GB storage
(Android Model: 32GB) microSDXC socket for expansion 5MP autofocus rear camera with LED flash 2MP front-facing camera USB 2.0 Micro HDMI Micro USB (supports OTG) Additional peripheral I/O available through optional POS Docking Station 1W stereo speakers Audio jack Microphone WLAN 802.11 ac Bluetooth 4.0 + LE (class 2) NFC contactless card reader 3G data and dedicated GPS (factory option) 3.7V 8000 mAh battery, hot swappable* with up to 8 hours per charge DC-in, with external AC adapter (Output 5V DV, 4A, Input 100-240VAC, 50/60Hz) for charging IP65 rated protection from liquid and dust ingress Designed to MIL-STD-810G 1.2M drop specification Operating temperature: -10C ~ 50C (14F ~ 122F);
max. 35C (95F) when charging battery Storage temperature: -20C ~ 70C (-4F ~ 158F) Humidity: 90% RH non-condensing Dimensions (W x H x D) Weight (with Battery) ADD-f(x) modules Optional accessories 227 x 185 x 20 mm (10.9 x 7.3 x 0.78) 997g (2.19 lbs) 1D/2D optical barcode scanner Fingerprint readers LF, HF, UHF RFID readers Smart card reader (EMV Level 1 and 2 certified) and 3 track encrypted MSR Rear mounting bracket for mPOS devices LAN and COM I/O Module POS docking station (1x LAN, 3x USB 2.0, 1x COM, 1x CD) VESA charging mount Vehicle charging mount 2m tip stylus 1 1GB=1 billion bytes; actual formatted capacity will be less 2 Subject to service providers broadband subscription and coverage area; additional charges may apply 3 Standard configuration with Intel Z3735F CPU, 2GB memory and 64GB eMMC tested using PCMark 8 battery life benchmark. Results may be used for product comparison and may vary under different situations including hardware configuration, software, operating conditions, power management settings and other factors. Battery life will decrease with time and use 4 Weight shown represents base configuration with battery, excluding any optional accessories 5 Accessories may vary depending on your configuration. Accessories are sold separately
*Hot swappable feature is only available with 3G data communication and dedicated GPS option. Confidential and Proprietary Information G10 User Manual 14 3 Product Labelling Safety certification and other compliance labels may be found on the inside of the battery compartment, along with product serial number and Windows license sticker. See section on Removing the Battery for instructions on removing the battery module to view this information. All tablets are labelled with a unique serial number. This number is important in tracking units through production and shipment and may be required for servicing the product under the warranty. Product certification labels Confidential and Proprietary Information 15 G10 User Manual 4 Basic Operation 4.1 Power On/Off Button Power On/Off button in4Touch touch mode control button 4.1.1 Turning on the Unit Press and hold the power button 2 seconds on to turn on the system. You will feel a vibration the moment the system powers on. NOTE: The tablet must be docked, plugged into AC or battery charged before turning on the unit for the first time. 4.1.2 Turning off the Unit The unit should be shut down normally via the operating system. The manually power off the unit, press and hold the power button 5 seconds. 4.1.3 Turning off the Display Backlight System settings can be used to turn off the backlight automatically for power savings when the system is idle. When the unit is powered on, pressing the power button momentarily will turn off and on the backlight unless these settings are changed. in4Touch Touch Mode Control Button 4.2 Press and hold the in4Touch button to cycle through graphic icons displayed on screen representing each of 4 supported touch operation modes. Once the graphic icon is highlighted, release the button to activate the touch mode represented by that icon. Hand Supports normal touch operation using a bare finger. Glove Enables touch operation when the user is wearing gloves. Stylus Restricts input to stylus, ignoring finger or palm contact. Must be used with the G10 Rain stylus connected to the stylus port on the tablet. Supports touch operation using bare finger while reducing interference from random drops of liquid on the screen. Confidential and Proprietary Information G10 User Manual 16 4.3 Adjusting Screen Brightness Windows display settings allow screen brightness to be set manually or adjusted automatically for power savings or for comfort under different lighting conditions. There are 4 manual settings: 100%, 75%, 50% and 25%. Factory default setting for the display is fixed at 100% brightness. An ambient light sensor located on the front of the display may be used to sense and reduce the brightness level for comfort in low light environments. This feature is disabled at the factory but can be enabled through system software settings. 4.4 Adjusting System Volume Volume levels on the integrated dual stereo speakers and devices connected through the audio jack must be set manually through Windows or Android system software settings. 4.5 Programmable Function Key The capacitive button on the top right of the tablet display is activated by touch. For Windows and Android models, this button is pre-programmed in the factory as Windows or Home key, but the button may be re-programmed by the user to open applications or access specific functions. For information on re-programming this key, contact your iRuggy Systems authorized distributor or reseller. 4.6 Charging the Battery The G10 Mobile Tablet is equipped with an interchangeable 8000mAH battery module supporting up to 8 hours per charge depending on usage. 4.6.1 Charging via Cable to AC Adapter The battery may be charged by connecting the supplied AC power adaptor directly to the DC-in connector located on the bottom of the tablet. Push the protective rubber seal aside and plug the cable directly into the connector. Then plug the adaptor directly into the AC outlet. Confidential and Proprietary Information G10 User Manual 17 4.6.2 Battery Level Indicator on Tablet A battery level indicator LED on the front of the tablet signals charge status:
Battery charge level at 90% or higher (Tablet is plugged in or placed in dock) Battery is charging (Tablet is plugged in or placed in dock) GREEN ORANGE RED/Flashing Battery level below 15%
Battery level below 10%
RED 4.6.3 Battery Charge Level Indicator on Battery With the battery module removed from the unit, press the icon shown above. The row of LEDs will light up for 3-4 seconds indicating battery charge level as follows:
No charge (No LEDs lit)
< 10% charged (Single flashing LED) 11-24% charged (1 LED on) 25-49% charged (2 LEDs on) 50-74% charged (3 LEDs on) 75-100% charged (All LEDS on) Confidential and Proprietary Information G10 User Manual 4.7 Replacing the Battery 4.7.1 Removing the Battery 18 Unless the tablet is equipped with a bridge battery supplied on 3G models, always power down the system first. Unplug the AC cable if connected directly to the DC-in port on the tablet. Place the tablet face down on a flat surface. Next, slide the latch down as shown to unlock and release the batter module so it can be lifted out of the unit. If the system is equipped with the bridge battery, the system will automatically enter Connect Standby Mode and screen backlight will turn off. The front battery level indicator LED will flash and system will beep every 3 seconds for the first 3 minutes. After 3 minutes, the LED will flash and beep will sound every half second. System will automatically shut down at 4 minutes. 4.7.2 Installing the Battery Angle the battery module so that the left side with exposed connector pins is inserted first into the battery compartment. The press into place and slide the latch upward to lock the battery module into position. Confidential and Proprietary Information G10 User Manual 19 5 Installation and Setup 5.1 System Software System is factory-installed with the supported Windows or Android operating system and required drivers for all device options, whether or not device is installed on the unit when shipped. No additional software or device drivers must be installed to begin using the system. On initial bootup of a system loaded with Windows, the Windows activation screen will show and prompt the user through the activation process. See section on Software Configuration for more information on drivers supplied with the system. Confidential and Proprietary Information G10 User Manual 5.2 Attaching the Hand Strap 20 Use of the standard hand strap shipped with the tablet is optional. Depending on the situation, the user may attach the hand strap between anchor points across the top or either side of the tablet. To attach the strap to the tablet, thread both ends of the strap into an anchor point, fold back and tighten in the plastic buckle. Any excess can be tucked into the sleeve handle at the center of the strap. Installing a 3G or microSD Card 5.3 The user may install a user-supplied SDXC or compatible microSD card on the unit to load or save files, or expand working data storage capacity. On select tablet models with support for 3G data communication, a separate slot is available for installing a user-supplied 3G Micro SIM card. To install either type of card, first power down the system. Both lots are accessed by removing the two screws securing a protective, watertight seal located on the bottom of the tablet. Orient either card so that the gold contact edge faces down towards the front of the tablet. Slide the card in until it clicks in place. To remove the card, press the outer edge to click and release the card. Confidential and Proprietary Information G10 User Manual 21 Installing ADD-f(x) Modules 5.4 Optional ADD-f(x) modules are available to expand tablet functionality. To install any module, first power down the system. Locate the three universal expansion bays on the top, back side of the tablet. Depending on the number and size of the modules selected, one or all three bays may be used to install 1, 2 or up to 3 ADD-f(x) modules. Remove the two screws and lift off the plastic cover covering each bay. This cover may be saved or discarded. Slide the module in place and fasten in place with the four screws provided. Confidential and Proprietary Information G10 User Manual 22 5.5 Attaching an mPOS Integration Bracket Custom brackets are available for on-tablet integration of third-party mobile point-of-sale (mPOS) payment devices. To attach the bracket, place the tablet face down. Position the metal universal mounting plate over the battery module as shown and attach with the four screws provided (you may need to first remove and discard cosmetic rubber covers placed over the screw holes). iRuggy offers brackets designed for the Ingenico iCMP, Verifone e355 and Miura M010 mPOS devices. To install, attach the bracket to the universal mounting plate and secure with either two or four screws as provided. Example above shows the Ingenico iCMP bracket. Once the bracket is attached, the mPOS device may slide in from the top or bottom, depending on design. The charging port on the mPOS will remain accessible to allow connection of a charging cable
(supplied by the mPOS device vendor) without removing the device from the tablet. Confidential and Proprietary Information G10 User Manual 23 6 Using the G10 POS Docking Station An optional countertop mount is available to allow the G10 tablet to be operated at different angles while docked for charging, LAN communication and connection with peripherals. The docking station also supports optional mounting of a customer display or third-party payment terminal. 6.1 Connecting to Power Before the docking station can be used to charge the tablet or connect to peripherals, the dock must be connected to AC power via the 19V/65W AC adaptor shipped with the POS Dock. Locate the DC-in connector on the dock and plug in the power cable from the AC adaptor. 6.2 Connecting to Network and Peripherals Disconnect the power cable from the docking station. Plug network or peripheral cables into available ports located in the base:
RJ45 10/100 Ethernet LAN Cash drawer port, 12V or 24V selectable through jumper settings (default 24V) One RJ48 RS-232 port, 0V, 5V or 12V selectable through jumper settings (default 0V) Three 5V USB 2.0 ports Confidential and Proprietary Information G10 User Manual 6.3 Placing the Tablet in the Dock 24 The tablet may be placed on the dock either powered on or off. NOTE: When placing the tablet on the dock, take care to locate the extension on the back center of the tablet and make sure this slides over and covers the tab on the dock. If this tab is not engaged as shown below, the docking connection will be loose and the tablet may not charge or connect to LAN or peripherals. Extension on tablet Tab on POS Dock Open position Locked position There is a latching mechanism to secure the tablet in the dock, accessed on the back of the mount. Before placing the tablet in the dock, check to make sure the latch is in the open position. When removing the tablet from the dock, you may encounter some resistance as there is a strong magnet which helps server to keep the electrical contact points tightly aligned during operation. Confidential and Proprietary Information G10 User Manual 25 Installing the Customer Display 6.4 An optional 2 line x 20 graphic LCD customer display may be mounted on the back of the docking station. Contact your iRuggy Systems or authorized sales representative for a copy of the separate user guide and OPOS driver for the customer display option. To install the customer display, remove the single screw securing a cover over the rear mount area and discard. Thread the customer display cable through the opening and fasten the display mount into place with the four screws provided. Connect the host end of the cable to any of the available USB ports. Confidential and Proprietary Information G10 User Manual 26 Installing a third-party payment device 6.5 An optional mounting post is available to attach a third-party payment device on the back of the docking station. The post is compatible with device-specific mPOS brackets supplied by iRuggy Systems. To install the device mount, remove the screw and discard the blanking cover over the rear mount access. Attach the post to the base with the four screws provided before attaching the iRuggy Systems mPOS bracket. Confidential and Proprietary Information G10 User Manual 27 7 Software Configuration All Windows or Android software and device drivers required to operate the tablet with any standard or optional features or accessories are pre-installed at the factory. There is no need to download and install additional driver software, even for ADD-f(x) accessories shipped separately. Contact your iRuggy Systems authorized distributor or reseller for technical information required for software integration or specific device configuration. 1D/2D Barcode Scanner ADD-f(x) module: See Appendix A for supported bar code symbologies HF RFID Reader ADD-f(x) module: Following tags may be read at maximum range 25-30 mm:
Mifare_UltraLight Mifare_One(S50) Mifare_One(S70) Mifare_Pro(X) Mifare_DESFire The integrated NFC reader on the tablet supports the following tags:
NXP Mifare Ultralight NXP DESFire Sony FeliCa Broadcom Topaz Confidential and Proprietary Information G10 User Manual 28 Appendix A: Supported Bar Code Symbologies Below bar codes types are supported by the optional 1D/2D Barcode Scanner ADD-f(x) module:
Aztec Code Codabar Codablock F Code 11 Code 32(PARAF) Code 128 Code 2 of 5 Code 39 Code 93 Data Matrix EAN/JAN-13 EAN/JAN 8 EAN-UCC Composite Codes EAN-UCC Emulation IATA Code 2 of 5 Interleaved 2 of 5 Matrix 2 of 5 MaxiCode MicroPDF417 MSI, PDF417 QR Code GS1 DataBar TCIF Linked Code 39 UPC-A UPC E RSS Expanded RSS Limited RSS-14 Chinese Sensible (Han Xin) code Codablock A UPC-A/EAN-13 with Extended Coupon Code Coupon GS1 GS1codebar Confidential and Proprietary Information
