FCC ID: IPH-04247 Digital Transceiver

IMPORTANT SAFETY AND PRODUCT INFORMATION WARNING Failure to heed the following warnings could result in an accident or collision resulting in death or serious injury. Distraction Warning This device is intended to enhance the situational awareness when used properly. If used improperly, you could become distracted by the display, which could lead to an accident causing serious personal injury or death. Only access the information displayed on the device with a glance. Always maintain awareness of your surroundings and do not stare at the display or become distracted by the display. Focusing on the display could prevent you from avoiding obstacles or hazards. Battery Warnings A lithium-ion battery is used in this device. If these guidelines are not followed, batteries may experience a shortened life span or may 1 present a risk of damage to the device, fire, chemical burn, electrolyte leak, and/or injury. Do not disassemble, modify, remanufacture, puncture or damage the device or batteries. Do not remove or attempt to remove the non-

user-replaceable battery. Do not expose the device or batteries to fire, explosion, or other hazard. Do not place in high temperature environments, such as a clothes dryer. Health Warning Always consult your physician before beginning or modifying any exercise program. Device Warnings Do not immerse the device or batteries in water or other liquids. Do not leave the device exposed to a heat source or in a high-temperature location, such as in the sun in an unattended vehicle. To prevent the possibility of damage, remove the device from the vehicle or store it out of direct sunlight, such as in the glove box. Do not use a power cable, data cable and/or power adapter that is not approved or supplied by Garmin. Warnings Always use your best judgement, and operate in a safe manner. Make sure your hardware are properly maintained and that all parts are correctly installed. Safety and Tracking Warning The assistance feature allows you to send your location to an emergency contact. This is a supplemental feature and should not be relied upon as a primary method to obtain emergency assistance. The app does 2 not contact emergency services on your behalf. The incident detection feature is only available while you are tracking certain outdoor activities on your Garmin device. For more information, see the device owner's manual. Off-Road Navigation Warnings If your Garmin device is able to suggest off-

road routes for various outdoor activities, such as biking, hiking, and all-terrain vehicles, follow these guidelines to ensure safe off-road navigation. Always use your best judgment and exercise common sense when making off-road navigational decisions. The Garmin device is designed to provide route suggestions only. It is not a replacement for attentiveness and proper preparation for outdoor activities. Do not follow the route suggestions if they suggest an illegal course or would put you in an unsafe situation. Always carefully compare information displayed on the device to all available navigation sources, including trail signs, trail conditions, weather conditions, and other factors that may affect safety while navigating. For safety, always resolve any discrepancies before continuing navigation, and defer to posted signs and conditions. Always be mindful of the effects of the environment and the inherent risks of the activity before embarking on off-road activities, especially the impact that weather and weather-related trail conditions can have on the safety of your activity. Ensure that you have the proper gear and supplies for your activity before navigating along unfamiliar paths and trails. 3 NOTICE Failure to heed the following notices could result in personal or property damage, or negatively impact the device functionality. Battery Notice Contact your local waste disposal department to dispose of the device/batteries in accordance with applicable local laws and regulations. Legal Restrictions IT IS THE USER'S RESPONSIBILITY TO MOUNT AND OPERATE THE DEVICE IN COMPLIANCE WITH ALL APPLICABLE LAWS AND ORDINANCES. Garmin does not assume any responsibility for any fines, penalties, or damages that may be incurred as a result of any state or local law or ordinance relating to the use of your Garmin device. Legal Notice I It is your responsibility to know and comply with applicable laws and rights in your jurisdiction. Specifications Operating temperature range: From -15 to 45C (from 5 Charging temperature range: From 0 to 45C (from 32 Storage temperature range: From -20 to 45C (from -4 to 113F) to 113F) to 113F) Wireless frequencies: 2.4 GHz @ 7 dBm maximum; 24 GHz @ -11.3 dBm maximum SAR: 0.10 W/kg torso, 0.10 W/kg limb Product Environmental Programs Information about the Garmin product recycling program and WEEE, RoHS, REACH, and other compliance programs can be found at www.garmin.com/aboutGarmin

/environment. 4 Declaration of Conformity Hereby, Garmin declares that this product is in compliance with the Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.garmin.com/compliance. UK Declaration of Conformity Hereby, Garmin declares that this product is in compliance with the relevant statutory requirements. The full text of the declaration of conformity is available at the following internet address: www.garmin.com/compliance. Innovation, Science and Economic Development Canada Compliance This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency Radiation Exposure This device is a portable transmitter and receiver that uses an internal antenna to send and receive low levels of radio frequency (RF) energy for data communications. The device emits RF energy below the published limits when operating in its maximum output power mode and when used with Garmin authorized accessories. The device should not be used in other configurations. This device must not be co-located or operated in conjunction with any other transmitter or antenna. FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

5 Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This product does not contain any user-serviceable parts. Repairs should only be made by an authorized Garmin service center. Unauthorized repairs or modifications could result in permanent damage to the equipment, and void your warranty and your authority to operate this device under Part 15 regulations. Software License Agreement BY USING THE DEVICE, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY. Garmin Ltd. and its subsidiaries (Garmin) grant you a limited license to use the software embedded in this device (the Software) in binary executable form in the normal operation of the product. Title, ownership rights, and intellectual property rights in and to the Software remain in Garmin and/or its third-party providers. You acknowledge that the Software is the property of Garmin and/or its third-party providers and is protected under the United States of America copyright laws and international copyright treaties. You further acknowledge that the structure, organization, and code of the Software, for which source code is not provided, are valuable trade secrets of Garmin and/or its third-party providers and that the Software in source code form remains a valuable trade secret of Garmin and/or its third-party providers. You agree not to decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to human readable form the Software or any part thereof or create any derivative works based on the Software. You agree not to export or re-export the Software to any country in violation of the export control laws of the United States of America or the export control laws of any other applicable country. Third-Party Software License Agreement This product may include software distributed by Texas Instrumentsunder the following license: Copyright 2014, Texas Instruments Incorporated. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 6 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. Neither the name of Texas Instruments Incorporated nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Third-Party Software Notices ARM CMSIS Deliverables: This product may contain the ARM CMSIS deliverables (https://github.com/ARM-

software/CMSIS/tree/master/CMSIS), distributed under the 3-Clause BSD License (https://github.com/ARM-

software/CMSIS/blob/master/CMSIS/DSP_Lib/license.txt) and subject to the End User License Agreement for the CMSIS Deliverables (http://www.keil.com/Content/eula

/cmsiseula.html) and distributed under the STMicroelectronics Software Package License Agreement

- SLA0048 (http://www.st.com/SLA0048) and distributed by Nordic Semiconductor ASA. Copyright 2009-2015 ARM Limited. All rights reserved. STM32Cube MCU Packages: This product may contain STM32Cube MCU Packages distributed under the 3-Clause BSD License (https://opensource.org/licenses/BSD-3-

Clause) and subject to the Software Package License Agreement (www.st.com/SLA0048). Copyright 2017 STMicroelectronics. FatFS: This product may contain FatFS software. Copyright 2017, ChaN. All rights reserved. mbed TLS: This product may contain the mbed TLS software (https://github.com/ARMmbed/mbedtls), distributed under the Apache 2.0 License 7

(http://www.apache.org/licenses/LICENSE-2.0). Portions Copyright 2006-2015 ARM Limited. All rights reserved. XySSL 0.9: This product may contain XySSL 0.9 software

(https://github.com/axic/tropicssl/tree

/e3be34d1d37153105a3707fe53cc0a3c6bf8ed0c), distributed under the following 3-Clause BDS License

(https://github.com/axic/tropicssl/blob

/e3be34d1d37153105a3707fe53cc0a3c6bf8ed0c/BSD

.txt). Copyright 2006-2008, Christophe Devine. All rights reserved. ANT+ Shared Source License: This product may include software that is subject to the ANT+ Shared Source License (www.thisisant.com/swlicenses). Copyright Garmin Canada Inc. 2010. All rights reserved. Limited Warranty THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER LEGAL RIGHTS, WHICH VARY FROM STATE TO STATE (OR BY COUNTRY OR PROVINCE). GARMIN DOES NOT EXCLUDE, LIMIT OR SUSPEND OTHER LEGAL RIGHTS YOU MAY HAVE UNDER THE LAWS OF YOUR STATE (OR COUNTRY OR PROVINCE). FOR A FULL UNDERSTANDING OF YOUR RIGHTS YOU SHOULD CONSULT THE LAWS OF YOUR STATE, COUNTRY OR PROVINCE. Non-aviation products are warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will, at its sole option, repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. This Limited Warranty does not apply to: (i) cosmetic damage, such as scratches, nicks and dents; (ii) consumable parts, such as batteries, unless product damage has occurred due to a defect in materials or workmanship; (iii) damage caused by accident, abuse, misuse, water, flood, fire, or other acts of nature or external causes; (iv) damage caused by service performed by anyone who is not an authorized service provider of Garmin; (v) damage to a product that has been modified or altered without the written permission of Garmin, or (vi) damage to a product that has been connected to power and/or data cables that are not supplied by Garmin. In addition, Garmin reserves the right to refuse warranty claims against products or services that are obtained and/or used in contravention of the laws of any country. Garmin products are intended to be used only as an aid and must not be used for any purpose requiring precise measurement of direction, distance, location or topography. For navigation products, Garmin makes no 8 warranty as to the accuracy or completeness of the map data. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE WARRANTIES AND REMEDIES CONTAINED IN THIS LIMITED WARRANTY ARE EXCLUSIVE AND IN LIEU OF, AND GARMIN EXPRESSLY DISCLAIMS, ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY REMEDY OR OTHERWISE. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER LEGAL RIGHTS, WHICH VARY FROM STATE TO STATE AND FROM COUNTRY TO COUNTRY. IF IMPLIED WARRANTIES CANNOT BE DISCLAIMED UNDER THE LAWS OF YOUR STATE OR COUNTRY, THEN SUCH WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY. SOME STATES (AND COUNTRIES AND PROVINCES) DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. IN NO EVENT SHALL GARMIN BE LIABLE IN A CLAIM FOR BREACH OF WARRANTY FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. SOME STATES (AND COUNTRIES AND PROVINCES) DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. If during the warranty period you submit a claim for warranty service in accordance with this Limited Warranty, then Garmin will, at its option: (i) repair the device using new parts or previously used parts that satisfy Garmin's quality standards, (ii) replace the device with a new device or a refurbished device that meets Garmin's quality standards, or (iii) exchange the device for a full refund of your purchase price. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. Repaired or replaced devices have a 90 day warranty. If the unit sent in is still under its original warranty, then the new warranty is 90 days or to the end of the original 1 year warranty, whichever is longer. Before seeking warranty service, please access and review the online help resources available on support.garmin.com. If your device is still not functioning properly after making use of these resources, contact a Garmin Authorized service facility in the original country of purchase or follow the instructions on 9 support.garmin.com to obtain warranty service. If you are in the United States, you can also call 1-800-800-1020. If you seek warranty service outside of the original country of purchase, Garmin cannot guarantee that the parts and products needed to repair or replace your product will be available due to differences in product offerings and applicable standards, laws and regulations. In that case, Garmin may, in its sole discretion and subject to applicable laws, repair or replace your product with comparable Garmin products and parts, or require you to ship your product to a Garmin Authorized service facility in the country of original purchase or to a Garmin Authorized service facility in another country that can service your product, in which case you will be responsible for complying with all applicable import and export laws and regulations and for paying all custom duties, V.A.T., shipping fees and other associated taxes and charges. In some cases, Garmin and its dealers may be unable to service your product in a country outside of the original country of purchase or return a repaired or replaced product to you in that country due to applicable standards, laws or regulations in that country. Online Auction Purchases: Online auction confirmations are not accepted for warranty verification. To obtain warranty service, an original or copy of the sales receipt from the original retailer is required. Garmin will not replace missing components from any package purchased through an online auction. International Purchases: A separate warranty may be provided by international distributors for devices purchased outside the United States depending on the country. If applicable, this warranty is provided by the local in-country distributor and this distributor provides local service for your device. Distributor warranties are only valid in the area of intended distribution. Australian Purchases: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits under our Limited Warranty are in addition to other rights and remedies under applicable law in relation to the products. Garmin Australasia, 30 Clay Place, Eastern Creek, NSW 2766, Australia. Phone: 1800 235 822. 10 Limited Warranty The Garmin standard limited warranty applies to this accessory. For more information, go to www.garmin.com

/support/warranty. 11 2022 Garmin Ltd. or its subsidiaries Printed in Taiwan January 2022 190-02225-92

February 3, 2022 To:

Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 USA RE: Confidentiality Request regarding application for certification of FCC ID: IPH-04247 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request permanent confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Operation Description Schematic Diagram File Name Exhibit 12 Block Diagram.pdf Exhibit 14 Operation Description.pdf Exhibit 15 Schematic Diagram.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below for 180 days:

File Name Exhibit 17 Users Manual.pdf Exhibit 18 Photos DUT External.pdf Exhibit 19 Photos DUT Internal.pdf Exhibit 20 Photos EMC Test Setup.pdf Exhibit Type Users Manual External Photos Internal Photos Test Setup Photos Sincerely, David Utt Staff Compliance Engineer Wellness & Fitness Products

____________________________________________________________________________________________________ Celltech Labs Inc., 21-364 Lougheed Road, Kelowna, British Columbia, Canada V1X 7R8 Tel: 1-250-765-7650 FCC Test Lab: CA3874 Date: 4 January 2022 To:

Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 USA RE: Garmin International Inc., FCC ID: IPH-04247 This is an application for a new certification of Garmin International Inc, FCC ID: IPH-04247, Model: A04247. The A04247 is a radar device containing a 2.4GHz WiFi, a Bluetooth LE (BLE) and an ANT transceiver. Certification is required in accordance with 47 CFR 15.247 and 15.249. The combinations of WiFi + ANT + Radar and BLE +

ANT + Radar transmitters can simultaneously transmit and the products of those simultaneous transmission emissions were evaluated. It is possible for the device to operate while held in hand or on body. Pursuant to 47 CFR 2.1093, the RF Exposure (SAR) was evaluated for the worst-case use configuration. The results of that SAR evaluation accompany this application. Should there be any questions or concerns with this filing, please feel free to contact me. Sincerely, Art Voss, P.Eng., BS EE Technical Manager 21-364 Lougheed Rd Kelowna, BC, V1X 7R8, Canada 250-765-7650 Ext 202 art.voss@celltechlabs.com www.celltechlabs.com Celltech Labs Inc 2021

Dec. 11, 2020 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

Innovation, Science and Economic Development Canada Certification and Engineering Bureau 3701 Carling Avenue PO Box 11490, Station H Ottawa, Ontario, Canada K2H 8S2 Pursuant to 47 CFR 2.911, Garmin International, Inc. (Garmin) has authorized the following Garmin International Associates to act on Garmin's behalf for the sole and express purpose of processing applications to the Federal Communication Commission (FCC) and Innovation, Science and Economic Development Canada (ISED) for equipment authorization or certification. Ms. Poojita Bhattu, Compliance Engineer Mr. Doug Burroughs, Senior Compliance Engineer Mr. Jeffrey Hailey, Staff Compliance Engineer Mr. Dan Irish, Senior Compliance Engineer Mr. Ben Karsak, Compliance Engineering Team Lead Mr. Kiran Kumar, Senior Compliance Engineer Mr. Tim Olson, Senior Compliance Engineer Mr. Carlos Ortega, Senior Compliance Engineer Mr. William Pertner, Compliance Engineering Team Lead Mr. Cody Riggle, Compliance Engineer Mr. David Utt, Staff Compliance Engineer Mr. Jonathan Shafer, Senior Design Certification Engineer Ms. Sara Jones, Design Certification Engineer 2 Mr. Jay Everett, Team Leader, System Validation As such, the Garmin Associates listed above are authorized to: 1) sign Form 731, 2) sign letters of application, 3) request confidentiality, and 4) exchange data and information with the FCC, IC and/or authorized TCBs on behalf of Garmin. In addition, these individuals shall be considered "authorized individuals" to act on Garmin's behalf where an "authorized individual's"

attestation is necessary or preferred. This authorization remains in effect until notified to the contrary by Garmin. Sincerely, Mr. Douglas Kealey, Manager Environmental and Regulatory Affairs

January 3, 2022 Federal Communications Commission Equip Approval Services Post Office Box 358315 Pittsburgh, Pennsylvania 15215-5315 To Whom It May Concern:

Pursuant to 47 CFR 2.911, Garmin International, Inc. (Garmin) has authorized Ben Hewson and Art Voss of Celltech Labs Inc. (Celltech) to act on Garmins behalf for the sole and express the Federal Communication Commission to purpose of processing

(FCC) for equipment FCC authorization. This authorization is limited to FCC ID: IPH-04247. applications Consistent with the foregoing, Ben Hewson and Art Voss are authorized to:

1) Sign Form 731, 2) Sign letters of application, 3) Request confidentiality, and 4) Exchange data and information with the FCC, and authorized TCBs on behalf of Garmin. This authorization is not assignable to other beyond Ben Hewson and Art Voss. No party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C 862. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. This authorization expires January 3, 2023. Sincerely, David Utt Staff Compliance Engineer, Wellness & Fitness Products

-----------------------------------------------------nothing follows----------------------------------------------------

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: January 3, 2022 SUBJECT: FCC Application for FCC ID: IPH-04247 To Whom It May Concern:

Garmin will continue to apply processes and procedures to ensure compliance with 47 CFR 2 requirements regarding products produced under supplier's Declaration of Conformity procedure for class B computer peripheral portion as applicable to this composite filing. Sincerely, David Utt Staff Compliance Engineer Wellness & Fitness Products

Tune-up Procedure Each unit is tested during unit production by measuring the output strength. The unit is then given pass/fail status based on the measured output strength. The pass/fail threshold is determined by engineering during product development. Compliant samples continue through production and non-compliant units are removed.