FCC ID: IPH-03873 Digital Transmission System Transceiver

 

GPSMAP OWNER'S MANUAL 7x2, 9x2, 12x2 Touch, A12, 7x2 Plus, 9x2 Plus, 12x2 Plus, 7x3, 9x3, 12x3 20192020 Garmin Ltd. or its subsidiaries All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product. Garmin, the Garmin logo, ActiveCaptain, ANT, BlueChart, Fusion, GPSMAP, inReach, Ultrascroll, and VIRB are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. ActiveCaptain, Apollo, Connect IQ, ECHOMAP, Fantom, Fusion-Link, Fusion PartyBus, Garmin ClearV, Garmin Connect, Garmin Express, Garmin Nautix, Garmin Quickdraw, GC, GCV, GMM, GMR, GRID, GXM, LiveScope, MotionScope, OneChart, OneHelm, Panoptix, Reactor, Shadow Drive, SmartMode, and SteadyCast are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. Apple and Mac are trademarks of Apple Inc., registered in the U.S. and other countries. Android is a trademark of Google Inc. The BLUETOOTH word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Garmin is under license. CZone is a trademark of Power Products, LLC. Color Thermal Vision is a trademark of FLIR Systems, Inc. FLIR and MSX are registered trademarks of FLIR Systems, Inc. HDMI is a registered trademark of HDMI Licensing, LLC. NMEA, NMEA 2000, and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association. microSD and the microSD logo are trademarks of SD-3C, LLC. Optimus, SeaWays, and SeaStation are registered trademarks of Dometic. SD and the SDHC logo are trademarks of SD-3C, LLC. SiriusXM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved. WiFi is a registered mark of Wi-Fi Alliance Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Yamaha, the Yamaha logo, Command Link Plus, and Helm Master are trademarks of the YAMAHA Motor Co., LTD. All other trademarks and copyrights are the property of their respective owners. Table of Contents Introduction.....................................................................1 Device Overview ......................................................................... 1 GPSMAP 7x2/7x2 Plus and GPSMAP 9x2/9x2 Plus Connector View ...................................................................... 1 GPSMAP 12x2 Touch/A12/12x2 Plus Connector View ......... 1 GPSMAP 7x3 and GPSMAP 9x3 Connector View ................ 1 GPSMAP 12x3 Connector View ............................................ 1 Using the Touchscreen .......................................................... 2 On-Screen Buttons ................................................................ 2 Locking and Unlocking the Touchscreen ............................... 2 Tips and Shortcuts (MFD models) .............................................. 2 Accessing Owner's Manuals on the Chartplotter ........................ 2 Downloading the Manuals from the Web .................................... 2 Garmin Support Center ............................................................... 2 Memory Cards ............................................................................ 2 Inserting Memory Cards (GPSMAP 7x2/9x2/12x2 Touch/A12/7x2 Plus/9x2 Plus/12x2 Plus) .............................. 3 Inserting Memory Cards (GPSMAP 7x3/9x3/12x3) ............... 3 Acquiring GPS Satellite Signals .................................................. 3 Selecting the GPS Source ..................................................... 3 Customizing the Chartplotter........................................ 3 Home Screen .............................................................................. 3 Adding an Item to Favorites ................................................... 4 Customizing the Home Screen .............................................. 4 Customizing Pages ..................................................................... 4 Customizing the Layout of a SmartMode or Combination Page .......................................................................................4 Changing the Background Image .......................................... 4 Recommended Background Image Dimensions ............... 4 Customizing the Startup Screen ............................................ 4 Recommended Startup Image Dimensions ...................... 4 Adding a SmartMode Layout ................................................. 4 Creating a New Combination Page ....................................... 5 Deleting a Combination Page ................................................ 5 Customizing the Data Overlays ............................................. 5 Resetting the Station Layouts ................................................ 5 Presets ........................................................................................ 5 Saving a New Preset ............................................................. 5 Managing Presets .................................................................. 5 Setting the Vessel Type .............................................................. 5 Adjusting the Backlight ............................................................... 5 Adjusting the Color Mode ........................................................... 5 Turning On the Chartplotter Automatically ................................. 5 Enabling Screen Lock ................................................................. 6 Automatically Turning Off the System ........................................ 6 ActiveCaptain App......................................................... 6 ActiveCaptain Roles ................................................................... 6 Getting Started with the ActiveCaptain App ............................... 6 Enabling Smart Notifications ....................................................... 6 Receiving Notifications ........................................................... 7 Managing Notifications ........................................................... 7 Making Notifications Private ................................................... 7 Updating Software with the ActiveCaptain App .......................... 7 Updating Charts with ActiveCaptain ........................................... 7 Communication with Wireless Devices........................ 7 WiFi Network ............................................................................. 8 Setting Up the WiFi Wireless Network .................................. 8 Connecting a Wireless Device to the Chartplotter ................. 8 Changing the Wireless Channel ............................................ 8 Changing the WiFi Host ........................................................ 8 Wireless Remote Control ............................................................ 8 Pairing the Wireless Remote Control With the Chartplotter ............................................................................ 8 Turning On and Off the Remote Backlight ............................. 8 Disconnecting the Remote from All Chartplotters .................. 8 Wireless Wind Sensor ................................................................ 8 Connecting a Wireless Sensor to the Chartplotter ................. 8 Adjusting the Wind Sensor Orientation .................................. 8 Viewing Boat Data on a Garmin Watch ...................................... 8 Viewing Boat Data on a Garmin Nautix Device ...................... 9 Charts and 3D Chart Views........................................... 9 Navigation Chart and Fishing Chart ........................................... 9 Zooming In and Out Using the Touchscreen ......................... 9 Chart Symbols ....................................................................... 9 Measuring a Distance on the Chart ....................................... 9 Creating a Waypoint on the Chart .......................................... 9 Viewing Location and Object Information on a Chart ............ 9 Viewing Details about Navaids ............................................ 10 Navigating to a Point on the Chart ....................................... 10 Premium Charts ........................................................................ 10 Fish Eye 3D Chart View ....................................................... 10 Viewing Tide Station Information ......................................... 10 Animated Tide and Current Indicators ............................ 10 Showing Tides and Current Indicators ............................ 11 Showing Satellite Imagery on the Navigation Chart ............ 11 Viewing Aerial Photos of Landmarks ................................... 11 Automatic Identification System ................................................ 11 AIS Targeting Symbols ........................................................ 11 Heading and Projected Course of Activated AIS Targets .... 11 Activating a Target for an AIS Vessel .................................. 12 Viewing Information about a Targeted AIS Vessel ......... 12 Deactivating a Target for an AIS Vessel ......................... 12 Viewing a List of AIS and MARPA Threats .......................... 12 Setting the Safe-Zone Collision Alarm ................................. 12 AIS Aids to Navigation ......................................................... 12 AIS Distress Signals ............................................................ 12 Navigating to a Distress Signal Transmission ................. 12 AIS Distress Signal Device Targeting Symbols .............. 12 Enabling AIS Transmission Test Alerts ........................... 12 Turning Off AIS Reception ................................................... 13 Chart Menu ............................................................................... 13 Chart Layers ........................................................................ 13 Chart Layer Settings ....................................................... 13 Depth Layer Settings ....................................................... 13 My Vessel Layer Settings ................................................ 13 Laylines Settings ............................................................. 13 User Data Layer Settings ................................................ 14 Other Vessels Layer Settings .......................................... 14 Water Layer Settings ....................................................... 14 Depth Range Shading ..................................................... 14 Weather Layer Settings ................................................... 14 Radar Overlay Settings ................................................... 15 Chart Settings ...................................................................... 15 Fish Eye 3D Settings ........................................................... 15 Supported Maps ....................................................................... 15 Garmin Quickdraw Contours Mapping....................... 15 Mapping a Body of Water Using the Garmin Quickdraw Contours Feature ...................................................................... 15 Adding a Label to a Garmin Quickdraw Contours Map ............ 15 Garmin Quickdraw Community ................................................. 15 Connecting to the Garmin Quickdraw Community with ActiveCaptain ....................................................................... 16 Downloading Garmin Quickdraw Community Maps Using ActiveCaptain .................................................................. 16 Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using ActiveCaptain ...... 16 Connecting to the Garmin Quickdraw Community with Garmin Connect ................................................................... 16 Table of Contents i Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using Garmin Connect .. 16 Downloading Garmin Quickdraw Community Maps Using Garmin Connect .............................................................. 16 Garmin Quickdraw Contours Settings ...................................... 16 Navigation with a Chartplotter.................................... 17 Basic Navigation Questions ...................................................... 17 Destinations .............................................................................. 17 Searching for a Destination by Name .................................. 17 Selecting a Destination Using the Navigation Chart ............ 17 Searching for a Marine Services Destination ....................... 17 Setting and Following a Direct Course Using Go To ........... 18 Stopping Navigation ............................................................. 18 Waypoints ................................................................................. 18 Marking Your Present Location as a Waypoint .................... 18 Creating a Waypoint at a Different Location ........................ 18 Marking an SOS Location .................................................... 18 Projecting a Waypoint .......................................................... 18 Viewing a List of all Waypoints ............................................ 18 Editing a Saved Waypoint .................................................... 18 Moving a Saved Waypoint ................................................... 18 Browsing for and Navigating to a Saved Waypoint .............. 18 Deleting a Waypoint or an MOB .......................................... 19 Deleting All Waypoints ......................................................... 19 Routes ...................................................................................... 19 Creating and Navigating a Route From Your Present Location ............................................................................... 19 Creating and Saving a Route ............................................... 19 Viewing a List of Routes and Auto Guidance Paths ............ 19 Editing a Saved Route ......................................................... 19 Browsing for and Navigating a Saved Route ....................... 19 Browsing for and Navigating Parallel to a Saved Route ...... 19 Initiating a Search Pattern .................................................... 20 Deleting a Saved Route ....................................................... 20 Deleting All Saved Routes ................................................... 20 Auto Guidance .......................................................................... 20 Setting and Following an Auto Guidance Path .................... 20 Creating and Saving an Auto Guidance Path ...................... 20 Adjusting a Saved Auto Guidance Path ............................... 20 Canceling an Auto Guidance Calculation in Progress ......... 20 Setting a Timed Arrival ......................................................... 20 Auto Guidance Path Configurations .................................... 20 Adjusting the Distance from Shore .................................. 21 Tracks ....................................................................................... 21 Showing Tracks ................................................................... 21 Setting the Color of the Active Track ................................... 21 Saving the Active Track ....................................................... 21 Viewing a List of Saved Tracks ............................................ 21 Editing a Saved Track .......................................................... 21 Saving a Track as a Route ................................................... 21 Browsing for and Navigating a Recorded Track .................. 21 Deleting a Saved Track ........................................................ 22 Deleting All Saved Tracks .................................................... 22 Retracing the Active Track ................................................... 22 Clearing the Active Track ..................................................... 22 Managing the Track Log Memory During Recording ........... 22 Configuring the Recording Interval of the Track Log ........... 22 Boundaries ................................................................................22 Creating a Boundary ............................................................ 22 Converting a Route to a Boundary ...................................... 22 Converting a Track to a Boundary ....................................... 22 Editing a Boundary ............................................................... 22 Linking a Boundary to a SmartMode Layout ........................ 22 Setting a Boundary Alarm .................................................... 22 Disabling all Boundary Alarms ............................................. 23 Deleting a Boundary ............................................................ 23 Deleting All Saved Waypoints, Tracks, Routes, and Boundaries ................................................................................23 Sailing Features............................................................ 23 Setting the Vessel Type ............................................................ 23 Sail Racing ................................................................................ 23 Starting Line Guidance ........................................................ 23 Setting the Starting Line .................................................. 23 Using the Starting Line Guidance ................................... 23 Starting the Race Timer ....................................................... 23 Stopping the Race Timer ..................................................... 23 Setting the Distance between the Bow and the GPS Antenna ................................................................................23 Laylines Settings ....................................................................... 23 Setting the Keel Offset .............................................................. 24 Sailboat Autopilot Operation ..................................................... 24 Wind Hold ............................................................................ 24 Setting the Wind Hold Type ............................................ 24 Engaging Wind Hold ....................................................... 24 Engaging Wind Hold from Heading Hold ........................ 24 Adjusting the Wind Hold Angle with the Autopilot ........... 24 Tack and Gybe ..................................................................... 24 Tacking and Gybing from Heading Hold ......................... 24 Tacking and Gybing from Wind Hold .............................. 24 Setting a Tack and Gybe Delay ...................................... 24 Enabling the Gybe Inhibitor ............................................. 25 Heading Line and Angle Markers ............................................. 25 Setting the Heading Line and Angle Markers ...................... 25 Sonar Fishfinder........................................................... 25 Stopping the Transmission of Sonar Signals ............................ 25 Changing the Sonar View ......................................................... 25 Traditional Sonar View .............................................................. 25 Split-Frequency Sonar View ................................................ 25 Split-Zoom Sonar View ........................................................ 25 Garmin ClearV Sonar View ..................................................... 25 SideV Sonar View ................................................................... 26 SideV Scanning Technology .............................................. 26 Measuring Distance on the Sonar Screen ........................... 26 Panoptix Sonar Views ............................................................... 26 LiveV Down Sonar View .................................................... 26 LiveV Forward Sonar View ................................................ 27 RealV 3D Forward Sonar View .......................................... 27 RealV 3D Down Sonar View .............................................. 27 RealV 3D Historical Sonar View ........................................ 27 FrontV Sonar View ............................................................. 27 Panoptix LiveScope Sonar View ...................................... 27 Perspective View ................................................................. 28 Selecting the Transducer Type ................................................. 28 Selecting a Sonar Source ......................................................... 28 Renaming a Sonar Source ................................................... 28 Creating a Waypoint on the Sonar Screen ............................... 28 Pausing the Sonar Display ....................................................... 28 Viewing Sonar History .............................................................. 28 Sonar Sharing ........................................................................... 28 Adjusting the Level of Detail ..................................................... 28 Adjusting the Color Intensity ..................................................... 28 Sonar Recordings ..................................................................... 29 Recording the Sonar Display ............................................... 29 Stopping the Sonar Recording ............................................. 29 Deleting a Sonar Recording ................................................. 29 Playing Sonar Recordings ................................................... 29 Traditional, Garmin ClearV, and SideV Sonar Setup ........... 29 Setting the Zoom Level on the Sonar Screen ...................... 29 Setting the Scroll Speed ...................................................... 29 Adjusting the Range of the Depth or Width Scale ............... 30 Sonar Noise Rejection Settings ........................................... 30 Sonar Appearance Settings ................................................. 30 ii Table of Contents Sonar Alarms ....................................................................... 30 Advanced Sonar Settings .................................................... 31 Traditional, Garmin ClearV, and SideV Transducer Installation Settings .............................................................. 31 Sonar Frequencies ............................................................... 31 Selecting the Transducer Frequency .............................. 31 Creating a Frequency Preset .......................................... 31 Turning On the A-Scope ...................................................... 31 Panoptix Sonar Setup ............................................................... 32 Zooming in a Panoptix LiveV or LiveScope Sonar View .... 32 Adjusting the RealV Viewing Angle and Zoom Level ......... 32 Adjusting the RealV Sweep Speed .................................... 32 LiveV Forward and FrontV Sonar Menu .......................... 32 Setting the LiveV and FrontV Transducer Transmit Angle ............................................................................... 32 Setting the FrontV Depth Alarm .................................... 33 LiveV and FrontV Appearance Settings ........................... 33 RealV Appearance Settings ............................................... 33 LiveScope and Perspective Sonar Menu ............................. 33 LiveScope and Perspective Sonar Setup ............................ 33 LiveScope and Perspective Appearance Settings ............... 34 Panoptix Transducer Installation Settings ........................... 34 Setting the Bow Offset .................................................... 34 Calibrating the Compass ................................................. 34 Radar ............................................................................. 35 Radar Interpretation .................................................................. 35 Radar Overlay ...................................................................... 35 Radar Overlay and Chart Data Alignment ........................... 35 Transmitting Radar Signals ...................................................... 35 Stopping the Transmission of Radar Signals ....................... 35 Setting Up the Timed Transmit Mode .................................. 35 Enabling and Adjusting a Radar No Transmit Zone ............ 35 Adjusting the Radar Range ...................................................... 35 Tips for Selecting a Radar Range ........................................ 36 MotionScope Doppler Radar Technology ............................. 36 Enabling a Guard Zone ............................................................ 36 Defining a Circular Guard Zone ........................................... 36 Defining a Partial Guard Zone ............................................. 36 MARPA ..................................................................................... 36 MARPA Targeting Symbols ................................................. 36 Acquiring MARPA Targets Automatically ............................. 36 Assigning a MARPA Tag to an Object ................................. 37 Removing a MARPA Tag from a Targeted Object ............... 37 Viewing Information about a MARPA-tagged Object ........... 37 Viewing a List of AIS and MARPA Threats .......................... 37 Showing AIS Vessels on the Radar Screen ........................ 37 VRM and EBL ...................................................................... 37 Showing and Adjusting the VRM and the EBL ................ 37 Measuring the Range and Bearing to a Target Object ... 37 Echo Trails ................................................................................ 37 Turning on Echo Trails ......................................................... 37 Adjusting the Length of the Echo Trails ............................... 37 Clearing the Echo Trails ....................................................... 37 Radar Settings .......................................................................... 37 Radar Gain ........................................................................... 37 Adjusting Gain on the Radar Screen Automatically ........ 37 Adjusting Gain on the Radar Screen Manually ............... 38 Minimizing Nearby Large-Object Interference ................. 38 Minimizing Side-Lobe Interference on the Radar Screen ............................................................................. 38 Radar Filter Settings ............................................................ 38 Adjusting Sea Clutter on the Radar Screen .................... 38 Adjusting Rain Clutter on the Radar Screen ................... 38 Averaging Multiple Scans on the Radar Screen ............. 38 Radar Options Menu ............................................................ 38 Radar Setup Menu ............................................................... 39 Reducing Cross Talk Clutter on the Radar Screen ......... 39 Radar Appearance Settings ................................................. 39 Radar Installation Settings ................................................... 39 Front-of-Boat Offset ........................................................ 39 Setting a Custom Park Position ...................................... 39 Radar My Vessel Layer Settings .......................................... 39 Selecting a Different Radar Source .......................................... 39 Changing the Radar Mode ....................................................... 39 Autopilot........................................................................ 39 Opening the Autopilot Screen ................................................... 40 Autopilot Screen ....................................................................... 40 Adjusting the Step Steering Increment ................................ 40 Setting the Power Saver ...................................................... 40 Enabling Shadow Drive .................................................... 40 Selecting the Preferred Heading Source ............................. 40 Autopilot Overlay Bar ................................................................ 40 Engaging the Autopilot ............................................................. 40 Adjusting the Heading with the Helm ................................... 40 Adjusting the Heading with the Chartplotter in Step Steering Mode .................................................................................... 40 Steering Patterns ...................................................................... 41 Following the U-Turn Pattern ............................................... 41 Setting Up and Following the Circles Pattern ...................... 41 Setting Up and Following the Zigzag Pattern ...................... 41 Following the Williamson Turn Pattern ................................ 41 Following an Orbit Pattern ................................................... 41 Setting Up and Following the Cloverleaf Pattern ................. 41 Setting Up and Following a Search Pattern ......................... 41 Cancelling a Steering Pattern .............................................. 41 Adjusting the Autopilot Response ............................................. 41 Enabling the Autopilot Controls on a Garmin Watch ................ 41 Customizing the Autopilot Button Actions ............................ 41 Controlling the Autopilot with a GRID 20 Remote Control ........ 41 Reactor Autopilot Remote Control ........................................ 42 Pairing a Reactor Autopilot Remote Control With a Chartplotter .......................................................................... 42 Changing the Functions of the Reactor Autopilot Remote Control Action Keys ............................................................. 42 Updating the Reactor Autopilot Remote Control Software .. 42 Yamaha Autopilot ..................................................................... 42 Yamaha Autopilot Screen .................................................... 42 Yamaha Autopilot Settings .............................................. 42 Yamaha Autopilot Overlay Bar ............................................. 42 Force Trolling Motor Control.................................... 43 Connecting to a Trolling Motor .................................................. 43 Adding the Trolling Motor Controls to Screens ......................... 43 Trolling Motor Control Bar .................................................... 43 Trolling Motor Settings .............................................................. 43 Assigning a Shortcut to the Trolling Motor Remote Control Shortcut Keys ....................................................................... 44 Calibrating the Trolling Motor Compass ............................... 44 Setting the Bow Offset ......................................................... 44 Digital Selective Calling............................................... 44 Networked Chartplotter and VHF Radio Functionality .............. 44 Turning On DSC ....................................................................... 44 DSC List .................................................................................... 44 Viewing the DSC List ........................................................... 44 Adding a DSC Contact ......................................................... 44 Incoming Distress Calls ............................................................ 44 Navigating to a Vessel in Distress ....................................... 44 Man-Overboard Distress Calls Initiated from a VHF Radio .................................................................................... 44 Man-Overboard and SOS Distress Calls Initiated from the Chartplotter .......................................................................... 45 Position Tracking ...................................................................... 45 Table of Contents iii Viewing a Position Report .................................................... 45 Navigating to a Tracked Vessel ........................................... 45 Creating a Waypoint at the Position of a Tracked Vessel .... 45 Editing Information in a Position Report .............................. 45 Deleting a Position-Report Call ............................................ 45 Viewing Vessel Trails on the Chart ...................................... 45 Individual Routine Calls ............................................................ 45 Selecting a DSC Channel .................................................... 45 Making an Individual Routine Call ....................................... 45 Making an Individual Routine Call to an AIS Target ............ 45 Gauges and Graphs..................................................... 45 Viewing the Gauges .................................................................. 45 Changing the Data Shown in a Gauge ................................ 45 Customizing the Gauges ...................................................... 46 Customizing Engine Gauge and Fuel Gauge Limits ............ 46 Selecting the Number of Engines Shown in Gauges ........... 46 Customizing the Engines Shown in Gauges ........................ 46 Enabling Status Alarms for Engine Gauges ........................ 46 Enabling Some Engine Gauge Status Alarms ..................... 46 Yamaha Engine Gauges .......................................................... 46 Engine Condition Icons ........................................................ 46 Engine Alert Icons ................................................................ 46 Setting Up the Gauges ......................................................... 47 Configuring the Number of Engines ................................ 47 Configuring the Tank Level Sensors ............................... 47 Changing the Data Shown .............................................. 47 Yamaha Engine Data Settings ........................................ 47 Setting the Fuel Alarm .............................................................. 47 Setting the Fuel Capacity of the Vessel ............................... 47 Synchronizing the Fuel Data with the Actual Vessel Fuel ... 47 Viewing the Wind Gauges ........................................................ 48 Configuring the Sailing Wind Gauge .................................... 48 Configuring the Speed Source ............................................. 48 Configuring the Heading Source of the Wind Gauge ........... 48 Customizing the Close-Hauled Wind Gauge ....................... 48 Viewing Trip Gauges ................................................................ 48 Resetting Trip Gauges ......................................................... 48 Battery Management ................................................................ 48 Setting Up the Battery Management Page .......................... 48 Viewing Graphs ........................................................................ 48 Setting the Graph Range and Time Scales ......................... 48 inReach Messages ..................................................... 48 Connecting an inReach Device to the Chartplotter .................. 48 Receiving inReach Messages .................................................. 49 Sending an inReach Preset Message ...................................... 49 Replying to an inReach Message ............................................. 49 Digital Switching.......................................................... 49 Adding and Editing a Digital Switching Page ............................ 49 Dometic Optimus Features.................................... 49 Activating the Optimus Overlay Bar .......................................... 49 Optimus Overlay Bar Overview ................................................ 49 Optimus Overlay Symbols ........................................................ 49 Optimus Limp Home Mode ....................................................... 49 Tide, Current, and Celestial Information.................... 50 Tide Station Information ............................................................ 50 Current Station Information ....................................................... 50 Celestial Information ................................................................. 50 Viewing Tide Station, Current Station, or Celestial Information for a Different Date ................................................................... 50 Viewing Information for a Different Tide or Current Station ...... 50 Viewing Almanac Information from the Navigation Chart ......... 50 Warning Manager......................................................... 50 Viewing Messages .................................................................... 50 Sorting and Filtering Messages ................................................ 50 Saving Messages to a Memory Card ........................................ 50 Clearing all of the Messages .................................................... 50 Media Player................................................................. 50 Opening the Media Player ........................................................ 50 Media Player Icons .............................................................. 50 Selecting the Media Device and Source ................................... 51 Playing Music ............................................................................ 51 Browsing for Music ............................................................... 51 Enabling Alphabetical Search ......................................... 51 Setting a Song to Repeat ..................................................... 51 Setting All Songs to Repeat ................................................. 51 Setting Songs to Shuffle ...................................................... 51 Joining the Fusion PartyBus Network .............................. 51 Adjusting the Volume ................................................................ 51 Muting the Media Volume .................................................... 51 Enabling and Disabling Zones ............................................. 51 VHF Radio ................................................................................ 51 Scanning VHF Channels ...................................................... 51 Adjusting the VHF Squelch .................................................. 51 Radio ........................................................................................ 51 Setting the Tuner Region ..................................................... 51 Changing the Radio Station ................................................. 51 Changing the Tuning Mode ................................................. 51 Presets ................................................................................. 51 Saving a Station as a Preset ........................................... 51 Selecting a Preset ........................................................... 51 Removing a Preset .......................................................... 52 DAB Playback ........................................................................... 52 Setting the DAB Tuner Region ............................................ 52 Scanning for DAB Stations .................................................. 52 Changing DAB Stations ....................................................... 52 Selecting a DAB Station from a List ................................ 52 Selecting a DAB Station from a Category ....................... 52 DAB Presets ........................................................................ 52 Saving a DAB Station as a Preset .................................. 52 Selecting a DAB Preset from a List ................................. 52 Removing DAB Presets .................................................. 52 SiriusXM Satellite Radio ........................................................... 52 Locating a SiriusXM Radio ID .............................................. 52 Activating a SiriusXM Subscription ...................................... 52 Customizing the Channel Guide .......................................... 52 Saving a SiriusXM Channel to the Presets List ................... 52 Parental Controls ................................................................. 53 Unlocking SiriusXM Parental Controls ............................ 53 Setting Parental Controls on SiriusXM Radio Channels ......................................................................... 53 Clearing All Locked Channels on a SiriusXM Radio ....... 53 Restoring Default Parental Control Settings Values ....... 53 Changing a Parental Passcode on a SiriusXM Radio ..... 53 Setting the Device Name .......................................................... 53 Updating the Media Player Software ........................................ 53 SiriusXM Weather ......................................................... 53 SiriusXM Equipment and Subscription Requirements .............. 53 Weather Data Broadcasts ......................................................... 53 Weather Warnings and Weather Bulletins ................................ 53 Changing the Weather Chart .................................................... 54 Viewing Precipitation Information ............................................. 54 Storm Cell and Lightning Information .................................. 54 Hurricane Information .......................................................... 54 Forecast Information ................................................................. 54 Viewing a Marine Forecast or an Offshore Forecast ........... 54 Viewing Forecast Information for Another Time Period ....... 54 Weather Fronts and Pressure Centers ................................ 54 City Forecasts ...................................................................... 54 Viewing Fish Mapping Data ...................................................... 54 Viewing Sea Conditions ............................................................ 54 iv Table of Contents Surface Winds ...................................................................... 54 Wave Height, Wave Period, and Wave Direction ................ 55 Viewing Forecast Sea Conditions Information for Another Time Period .......................................................................... 55 Viewing Sea Temperature Information ..................................... 55 Surface Pressure and Water Temperature Data ................. 55 Changing the Sea Surface Temperature Color Range ........ 55 Visibility Information .................................................................. 55 Viewing Forecast Visibility Information for Another Time Period ................................................................................... 55 Viewing Buoy Reports .............................................................. 55 Viewing Local Weather Information near a Buoy ................. 55 Weather Overlay ....................................................................... 55 Viewing Weather Subscription Information ............................... 55 Viewing Video............................................................... 55 Selecting a Video Source ......................................................... 56 Alternating Among Multiple Video Sources ......................... 56 Networked Video Devices ......................................................... 56 Using Video Presets on Networked Video Cameras ........... 56 Saving Video Presets on a Networked Video Camera ... 56 Naming Video Presets on a Networked Video Camera .. 56 Activating Video Presets on a Networked Video Camera ........................................................................... 56 Camera Settings .................................................................. 56 Video Settings ...................................................................... 56 Associating the Camera to a Video Source ......................... 56 Video Camera Movement Control ........................................ 56 Controlling Video Cameras Using On-Screen Controls .. 57 Controlling a Video Camera Using Gestures .................. 57 Configuring the Video Appearance ........................................... 57 Garmin VIRB Action Cameras ............................................... 57 Connecting a VIRB 360 Action Camera .............................. 57 Connecting a VIRB Action Camera ...................................... 57 Controlling the VIRB Action Camera with the Chartplotter .. 57 Controlling the VIRB Action Camera Video Playback ..... 58 Deleting a VIRB Video .................................................... 58 Starting a VIRB Video Slideshow .................................... 58 VIRB Action Camera Settings ......................................... 58 VIRB Action Camera Video Setup Settings .................... 58 Adding the VIRB Action Camera Controls to Other Screens ................................................................................ 58 HDMI Out Video Considerations ............................................... 58 Pairing the GC 100 Camera with a Garmin Chartplotter ....... 58 Device Configuration................................................... 59 System Settings ........................................................................ 59 Sounds and Display Settings ............................................... 59 GPS Settings ....................................................................... 59 Station Settings .................................................................... 59 Viewing System Software Information ................................. 59 Viewing the Event Log .................................................... 59 Viewing E-label Regulatory and Compliance Information .... 59 Preferences Settings ................................................................ 59 Units Settings ....................................................................... 59 Navigation Settings .............................................................. 60 Auto Guidance Path Configurations ................................ 60 Adjusting the Distance from Shore .................................. 60 Communications Settings ......................................................... 60 NMEA 0183 Settings ............................................................ 60 Configuring NMEA 0183 Output Sentences ................... 61 Setting the Communication Format for Each NMEA 0183 Port .................................................................................. 61 NMEA 2000 Settings ............................................................ 61 Naming Devices and Sensors on the Network ............... 61 Marine Network .................................................................... 61 Setting Alarms .......................................................................... 61 Navigation Alarms ................................................................ 61 Setting the Anchor Drag Alarm ....................................... 61 System Alarms ..................................................................... 61 Sonar Alarms ....................................................................... 61 Setting Weather Alarms ....................................................... 62 Setting the Fuel Alarm ......................................................... 62 My Vessel Settings ................................................................... 62 Setting the Keel Offset ......................................................... 62 Setting the Water Temperature Offset ................................. 62 Calibrating a Water-Speed Device ....................................... 63 Other Vessels Settings ............................................................. 63 Settings that are Synced on the Garmin Marine Network ........ 63 Restoring the Original Chartplotter Factory Settings ................ 63 Sharing and Managing User Data............................... 64 Selecting a File Type for Third-Party Waypoints and Routes ... 64 Copying User Data from a Memory Card ................................. 64 Copying User Data to a Memory Card ...................................... 64 Updating Built-In Maps with a Memory Card and Garmin Express ..................................................................................... 64 Backing Up Data to a Computer ............................................... 64 Restoring Backup Data to a Chartplotter .................................. 64 Saving System Information to a Memory Card ......................... 64 Appendix....................................................................... 64 ActiveCaptain and Garmin Express .......................................... 64 Garmin Express App ................................................................. 65 Installing the Garmin Express App on a Computer .............. 65 Registering Your Device Using the Garmin Express App .... 65 Updating Your Charts Using the Garmin Express App ........ 65 Software Updates ................................................................ 65 Loading the New Software on a Memory Card Using Garmin Express .............................................................. 66 Updating the Device Software Using a Memory Card .... 66 Pairing the GRID Device with the Chartplotter from the Chartplotter ............................................................................... 66 Pairing the GRID Device with the Chartplotter from the GRID Device .................................................................................. 66 Rotating the GRID Remote Input Device ............................. 66 Cleaning the Screen ................................................................. 66 Viewing Images on a Memory card .......................................... 66 Screenshots .............................................................................. 67 Capturing Screenshots ........................................................ 67 Copying Screenshots to a Computer ................................... 67 Troubleshooting ........................................................................ 67 My device will not acquire GPS signals ............................... 67 My device will not turn on or keeps turning off ..................... 67 My device is not creating waypoints in the correct location ................................................................................. 67 Contacting Garmin Support ...................................................... 67 Specifications ............................................................................ 67 GPSMAP 7x2/7x2 Plus Specifications ................................. 67 GPSMAP 9x2/9x2 Plus Specifications ................................. 68 GPSMAP 12x2 Touch/A12/12x2 Plus Specifications .......... 68 GPSMAP 7x3 Specifications ................................................ 68 GPSMAP 9x3 Specifications ................................................ 68 GPSMAP 12x3 Specifications .............................................. 69 Sonar Models Specifications ................................................ 69 NMEA 2000 PGN Information .............................................. 69 NMEA 0183 Information ....................................................... 70 J1939 Information ................................................................ 70 Index.............................................................................. 71 Table of Contents v Introduction WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. All route and navigation lines displayed on the chartplotter are only intended to provide general route guidance or to identify proper channels, and are not intended to be precisely followed. Always defer to the navaids and conditions on the water when navigating to avoid groundings or hazards that could result in vessel damage, personal injury, or death. NOTE: Not all features are available on all models. The Garmin website at support.garmin.com presents up-to-date information about your product. The support pages will provide answers to frequently asked support questions, and you can download software and chart updates. There is also contact information to Garmin support should you have any questions. Device Overview SONAR POWER 12-pin transducer (Not available on all models) Power and NMEA 0183 network Ground screw CVBS IN Composite video in J1939 Engine or J1939 network ETHERNET HDMI OUT Garmin Marine Network HDMI video out NMEA 2000 NMEA 2000 network GPSMAP 7x3 and GPSMAP 9x3 Connector View Touchscreen Power key Automatic backlight sensor 12x2/A12 models: 2 SD memory card slots. 7x2/9x2 models: 2 microSD memory card slots. 7x3/9x3/12x3 models: 2 microSD memory card slots are on the back of the device. All models: 32 GB max. card size. POWER Power and NMEA 0183 network ETHERNET Garmin Marine Network J1939 J1939 engine network GPSMAP 7x2/7x2 Plus and GPSMAP 9x2/9x2 Plus Connector View The connectors and locations vary based upon the model. This image and table represent a GPSMAP 922xs Plus model. CVBS IN SONAR USB NMEA 2000 Ground screw Composite video in 12-pin transducer (Not available on all models) Micro-USB for compatible Garmin card reader1 NMEA 2000 network 2 microSD memory card slots, 32 GB max. GPSMAP 12x3 Connector View J1939 engine network (Not available on all models) J1939 NMEA 2000 NMEA 2000 network CVBS IN Composite video in ETHERNET Garmin Marine Network 8-PIN XDCR 8-pin transducer (Not available on all models) POWER Power and NMEA 0183 network Ground screw GPSMAP 12x2 Touch/A12/12x2 Plus Connector View The connectors and locations vary based upon the model. 1 Only compatible Garmin card readers recommended. Third-party card readers are not guaranteed to be fully compatible. Introduction 1 POWER SONAR Power and NMEA 0183 network 12-pin transducer (Not available on all models) HDMI OUT HDMI video out 2 microSD memory card slots, 32 GB max. On the home screen of some models, swipe up or down on CVBS IN USB Composite video in Micro-USB for compatible Garmin card reader1 Ground screw ETHERNET Garmin Marine Network NMEA 2000 NMEA 2000 network J1939 Engine or J1939 network Using the Touchscreen Tap the screen to select an item. Drag or swipe your finger across the screen to pan or scroll. Pinch two fingers together to zoom out. Spread two fingers apart to zoom in. On-Screen Buttons These on-screen buttons may be displayed on some screens and functions. Some buttons are accessible only in a combination page or SmartMode layout or when accessories, such as a radar, are connected. Button Function Clears the on-screen icons and re-centers the screen on the boat Opens a full-screen view of the item Creates a new waypoint Creates a route, with turns, to the destination Adds a turn to the route at the selected location Removes the last added turn from the route Creates a direct route, without turns, to the destination Creates an Auto Guidance route to the destination Begins navigation Ends navigation Stops and starts radar transmission Opens the radar gain adjustment menu Opens the radar sea clutter adjustment menu Opens the radar rain clutter adjustment menu Turns on and off the radar echo trails Acquires a radar target and begins tracking it Shows and sets the VRM/EBL line Opens the menu for the page or function Opens the Weather menu for the page or function Opens the Radar menu for the page or function Opens the Presets menu for the page or function Locking and Unlocking the Touchscreen You can lock the touchscreen to prevent inadvertent screen touches. 1 Select 2 Select

> Lock Touchscreen to lock the screen. to unlock the screen. Tips and Shortcuts (MFD models) Press From any screen, press to turn on the chartplotter. repeatedly to scroll through the brightness levels, if available. This can be helpful when the brightness is so low you cannot see the screen. Select Home from any screen to return to the Home screen. Select Menu to open additional settings about that screen. Select Menu to close the menu when finished. 1 Only compatible Garmin card readers recommended. Third-party card readers are not guaranteed to be fully compatible. Press to open additional options, such as locking the touchscreen. Press

, and select Power > Turn Off System, or hold until the Turn Off System bar fills to turn off the chartplotter, when available. Press

, and select Power > Sleep Station to set the chartplotter to standby mode, when available. the category buttons along the right side of the screen to view the additional buttons. On some models, not all category buttons are visible. The arrows at the top or bottom of the buttons indicate not all buttons are visible. On some menu buttons, select the button to enable the option. A green light on an option indicates the option is enabled

. When available, select the arrow to open the menu. Accessing Owner's Manuals on the Chartplotter 1 Select Info > Owner's Manual. 2 Select a manual. 3 Select Open. Downloading the Manuals from the Web You can get the latest owner's manual and translations of manuals from the Garmin website. The owner's manual includes instructions for using device features and accessing regulatory information. 1 Go to garmin.com/manuals/GPSMAPPlus. 2 Download the manual. Garmin Support Center Go to support.garmin.com for help and information, such as product manuals, frequently asked questions, videos, software updates, and customer support. Memory Cards You can use optional memory cards with the chartplotter. Map cards allow you to view high-resolution satellite imagery and aerial reference photos of ports, harbors, marinas, and other points of interest. You can use blank memory cards to record Garmin Quickdraw Contours mapping, record sonar (with a compatible transducer), transfer data such as waypoints and routes to another compatible chartplotter or a computer, and use the ActiveCaptain app. This device supports up to a 32 GB memory card, formatted to FAT32 with speed class 4 or higher. Use of an 8 GB or higher memory card with speed class 10 is recommended. Model Memory Card Location Memory Card GPSMAP 7x2/7x2 Plus Front of the device GPSMAP 9x2/9x2 Plus Front of the device GPSMAP 12x2 Touch/A12/12x2 Plus Front of the device SD GPSMAP 7x3/9x3/12x3 Back of the device microSD Type microSD microSD 2 Introduction Inserting Memory Cards (GPSMAP 7x2/9x2/12x2 Touch/A12/7x2 Plus/9x2 Plus/12x2 Plus) You can use optional memory cards with the chartplotter. Map cards allow you to view high-resolution satellite imagery and aerial reference photos of ports, harbors, marinas, and other points of interest. You can use blank memory cards to record Garmin Quickdraw Contours mapping, record sonar (with a compatible transducer), transfer data such as waypoints and routes to another compatible chartplotter or a computer, and use the ActiveCaptain app. This device supports up to a 32 GB memory card, formatted to FAT32 with speed class 4 or higher. Use of an 8 GB or higher memory card with speed class 10 is recommended. 12x2/A12 models use an SD memory card. 7x2/9x2 models use a microSD memory card. 1 Open the access flap or door on the front of the chartplotter. 2 Insert the memory card 3 Press the card in until it clicks. 4 Clean and dry the gasket and door. NOTICE To prevent corrosion, be sure the memory card, gasket, and door are thoroughly dry before closing the door. 5 Close the door. Inserting Memory Cards (GPSMAP 7x3/9x3/12x3) This device supports up to a 32 GB microSD memory card, formatted to FAT32 with speed class 4 or higher. Use of an 8 GB or higher memory card with speed class 10 is recommended. 1 Open the weather cap on the back of the chartplotter. 2 Insert the memory card 3 Press the card in until it clicks. 4 Press the weather cap firmly shut to prevent corrosion. Acquiring GPS Satellite Signals The device may need a clear view of the sky to acquire satellite signals. The time and date are set automatically based on the GPS position. 1 Turn on the device. 2 Wait while the device locates satellites. It may take 30 to 60 seconds to acquire satellite signals. appears at the When the device acquires satellite signals, top of the Home screen. If the device loses satellite signals, flashing question mark appears over on the chart. For more information about GPS, go to garmin.com/aboutGPS. For help acquiring satellite signals, see My device will not acquire GPS signals, page 67. disappears and a Selecting the GPS Source You can select your preferred source for GPS data, if you have more than one GPS source. 1 Select Settings > System > GPS > Source. 2 Select the source for GPS data. Customizing the Chartplotter Home Screen The chartplotter home screen provides access to all of the features in the chartplotter. The features are dependant on the accessories you have connected to the chartplotter. You may not have all of the options and features discussed in this manual. When viewing another screen, you can return to the home screen by selecting Home. Status bar Pages buttons Categories bar Menu bar The categories along the right of the screen provide quick access to the main features of your chartplotter. For example, the Sonar category displays the views and pages related to the sonar feature. You can save items you commonly access to the Favorites category. TIP: If your home screen has been customized by the boat manufacturer, you can open the original home page category tabs by dragging the bar on the right side of the screen to the left. The SmartMode items are geared toward an activity, such as cruising or docking. When a SmartMode button is selected from the home screen, each display in the station can show unique information. For example, when Cruising is selected from the home screen, one display can show the navigation chart and another display can show the radar screen. All of the options along the bottom of the home screen are visible on all other screens, except for the Settings button. The Settings button is accessible only from the home screen. An indicator appears on the Info button when an alarm is activated (Warning Manager, page 50). When multiple displays are installed on the Garmin Marine Network, you can group them together into a station. A station enables the displays to work together, instead of as several separate displays. You can customize the layout of the pages on Customizing the Chartplotter 3 each display, making each page different on each display. When you change the layout of a page in one display, the changes appear on only that display. When you change the name and symbol of the layout, those changes appear on all displays in the station, to maintain a consistent appearance. Changing the Background Image 1 From the home screen, select Menu > Background. TIP: You can also adjust this setting from Settings > System

> Sounds and Display > Background. Adding an Item to Favorites You can add items such as a chart, combo screen, or gauge to the Favorites category. NOTE: If your home screen has been customized by the boat manufacturer, you cannot add an item to the Favorites category. 1 From the home screen, select a category from the right. 2 Hold a button on the left. The item is added to the Favorites home screen category. To remove an item you have added to the Favorites category, open the Favorites category, select Menu > Remove Favorite, and select the item to remove. WVGA WSVGA WXGA HD WUXGA Customizing the Home Screen 1 Open the home screen category to customize. 2 Select Menu. 3 Select an option:

To rearrange an item, select Rearrange, and select the use. new location. To add an item to the Favorites category, select Add to Favorites, and select the item. To change the home screen background image, select Background, and select an image (Recommended Background Image Dimensions, page 4). Customizing Pages Customizing the Layout of a SmartMode or Combination Page You can customize the layout and data shown in the combination pages and SmartMode layouts. When you change the layout of a page in a display you are interacting with, the change appears only on that display, except for the SmartMode name and symbol. When you change the SmartMode name or symbol for the layout, the new name or symbol appears on all displays in the station. 1 Open a page to customize. 2 Select Menu. 3 Select Edit Layout or Edit Combo. 4 Select an option:

To change the name, select Name or Name & Symbol >

Name, enter a new name, and select Done. To change the SmartMode symbol, select Name &

Symbol > Symbol, and select a new symbol. To change the number of functions shown and the layout of the screen, select Layout, and select an option. To change the function of a portion of the screen, select the window to change, and select a function from the list on the right. To change how the screens are split, drag the arrows to a new location. To change the data shown on the page and additional data bars, select Overlays, and select an option. TIP: While viewing a screen with data overlay, hold an overlay box to quickly change the data in it. To assign a preset to a portion of the SmartMode screen, select Presets > Include, and select a preset from the list on the right. 2 Select an image. Recommended Background Image Dimensions For the best fit for the background image, use an image that has the following dimensions, in pixels. Display resolution Image width Image height 800 1024 1380 1920 1920 430 535 723 991 1111 Customizing the Startup Screen You personalize the image that is displayed when the chartplotter is turning on. For the best fit, the image should be 50 MB or less and conform to the recommended dimensions

(Recommended Startup Image Dimensions, page 4). 1 Insert a memory card that contains the image you want to 2 Select Settings > System > Sounds and Display > Startup Image > Select Image. 3 Select the memory card slot. 4 Select the image. 5 Select Set as Startup Image. The new image is shown then turning on the chartplotter. Recommended Startup Image Dimensions For the best fit for the startup images, use an image that has the following dimensions, in pixels. Display resolution Image width Image height WVGA WSVGA WXGA HD WUXGA 680 880 1080 1240 1700 200 270 350 450 650 Adding a SmartMode Layout You can add SmartMode layouts to suit your needs. Each customization made to one SmartMode layout for the home screen in a station appears on all displays in the station. 1 From the home screen, select SmartMode > Menu > Add Layout. 2 Select an option:

To change the name, select Name & Symbol > Name, enter a new name, and select Done. To change the SmartMode symbol, select Name &

Symbol > Symbol, and select a new symbol. To change the number of functions shown and the layout of the screen, select Layout, and select an option. To change the function of a portion of the screen, select the window to change, and select a function from the list on the right. To change how the screens are split, drag the arrows to a new location. To change the data shown on the page and additional data bars, select Overlays, and select an option. To assign a preset to a portion of the SmartMode screen, select Presets > Include, and select a preset from the list on the right. 4 Customizing the Chartplotter Creating a New Combination Page You can create a custom combination page to suit your needs. 1 Select Combos > Menu > Add Combo. 2 Select a window. 3 Select a function for the window. 4 Repeat these steps for each window of the page. 5 Drag the arrows to resize the windows. 6 Hold a window to rearrange it. 7 Hold a data field to select new data. 8 Select Layout, and select a layout. 9 Select Name, enter a name for the page, and select Done. 10Select Overlays, and select which data to show. 11Select Done when you have finished customizing the page. Deleting a Combination Page 1 Select Combos > Menu > Delete Combo. 2 Select a combination. Customizing the Data Overlays You can customize the data in the data overlays shown on a screen. 1 Select an option based on the type of screen you are viewing:

From a full screen view, select Menu > Edit Overlays. From a combination screen, select Menu > Edit Combo >

From a SmartMode screen, select Menu > Edit Layout >

Overlays. Overlays. TIP: To quickly change the data shown in an overlay box, hold the overlay box. 2 Select an item to customize the data and data bar:

To change the data shown in an overlay box, select the overlay box, select the new data to show, and select Back. To select the location and layout of the data overlay bar, select Data, and select an option. To customize the information shown when navigating, select Navigation, and select an option. To turn on other data bars, like the media controls, select Top Bar or Bottom Bar, and select the necessary options. 3 Select Done. Customizing the Chartplotter Resetting the Station Layouts You can restore the layouts in this station to the factory default settings. Select Settings > System > Station Information > Reset Layouts. Presets A preset is a collection of settings that optimize the screen or view. You can use particular presets to optimize groups of settings for your activity. For example, some settings might be optimal for when you are fishing, and others might be optimal for when you are cruising. Presets are available on some screens, such as charts, sonar views, and radar views. To select a preset for a compatible screen, select Menu >

and select the preset. When you are using a preset and you make changes to the settings or view, you can save the changes to the preset or create a new preset based on the new customizations.

, Saving a New Preset After you have customized the settings and view of a screen, you can save the customization as a new preset. 1 From a compatible screen, change the settings and view. 2 Select Menu >

3 Enter a name, and select Done. 4 Select an item, and select Include to include or exclude the

> Save > New. item from the preset. Managing Presets You can customize the pre-loaded presets and edit presets you created. 1 From a compatible screen, select Menu >

2 Select a preset. 3 Select an option:

> Manage. To rename the preset, select Rename, enter a name, and select Done. To edit the preset, select Edit, and update the preset. To delete the preset, select Delete. To reset all presets to factory settings, select Reset All. Setting the Vessel Type You can select your boat type to configure the chartplotter settings and to use features customized for your boat type. 1 Select Settings > My Vessel > Vessel Type. 2 Select an option. Adjusting the Backlight 1 Select Settings > System > Display > Backlight. 2 Adjust the backlight. TIP: From any screen, press the brightness levels. This can be helpful when the brightness is so low you cannot see the screen. repeatedly to scroll through Adjusting the Color Mode 1 Select Settings > System > Sounds and Display > Color

> Color Mode from any screen to access the Mode. TIP: Select color settings. 2 Select an option. Turning On the Chartplotter Automatically You can set the chartplotter to turn on automatically when the power is applied. Otherwise, you must turn on the chartplotter by pressing

. 5 Select Settings > System > Auto Power Up. NOTE: When Auto Power Up is On, and the chartplotter is turned off using within less than two minutes, you may need to press restart the chartplotter.

, and power is removed and reapplied to Enabling Screen Lock For anti-theft protection and to prevent unauthorized use of your device, you can enable the Screen Lock feature which requires a PIN (Personal Identification Number). When enabled, you must enter the PIN to unlock the screen each time you turn on the device. You can set up recovery questions and answers as prompts in case you forget the PIN. NOTICE If you enable the Screen Lock feature, Garmin Support cannot retrieve the PIN or access your device. It is your responsibility to provide the PIN to anyone authorized to use the vessel. 1 Select Settings > System > Sounds and Display > Screen Lock > Setup. 2 Enter a memorable numeric PIN of 6 digits. 3 Reenter the PIN to verify. 4 When prompted, choose and answer three PIN recovery questions. You can Disable or Reset the PIN and recovery questions as needed. Automatically Turning Off the System You can set the chartplotter and the whole system to turn off automatically after it has been asleep for the selected length of time. Otherwise, you must press and hold system manually. 1 Select Settings > System > Auto Power Off. 2 Select an option. to turn off the Feature Automatically transfer Garmin Quickdraw contours you have downloaded or created Push smart notifications Automatically transfer user data, such as waypoints and routes Begin navigating to a specific waypoint or navigating a specific route, and send that waypoint or route to the GPSMAP device Owner Guest Yes No Yes Yes Yes No Yes Yes Getting Started with the ActiveCaptain App You can connect a mobile device to the GPSMAP device using the ActiveCaptain app. The app provides a quick and easy way for you to interact with your GPSMAP device and complete such tasks as sharing data, registering, updating the device software, and receiving mobile device notifications. 1 From the GPSMAP device, select A/V, Gauges, Controls >

2 From the ActiveCaptain page, select Wi-Fi Network > Wi-Fi ActiveCaptain.

> On. 3 Enter a name and password for this network. 4 Insert a memory card in the GPSMAP device's card slot

(Memory Cards, page 2). 5 Select Set ActiveCaptain Card. NOTICE You might be prompted to format the memory card. Formatting the card deletes all information saved on the card. This includes any saved user data, such as waypoints. Formatting the card is recommended, but not required. Before formatting the card, you should save the data from the memory card onto the device internal memory (Copying User Data from a Memory Card, page 64). After formatting the card for the ActiveCaptain app, you can transfer the user data back to the card (Copying User Data to a Memory Card, page 64). ActiveCaptain App Be sure the card is inserted each time you want to use the ActiveCaptain feature. CAUTION 6 From the application store on your mobile device, install and This feature allows users to submit information. Garmin makes no representations about the accuracy, completeness, or timeliness of information submitted by users. Any use or reliance on the information submitted by users is at your own risk. device. The ActiveCaptain app provides a connection to your GPSMAP device, charts, maps, and the community for a connected boating experience. On your mobile device with the ActiveCaptain app, you can download, purchase, and update maps and charts. You can use the app to easily and quickly transfer user data, such as waypoints and routes, connect to the Garmin Quickdraw Contours Community, update device software, and plan your trip. You can connect to the ActiveCaptain community for up-to-date feedback on marinas and other points of interest. The app can push smart notifications, such as calls and texts, to your chartplotter display when paired. ActiveCaptain Roles Your level of interaction with the GPSMAP device using the ActiveCaptain app depends on your role. Feature Update software Register device, built-in maps, and supplemental map cards to account Owner Guest Yes No open the ActiveCaptain app. 7 Bring the mobile device within 32 m (105 ft.) of the GPSMAP 8 From your mobile device settings, open the WiFi connections page and connect to the Garmin device, using the name and password you entered in the Garmin device. Enabling Smart Notifications WARNING Do not read or reply to notifications while operating the vessel. Failure to pay attention to the conditions on the water can result in vessel damage, personal injury, or death. Before your GPSMAP device can receive notifications, you must connect it to your mobile device and to the ActiveCaptain app. 1 From the GPSMAP device, select ActiveCaptain > Smart Notifications > Enable Notifications. 2 Turn on Bluetooth technology in the mobile device settings. 3 Bring the devices within 10 m (33 ft.) of each other. 4 From the ActiveCaptain app on the mobile device, select Smart Notifications > Pair with Chartplotter. 5 Follow the on-screen instructions to pair the app to the GPSMAP device. Yes Yes 6 When prompted, enter the key on your mobile device. 6 ActiveCaptain App 7 If necessary, adjust which notifications you receive in your To turn off pop-up notifications and disable access to the messages list on this chartplotter, select Visibility. mobile device settings. Receiving Notifications WARNING Do not read or reply to notifications while operating the vessel. Failure to pay attention to the conditions on the water can result in vessel damage, personal injury, or death. Before your GPSMAP device can receive notifications, you must connect it to your mobile device and enable the Smart Notifications feature (Enabling Smart Notifications, page 6). When the Smart Notifications feature is enabled and your mobile device receives a notification, a pop-up notification appears on the GPSMAP screen briefly. NOTE: The available actions depend on the type of notification and your phone operating system. To answer a phone call on your phone, select Answer. TIP: Have your phone nearby. The phone call is answered on your mobile phone, not on the chartplotter. To not answer the phone call, select Decline. To review the full message, select Review. To dismiss the pop-up notification, select OK or wait for the notification to close automatically. To remove the notification from the chartplotter and your mobile device, select Clear. Managing Notifications WARNING Do not read or reply to notifications while operating the vessel. Failure to pay attention to the conditions on the water can result in vessel damage, personal injury, or death. Before you can manage the notifications, you must enable the Smart Notifications feature (Enabling Smart Notifications, page 6). When the Smart Notifications feature is enabled and your mobile device receives a notification, a pop-up notification appears on the GPSMAP screen briefly. You can access and manage the notifications from the ActiveCaptain screen. 1 Select ActiveCaptain > Smart Notifications > Messages. A list of notifications appear. 2 Select a notification. 3 Select an option:

NOTE: The available options vary based on your mobile device and the notification type. To dismiss and remove the notification from the chartplotter and your mobile device, select Clear or Delete. NOTE: This does not delete the message from the mobile device. This only dismisses and removes the notification. To call the phone number back, select Call Back or Dial. Making Notifications Private You can turn off the pop-up notifications and disable the messages list on specific chartplotters for privacy. For example, the captain could disable pop-up notifications and messages on the chartplotter used for fishing, but allow notifications on the chartplotter used at the helm. 1 From the chartplotter you want notifications to be private, select ActiveCaptain > Smart Notifications. 2 Select an option:

Popups. To turn off pop-up notifications on this chartplotter, select Updating Software with the ActiveCaptain App If your device has WiFi technology, you can use the ActiveCaptain app to download and install the latest software updates for your device. NOTICE Software updates may require the app to download large files. Regular data limits or charges from your Internet service provider apply. Contact your Internet service provider for more information about data limits or charges. The installation process can take several minutes. 1 Connect the mobile device to the GPSMAP device (Getting Started with the ActiveCaptain App, page 6). 2 When a software update is available and you have internet access on your mobile device, select Software Updates >

Download. The ActiveCaptain app downloads the update to the mobile device. When you reconnect the app to the GPSMAP device, the update is transferred to the device. After the transfer is complete, you are prompted to install the update. 3 When you are prompted by the GPSMAP device, select an option to install the update. To update the software immediately, select OK. To delay the update, select Cancel. When you are ready to install the update, select ActiveCaptain > Software Updates > Install Now. Updating Charts with ActiveCaptain You can use the ActiveCaptain app to download and transfer the latest chart updates for your device. To save space on your mobile device, space on the ActiveCaptain card, and download time, consider using the ActiveCaptain app to download only the areas of the chart you need. If you are downloading an entire chart, you can use the Garmin Express app to download the map onto a memory card

(Updating Your Charts Using the Garmin Express App, page 65). The Garmin Express app downloads large charts more quickly than the ActiveCaptain app. NOTICE Chart updates may require the app to download large files. Regular data limits or charges from your internet service provider apply. Contact your internet service provider for more information about data limits or charges. 1 Connect the mobile device to the GPSMAP device (Getting Started with the ActiveCaptain App, page 6). 2 When a chart update is available, and you have internet access on your mobile device, select OneChart > My Charts. 3 Select the map to update. 4 Select the area to download. 5 Select Download. The ActiveCaptain app downloads the update to the mobile device. When you reconnect the app to the GPSMAP device, the update is transferred to the device. After the transfer is complete, the updated charts are available for use. Communication with Wireless Devices The chartplotters can create a wireless network to which you can connect wireless devices. Communication with Wireless Devices 7 Connecting wireless devices allows you to use Garmin apps, such as ActiveCaptain. WiFi Network Setting Up the WiFi Wireless Network The chartplotters can create a WiFi network to which you can connect wireless devices. The first time you access the wireless network settings, you are prompted to set up the network. 1 Select Settings > Communications > Wi-Fi Network > Wi-

Fi > On > OK. 2 If necessary, enter a name for this wireless network. 3 Enter a password. You will need this password to access the wireless network from a wireless device. The password is case-sensitive. Connecting a Wireless Device to the Chartplotter Before you can connect a wireless device to the chartplotter wireless network, you must configure the chartplotter wireless network (Setting Up the WiFi Wireless Network, page 8). You can connect multiple wireless devices to the chartplotter to share data. 1 From the wireless device, turn on the WiFi technology and search for wireless networks. 2 Select the name of your chartplotter wireless network (Setting Up the WiFi Wireless Network, page 8). 3 Enter the chartplotter password. Changing the Wireless Channel You can change the wireless channel if you have trouble finding or connecting to a device, or if you experience interference. 1 Select Settings > Communications > Wi-Fi Network >

Advanced > Channel. 2 Enter a new channel. You do not need to change the wireless channel of devices connected to this network. Changing the WiFi Host If there are multiple chartplotters with WiFi technology on the Garmin marine network, you can change which chartplotter is the WiFi host. This can be helpful if you are having trouble with WiFi communications. Changing the WiFi host allows you to select a chartplotter that is physically closer to your mobile device. 1 Select Settings > Communications > Wi-Fi Network >

Advanced > Wi-Fi Host. 2 Follow the on-screen instructions. Wireless Remote Control These steps are not applicable to the GRID remote input devices (Pairing the GRID Device with the Chartplotter from the Chartplotter, page 66). Pairing the Wireless Remote Control With the Chartplotter Before you can use the wireless remote control with a chartplotter, you must pair the remote with the chartplotter. You can connect a single remote to multiple plotters, and then press the pairing key to switch between the chartplotters. 1 Select Settings > Communications > Wireless Devices >

Wireless Remotes > GPSMAP Remote. 2 Select New Connection. 3 Follow the on-screen instructions. Turning On and Off the Remote Backlight Turning off the remote backlight can significantly increase the battery life. 1 On the chartplotter, select Settings > Communications >

Wireless Devices > Wireless Remotes > GPSMAP Remote > Backlight. 2 Follow the on-screen instructions. Disconnecting the Remote from All Chartplotters 1 On the chartplotter, select Settings > Communications >

Wireless Devices > Wireless Remotes > GPSMAP Remote > Disconnect All. 2 Follow the on-screen instructions. Wireless Wind Sensor Connecting a Wireless Sensor to the Chartplotter You can view data from a compatible wireless sensor on the chartplotter. 1 Select Settings > Communications > Wireless Devices. 2 Select the wind sensor. 3 Select Enable. The chartplotter begins searching for and connecting to the wireless sensor. To view data from the sensor, add the data to a data field or gauge. Adjusting the Wind Sensor Orientation You should adjust this setting if the sensor does not face the front of the boat, exactly parallel to the center line. NOTE: The opening where the cable connects to the pole indicates the front of the sensor. 1 Estimate the angle, in degrees clockwise around the mast, by which the sensor points away from the center of the front of the boat:

If the sensor is facing starboard, the angle should be between 1 and 180 degrees. If the sensor is facing port, the angle should be between

-1 and -180 degrees. 2 Select Settings > Communications > Wireless Devices. 3 Select the wind sensor. 4 Select Wind Angle Offset. 5 Enter the angle observed in step 1. 6 Select Done. Viewing Boat Data on a Garmin Watch You can connect a compatible Garmin watch to a compatible chartplotter to view data from the chartplotter. 1 Bring the Garmin watch within range (3 m) of the chartplotter. 2 From the watch clock screen, select START > Boat Data >

START. NOTE: If you have already connected to a chartplotter, and would like to connect to a different chartplotter, open the Boat Data screen, hold UP, and select Pair new. 3 On the chartplotter, select Communications > Wireless Devices > Connect IQ Apps > Boat Data > Enable >

New Connection. The chartplotter begins searching for and connecting to the wearable device. 4 Compare the code shown on the chartplotter with the one 5 If the codes match, select Yes to complete the pairing shown on the watch. process. After the devices are paired, they connect automatically when they are turned on and within range. 8 Communication with Wireless Devices Viewing Boat Data on a Garmin Nautix Device You can connect a Garmin Nautix device to the chartplotter to view charplotter data on the Garmin Nautix device. NOTE: You can connect a Garmin Nautix device to multiple compatible devices for better coverage on larger vessels. 1 Bring the a Garmin Nautix device within range (3 m) of the chartplotter. The device automatically looks for all compatible devices within range. 2 If necessary, from the wearable device menu, select Device Connections > Pair New Device. 3 On the chartplotter, select Settings > Communications >

Wireless Devices > Connect IQ Apps > Boat Data >

Enable Connections > New Connection. The chartplotter begins searching for and connecting to the wearable device. After the devices are paired, they connect automatically when they are turned on and within range. Charts and 3D Chart Views The charts and 3D chart views that are available depend on the map data and accessories used. NOTE: 3D chart views are available with premium charts, in some areas. You can access the charts and 3D chart views by selecting Charts. Nav. Chart: Shows navigation data available on your pre-loaded maps and from supplemental maps, if available. The data includes buoys, lights, cables, depth soundings, marinas, and tide stations in an overhead view. Fishing Chart: Provides a detailed view of the bottom contours and depth soundings on the chart. This chart removes navigational data from the chart, provides detailed bathymetric data, and enhances bottom contours for depth recognition. This chart is best for offshore deep-sea fishing. NOTE: The Fishing chart is available with premium charts, in some areas. Perspective 3D: Provides a view from above and behind the boat (according to your course) and provides a visual navigation aid. This view is helpful when navigating tricky shoals, reefs, bridges, or channels, and is beneficial when trying to identify entry and exit routes in unfamiliar harbors or anchorages. 3D Chart: Shows a detailed, three-dimensional view from above and behind the boat (according to your course) and provides a visual navigation aid. This view is helpful when navigating tricky shoals, reefs, bridges, or channels, and when trying to identify entry and exit routes in unfamiliar harbors or anchorages. Fish Eye 3D: Provides an underwater view that visually represents the sea floor according to the chart information. When a sonar transducer is connected, suspended targets

(such as fish) are indicated by red, green, and yellow spheres. Red indicates the largest targets and green indicates the smallest. Relief Shading: Provides high resolution elevation shading of lakes and coastal waters. This chart can be helpful for fishing and diving. NOTE: The Relief Shading chart is available with premium charts, in some areas. Navigation Chart and Fishing Chart NOTE: The Fishing chart is available with premium charts, in some areas. The Nav. Chart is optimized for navigation. You can plan a course, view map information, and use the chart as a navigational aid. To open the Nav. Chart, select Charts > Nav. Chart. The Fishing Chart provides a detailed view with more bottom detail and fishing content. This chart is optimized for use when fishing. To open the Fishing Chart, select Charts > Fishing Chart. Zooming In and Out Using the Touchscreen You can quickly zoom in and out of many screens, such as the charts and sonar views. Pinch two fingers together to zoom out. Spread two fingers apart to zoom in. Chart Symbols This table contains some of the common symbols you might see on the detailed charts. Icon Description Buoy Information Marine services Tide station Current station Overhead photo available Perspective photo available Other features common to most charts include depth contour lines, intertidal zones, spot soundings (as depicted on the original paper chart), navigational aids and symbols, obstructions, and cable areas. Measuring a Distance on the Chart 1 From a chart, select a location. 2 Select Measure. A push pin appears on the screen at your present location. The distance and angle from the pin is listed in the corner. TIP: To reset the pin and measure from the current location of the cursor, select Set Reference. Creating a Waypoint on the Chart 1 From a chart, select a location or object. 2 Select

. Viewing Location and Object Information on a Chart You can view information, such as tide, current, celestial, chart notes, or local services, about a location or an object on the Navigation chart or the Fishing chart. 1 From the Navigation chart or Fishing chart, select a location or object. A list of options appears along the top of the chart. The options that appear vary based on the location or object you selected. 2 If necessary, select

. Charts and 3D Chart Views 9 3 Select Information. Viewing Details about Navaids From the Navigation chart, Fishing chart, Perspective 3D chart view, or Mariners Eye 3D chart view, you can view details about various types of navigation aids, including beacons, lights, and obstructions. NOTE: The Fishing chart is available with premium charts, in some areas. NOTE: 3D chart views are available with premium charts, in some areas. 1 From a chart or 3D chart view, select a navaid. 2 Select the name of the navaid. Navigating to a Point on the Chart WARNING All route and navigation lines displayed on the chartplotter are only intended to provide general route guidance or to identify proper channels, and are not intended to be precisely followed. Always defer to the navaids and conditions on the water when navigating to avoid groundings or hazards that could result in vessel damage, personal injury, or death. The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects. NOTE: The Fishing chart is available with premium charts, in some areas. NOTE: Auto Guidance is available with premium charts, in some areas. 1 From the Navigation chart or Fishing chart, select a location. 2 If necessary, select Navigate To. 3 Select an option:

To navigate directly to the location, select Go To or

. To create a route to the location, including turns, select Route To or

. To use Auto Guidance, select Auto Guidance or

. 4 Review the course indicated by the magenta line. NOTE: When using Auto Guidance, a gray segment within any part of the magenta line indicates that Auto Guidance cannot calculate part of the Auto Guidance line. This is due to the settings for minimum safe water depth and minimum safe obstacle height. 5 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. Premium Charts NOTE: Not all models support all charts. Optional premium charts, such as BlueChart g3 Vision, allow you to get the most out of your chartplotter. In addition to detailed marine charting, premium charts may contain these features, which are available in some areas. Mariners Eye 3D: Provides a view from above and behind the boat for a three-dimensional navigation aid. Fish Eye 3D: Provides an underwater, three-dimensional view that visually represents the sea floor according to the information on the chart. Fishing Charts: Shows the chart with enhanced bottom contours and without navigational data. This chart works well for offshore deep-sea fishing. High Resolution Satellite Imagery: Provides high-resolution satellite images for a realistic view of the land and water on the Navigation chart (Showing Satellite Imagery on the Navigation Chart, page 11). Aerial Photos: Shows marinas and other navigationally significant aerial photos to help you visualize your surroundings (Viewing Aerial Photos of Landmarks, page 11). Detailed Roads and POI data: Shows detailed road and point of interest (POI) data, which includes highly detailed coastal roads and POIs such as restaurants, lodging, and local attractions. Auto Guidance: Uses specified information about your vessel and chart data to determine the best path to your destination. Fish Eye 3D Chart View Using the depth contour lines of the premium charts, such as BlueChart g3 Vision, the Fish Eye 3D chart view provides an underwater view of the sea floor or lake bottom. Suspended targets, such as fish, are indicated by red, green, and yellow spheres. Red indicates the largest targets and green indicates the smallest. icon on the chart indicates a tide station. You can view a Viewing Tide Station Information The detailed graph for a tide station to help predict the tide level at different times or on different days. NOTE: This feature is available with premium charts, in some areas. 1 From the Navigation chart or Fishing chart, select a tide station. Tide direction and tide level information appear near

. WARNING 2 Select the station name. All route and navigation lines displayed on the chartplotter are only intended to provide general route guidance or to identify proper channels, and are not intended to be precisely followed. Always defer to the navaids and conditions on the water when navigating to avoid groundings or hazards that could result in vessel damage, personal injury, or death. The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. Animated Tide and Current Indicators NOTE: This feature is available with premium charts, in some areas. You can view indicators for animated tide station and current direction on the Navigation chart or the Fishing chart. You must also enable animated icons in the chart settings (Showing Tides and Current Indicators, page 11). An indicator for a tide station appears on the chart as a vertical bar graph with an arrow. A red arrow pointing downward indicates a falling tide, and a blue arrow pointing upward indicates a rising tide. When you move the cursor over the tide 10 Charts and 3D Chart Views station indicator, the height of the tide at the station appears above the station indicator. Current direction indicators appear as arrows on the chart. The direction of each arrow indicates the direction of the current at a specific location on the chart. The color of the current arrow indicates the range of speed for the current at that location. When you move the cursor over the current direction indicator, the specific current speed at the location appears above the direction indicator. Color Yellow Orange Red Current Speed Range 0 to 1 knot 1 to 2 knots 2 or more knots Showing Tides and Current Indicators NOTE: This feature is available with premium charts, in some areas. You can show static or animated tide and current station indicators on the Navigation chart or Fishing chart. 1 From the Navigation or Fishing chart, select Menu > Layers

> Chart > Tides & Currents. 2 Select an option:

To show animated tide station indicators and animated current direction indicators on the chart, select Animated. To enables the tides and current slider, which sets the time for which tides and currents are reported on the map, select Slider. Showing Satellite Imagery on the Navigation Chart NOTE: This feature is available with premium charts, in some areas. You can overlay high-resolution satellite images on the land or on both land and sea portions of the Navigation chart. NOTE: When enabled, high-resolution satellite images are present only at lower zoom levels. If you cannot see high-

resolution images in your optional chart region, you can select to zoom in. You also can set the detail level higher by changing the map zoom detail. 1 From the Navigation chart, select Menu > Layers > Chart >

Satellite Photos. 2 Select an option:

Select Land Only to show standard chart information on the water, with photos overlaying the land. NOTE: This setting must be enabled to view Standard Mapping charts. Select Photo Map to show photos on both the water and the land at a specified opacity. Use the slider bar to adjust the photo opacity. The higher you set the percentage, the more the satellite photos cover both land and water. Viewing Aerial Photos of Landmarks Before you can view aerial photos on the Navigation chart, you must turn on the Photo Points setting in the chart setup. NOTE: This feature is available with premium charts, in some areas. You can use aerial photographs of landmarks, marinas, and harbors to help orient yourself to your surroundings or to acquaint yourself with a marina or a harbor prior to arrival. 1 From the Navigation chart, select a camera icon:

To view an overhead photo, select To view a perspective photo, select

. The photo was taken from the location of the camera, pointed in the direction of the cone. 2 Select Photo. Charts and 3D Chart Views Automatic Identification System The Automatic Identification System (AIS) enables you to identify and track other vessels, and alerts you to area traffic. When connected to an external AIS device, the chartplotter can show some AIS information about other vessels that are within range, that are equipped with a transponder, and that are actively transmitting AIS information. The information reported for each vessel includes the Maritime Mobile Service Identity (MMSI), location, GPS speed, GPS heading, time that has elapsed since the last position of the vessel was reported, nearest approach, and time to the nearest approach. Some chartplotter models also support Blue Force Tracking. Vessels being tracked with Blue Force Tracking are indicated on the chartplotter with a blue-green color. AIS Targeting Symbols Symbol Description AIS vessel. The vessel is reporting AIS information. The direction in which the triangle is pointing indicates the direction in which the AIS vessel is moving. Target is selected. Target is activated. The target appears larger on the chart. A green line attached to the target indicates the heading of the target. The MMSI, speed, and direction of the vessel appear beneath the target, if the details setting has been set to Show. If the AIS transmission from the vessel is lost, a message banner appears. Target is lost. A green X indicates that the AIS transmission from the vessel is lost, and the chartplotter displays a message banner asking whether the vessel should continue to be tracked. If you discontinue vessel tracking, the lost target symbol disappears from the chart or the 3D chart view. Dangerous target in range. The target flashes while an alarm sounds and a message banner appears. After the alarm has been acknowledged, a solid red triangle with a red line attached to it indicates the location and the heading of the target. If the safe-zone collision alarm has been set to Off, the target flashes, but the audible alarm does not sound and the alarm banner does not appear. If the AIS transmission from the vessel is lost, a message banner appears. Dangerous target is lost. A red X indicates that the AIS transmission from the vessel is lost, and the chartplotter displays a message banner asking whether the vessel should continue to be tracked. If you discontinue vessel tracking, the lost dangerous target symbol disappears from the chart or the 3D chart view. The location of this symbol indicates the closest point of approach to a dangerous target, and the numbers near the symbol indicate the time to the closest point of approach to that target. NOTE: Vessels being tracked with the Blue Force Tracking feature are indicated with a blue-green color regardless of their status. Heading and Projected Course of Activated AIS Targets When heading and course over ground information are provided by an activated AIS target, the heading of the target appears on a chart as a solid line attached to the AIS target symbol. A heading line does not appear on a 3D chart view. The projected course of an activated AIS target appears as a dashed line on a chart or a 3D chart view. The length of the projected course line is based on the value of the projected heading setting. If an activated AIS target is not transmitting speed information, or if the vessel is not moving, a projected course line does not appear. Changes in the speed, course over ground, or rate of turn information transmitted by the vessel can impact the calculation of the projected course line. 11 When course over ground, heading, and rate of turn information are provided by an activated AIS target, the projected course of the target is calculated based on the course over ground and the rate of turn information. The direction in which the target is turning, which is also based on the rate of turn information, is indicated by the direction of the barb at the end of the heading line. The length of the barb does not change. sent from another location. Virtual ATONs do not actually exist, and their identifying and location information is sent from another location. You can view AIS ATONs on the chart when the chartplotter is connected to a compatible AIS radio. To show AIS ATONs, from a chart, select Menu > Layers > Chart > Navaid > ATONs. You can view more information about an ATON if you select the ATON on the chart. Symbol Meaning Real or synthetic ATON When course over ground and heading information are provided by an activated AIS target, but rate of turn information is not provided, the projected course of the target is calculated based on the course over ground information. Activating a Target for an AIS Vessel 1 From a chart or a 3D chart view, select an AIS vessel. 2 Select AIS Vessel > Activate Target. Viewing Information about a Targeted AIS Vessel You can view the AIS signal status, MMSI, GPS speed, GPS heading, and other information that is reported about a targeted AIS vessel. 1 From a chart or a 3D chart view, select an AIS vessel. 2 Select AIS Vessel. Deactivating a Target for an AIS Vessel 1 From a chart or a 3D chart view, select an AIS vessel. 2 Select AIS Vessel > Deactivate. Viewing a List of AIS and MARPA Threats 1 From a chart, select Menu > Layers > Other Vessels > List

> Show. 2 Select the type of threats to include in the list. Setting the Safe-Zone Collision Alarm Before you can set a collision alarm, you must have a compatible chartplotter connected to an AIS device or radar. The safe-zone collision alarm is used only with AIS and MARPA. MARPA functionality works with radar. The safe zone is used for collision avoidance and can be customized. 1 Select Settings > Alarms > Collision Alarm > On. A message banner appears and an alarm sounds when a MARPA-tagged object or an AIS-activated vessel enters the safe-zone area around your boat. The object is also labeled as dangerous on the screen. When the alarm is off, the message banner and audible alarm are disabled, but the object is still labeled as dangerous on the screen. 2 Select Range, and select a distance for the safe-zone radius around your vessel. 3 Select Time To, and select a time at which the alarm will sound if a target is determined to intersect the safe zone. For example, to be notified of a pending intersection 10 minutes before it will likely occur, set Time To to 10, and the alarm will sound 10 minutes before the vessel intersects the safe zone. 4 Select MARPA Alarm, and select an option for when the alarm sounds for MARPA-tagged objects. AIS Aids to Navigation An AIS aid to navigation (ATON) is any kind of navigational aid that is transmitted over the AIS radio. ATONs are displayed on the charts and have identifying information, such as position and type. There are three main kinds of AIS ATONs. Real ATONs physically exist and send their identifying and location information from their actual location. Synthetic ATONs physically exist, and their identifying and location information is Real or synthetic ATON: Topmark North Real or synthetic ATON: Topmark South Real or synthetic ATON: Topmark East Real or synthetic ATON: Topmark West Real or synthetic ATON: Topmark Special Real or synthetic ATON: Topmark Safe Real or synthetic ATON: Topmark Danger Virtual ATON Virtual ATON: Topmark North Virtual ATON: Topmark South Virtual ATON: Topmark East Virtual ATON: Topmark West Virtual ATON: Topmark Special Virtual ATON: Topmark Safe Virtual ATON: Topmark Danger AIS Distress Signals Self-contained AIS distress signal devices transmit emergency position reports when activated. The chartplotter can receive signals from Search and Rescue Transmitters (SART), Emergency Position Indicating Radio Beacons (EPIRB), and other man overboard signals. Distress signal transmissions are different than standard AIS transmissions, so they appear differently on the chartplotter. Instead of tracking a distress signal transmission for collision avoidance, you track a distress signal transmission to locate and assist a vessel or person. Navigating to a Distress Signal Transmission When you receive a distress signal transmission, a distress signal alarm appears. Select Review > Go To to begin navigation to the transmission. AIS Distress Signal Device Targeting Symbols Symbol Description AIS distress signal device transmission. Select to see more information about the transmission and begin navigation. Transmission lost. Transmission test. Appears when a vessel initiates a test of their distress signal device, and does not represent a true emergency. Transmission test lost. Enabling AIS Transmission Test Alerts To avoid a large number of test alerts and symbols in crowded areas such as marinas, you can select to receive or ignore AIS test messages. To test an AIS emergency device, you must enable the chartplotter to receive test alerts. 1 Select Settings > Alarms > AIS. 12 Charts and 3D Chart Views 2 Select an option:

To receive or ignore Emergency Position Indicating Radio Beacon (EPRIB) test signals, select AIS-EPIRB Test. To receive or ignore Man Overboard (MOB) test signals, select AIS-MOB Test. To receive or ignore Search and Rescue Transponder

(SART) test signals, select AIS-SART Test. Turning Off AIS Reception AIS signal reception is turned on by default. Select Settings > Other Vessels > AIS > Off. All AIS functionality on all charts and 3D chart views is disabled. This includes AIS vessel targeting and tracking, collision alarms that result from AIS vessel targeting and tracking, and the display of information about AIS vessels. Chart Menu NOTE: Not all settings apply to all charts. Some options require premium maps or connected accessories, such as radar. NOTE: The menus may contain some settings that are not supported by your installed charts or your present location. If you make changes to those settings, the changes will not impact the chart view. From a chart, select Menu. Layers: Adjusts the appearance of the different items on the charts (Chart Layers, page 13). Quickdraw Contours: Turns on bottom contour drawing, and allows you to create fishing map labels (Garmin Quickdraw Contours Mapping, page 15). Settings: Adjusts the chart settings (Chart Settings, page 15). Edit Overlays: Adjusts the data shown on the screen

(Customizing the Data Overlays, page 5). Chart Layers You can turn on and off chart layers and customize features of the charts. Each setting is specific to the chart or chart view being used. NOTE: Not all settings apply to all charts and chartplotter models. Some options require premium maps or connected accessories. NOTE: The menus may contain some settings that are not supported by your installed charts or your present location. If you make changes to those settings, the changes will not impact the chart view. From a chart, select Menu > Layers. Chart: Shows and hides chart-related items (Chart Layer Settings, page 13). My Vessel: Shows and hides items relating to the boat (My Vessel Layer Settings, page 13). User Data: Shows and hides user data, such as waypoints, boundaries, and tracks, and opens user data lists (User Data Layer Settings, page 14). Other Vessels: Adjusts how other vessels are shown (Other Vessels Layer Settings, page 14). Water: Shows and hides depth items (Water Layer Settings, page 14). Quickdraw Contours: Shows and hides Garmin Quickdraw Contours data (Garmin Quickdraw Contours Settings, page 16). Weather: Shows and hides weather-related items (Weather Layer Settings, page 14). Chart Layer Settings From a chart, select Menu > Layers > Chart. Satellite Photos: Shows high-resolution satellite images on the land or on both land and sea portions of the Navigation chart, when certain premium maps are used (Showing Satellite Imagery on the Navigation Chart, page 11). NOTE: This setting must be enabled to view Standard Mapping charts. Tides & Currents: Shows current station indicators and tide station indicators on the chart (Showing Tides and Current Indicators, page 11) and enables the tides and current slider, which sets the time for which tides and currents are reported on the map. Land POIs: Shows points of interest on land. Navaid: Shows navigational aids, such as ATONs and flashing lights, on the chart. Allows you to select NOAA or IALA navaid type. Service Points: Shows locations for marine services. Depth: Adjusts the items on the depth layer (Depth Layer Restricted Areas: Shows information about restricted areas on Settings, page 13). the chart. Photo Points: Shows camera icons for aerial photos (Viewing Aerial Photos of Landmarks, page 11). Depth Layer Settings From a chart, select Menu > Layers > Chart > Depth. Depth Shading: Specifies an upper and lower depth to shade Shallow Shading: Sets the shades from the shoreline to the between. specified depth. Spot Depths: Turns on spot soundings and sets a dangerous depth. Spot depths that are equal to or more shallow than the dangerous depth are indicated by red text. Fishing Contours: Sets the zoom level for a detailed view of bottom contours and depth soundings and simplifies map presentation for optimal use while fishing. My Vessel Layer Settings From a chart, select Menu > Layers > My Vessel. Heading Line: Shows and adjusts the heading line, which is a line drawn on the map from the bow of the boat in the direction of travel (Setting the Heading Line and Angle Markers, page 25). Active Tracks: Shows the active track on the chart and opens the Active Track Options menu. Wind Rose: Shows a visual representation of the wind angle or direction provided by the connected wind sensor and sets the wind source. Compass Rose: Shows a compass rose around your boat, indicating compass direction oriented to the heading of the boat. Enabling this option disables the Wind Rose option. Vessel Icon: Sets the icon that represents your present location on the chart. Laylines Settings To use the laylines features, you must connect a wind sensor to the chartplotter. When in sailing mode (Setting the Vessel Type, page 5), you can display laylines on the navigation chart. Laylines can be very helpful when racing. Charts and 3D Chart Views 13 NOTE: Not all settings apply to all charts, views, and chartplotter models. Some options require premium maps or connected accessories. Depth Shading: Specifies an upper and lower depth to shade Shallow Shading: Sets the shades from the shoreline to the between. specified depth. Spot Depths: Turns on spot soundings and sets a dangerous depth. Spot depths that are equal to or more shallow than the dangerous depth are indicated by red text. Fishing Contours: Sets the zoom level for a detailed view of bottom contours and depth soundings and simplifies map presentation for optimal use while fishing. Relief Shading: Shows the gradient of the bottom with shading. This feature is available only with some premium maps. Sonar Imagery: Shows sonar imagery to help show the density of the bottom. This feature is available only with some premium maps. Lake Level: Sets the present water level of the lake. This feature is available only with some premium maps. Depth Range Shading You can set color ranges on your map to show the water depths where your target fish are currently biting. You can set deeper ranges to monitor how quickly the bottom depth changes within a specific depth range. You can create up to ten depth ranges. For inland fishing, a maximum of five depth ranges can help reduce map clutter. The depth ranges apply to all charts and all bodies of water. Some Garmin LakeV and premium supplemental charts have multiple depth range shading by default. Red Orange Yellow Green From 0 to 1.5 m (from 0 to 5 ft.) From 1.5 to 3 m (from 5 to 10 ft.) From 3 to 4.5 m (from 10 to 15 ft.) From 4.5 to 7.6 m (from 15 to 25 ft.) Weather Layer Settings From the Navigation or Fishing chart, select Menu > Layers >

Chart > Weather >

From a weather chart, select Menu > Layers > Chart >

Weather. Observed Layers: Sets which observed weather items are

. shown. Observed weather is the present weather condition that are visible now. Forecast Layers: Sets which forecasted weather items are Layer Mode: Shows forecasted or observed weather Loop: Shows a loop of forecasted or observed weather Legend: Shows the weather legend, with the severity of the conditions increasing from left to right. Weather Subscription: Shows weather subscription shown. information. information. information. From the navigation chart, select Menu > Layers > My Vessel >

Laylines > Setup. Display: Sets how the laylines and vessel appear on the chart, and sets the length of the laylines. Sailing Ang.: Allows you to select how the device calculates laylines. The Actual option calculates the laylines using the measured wind angle from the wind sensor. The Manual option calculates the laylines using manually entered windward and leeward angles. Windward Ang.: Allows you to set a layline based on the windward sailing angle. Leeward Ang.: Allows you to set a layline based on the leeward sailing angle. Tide Correction: Corrects the laylines based on the tide. Layline Filter: Filters the layline data based on the time interval entered. For a smoother layline that filters out some of the changes in the boat's heading or true wind angle, enter a higher number. For laylines that display a higher sensitivity to changes in the boat's heading or true wind angle, enter a lower number. User Data Layer Settings You can show user data, such as waypoints, boundaries, and tracks, on the charts. From a chart, select Menu > Layers > User Data. Waypoints: Shows waypoints on the chart and opens the list of waypoints. of boundaries. Boundaries: Shows boundaries on the chart and opens the list Tracks: Shows tracks on the chart. Other Vessels Layer Settings NOTE: These options require connected accessories, such as an AIS receiver, radar, or VHF radio. From a chart, select Menu > Layers > Other Vessels. DSC: Sets how DSC vessels and trails appear on the chart, and AIS: Sets how AIS vessels and trails appear on the chart, and shows the DSC list. shows the AIS list. MARPA: Sets how MARPA vessels and trails appear on the chart, and shows the MARPA list. Details: Shows other vessel details on the chart. Proj. Heading: Sets the projected heading time for AIS-

activated and MARPA-tagged vessels. Collision Alarm: Sets the safe-zone collision alarm (Setting the Safe-Zone Collision Alarm, page 12). Water Layer Settings From a chart, select Menu > Layers > Water. NOTE: The menu may contain some settings that are not supported by your installed charts or your present location. If you make changes to those settings, the changes will not impact the chart view. 14 Charts and 3D Chart Views Restore Defaults: Resets the weather settings to factory default values. Edit Overlays: Adjusts the data shown on the screen

(Customizing the Data Overlays, page 5). Radar Overlay Settings From the Navigation or Fishing chart, select Menu > Layers >

Radar >

From a radar screen, select Menu. Radar To Standby: Stops radar transmission. Gain: Adjusts the gain (Adjusting Gain on the Radar Screen Automatically, page 37). Sea Clutter: Adjusts the sea clutter (Adjusting Gain on the Radar Screen Automatically, page 37). Radar Options: Opens the radar options menu (Radar Options Menu, page 38). Other Vessels: Sets how other vessels are displayed on the radar view (Other Vessels Layer Settings, page 14). Radar Setup: Opens the radar display settings (Radar Setup Menu, page 39). Edit Overlays: Adjusts the data shown on the screen

(Customizing the Data Overlays, page 5). Chart Settings NOTE: Not all settings apply to all charts and 3D chart views. Some settings require external accessories or applicable premium charts. From a chart, select Menu > Settings. Orientation: Sets the perspective of the map. Detail: Adjusts the amount of detail shown on the map, at different zoom levels. Chart Size: Sets the visible size of the chart. World Map: Uses either a basic world map or a shaded relief map on the chart. These differences are visible only when zoomed out too far to see the detailed charts. Start Line: Sets the starting line for the sailing race (Setting the Starting Line, page 23). Inset Map: Shows a small map centered on your present location. Fish Eye 3D Settings NOTE: This feature is available with premium charts, in some areas. From the Fish Eye 3D chart view, select Menu. View: Sets the perspective of the 3D chart view. Tracks: Shows tracks. Sonar Cone: Shows a cone that indicates the area covered by the transducer. Fish Symbols: Shows suspended targets. Supported Maps To help you have a safe and enjoyable time on the water, Garmin devices only support official maps produced by Garmin or an approved third party producer. You can purchase maps from Garmin. If you purchase maps from a seller other than Garmin, investigate the seller before purchasing. Be extra cautious with online sellers. If you have purchased an unsupported map, return it to the seller. Garmin Quickdraw Contours Mapping The Garmin Quickdraw Contours mapping feature allows users to generate maps. Garmin makes no representations about the WARNING accuracy, reliability, completeness or timeliness of the maps generated by third parties. Any use or reliance on the maps generated by third parties is at your own risk. The Garmin Quickdraw Contours mapping feature allows you to instantly create maps with contours and depth labels for any body of water. When Garmin Quickdraw Contours records data, a colored circle surrounds the vessel icon. This circle represents the approximate area of the map that is scanned by each pass. A green circle indicates good depth and GPS position, and a speed under 16 km/h (10 mph). A yellow circle indicates good depth and GPS position, and a speed between 16 and 32 km/h

(10 and 20 mph). A red circle indicates poor depth or GPS position, and a speed above 32 km/h (20 mph). You can view Garmin Quickdraw Contours in a combination screen or as a single view on the map. The amount of saved data depends on the size of your memory card, your sonar source, and the speed of your boat as you record data. You can record longer when you use a single-beam sonar. It is estimated that you might be able to record about 1,500 hours of data onto a 2 GB memory card. When you record data on a memory card in your chartplotter, the new data is added to your existing Garmin Quickdraw Contours map, and is saved on the memory card. When you insert a new memory card, the existing data does not transfer onto the new card. Mapping a Body of Water Using the Garmin Quickdraw Contours Feature Before you can use the Garmin Quickdraw Contours feature, you must have sonar depth, your GPS position, and a memory card with free space. 1 From a chart view, select Menu > Quickdraw Contours >

Start Recording. 2 When recording is complete, select Menu > Quickdraw Contours > Stop Recording. 3 Select Manage > Name, and enter a name for the map. Adding a Label to a Garmin Quickdraw Contours Map You can add labels to a Garmin Quickdraw Contours map to mark hazards or points of interest. 1 From the Navigation chart, select a location. 2 Select Quickdraw Lbl.. 3 Enter text for the label, and select Done. Garmin Quickdraw Community The Garmin Quickdraw Community is a free, public, online community that enables you to share your Garmin Quickdraw Contours maps with others. You can also download maps other users have created. If your device has WiFi technology, you can use the ActiveCaptain app to access the Garmin Quickdraw Community

(Connecting to the Garmin Quickdraw Community with ActiveCaptain, page 16). Garmin Quickdraw Contours Mapping 15 If your device does not have WiFi technology, you can use the Garmin Connect website to access the Garmin Quickdraw Community (Connecting to the Garmin Quickdraw Community with Garmin Connect, page 16). Connecting to the Garmin Quickdraw Community with ActiveCaptain 1 From your mobile device, open the ActiveCaptain app and connect to the GPSMAP device (Getting Started with the ActiveCaptain App, page 6). 2 From the app, select Quickdraw Community. You can download contours from others in the community

(Downloading Garmin Quickdraw Community Maps Using ActiveCaptain, page 16) and share the contours you have created (Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using ActiveCaptain, page 16). Downloading Garmin Quickdraw Community Maps Using ActiveCaptain You can download Garmin Quickdraw Contours maps that other users have created and shared with the Garmin Quickdraw Community. 1 From the ActiveCaptain app on your mobile device, select Quickdraw Community > Search for Contours. 2 Use the map and search features to locate an area to download. The red dots represent Garmin Quickdraw Contours maps that have been shared for that area. 3 Select Select Download Region. 4 Drag the box to select the area to download. 5 Drag the corners to change the download area. 6 Select Download Area. The next time you connect the ActiveCaptain app to the GPSMAP device, the downloaded contours are transferred to the device automatically. Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using ActiveCaptain You can share Garmin Quickdraw Contours maps that you have created with others in the Garmin Quickdraw Community. When you share a contour map, only the contour map is shared. Your waypoints are not shared. When you set up your ActiveCaptain app, you may have selected to share your contours with the community automatically. If not, follow these steps to enable sharing. From the ActiveCaptain app on your mobile device, select Sync with Plotter > Contribute to Community. The next time you connect the ActiveCaptain app to the GPSMAP device, your contour maps are transferred to the community automatically. Connecting to the Garmin Quickdraw Community with Garmin Connect 1 Go to connect.garmin.com. 2 Select Getting Started > Quickdraw Community > Getting Started. 3 If you do not have a Garmin Connect account, create one. 4 Sign in to your Garmin Connect account. 5 Select Marine in the upper-right to open the Garmin Quickdraw widget. TIP: Make sure you have a memory card in your computer to share Garmin Quickdraw Contours maps. Sharing Your Garmin Quickdraw Contours Maps with the Garmin Quickdraw Community Using Garmin Connect You can share Garmin Quickdraw Contours maps that you have created with others in the Garmin Quickdraw Community. When you share a contour map, only the contour map is shared. Your waypoints are not shared. 1 Insert a memory card into the card slot (Memory Cards, page 2). 2 Insert the memory card into your computer. 3 Access the Garmin Quickdraw Community (Connecting to the Garmin Quickdraw Community with Garmin Connect, page 16). 4 Select Share Your Contours. 5 Browse to your memory card, and select the /Garmin folder. 6 Open the Quickdraw folder, and select the file named ContoursLog.svy. After the file is uploaded, delete the ContoursLog.svy file from your memory card to avoid issues with future uploads. Your data will not be lost. Downloading Garmin Quickdraw Community Maps Using Garmin Connect You can download Garmin Quickdraw Contours maps that other users have created and shared with the Garmin Quickdraw Community. If your device does not have WiFi technology, you can access the Garmin Quickdraw Community using the Garmin Connect website. If your device has WiFi technology, you should access the Garmin Quickdraw Community using the ActiveCaptain app

(Connecting to the Garmin Quickdraw Community with ActiveCaptain, page 16). 1 Insert the memory card into your computer. 2 Access the Garmin Quickdraw Community (Connecting to the Garmin Quickdraw Community with Garmin Connect, page 16). 3 Select Search for Contours. 4 Use the map and search features to locate an area to download. The red dots represent Garmin Quickdraw Contours maps that have been shared for that region. 5 Select Select an Area to Download. 6 Drag the edges of the box to select the area to download. 7 Select Start Download. 8 Save the file to your memory card. TIP: If you cannot find the file, look in the "Downloads" folder. The browser may have saved the file there. 9 Remove the memory card from your computer. 10Insert the memory card into the card slot (Memory Cards, page 2). The chartplotter automatically recognizes the contours maps. The chartplotter may take a few minutes to load the maps. Garmin Quickdraw Contours Settings From a chart, select Menu > Quickdraw Contours > Settings. Recording Offset: Sets the distance between the sonar depth and the contour recording depth. If the water level has changed since your last recording, adjust this setting so the recording depth is the same for both recordings. For example, if the last time you recorded had a sonar depth of 3.1 m (10.5 ft.), and today's sonar depth is 3.6 m (12 ft.), enter -0.5 m (-1.5 ft.) for the a Recording Offset value. User Display Offset: Sets differences in contour depths and depth labels on your own contours maps to compensate for 16 Garmin Quickdraw Contours Mapping changes in the water level of a body of water, or for depth errors in recorded maps. Comm. Display Offset: Sets differences in contour depths and depth labels on the community contours maps to compensate for changes in the water level of a body of water, or for depth errors in recorded maps. Survey Coloring: Sets the color of the Garmin Quickdraw Contours display. When this setting is turned on, the colors indicate the quality of the recording. When this setting is turned off, the contour areas use standard map colors. Green indicates good depth and GPS position, and a speed under 16 km/h (10 mph). Yellow indicates good depth and GPS position, and a speed between 16 and 32 km/h (10 and 20 mph). Red indicates poor depth or GPS position, and a speed above 32 km/h (20 mph). Depth Shading: Specifies the minimum and maximum depths of a depth range and a color for that depth range. Navigation with a Chartplotter WARNING All route and navigation lines displayed on the chartplotter are only intended to provide general route guidance or to identify proper channels, and are not intended to be precisely followed. Always defer to the navaids and conditions on the water when navigating to avoid groundings or hazards that could result in vessel damage, personal injury, or death. The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects. CAUTION If your vessel has an autopilot system, a dedicated autopilot control display must be installed at each steering helm in order to disable the autopilot system. NOTE: Some chart views are available with premium charts, in some areas. To navigate, you must choose a destination, set a course or create a route, and follow the course or route. You can follow the course or the route on the Navigation chart, Fishing chart, Perspective 3D chart view, or Mariners Eye 3D chart view. You can set and follow a course to a destination using one of three methods: Go To, Route To, or Auto Guidance. Go To: Takes you directly to the destination. This is the standard option for navigating to a destination. The chartplotter creates a straight-line course or navigation line to the destination. The path may run over land and other obstacles. Route To: Creates a route from your location to a destination, allowing you to add turns along the way. This option provides a straight-line course to the destination, but allows you to add turns into the route to avoid land and other obstacles. Auto Guidance: Uses the specified information about your vessel and chart data to determine the best path to your destination. This option is available only when using a compatible premium chart in a compatible chartplotter. It provides a turn-by-turn navigation path to the destination, avoiding land and other obstacles (Auto Guidance, page 20). When you are using a compatible autopilot connected to the chartplotter using NMEA 2000, the autopilot follows the Auto Guidance route. NOTE: Auto Guidance is available with premium charts, in some areas. Basic Navigation Questions Question Answer How do I make the chartplotter point me in the direction in which I want to go

(bearing)?

How do I make the device guide me along a straight line

(minimizing cross track) to a location using the shortest distance from the present location?

How do I make the device guide me to a location while avoiding charted obstacles?

How do I make the device steer my automatic pilot?

Can the device create a path for me?

Navigate using Go To (Setting and Following a Direct Course Using Go To, page 18). Build a single-leg route and navigate it using Route To (Creating and Navigating a Route From Your Present Location, page 19). Build a multi-leg route and navigate it using Route To (Creating and Navigating a Route From Your Present Location, page 19). Navigate using Route To (Creating and Navigating a Route From Your Present Location, page 19). If you have premium maps that support Auto Guidance and are in an area covered by Auto Guidance, navigate using Auto Guidance (Setting and Following an Auto Guidance Path, page 20). How do I change the Auto Guidance settings for my boat?

See Auto Guidance Path Configurations, page 20. Destinations You can select destinations using various charts and 3D chart views or using the lists. Searching for a Destination by Name You can search for saved waypoints, saved routes, saved tracks, and marine services destinations by name. 1 Select Info > Services > Search by Name. 2 Enter at least a portion of the name of your destination. 3 If necessary, select Done. The 50 nearest destinations that contain your search criteria appear. 4 Select the destination. Selecting a Destination Using the Navigation Chart From the Navigation chart, select a destination. Searching for a Marine Services Destination NOTE: This feature is available with premium charts, in some areas. The chartplotter contains information for thousands of destinations offering marine services. 1 Select Info > Services. 2 Select Offshore Services or Inland Services. 3 If necessary, select the marine service category. The chartplotter shows a list of the nearest locations and the distance and bearing to each. 4 Select a destination. You can select Next Page or Previous Page to view additional information or to show the location on a chart. Navigation with a Chartplotter 17 Setting and Following a Direct Course Using Go To WARNING When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects. You can set and follow a direct course from your current location to a selected destination. 1 Select a destination (Destinations, page 17). 2 Select Navigate To > Go To. A magenta line appears. In the center of the magenta line is a thinner purple line that represents the corrected course from your current location to the destination. The corrected course is dynamic, and it moves with your boat when you are off course. 3 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. 4 If you are off course, follow the purple line (corrected course) to go to your destination, or steer back to the magenta line

(direct course). You can also use the orange course-to-steer arrow, which shows a proposed turning radius to return your boat to the course. WARNING Review the path for obstacles before negotiating the turn. If the path is unsafe, reduce your boat speed and determine a safe path back to the course. Projecting a Waypoint You can create a new waypoint by projecting the distance and bearing from a different location. This can be helpful when creating sail racing start and finish lines. 1 Select Waypoints > New Waypoint > Enter Range/

Bearing. 2 if necessary, select a reference point on the chart. 3 Select Enter Range/Bearing. 4 Enter the distance, and select Done. 5 Enter the bearing, and select Done. 6 Select Create Waypoint. Viewing a List of all Waypoints Select Info > User Data > Waypoints. Editing a Saved Waypoint 1 Select Info > User Data > Waypoints. 2 Select a waypoint. 3 Select Review > Edit. 4 Select an option:

To add a name, select Name, and enter a name. To change the symbol, select Symbol. To change the depth, select Depth. To change the water temperature, select Water Temp.. To change the comment, select Comment. To move the position of the waypoint, select Position. Stopping Navigation While navigating, from an applicable chart, select an option:

Select Menu > Stop Navigation. When navigating with Auto Guidance, select Menu >

Navigation Options > Stop Navigation. Moving a Saved Waypoint 1 Select Waypoints. 2 Select a waypoint. 3 Select Review > Move. 4 Indicate a new location for the waypoint:

Select

. Waypoints Waypoints are locations you record and store in the device. Waypoints can mark where you are, where you are going, or where you have been. You can add details about the location, such as name, elevation, and depth. Marking Your Present Location as a Waypoint From any screen, select Mark. Creating a Waypoint at a Different Location 1 Select Waypoints > New Waypoint. 2 Select an option:

To create the waypoint by entering position coordinates, select Enter Coordinates, and enter the coordinates. To create the waypoint using a chart, select Use Chart, select the location, and select Select. To create the waypoint using a range (distance) and bearing, select Enter Range/Bearing, and enter the information. Marking an SOS Location You can mark an SOS or MOB (man overboard) location. 1 Hold SOS for one second. 2 Select the SOS type. 3 If necessary, select OK to navigate to the man overboard location. If you selected OK, the chartplotter sets a direct course back to the location. If you selected another type of SOS, the call details are sent to the VHF radio. You must send the call using the radio. To move the waypoint while using the chart, select Use Chart, select a new location on the chart, and select Move. To move the waypoint using coordinates, select Enter Coordinates, and enter the new coordinates. To move the waypoint using a range (distance) and bearing, select Enter Range/Bearing, and enter the information. Browsing for and Navigating to a Saved Waypoint WARNING All route and navigation lines displayed on the chartplotter are only intended to provide general route guidance or to identify proper channels, and are not intended to be precisely followed. Always defer to the navaids and conditions on the water when navigating to avoid groundings or hazards that could result in vessel damage, personal injury, or death. The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. When using Go To, a direct course and a corrected course may pass over land or shallow water. Use visual sightings, and steer to avoid land, shallow water, and other dangerous objects. NOTE: Auto Guidance is available with premium charts, in some areas. Before you can navigate to a waypoint, you must create a waypoint. 1 Select Info > User Data > Waypoints. 2 Select a waypoint. 18 Navigation with a Chartplotter 3 Select Navigate To. 4 Select an option:

To navigate directly to the location, select Go To. To create a route to the location, including turns, select Route To. To use Auto Guidance, select Auto Guidance. 5 Review the course indicated by the magenta line. NOTE: When using Auto Guidance, a gray segment within any part of the magenta line indicates that Auto Guidance cannot calculate part of the Auto Guidance line. This is due to the settings for minimum safe water depth and minimum safe obstacle height. 6 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. Deleting a Waypoint or an MOB 1 Select Info > User Data > Waypoints. 2 Select a waypoint or an MOB. 3 Select Review > Delete. Deleting All Waypoints Select Info > User Data > Delete User Data > Waypoints >

All. Routes A route is a path from one location to one or more destinations. Creating and Navigating a Route From Your Present Location You can create and immediately navigate a route on the Navigation chart or the Fishing chart. This method does not save the route. 1 From the Navigation chart or Fishing chart, select a destination. 2 Select Navigate To > Route To. 3 Select the location of the last turn before the destination. 4 Select Add Turn. 5 If necessary, repeat to add turns, working backward from the destination to the present location of your vessel. The last turn you add should be the first turn you make, starting from your present location. It should be the turn closest to your vessel. 6 If necessary, select Menu. 7 Select Done. 8 Review the course indicated by the magenta line. 9 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. Creating and Saving a Route You can add up to 250 turns to one route. 1 Select Info > User Data > Routes & Auto Guidance Paths

> New > Route Using Chart. 2 Select the starting location of the route. The starting point can be your present location or another location. 3 Select Add Turn. 4 Select the location of the next turn on the chart. 5 Select Add Turn. 6 If necessary, repeat steps 4 and 5 to add more turns. 7 Select the final destination. Viewing a List of Routes and Auto Guidance Paths 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 If necessary, select Filter to see routes only or Auto Guidance paths only. Editing a Saved Route You can change the name of a route or change the turns the route contains. 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a route. 3 Select Review > Edit Route. 4 Select an option:

To change the name, select Name, and enter the name. To edit a turn from a list, select Edit Turns > Use Turn List, and select a turn from the list. To select a turn using the chart, select Edit Turns > Use Chart, and select a location on the chart. Modifying a turn that uses a saved waypoint does not move that waypoint, it relocates the turn in the route. Moving the location of a waypoint used in a route does not move the turn in the route. Browsing for and Navigating a Saved Route Before you can browse a list of routes and navigate to one of them, you must create and save at least one route. 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a route. 3 Select Navigate To. 4 Select an option:

To navigate the route from the starting point used when the route was created, select Forward. To navigate the route from the destination point used when the route was created, select Backward. A magenta line appears. In the center of the magenta line is a thinner purple line that represents the corrected course from your present location to the destination. The corrected course is dynamic, and it moves with your boat when you are off course. 5 Review the course indicated by the magenta line. 6 Follow the magenta line along each leg in the route, steering to avoid land, shallow water, and other obstacles. 7 If you are off course, follow the purple line (corrected course) to go to your destination, or steer back to the magenta line

(direct course). Browsing for and Navigating Parallel to a Saved Route Before you can browse a list of routes and navigate to one of them, you must create and save at least one route. 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a route. 3 Select Navigate To. 4 Select Offset to navigate parallel to the route, offset from it by a specific distance. 5 Indicate how to navigate the route:

To navigate the route from the starting point used when the route was created, to the left of the original route, select Forward - Port. To navigate the route from the starting point used when the route was created, to the right of the original route, select Forward - Starboard. To navigate the route from the destination point used when the route was created, to the left of the original route, select Backward - Port. Navigation with a Chartplotter 19 To navigate the route from the destination point used when the route was created, to the right of the original route, select Backward - Starboard. 6 If necessary, select Done. A magenta line appears. In the center of the magenta line is a thinner purple line that represents the corrected course from your present location to the destination. The corrected course is dynamic, and it moves with your boat when you are off course. 7 Review the course indicated by the magenta line. 8 Follow the magenta line along each leg in the route, steering to avoid land, shallow water, and other obstacles. 9 If you are off course, follow the purple line (corrected course) to go to your destination, or steer back to the magenta line

(direct course). Initiating a Search Pattern You can initiate a search pattern to search an area. Different patterns are better suited for different search situations. 1 Select Info > User Data > Routes & Auto Guidance Paths

> New > Route Using SAR Pattern. 2 Select a pattern:

Select Sector Search when the location of the object is fairly known, the search area is small, and an intensive search is needed. Select Expanding Square when the location of the object is somewhat doubtful, the search area is small, and an intensive search is needed. Select Creeping/Parallel Line when the location of the object is approximate, the search area is small, and a consistent search is needed. 3 Enter the search parameters. 4 Select Done. 5 If necessary, select Engage. Deleting a Saved Route 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a route. 3 Select Review > Delete. Deleting All Saved Routes Select Info > User Data > Delete User Data > Routes &

Auto Guidance Paths. Auto Guidance WARNING The Auto Guidance feature is based on electronic chart information. That data does not ensure obstacle and bottom clearance. Carefully compare the course to all visual sightings, and avoid any land, shallow water, or other obstacles that may be in your path. All route and navigation lines displayed on the chartplotter are only intended to provide general route guidance or to identify proper channels, and are not intended to be precisely followed. Always defer to the navaids and conditions on the water when navigating to avoid groundings or hazards that could result in vessel damage, personal injury, or death. NOTE: Auto Guidance is available with premium charts, in some areas. You can use Auto Guidance to plot the best path to your destination. Auto Guidance uses your chartplotter to scan chart data, such as water depth and known obstacles, to calculate a suggested path. You can adjust the path during navigation. Setting and Following an Auto Guidance Path 1 Select a destination (Destinations, page 17). 2 Select Navigate To > Auto Guidance. 3 Review the path, indicated by the magenta line. 4 Select Start Navigation. 5 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. NOTE: When using Auto Guidance, a gray segment within any part of the magenta line indicates that Auto Guidance cannot calculate part of the Auto Guidance line. This is due to the settings for minimum safe water depth and minimum safe obstacle height. Creating and Saving an Auto Guidance Path 1 Select Info > User Data > Routes & Auto Guidance Paths

> New > Auto Guidance. 2 Select a starting point, and select Next. 3 Select a destination, and select Next. 4 Select an option:

To view a hazard and adjust the path near a hazard, select Hazard Review. To adjust the path, select Adjust Path, and follow the on-

screen instructions. To delete the path, select Cancel Auto Guidance. To save the path, select Done. Adjusting a Saved Auto Guidance Path 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a path, and select Review > Edit > Adjust Path. TIP: When navigating an Auto Guidance path, select the path on the navigation chart, and select Adjust Path. 3 Select a location on the path. 4 Drag the point to a new location. 5 If necessary, select a point, and select Remove. 6 Select Done. Canceling an Auto Guidance Calculation in Progress From the Navigation chart, select Menu > Cancel. TIP: You can select Back to quickly cancel the calculation. Setting a Timed Arrival You can use this feature on a route or an Auto Guidance path to get feedback about when you should arrive at a selected point. This allows you to time your arrival at a location, such as a bridge opening or a race starting line. 1 From the Navigation chart, select Menu. 2 Select Navigation Options > Timed Arrival. TIP: You can quickly open the Timed Arrival menu by selecting a point on the path or route. Auto Guidance Path Configurations CAUTION The Preferred Depth and Vertical Clearance settings influence how the chartplotter calculates an Auto Guidance path. If an area has an unknown water depth or an unknown obstacle height, the Auto Guidance path is not calculated in that area. If an area at the beginning or the end of an Auto Guidance path is shallower than the Preferred Depth or lower than the Vertical Clearance settings, the Auto Guidance path may not be calculated in that area, depending on the map data. On the chart, the course through those areas appears as a gray line or a magenta and gray striped line. When your boat enters one of those areas, a warning message appears. 20 Navigation with a Chartplotter NOTE: Auto Guidance is available with premium charts, in some areas. NOTE: Not all settings apply to all maps. You can set the parameters the chartplotter uses when calculating an Auto Guidance path. Preferred Depth: Sets the minimum water depth, based on chart depth data, that your boat can safely travel over. NOTE: The minimum water depth for the premium charts

(made before 2016) is 3 feet. If you enter a value of less than 3 feet, the charts only use depths of 3 feet for Auto Guidance path calculations. Vertical Clearance: Sets the minimum height of a bridge or obstacle, based on chart data, that your boat can safely travel under. Shoreline Distance: Sets how close to the shore you want the Auto Guidance path to be placed. The Auto Guidance path may move if you change this setting while navigating. The available values for this setting are relative, not absolute. To ensure that the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Auto Guidance path using one or more familiar destinations that require navigation through a narrow waterway (Adjusting the Distance from Shore, page 21). Adjusting the Distance from Shore The Shoreline Distance setting indicates how close to the shore you want the Auto Guidance line to be placed. The Auto Guidance line may move if you change this setting while navigating. The available values for the Shoreline Distance setting are relative, not absolute. To ensure the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Auto Guidance line using one or more familiar destinations that require navigation through a narrow waterway. 1 Dock your vessel or drop the anchor. 2 Select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Normal. 3 Select a destination that you have navigated to previously. 4 Select Navigate To > Auto Guidance. 5 Review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. 6 Select an option:

If the placement of the Auto Guidance line is satisfactory, select Menu > Navigation Options > Stop Navigation, and proceed to step 10. If the Auto Guidance line is too close to known obstacles, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Far. If the turns in the Auto Guidance line are too wide, select Settings > Preferences > Navigation > Auto Guidance

> Shoreline Distance > Near. 7 If you selected Near or Far in step 6, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway. 8 Select an option:

If the placement of the Auto Guidance line is satisfactory, select Menu > Navigation Options > Stop Navigation, and proceed to step 10. If the Auto Guidance line is too close to known obstacles, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Farthest. If the turns in the Auto Guidance line are too wide, select Settings > Preferences > Navigation > Auto Guidance

> Shoreline Distance > Nearest. 9 If you selected Nearest or Farthest in step 8, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway. 10Repeat steps 3 through 9 at least once more, using a different destination each time, until you are familiar with the functionality of the Shoreline Distance setting. Tracks A track is a recording of the path of your boat. The track currently being recorded is called the active track, and it can be saved. You can show tracks in each chart or 3D chart view. Showing Tracks 1 From a chart, select Menu > Layers > User Data > Tracks. 2 Select the tracks to display. A trailing line on the chart indicates your track. Setting the Color of the Active Track 1 Select Info > User Data > Tracks > Active Track Options >

Track Color. 2 Select a track color. Saving the Active Track The track currently being recorded is called the active track. 1 Select Info > User Data > Tracks > Save Active Track. 2 Select an option:

Select the time the active track began. Select Entire Log. 3 Select Save. Viewing a List of Saved Tracks Select Info > User Data > Tracks > Saved Tracks. Editing a Saved Track 1 Select Info > User Data > Tracks > Saved Tracks. 2 Select a track. 3 Select Review > Edit Track. 4 Select an option:

Select Name, and enter the new name. Select Track Color, and select a color. Saving a Track as a Route 1 Select Info > User Data > Tracks > Saved Tracks. 2 Select a track. 3 Select Select > Edit Track > Save as Route. Browsing for and Navigating a Recorded Track Before you can browse a list of tracks and navigate to them, you must record and save at least one track (Tracks, page 21). 1 Select Info > User Data > Tracks > Saved Tracks. 2 Select a track. 3 Select Follow Track. Navigation with a Chartplotter 21 4 Select an option:

To navigate the track from the starting point used when the track was created, select Forward. To navigate the track from the destination point used when the track was created, select Backward. 5 Review the course indicated by the colored line. 6 Follow the line along each leg in the route, steering to avoid land, shallow water, and other obstacles. Deleting a Saved Track 1 Select Info > User Data > Tracks > Saved Tracks. 2 Select a track. 3 Select Review > Delete. Deleting All Saved Tracks Select Info > User Data > Delete User Data > Saved Tracks. Retracing the Active Track The track currently being recorded is called the active track. 1 Select Info > User Data > Tracks > Follow Active Track. 2 Select an option:

Select the time the active track began. Select Entire Log. 3 Review the course indicated by the colored line. 4 Follow the colored line, steering to avoid land, shallow water, and other obstacles. Clearing the Active Track Select Info > User Data > Tracks > Clear Active Track. The track memory is cleared, and the active track continues to be recorded. Managing the Track Log Memory During Recording 1 Select Info > User Data > Tracks > Active Track Options. 2 Select Record Mode. 3 Select an option:

Fill. To continuously record a track log, replacing the oldest track data with new data, select Wrap. Configuring the Recording Interval of the Track Log You can indicate the frequency at which the track plot is recorded. Recording more frequent plots is more accurate but fills the track log faster. The resolution interval is recommended for the most efficient use of memory. 1 Select Info > User Data > Tracks > Active Track Options >

Interval. 2 Select an option:

To record the track based on a distance between points, select Interval > Distance > Change, and enter the distance. To record the track based on a time interval, select Interval > Time > Change, and enter the time interval. To record the track plot based on a variance from your course, select Interval > Resolution > Change, and enter the maximum error allowed from the true course before recording a track point. This is the recommended recording option. Boundaries Boundaries allow you to avoid or remain in designated areas in a body of water. You can set an alarm to alert you when you enter or exit a boundary. You can create boundary areas, lines, and circles using the map. You can also convert saved tracks and routes into boundary lines. You can create a boundary area using waypoints by creating a route from the waypoints, and converting the route into a boundary line. You can select a boundary to act as the active boundary. You can add the active boundary data to the data fields on the chart. Creating a Boundary 1 Select Info > User Data > Boundaries > New. 2 Select a boundary shape. 3 Follow the on-screen instructions. Converting a Route to a Boundary Before you can convert a route to a boundary, you must create and save at least one route (Creating and Saving a Route, page 19). 1 Select Info > User Data > Routes & Auto Guidance Paths. 2 Select a route. 3 Select Review > Edit Route > Save as Boundary. Converting a Track to a Boundary Before you can convert a track to a boundary, you must record and save at least one track (Saving the Active Track, page 21). 1 Select Info > User Data > Tracks > Saved Tracks. 2 Select a track. 3 Select Review > Edit Track > Save as Boundary. Editing a Boundary 1 Select Info > User Data > Boundaries. 2 Select a boundary. 3 Select Review. 4 Select an option:

To edit the appearance of the boundary on the chart, select Display Options. To change the boundary lines or name, select Edit Boundary. Linking a Boundary to a SmartMode Layout You can link a boundary to a SmartMode layout to automatically open the layout when entering or exiting the boundary. For example, you can set a boundary around your marina, and automatically open the Docking layout when you approach the marina. 1 Select Info > User Data > Boundaries. 2 Select a boundary. 3 Select Review > Link SmartMode > SmartMode. 4 Select Entering, and select a layout. 5 Select Exiting, and select a layout. Setting a Boundary Alarm Boundary alarms alert you when you are within a specified distance of a set boundary. This can be helpful when attempting to avoid certain areas or when you should be very alert in certain areas, such as shipping lanes. 1 Select Info > User Data > Boundaries. 2 Select a boundary. 3 Select Review > Alarm. 4 Select an option:

To set an alarm for when your boat is a specified distance from the boundary, select Warning Dist., enter a distance, and select Done. To set an alarm when you enter or exit the boundary, select Area to show Entering or Exiting. To record a track log until the track memory is full, select To edit the boundary alarm, select Alarm. 22 Navigation with a Chartplotter Disabling all Boundary Alarms Select Info > User Data > Boundaries > Alarms. To switch the position of the port and starboard marks after you have set them, select Swap Port & Starbd.. Deleting a Boundary 1 Select Info > User Data > Boundaries. 2 Select a boundary. 3 Select Review > Edit Boundary > Delete. Deleting All Saved Waypoints, Tracks, Routes, and Boundaries Select Info > User Data > Delete User Data > Delete All User Data > OK. Sailing Features Setting the Vessel Type You can select your boat type to configure the chartplotter settings and to use features customized for your boat type. 1 Select Settings > My Vessel > Vessel Type. 2 Select an option. Sail Racing You can use the device to increase the likelihood that your boat will cross the start line of a race exactly when the race begins. When you synchronize the race timer with the official race countdown timer, you are alerted at one-minute intervals as the race start approaches. When you combine the race timer with the virtual start line, the device measures your speed, bearing, and remaining time on the countdown timer. The device uses this data to indicate whether your boat will cross the start line before, after, or at the correct time to start the race. Starting Line Guidance Sailing start line guidance is a visual representation of the information you need to cross the start line at the optimal time and speed. After you set the starboard and port start line pins, and the target speed and time, and after you start the race timer, a predictor line appears. The predictor line extends from your current location toward the start line and the laylines that extend from each pin. The end point and color of the predictor line indicate where the boat will be when the timer expires, based on your current boat speed. When the end point is before the start line, the line is white. This indicates the boat must increase speed to reach the start line on time. When the end point is past the start line, the line is red. This indicates the boat must reduce speed to avoid a penalty for reaching the start line before the timer expires. When the end point is on the start line, the line is white. This indicates the boat is moving at an optimal speed to reach the start line when the timer expires. By default, the start line guidance window and the race timer window appear in the Sail Racing combination screen. Setting the Starting Line The start line guidance window is added to the Sail Racing combination screen by default. 1 From the Sail Racing combination screen, select Menu >

Start Line Guidance > Start Line. 2 Select an option:

To mark the port and starboard starting line marks as you sail past them, select Ping Marks. To mark the port and starboard starting line marks by entering their coordinates, select Enter Coordinates. Using the Starting Line Guidance You can use the starting line guidance feature to help get you cross the start line, at the optimal speed during a sailing race. 1 Mark the starting line (Setting the Starting Line, page 23). 2 From the Sail Racing combination screen, select Menu >

Start Line Guidance > Target Speed, and select your target speed when crossing the starting line. 3 Select Target Time, and select the target time to cross the starting line. 4 Select Back. 5 Start the racing timer (Starting the Race Timer, page 23). Starting the Race Timer The race timer is added to the Sail Racing combination screen by default. 1 From the Sail Racing combination screen, select Start. NOTE: You can also access this from the Sailing SmartMode screen and the navigation chart. 2 When necessary, select Sync to synchronize with the official race timer. Stopping the Race Timer From the Sail Racing combination screen, select Stop. Setting the Distance between the Bow and the GPS Antenna You can enter the distance between the bow of your boat and the location of your GPS antenna. This helps ensure the bow of your boat crosses the starting line at the precise start time. 1 From a navigation chart, select Menu > Sailing > Start Line

> GPS Bow Offset. 2 Enter the distance. 3 Select Done. Laylines Settings To use the laylines features, you must connect a wind sensor to the chartplotter. When in sailing mode (Setting the Vessel Type, page 5), you can display laylines on the navigation chart. Laylines can be very helpful when racing. From the navigation chart, select Menu > Layers > My Vessel >

Laylines > Setup. Display: Sets how the laylines and vessel appear on the chart, and sets the length of the laylines. Sailing Ang.: Allows you to select how the device calculates laylines. The Actual option calculates the laylines using the measured wind angle from the wind sensor. The Manual option calculates the laylines using manually entered windward and leeward angles. Windward Ang.: Allows you to set a layline based on the windward sailing angle. Sailing Features 23 Leeward Ang.: Allows you to set a layline based on the leeward Sailboat Autopilot Operation sailing angle. Tide Correction: Corrects the laylines based on the tide. Layline Filter: Filters the layline data based on the time interval entered. For a smoother layline that filters out some of the changes in the boat's heading or true wind angle, enter a higher number. For laylines that display a higher sensitivity to changes in the boat's heading or true wind angle, enter a lower number. Setting the Keel Offset You can enter a keel offset to compensate the water depth reading for the transducer installation location. This allows you to view the depth of the water below the keel or the true depth of the water, depending on your needs. If you want to know the water depth below the keel or the lowest point of your boat and the transducer is installed at the water line or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat. If you want to know the true water depth and the transducer is installed below the water line, measure the distance from the bottom of the transducer up to the water line. NOTE: This option is only available when you have valid depth data. 1 Measure the distance:

If the transducer is installed at the water line or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat. Enter this value as a positive number. If the transducer is installed at the bottom of the keel and you want to know the true depth of the water, measure the distance from the transducer to the water line. Enter this value in as a negative number. 2 Complete an action:

If the transducer is connected to the chartplotter or a sonar module, select Settings > My Vessel > Depth and Anchoring > Keel Offset. If the transducer is connected to the NMEA 2000 network, select Settings > Communications > NMEA 2000 Setup

> Device List, select the transducer, and select Review >

Keel Offset. if the transducer is installed at the water line, or if the transducer is installed at the bottom of the 4 Enter the distance measured in step 1. 3 Select select keel. 24 CAUTION When engaged, the autopilot controls only the rudder. You and your crew remain responsible for the sails while the autopilot is engaged. In addition to heading hold, you can use the autopilot to maintain a wind hold. You can also use the autopilot to control the rudder while tacking and gybing. Wind Hold You can set the autopilot to maintain a specific bearing relative to the current wind angle. Your device must be connected to a NMEA 2000 or NMEA 0183 compatible wind sensor to perform a wind hold or a wind-based tack or gybe. Setting the Wind Hold Type Before you can enable the wind hold type, you must connect a NMEA 2000 or NMEA 0183 wind sensor to the autopilot. For advanced autopilot configuration, see the installation instructions included with your autopilot. 1 From the autopilot screen, select Menu > Autopilot Setup >

Wind Hold Type. 2 Select Apparent or True. Engaging Wind Hold Before you can enable the wind hold type, you must connect a NMEA 2000 or NMEA 0183 wind sensor to the autopilot. When the autopilot is in standby mode, select Wind Hold. Engaging Wind Hold from Heading Hold Before you can enable the wind hold type, you must connect a NMEA 2000 or NMEA 0183 wind sensor to the autopilot. With heading hold engaged, select Menu > Wind Hold. Adjusting the Wind Hold Angle with the Autopilot You can adjust the wind hold angle on the autopilot when wind hold is engaged. To adjust the wind hold angle in increments of 1, select or To adjust the wind hold angle in increments of 10, hold or

. Tack and Gybe You can set the autopilot to perform a tack or gybe while heading hold or wind hold is engaged. Tacking and Gybing from Heading Hold 1 Engage heading hold (Engaging the Autopilot, page 40). 2 Select Menu. 3 Select an option. The autopilot steers your boat through a tack or gybe. Tacking and Gybing from Wind Hold Before you can engage wind hold, you must have a wind sensor installed. 1 Engage wind hold (Engaging Wind Hold, page 24). 2 Select Menu. 3 Select an option. The autopilot steers your boat through a tack or gybe, and information about the progress of the tack or gybe appears on the screen. Setting a Tack and Gybe Delay The tack and gybe delay allows you to delay steering a tack and gybe after you initiate the maneuver. 1 From the autopilot screen, select Menu > Autopilot Setup >

Sailing Setup > Tack Delay. 2 Select the length of the delay. Sailing Features If you do not see an arrangement of sonar views to suit your needs, you can create a custom combination screen (Creating a New Combination Page, page 5) or a SmartMode layout (Adding a SmartMode Layout, page 4). Stopping the Transmission of Sonar Signals To disable the active sonar, from the sonar screen, select Menu > Transmit. To disable all sonar transmissions, press

, and select Disable All Sonar Trans.. Changing the Sonar View 1 From a combination screen or SmartMode layout with sonar, select the window to change. 2 Select Menu > Change Sonar. 3 Select a sonar view. Traditional Sonar View There are several full-screen views available, depending on the transducer that is connected. The full-screen Traditional sonar view shows a large image of the sonar readings from a transducer. The range scale along the right side of the screen shows the depth of detected objects as the screen scrolls from the right to the left. Depth information Suspended targets or fish Bottom of the body of water Split-Frequency Sonar View In the split-frequency sonar view, the two sides of the screen show a full-view graph of sonar data of different frequencies. NOTE: The split-frequency sonar view requires the use of a dual-frequency transducer. Split-Zoom Sonar View The split-zoom sonar view shows a full-view graph of sonar readings, and a magnified portion of that graph, on the same screen. Garmin ClearV Sonar View NOTE: To receive Garmin ClearV scanning sonar, you need a compatible chartplotter or fishfinder and a compatible transducer. For information about compatible transducers, go to garmin.com/transducers. Garmin ClearV high-frequency sonar provides a detailed picture of the fishing environment around the boat in a detailed representation of structures the boat is passing over. 3 If necessary, select Done. Enabling the Gybe Inhibitor NOTE: The gybe inhibitor does not prevent you from manually performing a gybe using the helm or step steering. The gybe inhibitor prevents the autopilot from performing a gybe. 1 From the autopilot screen, select Menu > Autopilot Setup >

Sailing Setup > Gybe Inhibitor. 2 Select Enabled. Heading Line and Angle Markers The heading line is an extension drawn on the map from the bow of the boat in the direction of travel. Angle markers indicate relative position from the heading or course over ground, which are helpful for casting or finding reference points. Setting the Heading Line and Angle Markers The heading line is an extension drawn on the map from the bow of the boat in the direction of travel. Angle markers indicate relative position from the heading or course over ground, which are helpful for casting or finding reference points. You can show the heading line and the course over ground

(COG) line on the chart. COG is your direction of movement. Heading is the direction the bow of the boat is pointed, when a heading sensor is connected. 1 From a chart, select Menu > Layers > My Vessel > Heading Line > Angle Markers. 2 If necessary, select Source, and select an option:

To automatically use the available source, select Auto. To use the GPS antenna heading for COG, select GPS To use data from a connected heading sensor, select Heading (COG). North Reference. To use data from both a connected heading sensor and the GPS antenna, select COG and Heading. This displays both the heading line and the COG line on the chart. 3 Select Display, and select an option:

Select Distance > Distance, and enter the length of the line shown on the chart. Select Time > Time, and enter the time used to calculate the distance your boat will travel in the specified time at your present speed. Sonar Fishfinder When properly connected to a transducer, your compatible chartplotter can be used as a fishfinder. Chartplotter models without an xsv or xs in their names require a Garmin sounder module and transducer to display sonar information. For more information about which transducer is best for your needs, go to garmin.com/transducers. Different sonar views can help you view the fish in the area. The sonar views available vary depending on the type of transducer and sounder module connected to the chartplotter. For example, you can view certain Panoptix sonar screens only if you have a compatible Panoptix transducer connected. There are four basic styles of sonar views available: a full-

screen view, a split-screen view that combines two or more views, a split-zoom view, and a split-frequency view that displays two different frequencies. You can customize the settings for each view in the screen. For example, if you are viewing the split-frequency view, you can separately adjust the gain for each frequency. Sonar Fishfinder 25 Traditional transducers emit a conical beam. The Garmin ClearV scanning sonar technology emits two narrow beams, similar to the shape of the beam in a copying machine. These beams provide a clearer, picture-like image of what is beneath the boat. Measuring Distance on the Sonar Screen You can measure the distance between two points on the SideV sonar view. 1 From the SideV sonar view, select 2 Select a location on the screen. 3 Select Measure. A push pin appears on the screen at the selected location. 4 Select another location. The distance and angle from the pin is listed in the upper-left corner. TIP: To reset the pin and measure from the current location of the pin, select Set Reference. Panoptix Sonar Views To receive Panoptix sonar, you need a compatible transducer. The Panoptix sonar views allow you to see all around the boat in real time. You can also watch your bait underwater and bait schools in front of or below your boat. The LiveV sonar views provide you a view of the live movement either in front of or below your boat. The screen updates very quickly, producing sonar views that look more like live video. The RealV 3D sonar views provide three-dimensional views of either what is in front of or below your boat. The screen updates with each sweep of the transducer. To see all five Panoptix sonar views, you need one transducer to show the down views and a second transducer to show the forward views. To access the Panoptix sonar views, select Sonar, and select a view. LiveV Down Sonar View This sonar view shows a two-dimensional view of what is below the boat and can be used to see a bait ball and fish. SideV Sonar View NOTE: Not all models provide built-in SideV sonar support. If your model does not provide built-in SideV sonar, you need a compatible sounder module and compatible SideV transducer. If your model does provide built-in SideV sonar, you need a compatible SideV transducer. SideV scanning sonar technology shows you a picture of what lies to the sides of the boat. You can use this as a search tool to find structures and fish. Left side of the boat Right side of the boat The transducer on your vessel Trees Old tires Logs Distance from the side of the boat Water between the vessel and the bottom SideV Scanning Technology Instead of a more common conical beam, the SideV transducer uses a flat beam to scan the water and bottom to the sides of your boat. Panoptix down view history in a scrolling sonar view Boat Range Trails 26 Sonar Fishfinder Color legend Boat Sonar beam Range Fish Bottom Color legend Boat Range Bottom Structure Fish Drop shot rig Bottom LiveV Forward Sonar View This sonar view shows a two-dimensional view of what is in front of the boat and can be used to see a bait ball and fish. RealV 3D Historical Sonar View This sonar view provides a three-dimensional view of what is behind your boat as you are moving and shows the entire water column in 3D, from the bottom to the top of the water. This view is used for finding fish. RealV 3D Forward Sonar View This sonar view shows a three-dimensional view of what is in front of the transducer. This view can be used when you are stationary and you need to see the bottom and the fish approaching the boat. Boat Range Fish Trails Bottom Color legend Boat Ping indicator Fish Bottom Range FrontV Sonar View The Panoptix FrontV sonar view increases your situational awareness by showing obstructions under the water, up to 91 meters (300 feet) in front of the boat. The ability to effectively avoid forward collisions with FrontV sonar decreases as your speed rises above 8 knots. To see the FrontV sonar view, you must install and connect a compatible transducer, such as a PS21 transducer. You may need to update the transducer software. RealV 3D Down Sonar View This sonar view shows a three-dimensional view of what is below the transducer and can be used when you are stationary and want to see what is around your boat. Panoptix LiveScope Sonar View This sonar view shows a live view of what is in front of or below the boat and can be used to see fish and structures. Sonar Fishfinder 27 Depth information Suspended targets or fish Bottom of the body of water Perspective View This sonar view shows a live view of what is around and ahead of your boat and can be used to see shorelines, fish, and structures. This view is best used in shallow water of 50 feet

(15 meters) or less. To see this sonar view, you must install a Panoptix LiveScope transducer on a Perspective Mode Mount (010-12970-00). Selecting the Transducer Type This chartplotter is compatible with a range of accessory transducers, including the Garmin ClearV transducers, which are available at garmin.com/transducers. If you are connecting a transducer that was not included with the chartplotter, you may need to set the transducer type to make the sonar function properly. NOTE: Not all chartplotters and sonar modules support this feature. 1 Complete an action:

From a sonar view, select Menu > Sonar Setup >

Installation > Transducers. Select Settings > My Vessel > Transducers. 2 Select an option:

To enable the chartplotter to detect the transducer automatically, select the transducer to change, and select Auto Detect. To select the transducer manually, select the transducer to change, select the transducer model from the list, and select Change Model. NOTE: If you select the transducer manually, disconnect that transducer, and then connect a different transducer, you should reset this option to Auto Detect. Selecting a Sonar Source This feature may not be available with all models. When you are using more than one sonar data source for a particular sonar view, you can select the source to use for that sonar view. For example, if you have two sources for Garmin ClearV, you can select the source to use from the Garmin ClearV sonar view. 1 Open the sonar view for which you will change the source. 2 Select Menu > Sonar Setup > Source. 3 Select the source for this sonar view. Renaming a Sonar Source You can rename a sonar source to easily identify that source. For example, you use "Bow" as the name of the transducer on the bow of your boat. To rename a source, you must be in the applicable sonar view for the source. For example, to rename the Garmin ClearV sonar source, you must open the Garmin ClearV sonar view. 1 From the sonar view, select Menu > Sonar Setup > Source

> Rename Sources. 2 Enter the name. Creating a Waypoint on the Sonar Screen 1 From a sonar view, drag the screen or select 2 Select a location. 3 Select 4 If necessary, edit the waypoint information. Pausing the Sonar Display From a sonar view, select

. Viewing Sonar History You can scroll the sonar display to view historical sonar data. NOTE: Not all transducers save historical sonar data. 1 From a sonar view, drag the screen to the right. 2 Select Back to exit history. Sonar Sharing You can view the sonar data from all compatible sources on the Garmin Marine Network. You can view sonar data from a compatible external sonar module, such as a GCV sonar module. In addition, you can view the sonar data from other chartplotters that have a built-in sonar module. Each chartplotter on the network can display sonar data from every compatible sonar module and transducer on the network, no matter where the chartplotters and transducers are mounted on your boat. For example, from one GPSMAP 923 device mounted at the back of the boat, you can view the sonar data from another GPSMAP device and Garmin ClearV transducer mounted at the front of your boat. When sharing sonar data, the values of some sonar settings, such as Range and Gain, are synchronized across the devices on the network. The values of other sonar settings, such as the Appearance settings, are not synchronized and should be configured on each individual device. In addition, the scroll rates of the various traditional and Garmin ClearV sonar views are synchronized to make the split views more cohesive. NOTE: Using multiple transducers simultaneously can create cross talk, which can be removed by adjusting the Interference sonar setting. Adjusting the Level of Detail You can control the level of detail and noise shown on the sonar screen either by adjusting the gain for traditional transducers or by adjusting the brightness for Garmin ClearV transducers. If you want to see the highest intensity signal returns on the screen, you can lower the gain or brightness to remove lower intensity returns and noise. If you want to see all return information, you can increase the gain or brightness to see more information on the screen. This also increases noise, and can make it more difficult to recognize actual returns. 1 From a sonar view, select Menu. 2 Select Gain or Brightness. 3 Select an option:

To increase or decrease the gain or brightness manually, select Up or Down. To allow the chartplotter to adjust the gain or brightness automatically, select an automatic option. Adjusting the Color Intensity You can adjust the intensity of colors and highlight areas of interest on the sonar screen by adjusting the color gain for traditional transducers or the contrast for Garmin ClearV and SideV/ClearV transducers. This setting works best after you 28 Sonar Fishfinder have adjusted the level of detail shown on the screen using the gain or brightness settings. If you want to highlight smaller fish targets or create a higher intensity display of a target, you can increase the color gain or contrast setting. This causes a loss in the differentiation of the high intensity returns at the bottom. If you want to reduce the intensity of the return, you can reduce the color gain or contrast. 1 From a sonar view, select Menu. 2 Select an option:

While in the Garmin ClearV or SideV sonar view, select Contrast. While in a Panoptix LiveV sonar view, select Color Gain. While in another sonar view, select Sonar Setup >

Appearance > Color Gain. 3 Select an option:

To increase or decrease the color intensity manually, select Up or Down. To use the default setting, select Default. Sonar Recordings Recording the Sonar Display 1 Insert a memory card into the card slot. 2 From a sonar view, select Menu > Sonar Setup > Sonar Recording > Record Sonar. 15 minutes of sonar recording uses approximately 200 MB of space of the inserted memory card. An individual recording automatically ends after it reaches 4 GB in size. You can record sonar data until the card reaches capacity. Stopping the Sonar Recording Before you can stop recording sonar, you must begin recording it (Recording the Sonar Display, page 29). From a sonar view, select Menu > Sonar Setup > Sonar Recording > Stop Recording. Deleting a Sonar Recording 1 Insert a memory card into the card slot. 2 From a sonar view, select Menu > Sonar Setup > Sonar Recordings > View Recordings. 3 Select a recording. 4 Select Review > Delete. Playing Sonar Recordings Before you can play back the sonar recordings, you must download and install the HomePort application and record sonar data onto a memory card. 1 Remove the memory card from the device. 2 Insert the memory card into a card reader attached to a computer. 3 Open the HomePort application. 4 Select a sonar recording from your device list. 5 Right-click the sonar recording in the lower pane. 6 Select Playback. Traditional, Garmin ClearV, and SideV Sonar Setup NOTE: Not all options and settings apply to all models, sounder modules, and transducers. NOTE: These settings do not apply to Panoptix transducers. From a sonar view, select Menu > Sonar Setup. Scroll Speed: Sets the rate at which the sonar scrolls from right to left (Setting the Scroll Speed, page 29). In shallow water, you can select a slower scroll speed to extend the length of time the information is displayed on screen. In deeper water, you can select a faster scroll speed. Automatic scroll speed adjusts the scrolling speed to the speed the boat is traveling. Noise Reject: Reduces the interference and the amount of clutter shown on the sonar screen (Sonar Noise Rejection Settings, page 30). Appearance: Configures the appearance of the sonar screen

(Sonar Appearance Settings, page 30). Alarms: Sets sonar alarms (Sonar Alarms, page 30). Advanced: Configures various sonar display and data source settings (Advanced Sonar Settings, page 31). Not applicable to Garmin ClearV or SideV sonar views. Installation: Configures the transducer (Traditional, Garmin ClearV, and SideV Transducer Installation Settings, page 31). Setting the Zoom Level on the Sonar Screen 1 From a sonar view, select Menu > Zoom >

2 Select an option:

> Mode. To set the depth and zoom automatically, select Auto. If necessary, select Set Zoom to modify the zoom setting. Select View Up or View Down to set the depth range of the magnified area, and select Zoom In or Zoom Out to increase or decrease the magnification of the magnified area. To set the depth range of the magnified area manually, select Manual. If necessary, select Set Zoom to modify the zoom setting. Select View Up or View Down to set the depth range of the magnified area, and select Zoom In or Zoom Out to increase or decrease the magnification of the magnified area. To magnify one particular area of the screen, select Magnify. If necessary, select Magnify to increase or decrease the magnification level. TIP: You can drag the magnification box to a new location on the screen. To zoom in on the sonar data from the bottom depth, select Bottom Lock. If necessary, select Span to adjust the depth and placement of the bottom lock area. To cancel the zoom, deselect the Zoom option. Setting the Scroll Speed You can set the rate at which the sonar image moves across the screen. A higher scroll speed shows more detail until there is no additional detail to show, at which point it starts stretching out the existing detail. This can be useful while moving or trolling, or when you are in very deep water where the sonar is pinging very slowly. A lower scroll speed displays sonar information on the screen longer. For most situations, the Default setting provides a good balance between a quickly scrolling image and less distorted targets. 1 From a sonar view, select Menu > Sonar Setup > Scroll Speed. 2 Select an option:

To adjust the scroll speed automatically using speed-over-

ground or water speed data, select Auto. The Auto setting selects a scroll rate to match the boat speed, so targets in the water are drawn with the correct aspect ratio and appear less distorted. When viewing Garmin ClearV or SideV sonar views or searching for structure, it is recommend to use the Auto setting. Sonar Fishfinder 29 To scroll faster, select Up. To scroll more slowly, select Down. Adjusting the Range of the Depth or Width Scale You can adjust the range of the depth scale traditional and Garmin ClearV sonar views and the range of the width scale for the SideV sonar view. Allowing the device to adjust the range automatically keeps the bottom within the lower or outer third of the sonar screen, and can be useful for tracking a bottom that has minimal or moderate terrain changes. Manually adjusting the range enables you to view a specified range, which can be useful for tracking a bottom that has large terrain changes, such as a drop-offs or cliffs. The bottom can appear on the screen as long as it appears within the range you have set. 1 From a sonar view, select Menu > Range. 2 Select an option:

To allow the chartplotter to adjust the range automatically, select Auto. Down. To increase or decrease the range manually, select Up or TIP: From the sonar screen, you can select manually adjust the range. TIP: When viewing multiple sonar screens, you can select Select to choose the active screen. or to Sonar Noise Rejection Settings From a sonar view, select Menu > Sonar Setup > Noise Reject. Interference: Adjusts the sensitivity to reduce the effects of interference from nearby sources of noise. The lowest interference setting that achieves the desired improvement should be used to remove interference from the screen. Correcting installation issues that cause noise is the best way to eliminate interference. Color Limit: Hides part of the color palette to help eliminate fields of weak clutter. By setting the color limit to the color of the undesired returns, you can eliminate the display of undesired returns on the screen. Smoothing: Removes noise that is not part of a normal sonar return, and adjusts the appearance of returns, such as the bottom. When smoothing is set to high, more of the low-level noise remains than when using the interference control, but the noise is more subdued because of averaging. Smoothing can remove speckle from the bottom. Smoothing and interference work well together to eliminate low-level noise. You can adjust the interference and smoothing settings incrementally to remove undesirable noise from the display. Surface Noise: Hides surface noise to help reduce clutter. Wider beam widths (lower frequencies) can show more targets, but can generate more surface noise. TVG: Adjusts the time varying gain, which can reduce noise. This control is best used for situations when you want to control and suppress clutter or noise near the water surface. It also allows for the display of targets near the surface that are otherwise hidden or masked by surface noise. Sonar Appearance Settings From a sonar view, select Menu > Sonar Setup > Appearance. Color Scheme: Sets the color scheme. Color Gain: Adjusts the intensity of colors (Adjusting the Color Intensity, page 28). A-Scope: Displays a vertical flasher along the right side of the screen that shows instantaneously the range to targets along a scale. Depth Line: Shows a quick-reference depth line. Edge: Highlights the strongest signal from the bottom to help define the hardness or softness of the signal. Fish Symbols: Sets how the sonar interprets suspended targets. Shows suspended targets as symbols and background sonar information. Shows suspended targets as symbols with target depth information and background sonar information. Shows suspended targets as symbols. Shows suspended targets as symbols with target depth information. Pic. Advance: Allows the sonar picture to advance faster by drawing more than one column of data on the screen for each column of sounder data received. This is especially helpful when you are using the sounder in deep water, because the sonar signal takes longer to travel to the water bottom and back to the transducer. The 1/1 setting draws one column of information on the screen per sounder return. The 2/1 setting draws two columns of information on the screen per sounder return, and so on for the 4/1 and 8/1 settings. Echo Stretch: Adjusts the size of the echoes on the screen to make it easier to see separate returns on the screen. When targets are difficult to see target returns more pronounced and easier to see on the screen. If the echo stretch value is too high, the targets blend together. If the value is too low more difficult to see.

, the targets are small and

, echo stretch makes the You can use echo stretch and filter width together to obtain the preferable resolution and noise reduction. With echo stretch and filter width set to low, the display has the highest resolution, but is the most susceptible to noise. With echo stretch set to high and filter width set to low, the display has a lower resolution, but has wider targets. With echo stretch and filter width set to high, the display has the lowest resolution, but is the least susceptible to noise. It is not recommended to set echo stretch to low and filter width to high. Overlay Data: Sets the data shown on the sonar screen. Sonar Alarms NOTE: Not all options are available on all transducers. From an applicable sonar view, select Menu > Sonar Setup >

Alarms. You can also open the sonar alarms by selecting Settings >

Alarms > Sonar. Shallow Water: Sets an alarm to sound when the depth is less Deep Water: Sets an alarm to sound when the depth is greater than the specified value. than the specified value. FrontV Alarm: Sets an alarm to sound when the depth in front of the vessel is less than the specified value, which can help 30 Sonar Fishfinder you avoid running aground (Setting the FrontV Depth Alarm, page 33). This alarm is available only with Panoptix FrontV transducers. Water Temp.: Sets an alarm to sound when the transducer reports a temperature that is 2F (1.1C) above or below the specified temperature. Contour: Sets an alarm to sound when the transducer detects a suspended target within the specified depth from the surface of the water and from the bottom. Fish Fish: Sets an alarm to sound when the device detects a suspended target. detected. fish are detected. detected. sets the alarm to sound when fish of all sizes are sets the alarm to sound only when medium or large sets the alarm to sound only when large fish are Advanced Sonar Settings From a Traditional sonar view, select Menu > Sonar Setup >

Advanced. Shift: Allows you to set the depth range on which the sonar is focused. This allows you to zoom in a higher resolution in the focused depth. When using shift, bottom tracking may not work effectively, because the sonar looks for data within the depth range of the focused area, which may not include the bottom. Using shift also can impact the scroll speed, because data outside the depth range of the focused area is not processed, which reduces the time required to receive and display the data. You can zoom in to the focused area, which enables you to evaluate target returns more closely at a higher resolution than just zooming alone. Btm. Srch. Limit: Limits the search for the bottom to the depth selected when the Range setting is set to Auto. To minimize the length of time it takes to find the bottom, you can select a depth to limit the search for the bottom. The device will not search for the bottom deeper than the selected depth. Traditional, Garmin ClearV, and SideV Transducer Installation Settings From a Traditional, Garmin ClearV, or SideV sonar view, select Menu > Sonar Setup > Installation. Transmit Rate: Sets the length of time between sonar pings. Increasing the transmit rate increases the scroll speed, but it may also increase self-interference. Reducing the transmit rate increases the spacing between transmit pulses and can resolve self-interference. This option is available on the Traditional sonar view only. Transmit Power: Reduces transducer ringing near the surface. A lower transmit power value reduces transducer ringing, but can also reduce the strength of the returns. This option is available on the Traditional sonar view only. Filter Width: Defines the edges of the target. A shorter filter more clearly defines the edges of the targets but may allow more noise. A longer filter creates softer target edges and may also reduce noise. This option is available on the Traditional sonar view only. Flip Left/Right: Switches the SideV view orientation from left to right. This option is available on the SideV sonar view only. Restore Sonar Defaults: Restores the sonar settings to the factory default values. Allows you to change the transducer, view details about the transducers, and save details to a memory card. Sonar Frequencies NOTE: The frequencies available depend on the device and trandsucers being used. Adjusting the frequency helps adapt the sonar for your particular goals and the present depth of the water. Higher frequencies use narrow beam widths, and are better for high-speed operation and rough sea conditions. Bottom definition and thermocline definition can be better when using a higher frequency. Lower frequencies use wider beam widths, which can let the fisherman see more targets, but could also generate more surface noise and reduce bottom signal continuity during rough sea conditions. Wider beam widths generate larger arches for fish target returns, making them ideal for locating fish. Wider beam widths also perform better in deep water, because the lower frequency has better deep water penetration. CHIRP frequencies allow you to sweep each pulse through a range of frequencies, resulting in better target separation in deep water. CHIRP can be used to distinctly identify targets, like individual fish in a school, and for deep water applications. CHIRP generally performs better than single frequency applications. Because some fish targets may show up better using a fixed frequency, you should consider your goals and water conditions when using CHIRP frequencies. Some transducers also provide the ability to customize preset frequencies for each transducer element, which enables you to change the frequency quickly using the presets as the water and your goals change. Viewing two frequencies concurrently using the split-frequency view allows you to see deeper with the lower frequency return and, at the same time, see more detail from the higher frequency return. NOTICE Always be aware of local regulations on sonar frequencies. For example, to protect orca whale pods, you might be prohibited from using frequencies between 50 to 80 khz with in mile of an orca whale pod. It is your responsibility to use the device in compliance with all applicable laws and ordinances. Selecting the Transducer Frequency NOTE: You cannot adjust the frequency for all sonar views and transducers. You can select which frequencies appear on the sonar screen. NOTICE Always be aware of local regulations on sonar frequencies. For example, to protect orca whale pods, you might be prohibited from using frequencies between 50 to 80 khz with in mile of an orca whale pod. It is your responsibility to use the device in compliance with all applicable laws and ordinances. 1 From a sonar view, select Menu > Frequency. 2 Select a frequency suited to your needs and water depth. For more information on frequencies, see Sonar Frequencies, page 31. Creating a Frequency Preset NOTE: Not available with all transducers. You can create a preset to save a specific sonar frequency, which allows you to change frequencies quickly. 1 From a sonar view, select Menu > Frequency. 2 Select Manage Frequencies > New Preset. 3 Enter a frequency. Turning On the A-Scope NOTE: This feature is available in the Traditional sonar views. Sonar Fishfinder 31 The a-scope is a vertical flasher along the right side of the view, showing you what is underneath the transducer right now. You can use the a-scope to identify target returns that may be missed when the sonar data is quickly scrolling across the screen, such as when your boat is moving at high speeds. It can also be helpful for detecting fish that are close to the bottom. The a-scope above shows fish returns return 1 From a sonar view, select Menu > Sonar Setup >

. and a soft bottom Appearance > A-Scope > On. 2 Select a hold time. You can increase the hold time to increase the length of time the sonar returns are displayed. Panoptix Sonar Setup Zooming in a Panoptix LiveV or LiveScope Sonar View You can zoom in on the Panoptix LiveV and LiveScope 2D sonar views. NOTE: The scrolling history is hidden while the screen is in zoom mode. 1 From a Panoptix LiveV or LiveScope 2D sonar view, spread two fingers apart to zoom in on the area. An inset window the full-screen image. The boxed area the location of the zoomed area. appears and displays a small version of in the inset shows 2 If necessary, tap or drag within the inset window to view a different area of the full-screen view. 3 If necessary, spread two fingers apart to zoom in. 4 If necessary, pinch two fingers together to zoom out. To exit zoom mode, select Back or pinch two fingers together to zoom out until the screen returns to a full-screen view. Adjusting the RealV Viewing Angle and Zoom Level You can change the viewing angle of the RealV sonar views. You can also zoom in and out of the view. From a RealV sonar view, select an option:

To adjust the viewing angle diagonally, select To adjust the viewing angle horizontally, select To adjust the viewing angle vertically, select

. To adjust the viewing angle, swipe the screen in any

. direction. To zoom in, spread two fingers apart. To zoom out, pinch two fingers together. Adjusting the RealV Sweep Speed You can update how quickly the transducer sweeps back and forth. A faster sweep rate creates a less detailed image, but the screen refreshes faster. A slower sweep rate creates a more detailed image, but the screen refreshes more slowly. NOTE: This feature is not available for the RealV 3D Historical sonar view. 1 From a RealV sonar view, select Menu > Sweep Speed. 2 Select an option. LiveV Forward and FrontV Sonar Menu From the LiveV Forward or FrontV sonar view, select Menu. Gain: Controls the level of detail and noise shown on the sonar screen. If you want to see the highest intensity signal returns on the screen, you can lower the gain to remove lower intensity returns and noise. If you want to see all return information, you can increase the gain to see more information on the screen. This also increases noise, and can make it more difficult to recognize actual returns. Depth Range: Adjusts the range of the depth scale. Allowing the device to adjust the range automatically keeps the bottom within the lower portion of the sonar screen, and can be useful for tracking a bottom that has minimal or moderate terrain changes. Manually adjusting the range enables you to view a specified range, which can be useful for tracking a bottom that has large terrain changes, such as a drop-offs or cliffs. The bottom can appear on the screen as long as it appears within the range you have set. Forward Range: Adjusts the range of the forward scale. Allowing the device to adjust the range automatically adjusts the forward scale in relation to the depth. Manually adjusting the range enables you to view a specified range. The bottom can appear on the screen as long as it appears within the range you have set. Manually reducing this option can reduce the effectiveness of the FrontV Alarm, reducing your reaction time to low depth readings. Transmit Angle: Adjusts the focus of the transducer to the port or starboard side. This feature is available only with RealV capable Panoptix transducers, such as the PS30, PS31, and PS60. Transmit: Stops the active transducer from transmitting. FrontV Alarm: Sets an alarm to sound when the depth in front of the vessel is less than the specified value (Setting the FrontV Depth Alarm, page 33). This is available only with Panoptix FrontV transducers. Sonar Setup: Adjusts the setup of the transducer and the appearance of the sonar returns. Edit Overlays: Adjusts the data shown on the screen

(Customizing the Data Overlays, page 5). Setting the LiveV and FrontV Transducer Transmit Angle This feature is available only with RealV capable Panoptix transducers, such as the PS30, PS31, and PS60. You can change the transducer transmit angle to aim the transducer at a particular area of interest. For example, you might aim the transducer to follow a bait ball or focus on a tree as you pass it. 1 From a LiveV or FrontV sonar view, select Menu >

Transmit Angle. 2 Select an option. 32 Sonar Fishfinder Setting the FrontV Depth Alarm WARNING The FrontV depth alarm is a tool for situational awareness only, and may not prevent groundings in all circumstances. It is the obligation of the vessel operator to ensure safe operation of the vessel. This alarm is available only with Panoptix FrontV transducers. You can set an alarm to sound when the depth is below a specified level. For best results, you should set the bow offset when using the front collision alarm (Setting the Bow Offset, page 34). 1 From the FrontV sonar view, select Menu > FrontV 2 Select On. 3 Enter the depth at which the alarm is triggered, and select Alarm. Done. On the FrontV screen, a depth line shows the depth at which the alarm is set. The line is green when you are in a safe depth. The line turns yellow when you are going faster than the forward range gives you time to react (10 seconds). It turns red and sounds an alarm when the system detects an obstruction or the depth is less than the entered value. The ability to effectively avoid running aground with FrontV sonar decreases as your speed rises above 8 knots. CAUTION LiveV and FrontV Appearance Settings From a LiveV or FrontV Panoptix sonar view, select Menu >

Sonar Setup > Appearance. Color Scheme: Sets the color palette. Color Gain: Adjusts the intensity of colors shown on the screen. You can select a higher color gain value to see targets higher in the water column. A higher color gain value also allow you to differentiate low intensity returns higher in the water column, but this causes a loss in the differentiation of the returns at the bottom. You can select a lower color gain value when targets are near the bottom, to help you distinguish between targets and high intensity returns such as sand, rock, and mud. Trails: Sets the how long the trails appear on the screen. The trails show the movement of the target. Bottom Fill: Colors the bottom brown to distinguish it from the water returns. Grid Overlay: Shows a grid of range lines. Scroll History: Shows the sonar history in a traditional sonar view. points. RealV Appearance Settings From a RealV sonar view, select Menu > Sonar Setup >

Appearance. Point Colors: Sets a different color palette for the sonar return Bottom Colors: Sets the color scheme for the bottom. Bottom Style: Sets the style for the bottom. When you are in deep water, you can select the Points option and manually set the range to a shallower value. Color Key: Shows a legend of the depths the colors represent. LiveScope and Perspective Sonar Menu From the LiveScope or Perspective sonar view, select Menu. Gain: Controls the level of detail and noise shown on the sonar screen. If you want to see the highest intensity signal returns on the screen, you can lower the gain to remove lower intensity returns and noise. If you want to see all return information, you can increase the gain to see more information on the screen. Increasing the gain also increases noise, and can make it more difficult to recognize actual returns. Depth Range: Adjusts the range of the depth scale. Allowing the device to adjust the range automatically keeps the bottom within the lower portion of the sonar screen, and can be useful for tracking a bottom that has minimal or moderate terrain changes. Manually adjusting the range enables you to view a specified range, which can be useful for tracking a bottom that has large terrain changes, such as a drop-offs or cliffs. The bottom can appear on the screen as long as it appears within the range you have set. Available in LiveScope sonar view. Forward Range: Adjusts the range of the forward scale. Allowing the device to adjust the range automatically adjusts the forward scale in relation to the depth. Manually adjusting the range enables you to view a specified range. The bottom can appear on the screen as long as it appears within the range you have set. Available in LiveScope sonar view. Range: Adjust the range. Allowing the device to adjust the range automatically keeps the bottom within the lower or outer third of the sonar screen, and can be useful for tracking a bottom that has minimal or moderate terrain changes. Manually adjusting the range enables you to view a specified range, which can be useful for tracking a bottom that has large terrain changes, such as a drop-offs or cliffs. The bottom can appear on the screen as long as it appears within the range you have set. Available in Perspective sonar view. Transmit: Stops the active transducer from transmitting. Sonar Setup: Adjusts the setup of the transducer and the appearance of the sonar returns (LiveScope and Perspective Sonar Setup, page 33). Edit Overlays: Adjusts the data shown on the screen

(Customizing the Data Overlays, page 5). LiveScope and Perspective Sonar Setup From the LiveScope or Perspective sonar view, select Menu >

Sonar Setup. Appearance: Configures the appearance of the sonar screen

(LiveScope and Perspective Appearance Settings, page 34). Noise Reject: Reduces noise and interference and attempts to remove returns that are not actually targets in the water. Ghost Reject: Reduces the occurrence of "ghost" images, which are duplicated or reflected images that are not actually targets in the water. "Ghost" images are caused by strong sonar returns, such as the bottom. Shallow water and hard bottoms generally have stronger returns and may cause

"ghost" images to occur more obviously. Adjusting the Ghost Reject and Noise Reject settings together reduces the occurrence of "ghost" images most effectively. TVG: Adjusts the time varying gain, which can reduce noise. This control is best used for situations when you want to control and suppress clutter or noise near the water surface. It also allows for the display of targets near the surface that are otherwise hidden or masked by surface noise. Overlay Data: Sets the data shown on the sonar screen. Sonar Fishfinder 33 Installation: Configures the transducer (Traditional, Garmin Focus: Adjusts the sonar view to compensate for the speed of ClearV, and SideV Transducer Installation Settings, page 31). LiveScope and Perspective Appearance Settings From the LiveScope or Perspective sonar view, select Menu >

Sonar Setup > Appearance. Color Scheme: Sets the color palette. Color Gain: Adjusts the contrast of colors shown on the screen. You can select a higher color gain value to see minor variances in targets with large color changes. You can select a lower color gain value to see more similar colors in the same situation. Trails: Sets the how long the trails appear on the screen. The trails show the movement of the target. sound in water. The Auto setting uses the temperature of the water to calculate the speed of sound. This applies to LiveScope transducers. Restore Sonar Defaults: Restores the sonar settings to the factory default values. Setting the Bow Offset For forward view Panoptix transducers, you can enter a bow offset to compensate the forward distance readings for the transducer installation location. This allows you to view the forward distance from the bow instead of the transducer installation location. This feature applies to Panoptix transducers in the FrontV, LiveV Forward, and RealV 3D Forward sonar views. 1 Measure the horizontal distance from the transducer to the Bottom Fill: Colors the bottom brown to distinguish it from the water returns. Not available in Perspective mode. bow. Grid Overlay: Shows or hides grids of range lines. The Grid option shows a square grid. The Radial option shows a circular grid with radial angle lines. Scroll History: Shows the sonar history on the side of the screen. Not available in Perspective mode. Boat Icon: Shows or hides the icon of the boat in the upper-right corner. Panoptix Transducer Installation Settings From a Panoptix sonar view, select Menu > Sonar Setup >

Installation. Install Depth: Sets the depth below the water line where the Panoptix transducer is mounted. Entering the actual depth at which the transducer is mounted results in a more accurate visual presentation of what is in the water. Bow Offset: Sets the distance between the bow and the forward view Panoptix transducer installation location. This allows you to view the forward distance from the bow instead of the transducer location. This applies to Panoptix transducers in the FrontV, LiveV Forward, and RealV 3D Forward sonar views. Beam Width: Sets the width of the down view Panoptix transducer beam. Narrow beam widths allow you to see deeper and farther. Wider beam widths allow you to see more coverage area. This applies to Panoptix transducers in the FrontV, LiveV Down, and LiveV Forward sonar views. Use AHRS: Enables the internal attitude heading and reference system (AHRS) sensors to detect the installation angle of the Panoptix transducer automatically. When this setting is turned off, you can enter the specific installation angle for the transducer using the Pitch Angle setting. Many forward view transducers are installed at a 45-degree angle and down view transducers are installed at a zero-degree angle. Flipped: Sets the orientation of the Panoptix sonar view when the down view transducer is installed with the cables pointing toward the port side of the boat. This applies to Panoptix transducers in the LiveV Down, RealV 3D Down, and RealV 3D Historical sonar views. Calibrate Compass: Calibrates the internal compass in the Panoptix transducer (Calibrating the Compass, page 34). This applies to Panoptix transducers with an internal compass, such as the PS21-TR transducer. Orientation: Controls if the transducer is in down or forward installation mode. The Auto setting uses the AHRS sensor to determine the orientation. This applies to PS22 and LiveScope transducers. 2 From an applicable sonar view, select Menu > Sonar Setup

> Installation > Bow Offset. 3 Enter the distance measured, and select Done. On the applicable sonar view, the forward range shifts by the distance you entered. Calibrating the Compass Before you can calibrate the compass, the transducer must be installed on the shaft far enough away from the trolling motor to avoid magnetic interference, and deployed in the water. Calibration must be of sufficient quality to enable the internal compass. NOTE: To use the compass, you must mount the transducer on the transom or the trolling motor shaft. The compass may not work when you mount the transducer on the motor. NOTE: For best results, you should use a heading sensor such as the SteadyCast heading sensor. The heading sensor shows the direction the transducer is pointing relative to the boat. NOTE: Compass calibration is available only for transducers with an internal compass, such as the PS21-TR transducer. You can begin turning your boat before calibrating, but you must fully rotate your boat 1.5 times during calibration. 1 From an applicable sonar view, select Menu > Sonar Setup

> Installation. 2 If necessary, select Use AHRS to turn on the AHRS sensor. 3 Select Calibrate Compass. 4 Follow the on-screen instructions. 34 Sonar Fishfinder Radar WARNING The marine radar transmits microwave energy that has the potential to be harmful to humans and animals. Before beginning radar transmission, verify that the area around the radar is clear. The radar transmits a beam approximately 12 above and below a line extending horizontally from the center of the radar. To avoid possible personal injury, do not look directly at the antenna at close range when the radar is transmitting. Eyes are the most sensitive part of the body to electromagnetic energy. When you connect your compatible chartplotter to an optional Garmin marine radar, such as a GMR Fantom 6 radar or a GMR 24 xHD, you can view more information about your surroundings. The radar transmits a narrow beam of microwave energy as it rotates to a 360 pattern. When the transmitted energy contacts a target, some of that energy is reflected back to the radar. Radar Interpretation Reading and interpreting the radar display takes practice. The more you use the radar, the better you will become at relying on the radar display when you really need it. Radar can be useful in many situations, such as avoiding collisions when you have limited visibility, for example when it is dark or foggy, tracking weather, seeing what is ahead of you, and locating birds and fish. The radar overlay feature can help you interpret the radar display more easily, because it overlays the radar returns on top of the chart. This can help you identify the difference between a radar return of a land mass, bridge, or rain cloud. Showing the AIS vessels on the radar overlay can also help you identify features on the radar display. In the screenshot below, the radar overlay is turned on. This screen also shows a video feed. We can easily identify a few items on the radar screen. Land Vessel Radar Overlay When you connect your chartplotter to an optional Garmin marine radar, you can use overlay radar information on the Navigation chart or on the Fishing chart. Data appears on the radar overlay based on the most recently used radar mode and all settings configurations applied to the radar overlay are also applied to the last-used radar mode. Radar Overlay and Chart Data Alignment When using the Radar overlay, the chartplotter aligns radar data with chart data based on the boat heading, which is based by default on data from a magnetic heading sensor connected using a NMEA 0183 or NMEA 2000 network. If a heading sensor is not available, the boat heading is based on GPS tracking data. GPS tracking data indicates the direction in which the boat is moving, not the direction in which the boat is pointing. If the boat is drifting backward or sideways due to a current or wind, the Radar overlay may not perfectly align with the chart data. This situation should be avoided by using boat-heading data from an electronic compass. If the boat heading is based on data from a magnetic heading sensor or an automatic pilot, the heading data could be compromised due to incorrect setup, mechanical malfunction, magnetic interference, or other factors. If the heading data is compromised, the Radar overlay may not align perfectly with the chart data. Transmitting Radar Signals NOTE: As a safety feature, the radar enters standby mode after it warms up. This gives you an opportunity to verify the area around the radar is clear before beginning radar transmission. 1 With the chartplotter off, connect your radar as described in the radar installation instructions. 2 Turn on the chartplotter. If necessary, the radar warms up and a countdown alerts you when the radar is ready. 3 Select Radar. 4 Select a radar mode. A countdown message appears while the radar is starting up. 5 Select Menu > Transmit Radar. Stopping the Transmission of Radar Signals From a radar screen, select Menu > Radar To Standby. TIP: Press quickly stop radar transmission.

> Radar To Standby from any screen to Setting Up the Timed Transmit Mode To help conserve power, you can set up time intervals in which the radar will transmit and not transmit (standby) signal transmissions. NOTE: This feature is not available in dual radar modes. 1 From a radar screen, select Menu > Radar Options > Timed Transmit. 2 Select Timed Transmit to enable the option. 3 Select Stdby Time, enter the time interval between radar signal transmissions, and select Done. 4 Select Transmit Time, enter the duration of each radar signal transmission, and select Done. Enabling and Adjusting a Radar No Transmit Zone You can indicate areas within which the radar scanner does not transmit signals. NOTE: GMR Fantom and xHD2 radar models support two no-

transmit zones. Most other GMR radar models support one no-

transmit zone. GMR 18 HD+ radar models do not support no-

transmit zones. 1 From a radar screen, select Menu > Radar Setup >

Installation > No Transmit Zone. The no-transmit zone is indicated by a shaded area on the radar screen. 2 Select Angle 1, and select the new location for the first 3 Select Angle 2, and select the new location for the second angle. angle. 4 Select Done. 5 If necessary, repeat for the second zone. Adjusting the Radar Range The range of the radar signal indicates the length of the pulsed signal transmitted and received by the radar. As the range increases, the radar transmits longer pulses in order to reach Radar 35 distant targets. Closer targets, especially rain and waves, also reflect the longer pulses, which can add noise to the Radar screen. Viewing information about longer-range targets can also decrease the amount of space available on the Radar screen for viewing information about shorter-range targets. Select Select to decrease the range. to increase the range. Tips for Selecting a Radar Range Determine what information you need to see on the Radar screen. For example, do you need information about nearby weather conditions or targets and traffic, or are you more concerned about distant weather conditions?

Assess the environmental conditions where the radar is being used. Especially in inclement weather, longer-range radar signals can increase the clutter on the Radar screen and make it more difficult to view information about shorter-range targets. In rain, shorter-range radar signals can enable you to view information about nearby objects more effectively, if the rain clutter setting is configured optimally. Select the shortest effective range, given your reason for using radar and the present environmental conditions. MotionScope Doppler Radar Technology The GMR Fantom radar uses the Doppler effect to detect and highlight moving targets to help you avoid potential collisions, find flocks of birds, and track weather formations. The Doppler effect is the frequency shift in the radar echo due to the relative motion of the target. This allows for instant detection of any targets moving toward or away from the radar. The MotionScope feature highlights the moving targets on the radar display so you can navigate around other boats or severe weather, or toward fishing spots where birds are feeding at the surface. The moving targets are color-coded so you can tell at a glance which targets are moving toward or away from you. On most color schemes, green indicates the target is moving away from you and red indicates the target is moving toward you. On some models, you can also adjust the M-Scope Sensitivity setting to change the speed threshold for target highlighting. A higher setting highlights slower targets, and a lower setting highlights only faster targets. Enabling a Guard Zone You can enable a guard zone to alert you when anything comes within a specified area around your boat. From a radar screen, select Menu > Radar Options > Guard Zone. Defining a Circular Guard Zone Before you can define the boundaries of the guard zone, you must enable a guard zone (Enabling a Guard Zone, page 36). You can define a circular guard zone that completely surrounds your boat. 1 From a radar screen, select Menu > Radar Options > Guard Zone >

> Circle. 2 Select the location of the outer guard zone circle. 3 Select the location of the inner guard zone circle to define the width of the guard zone. Defining a Partial Guard Zone Before you can define the boundaries of the guard zone, you must enable a guard zone (Enabling a Guard Zone, page 36). You can define the boundaries of a guard zone that does not completely surround your boat. 1 From a radar screen, select Menu > Radar Options > Guard Zone >

> Corner 1. 2 Touch and drag the location of the outer guard-zone corner

. 3 Select Corner 2. 4 Select the location of the inner guard-zone corner to define the width of the guard zone. 5 Select Done. MARPA Mini-automatic radar plotting aid (MARPA) enables you to identify and track targets and is primarily used for collision avoidance. To use MARPA, you assign a MARPA tag to a target. The radar system automatically tracks the tagged object and provides you with information about the object, including the range, bearing, speed, GPS heading, nearest approach, and time to nearest approach. MARPA indicates the status of each tagged object (acquiring, lost, tracking, or dangerous), and the chartplotter can sound a collision alarm if the object enters your safe zone. Before you can use MARPA, you must have a heading sensor connected and an active GPS signal. The heading sensor must provide the NMEA 2000 parameter group number (PGN) 127250 or the NMEA 0183 HDM or HDG output sentence. MARPA Targeting Symbols Acquiring a target. Concentric, dashed green rings radiate from the target while the radar is locking onto it. Target has been acquired. A solid green ring indicates the location of a target that the radar has locked onto. A dashed green line attached to the circle indicates the projected course over ground or the GPS heading of the target. Dangerous target is in range. A red ring flashes from the target while an alarm sounds and a message banner appears. After the alarm has been acknowledged, a solid red dot with a dashed red line attached to it indicates the location and the projected course over ground or the GPS heading of the target. If the safe-zone collision alarm has been set to Off, the target flashes, but the audible alarm does not sound and the alarm banner does not appear. Target has been lost. A solid green ring with an X through it indicates that the radar could not lock onto the target. Closest point of approach and time to closest point of approach to a dangerous target. Acquiring MARPA Targets Automatically You can acquire MARPA targets automatically based on MotionScope, guard zones, or boundaries. 36 Radar 1 From a radar screen, select Menu > Layers > Other 1 From a radar screen, select Menu > Radar Options > VRM/

Vessels > MARPA > Auto Acquire. 2 Select

, and adjust additional settings (optional). 2 To adjust the VRM/EBL, select the arrows on the VRM/EBL Assigning a MARPA Tag to an Object Before you can use MARPA, you must have a heading sensor connected and an active GPS signal. The heading sensor must provide the NMEA 2000 parameter group number (PGN) 127250 or the NMEA 0183 HDM or HDG output sentence. 1 From a radar screen, select an object or location. 2 Select Acquire Tgt. > MARPA Target. Removing a MARPA Tag from a Targeted Object 1 From the Radar screen, select a MARPA target. 2 Select MARPA Target > Remove. Viewing Information about a MARPA-tagged Object You can view the range, bearing, speed, and other information about a MARPA-tagged object. 1 From a radar screen, select a targeted object. 2 Select MARPA Target. Viewing a List of AIS and MARPA Threats From any Radar screen or the Radar overlay, you can view and customize the appearance of a list of AIS and MARPA threats. 1 From a Radar screen, select Menu > Layers > Other Vessels. 2 Select an option:

To view a list of AIS threats, select AIS > AIS List. To view a list of MARPA threats, select MARPA >

MARPA List. 3 If necessary, select Display Options > Show, and select the type of threats to include in the list. Showing AIS Vessels on the Radar Screen AIS requires the use of an external AIS device and active transponder signals from other vessels. You can configure how other vessels appear on the Radar screen. If any setting (except the AIS display range) is configured for one radar mode, the setting is applied to every other radar mode. The details and projected heading settings configured for one radar mode are applied to every other radar mode and to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu >

Layers > Other Vessels > AIS. 2 Select an option:

To indicate the distance from your location within which AIS vessels appear, select Display Range, and select a distance. To show details about AIS-activated vessels, select Details > Show. To set the projected heading time for AIS-activated vessels, select Proj. Heading, and enter the time. VRM and EBL The variable range marker (VRM) and the electronic bearing line

(EBL) measure the distance and bearing from your boat to a target object. On the Radar screen, the VRM appears as a circle that is centered on the present location of your boat, and the EBL appears as a line that begins at the present location of your boat and intersects the VRM. The point of intersection is the target of the VRM and the EBL. Showing and Adjusting the VRM and the EBL You can adjust the diameter of the VRM and the angle of the EBL, which moves the intersection point of the VRM and the EBL. The VRM and the EBL configured for one mode are applied to all other radar modes. EBL. button. and the EBL 4 Select Done 3 Select a new location for the intersection point of the VRM Measuring the Range and Bearing to a Target Object Before you can adjust the VRM and the EBL, you must show them on the Radar screen (Showing and Adjusting the VRM and the EBL, page 37). 1 From a Radar screen, select the target location. 2 Select Measure. The range and the bearing to the target location appear in the upper-left corner of the screen. Echo Trails The echo trails feature enables you to track the movement of vessels on the radar display. As a vessel moves, you can see a faint trail of the vessel's wake. You can change the length of time the trail is displayed. NOTE: Depending upon the radar in use, the settings configured for use in one radar mode may or may not be applied to other radar modes or to the radar overlay. NOTE: This feature is not available on xHD open array or HD/HD+ radome models. Turning on Echo Trails From a radar screen, select Menu > Radar Options > Echo Trails > Display. Adjusting the Length of the Echo Trails 1 From a radar screen or the radar overlay, select Menu >

Radar Options > Echo Trails > Time. 2 Select the length of the trail. Clearing the Echo Trails You can remove the echo trails from the radar screen to reduce the clutter on the screen. From a radar screen, select Menu > Radar Options > Echo Trails > Clear Trails. Radar Settings NOTE: Not all options and settings are available on all radar and chartplotter models. NOTE: You can optimize the radar display for each radar mode. Radar Gain Adjusting Gain on the Radar Screen Automatically The automatic gain setting for each radar mode is optimized for that mode, and may differ from the automatic gain setting used for another mode. NOTE: Depending upon the radar in use, the gain setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. NOTE: Not all options are available on all radar models. Radar 37 1 From a radar screen or the radar overlay, select Menu >

Gain. 2 Select an option:

To adjust the gain automatically for changing conditions, select Auto Low or Auto High. To adjust the gain automatically to show birds over the surface of the water, select Auto Bird. NOTE: This option is not available on xHD open array or HD/HD+ radome models. Adjusting Gain on the Radar Screen Manually For optimal radar performance, you can manually adjust the gain. NOTE: Depending upon the radar in use, the gain setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu >

Gain. 2 Select Up to raise the gain, until light speckles appear across the Radar screen. Data on the Radar screen is refreshed every few seconds. As a result, the effects of manually adjusting the gain may not appear instantly. Adjust the gain slowly. 3 Select Down to lower the gain until the speckles disappear. 4 If boats, land, or other targets are within range, select Down to lower the gain until the targets begin to blink. 5 Select Up to raise the gain until the boats, land, or other targets appear steadily lit on the Radar screen. 6 Minimize the appearance of nearby large objects, if necessary. 7 Minimize the appearance of side-lobe echoes, if necessary. Minimizing Nearby Large-Object Interference Nearby targets of significant size, such as jetty walls, can cause a very bright image of the target to appear on the Radar screen. This image can obscure smaller targets located near it. NOTE: Depending upon the radar in use, the gain setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu >

Gain. 2 Select Down to lower the gain until the smaller targets are clearly visible on the Radar screen. Reducing the gain to eliminate nearby large-object interference may cause smaller or distant targets to blink or disappear from the Radar screen. Minimizing Side-Lobe Interference on the Radar Screen Side-lobe interference may appear to streak outward from a target in a semi-circular pattern. Side-lobe effects can be avoided by reducing the gain or reducing the radar range. NOTE: Depending upon the radar in use, the gain setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu >

Gain. 2 Select Down to lower the gain until the semi-circular, streaked pattern disappears from the Radar screen. Reducing the gain to eliminate side-lobe interference may cause smaller or distant targets to blink or disappear from the Radar screen. Radar Filter Settings Adjusting Sea Clutter on the Radar Screen You can adjust the appearance of clutter caused by choppy sea conditions. The sea clutter setting affects the appearance of nearby clutter and targets more than it affects the appearance of distant clutter and targets. A higher sea clutter setting reduces the appearance of clutter caused by nearby waves, but it can also reduce or eliminate the appearance of nearby targets. NOTE: Depending upon the radar in use, the sea clutter setting configured for use in one radar mode may or may not be applied to other radar modes or to the radar overlay. NOTE: Not all options and settings are available on all radar and chartplotter models. 1 From a radar screen or the radar overlay, select Menu >

Radar Filters > Sea Clutter. 2 Select an option:. Select an Auto option based on the sea conditions. Select Up or Down to adjust the appearance of sea clutter until other targets are clearly visible on the radar screen. Select a setting that reflects the present sea conditions. Clutter caused by sea conditions may still be visible. When using a compatible radar model, the chartplotter adjusts the sea clutter based on the sea conditions automatically. Adjusting Rain Clutter on the Radar Screen You can adjust the appearance of clutter caused by rain. Reducing the radar range also can minimize rain clutter

(Adjusting the Radar Range, page 35). The rain clutter setting affects the appearance of nearby rain clutter and targets more than it affects the appearance of distant rain clutter and targets. A higher rain clutter setting reduces the appearance of clutter caused by nearby rain, but it can also reduce or eliminate the appearance of nearby targets. NOTE: Depending upon the radar in use, the rain clutter settings configured for use in one radar mode may or may not be applied to other radar modes or to the radar overlay. 1 From a radar screen, select Menu > Radar Filters > Rain Clutter. 2 Select Up or Down to decrease or increase the appearance of nearby rain clutter until other targets are clearly visible on the radar screen. Clutter caused by rain may still be visible. Averaging Multiple Scans on the Radar Screen You can average the results of multiple scans on the radar screen. This can be an effective method to filter out noise and enhances the detection of consistent targets. Averaging is most effective when using a longer range. 1 From a radar screen or the radar overlay, select Menu >

Radar Filters > Scan Average. 2 Select an option. The High setting filters out the most noise. Radar Options Menu From a radar screen, select Menu > Radar Options. MotionScope: Uses the Doppler effect to detect and highlight moving targets to help you avoid potential collisions, find flocks of birds, and track weather formations (MotionScope Doppler Radar Technology, page 36). This option is only available on Fantom models. Pulse Exp.: Increases the duration of the transmit pulse, which helps maximize the energy directed toward targets. This helps to enhance the detection and identification of targets. This option is only available on xHD radome and xHD2 open array models. Target Size: Adjusts the size of targets, by adjusting the pulse compression processing. Select smaller targets for a sharp, high resolution radar image. Select larger targets to display larger echos for point targets, like boats and buoys. This option is only available on Fantom models. 38 Radar Echo Trails: Enables you to track the movement of vessels on the radar screen. This option is not available on xHD open array or HD/HD+ radome models. VRM/EBL: Shows the variable range marker (VRM) circle and the electronic bearing line (EBL) to allow you to measure the distance and bearing from your boat to a target object (VRM and EBL, page 37). Guard Zone: Sets a safe zone around your boat and sounds an alarm when anything enters the zone (Enabling a Guard Zone, page 36). Timed Transmit: Helps conserve power by transmitting radar signals at set intervals. Radar Setup Menu From a radar screen, select Menu > Radar Setup. Source: Selects the radar source when more than one radar is connected to the network. Chart Display: Shows the chart under the radar image. When enabled, the Layers menu appears. Orientation: Sets the perspective of the radar display. Crosstalk Rej.: Reduces the appearance of clutter caused by interference from another nearby radar source. Rotation Spd.: Sets the preferred speed at which the radar rotates. The High Speed option can be used to increase the refresh rate. In some situations, the radar automatically rotates at the normal speed to improve detection, for example, when a longer range is selected or when MotionScope or Dual range is used. Front-of-Boat Offset The front-of-boat offset compensates for the physical location of the radar scanner on a boat, if the radar scanner does not align with the bow-stern axis. Measuring the Potential Front-of-Boat Offset The front-of-boat offset compensates for the physical location of the radar scanner on a boat, if the radar scanner does not align with the bow-stern axis. 1 Using a magnetic compass, take an optical bearing of a stationary target located within viewable range. 2 Measure the target bearing on the radar. 3 If the bearing deviation is more than +/- 1, set the front-of-

boat offset. Setting the Front-of-Boat Offset Before you can set the front-of-boat offset, you must measure the potential front-of-boat offset. The front-of-boat offset setting configured for use in one radar mode is applied to every other radar mode and to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu >

Radar Setup > Installation > Front of Boat. 2 Select Up or Down to adjust the offset. Setting a Custom Park Position By default, the antenna is stopped perpendicular to the pedestal when it is not spinning. You can adjust this position. 1 From the radar screen, select Menu > Radar Setup >

Installation > Antenna Configuration > Park Position. Appearance: Sets the color scheme, look-ahead speed, and 2 Use the slider bar to adjust the position of the antenna when navigation appearance. stopped, and select Back. Installation: Allows you to configure the radar for the installation, such as setting the front of the boat and the antenna park position. Reducing Cross Talk Clutter on the Radar Screen You can reduce the appearance of clutter caused by interference from another nearby radar source, when the cross talk reject setting is on. NOTE: Depending upon the radar in use, the cross talk reject setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. From a Radar screen or the Radar overlay, select Menu >

Radar Setup > Crosstalk Rej.. Radar Appearance Settings From a radar screen, select Menu > Radar Setup >

Appearance. NOTE: These settings do not apply to the radar overlay. Bkgd. Color: Sets the color for the background. Frgd. Color: Sets the color scheme for the radar returns. Brightness: Sets the brightness of various radar features, such as range rings and tracking symbols. Look-Ahead Speed: Shifts your present location toward the bottom of the screen automatically as your speed increases. Enter your top speed for the best results. Radar Installation Settings Front of Boat: Compensates for the physical location of the radar when it is not on the boat axis (Front-of-Boat Offset, page 39). Antenna Configuration: Sets the radar antenna size and sets the position in which the radar stops (Setting a Custom Park Position, page 39). No Transmit Zone: Sets the area in which the radar does not transmit signals (Enabling and Adjusting a Radar No Transmit Zone, page 35). Radar My Vessel Layer Settings From a radar screen, select Menu > Layers > My Vessel. Heading Line: Shows an extension from the bow of the boat in the direction of travel on the radar screen. Range Rings: Shows the range rings that help you to visualize distances on the radar screen. Bearing Ring: Shows a bearing relative to your heading or based on a north reference, to help you determine the bearing to an object shown on the radar screen. Selecting a Different Radar Source 1 Select an option:

From a radar screen or the radar overlay, select Menu >

Radar Setup > Source. Select Settings > Communications > Preferred Sources > Radar. 2 Select the radar source. Changing the Radar Mode 1 From a combination screen or SmartMode layout with radar, select Menu > Radar Menu > Change Radar. 2 Select a radar mode. Autopilot WARNING You can use the autopilot feature only at a station installed next to a helm, throttle, and helm control device. You are responsible for the safe and prudent operation of your vessel. The autopilot is a tool that enhances your capability to operate your boat. It does not relieve you of the responsibility of safely operating your boat. Avoid navigational hazards and never leave the helm unattended. Autopilot 39 Always be prepared to promptly regain manual control of your boat. Learn to operate the autopilot on calm and hazard-free open water. Use caution when operating the autopilot near hazards in the water, such as docks, pilings, and other boats. The autopilot system continuously adjusts the steering of your boat to maintain a constant heading (heading hold). The system also allows manual steering and several modes of automatic-

steering functions and patterns. When the chartplotter is connected to a compatible Garmin autopilot system, you can engage and control the autopilot from the chartplotter. For information about compatible Garmin autopilot systems, go to garmin.com. When the chartplotter is connected to a compatible Yamaha autopilot system, you can control the autopilot from the chartplotter using the Yamaha autopilot screen and overlay bar

(Yamaha Autopilot, page 42). For information about compatible Yamaha autopilot systems, contact your Yamaha dealer. Opening the Autopilot Screen Before you can open the autopilot screen, you must have a compatible Garmin autopilot installed and configured. Select A/V, Gauges, Controls > Autopilot. Autopilot Screen Actual heading Intended heading (heading the autopilot is steering toward) Actual heading (when in standby mode) Intended heading (when engaged) Rudder position indicator (This functionality is available only when a rudder sensor is connected.) Adjusting the Step Steering Increment 1 From the Autopilot screen, select Menu > Autopilot Setup >

Step Turn Size. 2 Select an increment. Setting the Power Saver You can adjust the level of rudder activity. 1 From the autopilot screen, select Menu > Autopilot Setup >

Power Mode Setup > Power Saver. 2 Select a percentage. Selecting a higher percentage reduces rudder activity and heading performance. The higher the percentage, the more the course deviates before the autopilot corrects it. TIP: In choppy conditions at low speeds, increasing the Power Saver percentage reduces rudder activity. Enabling Shadow Drive NOTE: The Shadow Drive feature is not available on all autopilot models. From the autopilot screen, select Menu > Autopilot Setup >

Shadow Drive > Enabled. Selecting the Preferred Heading Source NOTICE For best results, use the autopilot CCU internal compass for the heading source. Using a third-party GPS compass can cause the data to be delivered erratically and may result in excessive delays. The autopilot needs timely information, and therefore cannot often use third-party GPS compass data for GPS location or speed. If a third-party GPS compass is used, the autopilot will likely report loss of navigation data and speed source periodically. If you have more than one heading source on the network, you can select a your preferred source. The source could be a compatible GPS compass or a magnetic heading sensor. 1 From the autopilot screen, select Menu > Autopilot Setup >

Preferred Sources 2 Select a source. If the selected heading source is unavailable, the autopilot screen does not display any data. Autopilot Overlay Bar NOTE: Not all options are available on all autopilot models. Autopilot mode Enables the heading hold Steers left Actual heading Rudder position indicator (available only when a rudder sensor is connected) Intended heading (heading the autopilot is steering toward) Steers right Engages the steering pattern Opens the full autopilot screen and menu Engaging the Autopilot When you engage the autopilot, the autopilot takes control of the helm and steers the boat to maintain your heading. From any screen, select Engage. Your intended heading shows in the center of the Autopilot screen. Adjusting the Heading with the Helm NOTE: You must enable the Shadow Drive feature before you can adjust the heading using the helm (Enabling Shadow Drive, page 40). With the autopilot engaged, manually steer the boat. The autopilot activates Shadow Drive mode. When you release the helm and manually maintain a specific heading for a few seconds, the autopilot resumes a heading hold at the new heading. Adjusting the Heading with the Chartplotter in Step Steering Mode Before you can steer your boat using the keys at the bottom of the autopilot screen, you must engage the autopilot (Engaging the Autopilot, page 40). Select <1 or 1> to initiate a single 1 turn. Select <<10 or 10>> to initiate a single 10 turn. Hold <1 or 1> to initiate a rate-controlled turn. The boat continues to turn until you let go of the key. 40 Autopilot Hold <<10 or 10>> to initiate a sequence of 10 turns. Steering Patterns WARNING You are responsible for the safe operation of your boat. Do not begin a pattern until you are certain that the water is clear of obstacles. The autopilot can steer the boat in preset patterns for fishing, and it can also perform other specialty maneuvers such as U-

turns and Williamson turns. Following the U-Turn Pattern You can use the u-turn pattern to turn the boat around 180 degrees and maintain the new heading. 1 From the autopilot screen, select Menu > Pattern Steering >

U-Turn. 2 Select Engage Port or Engage Starboard. Setting Up and Following the Circles Pattern You can use the circles pattern to steer the boat in a continuous circle, in a specified direction, and at a specified time interval. 1 From the autopilot screen, select Menu > Pattern Steering >

Circles. 2 If necessary, select Time, and select a time for the autopilot to steer one complete circle. 3 Select Engage Port or Engage Starboard. Setting Up and Following the Zigzag Pattern You can use the zigzag pattern to steer the boat from port to starboard and back, over a specified time and angle, across your present heading. 1 From the autopilot screen, select Menu > Pattern Steering >

Zigzag. 2 If necessary, select Amplitude, and select a degree. 3 If necessary, select Period, and select a length of time. 4 Select Engage Zigzag. Following the Williamson Turn Pattern You can use the Williamson turn pattern to steer the boat around with the intent of running alongside the location where the Williamson turn pattern was initiated. The Williamson turn pattern can be used in man overboard situations. 1 From the autopilot screen, select Menu > Pattern Steering >

Williamson Turn. 2 Select Engage Port or Engage Starboard. Following an Orbit Pattern You can use the orbit pattern to steer the boat in a continuous circle around the active waypoint. The size of the circle is defined by your distance from the active waypoint when you begin the orbit pattern. 1 From the autopilot screen, select Menu > Pattern Steering >

Orbit. 2 Select Engage Port or Engage Starboard. Setting Up and Following the Cloverleaf Pattern You can use the cloverleaf pattern to steer the boat to repeatedly pass over an active waypoint. When you begin the cloverleaf pattern, the autopilot drives the boat toward the active waypoint and begins the cloverleaf pattern. You can adjust the distance between the waypoint and the location where the autopilot turns the boat for another pass over the waypoint. The default setting turns the boat at a range of 1000 ft. (300 m) from the active waypoint. 1 From the autopilot screen, select Menu > Pattern Steering >

Cloverleaf. Autopilot 2 If necessary, select Length, and select a distance. 3 Select Engage Port or Engage Starboard. Setting Up and Following a Search Pattern You can use the search pattern to steer the boat in increasingly larger circles outward from the active waypoint, forming a spiral pattern. When you begin the search pattern, the autopilot drives the boat to the active waypoint and begins the pattern. You can adjust the distance between each circle in the spiral. The default distance between circles is 50 ft. (20 m). 1 From the autopilot screen, select Menu > Pattern Steering >

Search. 2 If necessary, select Search Spacing, and select a distance. 3 Select Engage Port or Engage Starboard. Cancelling a Steering Pattern Physically steer the boat. NOTE: Shadow Drive must be enabled to cancel a steering pattern by physically steering the boat. to cancel a pattern using step steering mode. Select Select Standby. or Adjusting the Autopilot Response The Response setting allows you to adjust the autopilot responsiveness for varying sea and wind conditions. 1 From the autopilot screen, select Menu > Response. 2 Adjust the rudder response. If you need the rudder to be more responsive and move quicker, increase the value. If the rudder is moving too much, decrease the value. Enabling the Autopilot Controls on a Garmin Watch You can control the Garmin autopilot with a compatible Garmin watch. Go to garmin.com for a list of compatible Garmin watches. NOTE: Smart notifications are not available on your watch when the autopilot remote control is enabled. 1 Select Communications > Wireless Devices > Connect IQ Apps > Autopilot Control > Enable > New Connection. 2 Follow the on-screen instructions. Customizing the Autopilot Button Actions Before you can set the autopilot button actions, you must install and configure a compatible Garmin autopilot. You can select up to three autopilot actions for your Garmin watch to perform. NOTE: Available autopilot actions depend on the autopilot installed. 1 On the chartplotter, select Communications > Wireless Devices > Connect IQ Apps > Autopilot Control >

Button Actions. 2 Select a button. 3 Select an action. Controlling the Autopilot with a GRID 20 Remote Control Press the knob to change the mode. While in step steering mode, turn the knob to steer. Each turn of the knob produces a 1-degree step turn. While in autopilot response mode, turn the knob to adjust the Response setting. 41 While in rudder steering mode, hold the joystick to the right or left to steer. Reactor Autopilot Remote Control WARNING You are responsible for the safe and prudent operation of your vessel. The autopilot is a tool that enhances your capability to operate your boat. It does not relieve you of the responsibility of safely operating your boat. Avoid navigational hazards and never leave the helm unattended. You can wirelessly connect a Reactor autopilot remote control to the chartplotter to control the compatible Reactor autopilot system. For more information about using the remote, see the Reactor autopilot remote control instructions at garmin.com Pairing a Reactor Autopilot Remote Control With a Chartplotter 1 Select Settings > Communications > Wireless Devices >

Wireless Remotes > Autopilot Remote. 2 If necessary, select Enable. 3 Select New Connection. 4 On the remote control, select

> Pair with MFD. The chartplotter beeps and shows a confirmation message. 5 On the chartplotter, select Yes to complete the pairing process. Changing the Functions of the Reactor Autopilot Remote Control Action Keys You can change the patterns or actions assigned to the Reactor autopilot remote control action keys. 1 Select Settings > Communications > Wireless Devices >

Wireless Remotes > Autopilot Remote > Button Actions. 2 Select an action key to change. 3 Select a pattern or action to assign to the action key. Updating the Reactor Autopilot Remote Control Software You can update the Reactor autopilot remote control software using the chartplotter. 1 Insert a memory card into the card slot on the computer. 2 Go to buy.garmin.com/p/636376, and select Software. 3 Select Download. 4 Read and agree to the terms. 5 Select Download. 6 Choose a location, and select Save. 7 Double-click the downloaded file. 8 Select Next. 9 Select the drive associated with the memory card, and select Next > Finish. 10On the chartplotter, insert the memory card into the card slot. 11Select Settings > Communications > Wireless Devices >

Wireless Remotes > Autopilot Remote > Update Software. Yamaha Autopilot WARNING You can use the autopilot feature only at a station installed next to a helm, throttle, and helm control device. You are responsible for the safe and prudent operation of your vessel. The autopilot is a tool that enhances your capability to operate your boat. It does not relieve you of the responsibility of safely operating your boat. Avoid navigational hazards and never leave the helm unattended. Always be prepared to promptly regain manual control of your boat. Learn to operate the autopilot on calm and hazard-free open water. Use caution when operating the autopilot near hazards in the water, such as docks, pilings, and other boats. The autopilot system continuously adjusts the steering of your boat to maintain a constant heading (heading hold). When the chartplotter is connected to a compatible Yamaha autopilot system, you can view the autopilot information using the Yamaha autopilot screen and overlay bar. For information about compatible Yamaha autopilot systems, contact your Yamaha dealer. Yamaha Autopilot Screen Actual heading Intended heading (heading the autopilot is steering toward) Yamaha Autopilot Settings From a Yamaha engine screen, select Menu > Autopilot Setting. Pattern Set: Allows you to select an autopilot pattern. Direction: Sets a port or starboard direction for the pattern. Spacing: Sets the spacing for the pattern. Length: Sets the length of the pattern. Amplitude: Sets the angle for the zigzag pattern. Initial Radius: Sets the radius of the spiral pattern. Final Track Point Mode: Sets the mode for the autopilot when it reaches the end of a route. The FishPoint option maintains the position, but does not maintain the heading. The DriftPoint option allows the boat to drift with the wind or current while maintaining the selected heading, but does not maintain the position. The StayPoint option maintains the position and the heading. The Deceleration option stops the motor, but does not maintain the position or heading. The No Deceleration option does not stop the motor. Course Hold Offset: Sets a distance to navigate parallel to a route. Yamaha Autopilot Overlay Bar Autopilot mode Actual heading Intended heading (heading the autopilot is steering toward) Opens the full autopilot screen and menu 42 Autopilot Force Trolling Motor Control WARNING Do not run the motor when the propeller is out of the water. Contact with the rotating propeller may result in severe injury. Do not use the motor in areas where you or other people in the water may come into contact with the rotating propeller. Always disconnect the motor from the battery before cleaning or servicing the propeller to avoid injury. You are responsible for the safe and prudent operation of your vessel. The autopilot is a tool that enhances your capability to operate your boat. It does not relieve you of the responsibility of safely operating your boat. Avoid navigational hazards and never leave the helm unattended. Learn to operate the autopilot on calm and hazard-free open water. Use caution when operating the autopilot near hazards in the water, such as docks, pilings, and other boats. CAUTION When using the autopilot features, be prepared for sudden stops, acceleration, and turns. When stowing or deploying the motor, be aware of the risk of entrapment or pinching from moving parts, which can result in injury. When stowing or deploying the motor, be aware of slick surfaces around the motor. Slipping when stowing or deploying the motor may result in injury. You can connect the Force trolling motor to the chartplotter to view and control the motor using the chartplotter. Connecting to a Trolling Motor You can connect the chartplotter wirelessly to a compatible Garmin Force trolling motor on your boat to control the trolling motor from the chartplotter. 1 Turn on the chartplotter and the trolling motor. 2 Enable the WiFi network on the chartplotter (Setting Up the WiFi Wireless Network, page 8). 3 If multiple chartplotters are connected on the Garmin Marine Network, make sure this chartplotter is the host of the WiFi network (Changing the WiFi Host, page 8). 4 On the chartplotter, select Settings > Communications >

Wireless Devices > Garmin Trolling Motor. 5 On the trolling motor display panel, press three times to enter pairing mode. 4 Select Trolling Motor Bar. Repeat these steps to add the trolling motor controls to all of the screens from which you would like to control the trolling motor. Trolling Motor Control Bar The trolling motor control bar allows you to control a Force trolling motor and see the status of the motor. Select an item to engage it. The button illuminates when selected. Select the item again to disengage it. Trolling motor battery status. Turns the propeller on and off. Reduces the speed. Speed indicator. Increases the speed. Enables the cruise control at the current speed over ground

(SOG). Engages the propellor at full speed. Trolling motor status. Enables anchor lock, which uses the trolling motor to hold your position. Steers the trolling motor. When in anchor lock, jogs the anchor lock position forward, backward, left, or right. Enables heading hold (set and maintain the current heading). When the trolling motor is in heading hold, an autopilot bar appears in the trolling motor bar. Opens the trolling motor settings. Trolling Motor Settings From the trolling motor bar, select Calibrate: Calibrates the trolling motor compass (Calibrating the

. Trolling Motor Compass, page 44) and sets the trolling motor bow offset (Setting the Bow Offset, page 44). Anchor Gain: Sets the response of the trolling motor when in anchor lock mode. If you need the trolling motor to be more responsive and move quicker, increase the value. If the motor is moving too much, decrease the value. Navigation Gain: Sets the response of the trolling motor when navigating. If you need the trolling motor to be more responsive and move quicker, increase the value. If the motor is moving too much, decrease the value. Heading Hold Mode: Sets the heading hold mode. The Vessel on the trolling motor display panel is solid blue as it searches for a connection to the chartplotter, and turns green when the connection is successful. Align option attempts to keep the boat pointing in the same direction. The Go To option attempts to navigate a straight line in the requested direction. After the chartplotter and trolling motor connect successfully, enable the trolling motor overlay bar to control the motor (Adding the Trolling Motor Controls to Screens, page 43). Adding the Trolling Motor Controls to Screens After you have connected the chartplotter to the Force trolling motor, you must add the trolling motor control bar to screens to control the trolling motor. 1 Open a screen from which you would like to control the trolling motor. 2 Select an option:

From a combination page or SmartMode layout, select Menu > Edit > Overlays. From a full screen, select Menu > Edit Overlays. Arrival Mode: Sets the behavior of the trolling motor when you reach the end of a route. With the Anchor Lock setting, the trolling motor holds the position using the anchor lock feature when the boat reaches the end of the route. With the Manual setting, the propeller turns off when the boat reaches the end of the route. When using the Manual setting for the Arrival Mode option, you must be ready to take control of the boat. CAUTION Auto Power On: Turns on the trolling motor when you apply power to the system. Prop. Stow Side: Sets which side of the trolling motor the propellor rotates to when stowing the trolling motor. This is helpful when you store other items near the stowed propellor. 3 Select Top Bar or Bottom Bar. Force Trolling Motor Control 43 Shortcut Keys: Enables the shortcut keys on the trolling motor remote control to work with this particular chartplotter. The keys work with only one chartplotter at a time. Restore Defaults: Resets the trolling motor settings to the factory default values. Assigning a Shortcut to the Trolling Motor Remote Control Shortcut Keys You can quickly open commonly used screens by assigning a shortcut key on the trolling motor remote control. You can create a shortcut to screens, such as sonar screens and charts. NOTE: If you have more than one chartplotter on the network, you can assign shortcut keys to one chartplotter only. 1 Open a screen. 2 Hold a shortcut key. TIP: The shortcut is also saved to the Favorites category with the shortcut key number. Calibrating the Trolling Motor Compass You must calibrate the compass in the trolling motor before you can use the autopilot features. 1 Drive the boat to an open area of calm water. 2 From the trolling motor bar, select

> Calibrate >

Compass Cal.. 3 Follow the on-screen instructions. Setting the Bow Offset Based on the installation angle, the trolling motor may not align with the center line of your boat. For the best results, you should set the bow offset. 1 Adjust the angle of the trolling motor so it aligns with the center line of your boat

, pointing straight forward. 2 From the trolling motor bar, select

> Calibrate > Bow Offset. Digital Selective Calling Networked Chartplotter and VHF Radio Functionality If you have a NMEA 0183 VHF radio or a NMEA 2000 VHF radio connected to your chartplotter, these features are enabled. The chartplotter can transfer your GPS position to your radio. If your radio is capable, GPS position information is transmitted with DSC calls. The chartplotter can receive digital selective calling (DSC) distress and position information from the radio. The chartplotter can track the positions of vessels sending position reports. If you have a Garmin NMEA 2000 VHF radio connected to your chartplotter, these features are also enabled. The chartplotter allows you to quickly set up and send individual routine call details to your Garmin VHF radio. When you initiate a man-overboard distress call from your radio, the chartplotter shows the man-overboard screen and prompts you to navigate to the man-overboard point. When you initiate a man-overboard distress call from your chartplotter, the radio shows the Distress Call page to initiate a man-overboard distress call. Turning On DSC Select Settings > Other Vessels > DSC. DSC List The DSC list is a log of the most recent DSC calls and other DSC contacts you have entered. The DSC list can contain up to 100 entries. The DSC list shows the most recent call from a boat. If a second call is received from the same boat, it replaces the first call in the call list. Viewing the DSC List Before you can view the DSC list, the chartplotter must be connected to a VHF radio that supports DSC. Select Info > DSC List. Adding a DSC Contact You can add a vessel to your DSC list. You can make calls to a DSC contact from the chartplotter. 1 Select Info > DSC List > Add Contact. 2 Enter the Maritime Mobile Service Identity (MMSI) of the vessel. 3 Enter the name of the vessel. Incoming Distress Calls If your compatible chartplotter and VHF radio are connected using NMEA 0183 or NMEA 2000, your chartplotter alerts you when your VHF radio receives a DSC distress call. If position information was sent with the distress call, that information is also available and recorded with the call. designates a distress call in the DSC list and marks the position of the vessel on the Navigation chart at the time of the DSC distress call. Navigating to a Vessel in Distress designates a distress call in the DSC list and marks the position of a vessel on the Navigation chart at the time of the DSC distress call. 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Navigate To. 4 Select Go To or Route To. Man-Overboard Distress Calls Initiated from a VHF Radio When the chartplotter is connected to a compatible VHF radio with NMEA 2000, and you initiate a man-overboard DSC distress call from the radio, the chartplotter shows the man-

overboard screen and prompts you to navigate to the man-

overboard point. If you have a compatible autopilot system connected to the network, the chartplotter prompts you to start a Williamsons turn to the man-overboard point. If you cancel the man-overboard distress call on the radio, the chartplotter screen prompting you to activate navigation to the man-overboard location disappears. 44 Digital Selective Calling Man-Overboard and SOS Distress Calls Initiated from the Chartplotter When your chartplotter is connected to a Garmin NMEA 2000 compatible radio and you mark an SOS or man-overboard location, the radio shows the Distress Call page so you can quickly initiate a distress call. For information on placing distress calls from your radio, see the VHF radio owners manual. For information about marking an MOB or SOS location, see Marking an SOS Location, page 18. Position Tracking When you connect the chartplotter to a VHF radio using NMEA 0183, you can track vessels that send position reports. This feature is also available with NMEA 2000, when the vessel sends the correct PGN data (PGN 129808; DSC Call Information). Every position report call received is logged in the DSC list

(DSC List, page 44). Viewing a Position Report 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review. 4 Select an option:

To view the position report details, select To view to a chart marking the location, select

. Navigating to a Tracked Vessel 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Navigate To. 4 Select Go To or Route To. Creating a Waypoint at the Position of a Tracked Vessel 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Create Waypoint. Editing Information in a Position Report 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Edit. To enter the name of the vessel, select Name. To select a new symbol, select Symbol, if available. To enter a comment, select Comment. To show a trail line for the vessel if your radio is tracking the position of the vessel, select Trail. To select a color for the trail line, select Trail Line. Deleting a Position-Report Call 1 Select Info > DSC List. 2 Select a position-report call. 3 Select Review > Clear Report. Viewing Vessel Trails on the Chart You can view trails for all tracked vessels on some chart views. By default, a black line indicates the path of the vessel, a black dot indicates each previously reported position of a tracked vessel, and a blue flag indicates the last reported position of the vessel. 1 From a chart or 3D chart view, select Menu > Layers >

Other Vessels > DSC > DSC Trails. 2 Select the number of hours to show tracked vessels on the chart. Gauges and Graphs For example, if you select 4 Hours, all trail points that are less than four hours old appear for all tracked vessels. Individual Routine Calls When you connect the chartplotter to a Garmin VHF radio, you can use the chartplotter interface to set up an individual routine call. When setting up an individual routine call from your chartplotter, you can select the DSC channel on which you want to communicate. The radio transmits this request with your call. Selecting a DSC Channel NOTE: The selection of a DSC channel is limited to those channels that are available in all frequency bands. The default channel is 72. If you select a different channel, the chartplotter uses that channel for subsequent calls until you call using another channel. 1 Select Info > DSC List. 2 Select a vessel or a station to call. 3 Select Review > Call with Radio > Channel. 4 Select an available channel. Making an Individual Routine Call NOTE: When initiating a call from the chartplotter, if the radio does not have an MMSI number programmed, the radio will not receive call information. 1 Select Info > DSC List. 2 Select a vessel or a station to call. 3 Select Review > Call with Radio. 4 If necessary, select Channel, and select a new channel. 5 Select Send. The chartplotter sends information about the call to the radio. 6 On your Garmin VHF radio, complete the call. Making an Individual Routine Call to an AIS Target 1 From a chart or 3D chart view, select an AIS target. 2 Select AIS Vessel > Call with Radio. 3 If necessary, select Channel, and select a new channel. 4 Select Send. The chartplotter sends information about the call to the radio. 5 On your Garmin VHF radio, complete the call. Gauges and Graphs The gauges and graphs provide various information about the engine and environment. To view the information, a compatible transducer or sensor must be connected to the network. Viewing the Gauges 1 Select A/V, Gauges, Controls. 2 Select a gauge. 3 Select or to view a different gauge page. Changing the Data Shown in a Gauge 1 From a gauges screen, hold a gauge. 45 2 Select Replace Data. 3 Select a data type. 4 Select the data to display. Customizing the Gauges You can change the layout of the gauge pages, how the gauges pages are displayed, and the data in each gauge. 1 Open a gauge page. 2 Select Menu > Edit Gauge Pages. 3 Select an option:

To change the data shown in a gauge, select the gauge. To change the layout of the gauges on the page, select To add a page to this set of gauge pages, select Add Change Layout. Page. To change the order of this page in the set of gauge pages, select Move Page Left or Move Page Right. To restore this page to the original view, select Restore Default View. Customizing Engine Gauge and Fuel Gauge Limits You can configure the upper and lower limits and the range of desired standard operation of a gauge. NOTE: Not all options are available for all gauges. 1 From an applicable gauges screen, select Menu >

Installation > Set Gauge Limits. 2 Select a gauge to customize. 3 Select an option:

To set the minimum value of the standard operating range, select Rated Min.. To set the maximum value of the standard operating range, select Rated Max.. To set the lower limit of the gauge lower than the rated minimum, select Scale Min.. To set the upper limit of the gauge higher than the rated maximum, select Scale Max.. 4 Select the limit value. 5 Repeat steps 4 and 5 to set additional gauge limits. Selecting the Number of Engines Shown in Gauges You can show information for up to four engines. 1 From the engine gauges screen, select Menu > Installation

> Engine Selection > Num. Engines. 2 Select an option:

Customizing the Engines Shown in Gauges Before you can customize how the engines are shown in the gauges, you must manually select the number of engines

(Selecting the Number of Engines Shown in Gauges, page 46). 1 From the engine gauges screen, select Menu > Installation

> Engine Selection > Num. Engines. 2 Select First Engine. 3 Select the engine to display in the first gauge. 4 Repeat for the remaining engine bars. Enabling Status Alarms for Engine Gauges You can enable the chartplotter to display engine status alarms. From the engine gauges screen, select Menu > Installation

> Status Alarms > On. When an engine alarms is triggered, a gauge status alarm message appears and the gauge may become red depending on the type of alarm. Enabling Some Engine Gauge Status Alarms 1 From the engine gauges screen, select Menu > Installation

> Status Alarms > Custom. 2 Select one or more engine gauge alarms to turn on or off. Yamaha Engine Gauges Select A/V, Gauges, Controls > YAMAHA to view the Yamaha engine gauges. This screen varies based on the engine network and throttle controller. Data fields Hold to replace the data. Current time Hold to view trip data. Press to set the joystick button Set Point functions (Helm Master). Tank level information Hold a tank to view detailed tank level sensor information. GPS signal strength Select to set the Fish Point high RPM limit (Helm Master). Select to set the trolling speed (Command Link Plus). Data fields Hold to replace the data. Shift position Tachometer and trim angle Hold to change the background. Engine information Hold to replace the data and change the gauge appearance. Engine Condition Icons Orange icons indicate engine conditions. Yamaha security system is on. Engines are under synchronization control. Engines are warming up. Consult your Yamaha dealer if the problem cannot be located and corrected. NOTICE Low cooling water pressure. Low oil pressure. Stop the engine. Check the engine oil level, and add more oil if necessary. Do not continue to run the engine if this indicator is on. Serious engine damage will occur. NOTICE Select the number of engines. Select Auto Configure to automatically detect the number of engines. Engine Alert Icons Red icons indicate engine abnormalities. 46 Gauges and Graphs Engine overheating. Stop the engine immediately. Check the cooling water inlet, and clear it if it is blocked. Trim Assist: Turns the trim assist feature on or off. Available on the Helm Master system equipped with a digital engine control (DEC) system. Do not continue to run the engine if this indicator is on. Serious engine damage will occur. NOTICE Low battery voltage. Check the battery and battery connections, and tighten all loose battery connections. Return to port soon if tightening the battery connections does not increase the battery voltage. Consult your Yamaha dealer immediately. NOTE: Do NOT stop the engine when this alert is on. If you do, you may not be able to restart the engine. Water in the fuel. Water has collected in the fuel filter (fuel separator). Stop the engine immediately and consult the engine manual to drain the water from the fuel filter. NOTE: Gasoline mixed with water might cause damage to the engine. Check engine/maintenance alert. Consult your Yamaha dealer immediately. The check engine alert also appears when more than 100 hours have elapsed since the previous maintenance. Engine alert notification. (Helm Master) Engine emission issue. Setting Up the Gauges Configuring the Number of Engines 1 From a gauges screen, select Menu > Num. Engines. 2 Select the number of engines. Configuring the Tank Level Sensors 1 From a gauges screen, select Menu > Tank Preset. 2 Select a tank level sensor to configure. 3 Select Name, enter a name, and select Done. 4 Select Type, and select the type of sensor. 5 Select Style, and select the style of sensor. 6 Select Tank Capacity, enter the capacity of the tank, and select Done. 7 Select Calibration, and follow the on-screen instructions to calibrate the tank levels. If you do not calibrate the tank levels, the system uses default settings for the tank levels. Changing the Data Shown 1 From a data screen, hold a customizable item. 2 Select a data type. 3 Select the data to display. Yamaha Engine Data Settings NOTICE Be sure the settings are set correctly. If not, the engine screen will not display the correct information. From a Yamaha engine screen, select Menu. Trip: Displays information about the trip, such as distance and hours, and allows you to reset these values. Maintenance Reminder: Displays maintenance information, enables you to set the maintenance intervals, and allows you to reset the time elapsed since the previous maintenance. Tank Preset: Sets the tank name, fluid type, sensor style, and tank capacity, and calibrates the sensor. Steer Friction: Sets the friction on the steering wheel. The friction adjusts automatically according to the engine speed. Available on the Helm Master system equipped with a digital engine control (DEC) system. Lock to Lock: Sets the number of times the steering wheel can be turned between locks, fully to port and fully to starboard. Speed Control: Sets the speed source to GPS or RPM. Using GPS as the Speed Source is available only with the Helm Master EX system equipped with an autopilot or joystick. GPS is not available on the Helm Master system. Autopilot Setting: Configures the Yamaha autopilot settings. Available on the Helm Master EX system equipped with an autopilot. For Garmin autopilot information, see (Autopilot, page 39). Joystick and Set Point: Sets the joystick thrust, trim angle and preset, fine tuning distance, and fish point settings. Available on the Helm Master system and the Helm Master EX system equipped with a joystick. Trim Assist Preset: Sets up the trim assist presets. Available on the Helm Master system equipped with a digital engine control (DEC) system. Fuel Flow Offset: Sets the offset for the fuel flow data. Off Timer: Turns off the system one hour after the engine is turned off. Battery Management: Configures the battery management system, such as setting the type and capacity of the batteries. Also displays the battery status. Available on Helm Master EX systems equipped with Battery Management System (BMS). Calibration: Calibrates various features, such as the Trim Zero Set and compass. Reset: Resets the engine and gateway data. Setting the Fuel Alarm Before you can set a fuel level alarm, a compatible fuel flow sensor must be connected to the chartplotter. You can set an alarm to sound when the total amount of remaining onboard fuel reaches the level you specify. 1 Select Settings > Alarms > Fuel > Set Total Fuel Onboard 2 Enter the remaining amount of fuel that triggers the alarm,

> On. and select Done. Setting the Fuel Capacity of the Vessel 1 Select Settings > My Vessel > Fuel Capacity. 2 Enter the combined total capacity of the fuel tanks. Synchronizing the Fuel Data with the Actual Vessel Fuel You can synchronize the fuel levels in the chartplotter with the actual fuel in the vessel when you add fuel to your vessel. 1 Select A/V, Gauges, Controls > Engines > Menu. 2 Select an option:

After you have filled up all the fuel tanks on the vessel, select Fill Up All Tanks. The fuel level is reset to maximum capacity. After you have added less than a full tank of fuel, select Add Fuel to Boat, and enter the amount added. To specify the total fuel in the vessel tanks, select Set Total Fuel Onboard, and enter the total amount of fuel in the tanks. Gauges and Graphs 47 Viewing the Wind Gauges Before you can view wind information, you must have a wind sensor connected to the chartplotter. To set the odometer reading to zero, select Reset Odometer. To set all the readings to zero, select Reset All. To calculate the vessel speed based on data from the 6 Repeat steps 2 through 5 for each device. Select A/V, Gauges, Controls > Wind. Configuring the Sailing Wind Gauge You can configure the sailing wind gauge to show true or apparent wind speed and angle. 1 From the wind gauge, select Menu > Sailing Wind Gauge. 2 Select an option:

To show true or apparent wind angle, select Needle, and To show true or apparent wind speed, select Wind Speed, select an option. and select an option. Configuring the Speed Source You can specify whether the vessel speed data displayed on the gauge and used for wind calculations is based on water speed or GPS speed. 1 From the wind gauge, select Menu > Compass Gauge >

Speed Display. 2 Select an option:

water-speed sensor, select Water Speed. To calculate the vessel speed based on GPS data, select GPS Speed. Configuring the Heading Source of the Wind Gauge You can specify the source of the heading displayed on the wind gauge. Magnetic heading is the heading data received from a heading sensor, and GPS heading is calculated by your chartplotter GPS (course over ground). 1 From the wind gauge, select Menu > Compass Gauge >

Heading Source. 2 Select GPS or Magnetic. NOTE: When moving at low speeds or when stationary, the magnetic compass source is more accurate than the GPS source. Customizing the Close-Hauled Wind Gauge You can specify the range of the close-hauled wind gauge for both the upwind scale and the downwind scale. 1 From the wind gauge, select Menu > Compass Gauge >

Gauge Type > Close Hauled Gauge. 2 Select an option:

To set the maximum and minimum values that appear when the upwind close-hauled wind gauge appears, select Change Upwind Scale, and set the angles. To set the maximum and minimum values that appear when the downwind close-hauled wind gauge appears, select Change Downwind Scale, and set the angles. To view true or apparent wind, select Wind, and select an option. Viewing Trip Gauges Trip gauges show information for odometer, speed, time, and fuel for your present trip. Battery Management You can view the battery and other power sources, and the devices that use those sources. Batteries are listed along the top of the screen. Other sources of power, such as solar, alternator, converter, and wind generator, are listed along the left side. The items along the right side of the screen are devices that use the batteries and other power sources. Setting Up the Battery Management Page 1 Select A/V, Gauges, Controls > Battery Management >

Menu > Edit Devices. 2 Select an item. 3 Select Device, and select an item from the list. 4 If necessary, select Name, enter a name for this device, and 5 If necessary, select Change Icon, select a new symbol, and select Done. select Done. Viewing Graphs Before you can view graphs of various environmental changes, such as temperature, depth, and wind, you must have an appropriate transducer or sensor connected to the network. Select Info > Trip & Graphs > Graphs. Setting the Graph Range and Time Scales You can indicate the amount of time and the range of depth that appear in the depth and water temperature graphs. 1 From a graph, select Graph Setup. 2 Select an option:

To set a time-elapsed scale, select Duration. The default setting is 10 minutes. Increasing the time-elapsed scale allows you to view variations over a longer period of time. Decreasing the time-elapsed scale allows you to view more detail over a shorter period of time. To set the graph scale, select Scale. Increasing the scale allows you to view more variation in readings. Decreasing the scale allows you to view more detail in the variation. inReach Messages WARNING Do not read or reply to notifications while operating the vessel. Failure to pay attention to the conditions on the water can result in vessel damage, personal injury, or death. You can connect an inReach Mini device to the chartplotter to view, reply to, and send preset messages from the chartplotter. NOTE: The inReach Mini device must be connected to the chartplotter and receiving satellite signals to send and receive messages using the chartplotter. To open the InReach page, select A/V, Gauges, Controls >

InReach. Connecting an inReach Device to the Chartplotter You can connect a compatible inReach device to the chartplotter to manage messages. 1 Bring the inReach device within 3 m (10 ft.) of the inReach Messages Select Info > Trip & Graphs > Trip. Resetting Trip Gauges 1 Select Info > Trip & Graphs > Trip. 2 Select an option:

Reset Trip. Maximum Speed. 48 To set all the readings for the present trip to zero, select To set the maximum speed reading to zero, select Reset chartplotter. 2 From the main menu of the inReach device, select Setup >

ANT+ > Status > On. 3 On the chartplotter, select A/V, Gauges, Controls >

InReach > Start Pairing. The chartplotter begins searching for and connecting to the inReach device. This can take up to 60 seconds. 4 If necessary, compare the code on the inReach device to the chartplotter, and select OK if they match. The inReach and chartplotter connect automatically when they are within range. Dometic Optimus Features When connected to a compatible Optimus system, the chartplotter allows you to access and control the system. You can enable the Optimus overlay to control the Optimus system

(Activating the Optimus Overlay Bar, page 49). When necessary, the Optimus system provides messages with information, instructions, and alerts about faults and hazards. A no swimming icon certain Optimus modes are active. In these modes, propeller control is automatic and could injure someone in the water. indicates that you should not swim when Receiving inReach Messages When your inReach device receives a message, a pop-up notification appears briefly on the GPSMAP screen. To review the full message, select Review. To dismiss the pop-up notification, select OK or wait for the notification to close automatically. Sending an inReach Preset Message Preset messages are messages that you created at explore.garmin.com. Preset messages have predefined text and recipients. 1 From the InReach page, select Messages > Send inReach Preset. 2 Select a preset message. 3 Select Send. Replying to an inReach Message You can reply to an inReach message with a pre-written message. 1 From the InReach page, select Messages. A list of sent and received messages appears. 2 Select a received message. 3 Select Reply. 4 Select a message. 5 Select Send. Digital Switching Your chartplotter can be used to monitor and control circuits when a compatible system is connected. For example, you can control the interior lights and navigation lights on the vessel. You can also monitor live well circuits. To access the digital switching controls, select A/V, Gauges, Controls > Switching. For more information about purchasing and configuring a digital switching system, contact your Garmin dealer. Adding and Editing a Digital Switching Page You can add and customize digital switching pages to the chartplotter. 1 Select A/V, Gauges, Controls > Switching > Menu >

Setup. 2 Select Add Page or Edit Page. 3 Set up the page as needed:

To enter a name for the page, select Name. To set up the switches, select Edit Switches. To add an image of the boat, select Add BoatView Image. NOTE: You can load an image of your vessel into the device to use for the image, or use a default image. You can also adjust the view and placement of the image. Activating the Optimus Overlay Bar 1 From a chart, select Menu > Edit Overlays. 2 Select Top Bar or Bottom Bar. 3 Select Optimus Bar. Optimus Overlay Bar Overview To use the overlay bar, you must connect your Optimus system to your chartplotter and add the overlay bar to the necessary screens (Activating the Optimus Overlay Bar, page 49). You must press a mode button on the overlay bar to engage or disengage the mode. When the mode is engaged, the button is illuminated. The overlay bar configuration and buttons vary, based on systems, modes, and equipment. Refer to your Optimus documentation for more information. Optimus Overlay Symbols Control mode Optimus control buttons Rudder Standby button Autopilot heading hold Autopilot track mode Autopilot route mode SeaStation position hold SeaStation heading hold Optimus Limp Home Mode WARNING In the event of a steering failure, Optimus Limp Home mode becomes available. Limp Home mode is a system override that may severely limit your boat's control. It should only be used in an emergency if you are unable to call for assistance. Proceed with extreme caution. Read the Optimus owner's manual and always wear a personal flotation device (PFD). You are responsible for the safe and prudent operation of your vessel. Use of Limp Home mode does not relieve you of the responsibility of safely operating your boat. Avoid navigational hazards and never leave the motor controls unattended. When available, the Limp Home button appears on the Optimus overlay bar. Refer to the Optimus owner's manual before using Limp Home mode. To engage Limp Home mode from any screen, select Info >

Warning Manager > Steering Limp Home. Digital Switching 49 Tide, Current, and Celestial Information 3 Select Nearby Stations. 4 Select a station. Tide Station Information WARNING Tide and current information is for information purposes only. It is your responsibility to heed all posted water-related guidance, to remain aware of your surroundings, and to use safe judgment in, on, and around the water at all times. Failure to heed this warning could result in property damage, serious personal injury, or death. You can view information about a tide station for a specific date and time, including the tide height, and when the next high and low tides will occur. By default, the chartplotter shows tide information for the most recently viewed tide station, present date, and past hour. Select Info > Tides & Currents > Tides. Current Station Information WARNING Tide and current information is for information purposes only. It is your responsibility to heed all posted water-related guidance, to remain aware of your surroundings, and to use safe judgment in, on, and around the water at all times. Failure to heed this warning could result in property damage, serious personal injury, or death. NOTE: Current station information is available with certain detailed maps. You can view information about a current station for a specific date and time, including the current speed and level of the current. By default, the chartplotter shows current information for the most recently viewed current station and for the present date and time. Select Info > Tides & Currents > Currents. Celestial Information You can view information about sunrise, sunset, moonrise, moonset, moon phase, and the approximate sky view location of the sun and moon. The center of the screen represents the sky overhead, and the outermost rings represent the horizon. By default, the chartplotter shows celestial information for the present date and time. Select Info > Tides & Currents > Celestial. Viewing Tide Station, Current Station, or Celestial Information for a Different Date 1 Select Info > Tides & Currents. 2 Select Tides, Currents, or Celestial. 3 Select an option:

To view information for a different date, select Change Date > Manual, and enter a date. To view information for today, select Change Date >

Current. If available, to view information for the day after the date shown, select Next Day. If available, to view information for the day before the date shown, select Previous Day. Viewing Information for a Different Tide or Current Station 1 Select Info > Tides & Currents. 2 Select Tides or Currents. Viewing Almanac Information from the Navigation Chart 1 From a chart or 3D chart view, select a location. 2 Select Information. 3 Select Tides, Currents, or Celestial. Warning Manager During an active warning, an indicator appears on the Info button on the menu bar. The Warning Manager displays a color-

coded alarm icon and prioritizes alarm messages by severity. Color Severity Red Hazards that require immediate action to avoid severe personal injury or death Yellow Hazards or unsafe practices which could result in minor personal injury or product or property damage Viewing Messages 1 Select Info > Warning Manager. 2 Select a message. 3 Select Review. Sorting and Filtering Messages 1 Select Info > Warning Manager > Sort/Filter. 2 Select an option to sort or filter the message list. Saving Messages to a Memory Card 1 Insert a memory card into the card slot. 2 Select Info > Warning Manager > Save to Card. Clearing all of the Messages Select Info > Warning Manager > Clear Warning Manager. Media Player NOTE: The media player feature is not compatible with all chartplotter models. NOTE: Not all features are available on all connected media players. If you have a compatible stereo connected to the NMEA 2000 network or Garmin Marine Network, you can control the stereo using the chartplotter. The chartplotter should automatically detect the media player when it is first connected. You can play media from sources connected to the media player and sources connected to the network. Opening the Media Player Before you can open the media player, you must connect a compatible device to the chartplotter. Select A/V, Gauges, Controls > Media. Media Player Icons NOTE: Not all devices have these icons. Icon Description Saves or deletes a channel as a preset Repeats all songs Repeats one song Shuffles Searches for stations or skips songs 50 Tide, Current, and Celestial Information Selecting the Media Device and Source You can select the media source connected to the stereo. When you have multiple stereo or media devices connected on a network, you can select the device from which you want to play music. NOTE: You can play media only from sources that are connected to the stereo. NOTE: Not all features are available on all media devices and sources. 1 From the media screen, select Devices, and select the stereo. 2 From the media screen, select Source, and select the media source. NOTE: The Devices button only appears when more than one media device is connected to the network. NOTE: The Source button only appears for devices that support multiple media sources. Playing Music Browsing for Music 1 From the media screen, select Browse or Menu > Browse. 2 Select Select or select an option. Enabling Alphabetical Search You can enable the alphabetical search feature to find a song or album in a large list. From the media screen, select Menu > Installation > Alpha Search. Setting a Song to Repeat 1 While playing a song, select Menu > Repeat. 2 If necessary, select Single. Setting All Songs to Repeat From the media screen, select Menu > Repeat > All. Setting Songs to Shuffle 1 From the media screen, select Menu > Shuffle. 2 If necessary, select an option. Joining the Fusion PartyBus Network You can play music from other compatible stereos connected to the Fusion PartyBus network. One Fusion PartyBus stereo must be connected to the chartplotter using the NMEA 2000 network. NOTE: A Fusion PartyBus zone stereo, such as the Apollo SRX400 zone stereo, cannot stream sources to other Fusion PartyBus devices on the network. Because of this, zone stereos do not appear as available sources in the chartplotter. 1 From the media screen, select Source. NOTE: After few moments, the compatible Fusion PartyBus stereos appear as sources. 2 Select the Fusion PartyBus stereo. 3 If necessary, select Source, and select a different source connected to the Fusion PartyBus stereo. To leave the Fusion PartyBus network, you can select Source >

Leave PartyBus. Adjusting the Volume Muting the Media Volume 1 From the media screen, select 2 If necessary, select Select. Enabling and Disabling Zones If you have wired your vessel's speakers into zones, you can enable needed zones and disable unused zones. 1 From the media screen, select Menu > Audio Levels >

Enable/Disable Zones. 2 Select a zone. VHF Radio NOTE: These features are available on some stereos with a VHF receiver. Scanning VHF Channels Before you can scan VHF channels, you must set the source to VHF. You can monitor VHF channels saved as presets for activity and automatically switch to an active channel. From the VHF media screen, select Scan. Adjusting the VHF Squelch NOTE: This feature is available on some stereos with a VHF receiver. 1 From the VHF source page, select Menu > Squelch. 2 Use the slider bar to adjust the VHF squelch. Radio To listen to AM or FM radio, you must have a suitable marine AM/FM antenna properly connected to the stereo and be within range of a broadcasting station. For instructions on connecting an AM/FM antenna, see the stereo installation instructions. To listen to SiriusXM radio, you must have the appropriate equipment and subscriptions (SiriusXM Satellite Radio, page 52). For instructions on connecting a SiriusXM Connect Vehicle Tuner, see the stereo installation instructions. To listen to DAB stations, you must have the appropriate equipment (DAB Playback, page 52). For instructions on connecting a DAB adapter and antenna, see the installation instructions provided with your adapter and antenna. Setting the Tuner Region 1 From the media screen, select Menu > Installation > Tuner Region. 2 Select an option. Changing the Radio Station 1 From the media screen, select an applicable source, such as FM. 2 Select or to tune to a station. Changing the Tuning Mode You can change how you select a station for some media types, such as FM or AM radio. NOTE: Not all tuning modes are available for all media sources. 1 From the media screen, select Menu > Tuning Mode. 2 Select an option. 3 If necessary, select Select. Presets You can save your favorite AM stations and FM stations as presets for easy access. You can save your favorite SiriusXM channels if the stereo is connected to an optional SiriusXM tuner and antenna. You can save your favorite DAB stations if the stereo is connected to an optional DAB module and antenna. Saving a Station as a Preset 1 From an applicable media screen, tune to the station to save as a preset. 2 Select Presets > Add Current Channel. Selecting a Preset 1 From an applicable media screen, select Presets. Media Player 51 2 Select a preset from the list. 3 Select Tune to Channel. Removing a Preset 1 From an applicable media screen, select Presets. 2 Select a preset from the list. 3 Select Remove Current Channel. DAB Playback When you connect a compatible Digital Audio Broadcasting

(DAB) module and antenna, such as the Fusion MS-DAB100A to a compatible stereo, you can tune in to and play DAB stations To use the DAB source, you must be in a region in which DAB is available, and select the tuner region (Setting the DAB Tuner Region, page 52). Setting the DAB Tuner Region You must select the region you are in to receive DAB stations properly. 1 From the media screen, select Menu > Installation > Tuner Region. 2 Select the region you are in. Scanning for DAB Stations Before you can scan for DAB stations, you must connect a compatible DAB module and antenna (not included) to the stereo. Because DAB signals are broadcast in select countries only, you must also set the tuner region to a location where DAB signals are broadcast. 1 Select the DAB source. 2 Select Scan to scan for available DAB stations. When scanning is complete, the first available station in the first ensemble found begins playing. NOTE: After the first scan is complete, you can select Scan again to re-scan for DAB stations. When the re-scan is complete, the system starts playing the first station in the ensemble you were listening to when you started the re-scan. Changing DAB Stations 1 Select the DAB source. 2 If necessary, select Scan to scan for local DAB stations. 3 Select to change the station. or When you reach the end of the current ensemble, the stereo automatically changes to the first available station in the next ensemble. TIP: You can hold to change the ensemble. or Selecting a DAB Station from a List 1 From the DAB media screen, select Browse > Stations. 2 Select a station from the list. Selecting a DAB Station from a Category 1 From the DAB media screen, select Browse > Categories. 2 Select a category from the list. 3 Select a station from the list. DAB Presets You can save your favorite DAB stations as presets for easy access. You can save up to 15 DAB-station presets. Saving a DAB Station as a Preset 1 From the DAB media screen, select the station to save as a preset. 2 Select Browse > Presets > Save Current. Selecting a DAB Preset from a List 1 From the DAB media screen, select Browse > Presets >

View Presets. 2 Select a preset from the list. Removing DAB Presets 1 From the DAB media screen, select Browse > Presets. 2 Select an option:

To remove one preset, select Remove Preset, and select the preset. To remove all presets, select Remove All Presets. SiriusXM Satellite Radio When you have a FUSION-Link capable stereo and SiriusXM Connect Tuner installed and connected to the chartplotter, you may have access to SiriusXM satellite radio, depending on your subscription. Locating a SiriusXM Radio ID Before you can activate your SiriusXM subscription, you must have the radio ID of your SiriusXM Connect Tuner. You can locate the SiriusXM Radio ID on the back of the SiriusXM Connect Tuner, on the back of its packaging, or by tuning your chartplotter to channel 0. 1 Select Media > Source > SiriusXM. 2 Tune to channel 0. The SiriusXM radio ID does not include the letters I, O, S, or F. Activating a SiriusXM Subscription 1 With the SiriusXM source selected, tune to channel 1. You should be able to hear the preview channel. If not, check the SiriusXM Connect Tuner and antenna installation and connections, and try again. 2 Tune to channel 0 to locate the Radio ID. 3 Contact SiriusXM listener care by phone at (866) 635-2349 or go to www.siriusxm.com/activatenow to subscribe in the United States. Contact SiriusXM by phone at (877) 438-9677 or go to www.siriusxm.ca/activatexm to subscribe in Canada. 4 Provide the Radio ID. The activation process usually takes 10 to 15 minutes, but can take up to an hour. For the SiriusXM Connect Tuner to receive the activation message, it must be turned on and receiving the SiriusXM signal. 5 If the service is not activated within the hour, go to http://care.siriusxm.com/refresh or contact SiriusXM Listener Care by phone at 1-866-635-2349. Customizing the Channel Guide SiriusXM radio channels are grouped in categories. You can select the categories of channels that appear in the channel guide. Select an option:

If the media device is a FUSION-Link capable stereo, select Media > Browse > Channel. If the media device is a GXM antenna, select Media >

Category. Saving a SiriusXM Channel to the Presets List You can save your favorite channels to the presets list. 1 Select Media. 2 Select the channel to save as a preset. 3 Select an option:

If the media device is a FUSION-Link capable stereo, select Browse > Presets. 52 Media Player If the media device is a GXM antenna, select Menu >

Presets > Add Current Channel. 2 Insert the USB flash drive into the USB port of the stereo. 3 On the chartplotter media screen, select Menu > Installation Parental Controls The parental control feature allows you to limit access to any SiriusXM channels, including those with mature content. When the parental control feature is enabled, you must enter a passcode to tune to the locked channels. You can also change the 4-digit passcode. Unlocking SiriusXM Parental Controls 1 From the media screen, select Browse > Parental > Unlock. 2 Enter your passcode. The default passcode is 0000. Setting Parental Controls on SiriusXM Radio Channels Before you can set parental controls, the parental controls must be unlocked. The parental control feature allows you to limit access to any SiriusXM channels, including those with mature content. When enabled, the parental control feature requires you to enter a passcode to tune to the locked channels. Select Browse > Parental > Lock/Unlock. A list of channels appears. A checkmark indicates a locked channel. NOTE: When you view the channels after setting parental controls, the display changes:

indicates a locked channel. indicates an unlocked channel. Clearing All Locked Channels on a SiriusXM Radio Before you can clear all locked channels, the parental controls must be unlocked. 1 From the media screen, select Browse > Parental > Clear All Locked. 2 Enter your passcode. Restoring Default Parental Control Settings Values This process deletes all the settings information you have entered. When you restore the parental control settings to their default values, the passcode value is reset to 0000. 1 From the media menu, select Installation > Factory Defaults. 2 Select Yes. Changing a Parental Passcode on a SiriusXM Radio Before you can change the passcode, the parental controls must be unlocked. 1 From the media screen, select Browse > Parental > Change PIN. 2 Enter your passcode and select Done. 3 Enter a new passcode. 4 Confirm the new passcode. Setting the Device Name 1 From the media screen, select Menu > Installation > Set Device Name. 2 Enter a device name. 3 Select Select or Done. Updating the Media Player Software You can update the software on compatible connected stereos and accessories. 1 Go to www.fusionentertainment.com/marine, and download the software update onto a USB flash drive. Software updates and instructions are available on your device product page.

> Update Software. 4 Select the item to update. SiriusXM Weather WARNING The weather information provided through this product is subject to service interruptions and may contain errors, inaccuracies, or outdated information, and consequently should not be relied upon exclusively. Always use common sense while navigating, and check alternate weather information sources prior to making safety-related decisions. You acknowledge and agree that you shall be solely responsible for use of the weather information and all decisions taken with respect to navigating in weather. Garmin will not be responsible for any consequences of using SiriusXM weather information. NOTE: SiriusXM data is not available in all regions. A Garmin SiriusXM satellite weather receiver and antenna receives satellite weather data and shows it on various Garmin devices, including the Navigation chart on a compatible chartplotter. The weather data for each feature comes from reputable weather data centers such as the National Weather Service and the Hydrometeorological Prediction Center. For more information, go to www.siriusxm.com/sxmmarine. SiriusXM Equipment and Subscription Requirements To use satellite weather, you must have a compatible satellite weather receiver. To use SiriusXM satellite radio, you must have a compatible satellite radio receiver. Go to www.garmin.com for more information. You must also have a valid subscription to receive satellite weather and radio. For more information, refer to the instructions for your satellite weather and radio equipment. Weather Data Broadcasts Weather data is broadcast at different intervals for each weather feature. For example, radar is broadcast at five-minute intervals. When the Garmin receiver is turned on, or when a different weather feature is selected, the receiver must receive new data before it can be shown. You might experience a delay before weather data or a different feature appears on the chart. NOTE: Any weather feature can change in appearance if the source that provides the information changes. Weather Warnings and Weather Bulletins When a marine weather warning, weather watch, weather advisory, weather bulletin, or other weather statement is issued, shading indicates the area to which the information applies. The aqua lines on the chart indicate the boundaries of marine forecasts, coastal forecasts, and offshore forecasts. Weather bulletins may consist of either weather watches or weather advisories. To view information about the warning or bulletin, select the shaded area. Color Cyan Blue Red Yellow Red Marine Weather Group Flash Flood Flood Marine Severe Storm Tornado SiriusXM Weather 53 Changing the Weather Chart 1 From a combination screen or SmartMode layout with a weather chart, select Menu > Weather Menu > Change Weather. 2 Select a weather chart. Viewing Precipitation Information Precipitation ranging from very light rain and snow, up to strong thunderstorms, is indicated in varying shades and colors. Precipitation is shown either independently or with other weather information. Select Charts > Precipitation. The time stamp in the upper-left corner of the screen indicates the elapsed time since the weather data provider last updated the information. icon on the weather Storm Cell and Lightning Information Storm cell are represented by the precipitation chart. They indicate both the present position of a storm and the projected path of that storm in the immediate future. Red cones appear with a storm cell icon, and the widest part of each cone points in the direction of the projected path of the storm cell. The red lines in each cone indicate where the storm will most likely be in the near future. Each line represents 15 minutes. Lightning strikes are represented by the icon. Lightning appears on the weather precipitation chart if strikes were detected within the last seven minutes. The ground-based lightning detection network detects cloud-to-ground lightning only. NOTE: This feature is not available on all devices and in all subscriptions. Hurricane Information The weather Precipitation chart can show the present position of a hurricane line stemming from a hurricane icon indicates the projected path of the hurricane. Darkened dots on the red line indicate the projected locations through which the hurricane will pass, as received from the weather data provider.

, a tropical storm, or a tropical depression. A red Forecast Information The Forecast chart shows city forecasts, marine forecasts, warnings, hurricane warnings, METARS, county warnings, weather fronts and pressure centers, surface pressure, and weather buoys. Viewing a Marine Forecast or an Offshore Forecast 1 Select Charts > Forecast. 2 Pan the chart to an offshore location. The Marine Forecast or Offshore Forecast options appear when forecast information is available. 3 Select Marine Forecast or Offshore Forecast. Viewing Forecast Information for Another Time Period 1 Select Charts > Forecast. 2 Select an option:

To view the weather forecast for the next 48 hours, in 12-

hour increments, select multiple times. To view the weather forecast for the previous 48 hours, in 12-hour increments, select multiple times. Weather Fronts and Pressure Centers Weather fronts appear as lines that indicate the leading edge of an air mass. Front Symbol Description Cold front Warm front Stationary front Occluded front Trough Pressure-center symbols often appear near weather fronts. Description Pressure-

Center Symbol Indicates a low-pressure center, which is a region of relatively lower pressure. Moving away from a low-

pressure center results in increased pressure. Winds flow counterclockwise around low-pressure centers in the northern hemisphere. Indicates a high-pressure center, which is a region of relatively higher pressure. Moving away from a high-

pressure center results in decreased pressure. Winds flow clockwise around high-pressure centers in the northern hemisphere. City Forecasts City forecasts appear as weather symbols. The forecast is viewed in 12-hour increments. Symbol Weather Fair (sunny, hot, clear) Partly cloudy Cloudy Rain (drizzle, sleet, showers) Thunderstorms Windy Foggy Smoke (dusty, hazy) Snow (snow showers, flurries, blizzard, blowing snow, sleet, freezing rain, freezing drizzle) Viewing Fish Mapping Data NOTE: This feature requires a GXM 54 antenna and a SiriusXM Fish Mapping service subscription. The Fish Mapping weather chart shows information that can help you locate fish species. 1 Select Charts > Fish Mapping. 2 If necessary, select Menu > Layers, and turn on and off information. Viewing Sea Conditions The Sea Conditions feature shows information about surface conditions, including winds, wave height, wave period, and wave direction. Select Charts > Sea Conditions. Surface Winds Surface wind vectors appear on the Sea Conditions chart using wind barbs that indicate the direction from which the wind is blowing. A wind barb is a circle with a tail. The line or flag attached to the tail of the wind barb indicates the wind speed. A short line represents 5 knots, a long line represents 10 knots, and triangle represents 50 knots. Wind Barb Wind Speed Calm 5 knots 10 knots 15 knots 54 SiriusXM Weather Wind Barb Wind Speed 20 knots 50 knots 65 knots Wave Height, Wave Period, and Wave Direction Wave heights for an area appear as variations in color. Different colors indicate different wave heights, as shown in the legend. The wave period indicates the time (in seconds) between successive waves. Wave period lines indicate areas that have the same wave period. Wave directions appear on the chart using red arrows. The direction of each arrow pointer indicates the direction in which a wave is moving. Viewing Forecast Sea Conditions Information for Another Time Period 1 Select Charts > Sea Conditions. 2 Select an option:

To view forecasted sea conditions for the next 36 hours, in 12-hour increments, select multiple times. To view the forecasted sea conditions for the previous 36 hours, in 12-hour increments, select multiple times. Viewing Sea Temperature Information The Sea Temperature weather chart shows the present water temperature and present surface pressure conditions. Select Charts > Sea Temperature. Surface Pressure and Water Temperature Data Surface-pressure information appears as pressure isobars and pressure centers. Isobars connect points of equal pressure. Pressure readings can help to determine weather and wind conditions. High-pressure areas are generally associated with fair weather. Low-pressure areas are generally associated with clouds and the chance of precipitation. Isobars packed closely together show a strong pressure gradient. Strong pressure gradients are associated with areas of stronger winds. Pressure units are shown in millibars (mb), inches of Mercury

(inHg), or hectopascals (hPa). Colored shading indicates the surface temperature of the water, as shown in the legend in the corner of the display. Changing the Sea Surface Temperature Color Range You can change the color range dynamically to view higher resolution sea surface temperature readings. 1 Select Charts > Sea Temperature > Menu > Sea Temperature. 2 Select an option:

To allow the chartplotter to adjust the temperature range automatically, select Auto Configure. The chartplotter automatically finds the lower and upper limits for the current screen, and updates the temperature-

color scale. Viewing Forecast Visibility Information for Another Time Period 1 Select Charts > Visibility. 2 Select an option:

To view the visibility forecast for the next 36 hours, in 12-

hour increments, select multiple times. To view the visibility forecast for the previous 36 hours, in 12-hour increments, select multiple times. Viewing Buoy Reports Report readings are taken from buoys and coastal observation stations. These readings are used to determine air temperature, dew point, water temperature, tide, wave height and period, wind direction and speed, visibility, and barometric pressure. 1 From a weather chart, select 2 Select Buoy. Viewing Local Weather Information near a Buoy You can select an area near a buoy to view forecast information. 1 From a weather chart, select a location on the chart. 2 Select Local Weather. 3 Select an option:

To view present weather conditions from a local weather service, select Current Condition. To view a local weather forecast, select Forecast. To view surface wind and barometric pressure information, To view wind and wave information, select Marine select Sea Surface. Bulletin. Weather Overlay The weather overlay superimposes weather and weather-related information on the Navigation chart, the Fishing chart, and the Perspective 3D chart view. The Navigation chart and the Fishing chart can show weather radar, height of cloud tops, lightning, weather buoys, county warnings, and hurricane warnings. The Perspective 3D chart view can show weather radar. Weather overlay settings configured for use on one chart are not applied to another chart. The weather overlay settings for each chart must be configured separately. NOTE: The Fishing chart is available with premium charts, in some areas. Viewing Weather Subscription Information You can view information about the weather services you have subscribed to and how many minutes have passed since the data for each service was updated. From a weather chart, select Menu > Subscription. Viewing Video WARNING To enter the lower and upper limits for the temperature range, select Lower Limit or Upper Limit, and enter the lower or upper limit. Do not view video or photos while operating the vessel. Failure to pay attention to the conditions on the water can result in vessel damage, personal injury, or death. Visibility Information Visibility is the forecast maximum horizontal distance that can be seen at the surface, as shown in the legend on the left of the screen. Variations in the visibility shading show the forecast change in surface visibility. NOTE: This feature is not available on all devices and in all subscriptions. Select Charts > Visibility. Before you can view video, you must connect to a compatible source. Compatible devices include video devices connected to the ports on the chartplotter or to the Garmin Marine Network, as well as supported network (IP-based) video cameras, encoders, and thermal cameras. Select A/V, Gauges, Controls > Video. Viewing Video 55 Selecting a Video Source 1 From the video screen, select Menu > Source. 2 Select the source of the video feed. Alternating Among Multiple Video Sources If you have two or more video sources, you can alternate between them using a specific time interval. 1 From the video screen, select Menu > Source > Alternate. 2 Select Time, and select the amount of time each video appears. 3 Select Source, and select the video sources to add to the alternating sequence. Networked Video Devices NOTICE A Garmin Power over Ethernet (PoE) Isolation Coupler (P/N 010-10580-10) must be used when connecting Ethernet devices, such as FLIR cameras, to a Garmin Marine Network. Connecting an Ethernet device directly to a Garmin Marine Network chartplotter damages the Garmin chartplotter and may damage the Ethernet device. Before you can view and control video devices such as IP cameras, encoders, and thermal cameras using your chartplotter, you must have a compatible video device connected to your chartplotter, and you must have a marine network cable Power over Ethernet (PoE) isolation coupler. Go to garmin.com for a list of compatible devices or to purchase a PoE Isolation Coupler. You can connect multiple supported video cameras and up to two video encoders to the Garmin Marine Network. You can select and view up to four video sources at once. Chartplotters with multiple composite built-in video inputs can display a single built-in video input only. When the cameras are connected, the network detects them automatically and displays them in the source list. Using Video Presets on Networked Video Cameras You can save, name, and activate video presets for each networked video source. Saving Video Presets on a Networked Video Camera 1 From a video screen, touch the screen. The video controls appear on the screen. 2 Hold a video preset button. A green light indicates the setting is stored. Naming Video Presets on a Networked Video Camera 1 From a video screen, select Menu > Video Setup > Presets. 2 Select a preset. 3 Select Rename. 4 Enter preset name. Activating Video Presets on a Networked Video Camera You can quickly return networked cameras to preset values. 1 From a video screen, touch the screen. The video controls appear on the screen. 2 Select a video preset. The camera restores the video settings saved for that preset. TIP: You can also save and activate presets using the video menu. Camera Settings Some cameras provide additional options to control the camera view. NOTE: Not all options are available on all camera models and chartplotter models. Refer to the camera manual for a list of available features. You may need to update the camera software to use this feature. From the infrared video screen, select Menu. IR Blend: Selects the infrared effect to MSX (Multi-Spectral Dynamic Imaging) mode or CTV (Color Thermal Vision) mode, and allows you to blend the effects. IR/Visible: Displays an infrared or visible light image. Scan: Surveys the surrounding area. Freeze: Pauses the camera image. Change Colors: Selects the color scheme of the infrared image. Change Scene: Selects the infrared image mode, such as day, night, MOB, or docking. Video Setup: Opens more video options. Video Settings Some cameras provide additional setup options. NOTE: Not all options are available on all camera models and chartplotter models. You may need to update the camera software to use this feature. From the video screen, select Menu > Video Setup. Set Input: Associates the camera with a video source. Mirror: Reverses the image like a rearview mirror. Standby: Places the camera in standby mode to conserve power and protect the lens when not in use. Home Position: Sets the home position of the camera. Scan Speed: Sets how quickly the camera moves during a scan. Scan Width: Sets the width of the image captured by the camera during a scan. Stabilization: Stabilizes the picture using mechanical means. Low Light: Optimizes the video for low-light environments. Aspect: Sets the aspect ratio. Defog: Optimizes the video for foggy environments. Dynamic Range: Sets the range to wide or standard. E. Stabilization: Stabilizes the picture using software image processing. Light: Controls the camera's integrated light source to help illuminate the environment. Name: Allows you to enter a new name for this camera. FLIR Menu: Provides access to the settings for the camera. Associating the Camera to a Video Source You may need to associate the camera with a video source. 1 From the video screen, select Menu > Source. 2 Select the camera. 3 Select Video Setup > Set Input. 4 Select the video input. Video Camera Movement Control NOTICE Do not aim the camera at the sun or extremely bright objects. Damage to the lens may occur. Always use the chartplotter controls or buttons to pan and tilt the camera. Do not manually move the camera unit. Manually moving the camera may damage the camera. NOTE: This feature is available only when a compatible camera is connected. You may need to update the camera software to use this feature. You can control the movements of the connected video cameras that support panning, tilting, and zooming. 56 Viewing Video Controlling Video Cameras Using On-Screen Controls On-screen controls allow you to control pan-tilt-zoom (PTZ) cameras. Refer to the camera manual for a list of available features. 1 From a video screen, touch the screen. The video controls appear on the screen. 2 Select an option:

To zoom in and out, use the zoom button. To pan or tilt the camera, use the compass rose. TIP: Hold within the compass rose to continue to move the camera in the desired direction. Controlling a Video Camera Using Gestures When a networked video camera supports gesture responses, you can control pan-tilt-zoom cameras using gestures directly on the chartplotter screen. Check your camera user manual for a list of available features. TIP: Using gestures allows video control without displaying the video controls. 1 From a video screen, touch the screen. 2 Select an option:

through the camera settings (Connecting a VIRB Action Camera, page 57). 1 Set up the chartplotter's WiFi network (Setting Up the WiFi Wireless Network, page 8). 2 Bring the camera near the chartplotter. 3 On the VIRB 360 camera main menu, select Wireless > Wi-

4 If necessary, select the Wi-Fi toggle switch to enable the Fi. WiFi technology. 5 Press 6 On the chartplotter, select A/V, Gauges, Controls > VIRB to select WPS, and press OK.

The camera searches for the WiFi network and connects. You can control the camera using the chartplotter. Connecting a VIRB Action Camera You connect a VIRB action camera to the chartplotter using the camera settings. If you are connecting a VIRB 360 camera, connect through the VIRB app (Connecting a VIRB 360 Action Camera, page 57). 1 Set up the chartplotter's WiFi network (Setting Up the WiFi To zoom in and out with the camera, use pinch and zoom Wireless Network, page 8). To pan or tilt the camera, swipe the screen in the desired 2 From the VIRB camera main menu, select Wireless > Wi-Fi

> Status to turn on WiFi wireless technology. gestures. direction. Configuring the Video Appearance NOTE: Not all options are available on all camera models and chartplotter models. 1 From the video screen, select Menu > Video Setup. 2 Select an option:

To show the video using a stretched aspect ratio, select Aspect > Stretch. The video cannot be stretched beyond the dimensions provided by the connected video device, and it may not fill the entire screen. To show the video using a standard aspect ratio, select To adjust the brightness, select Brightness, and select Aspect > Standard. Up, Down, or Auto. To adjust the color saturation, select Saturation, and select Up, Down, or Auto. To adjust the contrast, select Contrast, and select Up, Down, or Auto. To allow the chartplotter to automatically select the source format, select Standard > Auto. Garmin VIRB Action Cameras WARNING Do not view video or photos while operating the vessel. Failure to pay attention to the conditions on the water can result in vessel damage, personal injury, or death. Most VIRB action cameras connect to the chartplotter from the camera menu (Connecting a VIRB Action Camera, page 57). The VIRB 360 camera connects using WPS (Connecting a VIRB 360 Action Camera, page 57). In this manual, the term "VIRB action camera" refers to all models, except in the instructions on how to connect. In that case, as listed above, the term "VIRB 360 camera" refers to only the 360 model. 3 Select Mode > Connect. 4 Select Add New. The camera searches for nearby WiFi networks. 5 Select the chartplotter's WiFi network, and enter the network password. The app and the camera connect to the chartplotter's WiFi network. You can control the camera using the chartplotter. Controlling the VIRB Action Camera with the Chartplotter Before you can control a VIRB action camera with the chartplotter, you must connect the devices using a wireless connection. You can connect up to five VIRB action cameras to the chartplotter. After you connect the VIRB action camera with the chartplotter, a new option is added to A/V, Gauges, Controls. You can start and stop recording on the VIRB action camera using the chartplotter. NOTE: The VIRB image shown on the chartplotter is a in a lower resolution than the VIRB action camera records. To view the high-resolution video, view the video on a computer or television. 1 Select A/V, Gauges, Controls > VIRB. 2 Select an option:

To take a still photograph, select To begin recording, select

. When recording, the remaining recording memory is shown. To stop recording, select again. If you have more than one VIRB action camera connected, use the arrows to select a different action camera to control. To view stored videos or images, select To pan and tilt the VIRB 360, drag your finger on the

. Connecting a VIRB 360 Action Camera You can connect a VIRB 360 action camera to the chartplotter using WPS. If you are connecting a VIRB camera, connect screen. To return the VIRB 360 view to the home position, select Viewing Video 57 Controlling the VIRB Action Camera Video Playback You can view VIRB action camera video and images using the chartplotter. NOTE: The VIRB playback on the chartplotter is shown in the same quality as the live view on the chartplotter. To view the high-resolution video, view the video on a computer or television. 1 From the VIRB screen, select 2 Wait a few seconds for the thumbnail images to load. 3 Select a video or image. 4 Control the playback using the on-screen buttons or menu

. options:

To stop the video, select To pause the video, select To replay the video, select To play the video, select

. To skip ahead or back in the video, drag the slider. Deleting a VIRB Video You can delete a video or image from the VIRB action camera. 1 Open the VIRB video or image to delete. 2 Select Menu > Delete File. Starting a VIRB Video Slideshow You can view a slideshow of the videos and images on the VIRB action camera. 1 From the VIRB screen, select 2 Wait a few seconds for the thumbnail images to load. 3 Select a video or image. 4 Select Menu > Start Slideshow. To stop the slideshow, selcet Menu > Stop Slideshow. VIRB Action Camera Settings NOTE: Not all options and settings apply to all camera models. Select A/V, Gauges, Controls > VIRB > Menu. Name: Allows you to enter a new name for the VIRB action camera. Recording: Starts and stops recording. Take Photo: Takes a still photograph. Playback: Allows you to view video recordings and photos. Freeze: Pauses the camera image. Sleep: Puts the VIRB action camera into a low power mode to conserve battery power. Not available on the VIRB 360 camera. Video Setup: Sets up the video (VIRB Action Camera Video Setup Settings, page 58). Edit Overlays: Adjusts the data shown on the screen

(Customizing the Data Overlays, page 5). VIRB Action Camera Video Setup Settings NOTE: Not all options and settings apply to all camera models. Select A/V, Gauges, Controls > VIRB > Menu > Video Setup. Aspect: Sets the video aspect ratio. Video Mode: Sets the video mode. For example, you can select the Slow-Mo option to shoot slow motion videos. Video Size: Sets the size or pixel dimensions of videos. Video FPS: Sets the frames per second. Video Timestamp: Adds the date and time a video was recorded. Photo Timestamp: Adds the date and time a photo was taken. Photo Size: Sets the size or pixel dimensions of photos. Field of View: Sets the zoom level. Lens Mode: Sets which lens or lenses the camera uses while shooting video. Mirror: Allows you to flip or mirror the video. Rotation: Allows you to rotate the camera angle. Adding the VIRB Action Camera Controls to Other Screens Before you can control a VIRB action camera with the chartplotter, you must connect the devices using a wireless connection (Connecting a Wireless Device to the Chartplotter, page 8). You can add the VIRB action camera control bar to other screens. This allows you to start and stop recording from other functions in the chartplotter. 1 Open the screen to which you want to add the VIRB action camera control bar. 2 Select Menu > Edit Overlays > Bottom Bar > VIRB Bar. When viewing a screen that has the VIRB action camera controls, you can select VIRB action camera. to open the full screen view of the HDMI Out Video Considerations NOTICE To prevent corrosion due to moisture, you must use Garmin GPSMAP accessory cables when connecting the chartplotter to the video display. Using different cables voids your warranty. The GPSMAP A12/12x3 chartplotter models have HDMI out capability to duplicate the chartplotter screen on another device, such as a television or monitor. The Garmin GPSMAP HDMI accessory cable is 4.5 m (15 ft.) long. If you need a longer cable, you should use an active HDMI cable only. You need an HDMI coupler to connect the two HDMI cables. You must make all cable connections in a dry environment. Item Description GPSMAP A12/12x3 chartplotter GPSMAP HDMI cable (HDMI OUT) Display with an HDMI In port, such as a computer or television Dry environment, protected from moisture Pairing the GC 100 Camera with a Garmin Chartplotter Before you can connect a wireless device to the chartplotter wireless network, you must configure the chartplotter wireless network. 1 With the camera within an unobstructed 76 m (250 ft.) of the chartplotter, quickly press three times. 2 On the chartplotter, select Settings > Communications >

Wireless Devices > Garmin Camera > Start. 3 Follow the on-screen instructions. 58 Viewing Video Device Configuration System Settings Select Settings > System. Sounds and Display: Adjusts the display and audio settings. GPS: Provides information about the GPS satellites and settings. System Information: Provides information about the devices on the network and the software version. Station Information: Adjusts the setup of the station. Auto Power Up: Controls which devices turn on automatically when power is applied. Auto Power Off: Automatically turns off the system after it has been asleep for the selected length of time. Simulator: Turns the simulator on or off and allows you to set the time, date, speed, and simulated location. Sounds and Display Settings Select Settings > System > Sounds and Display. Beeper: Turns on and off the tone that sounds for alarms and selections. Backlight: Sets the backlight brightness. You can select the Auto option to adjust the backlight brightness automatically based on the ambient light. Backlight Sync: Synchronizes the backlight brightness of other chartplotters in the station. Color Mode: Sets the device to display day or night colors. You can select the Auto option to allow the device to set day or night colors automatically based on the time of day. Background: Sets the background image. Startup Image: Sets the image that appears when you turn on the device. the device. Startup Layout: Sets the layout that appears when you turn on Screen Lock: Sets the anti-theft feature that requires a security PIN (Personal Identification Number) to prevent unauthorized use of the device (Enabling Screen Lock, page 6). GPS Settings NOTE: Not all options are available on all models. Select Settings > System > GPS. Skyview: Shows the relative position of GPS satellites in the sky. WAAS/EGNOS: Turns on or off WAAS data (in North America) or EGNOS data (in Europe), which can provide more-

accurate GPS position information. When using WAAS or EGNOS data, the device may take longer to acquire satellites. Galileo: Turns on or off Galileo data (European Union satellite system). When the system is used in situations with poor sky visibility, Galileo data can be used in combination with GPS to provide more accurate position information. Speed Filter: Averages the speed of your vessel over a short period of time for smoother speed values. Source: Allows you to select the preferred source for GPS data. Station Settings Select Settings > System > Station Information. Change Station: Sets the entire station to a new set of defaults based on the location of this station. You can also select to use this display as a stand-alone, individual display, instead of grouping it with other displays to make a station. GRID Pairing: Allows you to pair a GRID remote input device with this station. Display Order: Sets the order of the displays, which is important when using a GRID remote input device. Autopilot Enabled: Allows you to control the autopilot from this Reset Layouts: Resets the layouts in this station to the factory device. default settings. Reset Station Settings: Resets all station settings to on all connected devices in the station to the factory default settings, and requires initial station setup. Viewing System Software Information You can view the software version, the basemap version, all supplemental map information (if applicable), the software version for an optional Garmin radar (if applicable), and the unit ID number. You may need this information to update the system software or to purchase additional map data information. Select Settings > System > System Information >

Software Information. Viewing the Event Log The event log shows a list of system events. Select Settings > System > System Information > Event Log. Viewing E-label Regulatory and Compliance Information The label for this device is provided electronically. The e-label may provide regulatory information, such as identification numbers provided by the FCC or regional compliance markings, as well as applicable product and licensing information. Not available on all models. 1 Select Settings. 2 Select System. 3 Select Regulatory Information. Preferences Settings Select Settings > Preferences. Units: Sets units of measure. Language: Sets the on-screen text language. Navigation: Sets navigation preferences. Keyboard Layout: Arranges the keys on the on-screen Screenshot Capture: Allows the device to save images of the Menu Bar Display: Shows or automatically hides the menu bar when it is not needed. Units Settings Select Settings > Preferences > Units. System Units: Sets the unit format for the device. Variance: Sets the magnetic declination, the angle between magnetic north and true north, for your present location. North Reference: Sets the direction references used in calculating heading information. True sets geographic north as the north reference. Grid sets grid north as the north reference (000). Magnetic sets the magnetic north as the north reference. Position Format: Sets the position format in which a given location reading appears. Do not change this setting unless you are using a map or chart that specifies a different position format. GLONASS: Turns on or off GLONASS data (Russia satellite keyboard. system). When the system is used in situations with poor sky visibility, GLONASS data can be used in combination with GPS to provide more accurate position information. screen. Device Configuration 59 Map Datum: Sets the coordinate system on which the map is structured. Do not change this setting unless you are using a map or chart that specifies a different map datum. Time: Sets the time format, time zone, and daylight saving time. Navigation Settings NOTE: Some settings and options require additional charts or hardware. Select Settings > Preferences > Navigation. Route Labels: Sets the type of labels shown with route turns on the map. Turn Transition: Adjusts how the chartplotter transitions to the next turn or leg or the route. You can set the transition to be based on time or distance before the turn. You can increase the time or distance value to help improve the accuracy of the autopilot when navigating a route or an Auto Guidance line with many frequent turns or at higher speeds. For straighter routes or slower speeds, lowering this value can improve autopilot accuracy. Speed Sources: Sets the source for the speed readings. Auto Guidance: Sets the measurements for the Preferred Depth, Vertical Clearance, and Shoreline Distance, when you are using some premium maps. Route Start: Selects a starting point for route navigation. Auto Guidance Path Configurations CAUTION The Preferred Depth and Vertical Clearance settings influence how the chartplotter calculates an Auto Guidance path. If an area has an unknown water depth or an unknown obstacle height, the Auto Guidance path is not calculated in that area. If an area at the beginning or the end of an Auto Guidance path is shallower than the Preferred Depth or lower than the Vertical Clearance settings, the Auto Guidance path may not be calculated in that area, depending on the map data. On the chart, the course through those areas appears as a gray line or a magenta and gray striped line. When your boat enters one of those areas, a warning message appears. NOTE: Auto Guidance is available with premium charts, in some areas. NOTE: Not all settings apply to all maps. You can set the parameters the chartplotter uses when calculating an Auto Guidance path. Preferred Depth: Sets the minimum water depth, based on chart depth data, that your boat can safely travel over. NOTE: The minimum water depth for the premium charts

(made before 2016) is 3 feet. If you enter a value of less than 3 feet, the charts only use depths of 3 feet for Auto Guidance path calculations. Vertical Clearance: Sets the minimum height of a bridge or obstacle, based on chart data, that your boat can safely travel under. Shoreline Distance: Sets how close to the shore you want the Auto Guidance path to be placed. The Auto Guidance path may move if you change this setting while navigating. The available values for this setting are relative, not absolute. To ensure that the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Auto Guidance path using one or more familiar destinations that require navigation through a narrow waterway (Adjusting the Distance from Shore, page 21). Adjusting the Distance from Shore The Shoreline Distance setting indicates how close to the shore you want the Auto Guidance line to be placed. The Auto Guidance line may move if you change this setting while navigating. The available values for the Shoreline Distance setting are relative, not absolute. To ensure the Auto Guidance line is placed the appropriate distance from shore, you can assess the placement of the Auto Guidance line using one or more familiar destinations that require navigation through a narrow waterway. 1 Dock your vessel or drop the anchor. 2 Select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Normal. 3 Select a destination that you have navigated to previously. 4 Select Navigate To > Auto Guidance. 5 Review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. 6 Select an option:

If the placement of the Auto Guidance line is satisfactory, select Menu > Navigation Options > Stop Navigation, and proceed to step 10. If the Auto Guidance line is too close to known obstacles, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Far. If the turns in the Auto Guidance line are too wide, select Settings > Preferences > Navigation > Auto Guidance

> Shoreline Distance > Near. 7 If you selected Near or Far in step 6, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway. 8 Select an option:

If the placement of the Auto Guidance line is satisfactory, select Menu > Navigation Options > Stop Navigation, and proceed to step 10. If the Auto Guidance line is too close to known obstacles, select Settings > Preferences > Navigation > Auto Guidance > Shoreline Distance > Farthest. If the turns in the Auto Guidance line are too wide, select Settings > Preferences > Navigation > Auto Guidance

> Shoreline Distance > Nearest. 9 If you selected Nearest or Farthest in step 8, review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest. As a result, the chartplotter may not reposition the Auto Guidance line, unless the destination selected requires navigation through a narrow waterway. 10Repeat steps 3 through 9 at least once more, using a different destination each time, until you are familiar with the functionality of the Shoreline Distance setting. Communications Settings NMEA 0183 Settings Select Settings > Communications > NMEA 0183 Setup. Port Types: See Setting the Communication Format for Each NMEA 0183 Port, page 61. Output Sentences: See Configuring NMEA 0183 Output Sentences, page 61. Position Precision: Adjusts the number of digits to the right of the decimal point for transmission of NMEA output. 60 Device Configuration XTE Precision: Adjusts the number of digits to the right of the decimal point for NMEA crosstalk error output. Setting Alarms Waypoint IDs: Sets the device to transmit waypoint names or numbers via NMEA 0183 while navigating. Using numbers may resolve compatibility issues with older NMEA 0183 autopilots. Restore Defaults: Restores the NMEA 0183 settings to the original factory defaults. Diagnostics: Displays NMEA 0183 diagnostic information. Configuring NMEA 0183 Output Sentences You can enable and disable NMEA 0183 output sentences. 1 Select Settings > Communications > NMEA 0183 Setup >

Output Sentences. 2 Select an option. 3 Select one or more NMEA 0183 output sentences, and select 4 Repeat steps 2 and 3 to enable or disable additional output Back. sentences. Setting the Communication Format for Each NMEA 0183 Port You can configure the communication format for each internal NMEA 0183 port when connecting your chartplotter to external NMEA 0183 devices, a computer, or other Garmin devices. 1 Select Settings > Communications > NMEA 0183 Setup >

Port Types. 2 Select an input or output port. 3 Select a format:

To support the input or output of standard NMEA 0183 data, DSC, and sonar NMEA input support for the DPT, MTW, and VHW sentences, select NMEA Std.. To support the input or output of standard NMEA 0183 data for most AIS receivers, select NMEA High Speed. To support the input or output of Garmin proprietary data for interfacing with Garmin software, select Garmin. 4 Repeat steps 23 to configure additional input or output ports. NMEA 2000 Settings Select Settings > Communications > NMEA 2000 Setup. Device List: Displays the devices connected to the network and allows you to set options for some transducers connected using the NMEA 2000 network. Label Devices: Changes the labels for available connected devices. Naming Devices and Sensors on the Network You can name devices and sensors connected to the Garmin Marine Network and the NMEA 2000 network. 1 Select Settings > Communications. 2 Select Marine Network or NMEA 2000 Setup > Device List. 3 Select a device from the list on the left. 4 Select Review > Change Name. 5 Enter the name, and select Done. Marine Network The Marine Network allows you to share data from Garmin peripheral devices with the chartplotters quickly and easily. You can connect a chartplotter to the Marine Network to receive data from and share data with other devices and chartplotters that are compatible with the Marine Network. Select Settings > Communications > Marine Network. CAUTION The Beeper setting must be turned on to make alarms audible

(Sounds and Display Settings, page 59). Failure to set audible alarms could lead to injury or property damage. Navigation Alarms Select Settings > Alarms > Navigation. Arrival: Sets an alarm to sound when you are within a specified distance or time from a turn or a destination. Anchor Drag: Sets an alarm to sound when you exceed a specified drift distance while anchored. Off Course: Sets an alarm to sound when you are off course by a specified distance. Boundary Alarms: Disables and enables all boundary alarms. Setting the Anchor Drag Alarm You can set an alarm to sound if you have moved more than an allowable distance. This is very useful when anchoring overnight. 1 Select Settings > Alarms > Navigation > Anchor Drag. 2 Select Alarm to turn on the alarm. 3 Select Set Radius, and select a distance on the chart. 4 Select Back. System Alarms Alarm Clock: Sets an alarm clock. Unit Voltage: Sets an alarm to sound when the battery reaches a specified low voltage. GPS Accuracy: Sets an alarm to sound when the GPS location accuracy falls outside the user-defined value. Sonar Alarms NOTE: Not all options are available on all transducers. From an applicable sonar view, select Menu > Sonar Setup >

Alarms. You can also open the sonar alarms by selecting Settings >

Alarms > Sonar. Shallow Water: Sets an alarm to sound when the depth is less Deep Water: Sets an alarm to sound when the depth is greater than the specified value. than the specified value. FrontV Alarm: Sets an alarm to sound when the depth in front of the vessel is less than the specified value, which can help you avoid running aground (Setting the FrontV Depth Alarm, page 33). This alarm is available only with Panoptix FrontV transducers. Water Temp.: Sets an alarm to sound when the transducer reports a temperature that is 2F (1.1C) above or below the specified temperature. Contour: Sets an alarm to sound when the transducer detects a suspended target within the specified depth from the surface of the water and from the bottom. Fish Fish: Sets an alarm to sound when the device detects a suspended target. detected. fish are detected. detected. sets the alarm to sound when fish of all sizes are sets the alarm to sound only when medium or large sets the alarm to sound only when large fish are Device Configuration 61 Setting Weather Alarms Before you can set weather alarms, you must have a compatible chartplotter connected to a weather device, such as a GXM device, and have a valid weather subscription. 1 Select Settings > Alarms > Weather. 2 Turn on alarms for specific weather events. If you want to know the true water depth and the transducer is installed below the water line, measure the distance from the bottom of the transducer up to the water line. NOTE: This option is only available when you have valid depth data. 1 Measure the distance:

If the transducer is installed at the water line or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat. Enter this value as a positive number. If the transducer is installed at the bottom of the keel and you want to know the true depth of the water, measure the distance from the transducer to the water line. Enter this value in as a negative number. Setting the Fuel Alarm Before you can set a fuel level alarm, a compatible fuel flow sensor must be connected to the chartplotter. You can set an alarm to sound when the total amount of remaining onboard fuel reaches the level you specify. 1 Select Settings > Alarms > Fuel > Set Total Fuel Onboard 2 Enter the remaining amount of fuel that triggers the alarm,

> On. and select Done. My Vessel Settings NOTE: Some settings and options require additional charts or hardware. Select Settings > My Vessel. Transducers: Shows all transducers on the network, allows you to change transducers, and allows you to view diagnostic information (Selecting the Transducer Type, page 28). Depth and Anchoring: Allows you to enter information about the keel (Setting the Keel Offset, page 24) and the anchor. The Anchor Height value is the height of the anchor above the waterline. The Anchor Scope value is the ratio of the length of anchor rode in use to the vertical distance from the bow of the vessel to the bottom of the water. These anchor settings are used to calculate the Target Anchor Rode date field. Temp. Offset: Allows you to set an offset value to compensate for the water temperature reading from a NMEA 0183 water-

temperature sensor or a temperature-capable transducer

(Setting the Water Temperature Offset, page 62). Calibrate Water Speed: Calibrates the speed-sensing transducer or sensor (Calibrating a Water-Speed Device, page 63). 2 Complete an action:

If the transducer is connected to the chartplotter or a sonar module, select Settings > My Vessel > Depth and Anchoring > Keel Offset. If the transducer is connected to the NMEA 2000 network, select Settings > Communications > NMEA 2000 Setup

> Device List, select the transducer, and select Review >

Keel Offset. if the transducer is installed at the water line, or if the transducer is installed at the bottom of the Fuel Capacity: Sets the combined fuel capacity of all the fuel tanks on your vessel (Setting the Fuel Capacity of the Vessel, page 47). Vessel Type: Enables some chartplotter features based on the 3 Select select keel. boat type. 4 Enter the distance measured in step 1. CZone: Sets the digital switching circuits. SeaStar Instance: Sets the digital switching circuits. System Profiles: Allows you to save your system profile to a memory card and import system profile settings from a memory card. This can be helpful for charter or fleet vessels, and for sharing your setup information with a friend. Hull ID Number: Allows you to enter the Hull Identification Number (HIN).The HIN might be permanently affixed to the upper starboard side of the transom or outboard side. Optimus Steering: Allows you to adjust the Optimus steering parameters. Setting the Keel Offset You can enter a keel offset to compensate the water depth reading for the transducer installation location. This allows you to view the depth of the water below the keel or the true depth of the water, depending on your needs. If you want to know the water depth below the keel or the lowest point of your boat and the transducer is installed at the water line or anywhere above the end of the keel, measure the distance from the transducer location to the keel of the boat. Setting the Water Temperature Offset The temperature offset compensates for the temperature reading from a temperature sensor or temperature-capable transducer. 1 Measure the water temperature using the temperature sensor or temperature-capable transducer that is connected to the network. 2 Measure the water temperature using a different temperature sensor or a thermometer that is known to be accurate. 3 Subtract the water temperature measured in step 1 from the water temperature measured in step 2. This value is the temperature offset. Enter this value in step 5 as a positive number if the sensor measures the water temperature as being colder than it actually is. Enter this value in step 5 as a negative number if the sensor measures the water temperature as being warmer than it actually is. 4 Complete an action:

If the sensor or transducer is connected to the chartplotter or a sonar module, select Settings > My Vessel > Temp. Offset. 62 Device Configuration If the sensor or transducer is connected to the NMEA 2000 network, select Settings > Communications >

NMEA 2000 Setup > Device List, select the transducer, and select Review > Temp. Offset. 5 Enter the temperature offset value calculated in step 3. Calibrating a Water-Speed Device If you have a speed sensor or a speed-sensing transducer connected, you can calibrate that speed-sensing device to improve the accuracy of water-speed data displayed by the chartplotter. 1 Complete an action:

If the sensor or transducer is connected to the chartplotter or a sonar module, select Settings > My Vessel >

Calibrate Water Speed. If the sensor or transducer is connected to the NMEA 2000 network, select Settings > Communications >

NMEA 2000 Setup > Device List, select the transducer, and select Review > Calibrate Water Speed. 2 Follow the on-screen instructions. If the boat is not moving fast enough or the speed sensor is not registering a speed, a message appears. 3 Select OK, and safely increase the boat speed. 4 If the message appears again, stop the boat, and ensure the speed-sensor wheel is not stuck. 5 If the wheel turns freely, check the cable connections. 6 If you continue to get the message, contact Garmin product support. Other Vessels Settings When your compatible chartplotter is connected to an AIS device or VHF radio, you can set up how other vessels are displayed on the chartplotter. Select Settings > Other Vessels. AIS: Enables and disables AIS signal reception. DSC: Enables and disables digital selective calling (DSC). Collision Alarm: Sets the collision alarm (Setting the Safe-Zone Collision Alarm, page 12). AIS-EPIRB Test: Enables test signals from Emergency Position Indicating Radio Beacons (EPRIB). AIS-MOB Test: Enables test signals from man overboard (MOB) devices. AIS-SART Test: Enables test transmissions from Search and Rescue Transponders (SART). Settings that are Synced on the Garmin Marine Network The following devices sync certain settings when connected to the Garmin Marine Network. ECHOMAP 70 series GPSMAP 507 series (software version 3.0 or later) GPSMAP 701 series (software version 3.0 or later) GPSMAP 702 series GPSMAP 800 series GPSMAP 902 series GPSMAP 1000 series GPSMAP 1002 series GPSMAP 1202 series GPSMAP 7400/7600 series GPSMAP 8400/8600/8700 series The following settings are synced, if applicable, to the device. Alarm Settings (also syncs alarm acknowledgment):

Arrival Anchor Drag Off Course GPS Accuracy Shallow Water Deep Water (Not available in the GPSMAP 8400/8600 series) Water Temp. Contour (Not available in echoMAP 70s and GPSMAP 507/701 series) Fish Collision Alarm General Settings:

Auto Guidance Preferred Depth Auto Guidance Vertical Clearance Beeper Color Mode Keyboard Layout Language Map Datum North Reference Position Format System Units Calibrate Water Speed Radar Antenna Size Chart Settings:

Chart Borders Hazard Colors Heading Line Land POIs Light Sectors Navaid Size Navaid Type Photo Points Preferred Depth Shallow Shading Service Points Vessel Icon (Cannot be synced between all models) Restoring the Original Chartplotter Factory Settings NOTE: This affects all devices on the network. 1 Select Settings > System > System Information > Reset. 2 Select an option:

To reset the device settings to the factory default values, select Reset Default Settings. This restores the default configuration settings, but does not remove saved user data, maps, or software updates. To reset all settings in all devices in the station to the factory default values, select Reset Station Settings. This restores the default configuration settings, but does not remove saved user data, maps, or software updates To clear saved data, such as waypoints and routes, select Delete User Data. This does not affect maps or software updates. To clear saved data and reset device settings to the factory default values, disconnect the chartplotter from the Garmin Marine Network, and select Delete Data and Device Configuration 63 Reset Settings. This does not affect maps or software updates. Sharing and Managing User Data You can share user data between compatible devices. User data includes waypoints, saved tracks, routes, and boundaries. You can share data across the Garmin Marine Network. You can share and manage user data using a memory card. You must have a memory card installed in the device. This device supports up to a 32 GB memory card, formatted to FAT32. Selecting a File Type for Third-Party Waypoints and Routes You can import and export waypoints and routes from third-party devices. 1 Insert a memory card into the card slot. 2 Select Info > User Data > Data Transfer > File Type. 3 Select GPX. To transfer data with Garmin devices again, select the ADM file type. Copying User Data from a Memory Card You can transfer user data from a memory card to transfer from other devices. User data includes waypoints, routes, Auto Guidance paths, tracks, and boundaries. NOTE: Only boundary files with an .adm extension are supported. 1 Insert a memory card into a card slot. 2 Select Info > User Data > Data Transfer. 3 If necessary, select the memory card to copy data to. 4 Select an option:

To transfer data from the memory card to the chartplotter and combine it with existing user data, select Merge from Card. To transfer data from the memory card to the chartplotter and overwrite existing user data, select Replace from Card. 5 Select the file name. Copying User Data to a Memory Card You can save user data to a memory card to transfer to other devices. User data includes waypoints, routes, Auto Guidance paths, tracks, and boundaries. 1 Insert a memory card into the card slot. 2 Select Info > User Data > Data Transfer > Save to Card. 3 If necessary, select the memory card to copy the data to. 4 Select an option:

To create a new file, select Add New File, and enter a name. To add the information to an existing file, select the file from the list, and select Save to Card. Updating Built-In Maps with a Memory Card and Garmin Express You can update the built-in maps using Garmin Express and a memory card. 1 Insert a memory card into the computer's card slot. 2 Open the Garmin Express application. If you do not have the Garmin Express application installed on your computer, you can download it from garmin.com

/express. 3 If necessary, register your device (Registering Your Device Using the Garmin Express App, page 65). 4 Click Vessel > View Details. 5 Click Download next to the map to update. 6 Follow the on-screen instructions to complete the download. 7 Wait while the update downloads. The update may take an extended period of time. 8 After the download is complete, eject the card from the 9 Insert the memory card into the card slot (Memory Cards, computer. page 2). 10On the chartplotter, select Settings > System > System Information > Update Built-In Map. The updated chart appears on your chartplotter. Backing Up Data to a Computer 1 Insert a memory card into the card slot. 2 Select Info > User Data > Data Transfer > Save to Card. 3 Select a file name from the list, or select Add New File. 4 Select Save to Card. 5 Remove the memory card, and insert it into a card reader attached to a computer. 6 Open the Garmin\UserData folder on the memory card. 7 Copy the backup file on the card and paste it to any location on the computer. Restoring Backup Data to a Chartplotter 1 Insert a memory card into a card reader that is attached to the computer. 2 Copy a backup file from the computer to the memory card, into a folder named Garmin\UserData. 3 Insert a memory card into the card slot. 4 Select Info > User Data > Data Transfer > Replace from Card. Saving System Information to a Memory Card You can save system information to a memory card as a troubleshooting tool. A product support representative may ask you to use this information to retrieve data about the network. 1 Insert a memory card into the card slot. 2 Select Settings > System > System Information > Garmin Devices > Save to Card. 3 If necessary, select the memory card to save system information to. 4 Remove the memory card. Appendix ActiveCaptain and Garmin Express The ActiveCaptain and Garmin Express apps help you manage your Garmin chartplotter and other devices. ActiveCaptain: The ActiveCaptain mobile app provides an easy-to-use connection between your compatible mobile device and your compatible Garmin chartplotter, charts, and the Garmin Quickdraw Contours Community (ActiveCaptain App, page 6). The app allows you to monitor and track your boat with the OnDeck system, provides unlimited access to 64 Sharing and Managing User Data your cartography and a quick, mobile way to download new charts using the OneChart feature, provides a link to receive notifications on your chartplotter, and provides access to the ActiveCaptain Community for feedback on marinas and other boating points of interest. You can also use the app to plan your trip and sync user data. The app checks your devices for available updates, and notifies you when an update is available. Garmin Express: The Garmin Express desktop app allows you to use your computer and a memory card to download and update Garmin chartplotter software and charts (Garmin Express App, page 65). You should use the Garmin Express app for faster data transfer of larger downloads and updates, and to avoid possible data charges with some mobile devices. Function ActiveCaptain mobile app Garmin Express desktop app Register your new Garmin Marine device Update your Garmin chartplotter software Update your Garmin charts Download new Garmin charts Access the Garmin Quickdraw Contours Community to download and share contours with other users Monitor and track your boat with the OnDeck system Sync a mobile device with your Garmin chartplotter Access the ActiveCaptain Community for feedback on marinas and boating points of interest Receive smart notification on the chartplotter Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No No Garmin Express App The Garmin Express desktop app allows you to use your computer and a memory card to download and update Garmin device software and charts and register your devices. We recommend it for larger downloads and updates for faster data transfer and to avoid possible data charges with some mobile devices. Installing the Garmin Express App on a Computer You can install the Garmin Express app on a Windows or Mac computer. 1 Go to garmin.com/express. 2 Select Download for Windows or Download for Mac. 3 Follow the on-screen instructions. Registering Your Device Using the Garmin Express App NOTE: You should use the ActiveCaptain app and a mobile device to register the device (Getting Started with the ActiveCaptain App, page 6). Help us better support you by completing our online registration today. Keep the original sales receipt, or a photocopy, in a safe place. 1 Install the Garmin Express app on your computer (Installing the Garmin Express App on a Computer, page 65). 2 Insert a memory card into the card slot (Memory Cards, page 2). 3 Wait a few moments. Appendix The chartplotter opens the card management page and creates a file named GarminDevice.xml in the Garmin folder on the memory card. 4 Remove the memory card from your device. 5 Open the Garmin Express app on your computer. 6 Insert the memory card into your computer. 7 If necessary, select Get Started. 8 If necessary, while the application searches, select Sign In next to Have marine charts or devices? near the bottom of the screen. 9 Create or sign in to your Garmin account. 10Follow the on-screen instructions to set up your vessel. 11Select Add. The Garmin Express application searches the memory card for the device information. 12Select Add Device to register the device. When registration is complete, the Garmin Express application searches for additional charts and chart updates for your device. When you add devices to the chartplotter network, repeat these steps to register the new devices using the Garmin Express app. Updating Your Charts Using the Garmin Express App This device supports up to a 32 GB memory card, formatted to FAT32 with speed class 4 or higher. Use of an 8 GB or higher memory card with speed class 10 is recommended. Downloading the chart update may take up to a few hours. You should use a blank memory card for chart updates. The update process erases the content on the card and reformats the card. 1 Install the Garmin Express app on your computer (Installing the Garmin Express App on a Computer, page 65). 2 Open the Garmin Express app on your computer. 3 Select your vessel and device. 4 If chart updates are available, select Chart Updates >

Continue. 5 Read and agree to the terms. 6 Insert your chartplotter chart memory card into the computer. 7 Select the drive for the memory card. 8 Review the reformat warning, and select OK. 9 Wait while the chart update is copied to the memory card. NOTE: Copying the update file onto the card may take from a few minutes up to a few hours. 10Close the Garmin Express app. 11Eject the memory card from the computer. 12Turn on the chartplotter. 13After the home screen appears, insert the memory card into the card slot. NOTE: In order for the update instructions to appear, the device must be fully booted before the card is inserted. 14Select Update Software > Yes. 15Wait several minutes while the update process completes. 16When prompted, leave the memory card in place, and restart the chartplotter. 17Remove the memory card. NOTE: If the memory card is removed before the device restarts fully, the update is not complete. Software Updates You may need to update the software when you install a new device or add an accessory. 65 You can use the ActiveCaptain mobile app to update the device software (Updating Software with the ActiveCaptain App, page 7). You can also use the Garmin Express desktop app to update your chartplotter software (Loading the New Software on a Memory Card Using Garmin Express, page 66). This device supports up to a 32 GB memory card, formatted to FAT32 with speed class 4 or higher. Use of an 8 GB or higher memory card with speed class 10 is recommended. Before you update the software, you should check the software version installed on your device (Viewing System Software Information, page 59). Then, you can go to garmin.com/support

/software/marine.html, select See All Devices in this Bundle, and compare the installed software version to the software version listed for your product. If the software version installed on your device is older than the version listed on the website, you should update the software using the ActiveCaptain mobile app (Updating Software with the ActiveCaptain App, page 7) or the Garmin Express desktop app

(Loading the New Software on a Memory Card Using Garmin Express, page 66). Loading the New Software on a Memory Card Using Garmin Express You can copy the software update to a memory card using a computer with the Garmin Express app. This device supports up to a 32 GB memory card, formatted to FAT32 with speed class 4 or higher. Use of an 8 GB or higher memory card with speed class 10 is recommended. Downloading the software update may take from a few minutes up to a few hours. You should use a blank memory card for software updates. The update process erases the content on the card and reformats the card. 1 Insert a memory card into the card slot on the computer. 2 Install the Garmin Express app (Installing the Garmin Express App on a Computer, page 65). 3 Select your vessel and device. 4 Select Software Updates > Continue. 5 Read and agree to the terms. 6 Select the drive for the memory card. 7 Review the reformat warning, and select Continue. 8 Wait while the software update is copied to the memory card. NOTE: Copying the update file onto the card may take from a few minutes up to a few hours. 9 Close the Garmin Express app. 10Eject the memory card from the computer. After loading the update onto the memory card, install the software on the chartplotter (Updating the Device Software Using a Memory Card, page 66). Updating the Device Software Using a Memory Card To update the software using a memory card, you must obtain a software-update memory card or load the latest software onto a memory card using the Garmin Express app (Loading the New Software on a Memory Card Using Garmin Express, page 66). 1 Turn on the chartplotter. 2 After the home screen appears, insert the memory card into the card slot. NOTE: In order for the software update instructions to appear, the device must be fully booted before the card is inserted. 3 Select Update Software > Yes. 4 Wait several minutes while the software update process completes. 66 5 When prompted, leave the memory card in place, and restart the chartplotter. 6 Remove the memory card. NOTE: If the memory card is removed before the device restarts fully, the software update is not complete. Pairing the GRID Device with the Chartplotter from the Chartplotter NOTE: These steps are applicable to both the GRID device and the GRID 20 device. Before you can pair the GRID 20 device with the chartplotter to make the data connection, you must supply power using batteries, the included power cable, or a NMEA 2000 network connection. Before you can pair the GRID device with the chartplotter, you must connect it to the Garmin Marine Network. 1 Select Settings > System > Station Information > GRID Pairing > Add. 2 Select an action:

On the GRID remote input device, press SELECT. On the GRID 20 remote input device, press and until the remote control beeps three times. Pairing the GRID Device with the Chartplotter from the GRID Device NOTE: This is not applicable to the GRID 20 device. 1 On the GRID remote input device, press + and HOME at the same time. A selection page opens on all of the chartplotters on the Garmin Marine Network. 2 Rotate the wheel on the GRID remote input device to highlight Select on the chartplotter you want to control with the GRID remote input device. 3 Press SELECT. Rotating the GRID Remote Input Device For certain installation situations, you can rotate the orientation of the GRID device. NOTE: This is not applicable to the GRID 20 device. 1 Select Settings > Communications > Marine Network. 2 Select the GRID device. Cleaning the Screen Cleaners containing ammonia will harm the anti-reflective coating. NOTICE The device is coated with a special anti-reflective coating which is very sensitive to waxes and abrasive cleaners. 1 Apply an eyeglass lens cleaner specified as safe for anti-

reflective coatings to the cloth. 2 Gently wipe the screen with a soft, clean, lint-free cloth. Viewing Images on a Memory card You can view images that are saved on a memory card. You can view .jpg, .png, and .bmp files. 1 Insert a memory card with image files into the card slot. 2 Select Info > Image Viewer. 3 Select the folder containing the images. 4 Wait a few seconds for the thumbnail images to load. 5 Select an image. 6 Use the arrows to scroll through the images. Appendix 7 If necessary, select Menu > Start Slideshow. Screenshots You can capture a screenshot of any screen shown on your chartplotter as a .png file. You can transfer the screenshot to your computer. You can also view the screenshot in the image viewer (Viewing Images on a Memory card, page 66). Capturing Screenshots 1 Insert a memory card into the card slot. 2 Select Settings > Preferences > Screenshot Capture >

On. 3 Go to a screen you want to capture. 4 Hold Home for at least six seconds. Copying Screenshots to a Computer 1 Remove the memory card from the chartplotter, and insert it into a card reader that is attached to a computer. 2 From Windows Explorer, open the Garmin\scrn folder on the 3 Copy a .bmp file from the card and paste it to any location on memory card. the computer. Troubleshooting My device will not acquire GPS signals If the device is not acquiring satellite signals, there could be a few causes. If the device has moved a large distance since the last time it has acquired satellites or has been turned off for longer than a few weeks or months, the device may not be able to acquire the satellites correctly. Ensure the device is using the latest software. If not, update the device software (Software Updates, page 65). Make sure the device has a clear view of the sky so the antenna can receive the GPS signal. If it is mounted inside of a cabin, it should be close to a window so it can receive the GPS signal. My device will not turn on or keeps turning off Devices erratically turning off or not turning on could indicate an issue with the power supplied to the device. Check these items to attempt to troubleshoot the cause of the power issue. Make sure the power source is generating power. You can check this several ways. For example, you can check whether other devices powered by the source are functioning. Check the fuse in the power cable. The fuse should be located in a holder that is part of the red wire of the power cable. Check that the proper size fuse is installed. Refer to the label on the cable or the installation instructions for the exact fuse size needed. Check the fuse to make sure there is still a connection inside of the fuse. You can test the fuse using a multimeter. If the fuse is good, the multimeter reads 0 ohm. Check to make sure the device is receiving at least 12 V. To check the voltage, measure the female power and ground sockets of the power cable for DC voltage. If the voltage is less than 12 V, the device will not turn on. If the device is receiving enough power but does not turn on, contact Garmin product support. My device is not creating waypoints in the correct location You can manually enter a waypoint location to transfer and share data from one device to the next. If you have manually entered a waypoint using coordinates, and the location of the point does not appear where the point should be, the map datum and position format of the device may not match the map datum and position format originally used to mark the waypoint. Position format is the way in which the GPS receiver's position appears on the screen. This is commonly displayed as latitude/

longitude in degrees and minutes, with options for degrees, minutes and second, degrees only, or one of several grid formats. Map datum is a math model which depicts a part of the surface of the earth. Latitude and longitude lines on a paper map are referenced to a specific map datum. 1 Find out which map datum and position format was used when the original waypoint was created. If the original waypoint was taken from a map, there should be a legend on the map that lists the map datum and position format used to create that map. Most often this is found near the map key. 2 Select Settings > Preferences > Units. 3 Select the correct map datum and position format settings. 4 Create the waypoint again. Contacting Garmin Support Go to support.garmin.com for help and information, such as product manuals, frequently asked questions, videos, and customer support. In the USA, call 913-397-8200 or 1-800-800-1020. In the UK, call 0808 238 0000. In Europe, call +44 (0) 870 850 1241. Specifications GPSMAP 7x2/7x2 Plus Specifications Dimensions (W H D) Display size (W H) 22.4 14.3 5.4 cm (8.8 5.6 2.1 in.) 15.4 8.6 cm (6.1 3.4 in.) 7 in. diagonal Display resolution WVGA, 800 480 pixels Weight 0.86 kg (1.9 lb.) Compass-safe distance 71 cm (28 in.) Temperature range From -15 to 55C (from 5 to 131F) Material Water rating Fuse Input voltage Polycarbonate plastic and die-cast aluminum IEC 60529 IPX71 6 A, 125 V fast-acting From 10 to 32 Vdc Max. power usage at 10 Vdc 24 W Typical current draw at 12 Vdc 1.5 A Max. current draw at 12 Vdc 2.0 A NMEA 2000 LEN @ 9 Vdc 2 NMEA 2000 draw Max. waypoints Max. routes 75 mA max. 5,000 100 Max. active track points 50,000 points, 50 saved tracks Wireless frequency 2.4 GHz @ 17.6 dBm nominal Memory card HTML integration 2 SD card slots; 32 GB max. card size Compatible with OneHelm integration

(Plus models only) Appendix 67 1 The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. GPSMAP 9x2/9x2 Plus Specifications GPSMAP 7x3 Specifications Dimensions (W H D) Display size (W H) 25.6 16.2 5.2 cm (10.1 6.4 2.1 in.) 19.6 11.4 cm (7.7 4.5 in.) 9 in. diagonal Display resolution WSVGA, 1024 600 pixels Weight 9x2: 1.14 kg (2.5 lb.) 9x2 Plus: 1.27 kg (2.8 lb.) Compass-safe distance 76 cm (30 in.) Dimensions (W H D) 192.3 140.3 74.1 mm (7 9/16 5 1/2 2 15/16 in.) Clearance to next obstruction 27.8 mm (2 in.) Display size (W H) 154.6 91.0 mm (6 1/16 3 9/16 in.) 17.8 cm (7.0 in.) diagonal Display resolution WSVGA, 1024 600 pixels Weight 1.3 kg (2.8 lb.) Compass-safe distance 35 cm (13.78 in.) Temperature range From -15 to 55C (from 5 to 131F) Max. power usage at 10 Vdc Non-sonar models: 17.6 W Material Water rating Fuse Input voltage Polycarbonate plastic and die-cast aluminum IEC 60529 IPX71 6 A, 125 V fast-acting From 10 to 32 Vdc Max. power usage at 10 Vdc 27 W Typical current draw at 12 Vdc 1.3 A Max. current draw at 12 Vdc 2.3 A NMEA 2000 LEN @ 9 Vdc 2 NMEA 2000 draw Max. waypoints Max. routes 75 mA max. 5,000 100 Max. active track points 50,000 points, 50 saved tracks Wireless frequency 2.4 GHz @ 17.6 dBm nominal Memory card HTML integration 2 SD card slots; 32 GB max. card size Compatible with OneHelm integration

(Plus models only) GPSMAP 12x2 Touch/A12/12x2 Plus Specifications Dimensions (W H D) Display size (W H) 33.0 22.6 7.9 cm (13.0 8.9 3.1 in.) 26.2 16.3 cm (10.3 6.4 in.) 12 in. diagonal Display resolution WXGA, 1280 800 pixels Weight Compass-safe distance Clearance to nearest obstruction 2.72 kg (6.0 lb.) 65 cm (25.6 in.) 9.5 cm (33/4 in.) Material Water rating Fuse Input voltage Polycarbonate plastic and die-cast aluminum IEC 60529 IPX71 6 A, 125 V fast-acting From 10 to 32 Vdc Max. power usage at 10 Vdc 36 W Typical current draw at 12 Vdc 2.5 A Max. current draw at 12 Vdc 3.0 A NMEA 2000 LEN @ 9 Vdc 2 NMEA 2000 Draw 75 mA max. Max. waypoints Max. routes 5,000 100 Max. active track points 50,000 points, 50 saved tracks Memory card Wireless frequency HTML integration 2 SD card slots; 32 GB max. card size 2.4 GHz @ 19.5 dBm nominal Compatible with OneHelm integration

(Plus models only) Typical current draw at 12 Vdc Sonar models: 35.9 W Non-sonar models: 1.08 A Sonar models: 1.18 A Max. current draw at 12 Vdc Non-sonar models: 1.45 A Sonar models: 2.96 A Temperature range From -15 to 55C (from 5 to 131F) Material Water rating Input voltage Fuse Polycarbonate plastic and die-cast aluminum IEC 60529 IPX7 1 From 10 to 32 Vdc 6 A, 125 V fast-acting NMEA 2000 LEN @ 9 Vdc 2 NMEA 2000 draw Max. waypoints Max. routes 75 mA max. 5,000 100 Max. active track points 50,000 points, 50 saved tracks Wireless frequency 2.4 GHz @ 17.6 dBm nominal Memory card 2 microSD card slots; 32 GB max. card size GPSMAP 9x3 Specifications Dimensions (W H D) 233.0 162.3 75.8 mm (9 3/16 6 3/8 3 in.) Clearance to next obstruction 33.2 mm (15/8 in.) Display size (W H) 198.7 111.8 mm (7 13/16 4 3/8 in.) 22.9 cm (9.0 in.) diagonal Display resolution WXGA, 1280 720 pixels Weight 1.6 kg (3.6 lb.) Max. power usage at 10 Vdc Non-sonar models: 22.0 W Typical current draw at 12 Vdc Sonar models: 40.2 W Non-sonar models: 1.34 A Sonar models: 1.37 A Max. current draw at 12 Vdc Non-sonar models: 1.78 A Sonar models: 3.20 A Temperature range From -15 to 55C (from 5 to 131F) Material Water rating Input voltage Fuse Polycarbonate plastic and die-cast aluminum IEC 60529 IPX7 1 From 10 to 32 Vdc 6 A, 125 V fast-acting NMEA 2000 LEN @ 9 Vdc 2 NMEA 2000 draw Max. waypoints Max. routes 75 mA max. 5,000 100 Max. active track points 50,000 points, 50 saved tracks Wireless frequency 2.4 GHz @ 17.6 dBm nominal Memory card 2 microSD card slots; 32 GB max. card size Temperature range From -15 to 55C (from 5 to 131F) Compass-safe distance 30 cm (11.81 in.) 1 The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. 1 The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. 68 Appendix GPSMAP 12x3 Specifications Dimensions (W H D) 308.3 227.6 81.8 mm (12 1/8 8 15/16 3 1/4 in.) Clearance to next obstruction 18.7 mm (3/4 in.) Display size (W H) 262.1 164.2 mm (10 15/16 6 7/16 in.) 30.7 cm (12.1 in.) diagonal Display resolution WXGA, 1280 800 pixels Weight 3.0 kg (6.6 lb.) Compass-safe distance 45 cm (17.72 in.) Max. power usage at 10 Vdc Non-sonar models: 26.5 W Typical current draw at 12 Vdc Sonar models: 43.0 W Non-sonar models: 1.67 A Sonar models: 1.68 A Max. current draw at 12 Vdc Non-sonar models: 2.15 A Sonar models: 3.56 A Temperature range From -15 to 55C (from 5 to 131F) Material Water rating Input voltage Fuse Polycarbonate plastic and die-cast aluminum IEC 60529 IPX7 1 From 10 to 32 Vdc 6 A, 125 V fast-acting NMEA 2000 LEN @ 9 Vdc 2 NMEA 2000 draw Max. waypoints Max. routes 75 mA max. 5,000 100 PGN Description 127250 Vessel heading 127258 Magnetic variance 127488 Engine parameters: Rapid update 127489 Engine parameters: Dynamic 127493 Transmission parameters: Dynamic 127505 Fluid level 127508 Battery status 128259 Speed: Water referenced 128267 Water depth 129025 Position: Rapid update 129026 COG and SOG: Rapid update 129029 GNSS position data 129283 Cross track error 129284 Navigation data 129539 GNSS DOPs 129540 GNSS satellites in view 130060 Label 130306 Wind data 130310 Environmental parameters (obsolete) 130311 Environmental parameters (obsolete) 130312 Temperature (obsolete) Max. active track points 50,000 points, 50 saved tracks Description Wireless frequency 2.4 GHz @ 17.6 dBm nominal Transmit and receive PGN list group function Memory card 2 microSD card slots; 32 GB max. card size Alert Response Trip parameters: Engine Traditional: 50/200, 77/200, 83/200 kHz Single Channel CHIRP: from 40 to 250 kHz Garmin ClearV CHIRP: 260/455/800 kHz Ultra High-Definition Garmin ClearV: 0.8 Mhz

(800 kHz), CHIRP range: 760 to 880 kHz Ultra High-Definition SideV: 1.2 MHz

(1,200 kHz), CHIRP range: 1,060 to 1,170 kHz CHIRP: 1000 W Garmin ClearV and SideV CHIRP: 500 W Sonar Models Specifications Specification Sonar frequencies2 Measurement Sonar transmit power

(RMS)3 Sonar depth4 5,000 ft. at 1 kW NMEA 2000 PGN Information Transmit and Receive PGN Description 059392 ISO acknowledgment 059904 ISO request 060928 ISO address claimed 065240 Commanded address 126208 Request group function 126996 Product information 126998 Configuration information 127237 Heading/track control 127245 Rudder 060160 ISO transport protocol: Data transfer 060416 ISO transport protocol: Connection management 1 The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. 2 Dependent upon the transducer. 3 Dependent upon the transducer rating and depth. 4 Dependent upon the transducer, water salinity, bottom type, and other water conditions. 065030 Generator average basic AC quantities (GAAC) Transmit PGN 126464 126984 127497 Receive PGN Description 126983 Alert 126985 Alert text 126987 Alert threshold 126988 Alert value 126992 System time 127251 Rate of turn 127257 Attitude 127498 Engine parameters: Static 127503 AC input status (obsolete) 127504 AC output status (obsolete) 127506 DC detailed status 127507 Charger status 127509 Inverter status 128000 Nautical leeway angle 128275 Distance log 129038 AIS class A position report 129039 AIS class B position report 129040 AIS class B extended position report 129044 Datum 129285 Navigation: Route, waypoint information 129794 AIS class A static and voyage related data 129798 AIS SAR aircraft position report 129799 Radio frequency/mode/power 129802 AIS safety-related broadcast message 129808 DSC call Information 129809 AIS class B "CS" static data report, part A 129810 AIS class B "CS" static data report, part B Appendix 69 Description Active diagnostic trouble codes Vehicle distance Water in fuel indicator Engine wait to start lamp Engine over speed test Engine air shutoff command status Engine alarm output command status Engine total hours of operation Navigation-based vehicle speed Engine fuel temperature 1 Engine oil temperature 1 Engine fuel delivery pressure Engine oil pressure Engine coolant pressure Engine coolant temperature Engine coolant level Engine fuel rate Engine average fuel economy Engine intake manifold #1 pressure Battery potential / power input 1 Transmission oil temperature Transmission oil pressure Fuel level Engine oil filter differential pressure PGN SPN 65226 65248 65279 65252 1081 65252 2812 65252 2813 65252 2814 65253 247 65256 517 65262 174 65262 175 65263 94 65263 100 65263 109 65263 110 65263 111 65266 183 65266 185 65270 102 65271 168 65272 177 65272 127 65276 96 65276 969 PGN Description 130313 Humidity 130314 Actual pressure 130576 Trim tab status 130577 Direction data 130316 Temperature: Extended range NMEA 0183 Information Transmit Sentence Description GPAPB APB: Heading or track controller (autopilot) sentence "B"

GPBOD BOD: Bearing (origin to destination) GPBWC BWC: Bearing and distance to waypoint GPGGA GGA: Global positioning system fix data GPGLL GLL: Geographic position (latitude and longitude) GPGSA GSA: GNSS DOP and active satellites GPGSV GSV: GNSS satellites in view GPRMB RMB: Recommended minimum navigation information GPRMC RMC: Recommended minimum specific GNSS data GPRTE RTE: Routes GPVTG VTG: Course over ground and ground speed GPWPL WPL: Waypoint location GPXTE XTE: Cross track error PGRME E: Estimated error PGRMM M: Map datum PGRMZ Z: Altitude SDDBT SDDPT DPT: Depth DBT: Depth below transducer SDMTW MTW: Water temperature SDVHW VHW: Water speed and heading Receive Sentence Description DPT DBT MTW VHW WPL DSC DSE HDG HDM MWD MDA MWV VDM Depth Depth below transducer Water temperature Water speed and heading Waypoint location Digital selective calling information Expanded digital selective calling Heading, deviation, and variation Heading, magnetic Wind direction and speed Meteorological composite Wind speed and angle AIS VHF data-link message You can purchase complete information about National Marine Electronics Association (NMEA) format and sentences from www.nmea.org. J1939 Information The chartplotter can receive J1939 sentences. The chartplotter cannot transmit over the J1939 network. Description Engine speed Engine percent load at current speed PGN SPN 61443 92 61444 190 Engine manifold exhaust gas temperature - right manifold 65031 2433 Engine manifold exhaust gas temperature - left manifold 65031 2434 Engine auxiliary coolant 65172 70 Appendix Index A ActiveCaptain6, 64 quickdraw16 smart notifications6, 7 updating charts7 updating software7 aerial photos11 AIS1114 alarms22, 61 ATONs12 distress signal device12 radar37 SART12 targeting11, 12 threats12, 37 turning on63 anchor drag61 arrival61 collision12, 63 deep water30, 61 engine46 fuel47, 62 gauges46 navigation61 off course61 shallow water30, 61 sonar30, 61 water temperature30, 61 weather62 AM51 anchor61 anchor drag alarm61 animated currents, tides10 antenna, GPS3 arrival alarm61 Auto Guidance17, 20, 60 paths20 shoreline distance21, 60 autopilot3942 adjusting the heading40 circles pattern41 cloverleaf pattern41 engaging40 orbit pattern41 pattern steering41 reducing rudder activity40 search pattern41 Shadow Drive40 steering increment40 steering patterns41 u-turn pattern41 Williamson turn pattern41 zigzag pattern41 autopilot.42 B back view1 background4 backlight5, 8 battery, management48 boundaries copying64 linking to SmartMode layout22 showing14 boundary line22, 23 boundary lines22 buoy reports55 C camera58 configuration56 controlling5658 home position56 pausing56 standby56 celestial information50 Index chart layers13, 14 settings13, 14 charts9, 11, 14, 15 appearance1315 details9 fishing9 layers13, 14 measuring distance9 navigation911 quickdraw15, 16 radar15 settings13 symbols9 updating7, 65 circuits49 clock61 alarm61 collision alarm12, 63 color mode5 combinations5 compass data bar5 rose13 connectors1 courses17 current stations50 indicators11 D DAB51, 52 data backup64 copying64 management64 deleting, all user data23 depth log48 depth shading13, 14 destinations navigation chart17 selecting17 detailed maps64 device cleaning66 registration65 digital selective calling44, 45 channels45 contacts44 individual routine call45 turning on44, 63 digital switching49 distress call44, 45 distress signal device12 DSC. See digital selective calling E EBL37 measuring37 showing37 EGNOS59 engine46, 47 alerts46 conditions46 engine gauges45, 46 configuring46 status alarms46 EPIRB12 event log59 F factory settings63 stations5 favorites4 Fish Eye 3D10 sonar cone15 suspended targets15 tracks15 fishfinder. See sonar fishing chart9, 55 FM51 Force trolling motor43, 44 fuel capacity47 fuel gauges4547 status alarm47, 62 synchronizing with actual fuel47 Fusion PartyBus51 G Garmin ClearV25 Garmin Express64, 65 updating charts65 Garmin Marine Network61 Garmin product support. See product support gauges4547 engine45, 46 fuel45, 47 limits46 status alarms46 trip48 wind48 GLONASS59 Go To17, 18 GPS67 EGNOS59 GLONASS59 signals3 source3 WAAS59 GPS accuracy61 graphs air temperature48 atmospheric pressure48 configuring48 depth48 water temperature48 wind angle48 wind speed48 GRID66 GRID pairing59, 66 gybing. See tacking and gybing H heading40 adjusting40 heading hold24 holding40 line13, 25 Shadow Drive40 help. See product support home screen3 customizing4, 5 I images4, 66 inReach48 messages49 J jibing. See tacking and gybing joystick66 K keel offset24, 62 keyboard59 L language59 locking, screen2 M man overboard18, 41, 45 manual viewer2 maps15, 64. See charts marine services17 mark location18 MARPA acquiring36 navigation chart14 tagged object37 targeting36 threats12, 37 71 clutter38, 39 color scheme39 custom park position39 echo trails37 field of view39 front-of-boat offset39 gain37, 38 guard zone36 MARPA12 optimizing display38 overlay15 overlay screen35 range35, 36 range rings39 source39 timed transmit35 transmitting35 waypoints39 radar overlay35 radio51 AM51 FM51 SiriusXM52, 53 range rings13 registering the device65 remote control8, 41, 42 disconnecting8 reset63 resetting settings53 station layouts5 restore63 Route To17 routes17, 19, 22 copying64 creating19, 20 deleting20 editing19 navigating19 navigating parallel to19 viewing list of19 waypoints64 S safe depth60 safe height60 safe-zone collision alarm12, 63 sailboat5, 23 sailing13, 23, 41 race timer23 starting line23 sailing gauges48 sailingstarting line23 SART12 satellite imagery11 satellite signals, acquiring3 screen brightness5 locking2, 6 unlocking2 screenshots67 capturing67 settings16, 59, 60 radar display39 system information59 Shadow Drive, enabling40 sharing data64 shoreline distance21, 60 shortcuts44 SideV26 SiriusXM51, 53 parental controls53 Satellite Radio52 messages48 MOB, device12 music player50, 52, 53. See media player measuring distance26 charts9 media player5053 alphabetical search51 DAB52 device name53 FUSION-Link50 muting51 preset51, 52, 56 radio52, 53 repeating51 shuffling51 SiriusXM Satellite Radio52 source51 stereo51 tuner region51, 52 tuning mode51 VHF51 zones51 memory card2, 64 detailed maps64 installing3 slot1 N navaids10 naviads12 navigation alarms61 navigation chart9, 11, 17, 55 ATONs12 marine service points17 MARPA14 radar overlay35 vessel trails14, 45 navigation inset5 NMEA 018344, 60 NMEA 200044, 61 notifications6, 7 O off6 off course alarm61 offset, front of boat39 Optimus49 Optimus Optimus49 other vessels AIS14 trails14 overlay bar43 overlay numbers5 P Panoptix34 Perspective 3D55 photos, aerial11 ports1 position, tracking45 position report45 power key1, 2, 5, 6 powerboat5, 23 preferred data source39, 40 premium charts10, 11 aerial photos11 Fish Eye 3D10, 15 tide and current indicators10 presets5, 51, 52 DAB52 product registration65 product support2, 67 Q quickdraw16 R radar3537, 39 AIS37 averaging38 bird mode37 72 sonar25, 28, 31 a-scope30, 31 alarms30, 61 appearance30 bottom lock29 color gain28 color rejection30 cone15 depth29 depth scale30 frequencies31 FrontV27 gain28 Garmin ClearV25 interference30 measuring distances26 noise28 numbers5 Panoptix26, 27, 32, 33 Panoptix LiveScope28, 34 perspective28 picture advance30 recording29 scroll speed29, 33 sharing28 SideV26 source28 surface noise30 suspended targets30 views25 waypoint28 zoom29 SOS18, 45 stations3 changing the station59 customizing the home screen of4 ordering the displays59 restoring the layout5, 59 support. See product support suspended targets15 symbols11 system information59, 64 T tacking and gybing24, 25 heading hold24 wind hold24 tank level sensors47 targeting36 temperature log48 tide stations10, 50 indicators11 touchscreen1, 2 tracks21, 22 clearing22 copying64 deleting22 editing21 list21 navigating21, 22 recording22 saving21 saving as route21 showing14, 21 transducer25, 28, 31, 34 trip gauges48 trolling motor43 bow offset44 compass44 troubleshooting67 U unit ID59 units of measure59 unlocking, screen2 updates, software65, 66 updating charts7 software7 user data, deleting23 SiriusXM Satellite Radio5153 smart notifications6, 7 SmartMode layout, linking to boundary22 software updates53, 66 updating7, 65, 66 Index V vessel trails14, 45 VHF radio44 calling an AIS target45 distress calls44, 45 DSC channel45 individual routine call45 video5558 configuring56, 57 source56 viewing56 VIRB camera58 voltage61 VRM37 measuring37 showing37 W WAAS59 warning manager50 messages50 watch, marine41 water speed63 temperature log48 temperature offset62 waypoints18, 67 copying64 creating9, 18 deleting19 editing18 man overboard18 navigating to18 projecting18 showing14 sonar28 tracked vessel45 viewing list of18 weather53, 54 alarms62 broadcasts53 charts14, 54 fishing54 forecast5355 overlay55 precipitation54 sea conditions54, 55 subscription53, 55 surface pressure55 visibility55 water temperature55 wave information55 winds54 WiFi6 WiFi technology8 wind, rose13 wind angle graph48 wind gauges48 wind hold24 adjusting24 wind sensor8 wind speed graph48 wireless devices7, 8, 48, 57, 58 connecting a wireless device8, 9 connecting to a wireless device6 network configuration8 Z zoom chart9 sonar29 Index 73 support.garmin.com October 2020 190-02141-10_0H

 

 

3 2 2 Important Safety and Product Information Informations importantes sur le produit et la scurit guida Informazioni importanti sulla sicurezza e sul prodotto Wichtige Sicherheits- und Produktinformationen 4 Informacin importante sobre el producto y tu seguridad 5 Informaes importantes sobre segurana e sobre o produto 6 Belangrijke veiligheids- en productinformatie Vigtige produkt- og sikkerhedinformationer 8 7 Trkeit turvallisuus- ja tuotetietoja Viktig sikkerhets- og produktinformasjon Guiden Viktig skerhets- och produktinformation Wane informacje dotyczce bezpieczestwa i produktu Dleit bezpenostn informace a informace o produktu Vane informacije o proizvodu i sigurnosti 8 9 10 10 11 12 13 14 14 20132017 Garmin Ltd. or its subsidiaries Printed in Taiwan April 2017 190-00720-32_0F IMPORTANT SAFETY AND PRODUCT INFORMATION WARNING Failure to heed the following warnings could result in an accident or collision resulting in death or serious injury. Marine Operation Warnings You are responsible for the safe and prudent operation of your vessel. This device is a tool that will enhance your capability to operate your vessel. This device does not relieve you from the responsibility of safely operating your vessel. Avoid navigational hazards and never leave the helm unattended. Use this device only as a navigational aid. Do not attempt to use the device for any purpose requiring precise measurement of direction, distance, location, or topography. Always be prepared to promptly regain control of the vessel. Use caution near hazards in the water, such as docks, pilings and other vessels. If the device has navigating capabilities, when navigating, carefully compare information displayed on the device to all available navigation sources, including information from visual sightings, local waterway rules and restrictions, and maps. For safety, always resolve any discrepancies or questions before continuing navigation. If the device uses maps, use the electronic chart in the device only to facilitate, not to replace, the use of authorized government charts. Official government charts and notices to mariners contain all information needed to navigate safely. If the device provides depth data, it should not be used as the primary means of preventing grounding or collision. Supplement depth data readings with information from applicable paper charts and visual indicators. Always operate the vessel at slow speeds if you suspect shallow water or submerged objects. Failure to heed this warning could lead to vessel damage or personal injury. If the device has video input capabilities, do not attempt to operate or watch video input while operating or navigating your vessel. Operating or watching the video input while the vessel is moving could cause an accident or collision resulting in property damage, serious injury, or death. Hearing Damage Warning Listening to the stereo at high volume can cause damage to your hearing. NOTICE Failure to heed the following notice could result in personal or property damage, or negatively impact the device functionality. Battery Notice Contact your local waste disposal department to dispose of the device/batteries in accordance with applicable local laws and regulations. GPS Notice The navigation device may experience degraded performance if you use it in proximity to any device that uses a terrestrial broadband network operating close to the frequencies used by any Global Navigation Satellite System (GNSS), such as the Global Positioning Service (GPS). Use of such devices may impair reception of GNSS signals. Product Environmental Programs Information about the Garmin product recycling program and WEEE, RoHS, REACH, and other compliance programs can be found at www.garmin.com/aboutGarmin/environment. Declaration of Conformity Hereby, Garmin declares that this product is in compliance with the Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

www.garmin.com/compliance. Innovation, Science and Economic Development Canada Compliance This device complies with Innovation, Science and Economic Development Canada license-

exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency Radiation Exposure This device is a mobile transmitter and receiver that uses an internal antenna to send and receive low levels of radio frequency (RF) energy for data communications. The device emits RF energy below the published limits when operating in its maximum output power mode and when used with Garmin authorized accessories. To comply with RF exposure compliance requirements, the device should be installed and operated with a minimum of 20 cm (7.87 in.) between the device and your body. The device should not be used in other configurations. This device must not be co-located or operated in conjunction with any other transmitter or antenna. FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet that is on a different circuit from the GPS device. Consult the dealer or an experienced radio/TV technician for help. This product does not contain any user-serviceable parts. Repairs should only be made by an authorized Garmin service center. Unauthorized repairs or modifications could result in permanent damage to the equipment, and void your warranty and your authority to operate this device under Part 15 regulations. Map Data Information Garmin uses a combination of governmental and private data sources. Virtually all data sources contain some inaccurate or incomplete data. In some countries, complete and accurate map information is either not available or is prohibitively expensive. Software License Agreement BY USING THE DEVICE, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY. Garmin Ltd. and its subsidiaries (Garmin) grant you a limited license to use the software embedded in this device (the Software) in binary executable form in the normal operation of the product. Title, ownership rights, and intellectual property rights in and to the Software remain in Garmin and/or its third-party providers. You acknowledge that the Software is the property of Garmin and/or its third-party providers and is protected under the United States of America copyright laws and international copyright treaties. You further acknowledge that the structure, organization, and code of the Software, for which source code is not provided, are valuable trade secrets of Garmin and/or its third-party providers and that the Software in source code form remains a valuable trade secret of Garmin and/or its third-party providers. You agree not to decompile, disassemble, modify, reverse Increase the separation between the equipment and the receiver. 2 assemble, reverse engineer, or reduce to human readable form the Software or any part thereof or create any derivative works based on the Software. You agree not to export or re-export the Software to any country in violation of the export control laws of the United States of America or the export control laws of any other applicable country. Limited Warranty THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER LEGAL RIGHTS, WHICH VARY FROM STATE TO STATE (OR BY COUNTRY OR PROVINCE). GARMIN DOES NOT EXCLUDE, LIMIT OR SUSPEND OTHER LEGAL RIGHTS YOU MAY HAVE UNDER THE LAWS OF YOUR STATE (OR COUNTRY OR PROVINCE). FOR A FULL UNDERSTANDING OF YOUR RIGHTS YOU SHOULD CONSULT THE LAWS OF YOUR STATE, COUNTRY OR PROVINCE. Non-aviation products are warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will, at its sole option, repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. This Limited Warranty does not apply to: (i) cosmetic damage, such as scratches, nicks and dents; (ii) consumable parts, such as batteries, unless product damage has occurred due to a defect in materials or workmanship; (iii) damage caused by accident, abuse, misuse, water, flood, fire, or other acts of nature or external causes; (iv) damage caused by service performed by anyone who is not an authorized service provider of Garmin; (v) damage to a product that has been modified or altered without the written permission of Garmin, or (vi) damage to a product that has been connected to power and/or data cables that are not supplied by Garmin. In addition, Garmin reserves the right to refuse warranty claims against products or services that are obtained and/or used in contravention of the laws of any country. Garmin navigation products are intended to be used only as a travel aid and must not be used for any purpose requiring precise measurement of direction, distance, location or topography. Garmin makes no warranty as to the accuracy or completeness of map data. This Limited Warranty also does not apply to, and Garmin is not responsible for, any degradation in the performance of any Garmin navigation product resulting from its use in proximity to any handset or other device that utilizes a terrestrial broadband network operating on frequencies that are close to the frequencies used by any Global Navigation Satellite System (GNSS) such as the Global Positioning Service (GPS). Use of such devices may impair reception of GNSS signals. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE WARRANTIES AND REMEDIES CONTAINED IN THIS LIMITED WARRANTY ARE EXCLUSIVE AND IN LIEU OF, AND GARMIN EXPRESSLY DISCLAIMS, ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY REMEDY OR OTHERWISE. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER LEGAL RIGHTS, WHICH VARY FROM STATE TO STATE AND FROM COUNTRY TO COUNTRY. IF IMPLIED WARRANTIES CANNOT BE DISCLAIMED UNDER THE LAWS OF YOUR STATE OR COUNTRY, THEN SUCH WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY. SOME STATES (AND COUNTRIES AND PROVINCES) DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. IN NO EVENT SHALL GARMIN BE LIABLE IN A CLAIM FOR BREACH OF WARRANTY FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. SOME STATES (AND COUNTRIES AND PROVINCES) DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. If during the warranty period you submit a claim for warranty service in accordance with this Limited Warranty, then Garmin will, at its option: (i) repair the device using new parts or previously used parts that satisfy Garmin's quality standards, (ii) replace the device with a new device or a refurbished device that meets Garmin's quality standards, or (iii) exchange the device for a full refund of your purchase price. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. Repaired or replaced devices have a 90 day warranty. If the unit sent in is still under its original warranty, then the new warranty is 90 days or to the end of the original 1 year warranty, whichever is longer. Before seeking warranty service, please access and review the online help resources available on support.garmin.com. If your device is still not functioning properly after making use of these resources, contact a Garmin Authorized service facility in the original country of purchase or follow the instructions on support.garmin.com to obtain warranty service. If you are in the United States, you can also call 1-800-800-1020. If you seek warranty service outside of the original country of purchase, Garmin cannot guarantee that the parts and products needed to repair or replace your product will be available due to differences in product offerings and applicable standards, laws and regulations. In that case, Garmin may, in its sole discretion and subject to applicable laws, repair or replace your product with comparable Garmin products and parts, or require you to ship your product to a Garmin Authorized service facility in the country of original purchase or to a Garmin Authorized service facility in another country that can service your product, in which case you will be responsible for complying with all applicable import and export laws and regulations and for paying all custom duties, V.A.T., shipping fees and other associated taxes and charges. In some cases, Garmin and its dealers may be unable to service your product in a country outside of the original country of purchase or return a repaired or replaced product to you in that country due to applicable standards, laws or regulations in that country. Online Auction Purchases: Products purchased through online auctions are not eligible for rebates or other special offers from Garmin warranty coverage. Online auction confirmations are not accepted for warranty verification. To obtain warranty service, an original or copy of the sales receipt from the original retailer is required. Garmin will not replace missing components from any package purchased through an online auction. International Purchases: A separate warranty may be provided by international distributors for devices purchased outside the United States depending on the country. If applicable, this warranty is provided by the local in-country distributor and this distributor provides local service for your device. Distributor warranties are only valid in the area of intended distribution. Marine Warranty Policy: Certain Garmin Marine products in certain areas have a longer warranty period and additional terms and conditions. Go to www.garmin.com/support/warranty _marine for more details and to see if your product is covered under the Garmin Marine Warranty Policy. Australian Purchases: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits under our Limited Warranty are in addition to other rights and remedies under applicable law in relation to the products. Garmin Australasia, 30 Clay Place, Eastern Creek, NSW 2766, Australia. Phone: 1800 235 822. INFORMATIONS IMPORTANTES SUR LE PRODUIT ET LA SCURIT Si vous ne respectez pas les avertissements suivants, vous risquez un accident ou une collision pouvant entraner des blessures graves, voire mortelles. AVERTISSEMENT Avertissements d'utilisation en milieu marin Vous tes responsable de l'utilisation sre et prudente de votre bateau. Cet appareil est un outil qui optimisera votre capacit de pilotage. Cet appareil ne vous dgage pas de vos responsabilits en cas de non-respect de la scurit bord. Evitez tout danger de navigation et ne relchez pas votre surveillance de la barre. L'appareil doit tre utilis uniquement comme une aide la navigation. Ne tentez pas d'utiliser l'appareil des fins exigeant une mesure prcise de l'orientation, de la distance, de la position ou de la topographie. Soyez toujours prt reprendre les commandes du navire. Soyez vigilant proximit des points dangereux, tels que les quais et les autres navires. En cours de navigation, et si l'appareil dispose de fonctions de navigation, comparez attentivement les informations affiches par l'appareil toutes les autres sources d'information disponibles, notamment les repres visuels, les rgles et restrictions locales relatives aux voies navigables, ainsi que les cartes. Pour votre scurit, cherchez rsoudre tout dysfonctionnement ou problme avant de poursuivre la navigation. Si l'appareil utilise des cartes, utilisez la carte lectronique de l'appareil uniquement pour faciliter l'usage de cartes gouvernementales officielles, pas pour les remplacer. Seules les cartes gouvernementales officielles et les avis aux navigateurs contiennent toutes les informations ncessaires une navigation en toute scurit. Si l'appareil fournit des donnes de profondeur, celles-ci ne doivent pas tre utilises en premier recours afin d'viter les risques d'chouage ou de collision. Compltez les mesures des donnes de profondeur l'aide d'informations issues de cartes papier et d'indicateurs visuels applicables. Si vous suspectez la prsence d'un haut-fond ou d'objets immergs, naviguez toujours faible vitesse. Si vous ignorez cet avertissement, votre bateau risque d'tre endommag ou vous risquez d'tre bless. Si l'appareil dispose de fonctions d'entre vido, n'utilisez pas l'entre vido en cours de navigation. Le visionnage de la vido lorsque le navire se dplace peut engendrer un accident ou une collision provoquant des dommages matriels et des blessures graves, voire mortelles. Avertissement concernant la perte d'audition En coutant la stro un volume trop lev, vous risquez d'endommager votre audition. AVIS Si vous ignorez cette notice, vous risquez de vous blesser, d'endommager votre bien ou d'affecter ngativement les fonctionnalits de l'appareil. Avis concernant la batterie Contactez la dchetterie locale pour plus d'informations sur la mise au rebut de l'appareil ou des batteries dans le respect des lois et rglementations locales applicables. Avertissement concernant le GPS Les performances de l'appareil de navigation peuvent tre rduites si vous utilisez l'appareil proximit d'un autre appareil utilisant un rseau terrestre large bande fonctionnant sur des frquences proches de celles utilises par les systmes de positionnement par satellites

(GNSS), comme le GPS. L'utilisation de tels appareils peut altrer la rception des signaux GNSS. Programmes environnementaux Des informations relatives au programme Garmin de recyclage des produits ainsi qu'aux directives DEEE et RoHS, la rglementation REACH et aux autres programmes de conformit sont disponibles l'adresse www.garmin.com/aboutGarmin/environment. Dclaration de conformit Par la prsente, Garmin dclare que son produit est conforme la Directive 2014/53/EU. Le texte de la dclaration de conformit UE dans sa version intgrale est disponible sur la page Web suivante : www.garmin.com/compliance. Innovation, Sciences et Dveloppement conomique Canada Conformit Cet appareil est conforme aux normes RSS sans licence du ministre Innovation, Sciences et Dveloppement conomique Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) ce priphrique ne doit pas causer d'interfrences et (2) doit accepter toute interfrence, y compris les interfrences pouvant entraner un fonctionnement indsirable de l'appareil. Exposition aux rayonnements frquence radiolectrique Cet appareil est un transmetteur/rcepteur mobile qui utilise une antenne interne pour envoyer et recevoir des champs de radiofrquences de faible puissance lors des communications de donnes. Les champs de radiofrquences mis par l'appareil lorsqu'il fonctionne au maximum de sa puissance et qu'il est utilis avec des accessoires approuvs par Garmin ne dpassent pas les limites fixes par la rglementation. Pour tre conforme aux exigences d'exposition aux radiofrquences, l'appareil doit tre install et utilis en respectant une distance minimale de 20 cm (7,87) entre l'appareil et votre corps. L'appareil ne doit tre utilis dans aucune autre configuration. Cet appareil ne doit pas tre plac ou utilis en conjonction avec d'autres antennes ou metteurs. Informations sur les donnes cartographiques Les donnes de Garmin proviennent la fois de sources publiques et prives. La quasi-totalit des sources de donnes contient une part d'informations inexactes ou incompltes. Dans certains pays, des informations cartographiques compltes et exactes sont soit indisponibles, soit proposes un cot prohibitif. Contrat de licence du logiciel EN UTILISANT CE PRODUIT, VOUS RECONNAISSEZ ETRE LIE PAR LES TERMES DU PRESENT CONTRAT DE LICENCE DE LOGICIEL. LISEZ ATTENTIVEMENT CE CONTRAT DE LICENCE. Garmin Ltd. et ses filiales ( Garmin ) vous concdent une licence limite pour l'utilisation du logiciel intgr cet appareil (le Logiciel ) sous la forme d'un programme binaire excutable, dans le cadre du fonctionnement normal du produit. Tout titre, droit de proprit ou droit de proprit intellectuelle dans le Logiciel ou concernant le Logiciel est la proprit de Garmin et/ou de ses fournisseurs tiers. Vous reconnaissez que le Logiciel est la proprit de Garmin et/ou de ses fournisseurs tiers et qu'il est protg par les lois en vigueur aux Etats-Unis d'Amrique et par les traits internationaux relatifs aux droits d'auteur. Vous reconnaissez galement que la structure, l'organisation et le code du Logiciel, dont le code source n'est pas fourni, constituent d'importants secrets de fabrication de Garmin et/ou de ses fournisseurs tiers, et que le code source du Logiciel demeure un important secret de fabrication de Garmin et/ou de ses fournisseurs tiers. Vous acceptez de ne pas dcompiler, dsassembler, modifier, assembler rebours, tudier par rtro-ingnierie ou transcrire en langage humain intelligible le Logiciel ou toute partie du Logiciel, ou crer toute uvre drive du Logiciel. Vous acceptez de ne pas exporter ni de rexporter le Logiciel vers un pays contrevenant aux lois de contrle l'exportation des Etats-Unis d'Amrique ou celles de tout autre pays concern. Garantie limite LA PRSENTE GARANTIE VOUS OCTROIE DES DROITS PARTICULIERS ET VOUS BNFICIEZ PEUT-TRE D'AUTRES DROITS QUI PEUVENT VARIER D'UN TAT, PAYS, OU PROVINCE L'AUTRE. GARMIN N'EXCLUT PAS, NI NE LIMITE OU SUSPEND, LES AUTRES DROITS LGAUX DONT VOUS BNFICIEZ EN VERTU DU DROIT DE VOTRE TAT, PAYS OU PROVINCE. POUR BIEN COMPRENDRE VOS DROITS, CONSULTEZ LE DROIT APPLICABLE DANS VOTRE TAT, PAYS OU PROVINCE. Les produits non aronautiques sont garantis contre tout dfaut de matriel et de fabrication pendant un an compter de leur date d'achat. Durant cette priode, Garmin pourra, son entire discrtion, rparer ou remplacer tout composant qui s'avrerait dfectueux dans le cadre d'un usage normal. Ce type de rparation ou de remplacement ne sera pas factur au client, qu'il s'agisse des composants ou de la main-d'uvre, condition que le client prenne en charge les frais de port. La prsente garantie limite ne couvre pas : (i) les dommages esthtiques, tels que les raflures, les rayures et les bosses ; (ii) les consommables, comme les piles, moins que le dommage ne soit d un dfaut matriel ou de fabrication ; (iii) les dommages provoqus par un accident, une utilisation abusive, une mauvaise utilisation, l'eau, une inondation, un incendie ou toute autre catastrophe naturelle ou cause extrieure ; (iv) les dommages provoqus par des fournisseurs de services non agrs par Garmin ; ou (v) les dommages sur un produit ayant t modifi sans l'autorisation crite de Garmin ; ou (vi) les dommages sur un produit raccord des cbles d'alimentation et/ou des cbles de donnes non fournis par Garmin. En outre, Garmin se rserve le droit de refuser toute demande de service sous garantie relative un produit ou service obtenu et/ou utilis en violation des lois de tout pays.Les produits de navigation Garmin constituent uniquement une aide la navigation et ne doivent pas tre utiliss des fins exigeant l'valuation prcise de la direction, de la distance, de la position ou de la topographie. Garmin n'offre aucune garantie quant l'exactitude ou l'exhaustivit des donnes cartographiques. La prsente garantie limite ne couvre pas, et Garmin n'est pas responsable de, toute dgradation des performances d'un produit de navigation Garmin si celui-ci a t utilis prs d'un appareil portable ou de tout autre appareil utilisant un rseau terrestre large bande fonctionnant sur des frquences proches de celles utilises par tout systme de positionnement par satellites (GNSS), comme le GPS. L'utilisation de tels appareils peut altrer la rception des signaux GNSS. DANS LES LIMITES PRVUES PAR LA LOI, LES GARANTIES ET RECOURS CONTENUS DANS LA PRSENTE GARANTIE LIMITE SONT EXCLUSIFS ET REMPLACENT, ET GARMIN EXCLUT EXPLICITEMENT, TOUTE AUTRE GARANTIE ET RECOURS EXPRS, IMPLICITES, LGAUX OU AUTRES, Y COMPRIS, MAIS DE MANIRE NON LIMITATIVE, TOUTE GARANTIE IMPLICITE MARCHANDE OU D'ADQUATION UN USAGE PARTICULIER, TOUT RECOURS LGAL OU AUTRES. LA PRSENTE GARANTIE VOUS OCTROIE DES DROITS PARTICULIERS ET VOUS BNFICIEZ PEUT-TRE D'AUTRES DROITS QUI PEUVENT VARIER D'UN TAT OU PAYS UN AUTRE. SI LES GARANTIES IMPLICITES NE PEUVENT PAS TRE EXCLUES EN VERTU DU DROIT DE VOTRE TAT OU PAYS, ALORS LESDITES GARANTIES SONT LIMITES LA DURE DE LA PRSENTE GARANTIE LIMITE. CERTAINS TATS, PAYS ET PROVINCES INTERDISANT LA RESTRICTION DE LA DURE D'UNE GARANTIE IMPLICITE, LES RESTRICTIONS SUSMENTIONNES PEUVENT NE PAS VOUS CONCERNER. EN AUCUN CAS, LA SOCIT GARMIN NE SAURAIT TRE TENUE POUR RESPONSABLE EN CAS DE RUPTURE DE LA GARANTIE DE TOUT DOMMAGE ACCESSOIRE, SPCIAL, INDIRECT OU CONSCUTIF RSULTANT DE L'UTILISATION, DE LA MAUVAISE UTILISATION OU DE L'IMPOSSIBILIT D'UTILISER CE PRODUIT, OU RSULTANT DE DFAUTS DU PRODUIT. CERTAINS TATS, PAYS ET PROVINCES INTERDISANT L'EXCLUSION OU LA RESTRICTION DES DOMMAGES PARTICULIERS OU ACCESSOIRES, LES RESTRICTIONS SUSMENTIONNES PEUVENT NE PAS VOUS CONCERNER. Si, pendant la dure de la garantie, vous faites une demande de services de garantie conformment la prsente Garantie limite, Garmin peut, sa discrtion : (i) rparer l'appareil l'aide de pices neuves ou dj utilises, si celles-ci remplissent les critres de qualit de Garmin, (ii) remplacer l'appareil par un appareil neuf ou par un appareil remis neuf qui remplit les critres de qualit de Garmin ou (iii) rembourser l'appareil au prix o vous l'avez achet. CE TYPE DE RECOURS SERA VOTRE RECOURS UNIQUE ET EXCLUSIF POUR TOUTE RUPTURE DE GARANTIE. Les appareils rpars ou remplacs bnficient d'une garantie de 90 jours. Si l'unit envoye est toujours couverte par la garantie d'origine, cette nouvelle garantie dure 90 jours ou jusqu' la fin de la priode de garantie d'origine qui est d'un an ; la priode ayant la date de fin la plus loigne prvaut. Avant de demander des services de garantie, merci de consulter les ressources d'aide en ligne disponibles sur support.garmin.com. Si votre appareil ne fonctionne toujours pas correctement aprs avoir appliqu les consignes indiques en ligne, contactez un centre de service autoris par Garmin dans le pays o vous avez achet l'appareil ou suivez les instructions disponibles sur le site support.garmin.com pour obtenir des services de garantie. Si vous vous trouvez aux tats-Unis, vous pouvez aussi appeler le 1-800-800-1020. Si vous demandez des services de garantie en dehors du pays o vous avez achet l'appareil, Garmin ne peut pas garantir que les pices et produits ncessaires la rparation ou au remplacement de votre produit seront disponibles, car les offres, les normes, les lois et les rglementations diffrent selon les pays. Dans ce cas, Garmin peut, sa seule discrtion et conformment au droit applicable, rparer votre produit l'aide de pices comparables ou remplacer votre produit par un produit Garmin comparable, ou vous demander d'envoyer votre produit vers un centre de service autoris par Garmin dans le pays o vous avez achet le produit ou vers un centre de service autoris par Garmin d'un autre pays o votre produit pourra tre rpar ou remplac, et, dans ce cas, vous devrez respecter le droit et les rglementations en matire d'importation et d'exportation et vous acquitter seul des droits de douane, de la TVA, des frais d'expdition ainsi que de tous autres taxes et frais. Dans certains cas, Garmin et ses revendeurs ne peuvent ni rparer votre produit dans un autre pays que celui o vous avez achet le produit, ni envoyer un produit de remplacement neuf ou rpar dans ce pays, cause des normes, lois et rglementations du pays en question. Achats dans le cadre d'enchres en ligne : les produits achets au cours d'enchres en ligne ne peuvent faire l'objet de rabais ou d'autres offres spciales proposs par la garantie de Garmin. Les confirmations de vente aux enchres en ligne ne sont pas acceptes dans le cadre d'une vrification sous garantie. Pour bnficier d'un service sous garantie, l'original ou une copie de la facture dresse par le premier revendeur doit tre prsent. Garmin ne procdera aucun remplacement de composant manquant sur tout produit achet dans le cadre d'enchres en ligne. Achats internationaux : selon les pays, une garantie distincte peut tre accorde par les distributeurs internationaux pour les appareils achets hors des Etats-Unis. Le cas chant, cette garantie est fournie par le distributeur du pays d'achat et ledit distributeur prend en charge les services locaux ncessaires pour votre appareil. Les garanties distributeur sont valides uniquement dans les zones de distribution vises. Politique de garantie des produits marine : pour certains produits marine de Garmin de certaines rgions du monde, la priode de garantie est plus longue et des conditions supplmentaires s'appliquent. Rendez-vous sur le site www.garmin.com/support/warranty _marine pour plus de dtails et pour savoir si votre produit est couvert par la garantie des produits marine de Garmin. INFORMAZIONI IMPORTANTI SULLA SICUREZZA E SUL PRODOTTO AVVERTENZA Il mancato rispetto delle indicazioni fornite di seguito potrebbe causare incidenti e tamponamenti gravi o mortali. Avvertenze sull'uso in ambiente nautico Ogni utente responsabile della navigazione sicura della propria imbarcazione. Questo dispositivo costituisce un aiuto alla navigazione, che non esime l'utente dal navigare responsabilmente e con prudenza. Durante la navigazione, evitare le zone pericolose e non lasciare mai il timone. Utilizzare il dispositivo solo come ausilio alla navigazione. Non utilizzare il dispositivo per ottenere misurazioni precise della direzione, della distanza, della posizione o della topografia. 3 Tenersi sempre pronti a riprendere il controllo dell'imbarcazione in modo tempestivo. Prestare sempre attenzione durante l'uso del sistema, ma in particolar modo nelle vicinanze di moli, scogli ed altre imbarcazioni. Durante la navigazione verificare le informazioni del dispositivo con l'ambiente circostante, le carte ufficiali, le note ai naviganti, avvertenze e leggi in vigore. Per motivi di sicurezza, risolvere eventuali incongruenze o problemi prima di continuare la navigazione. La cartografia un ausilio alla navigazione e non sostituisce le carte governative autorizzate. Gli avvisi ai naviganti e le carte governative ufficiali contengono tutte le informazioni necessarie per una navigazione in sicurezza. I dati di profondit indicati dal dispositivo non devono essere utilizzati come unico strumento di misurazione. Integrare i dati di profondit del prodotto con le carte ufficiali. Mantenere sempre una velocit di crociera ridotta, se si ritiene di navigare in fondali bassi o si sospetta la presenza di oggetti sommersi. La mancata osservanza di tale avvertenza potrebbe provocare danni all'imbarcazione o alle persone. Se il prodotto dispone di ingressi video, non utilizzarli durante la navigazione. La visione di sorgenti video diverse dalle informazioni per la navigazione possono distrarre ed essere causa di incidenti o danni a cose e persone. Avvertenza relativa ai danni all'udito Ascoltare lo stereo ad alto volume pu causare danni all'udito. AVVISO Il mancato rispetto dell'avviso fornito di seguito potrebbe causare danni personali o alle propriet oppure incidere in modo negativo sulla funzionalit del dispositivo. Avviso sulla batteria Per un corretto smaltimento del dispositivo/batterie in conformit alle leggi e disposizioni locali, contattare le autorit locali preposte. Avviso GPS Le prestazioni del dispositivo di navigazione potrebbero ridursi in prossimit di un altro dispositivo che utilizza una rete a banda larga terrestre vicino alle frequenze utilizzate da un Global Navigation Satellite System (GNSS), ad esempio il Global Positioning Service (GPS). L'utilizzo di tali dispositivi potrebbe impedire la ricezione dei segnali GNSS. Programmi ambientali per i prodotti Le informazioni sul programma di riciclo dei prodotti Garmin, sulle direttive WEEE, RoHS, REACH e su altri programmi di conformit sono reperibili sul sito Web www.garmin.com

/aboutGarmin/environment. Dichiarazione di conformit Con il presente documento, Garmin dichiara che questo prodotto conforme alla Direttiva 2014/53/UE. Il testo completo della dichiarazione UE di conformit disponibile al seguente indirizzo Internet: www.garmin.com/compliance. Informazioni sui dati mappa Garmin utilizza una serie di fonti statali e private. Tutte le fonti di dati possono contenere dati imprecisi e incompleti. In alcuni paesi, le informazioni su mappe complete e precise non sono disponibili o sono proibitive in termini di costi. Contratto di licenza software L'USO DEL DISPOSITIVO IMPLICA L'ACCETTAZIONE DEI TERMINI E DELLE CONDIZIONI SPECIFICATI NEL SEGUENTE CONTRATTO DI LICENZA SOFTWARE. LEGGERE ATTENTAMENTE IL PRESENTE CONTRATTO. Garmin Ltd. e sue affiliate ("Garmin") concedono una licenza limitata per l'utilizzo del software integrato in questo dispositivo (il "Software") in forma binaria eseguibile per il normale funzionamento del prodotto. Il titolo, i diritti di propriet e di propriet intellettuale relativi al Software sono esclusivi di Garmin e/o dei rispettivi fornitori di terze parti. L'utente prende atto che il Software di propriet di Garmin e/o dei rispettivi fornitori di terze parti ed protetto dalle leggi sul copyright in vigore negli Stati Uniti d'America e dai trattati internazionali sul copyright. L'utente riconosce inoltre che la struttura, l'organizzazione e il codice del Software, di cui non viene fornito il codice sorgente, sono considerati segreti commerciali di Garmin e/o dei rispettivi fornitori di terze parti e che il Software in formato sorgente resta un segreto commerciale di Garmin e/o dei rispettivi fornitori di terze parti. L'utente accetta di non decompilare, disassemblare, modificare, decodificare o convertire in formato leggibile il Software o parte di esso n di creare altri prodotti basati sul Software. L'utente accetta di non esportare o riesportare il Software in qualsiasi Paese in violazione delle leggi sul controllo delle esportazioni in vigore negli Stati Uniti d'America o delle norme per il controllo delle esportazioni da qualsiasi altro Paese. Garanzia La garanzia prestata dal Venditore:

al Consumatore ossia, ai sensi dell'art. 3, D.Lgs. 6 ottobre 2005, alla "persona fisica che agisce per scopi estranei all'attivit imprenditoriale o professionale eventualmente svolta", sulla base della medesima norma istitutiva del cos detto Codice del consumo. In base a detta legge la durata della garanzia di 24 mesi decorrenti dalla data di consegna del prodotto al Consumatore. La garanzia copre solo i difetti di conformit o d'origine, cio preesistenti alla consegna del bene al Consumatore e non copre i difetti legati ad un'errata installazione o ad errato uso dello stesso;

al Professionista, ossia ai sensi del citato art. 3 206/05, alla "persona fisica o giuridica che agisce nell'esercizio della propria attivit imprenditoriale o professionale, ovvero un suo intermediario" nei limiti di quanto previsto dagli artt. 1490 ss c.c. e nei termini di cui all'art. 1495 c.c. Garanzia Prodotto Il Prodotto, a cui riferita la presente garanzia, garantito esente da difetti originari di conformit per un periodo di 24 mesi dalla data di consegna all'utente finale, conformemente a quanto previsto dal D.Lgs. 206/05. La preghiamo, prima di prendere possesso del prodotto, di verificare, assieme al Venditore, se il prodotto conforme alle Sue aspettative. Laddove il Venditore si occupi anche della installazione del Prodotto, La preghiamo, inoltre, di verificarne il corretto funzionamento, eventualmente eseguendo una prova d'uso reale. Procedura Qualora intenda avvalersi dei diritti di cui alle presenti condizioni di garanzia, la preghiamo di visitare il sito web di Garmin Italia (www.garmin.it) onde ottenere le informazioni circa l'esatta modalit di consegna o spedizione dei prodotti. Con le limitazioni specificate in seguito, e qualora sussistano le condizioni per riconoscere la garanzia ai sensi del D.Lgs. 206/05, il prodotto verr riparato senza nessun costo relativo alle spese strettamente necessarie per la riparazione e quindi rispedito in porto franco al Venditore. Resta fermo quanto disposto dall'art. 130, D.Lgs. 206/05 in particolare quanto all'oggettiva impossibilit o l'eccessiva onerosit della riparazione. Per i prodotti in garanzia il Consumatore nulla deve al Venditore a titolo di contributo spese di trasporto o di gestione. Laddove il prodotto dovesse essere inviato nonostante il periodo di garanzia sia scaduto ovvero risulti che trattasi di difetto non coperto dalla Garanzia, ovvero il prodotto sia privo di difetti, Garmin Italia addebiter al Venditore i costi del trasporto, amministrativi e tecnici sostenuti. Limiti nel caso di intervento in garanzia La garanzia di Garmin Italia non copre i difetti originari manifestatisi oltre il termine di durata della garanzia, i difetti che non preesistevano alla consegna del prodotto, i guasti derivanti da negligenza o trascuratezza nell'uso, da errata installazione o manutenzione, erroneo immagazzinaggio e/o conservazione, da manutenzione effettuata da personale non autorizzato, da danni di trasporto, corrosione o per strumenti in cui il numero di matricola sia stato in qualche 4 modo alterato o cancellato. Garmin Italia non pu essere ritenuta responsabile per danni causati durante l'installazione o come conseguenza di un'installazione scorretta. La presente Garanzia non copre i controlli periodici, gli allineamenti e le calibrazioni originarie e successive, prove in mare o su terra, o spiegazioni pratiche sull'uso del prodotto a meno che non siano specificatamente necessari per il ripristino funzionale della parte sostituita coperta dalla garanzia. La garanzia non copre altres difetti derivanti da incidenti, calamit naturali od altre cause fra le quali, a titolo meramente esemplificativo, pioggia, grandine o fulmini. La garanzia non copre i danni conseguenti a sovraccarichi di corrente dovuti alla rete cui il prodotto dovesse essere collegato o causati da altre apparecchiature, sistemi o componenti in occasione di impropria connessione o uso non autorizzato o permesso del prodotto ivi compreso nel caso di eventuale utilizzo di un caricabatteria di modello differente rispetto a quello fornito con il prodotto. I materiali soggetti ad usura (inclusi fusibili, batterie, cinghie, ventole o le parti meccaniche connesse) sono specificata-mente esclusi dalla presente Garanzia. L'eventuale rottura di sigilli o la precedente manomissione del prodotto escludono la possibilit di avvalersi della Garanzia. La presente Garanzia non copre le ore di lavoro straordinario. La Garanzia Garmin Italia non copre eventuali differenze di colorazione, di materiale o aspetto sussistenti tra quanto a titolo indicativo, illustrato nella pubblicit, nei cataloghi o su Internet, che non siano state oggetto di specifico reclamo al momento della consegna del prodotto. Tutti i prodotti Garmin Italia sono considerati ausili allo svolgimento dell'attivit a cui sono destinati. quindi esclusivamente responsabilit dell'utente usare la prudenza e il giudizio necessari durante il loro utilizzo. Garmin Italia non risponder dell'eventuale inosservanza delle normali regole di diligenza e prudenza ed altres, nel caso di utilizzo a bordo di autoveicoli, velivoli, natanti o di altri mezzi di trasporto non risponder della violazione delle norme, disposizioni delle autorit o regolamenti disciplinanti la loro circolazione e non risponder dei danni eventualmente causati a terzi ed alla persona del Consumatore. Assistenza oltre i termini di garanzia Qualora il prodotto in Suo possesso manifestasse problemi di funzionamento oltre i termini di garanzia, ovvero per quanto entro i 24 mesi di vita fosse stato danneggiato o abbisognasse comunque di interventi tecnici per cause che non rientrano fra quelle coperte dalla garanzia, La preghiamo di contattare telefonicamente il Customer Care Garmin al numero indicato sul sito www.garmin.it al fine di concordare la modalit di invio dello strumento per riparazione o verifica. Ricordiamo che in caso di assistenza fuori garanzia le spese di trasporto sono a carico del Consumatore, come pure i costi di riparazione, verifica, aggiornamento software o eventuale reset delle apparecchiature. WICHTIGE SICHERHEITS- UND PRODUKTINFORMATIONEN WARNUNG Falls Sie folgende Warnungen nicht beachten, knnte es zu einem Unfall oder Zusammensto mit schweren oder sogar tdlichen Verletzungen kommen. Warnungen zum Betrieb von Schiffen Sie sind fr den sicheren und umsichtigen Betrieb des Boots verantwortlich. Mit dem Gert knnen Sie die Mglichkeiten zur Steuerung des Boots erheblich erweitern. Das Gert befreit Sie nicht von der Verantwortung, fr einen sicheren Betrieb des Boots zu sorgen. Vermeiden Sie riskante Manver, und lassen Sie den Steuerstand niemals unbeaufsichtigt. Verwenden Sie dieses Gert lediglich als Navigationshilfe. Verwenden Sie das Gert nicht, um damit exakte Richtungs-, Entfernungs-, Positions- oder topografische Messungen durchzufhren. Seien Sie stets bereit, unverzglich die Steuerung des Boots zu bernehmen. Lassen Sie in der Nhe von Hindernissen im Wasser, z. B. Docks, Pfeilern und anderen Booten, Vorsicht walten. Wenn das Gert ber Navigationsfunktionen verfgt, vergleichen Sie beim Navigieren die auf dem Gert angezeigten Informationen sorgfltig mit allen anderen verfgbaren Navigationsquellen, z. B. visuellen Signalen, lokalen Bestimmungen und Einschrnkungen fr Schifffahrtswege sowie mit Karten. Aus Sicherheitsgrnden sollten Sie Unstimmigkeiten oder Fragen klren, bevor Sie die Fahrt fortsetzen. Wenn das Gert Karten nutzt, soll die elektronische Karte den Gebrauch von Karten offizieller staatlicher Stellen erleichtern, diese jedoch nicht ersetzen. Die Karten von offiziellen staatlichen Stellen und die nautischen Mitteilungen fr Seefahrer enthalten alle Informationen, die fr die sichere Navigation erforderlich sind. Wenn das Gert Tiefendaten bereitstellt, sollten diese nicht ausschlielich zur Vermeidung von Grundberhrung oder Zusammensten verwendet werden. Nutzen Sie zustzlich zu Tiefendatenangaben Informationen von entsprechenden Seekarten und visuellen Hinweisen. Betreiben Sie das Schiff stets bei niedrigen Geschwindigkeiten, falls Sie Bereiche mit Flachwasser oder Unterwasserobjekten vermuten. Die Nichteinhaltung dieser Warnung knnte zur Beschdigung des Schiffs oder zu Verletzungen fhren. Wenn das Gert ber Videoeingangsfunktionen verfgt, beachten Sie, dass whrend des Schiffsbetriebs oder der Schiffsnavigation keine Videoeingnge laufen oder angesehen werden drfen. Durch die Bedienung des Videoeingangs oder das Ansehen eines Videos whrend der Fahrt des Schiffes knnen Unflle oder Kollisionen und damit Sachschden, schwere oder sogar tdliche Verletzungen verursacht werden. Warnung zu Hrschden Wenn Sie mit hoher Lautstrke Radio hren, kann Ihr Gehr geschdigt werden. HINWEIS Die Nichteinhaltung des folgenden Hinweises kann zu Personen- oder Sachschden fhren oder die Funktionsweise des Gerts beeintrchtigen. Hinweis zum Akku Wenden Sie sich zur ordnungsgemen, im Einklang mit anwendbaren rtlichen Gesetzen und Bestimmungen stehenden Entsorgung von Gert und/oder Akku an die zustndige Abfallentsorgungsstelle. GPS-Hinweis Die Leistung des Navigationsgerts ist u. U. eingeschrnkt, wenn es in der Nhe von Gerten verwendet wird, die ein terrestrisches Breitbandnetz nutzen, dessen Frequenzen nahe der von einem GNSS (Global Navigation Satellite System) wie dem Global Positioning Service (GPS) verwendeten Frequenzen liegen. Die Verwendung dieser Gerte kann den Empfang von GNSS-

Signalen beeintrchtigen. Umweltschutzprogramme fr das Produkt Informationen zum Produktrecyclingprogramm von Garmin sowie zur WEEE-, RoHS- und REACH-Richtlinie und zu anderen Programmen zur Einhaltung von Richtlinien finden Sie unter www.garmin.com/aboutGarmin/environment. Konformittserklrung Garmin erklrt hiermit, dass dieses Produkt der Direktive 2014/53/EU entspricht. Der vollstndige Text der EU-Konformittserklrung ist unter folgender Internetadresse verfgbar:

www.garmin.com/compliance. Kartendaten-Informationen Garmin verwendet eine Kombination aus ffentlichen und privaten Datenquellen. Nahezu alle Datenquellen enthalten in bestimmtem Ausma ungenaue oder unvollstndige Daten. In einigen Lndern sind vollstndige und genaue Karteninformationen nicht erhltlich oder unverhltnismig teuer. Software-Lizenzvereinbarung DURCH DIE VERWENDUNG DES GERTS STIMMEN SIE DEN BEDINGUNGEN DER FOLGENDEN SOFTWARE-LIZENZVEREINBARUNG ZU. LESEN SIE DIE LIZENZVEREINBARUNG AUFMERKSAM DURCH. Garmin Ltd. und deren Tochtergesellschaften (Garmin) gewhren Ihnen im Rahmen des normalen Betriebs dieses Gerts eine beschrnkte Lizenz zur Verwendung der in diesem Gert im Binrformat integrierten Software (die Software). Verfgungsrechte, Eigentumsrechte und Rechte am geistigen Eigentum an der Software verbleiben bei Garmin und/oder deren Drittanbietern. Sie erkennen an, dass die Software Eigentum von Garmin und/oder dessen Drittanbietern ist und durch die Urheberrechte der Vereinigten Staaten von Amerika und internationale Urheberrechtsabkommen geschtzt ist. Weiterhin erkennen Sie an, dass Struktur, Organisation und Code der Software, fr die kein Quellcode zur Verfgung gestellt wird, wertvolle Betriebsgeheimnisse von Garmin und/oder dessen Drittanbietern sind und dass der Quellcode der Software ein wertvolles Betriebsgeheimnis von Garmin und/oder deren Drittanbietern bleibt. Sie verpflichten sich, die Software oder Teile davon nicht zu dekompilieren, zu deassemblieren, zu verndern, zurckzuassemblieren, zurckzuentwickeln, in eine allgemein lesbare Form umzuwandeln oder ein von der Software abgeleitetes Werk zu erstellen. Sie verpflichten sich, die Software nicht in ein Land zu exportieren oder zu reexportieren, das nicht im Einklang mit den Exportkontrollgesetzen der Vereinigten Staaten von Amerika oder den Exportkontrollgesetzen eines anderen, in diesem Zusammenhang relevanten Landes steht. Eingeschrnkte Gewhrleistung DIESE EINGESCHRNKTE GEWHRLEISTUNG GEWHRT IHNEN BESTIMMTE GESETZLICHE RECHTE; AUSSERDEM HABEN SIE GGF. ANDERE GESETZLICHE RECHTE, DIE JE NACH BUNDESLAND (BZW. LAND ODER PROVINZ) VARIIEREN. GARMIN SCHRNKT ANDERE GESETZLICHE RECHTE, DIE IHNEN GEMSS DEN GESETZEN IHRES BUNDESLANDES (BZW. IHRES LANDES ODER IHRER PROVINZ) U. U. ZUSTEHEN, NICHT EIN, UND SETZT DIESE AUCH NICHT AUS. DIE GESETZE IHRES BUNDESLANDES, IHRES LANDES ODER IHRER PROVINZ BIETEN IHNEN EINEN VOLLSTNDIGEN EINBLICK IN IHRE RECHTE. Fr nicht fr die Luftfahrt vorgesehenen Produkte gilt ab dem Kaufdatum eine einjhrige Garantie auf Material- und Verarbeitungsfehler. Innerhalb dieses Zeitraums repariert oder ersetzt Garmin nach eigenem Ermessen alle bei ordnungsgemer Verwendung ausgefallenen Komponenten. Diese Reparatur- und Austauscharbeiten sind fr den Kunden in Bezug auf Teile und Arbeitszeit unter der Voraussetzung kostenlos, dass dieser die Transportkosten bernimmt. Diese eingeschrnkte Gewhrleistung findet keinerlei Anwendung auf: (i) kosmetische Schden, z. B. Kratzer oder Dellen, (ii) Verschleiteile wie Batterien, sofern Produktschden nicht auf Material- oder Verarbeitungsfehler zurckzufhren sind, (iii) durch Unflle, Missbrauch, unsachgeme Verwendung, Wasser, berschwemmung, Feuer oder andere hhere Gewalt oder uere Ursachen hervorgerufene Schden, (iv) Schden aufgrund einer Wartung durch nicht von Garmin autorisierte Dienstanbieter, (v) Schden an einem Produkt, das ohne die ausdrckliche schriftliche Genehmigung von Garmin modifiziert oder gendert wurde, oder (vi) Schden an einem Produkt, das mit Netz- und/oder Datenkabeln verbunden wurde, die nicht von Garmin bereitgestellt wurden. Darber hinaus behlt Garmin sich das Recht vor, Garantieansprche fr Produkte oder Dienstleistungen abzulehnen, die unter Versto gegen die Gesetze eines Landes erworben und/oder verwendet werden.Navigationsprodukte von Garmin sind ausschlielich als Navigationshilfe vorgesehen und drfen nicht fr Zwecke verwendet werden, die przise Messungen von Richtungen, Distanzen, Positionen oder Topografien erfordern. Garmin bernimmt keinerlei Gewhrleistungen im Hinblick auf die Richtigkeit oder Vollstndigkeit der Kartendaten. Auerdem findet diese eingeschrnkte Gewhrleistung keinerlei Anwendung auf Leistungseinschrnkungen eines Navigationsprodukts von Garmin, die sich durch die Verwendung des Gerts in der Nhe von Telefonen oder anderen Gerten ergeben, die ein terrestrisches Breitbandnetz nutzen, dessen Frequenzen nahe der von einem GNSS (Global Navigation Satellite System) wie dem Global Positioning Service (GPS) verwendeten Frequenzen liegen, noch ist Garmin fr diese Leistungseinschrnkungen verantwortlich. Die Verwendung dieser Gerte kann den Empfang von GNSS-Signalen beeintrchtigen. IM NACH GELTENDEN RECHT MAXIMAL ZULSSIGEN UMFANG GELTEN DIE IN DIESER EINGESCHRNKTEN GEWHRLEISTUNG AUFGEFHRTEN GEWHRLEISTUNGEN UND RECHTSMITTEL EXKLUSIV UND SCHLIESSEN JEGLICHE AUSDRCKLICHE, STILLSCHWEIGENDE, GESETZLICHE ODER ANDERWEITIGE GEWHRLEISTUNGEN UND RECHTSMITTEL AUS, U. A. STILLSCHWEIGENDE GEWHRLEISTUNGEN ZU HANDELSTAUGLICHKEIT ODER EIGNUNG FR EINEN BESTIMMTEN ZWECK, GESETZLICHE ODER ANDERWEITIGE GEWHRLEISTUNGEN, UND GARMIN SCHLIESST DIE VORGENANNTEN GEWHRLEISTUNGEN UND RECHTSMITTEL AUSDRCKLICH AUS. DIESE EINGESCHRNKTE GEWHRLEISTUNG GEWHRT IHNEN BESTIMMTE GESETZLICHE RECHTE; AUSSERDEM HABEN SIE GGF. ANDERE GESETZLICHE RECHTE, DIE JE NACH BUNDESLAND BZW. LAND VARIIEREN. FALLS STILLSCHWEIGENDE GEWHRLEISTUNGEN GEMSS DEN GESETZEN IHRES BUNDESLANDES ODER IHRES LANDES NICHT AUSGESCHLOSSEN WERDEN KNNEN, IST DIE DAUER DERARTIGER GEWHRLEISTUNGEN AUF DIE DAUER DIESER EINGESCHRNKTEN GEWHRLEISTUNG BESCHRNKT. IN EINIGEN BUNDESLNDERN

(BZW. LNDERN UND PROVINZEN) IST DIE EINSCHRNKUNG DER DAUER EINER EINGESCHRNKTEN GEWHRLEISTUNG NICHT GESTATTET; IN EINEM SOLCHEN FALL TRIFFT DER VORSTEHEND GENANNTE AUSSCHLUSS GGF. NICHT AUF SIE ZU. IN KEINERLEI FALL HAFTET GARMIN BEI EINEM GARANTIEANSPRUCH FR BEILUFIG ENTSTANDENE, KONKRETE, INDIREKTE SCHDEN ODER FOLGESCHDEN, DIE DURCH DIE SACH- ODER UNSACHGEMSSE VERWENDUNG ODER DIE NICHTVERWENDBARKEIT DIESES PRODUKTS ODER DEFEKTE DES PRODUKTS ENTSTEHEN. IN EINIGEN BUNDESLNDERN (SOWIE LNDERN UND PROVINZEN) IST DER AUSSCHLUSS VON BEILUFIG ENTSTANDENEN ODER FOLGESCHDEN NICHT GESTATTET; IN EINEM SOLCHEN FALL TREFFEN DIE VORGENANNTEN AUSSCHLSSE NICHT AUF SIE ZU. Falls Sie whrend des Gewhrleistungszeitraums gem dieser eingeschrnkten Gewhrleistung einen Garantieanspruch geltend machen, geht Garmin nach eigenem Ermessen folgendermaen vor und (i) repariert das Gert mit neuen Teilen oder mit gebrauchten Teilen, die die Qualittsstandards von Garmin erfllen, (ii) ersetzt das Gert durch ein neues oder berarbeitetes Gert, das die Qualittsstandards von Garmin erfllt, oder (iii) tauscht das Gert aus, wobei der volle Kaufpreis erstattet wird. DIESE RECHTSMITTEL SIND DIE EINZIGEN IHNEN IM FALLE EINES GARANTIEANSPRUCHS ZUR VERFGUNG STEHENDEN RECHTSMITTEL. Fr reparierte oder ersetzte Gerte gilt eine Gewhrleistung von 90 Tagen. Falls fr das eingesendete Gert weiterhin die ursprngliche Gewhrleistung gilt, betrgt die neue Gewhrleistung 90 Tage oder bis zum Ende der ursprnglichen einjhrigen Garantie, wobei der jeweils lngere Zeitraum Anwendung findet. Bevor Sie einen Garantieanspruch geltend machen, sehen Sie sich die unter support.garmin.com verfgbaren Online-Hilferessourcen an. Falls Sie diese Ressourcen verwenden und das Gert weiterhin nicht ordnungsgem funktioniert, wenden Sie sich an eine von Garmin autorisierte Serviceeinrichtung in dem Land, in dem Sie das Produkt ursprnglich erworben haben, oder folgen Sie den Anweisungen unter support.garmin.com, um einen Garantieanspruch geltend zu machen. Falls Sie sich in den USA befinden, knnen Sie sich auch telefonisch an 1-800-800-1020 wenden. Falls Sie einen Garantieanspruch auerhalb des Landes geltend machen, in dem Sie das Produkt ursprnglich erworben haben, kann Garmin nicht garantieren, dass die zum Reparieren oder Ersetzen des Produkts erforderlichen Teile und Produkte verfgbar sein werden; dies ist auf unterschiedliche Produktangebote und geltende Standards, Gesetze und Vorschriften zurckzufhren. In diesem Fall kann Garmin nach eigenem Ermessen und gem anwendbaren Gesetzen das Produkt reparieren oder ersetzen, wobei vergleichbare Garmin Produkte und Teile verwendet werden, oder verlangen, dass Sie das Produkt an eine von Garmin autorisierte Serviceeinrichtung in dem Land schicken, in dem Sie das Produkt ursprnglich erworben haben, oder an eine von Garmin autorisierte Serviceeinrichtung in einem anderen Land, die den Service des Produkts durchfhren kann; in diesem Fall unterliegt es Ihrer Verantwortung, alle anwendbaren Gesetze und Vorschriften bezglich Import und Export einzuhalten und fr alle Zollgebhren, die Mehrwertsteuer, Versandkosten und andere damit verbundene Steuern und Gebhren aufzukommen. In einigen Fllen knnen Garmin und seine Hndler Ihr Produkt nicht in einem anderen Land als dem Land warten, in dem Sie das Produkt nicht ursprnglich erworben haben, oder das reparierte oder ersetzte Produkt in dieses Land zurckschicken; dies ist auf geltende Standards, Gesetze und Vorschriften zurckzufhren. Kufe ber Onlineaktionen: Fr Produkte, die ber Onlineauktionen erworben wurden, besteht keinerlei Anspruch auf Rabatte oder andere, sich aus der Garantie ergebende Sonderangebote von Garmin. Online-Auktionsbesttigungen werden fr Garantieansprche nicht akzeptiert. Hierfr ist das Original oder eine Kopie des Kaufbelegs des ursprnglichen Einzelhndlers erforderlich. Garmin ersetzt keine fehlenden Komponenten bei Paketsendungen, die ber Online-Auktionen erworben wurden. Internationale Kufe: Fr ber internationale Vertriebspartner auerhalb der USA erworbene Gerte gilt mglicherweise abhngig vom jeweiligen Land eine separate Garantie. Sofern zutreffend wird diese Garantie von dem Vertriebspartner im jeweiligen Land angeboten, der auch den lokalen Service fr das Gert durchfhrt. Garantien von Vertriebspartnern gelten nur in dem fr den Vertrieb vorgesehenen Gebiet. Gewhrleistungsrichtlinie fr Marineprodukte: Fr einige Marineprodukte von Garmin gelten in bestimmten Gebieten ein lngerer Gewhrleistungszeitraum und zustzliche Bedingungen. Weitere Informationen sind unter www.garmin.com/support/warranty_marine verfgbar. Dort knnen Sie auch prfen, ob Ihr Produkt von der Garmin Gewhrleistungsrichtlinie fr Marineprodukte abgedeckt ist. INFORMACIN IMPORTANTE SOBRE EL PRODUCTO Y TU SEGURIDAD ADVERTENCIA Si no se cumplen las siguientes advertencias, se pueden provocar accidentes o colisiones que tengan como consecuencia la muerte o lesiones graves. Avisos sobre la utilizacin en entornos nuticos T eres el responsable del uso seguro y prudente de la embarcacin. Este dispositivo es una herramienta que mejorar la capacidad de dirigir la embarcacin. Este dispositivo no te exime de la responsabilidad de utilizar de forma segura la embarcacin. Evita los riesgos de navegacin y nunca dejes el timn sin supervisin. Utiliza esta unidad slo como ayuda para la navegacin. No intentes utilizar la unidad para cualquier otro propsito que requiera mediciones precisas de la direccin, la distancia, la ubicacin o la topografa. Permanece siempre preparado para retomar rpidamente el control de la embarcacin. Mantn la precaucin cuando lo utilices cerca de obstculos en el agua, como diques, pilotes u otras embarcaciones. Al navegar, si la unidad dispone de funciones de navegacin, compara con atencin la informacin que aparece en el dispositivo con todas las fuentes de navegacin disponibles, incluida la informacin de seales, las regulaciones y restricciones locales de los canales de navegacin y los mapas. Para mayor seguridad, resuelve cualquier discrepancia o duda antes de continuar con la navegacin. Si la unidad utiliza mapas, utiliza la carta electrnica del dispositivo slo con fines de ayuda y nunca para sustituir cartas autorizadas por el gobierno. Las cartas oficiales del gobierno y los avisos a los navegantes contienen toda la informacin necesaria para navegar de forma segura. Si la unidad proporciona datos de profundidad, no deben utilizarse como referencia principal para evitar embarrancamientos o colisiones. Las lecturas de los datos de profundidad deben complementarse con la informacin de las cartas en papel y los indicadores visuales correspondientes. Si hay indicios de aguas poco profundas u objetos sumergidos, la embarcacin deber manejarse a una velocidad reducida. De no tenerse en cuenta este aviso, podran producirse daos personales o en la embarcacin. Si la unidad dispone de funciones de entrada de vdeo, no intentes utilizar o ver vdeos mientras ests utilizando o pilotando el barco. El uso o la visualizacin de entrada de vdeo mientras se mueve la embarcacin podra provocar un accidente o colisin que cause la muerte, lesiones graves o daos materiales. Aviso sobre daos en el odo Escuchar el sistema estreo a un volumen demasiado alto puede deteriorar la audicin. AVISO Si no se tiene en cuenta el siguiente aviso, podran producirse lesiones personales o daos materiales, y la funcionalidad del dispositivo podra verse afectada negativamente. Aviso sobre la batera Ponte en contacto con el servicio local de eliminacin de residuos para desechar el dispositivo o la batera de forma que cumpla todas las leyes y normativas locales aplicables. Aviso sobre el GPS El dispositivo de navegacin puede sufrir una degradacin en el funcionamiento si se utiliza cerca de cualquier dispositivo que utilice una red de banda ancha terrestre que funcione con frecuencias prximas a las utilizadas por cualquier sistema global de navegacin por satlite

(GNSS), como el servicio de posicionamiento global (GPS). El uso de dichos dispositivos puede impedir la recepcin de seales GNSS. Programas medioambientales para el producto Puedes consultar la informacin acerca del programa de reciclado de productos de Garmin y la directiva WEEE, RoHS y REACH, as como de otros programas de cumplimiento en www.garmin.com/aboutGarmin/environment. Declaracin de conformidad Por la presente, Garmin declara que este producto cumple con la Directiva 2014/53/UE. El texto completo de la declaracin de conformidad de la UE est disponible en la siguiente direccin de Internet: www.garmin.com/compliance. Conformidad con COFETEL/IFETEL La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Informacin sobre datos de mapas Garmin utiliza una serie de fuentes de datos privadas y gubernamentales. Prcticamente todas las fuentes de datos contienen algunos datos inexactos o incompletos. En algunos pases, la informacin completa y precisa de mapas no est disponible o lo est a un precio muy elevado. Acuerdo de licencia del software AL UTILIZAR EL DISPOSITIVO, EL USUARIO SE COMPROMETE A RESPETAR LOS TRMINOS Y CONDICIONES DEL SIGUIENTE ACUERDO DE LICENCIA DEL SOFTWARE. EL USUARIO DEBER LEER ESTE ACUERDO ATENTAMENTE. Garmin Ltd. y sus subsidiarias (Garmin) conceden al usuario una licencia limitada para utilizar el software incluido en este dispositivo (el Software) en formato binario ejecutable durante el uso normal del producto. La titularidad, los derechos de propiedad y los derechos de propiedad intelectual del Software seguirn perteneciendo a Garmin y/o sus terceros proveedores. 5 El usuario reconoce que el Software es propiedad de Garmin y/o sus proveedores terceros, y que est protegido por las leyes de propiedad intelectual de Estados Unidos y tratados internacionales de copyright. Tambin reconoce que la estructura, la organizacin y el cdigo del Software, del que no se facilita el cdigo fuente, son secretos comerciales valiosos de Garmin y/o sus terceros proveedores, y que el Software en su formato de cdigo fuente es un secreto comercial valioso de Garmin y/o sus terceros proveedores. Por la presente, el usuario se compromete a no descompilar, desmontar, modificar, invertir el montaje, utilizar tcnicas de ingeniera inversa o reducir a un formato legible para las personas el Software o cualquier parte de ste ni crear cualquier producto derivado a partir del Software. Asimismo, se compromete a no exportar ni reexportar el Software a ningn pas que contravenga las leyes de control de las exportaciones de Estados Unidos o de cualquier otro pas aplicable. Garanta limitada ESTA GARANTA LIMITADA PROPORCIONA DERECHOS LEGALES ESPECFICOS AL USUARIO, QUIEN PODR TENER OTROS DERECHOS LEGALES QUE PUEDEN VARIAR SEGN LA REGIN, EL PAS O LA PROVINCIA. GARMIN NO EXCLUYE, LIMITA NI SUSPENDE OTROS DERECHOS LEGALES QUE EL USUARIO PUEDA TENER EN VIRTUD DE LAS LEYES DE SU REGIN, PAS O PROVINCIA. PARA UNA COMPLETA COMPRENSIN DE SUS DERECHOS, EL USUARIO DEBER CONSULTAR LAS LEYES VIGENTES EN SU REGIN, PAS O PROVINCIA. Los productos no relacionados con la aviacin estn garantizados frente a defectos de materiales o mano de obra durante un ao a partir de la fecha de compra. En este periodo, Garmin puede, segn su criterio, reparar o sustituir cualquier componente que no funcione correctamente. Estas reparaciones o sustituciones se realizarn sin coste alguno para el cliente en concepto de piezas o mano de obra, siempre y cuando el cliente se haga responsable de los gastos de envo. Esta garanta limitada no se aplica a: (i) los daos estticos, tales como araazos, marcas o abolladuras; (ii) las piezas consumibles, tales como las bateras, a no ser que el dao se haya producido por un defecto de los materiales o de la mano de obra; (iii) los daos provocados por accidentes, uso inadecuado, el agua, inundaciones, fuego, otras causas de fuerza mayor o causas externas; (iv) los daos provocados por reparaciones realizadas por un proveedor de servicio no autorizado por Garmin; (v) los daos ocurridos en productos que hayan sido modificados o alterados sin la autorizacin por escrito de Garmin; o (vi) los daos ocurridos en productos conectados a la fuente de alimentacin y/o cables de datos no suministrados por Garmin. Adems, Garmin se reserva el derecho a rechazar reclamaciones de garanta de productos o servicios obtenidos y/o utilizados en contra de las leyes de cualquier pas.Los productos de navegacin Garmin se han diseado solamente para proporcionar ayuda durante el viaje y no debern utilizarse con ningn propsito que requiera el clculo preciso de una direccin, distancia, ubicacin o topografa. Garmin no garantiza la precisin ni la integridad de los datos de mapas. Esta garanta limitada tampoco se aplica a, y Garmin no se hace responsable de, la degradacin en el funcionamiento de cualquier producto de navegacin de Garmin que derive de su uso cerca de cualquier dispositivo de mano u otro dispositivo que utilice una red de banda ancha terrestre que funcione con frecuencias prximas a las frecuencias utilizadas por cualquier sistema global de navegacin por satlite (GNSS), como el servicio de posicionamiento global

(GPS). El uso de dichos dispositivos puede impedir la recepcin de seales GNSS. HASTA EL LMITE MXIMO PERMITIDO POR LA LEY EN VIGOR, LAS GARANTAS Y RECURSOS EXPRESADOS EN ESTA GARANTA LIMITADA SON EXCLUSIVOS Y SUSTITUYEN A CUALESQUIERA OTRAS GARANTAS Y RECURSOS, A LAS QUE GARMIN RENUNCIA EXPRESAMENTE, YA SEAN EXPRESAS, IMPLCITAS, REGLAMENTARIAS O, POR EL CONTRARIO, INCLUIDAS, ENTRE OTRAS, CUALQUIER GARANTA IMPLCITA DE COMERCIABILIDAD O IDONEIDAD PARA UN FIN DETERMINADO, YA SEAN REGLAMENTARIAS O DE OTRO TIPO. ESTA GARANTA LIMITADA PROPORCIONA DERECHOS LEGALES ESPECFICOS AL USUARIO, QUIEN PODR TENER OTROS DERECHOS LEGALES QUE PUEDEN VARIAR SEGN LA REGIN Y EL PAS. SI NO SE PUEDE RENUNCIAR A LAS GARANTAS IMPLCITAS EN VIRTUD DE LAS LEYES DE LA REGIN O PAS DEL USUARIO, DICHAS GARANTAS SE LIMITAN A LA DURACIN DE ESTA GARANTA LIMITADA. EN ALGUNAS REGIONES, PASES Y PROVINCIAS, NO SE PERMITEN LIMITACIONES DE DURACIN DE LAS GARANTAS IMPLCITAS, POR LO QUE ES POSIBLE QUE LA LIMITACIN ANTERIOR NO SE APLIQUE AL USUARIO. EN CASO DE INCUMPLIMIENTO DE LA GARANTA, GARMIN NO SE HAR RESPONSABLE BAJO NINGN CONCEPTO DE LOS DAOS IMPREVISTOS, ESPECIALES, INDIRECTOS O EMERGENTES, TANTO SI SON RESULTADO DE LA UTILIZACIN, MALA UTILIZACIN O DESCONOCIMIENTO DEL MANEJO DE ESTE PRODUCTO, COMO SI LO SON POR DEFECTOS EN ESTE. EN ALGUNAS REGIONES, PASES Y PROVINCIAS, NO SE PERMITE LA EXCLUSIN DE DAOS FORTUITOS O DERIVADOS, POR LO QUE ES POSIBLE QUE ESTA RESTRICCIN NO SEA APLICABLE EN EL CASO DEL USUARIO. Si durante el periodo de garanta, el usuario solicita un servicio de garanta de acuerdo con esta Garanta limitada, Garmin llevar a cabo, segn su criterio, una de las siguientes opciones: (i) reparar el dispositivo utilizando piezas nuevas o piezas usadas con anterioridad que cumplan con los estndares de calidad de Garmin; (ii) sustituir el dispositivo por un dispositivo nuevo o un dispositivo restaurado que cumpla con los estndares de calidad de Garmin; (iii) cambiar el dispositivo por un reembolso completo equivalente al precio de compra.Garmin ESTE RECURSO SER NICO Y EXCLUSIVO EN CASO DE INCUMPLIMIENTO DE LA GARANTA. Los dispositivos reparados o sustituidos tienen una garanta de 90 das. Si la unidad enviada est cubierta por la garanta original, la nueva garanta es de 90 das o hasta el final del periodo de garanta original de un ao, siendo aplicable el periodo de mayor duracin. Antes de solicitar el servicio de garanta, el usuario deber acceder a los recursos de ayuda en lnea disponibles en support.garmin.com y consultarlos. Si el dispositivo sigue sin funcionar correctamente despus de hacer uso de estos recursos, se deber contactar con un centro de servicio autorizado de Garmin del pas donde se realiz la compra, o bien seguir las instrucciones disponibles en support.garmin.com para obtener servicio de garanta. Si el usuario se encuentra en Estados Unidos, tambin puede llamar al 1-800-800-1020. Si se desea solicitar el servicio de garanta en un pas distinto de donde se realiz la compra, Garmin no puede garantizar que las piezas y los productos necesarios para reparar o sustituir el producto estn disponibles debido a las diferencias en las ofertas de productos y los estndares, leyes y normativas de aplicacin. En ese caso, Garmin puede, a su entera discrecin y segn las leyes aplicables, reparar o sustituir el producto con productos y piezas de Garmin equiparables, o solicitar al usuario que enve su producto a un centro de servicio autorizado de Garmin del pas donde se realiz la compra o un centro de servicio autorizado de Garmin de otro pas que pueda realizar el mantenimiento de su producto, en cuyo caso el usuario ser responsable de cumplir con todas las leyes y normativas de importacin y exportacin, as como de realizar el pago de todos los impuestos de aduanas, IVA, gastos de envo y otros impuestos y gastos asociados. En algunos casos, es posible que Garmin y sus distribuidores no puedan realizar el mantenimiento del producto del usuario en un pas distinto de donde se realiz la compra, o devolver un producto reparado o sustituido en tal pas debido a los estndares, leyes o normativas vigentes en el mismo. Compras en subastas en lnea: los productos que se adquieren a travs de subastas en lnea no pueden formar parte de los descuentos u otras ofertas especiales de la cobertura de la garanta de Garmin. No se aceptan las confirmaciones de subasta en lnea como comprobante de garanta. Para recibir asistencia dentro del periodo de garanta, se necesita el original o una copia de la factura del establecimiento de compra original. Garmin no sustituir componentes que falten de cualquier caja que se compre a travs de una subasta en lnea. Ventas internacionales: segn el pas, los distribuidores internacionales pueden ofrecer una garanta por separado para los dispositivos adquiridos fuera de Estados Unidos. Si corresponde, los distribuidores locales de cada pas ofrecen esta garanta y son estos distribuidores los que 6 proporcionan un servicio local para el dispositivo. Las garantas del distribuidor son vlidas solamente en el rea de distribucin proyectada. Poltica de garanta nutica: determinados productos nuticos de Garmin en reas concretas tienen un periodo de garanta mayor y unos trminos y condiciones adicionales. Visita www.garmin.com/support/warranty_marine para obtener ms informacin y ver si tu producto est cubierto por la Poltica de garanta nutica de Garmin. INFORMAES IMPORTANTES SOBRE SEGURANA E O PRODUTO ATENO No seguir estes avisos pode resultar em acidente ou coliso, resultando em morte ou ferimentos graves. Avisos de operao martima Voc responsvel pela operao prudente e segura da sua embarcao. Este dispositivo uma ferramenta que aprimorar a operao da sua embarcao. Este dispositivo no o isenta da responsabilidade de operar sua embarcao com segurana. Evite perigos na navegao e nunca deixe o leme sem superviso. Use este dispositivo somente como assistncia navegao. No tente usar o dispositivo para qualquer finalidade que exija medio precisa da direo, distncia, localizao ou topografia. Esteja sempre preparado para retomar o controle da embarcao. Tome cuidado prximo a ameaas e perigos na gua, como cais, estacas e outras embarcaes. Se o dispositivo contar com recursos de navegao, ao navegar, compare as informaes exibidas no dispositivo a todas as demais fontes de navegao disponveis, inclusive informaes de apurao visual, normas e restries de navegao locais e mapas. Por motivo de segurana, sempre resolva quaisquer discrepncias ou dvidas antes de prosseguir com a navegao. Se o dispositivo usar mapas, use o grfico eletrnico no dispositivo somente para facilitar, o uso de grficos autorizados pelo governo, e no para substitu-los. Avisos e grficos oficiais do governo para marinheiros contm todas as informaes necessrias para navegar com segurana. Se o dispositivo apresentar dados sobre a profundidade, esses dados no devem ser usados como o principal meio de evitar colises e encalhes. Leituras de dados complementares sobre profundidade com informaes de grficos impressos e indicadores visuais aplicveis. Sempre operar a embarcao em baixa velocidade caso haja suspeita de guas rasas e objetos submersos. O desrespeito deste aviso poder provocar danos na embarcao ou ferimentos. Se o dispositivo tiver recursos de entrada de vdeo, no tente operar ou assistir ao vdeo enquanto estiver operando ou navegando sua embarcao. Operar ou assistir ao vdeo enquanto a embarcao estiver em movimento pode causar acidentes ou colises que podem resultar em danos materiais, ferimentos graves ou morte. Aviso sobre danos audio Ouvir ao estreo em volume alto pode causar danos audio. AVISO O desrespeito a este aviso pode resultar em danos pessoais ou da propriedade, ou afetar negativamente a funcionalidade do dispositivo. Aviso da bateria Entre em contato com seu departamento de tratamento de resduos local para eliminar corretamente o dispositivo/baterias de acordo com as leis e os regulamentos locais vigentes. Aviso do GPS O dispositivo de navegao pode ter o desempenho degradado se voc us-lo prximo a qualquer dispositivo que use uma rede de banda larga terrestre funcionando prximo s frequncias usadas por quaisquer Dados de posio do sistema de navegao global via satlite (GNSS), como o Global Positioning Service (GPS). O uso dos referidos dispositivos podem prejudicar a recepo de sinais de GNSS. Programas Ambientais do Produto Informaes sobre o programa de reciclagem de produtos da Garmin, sobre WEEE, RoHS, REACH e outros programas de conformidade podem ser consultadas em www.garmin.com

/aboutGarmin/environment. Declarao de Conformidade Pelo presente, a Garmin declara que este produto est em conformidade com a Diretiva 2014/53/EU. O texto completo da declarao de conformidade da EU est disponvel no seguinte endereo da Internet: www.garmin.com/compliance. Informaes de Radiocomunicao Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. Informaes Sobre os Dados do Mapa A Garmin recorre a uma combinao de fontes de dados privadas e governamentais. Praticamente todas as fontes de dados contm alguns dados imprecisos ou incompletos. Em alguns pases, informaes de mapa completas e precisas no esto disponveis ou so extremamente caras. Garantia limitada ESTA GARANTIA LIMITADA LHE CONCEDE DIREITOS LEGAIS ESPECFICOS E TAMBM OUTROS DIREITOS LEGAIS QUE PODEM VARIAR DE ACORDO COM O ESTADO (OU DE ACORDO COM O PAS OU A PROVNCIA). A GARMIN NO EXCLUI, LIMITA OU SUSPENDE OUTROS DIREITOS LEGAIS QUE VOC POSSA TER EM CONFORMIDADE COM AS LEIS DO SEU ESTADO (OU PAS OU PROVNCIA). PARA UM ENTENDIMENTO COMPLETO DOS SEUS DIREITOS, VOC DEVE CONSULTAR AS LEIS DO SEU ESTADO, PAS OU PROVNCIA. Os produtos no relacionados aviao tm garantia de ausncia de defeitos de material e fabricao por um ano a partir da data da compra. Durante este perodo, a Garmin reparar ou substituir, exclusivamente a seu prprio critrio, os componentes que no apresentarem o desempenho normal esperado. Tal reparo ou substituio ser feito sem custo para o cliente com relao a peas ou trabalho, desde que o cliente se responsabilize por qualquer custo de transporte. Esta Garantia Limitada no se aplica a: (i) danos externos, tais como riscos, cortes e amassados; (ii) peas consumveis, tais como pilhas, salvo se os danos no produto forem resultantes de um defeito de materiais ou de mo de obra; (iii) danos resultantes de acidentes, uso excessivo ou incorreto, gua, inundaes, incndios ou outras causas naturais ou externas;

(iv) danos causados por reparos realizados por qualquer pessoa que no seja um fornecedor de servios autorizado da Garmin; (v) danos em qualquer produto que tenha sido sujeito a modificaes ou alteraes sem a autorizao por escrito da Garmin; ou (vi) danos em qualquer produto que tenha sido ligado a cabos de alimentao/dados no fornecidos pela Garmin. Alm disso, a Garmin reserva-se o direito de recusar servios de garantia de produtos ou reparaes obtidos e/ou utilizados em transgresso das leis de qualquer pas.Os produtos de navegao da Garmin foram concebidos para serem usados exclusivamente como auxlio em viagens, no podendo nunca ser utilizados para quaisquer finalidades que requerem medies precisas de direo, distncia, localizao ou topografia.A Garmin no oferece quaisquer garantias quanto exatido ou preciso dos dados do mapa. Esta Garantia Limitada tambm no se aplica a, e a Garmin no responsvel por, qualquer degradao no desempenho de qualquer produto de navegao Garmin resultando do uso prximo a qualquer dispositivo porttil ou outro que utilize uma rede de banda larga terrestre funcionando em frequncias que so prximas s frequncias usadas por quaisquer Dados de posio do sistema de navegao global via satlite (GNSS), como o Global Positioning Service

(GPS). O uso dos referidos dispositivos pode prejudicar a recepo de sinais de GNSS. AT O LIMITE MXIMO PERMITIDO PELA LEI APLICVEL, AS GARANTIAS E OS RECURSOS CONTIDOS NESTA GARANTIA LIMITADA SO EXCLUSIVOS E SUBSTITUEM QUALQUER OUTRA GARANTIA, E A GARMIN RENUNCIA EXPRESSAMENTE TODAS AS OUTRAS GARANTIAS E RECURSOS, EXPRESSOS OU IMPLCITOS, ESTATUTRIOS OU DE OUTRA MANEIRA, INCLUINDO, MAS SEM LIMITAO, QUALQUER OUTRA GARANTIA IMPLCITA DE COMERCIABILIDADE OU ADEQUAO PARA UM DETERMINADO FIM, ESTATUTRIO OU DE OUTRA MANEIRA. ESTA GARANTIA LIMITADA LHE CONCEDE DIREITOS LEGAIS ESPECFICOS E TAMBM OUTROS DIREITOS LEGAIS QUE PODEM VARIAR DE ACORDO COM O ESTADO E DE ACORDO COM O PAS OU A PROVNCIA. SE GARANTIAS IMPLCITAS NO PUDEREM SER RENUNCIADAS EM CONFORMIDADE COM AS LEIS DO SEU ESTADO OU PAS, AS REFERIDAS GARANTIAS SO LIMITADAS DURANTE O PERODO DE DURAO DESTA GARANTIA LIMITADA. ALGUNS ESTADOS (E PASES E PROVNCIAS) NO PERMITEM LIMITAES SOBRE A DURAO DE UMA GARANTIA IMPLCITA, PORTANTO AS RESTRIES ACIMA PODEM NO SE APLICAR A VOC. SOB NENHUMA CIRCUNSTNCIA A GARMIN SER RESPONSVEL MEDIANTE SOLICITAO DE VIOLAO DE GARANTIA POR DANOS INCIDENTAIS, ESPECIAIS, INDIRETOS OU CONSEQUENTES, CAUSADOS PELA UTILIZAO, M UTILIZAO OU INCAPACIDADE DE UTILIZAO DESTE PRODUTO OU POR DEFEITOS NESTE. ALGUNS ESTADOS (E PASES E PROVNCIAS) NO PERMITEM A EXCLUSO DE INDENIZAES INCIDENTAIS OU CONSEQUENCIAIS, PORTANTO AS RESTRIES ACIMA PODEM NO SE APLICAR A VOC. Se, durante o perodo de garantia, voc enviar uma solicitao de servio de garantia de acordo com esta Garantia Limitada, a Garmin, a seu critrio: (i) reparar o dispositivo utilizando peas novas ou peas utilizadas anteriormente que atendam aos padres de qualidade da Garmin; (ii) substituir o dispositivo por um novo dispositivo ou um dispositivo renovado que atenda aos padres de qualidade da Garmin ou (iii) trocar o dispositivo por um reembolso total do seu preo de compra. TAL RECURSO CONSTITUIR SEU NICO E EXCLUSIVO RECURSO PARA QUALQUER VIOLAO DE GARANTIA. Dispositivos reparados ou substitudos tm garantia de 90 dias. Se a unidade enviada ainda estiver coberta pela garantia original, a nova garantia ser de 90 dias ou at o final da garantia original de 1 ano, o que tiver uma durao maior. Antes de procurar o servio de garantia, acesse e revise os recursos de ajuda on-line disponveis em support.garmin.com. Se o seu dispositivo ainda no estiver funcionando corretamente depois de usar esses recursos, entre em contato com uma Instalao de servio autorizada da Garmin no pas original da compra ou siga as instrues no site support.garmin.com para obter o servio de garantia. Se voc est localizado nos Estados Unidos, tambm pode ligar para 1-800-800-1020. Se voc procurar o servio de garantia fora do pas original de compra, a Garmin no pode garantir que as peas e os produtos necessrios para reparar ou substituir o seu produto estaro disponveis, devido a diferenas nas ofertas de produtos e nas normas, leis e regulamentos aplicveis. Nesse caso, a Garmin poder, a seu exclusivo critrio e sujeito s leis aplicveis, reparar ou substituir o seu produto por produtos e peas comparveis da Garmin, ou exigir que voc envie seu produto para uma Instalao de servio autorizado da Garmin no pas de compra original ou para uma Instalao de servio autorizado da Garmin em outro pas que possa atender seu produto e, nesse caso, voc ser responsvel por cumprir todas as leis e regulamentos aplicveis de importao e exportao e por pagar todos os impostos alfandegrios, IVA, taxas de transporte e outros impostos e taxas associados. Em alguns casos, a Garmin e seus revendedores podem no ser capazes de atender seu produto em um pas fora do pas original de compra ou de devolver um produto reparado ou substitudo para voc nesse pas, devido s normas, leis ou regulamentos aplicveis nesse pas. Compras em leiles online: os produtos comprados em leiles online no so passveis de abatimento ou outra oferta especial da cobertura de garantia da Garmin. Confirmaes de compra em leiles on-line no so aceitas para verificao da garantia. Para obter o servio de garantia, necessria a nota de venda original, ou uma cpia, do distribuidor original.A Garmin no substitui componentes em falta de qualquer pacote adquirido atravs de leiles online. Compras Internacionais: dependendo do pas, uma garantia separada deve ser oferecida por distribuidores internacionais para dispositivos adquiridos fora dos Estados Unidos. Se aplicvel, essa garantia pode ser providenciada pelo distribuidor local no pas, e esse distribuidor oferecer manuteno local para seu dispositivo. As garantias do distribuidor so vlidas apenas na rea de distribuio pretendida. Poltica de Garantia de Produtos Nuticos: determinados produtos nuticos da Garmin em determinadas reas tm um perodo de garantia maior e termos e condies adicionais. Acesse www.garmin.com/support/warranty_marine para obter mais detalhes e ver se seu produto est coberto pela Poltica de Garantia de Produtos Nuticos Garmin. BELANGRIJKE VEILIGHEIDS- EN PRODUCTINFORMATIE WAARSCHUWING Als u de volgende waarschuwingen negeert, kan dit leiden tot een ongeval of aanrijding, wat de dood of ernstig letsel tot gevolg kan hebben. Waarschuwing over de bediening voor de watersport U bent verantwoordelijk voor de veilige en voorzichtige besturing van uw vaartuig. Dit toestel is een hulpmiddel waarmee u uw vaartuig beter kunt besturen. Het toestel ontheft u echter niet van uw verantwoordelijkheid om het vaartuig veilig te besturen. Voorkom gevaarlijke navigatie en zorg ervoor dat het roer nooit onbemand is. Gebruik dit toestel uitsluitend als navigatiehulpmiddel. Gebruik het toestel niet voor doeleinden waarbij precieze bepalingen van richting, afstand, locatie of topografie zijn vereist. Wees altijd bereid om snel de besturing van uw vaartuig over te nemen. Wees voorzichtig in de buurt van gevaren op het water, zoals dokken, palen en andere vaartuigen. Als het toestel navigatiemogelijkheden heeft, vergelijkt u de informatie die het toestel weergeeft tijdens het navigeren met alle beschikbare navigatiebronnen, inclusief informatie van visuele waarnemingen, uit lokale voorschriften en beperkingen voor waterwegen, en van kaarten. Los voor uw eigen veiligheid eventuele verschillen of zaken die u zich afvraagt altijd op voor u verdergaat. Als het toestel gebruikmaakt van kaarten, gebruikt u de elektronische kaart in het toestel alleen om het gebruik van door de overheid goedgekeurde kaarten te vergemakkelijken, niet om deze te vervangen. De officile overheidskaarten en -mededelingen voor zeevarenden bevatten alle informatie die nodig is om veilig te kunnen navigeren. Als het toestel dieptegegevens verstrekt, mogen deze niet als primaire informatiebron worden gebruikt om aanvaringen en aan de grond lopen te voorkomen. Vul dieptegegevens van dit product aan met informatie van waterkaarten en visuele aanwijzingen. Vaar altijd met lage snelheid als u ondiep water of obstakels onder water vermoedt. Het niet in acht nemen van deze waarschuwing kan leiden tot schade aan het vaartuig of persoonlijk letsel. Als het toestel over videomogelijkheden beschikt, probeer dan geen video te bedienen of te bekijken terwijl u uw vaartuig bestuurt of navigeert. Het bedienen of bekijken van de video terwijl het vaartuig beweegt kan leiden tot een ongeval of aanvaring en kan beschadiging van eigendommen, ernstige verwondingen of de dood tot gevolg hebben. Waarschuwing tegen gehoorbeschadiging Luisteren naar de stereo op hoog volume kan uw gehoor beschadigen. LET OP Het negeren van de volgende kennisgeving kan leiden tot persoonlijke of materile schade of nadelige gevolgen voor de functionaliteit van het toestel. Batterijmelding Neem volgens de plaatselijke regelgeving contact op met de afvalverwerker om het toestel/

batterijen af te danken. Kennisgeving over GPS Het navigatietoestel presteert mogelijk minder goed als u het gebruikt in de buurt van een toestel dat gebruikmaakt van een Terrestrial Broadband Network dat werkt op frequenties die dichtbij de frequenties liggen die door een Global Navigation Satellite System (GNSS), zoals de Global Positioning Service (GPS), worden gebruikt. Het gebruik van dergelijke toestellen kan de ontvangst van GNSS-signalen verstoren. Productmilieuprogramma's Informatie over het hergebruikprogramma van Garmin en informatie over naleving van WEEE, RoHS, REACH en andere programma's vindt u op www.garmin.com/aboutGarmin/environment. Conformiteitsverklaring Hierbij verklaart Garmin dat dit product voldoet aan de richtlijn 2014/53/EU. De volledige tekst van deze EU-conformiteitsverklaring is beschikbaar op de volgende website: www.garmin.com

/compliance. Informatie over de kaartgegevens Garmin gebruikt deels gegevensbronnen van de overheid en deels particuliere gegevensbronnen. Vrijwel alle gegevensbronnen bevatten een bepaalde mate van onnauwkeurigheid. In sommige landen zijn volledige en nauwkeurige kaartgegevens niet beschikbaar of onbetaalbaar. Beperkte garantie DEZE BEPERKTE GARANTIE VERLEENT U SPECIFIEKE WETTELIJKE RECHTEN EN U HEBT MOGELIJK ANDERE WETTELIJKE RECHTEN DIE PER STAAT (OF PER LAND OF PROVINCIE) KUNNEN VERSCHILLEN. ANDERE WETTELIJKE RECHTEN DIE U HEBT VOLGENS DE WETGEVING VAN UW STAAT (OF LAND OF PROVINCIE) WORDEN DOOR GARMIN NIET UITGESLOTEN, BEPERKT OF OPGESCHORT. VOOR EEN VOLLEDIG INZICHT IN UW RECHTEN DIENT U DE WETGEVING VA UW STAAT, LAND OF PROVINCIE TE RAADPLEGEN. Producten die niet voor de luchtvaart zijn bestemd, zijn gegarandeerd vrij van defecten in materiaal en techniek gedurende n jaar na de aankoopdatum. Binnen deze periode zal Garmin alle onderdelen waarvan een normaal gebruik niet mogelijk is, naar eigen keuze repareren of vervangen. Voor dergelijke reparaties of vervangingen zullen aan de klant geen kosten worden gefactureerd voor onderdelen of arbeid, op voorwaarde dat de klant verantwoordelijk blijft voor eventuele transportkosten. Deze Beperkte garantie is niet van toepassing op: (i) cosmetische schade, zoals krassen, sneden en deuken; (ii) verbruiksgoederen, zoals batterijen, tenzij productschade het gevolg is van defect materiaal of ondeugdelijk vakmanschap; (iii) schade als gevolg van ongelukken, misbruik, verkeerd gebruik, water, overstroming, brand of andere natuurrampen of externe oorzaken; (iv) schade als gevolg van onderhoud uitgevoerd door personen die niet door Garmin bevoegd zijn verklaard tot het uitvoeren van onderhoud; (v) schade aan een product dat is veranderd zonder de schriftelijke toestemming van Garmin of (vi) schade aan een product dat is aangesloten op voedings- en/of gegevenskabels die niet door Garmin zijn meegeleverd. Bovendien behoudt Garmin zich het recht voor garantieclaims af te wijzen voor producten of diensten die zijn verkregen en/of gebruikt in strijd met de wetten van een land. Garmin navigatieproducten zijn uitsluitend bestemd voor gebruik als hulp bij het reizen en mogen niet worden gebruikt voor doeleinden waarbij precieze metingen van richting, afstand, locatie of topografie vereist zijn. Garmin geeft geen enkele garantie op de nauwkeurigheid of volledigheid van de kaartgegevens. Deze Beperkte garantie is eveneens niet van toepassing op, en Garmin is niet aansprakelijk wegens, verslechtering van de prestaties van een Garmin navigatieproduct als gevolg van het gebruik ervan in de buurt van een handset of ander toestel dat gebruikmaakt van een Terrestrial Broadband Network dat werkt op frequenties die dicht bij de frequenties liggen die door een Global Navigation Satellite System (GNSS), zoals de Global Positioning Service (GPS), worden gebruikt. Het gebruik van dergelijke toestellen kan de ontvangst van GNSS-signalen verstoren. VOOR ZOVER TOEGESTAAN VOLGENS TOEPASSELIJK RECHT, ZIJN DE HIERIN VERVATTE GARANTIES EN VERHAALSMOGELIJKHEDEN EXCLUSIEF EN TREDEN DEZE IN DE PLAATS VAN ALLE OVERIGE GARANTIES EN VERHAALSMOGELIJKHEDEN, EXPLICIET, IMPLICIET, WETTELIJK OF ANDERSZINS, EN WIJST GARMIN DERGELIJKE OVERIGE GARANTIES EN VERHAALSMOGELIJKHEDEN UITDRUKKELIJK AF, MET INBEGRIP VAN, DOCH NIET BEPERKT TOT, IMPLICIETE GARANTIES VAN VERKOOPBAARHEID OF GESCHIKTHEID VOOR EEN BEPAALD DOEL, WETTELIJK VERHAALSRECHT OF ANDERSZINS. DEZE BEPERKTE GARANTIE VERLEENT U SPECIFIEKE WETTELIJKE RECHTEN EN U HEBT MOGELIJK ANDERE WETTELIJKE RECHTEN DIE PER STAAT (OF PER LAND) KUNNEN VERSCHILLEN. ALS IMPLICIETE GARANTIES NIET KUNNEN WORDEN AFGEWEZEN VOLGENS DE WETGEVING VAN UW STAAT OF LAND, ZIJN DERGELIJKE GARANTIES WAT BETREFT DUUR BEPERKT TOT DE DUUR VAN DEZE BEPERKTE GARANTIE. IN SOMMIGE STATEN (EN LANDEN EN PROVINCIES) IS BEPERKING VAN DE DUUR VAN EEN IMPLICIETE GARANTIE NIET TOEGESTAAN, ZODAT DE BOVENGENOEMDE BEPERKING OP U MOGELIJK NIET VAN TOEPASSING IS. IN GEEN ENKEL GEVAL ZAL GARMIN IN EEN VORDERING WEGENS INBREUK OP DE GARANTIE AANSPRAKELIJK ZIJN VOOR ENIGE INCIDENTELE, SPECIALE, INDIRECTE OF GEVOLGSCHADE, OF DEZE NU HET RESULTAAT IS VAN HET GEBRUIK, MISBRUIK OF ONVERMOGEN OM DIT PRODUCT TE GEBRUIKEN, OF VAN EEN DEFECT VAN HET PRODUCT. IN BEPAALDE STATEN (EN LANDEN EN PROVINCIES) IS DE UITSLUITING VAN INCIDENTELE OF GEVOLGSCHADE NIET TOEGESTAAN. DE BOVENSTAANDE BEPERKINGEN ZIJN MOGELIJK NIET OP U VAN TOEPASSING. Als u tijdens de garantieperiode een claim voor garantieservice indient in overeenstemming met deze Beperkte garantie, kiest Garmin naar eigen inzicht voor: (i) reparatie van het toestel met nieuwe of gebruikte onderdelen die aan de kwaliteitsnormen van Garmin voldoen, (ii) vervanging van het toestel door een nieuw of gereviseerd toestel dat aan de kwaliteitsnormen van Garmin voldoet of (iii) inruil van het toestel tegen vergoeding van uw volledige aankoopbedrag. EEN DERGELIJKE VERHAALMOGELIJKHEID ZAL UW ENIGE EN EXCLUSIEVE VERHAALMOGELIJKHEID ZIJN INDIEN DE GARANTIE NIET WORDT GERESPECTEERD. U hebt 90 dagen garantie op gerepareerde of vervangen toestellen. Als het toestel ter reparatie wordt opgestuurd tijdens de originele garantieperiode, duurt de nieuwe garantieperiode 90 dagen of tot het einde van de originele garantieperiode van 1 jaar, naargelang welke periode het langst duurt. Raadpleeg de online hulpbronnen op support.garmin.com voordat u garantieservice aanvraagt. Als u deze informatie hebt geraadpleegd en het toestel daarna nog steeds niet naar behoren functioneert, kunt u contact opnemen met een bevoegde servicefaciliteit van Garmin in het land van aankoop of volgt u de instructies op support.garmin.com voor de garantieservice. Als u zich in de Verenigde Staten bevindt, kunt u ook bellen naar 1-800-800-1020. Als u gebruik wilt maken van de garantieservice buiten het land van aankoop, kan Garmin niet garanderen dat de onderdelen of producten voor reparatie of vervanging beschikbaar zijn, wegens verschillen in productaanbod en toepasselijke standaarden en wet- en regelgeving. In dat geval repareert of vervangt Garmin naar eigen oordeel en krachtens de geldende wetgeving uw product mogelijk met vergelijkbare Garmin producten en onderdelen, of dient u uw product naar een bevoegde Garmin servicefaciliteit te verzenden in het land van aankoop of naar een bevoegde Garmin servicefaciliteit in een ander land die uw product in behandeling kan nemen. 7 In dat geval draagt u zelf de verantwoordelijkheid voor conformiteit met alle toepasselijke import-

en exportwet- en regelgeving en dient u zelf alle douanekosten, btw, verzendkosten en andere extra belastingen en kosten te betalen. In sommige gevallen kunnen Garmin en haar distributeurs uw toestel niet in behandeling nemen in een ander land dan het land van aankoop of een gerepareerd of vervangen product aan u retourneren in dat land, wegens toepasselijke standaarden en wet- en regelgeving in dat land. Aankopen via onlineveilingen: Producten die zijn aangekocht via onlineveilingen komen volgens de garantie niet in aanmerking voor kortingen en andere aanbiedingen van Garmin. Aankoopbevestigingen van onlineveilingen worden niet geaccepteerd als garantiebewijs. Om gebruik te kunnen maken van de garantieservice, is de oorspronkelijke of een kopie van de aankoopnota vereist van de winkel waar u het systeem hebt gekocht. Garmin vervangt geen onderdelen van pakketten die zijn aangeschaft via een onlineveiling. Internationale aankopen: Distributeurs buiten de Verenigde Staten verstrekken mogelijk een aparte garantie voor toestellen die buiten de Verenigde Staten zijn aangeschaft. Dit kan per land verschillen. Indien van toepassing wordt deze garantie verstrekt door de lokale binnenlandse distributeur die ook lokaal service voor het toestel verleent. Garanties door distributeurs zijn alleen geldig in het gebied waarvoor de distributie is bedoeld. Watersportgarantiebeleid: Bepaalde watersportproducten van Garmin hebben in bepaalde regio's een langere garantieperiode en aanvullende voorwaarden. Ga naar www.garmin.com

/support/warranty_marine voor meer informatie en om na te gaan of uw product onder het Watersportgarantiebeleid van Garmin valt. VIGTIGE SIKKERHEDS- OG PRODUKTINFORMATIONER ADVARSEL Hvis de flgende advarsler ignoreres, kan det resultere i ulykker eller sammenstd med dd eller alvorlige personskader til flge. Advarsler for marine betjening Du er ansvarlig for sikker og forsigtig betjening af dit fartj. Enheden er et vrktj, der forger dine muligheder for at betjene dit fartj. Enheden fritager dig ikke for ansvaret for sikker betjening af dit fartj. Undg navigationsmssige farer, og lad aldrig manvrepulten vre ubemandet. Brug kun denne enhed som en navigationshjlp. Brug ikke enheden til forml, der krver prcise mlinger af retning, afstand, position eller topografi. Vr altid parat til omgende at overtage styringen af fartjet. Udvis forsigtighed i nrheden af farer i vandet som f.eks. kajer, ple og andre fartjer. Hvis enheden har navigationsegenskaber, br du, nr du navigerer, omhyggeligt sammenholde de oplysninger, der vises p enheden, med alle tilgngelige navigationskilder, bl.a. oplysninger fra synsindtryk, lokale regler for vandveje og kort. Du skal for sikkerhedens skyld altid lse evt. uoverensstemmelser eller sprgsml, fr du fortstter navigationen. Hvis enheden anvender kort, br du kun bruge det elektroniske kort i enheden til at lette brugen af autoriserede kort, ikke til at erstatte dem. Officielle kort og oplysninger til sfarten indeholder alle de oplysninger, der er ndvendige for sikker navigation. Dybdedata fra dette produkt, hvis sdanne er tilgngelige, m ikke bruges som primr metode til at undg grundstdning eller kollision. Suppler dybdedata-aflsninger med information fra relevante papirkort og visuelle indtryk. Styr altid fartjet ved lav hastighed, hvis du har mistanke om lavt vand eller undervandsobjekter. Hvis denne advarsel overses, kan det medfre beskadigelse af fartjet eller personskader. Hvis enheden har mulighed for videoindgang, m du ikke forsge at betjene eller se video, mens du betjener eller navigerer fartjet. Hvis du betjener eller ser video, mens fartjet er i bevgelse, kan det forrsage ulykker eller sammenstd med materiel skade, alvorlig personskade eller dd til flge. Advarsel om hreskade Hvis du lytter til stereoanlgget ved hj lydstyrke, risikerer du at beskadige din hrelse. BEMRK Hvis den flgende advarsel ignoreres, kan det resultere i personskade eller materielskade, eller det kan forringe enhedens funktionsdygtighed. Bemrkninger vedrrende batteri Kontakt din lokale genbrugsstation for at f oplysninger om korrekt bortskaffelse af enheden/

batteriet i overensstemmelse med gldende love og regulativer. GPS-meddelelse Navigationsenhedens performance kan forringes, hvis du bruger den i nrheden af en enhed, der anvender et terrestrisk bredbndsnetvrk, som opererer i nrheden af de frekvenser, der anvendes af et GNSS-system (Global Navigation Satellite System), for eksempel GPS-tjenesten

(Global Positioning Service). Brug af sdanne enheder kan forringe modtagelsen af GNSS-

signaler. Miljvenlige produktprogrammer Oplysninger om Garmin produktgenanvendelsesprogrammet og WEEE, RoHS, REACH og andre overvgningsprogrammer kan findes p www.garmin.com/aboutGarmin/environment. Overensstemmelseserklring Garmin erklrer hermed, at dette produkt overholder direktivet 2014/53/EU. Du kan se hele EU-

overensstemmelseserklringen p flgende internetadresse: www.garmin.com/compliance. Information om kortdata Garmin anvender en kombination af officielle og private datakilder. Nsten alle datakilder indeholder nogle unjagtige eller ufuldstndige data. I visse lande er fuldstndig og njagtig kortinformation enten ikke tilgngelig, eller den er uforholdsmssigt dyr. Begrnset garanti DENNE BEGRNSEDE GARANTI GIVER DIG BESTEMTE JURIDISKE RETTIGHEDER, OG DU KAN HAVE ANDRE JURIDISKE RETTIGHEDER, SOM VARIERER FRA LAND TIL LAND

(ELLER FRA DELSTAT TIL DELSTAT ELLER FRA PROVINS TIL PROVINS). GARMIN UDELUKKER, BEGRNSER ELLER SUSPENDERER IKKE ANDRE JURIDISKE RETTIGHEDER, SOM DU MTTE HAVE I DIT LAND (ELLER DIN DELSTAT ELLER PROVINS). HVIS DU VIL OPN FULDT KENDSKAB TIL DINE RETTIGHEDER, SKAL DU SE LOVENE I DIT LAND, DIN DELSTAT ELLER DIN PROVINS. Produkter, der ikke er flyverelaterede, garanteres at vre fri for fejl og mangler i materialer og udfrelse i t r fra kbsdatoen. I denne periode vil Garmin efter eget valg reparere eller udskifte alle komponenter, der ikke fungerer ved normal brug. Sdanne reparationer eller udskiftninger foretages uden beregning for kunden, hvad angr reservedele og arbejdsln, mens kunden er ansvarlig for eventuelle transportomkostninger. Denne begrnsede garanti dkker ikke: (i) kosmetiske skader som f.eks. ridser, skrammer og buler; (ii) forbrugsartikler som f.eks. batterier, medmindre der er opstet produktskader pga. en defekt i materialer eller udfrelse; (iii) skader forrsaget af ulykker, forkert brug, misbrug, vand, oversvmmelse, brand eller andre naturkatastrofer eller udefra kommende rsager; (iv) skader pga. service, der er udfrt af en person, som ikke er en autoriseret serviceudbyder for Garmin; (v) skader p et produkt, som er blevet modificeret eller ndret uden skriftlig tilladelse fra Garmin; eller (vi) skader p et produkt, som er blevet sluttet til strm- og/eller datakabler, der ikke kommer fra Garmin. Garmin forbeholder sig desuden ret til at afvise garantikrav angende produkter eller tjenester, der erhverves og/eller bruges i modstrid med lovgivningen i noget land. Garmin navigationsprodukter er beregnet til kun at blive brugt som et rejsehjlpemiddel og m ikke anvendes til noget forml, som krver njagtig mling af retning, afstand, position eller topografi. Garmin udsteder ingen garanti for, at kortdataene er njagtige eller komplette. Denne begrnsede garanti glder desuden ikke for, og Garmin ptager sig ikke ansvar for, eventuel forringelse i performance af Garmin navigationsprodukter, der skyldes brug i nrheden 8 af et hndst eller en anden enhed, der anvender et terrestrisk bredbndsnetvrk, som opererer p frekvenser i nrheden af dem, der anvendes af et GNSS-system (Global Navigation Satellite System) som f.eks. GPS-tjenesten (Global Positioning Service). Brug af sdanne enheder kan forringe modtagelsen af GNSS-signaler. I DEN UDSTRKNING, DET ER MULIGT I HENHOLD TIL GLDENDE LOV, ER GARANTIERNE OG MISLIGHOLDELSESBEFJELSERNE I DENNE BEGRNSEDE GARANTI UDTMMENDE OG TRDER I STEDET FOR, OG GARMIN FRASKRIVER SIG UDTRYKKELIGT, ALLE ANDRE GARANTIER OG MISLIGHOLDELSESBEFJELSER, UANSET OM DE ER UDTRYKKELIGE, STILTIENDE, FORORDNEDE ELLER OPSTR P ANDEN VIS, HERUNDER, MEN IKKE BEGRNSET TIL, ENHVER UNDERFORSTET GARANTI FOR, AT PRODUKTET ER KURANT ELLER EGNET TIL SRLIGE FORML, LOVMSSIGE MISLIGHOLDELSESBEFJELSER ELLER ANDET. DENNE BEGRNSEDE GARANTI GIVER DIG BESTEMTE JURIDISKE RETTIGHEDER, OG DU KAN HAVE ANDRE JURIDISKE RETTIGHEDER, SOM VARIERER FRA LAND TIL LAND OG FRA DELSTAT TIL DELSTAT. HVIS UNDERFORSTEDE GARANTIER IKKE KAN FRASKRIVES IFLGE LOVENE I DIT LAND ELLER DIN DELSTAT, ER VARIGHEDEN AF SDANNE GARANTIER BEGRNSET TIL VARIGHEDEN AF DENNE BEGRNSEDE GARANTI. NOGLE LANDE (OG DELSTATER OG PROVINSER) TILLADER IKKE BEGRNSNING I VARIGHEDEN AF EN UNDERFORSTET GARANTI, HVORFOR OVENSTENDE BEGRNSNING MULIGVIS IKKE GLDER FOR DIG. UNDER INGEN OMSTNDIGHEDER ER GARMIN ANSVARLIG FOR KRAV I FORBINDELSE MED BRUD P GARANTI I FORBINDELSE MED NOGEN EKSTRASKADER, SRLIGE SKADER, INDIREKTE SKADER ELLER FLGESKADER, HVAD ENTEN DE SKYLDES BRUG, MISBRUG ELLER MANGLENDE EVNE TIL BRUG AF DETTE PRODUKT ELLER FEJL OG MANGLER VED PRODUKTET. NOGLE LANDE (OG DELSTATER OG PROVINSER) TILLADER IKKE UDELUKKELSE AF ANSVARET FOR FLGESKADER OG HNDELIGE SKADER, S DET ER IKKE SIKKERT, AT OVENSTENDE BEGRNSNINGER GLDER FOR DIG. Hvis du i lbet af garantiperioden anmelder et krav om garantiservice i overensstemmelse med denne begrnsede garanti, vil Garmin efter eget valg: (i) reparere enheden ved hjlp af nye dele eller brugte dele, der lever op til Garmins kvalitetsstandarder, (ii) ombytte enheden med en ny enhed eller en renoveret enhed, der overholder Garmins kvalitetsstandarder, eller (iii) ombytte enheden mod fuld refusion af kbsprisen. DEN VALGTE LSNING ER DIN ENESTE LSNING P ETHVERT BRUD P GARANTIEN. Reparerede eller ombyttede enheder har 90 dages garanti. Hvis den oprindelige garanti for den enhed, der sendes ind, stadig glder, er den nye garantiperiode p 90 dage eller til slutningen af den oprindelige 1-rige garantiperiode den lngste af disse perioder er gldende. Fr du anmoder om garantiservice, skal du g til og gennemse de onlineressourcer til hjlp, der er tilgngelige p support.garmin.com. Hvis din enhed stadig ikke fungerer korrekt, efter at du har brugt disse ressourcer, skal du kontakte en Garmin autoriseret servicefacilitet i det land, hvor du oprindeligt har kbt enheden, eller flge instruktionerne p support.garmin.com for at f garantiservice. Hvis du befinder dig i USA, kan du ogs ringe til 1-800-800-1020. Hvis du anmoder om garantiservice uden for det land, hvor du oprindeligt kbte din enhed, kan Garmin ikke garantere, at de dele og produkter, der skal til for at reparere eller ombytte dit produkt, vil vre tilgngelige, p grund af forskelle i produkttilbud og gldende standarder, love og regulativer. I s fald kan Garmin efter eget valg og i henhold til gldende love reparere eller ombytte dit produkt med sammenlignelige Garmin produkter og dele eller krve, at du sender dit produkt til en Garmin autoriseret servicefacilitet i det land, hvor du oprindeligt kbte enheden, eller til en Garmin autoriseret servicefacilitet i et andet land, der kan yde service p dit produkt. I s fald vil du vre ansvarlig for at overholde alle gldende import- og eksportlove og -

regulativer samt for betaling af told, moms, forsendelsesafgifter og andre associerede skatter og afgifter. I nogle tilflde kan Garmin og dets forhandlere muligvis ikke yde service p dit produkt i et land uden for det land, hvor du oprindeligt kbte enheden, eller returnere et repareret eller ombyttet produkt til dig i det pgldende land p grund af gldende standarder, love eller regulativer i det pgldende land. Kb fra onlineauktioner: Produkter, som er kbt gennem onlineauktioner, berettiger ikke til rabatter eller andre srtilbud fra Garmin garantidkning. Onlineauktionsbekrftelser accepteres ikke som bevis p krav om garanti. Der krves en original faktura fra forhandleren

(eller en kopi af den) for at f garantiservice. Garmin vil ikke erstatte manglende dele fra en pakke, der er kbt p en onlineauktion. Internationale kb: Der udstedes muligvis en separat garanti af internationale forhandlere for enheder, som er kbt uden for USA afhngigt af landet. Hvis en sdan garanti findes, gives den af den lokale forhandler i landet, og denne forhandler yder lokal service til din enhed. Forhandlergarantier glder kun i de tilsigtede distributionsomrder. Marine Garantipolitik: Visse Garmin Marineprodukter i visse omrder har en lngere garantiperiode og ekstra vilkr og betingelser. G til www.garmin.com/support/warranty_marine for at f yderligere oplysninger og for at se, om dit produkt er omfattet af Garmin Marine Garantipolitik. TRKEIT TURVALLISUUS- JA TUOTETIETOJA VAROITUS Seuraavien varoitusten laiminlynti voi aiheuttaa onnettomuuden tai trmyksen, joka voi johtaa kuolemaan tai vakavaan loukkaantumiseen. Veneilykytn varoitukset Olet vastuussa aluksen turvallisesta ja jrkevst kytst. Tm laite on tykalu, joka tehostaa aluksen kytt. Laite ei poista vastuutasi aluksen turvallisesta kytst. Vlt navigoinnin vaaratilanteet lk jt ruoria ilman valvontaa. Laite on tarkoitettu ainoastaan navigoinnin avuksi. l yrit kytt laitetta mihinkn kytttarkoitukseen, joka edellytt tarkkaa suunnan, etisyyden, paikan tai topografian mittausta. Ole aina valmiina vaihtamaan manuaaliseen ohjaukseen. Ole varovainen, kun vedess on esteit, kuten laitureita, paalutuksia ja muita aluksia. Jos laitteessa on navigointiominaisuus, vertaa laitteen antamia tietoja navigoinnin aikana kaikkiin muihin mahdollisiin navigointikeinoihin, kuten visuaaliset kohteet, paikalliset vesitiesnnt ja kartat. Turvallisuussyist kaikki eroavuudet ja epselvyydet on selvitettv ennen navigoinnin jatkamista. Jos laite kytt karttoja, kyt laitteen shkist karttaa ainoastaan valtionjohdon virallisten karttojen apuna, ei korvikkeena. Viralliset kartat ja ilmoitukset merenkulkijoille sisltvt kaikki turvalliseen navigointiin tarvittavat tiedot. Jos laite antaa syvyystietoja, niit ei saa kytt ensisijaisena pohjakosketuksen tai trmyksen estmistapana. Tydenn syvyystietolukemia asianmukaisten paperikarttojen ja visuaalisten merkkien tiedoilla. Etene aina hitaalla nopeudella, jos epilet edess olevan matalaa vett tai vedenalaisia kohteita. Tmn varoituksen laiminlyminen voi aiheuttaa aluksen vioittumisen tai henkilvahingon. Jos laitteessa on videotulo-ominaisuus, l yrit kytt tai katsoa videokuvaa, kun ohjaat alusta. Videokuvan kyttminen tai katsominen aluksen ollessa liikkeess saattaa aiheuttaa onnettomuuden tai trmyksen, joka puolestaan voi vaurioittaa omaisuutta tai aiheuttaa vakavan loukkaantumisen tai kuoleman. Kuulovauriovaroitus Stereoiden kuuntelu suurella nenvoimakkuudella voi vahingoittaa kuuloasi. HUOMAUTUS Seuraavan ilmoituksen laiminlynti voi aiheuttaa vammoja, vaurioittaa omaisuutta tai heikent laitteen toimintaa. Akkuilmoitus Hvit laite/akut/paristot paikallisten jtehuoltomrysten mukaisesti. GPS-ilmoitus Navigointilaitteen suorituskyky saattaa heiket, jos laitetta kytetn lhell laitteita, joiden kyttmt maanpllisen laajakaistaverkon taajuudet ovat lhell taajuuksia, joita kytetn maailmanlaajuisissa navigointijrjestelmiss (Global Navigation Satellite System, GNSS), kuten GPS (Global Positioning Service) -jrjestelmss. Niden laitteiden kytt saattaa heikent GNSS-signaalien vastaanottoa. Tuotteiden ympristohjelmat Tietoja yhtin Garmin tuotteiden kierrtysohjelmasta sek WEEE-, RoHS-, REACH-ohjelmista ja muista ohjelmista on osoitteessa www.garmin.com/aboutGarmin/environment. Vaatimustenmukaisuusvakuutus Garmin vakuuttaa tten, ett tm tuote on direktiivin 2014/53/EU mukainen. EU:n vaatimustenmukaisuusvakuutuksen koko teksti on nhtviss osoitteessa www.garmin.com

/compliance. Tietoa karttatiedoista Garmin kytt sek julkishallinnon ett yksityisi tietolhteit. Lhes kaikissa tietolhteiss on joitakin vri tai puutteellisia tietoja. Joistakin maista ei ole saatavissa tydellisi ja tarkkoja karttatietoja, tai ne ovat erittin kalliita. Rajoitettu takuu TM RAJOITETTU TAKUU ANTAA KYTTJLLE TIETTYJ LAIN MUKAISIA OIKEUKSIA, JOIDEN LISKSI KYTTJLL SAATTAA OLLA MUITA OIKEUKSIA, JOTKA VAIHTELEVAT MAAN JA ALUEEN MUKAAN. GARMIN EI SULJE POIS, RAJOITA EIK KESKEYT MUITA LAIN MUKAISIA OIKEUKSIA, JOITA KYTTJLL SAATTAA OLLA ASUINMAANSA TAI ALUEENSA MUKAAN. KYTTJ VOI SAADA LISTIETOJA ASIASTA TUTKIMALLA MAANSA TAI ALUEENSA LAKEJA. Muilla kuin ilmailutuotteilla on vuoden materiaalin ja tyn virheettmyystakuu ostopivst alkaen. Tmn jakson aikana Garmin valintansa mukaan joko korjaa tai vaihtaa osat, jotka vioittuvat normaalissa kytss. Nm korjaukset ja vaihdot ovat asiakkaalle maksuttomia osien ja tyn osalta. Asiakas on vastuussa kuljetuskuluista. Tm rajoitettu takuu ei koske (i) kosmeettisia vaurioita, kuten naarmut, kolhut ja lommot, (ii) kuluvia osia, kuten akut, ellei vaurio ole aiheutunut materiaali- tai valmistusviasta, (iii) vahinkoja, jotka aiheutuvat onnettomuudesta, vrinkytst, virheellisest kytst tai veden, tulvan, tulen tai muun luonnonilmin aiheuttamista vaurioista, (iv) vaurioita, jotka aiheutuvat muun kuin valtuutetun Garmin huoltohenkiln tekemist huoltotoimenpiteist, (v) ilman yhtin Garmin kirjallista lupaa muokattuun tai muutettuun tuotteeseen aiheutuneita vaurioita tai (vi) muilla kuin yhtin Garmin toimittamilla virta- ja/tai datakaapeleilla liitetyn laitteen vaurioita. Lisksi Garmin pidtt oikeuden hylt takuuvaatimukset sellaisten tuotteiden tai palveluiden kohdalla, jotka on hankittu ja/tai joita on kytetty mink tahansa valtion lakien vastaisesti.Yrityksen Garmin navigointituotteet on tarkoitettu kytettviksi vain matkustamisen apuna eik niit tule kytt mihinkn sellaiseen tarkoitukseen, joka edellytt tarkkaa suunnan, etisyyden, sijainnin tai topografian mittausta. Garmin ei takaa karttatietojen tarkkuutta tai kattavuutta. Lisksi tm rajoitettu takuu ei kata eik Garmin korvaa Garmin navigointituotteiden suorituskyvyn heikkenemist, joka johtuu siit, ett tuotetta on kytetty lhell matkapuhelinta tai muuta laitetta, jonka kyttmt maanpllisen laajakaistaverkon taajuudet ovat lhell taajuuksia, joita kytetn maailmanlaajuisissa navigointisatelliittijrjestelmiss (GNSS, Global Navigation Satellite System), kuten GPS (Global Positioning Service) -jrjestelmss. Niden laitteiden kytt saattaa heikent GNSS-signaalien vastaanottoa. SIIN MRIN KUIN SOVELTUVA LAKI ENIMMILLN SALLII, TSS RAJOITETUSSA TAKUUSSA ESITETYT TAKUUT JA HYVITYKSET OVAT POISSULKEVIA JA NE KORVAAVAT, JA GARMIN NIMENOMAISESTI KIELT, KAIKKI MUUT NIMENOMAISET, OLETETUT, LAKISTEISET JA MUUT TAKUUT JA HYVITYKSET, MUKAAN LUKIEN MUUN MUASSA OLETETUT TAKUUT MYYNTIKELPOISUUDESTA TAI SOPIVUUDESTA TIETTYYN TARKOITUKSEEN SEK LAKISTEISET HYVITYKSET. TM RAJOITETTU TAKUU ANTAA KYTTJLLE TIETTYJ LAIN MUKAISIA OIKEUKSIA, JOIDEN LISKSI KYTTJLL SAATTAA OLLA MUITA OIKEUKSIA, JOTKA VAIHTELEVAT MAAN JA ALUEEN MUKAAN. JOS SANOUTUMINEN IRTI OLETETUISTA TAKUISTA EI OLE MAAN TAI ALUEEN LAKIEN MUKAAN MAHDOLLISTA, KYSEISTEN TAKUIDEN KESTO RAJOITTUU TMN RAJOITETUN TAKUUN KESTOON. TIETYILL LAINKYTTALUEILLA EI SALLITA EPSUORIEN TAKUIDEN KESTON RAJOITTAMISTA, JOTEN EDELL MAINITTU RAJOITUS EI EHK KOSKE KAIKKIA KYTTJI. GARMIN EI OLE MISSN TILANTEESSA VASTUUSSA TAKUURIKKOMUKSEEN LIITTYVISS VAATEISSA VLILLISIST, ERITYISIST, EPSUORISTA TAI SEURANNAISISTA VAHINGOISTA, RIIPPUMATTA SIIT, JOHTUVATKO NE TUOTTEEN VRINKYTST, VIRHEELLISEST KYTST, TAITAMATTOMASTA KYTST VAI TUOTTEEN PUUTTEISTA. JOILLAKIN LAINKYTTALUEILLA EI SALLITA VLILLISTEN TAI SEURANNAISTEN VAHINKOJEN POIS RAJAAMISTA TAI RAJOITTAMISTA, JOTEN YLL OLEVAT RAJOITUKSET EIVT EHK KOSKE KAIKKIA KYTTJI. Jos kyttj toimittaa tmn rajoitetun takuun mukaisen vaatimuksen takuuhuollosta takuuaikana, Garmin harkintansa mukaan: (i) korjaa laitteen kytten uusia tai kytettyj osia, jotka tyttvt yrityksen Garmin laatuvaatimukset, (ii) korvaa laitteen uudella tai kunnostetulla laitteella, joka tytt yrityksen Garmin laatuvaatimukset, tai (iii) hyvitt laitteen koko ostohinnan. TM HYVITYS ON AINOA KYTTJN SAAMA HYVITYS TAKUURIKKOMUKSESTA. Korjatuilla tai vaihdetuilla laitteilla on 90 pivn takuu. Jos laitteen alkuperinen takuu on viel voimassa, uusi takuu kest 90 piv tai alkuperisen yhden vuoden takuun loppuun sen mukaan, kumpaan on enemmn aikaa. Ennen kuin kyttj hankkii takuuhuoltoa, hnen kannattaa tutustua ohjeresursseihin osoitteessa support.garmin.com. Jos laite ei toimi oikein, kun kyttj on hydyntnyt mainittuja resursseja, hnen on otettava yhteys yrityksen Garmin valtuuttamaan huoltoon alkuperisess ostomaassa tai hankittava takuuhuoltoa osoitteessa support.garmin.com olevien ohjeiden mukaisesti. Jos kyttj asuu Yhdysvalloissa, hn voi mys soittaa numeroon 1-800-800-1020. Jos kyttj hankkii takuuhuoltoa muualla kuin alkuperisess ostomaassa, Garmin ei voi taata, ett tuotteen korjaamiseen tai vaihtamiseen tarvittavat osat ja tuotteet ovat saatavilla, koska tuotevalikoima sek sovellettavat standardit, lait ja sdkset vaihtelevat maittain. Siin tapauksessa Garmin voi harkintansa ja sovellettavien lakien mukaan korjata tuotteen tai vaihtaa sen vastaaviin Garmin tuotteisiin ja osiin tai edellytt, ett kyttj toimittaa tuotteen yrityksen Garmin valtuuttamaan huoltoon alkuperisess ostomaassa tai toisessa maassa sijaitsevaan yrityksen Garmin valtuuttamaan huoltoon, joka voi huoltaa tuotteen. Siin tapauksessa kyttj vastaa kaikkien sovellettavien tuonti- ja vientilakien ja -sdsten noudattamisesta sek kaikista tullimaksuista, veroista, toimitusmaksuista ja muista maksuista. Joissakin tapauksissa Garmin ja sen jlleenmyyjt eivt vlttmtt voi huoltaa tuotetta muualla kuin alkuperisess ostomaassa tai palauttaa korjattua tai vaihdettua tuotetta kyttjlle kyseisess maassa maan sovellettavien standardien, lakien tai sdsten vuoksi. Verkkohuutokauppaostokset: verkkohuutokaupoista ostetut tuotteet eivt ole ostohyvitysten tai muiden yhtin Garmin takuiden erikoistarjousten piiriss. Verkkohuutokauppojen vahvistukset eivt ky takuukuitista. Takuupalvelun saamisen ehtona on vhittismyyjlt saatu alkuperinen ostokuitti tai sen kopio. Garmin ei korvaa verkkohuutokaupasta hankituista pakkauksista puuttuvia osia. Kansainvliset ostot: Yhdysvaltain ulkopuolella kansainvlisilt jlleenmyyjilt ostettuja jrjestelmi varten voi maan mukaan olla erillinen takuu. Mahdollisen takuun mynt paikallinen maakohtainen jakelija, joka tarjoaa paikallista huoltoa laitteelle. Jakelijan takuut ovat voimassa ainoastaan tarkoitetulla jakelualueella. Veneilytuotteiden takuukytnt: Tietyill yhtin Garmin veneilytuotteilla on tavallista pitempi takuuaika tietyill alueilla, ja tllin kytss on mys liskyttehtoja. Tarkista osoitteesta www.garmin.com/support/warranty_marine, onko tuotteesi yhtin Garmin veneilytuotteiden takuukytnnn piiriss. VIKTIG SIKKERHETS- OG PRODUKTINFORMASJON ADVARSEL Hvis du ikke tar hensyn til flgende advarsler, kan det fre til ulykke eller kollisjon med ddsfall eller alvorlig personskade som flge. Advarsler om bruk p sjen Du er ansvarlig for sikker og forsvarlig betjening av fartyet. Denne enheten er et verkty som forbedrer betjeningen av fartyet. Denne enheten unntar deg ikke ansvaret for styre fartyet p en trygg og sikker mte. Unng navigasjonsfarer, og la aldri roret st ubemannet. Bruk denne enheten utelukkende som navigeringshjelp. Ikke bruk enheten til andre forml som krever nyaktig mling av retning, avstand, beliggenhet eller topografi. Vr alltid klar til ta kontroll over fartyet. Vr forsiktig i nrheten av farer i vannet, for eksempel brygger, pleverk og andre farty. Hvis enheten har muligheter for navigasjon, m du sammenligne informasjon som vises p enheten, nye med alle tilgjengelige navigasjonskilder, inkludert informasjon fra egne observasjoner, lokale bestemmelser og begrensninger for vannveier og kart under navigasjonen. Av sikkerhetsgrunner m du alltid finne ut av avvik eller sprsml du har, fr du fortsetter navigere. Hvis enheten bruker kart, skal det elektroniske kartet p enheten bare brukes som et hjelpemiddel. Det skal ikke erstatte bruk av offentlig autoriserte kart. Offentlig autoriserte kart og meldinger inneholder all ndvendig informasjon for trygg navigering. Hvis enheten gir dybdedata, skal du ikke bruke disse dataene som hovedhjelpemiddel for forhindre grunnstting eller kollisjon. Supplementer dybdedataavlesningene med informasjon fra relevante papirkart og visuelle indikatorer. La alltid fartyet holde lav hastighet hvis du tror at vannet kan vre grunt, eller at det kan vre gjenstander under vann. Hvis du ikke tar hensyn til denne advarselen, kan det fre til skade p fartyet eller personskade. Hvis enheten har videoinnganger, m du ikke betjene eller se p video samtidig som du betjener eller navigerer fartyet. Hvis du betjener eller ser p video mens fartyet er i bevegelse, kan det forrsake en ulykke eller kollisjon som frer til skader p eiendeler, alvorlige personskader eller ddsfall. Advarsel om hrselsskader Hvis du har for hyt volum p stereoanlegget, kan du f hrselsskader. LES DETTE Hvis du ikke tar hensyn til flgende merknad, kan fre til personskader eller materielle skader eller pvirke enhetens funksjonalitet. Merknad om batterier Kontakt den lokale avfallsstasjonen for kassere enheten/batteriene i henhold til lokale lover og regler. GPS-merknad Hvis du bruker navigasjonsenheten i nrheten av en enhet som bruker et bakkebundet bredbndnettverk med driftsfrekvenser som likner frekvensene til globale navigasjonssatellittsystemer (GNSS), for eksempel Global Positioning Service (GPS), kan du oppleve at navigasjonsenheten har redusert ytelse. Bruken av slike enheter kan pvirke mottaket av GNSS-signaler. Miljprogrammer for produkter Du finner mer informasjon om produktresirkuleringsprogrammet til Garmin samt WEEE, RoHS, REACH og andre samsvarsprogrammer p www.garmin.com/aboutGarmin/environment. Samsvarserklring Garmin erklrer herved at dette produktet er i samsvar med EU-direktiv 2014/53/EU. EU-

samsvarserklringen er tilgjengelig i sin helhet p flgende nettadresse: www.garmin.com

/compliance. Kartdatainformasjon Garmin bruker en kombinasjon av offentlige og private datakilder. S si alle datakilder inneholder noen uriktige eller ufullstendige data. I noen land er fullstendig og nyaktig kartinformasjon enten ikke tilgjengelig eller uforholdsmessig dyr. Begrenset garanti DENNE BEGRENSEDE GARANTIEN GIR DEG BESTEMTE JURIDISKE RETTIGHETER, OG DU KAN OGS HA ANDRE RETTIGHETER SOM VARIERER FRA DELSTAT TIL DELSTAT

(ELLER ETTER LAND ELLER PROVINS). GARMIN VIL IKKE EKSKLUDERE, BEGRENSE ELLER OPPHEVE ANDRE JURIDISKE RETTIGHETER DU KAN HA I HENHOLD TIL LOVENE I DELSTATEN (ELLER LANDET ELLER PROVINSEN). SE LOVENE I DELSTATEN DIN, LANDET DITT ELLER PROVINSEN DIN FOR F EN FULLSTENDIG FORSTELSE AV RETTIGHETENE DINE. Produkter som ikke har med flyteknikk gjre, garanteres vre feilfrie med hensyn til materiell og utfrelse i ett r fra kjpsdatoen. I denne perioden vil Garmin, etter eget valg, reparere eller skifte ut enhver komponent som ikke fungerer ved normal bruk. Slike reparasjoner eller utskiftinger utfres kostnadsfritt for kunden, bde nr det gjelder deler og arbeid, forutsatt at kunden selv dekker eventuelle transportkostnader. Denne begrensede garantien gjelder ikke: (i) kosmetiske skader, for eksempel riper, hakk og bulker; (ii) forbruksdeler, for eksempel batterier, med mindre produktet har blitt skadet p grunn av en defekt i materialet eller utfrelsen; (iii) skade som skyldes uhell, misbruk, feil bruk, vann, flom, brann eller andre naturhendelser eller eksterne rsaker; (iv) skade som skyldes service som er utfrt av personer som ikke er autoriserte serviceleverandrer for Garmin; eller (v) skade p et produkt som har blitt endret uten skriftlig tillatelse fra Garmin, eller (vi) skade p et produkt som er koblet til strm- og/eller datakabler fra andre leverandrer enn Garmin. I tillegg forbeholder Garmin seg retten til nekte garantikrav mot produkter eller tjenester som er innhentet og/eller som brukes i strid med lovene i et hvilket som helst land.Navigasjonsprodukter fra Garmin er kun beregnet p bruk som reisehjelp og skal ikke brukes til eventuelle forml som krever nyaktig mling av retning, avstand, posisjon eller topografi. Garmin gir ingen garantier for nyaktigheten eller fullstendigheten til kartdataene. Denne begrensede garantien gjelder ikke, og Garmin er ikke ansvarlig for, redusert ytelse p Garmin navigasjonsprodukter som flge av bruk i nrheten av hndsett eller andre enheter som bruker bakkebundne nettverk med driftsfrekvenser som likner frekvenser som brukes av globale navigasjonssatellittsystemer for navigering (GNSS), for eksempel Global Positioning Service

(GPS). Bruken av slike enheter kan pvirke mottaket av GNSS-signaler. I DEN GRAD DET ER TILLATT AV GJELDENDE LOV, ER GARANTIENE OG RETTSMIDLENE SOM BESKRIVES I DENNE BEGRENSEDE GARANTIEN EKSKLUSIVE, OG ERSTATTER ALLE ANDRE GARANTIER OG RETTSMIDLER, OG GARMIN FRASKRIVER SEG UTTRYKKELIG ALLE ANDRE GARANTIER OG RETTSMIDLER, ENTEN DE ER UTTRYKTE, UNDERFORSTTTE, LOVPLAGTE ELLER ANNET, INKLUDERT, MEN IKKE BEGRENSET TIL, ALLE UNDERFORSTTTE GARANTIER FOR SALGBARHET ELLER EGNETHET TIL NOE BESTEMT FORML, LOVPLAGT RETTSMIDDEL ELLER ANNET. DENNE BEGRENSEDE GARANTIEN GIR DEG BESTEMTE JURIDISKE RETTIGHETER, OG DU KAN OGS HA ANDRE RETTIGHETER SOM VARIERER FRA DELSTAT TIL DELSTAT OG FRA LAND TIL LAND. HVIS UNDERFORSTTTE GARANTIER IKKE KAN FRASKRIVES IFLGE LOVENE I DELSTATEN ELLER LANDET, ER SLIKE GARANTIER BEGRENSET I VARIGHET 9 TIL DENNE BEGRENSEDE GARANTIEN UTLPER. NOEN DELSTATER (OG LAND OG PROVINSER) TILLATER IKKE BEGRENSNINGER AV VARIGHETEN TIL EN UNDERFORSTTT GARANTI, OG DET ER DERFOR MULIG AT BEGRENSNINGENE OVENFOR IKKE GJELDER FOR DEG. UNDER INGEN OMSTENDIGHETER SKAL GARMIN HOLDES ANSVARLIG MED HENSYN TIL ET KRAV OM BRUDD P GARANTIEN FOR EVENTUELLE TILFELDIGE, SPESIELLE ELLER INDIREKTE SKADER ELLER FLGESKADER SOM SKYLDES BRUK, FEILAKTIG BRUK ELLER MANGLENDE EVNE TIL BRUKE PRODUKTET ELLER PRODUKTFEIL. NOEN DELSTATER (OG LAND OG PROVINSER) TILLATER IKKE ANSVARSFRASKRIVELSE VED TILFELDIGE SKADER OG FLGESKADER, OG DET ER DERFOR MULIG AT BEGRENSNINGENE OVENFOR IKKE GJELDER FOR DEG. Hvis du i garantiperioden sender inn et krav om service som dekkes av garantien i henhold til denne begrensede garantien, vil Garmin etter eget valg: (i) reparere enheten ved hjelp av nye eller brukte deler som mter kvalitetskravene til Garmin, (ii) erstatte enheten med en ny eller utbedret enhet som mter kvalitetskravene til Garmin, eller (iii) bytte enheten mot full refusjon av kjpesummen. DETTE RETTSMIDDELET VIL VRE DITT ENESTE OG EKSKLUSIVE RETTSMIDDEL VED EVENTUELLE GARANTIBRUDD. Reparerte eller erstattede enheter har en garanti p 90 dager. Hvis enheten som sendes inn, fortsatt er dekket av den opprinnelige garantien, gjelder den nye garantien i 90 dager eller til den opprinnelige garantien p ett r utlper, avhengig av hvilken av dem som varer lengst. Fr du ber om service som dekkes av garantien, kan du ske hjelp via de nettbaserte hjelperessursene p support.garmin.com. Hvis enheten fortsatt ikke fungerer etter at du har skt hjelp via disse ressursene, kan du kontakte et Garmin autorisert servicested i landet hvor du kjpte enheten, eller du kan flge instruksjonene p support.garmin.com for f service som dekkes av garantien. Hvis du befinner deg i USA, kan du ogs ringe 1-800-800-1020. Hvis du ber om service som dekkes av garantien utenfor landet hvor du kjpte enheten, kan ikke Garmin garantere at delene og produktene som kreves for reparere eller erstatte produktet ditt, er tilgjengelig som flge av ulikt produktutvalg og ulike gjeldende standarder, lover og regler. I slike tilfeller kan Garmin etter eget skjnn og i den grad gjeldende lovverk tillater det, reparere eller erstatte produktet ditt med tilsvarende Garmin produkter og deler eller kreve at du sender inn produktet ditt til et Garmin servicested i landet hvor du kjpte produktet eller til et Garmin autorisert servicested i et annet land som kan tilby deg service. Du blir da ansvarlig for overholde alle gjeldende lover og regler for import og eksport samt for betale tollgebyr, MVA, frakt og andre tilknyttede skatter og kostnader. I noen tilfeller kan Garmin og vre forhandlere vre ute av stand til tilby deg service av produktet ditt i et land utenfor landet hvor du kjpte produktet eller returnere et reparert eller erstattet produkt til deg i det landet som flge av gjeldende lover eller regler i det landet. Kjp p Internett-auksjoner: Produkter som er kjpt gjennom Internett-auksjoner, kvalifiserer ikke til rabatter eller andre spesialtilbud knyttet til garantidekning fra Garmin. Bekreftelser fra auksjoner p Internett godtas ikke som dokumentasjon i garantisaker. Det kreves en original eller kopi av kvitteringen fra det opprinnelige utsalgsstedet for at en reparasjon skal dekkes av garantien. Garmin vil ikke erstatte manglende komponenter fra en pakke som er kjpt gjennom en Internett-auksjon. Internasjonale kjp: En separat garanti kan gis av internasjonale distributrer for enheter som er kjpt utenfor USA, avhengig av landet. Hvis det er aktuelt, gis denne garantien av den lokale distributren, og denne distributren utfrer lokal service p enheten. Distributrgarantier er bare gyldige i omrdet for tiltenkt distribusjon. Garantiretningslinjer for maritime produkter: Enkelte maritime Garmin produkter i enkelte omrder har lengre garantiperiode og ytterligere vilkr og betingelser. G til www.garmin.com

/support/warranty_marine hvis du vil ha mer informasjon, og for se om produktet ditt er dekket av Garmin garantiretningslinjene for maritime produkter. VIKTIG SKERHETS- OCH PRODUKTINFORMATION VARNING Om du inte uppmrksammar fljande varningar kan det resultera i olyckor eller kollisioner som kan sluta med ddsfall eller allvarlig personskada. Varningar vid marin anvndning Du ansvarar fr att bten framfrs p ett skert och frnuftigt stt. Den hr enheten r ett verktyg som hjlper dig att hantera bten. Den hr enheten befriar dig inte frn ansvaret fr att framfra din bt skert. Undvik farlig navigering och lmna aldrig rodret utan uppsikt. Anvnd den hr enheten endast som navigationshjlp. Frsk inte att anvnda enheten fr ngot ndaml dr exakt mtning av riktning, avstnd, plats eller topografi krvs. Var alltid beredd p att snabbt terg till att styra bten. Var frsiktig nra faror i vattnet, till exempel hamnar, plverk och andra btar. Om enheten hanterar navigering ska du nr du navigerar noggrant jmfra den information som enheten visar med alla tillgngliga navigeringskllor, inklusive information frn visuella iakttagelser, lokala farvattensbestmmelser och -begrnsningar samt kartor. Fr skerhets skull br du lsa alla avvikelser eller frgor innan du fortstter att navigera. Om enheten anvnder kartor anvnder du det elektroniska sjkortet i enheten endast fr att underltta, inte erstta, anvndningen av godknda sjkort. Godknda sjkort och information till sjmn innehller all information som krvs fr att navigera p ett skert stt. Djupdata frn den hr produkten ska inte anvndas som det primra sttet att undvika grundsttningar och kollisioner. Komplettera djupdataavlsningar med information frn tillmpliga pappersdiagram och synliga indikatorer. Kr alltid bten med lg hastighet om du misstnker grunt vatten eller freml under vattenytan. Om denna varning inte fljs kan det leda till bt- och personskador. Om enheten har videoingngar ska du inte hantera eller titta p video medan du hanterar eller navigerar din bt. Om du hanterar eller tittar p video medan bten krs kan du orsaka en olycka eller krock som kan resultera i egendomsskador, allvarlig personskada eller dd. Varning fr hrselskador Om du lyssnar p stereon p hg volym kan din hrsel skadas. OBS!

Underltenhet att beakta fljande meddelande kan leda till personlig skada eller egendomsskada, och pverka enhetens funktionalitet negativt. Batterimeddelande Kontakta lokala avfallsmyndigheter fr information om var du kan kasta enheten/batterierna i enlighet med lokala lagar och bestmmelser. GPS-meddelande Navigeringsenhetens prestanda kan bli smre om du anvnder den i nrheten av enheter som anvnder markbundet bredbandsntverk nra de frekvenser som anvnds av Global Navigation Satellite System (GNSS), t.ex. Global Positioning Service (GPS). Anvndning av sdana enheter kan frsmra mottagningen av GNSS-signaler. Miljprogram fr produkter Information om Garmin produkttervinningsprogram och WEEE, RoHS, REACH och andra kompabilitetsprogram hittar du p www.garmin.com/aboutGarmin/environment. verensstmmelsefrklaring Hrmed intygar Garmin att denna produkt verensstmmer med kraven i direktivet 2014/53/EG. Den fullstndiga texten i EG-frklaringen om verensstmmelse finns p fljande internetadress:

www.garmin.com/compliance. 10 Information om kartdata Garmin anvnder en kombination av privata datakllor och datakllor frn myndigheter. S gott som alla datakllor innehller en del felaktiga eller ofullstndiga data. I vissa lnder r fullstndig och exakt kartinformation inte tillgnglig eller overkomligt dyr. Begrnsad garanti DENNA BEGRNSADE GARANTI GER DIG SPECIFIKA LAGLIGA RTTIGHETER, OCH DU KAN HA ANDRA LAGSTADGADE RTTIGHETER SOM KAN VARIERA FRN STAT TILL STAT (ELLER LAND ELLER REGION). GARMIN UTESLUTER INTE, BEGRNSAR ELLER DRAR IN ANDRA JURIDISKA RTTIGHETER DU KAN HA ENLIGT LAGARNA I DITT OMRDE (ELLER LAND ELLER REGION). FR EN FULLSTNDIG FRSTELSE AV DINA RTTIGHETER BR DU KONSULTERA LAGARNA I DITT LAND ELLER REGION. Icke-flygprodukter garanteras vara fria frn defekter i material och utfrande i ett r frn inkpsdatumet. Under denna tid kommer Garmin att efter eget gottfinnande reparera eller erstta komponenter som inte fungerar vid normal anvndning. Sdana reparationer eller ersttningar grs utan ngon avgift fr kunden vad gller delar eller arbete, frutsatt att kunden str fr alla transportkostnader. Den hr begrnsade garantin gller inte fr: (i) kosmetiska skador, t.ex. repor, hack och bulor, (ii) frbrukningsdelar, t.ex. batterier, svida inte produktskadan uppsttt p.g.a. defekter i material eller arbete, (iii) skada orsakad av olycka, missbruk, vatten, versvmning, brand eller andra naturhndelser eller yttre orsaker, (iv) skada orsakad av service utfrd av ngon som inte r behrig serviceleverantr t Garmin, (v) skada p en produkt som har modifierats eller ndrats utan skriftligt tillstnd frn Garmin, eller (vi) skada p en produkt som har anslutits till strm- och/eller datakablar som inte tillhandahlls av Garmin. Garmin frbehller sig dessutom rtten att avsl garantiansprk avseende produkter eller tjnster som anskaffats och/eller anvnts p ngot stt som strider mot ngot lands lagar. Garmin navigeringsprodukter r endast avsedda att anvndas som hjlp vid resa och fr inte anvndas till ngot ndaml som krver exakt mtning av riktning, strcka, plats eller topografi. Garmin lmnar inga garantier angende kartuppgifternas riktighet eller fullstndighet. Denna begrnsade garanti gller dessutom inte fr, och Garmin r inte ansvarig fr, ngon frsmring av prestanda hos ngon Garmin navigationsprodukt till fljd av dess anvndning i nrheten av mobiltelefon eller annan anordning som utnyttjar markbundet bredbandsntverk som arbetar p eller nra de frekvenser som anvnds av Global Navigation Satellite System

(GNSS), t.ex. Global Positioning Service (GPS). Anvndning av sdana enheter kan frsmra mottagningen av GNSS-signaler. S LNGT SOM R TILLTET ENLIGT GLLANDE LAG GLLER DE GARANTIER OCH KOMPENSATIONER SOM ANGES I DENNA BEGRNSADE GARANTI MED ENSAMRTT OCH I STLLET FR, OCH GARMIN FRISKRIVER SIG UTTRYCKLIGEN FRN, ALLA ANDRA GARANTIER OCH KOMPENSATIONER, VARE SIG UTTRYCKLIGA, UNDERFRSTDDA, LAGSTADGADE ELLER P ANNAT STT, INKLUSIVE, UTAN BEGRNSNING, UNDERFRSTDDA GARANTIER OM SLJBARHET ELLER LMPLIGHET FR ETT VISST NDAML, LAGSTIFTAD KOMPENSATION ELLER P ANNAT STT. DENNA BEGRNSADE GARANTI GER DIG SPECIFIKA LAGLIGA RTTIGHETER, OCH DU KAN HA ANDRA LAGSTADGADE RTTIGHETER SOM KAN VARIERA FRN STAT TILL STAT OCH FRN LAND TILL LAND. OM FRISKRIVNING FRN UNDERFRSTDDA GARANTIER INTE TILLTS ENLIGT LAGSTIFTNING I DITT OMRDE ELLER LAND, R VARAKTIGHETEN AV SDANA GARANTIER BEGRNSADE GENOM DENNA BEGRNSADE GARANTI. VISSA STATER (OCH LAND OCH REGIONER) TILLTER INTE BEGRNSNINGAR AV VARAKTIGHETEN AV EN UNDERFRSTDD GARANTI, S OVANSTENDE BEGRNSNINGAR KANSKE INTE GLLER DIG. GARMIN SKA UNDER INGA OMSTNDIGHETER VID VERTRDELSE AV GARANTIN HLLAS ANSVARIGT FR NGRA TILLFLLIGA, SRSKILDA, INDIREKTA SKADOR ELLER FLJDSKADOR, VARE SIG DE ORSAKAS AV ANVNDNING, MISSBRUK ELLER OFRMGA ATT ANVNDA PRODUKTEN ELLER AV DEFEKTER I PRODUKTEN. VISSA STATER (OCH LAND OCH REGIONER) TILLTER INTE BEGRNSNING AV TILLFLLIGA SKADOR ELLER FLJDSKADOR, S OVANSTENDE BEGRNSNINGAR GLLER KANSKE INTE DIG. Om du under garantiperioden gr ansprk p garantiservice i enlighet med den hr begrnsade garantin, kommer Garmin, efter eget val: (i) reparera enheten med nya delar eller tidigare anvnda delar som uppfyller Garmins kvalitetsstandarder, (ii) erstta enheten med en ny enhet eller rekonditionerad enhet som uppfyller Garmins kvalitetsstandarder, eller (iii) byta enhet fr en fullstndig terbetalning av inkpspriset. DENNA KOMPENSATION R DIN ENDA KOMPENSATION FR EN VERTRDELSE AV GARANTIN. Reparerade eller utbytta enheter har 90 dagars garanti. Om enheten fortfarande omfattas av den ursprungliga garantin gller den nya garantin i 90 dagar eller till slutet av den ursprungliga ettrsgarantin, beroende p vad som intrffar frst. Innan du sker garantiservice kan du beska och granska onlinehjlpsresurserna som finns p support.garmin.com. Om enheten fortfarande inte fungerar korrekt efter anvndning av dessa resurser, kontaktar du en Garmin auktoriserad serviceverkstad i det ursprungliga inkpslandet eller fljer instruktionerna p support.garmin.com fr att erhlla garantiservice. Om du r i USA kan du ocks ringa 1-800-800-1020. Om du efterfrgar garantiservice utanfr det ursprungliga inkpslandet, kan Garmin inte garantera att alla komponenter och produkter som behvs fr att reparera eller erstta produkten finns tillgngliga p grund av skillnader i produktutbud och gllande standarder, lagar och frordningar. I s fall kan Garmin, efter eget gottfinnande och enligt gllande lagar, reparera eller erstta produkten med jmfrbara Garmin produkter och delar eller krva att du skickar produkten till ett Garmin auktoriserat servicecenter i inkpslandet eller till ett Garmin auktoriserat servicecenter i ett annat land som kan utfra service p produkten, i vilket fall du ansvarar sjlv fr att flja alla tillmpliga import- och exportrestriktioner och fr att betala alla tullar, moms, fraktkostnader och andra associerade skatter och avgifter. I vissa fall kan Garmin och dess terfrsljare kanske inte serva produkten i ett land utanfr det ursprungliga inkpslandet eller returnera en reparerad eller utbytt produkt till dig i det landet p grund av gllande standarder, lagar eller frordningar i landet. Inkp via online-auktion: Produkter som kps via online-auktioner berttigar inte till rabatter eller andra specialerbjudanden som grundar sig p Garmin garantin. Bekrftelser p onlineauktion godknns inte som garantiverifikation. Om du vill ha garantiservice mste du ha det ursprungliga inkpskvittot, eller en kopia av den, frn ursprungsterfrsljaren. Garmin erstter inte komponenter som saknas frn en frpackning som kpts via en online-auktion. Internationella inkp: En separat garanti kan tillhandahllas av internationella distributrer fr enheter som inkpts utanfr USA beroende p land. Om tillmpligt tillhandahlls denna garanti av den lokala, inhemska distributren och denna distributr tillhandahller service lokalt fr din enhet. Distributrsgarantier r endast giltiga i det avsedda distributionsomrdet. Garantipolicy fr marina produkter: En del av de marina produkterna frn Garmin inom vissa omrden har en lngre garantiperiod och extra villkor. G till www.garmin.com/support/warranty _marine fr att lsa mer och fr att se om din produkt omfattas av garantipolicyn fr marina produkter frn Garmin. WANE INFORMACJE DOTYCZCE BEZPIECZESTWA I PRODUKTU OSTRZEENIE Zignorowanie poniszych ostrzee moe prowadzi do wypadkw lub kolizji skutkujcych mierci lub powanymi obraeniami ciaa. Ostrzeenia dotyczce obsugi urzdzenia na wodzie Uytkownik jest odpowiedzialny za bezpieczne i roztropne sterowanie swoim statkiem. Niniejsze urzdzenie jest narzdziem wspomagajcym sterowanie statkiem. Nie zwalnia ono uytkownika z obowizku bezpiecznego sterowania swoim statkiem. Naley unika zagroe nawigacyjnych i nigdy nie zostawia steru bez nadzoru. Urzdzenie naley traktowa tylko jako pomoc nawigacyjn. Nie naley korzysta z urzdzenia do celw wymagajcych dokadnych pomiarw kierunku, odlegoci, lokalizacji lub celw topograficznych. Naley zawsze by przygotowanym do szybkiego przejcia sterowania statkiem. Naley zachowa ostrono w pobliu niebezpiecznych wd, to jest w pobliu dokw, palisad oraz innych statkw. Jeli urzdzenia ma funkcj nawigowania, to podczas nawigacji naley dokadnie porwnywa informacje widoczne na wywietlaczu ze wszystkimi dostpnymi rdami nawigacji, w tym z oznaczeniami, mapami oraz lokalnymi przepisami i ograniczeniami obowizujcymi na szlaku wodnym. Ze wzgldw bezpieczestwa przed kontynuowaniem jazdy z uyciem systemu nawigacji naley rozstrzygn wszelkie wtpliwoci. Jeli urzdzenie korzysta z map, dostpne w nim mapy elektroniczne naley traktowa jedynie jako uatwienie, nie za zamiennik dla zatwierdzonych map pastwowych. Oficjalne mapy pastwowe i wskazwki dla marynarzy zawieraj wszystkie informacje niezbdne dla bezpiecznej nawigacji. Jeli urzdzenie zapewnia dane o gbokoci, to nie naley uywa go jako gwnego rda zapobiegajcego osadzeniu na mielinie i kolizji. Odczyty gbokoci naley uzupeni informacjami ze stosownych map papierowych oraz wskanikw optycznych. W przypadku podejrzenia poruszania si po pycinie naley zawsze prowadzi statek z ma prdkoci. Nieprzestrzeganie tego ostrzeenia moe doprowadzi do uszkodzenia statku, a nawet obrae ciaa. Jeli urzdzenie obsuguje sygna wideo, nie wolno oglda ani obsugiwa rde wideo podczas obsugi lub sterowania odzi. Ogldanie lub obsuga obrazu w czasie, gdy statek jest w ruchu moe spowodowa wypadek lub kolizj, a w rezultacie take szkody materialne, powane urazy ciaa lub mier. Ostrzeenie o ryzyku uszkodzenia suchu Ustawianie wysokiego poziomu gonoci w zestawie stereo moe uszkodzi such. NOTYFIKACJA Zignorowanie poniszego ostrzeenia moe prowadzi do uszkodzenia mienia lub obrae ciaa, a take moe negatywnie wpyn na dziaanie urzdzenia. Uwaga dotyczca baterii Zuyte urzdzenie/bateri nienadajc si do dalszego uytku naley przekaza do punktu utylizacji i powtrnego przetwarzania odpadw zgodnie z prawem i przepisami obowizujcymi na danym obszarze. Uwaga dotyczca systemu GPS Moe doj do pogorszenia wydajnoci pracy urzdzenia nawigacyjnego, jeli w jego pobliu znajduj si jakiekolwiek urzdzenia korzystajce z naziemnej sieci szerokopasmowej o czstotliwociach zblionych do czstotliwoci systemu GNSS (globalnego systemu nawigacji satelitarnej), jak na przykad usugi GPS. Korzystanie z takich urzdze moe niekorzystnie wpywa na odbir sygnaw GNSS. Programy ochrony rodowiska dotyczce produktu Informacje na temat programu recyklingu produktu firmy Garmin oraz dyrektyw WEEE, RoHS i REACH, a take innych programw mona znale na stronie www.garmin.com/aboutGarmin

/environment. Deklaracja zgodnoci Firma Garmin niniejszym owiadcza, e produkt ten spenia wymagania dyrektywy 2014/53/UE. Peny tekst deklaracji zgodnoci z przepisami unijnymi mona znale na stronie:

www.garmin.com/compliance. Dane kartograficzne Firma Garmin wykorzystujemy rne rzdowe i prywatne rda danych. Praktycznie wszystkie rda danych zawieraj pewne niedokadne lub niepene informacje. W niektrych krajach pene i dokadne dane kartograficzne nie s dostpne lub ich cena jest zbyt wysoka. Ograniczona gwarancja Niniejsza gwarancja Garmin jest gwarancj producenta, ktra przenosi na konsumenta prawa niezalene od praw wynikajcych z praw ochrony konsumenta (rkojmia), przy czym niniejszy dokument tych ostatnich nie ogranicza ani nie wyklucza. Niniejsza gwarancja pozostaje w mocy przez okres dwch (2) lat od daty zakupu produktu Garmin w Polsce. Prawa ochrony konsumenta: W razie wykrycia wady produktu Garmin, konsument moe skorzysta z praw wynikajcych z nastpujcych przepisw:

Ustawa z 23 kwietnia 1964 kodeks cywilny (tekst jednolity Dz.U. poz. 121 z pniejszymi zmianami) Konsumentowi przysuguje prawo wyboru wnoszenia roszcze z tytuu Ograniczonej Gwarancji Garmin lub praw ochrony konsumenta. Zakres Gwarancji:

Niniejsza gwarancja stanowi, e zakupiony produkt Garmin bdzie wolny od wszelkich wad produkcyjnych i materiaowych przez okres dwch lat od daty zakupu. W tym okresie Garmin moe wedle wasnego uznania naprawi lub wymieni wszelkie komponenty, ktre zepsuj si w warunkach normalnego uytkowania. Rzeczone naprawy lub wymiany zostan dokonane bez obciania klienta kosztami czci, robocizny i transportu. Niniejsza gwarancja nie ma zastosowania do: (i) uszkodze kosmetycznych, np. zadrapa, ubytkw i wgniece; (ii) elementw eksploatacyjnych, np. baterii, o ile uszkodzenie produktu nie wynika z wady materiaowej lub produkcyjnej; (iii) uszkodze spowodowanych wypadkami, naduyciem, niewaciwym uytkowaniem, powodzi, poarem lub innymi zdarzeniami siy wyszej lub czynnikami zewntrznymi; (iv) uszkodze spowodowanych wykonaniem usug przez osoby niebdce autoryzowanymi usugodawcami Garmin; (v) uszkodze produktu, ktry zosta poddany modyfikacjom lub przerbkom bez pisemnej zgody Garmin; lub (vi) uszkodze produktu, ktry zosta podczony do rda zasilania i/lub przewodw do transmisji danych, ktre nie zostay dostarczone przez Garmin. Ponadto Garmin zastrzega sobie prawo do odmowy uznania gwarancji w odniesieniu do produktw lub usug uzyskanych i/lub wykorzystanych z naruszeniem polskiego prawa. Nasze produkty nawigacyjne stanowi wycznie pomoc w planowaniu podry i nie naley ich wykorzystywa do adnych celw wymagajcych precyzyjnego pomiaru kierunku, odlegoci, pooenia ani topografii. Garmin nie udziela adnej gwarancji w zakresie dokadnoci ani kompletnoci danych zwizanych z wgranymi w niniejszym produkcie mapami. Aby skorzysta z obsugi gwarancyjnej naley skontaktowa si z lokalnym autoryzowanym dealerem Garmin lub zadzwoni do Dziau Wsparcia Technicznego Garmin w celu uzyskania wytycznych co do wysyki oraz otrzymania numeru reklamacji - RMA. W Polsce usugi Wsparcia Produktu zapewnia Garmin Polska, Adgar Park West I, Al. Jerozolimskie 181, 02-222 Warszawa Polska telefon: 00 800 441 24 54, mail:

poland.support@garmin.com Garmin moe wedle wasnej decyzji naprawi lub wymieni (na nowy lub nowo naprawiony produkt zastpczy) urzdzenie lub oprogramowanie lub zaproponowa klientowi zwrot penej ceny zakupu w cigu 14 dni od daty otrzymania wadliwego urzdzenia. Jeeli w ramach realizacji swoich zobowiza Garmin dostarczy klientowi wolne od wad urzdzenie, wymieni wadliwe urzdzenie lub przeprowadzi znaczce naprawy urzdzenia w ramach gwarancji, bieg okresu gwarancji rozpocznie si na nowo od momentu dostarczenia pozbawionego wad urzdzenia lub zwrotu naprawionego urzdzenia do koca oryginalnego okresu gwarancji. W innych przypadkach okres gwarancji zostanie przeduony o czas, w ktrym uytkowanie urzdzenia byo niemoliwe wskutek wady urzdzenia objtej gwarancj. Ograniczenie odpowiedzialnoci wobec osb trzecich i uytkownikw komercyjnych:

Garmin w adnym przypadku nie ponosi odpowiedzialnoci za adne straty, ktre nie zostay spowodowane przez naruszenie niniejszej gwarancji przez Garmin, ani za adne szkody uboczne, specjalne, porednie ani wynikowe, w tym za utrat danych, utrat zyskw lub utrat sposobnoci, niezalenie od tego, czy wynikaj one z uycia, niewaciwego uytkowania lub niemonoci uycia niniejszego produktu czy z wad produktu. Niniejsze ograniczenie nie ma zastosowania do (i) zgonu lub szkd cielesnych; (ii) oszustwa; (iii) wiadomego wprowadzenia w bd; lub (iv) innych rodzajw odpowiedzialnoci, ktrych z mocy prawa nie mona ograniczy ani wykluczy. Garmin nie gwarantuje, nie owiadcza i nie zapewnia, e bdzie w stanie naprawi lub wymieni kady produkt Garmin na mocy niniejszej gwarancji bez ryzyka zwizanego z informacjami i/lub danymi przechowywanymi na urzdzeniu Garmin i/lub ich utraty. Prywatno: Wszelkie informacje dotyczce klienta otrzymane w procesie gwarancyjnym bd przechowywane przez Garmin zgodnie z Polityk Prywatnoci Garmin, z ktr mona si zapozna pod adresem www.garmin.com/pl-PL/legal/privacy-statement Istotne ograniczenia usug: Garmin moe ograniczy wiadczenie usug do terytorium EOG i Szwajcarii. Usugi serwisowe w odniesieniu do produktw Garmin moe wiadczy wycznie Garmin lub autoryzowane Centra Serwisowe Garmin Zakupy na aukcjach internetowych: Produkty zakupione na aukcjach internetowych nie podlegaj ochronie gwarancyjnej Garmin. Potwierdzenia zakupu w ramach aukcji internetowych nie bd przyjmowane w celu weryfikacji gwarancji. W wikszoci przypadkw w celu skorzystania z usug gwarancyjnych niezbdny jest dowd zakupu od pierwotnego sprzedawcy. Polityka gwarancji na produkty Garmin Marine: Niektre produkty Garmin Marine w niektrych regionach podlegaj duszemu okresowi gwarancji oraz dodatkowym warunkom. Wicej informacji na ten temat, a take informacj, czy dany produkt obejmuje Polityka Gwarancji na produkty Garmin Marine, mona znale pod adresem www.garmin.com/support/

warranty.html. Oglne: Jeeli jakikolwiek zapis niniejszej gwarancji uznany zostanie za niezgodny z prawem lub niewykonalny, zostanie wyczony z niniejszej gwarancji, co pozostaje bez wpywu dla zgodnoci z prawem i wykonalnoci pozostaych warunkw gwarancji. DLEIT BEZPENOSTN INFORMACE A INFORMACE O PRODUKTU VAROVN Pokud nebudete vnovat pozornost nsledujcm varovnm, mete se vystavit nebezpe nehody nebo kolize, kter me vst ke smrti nebo vnmu zrann. Varovn tkajc se nmonho provozu Za bezpen a rozumn provoz svho plavidla jste odpovdni vy. Toto zazen je nstroj, kter zlep vae monosti ovldn plavidla. Nezbav vs vak odpovdnosti za bezpen provoz plavidla. Vyhnte se naviganm rizikm a nikdy nenechvejte kormidlo bez dozoru. Toto zazen pouvejte pouze jako navigan pomcku. Nepouvejte toto zazen pro ely vyadujc pesn men smru, vzdlenosti, polohy nebo mstopisu. Bute vdy pipraveni urychlen pevzt zen plavidla. Dvejte pozor v blzkosti nebezpench mst ve vod, jako jsou napklad doky, pile a jin plavidla. Pokud m zazen navigan funkce, peliv pi navigaci porovnvejte informace zobrazovan na zazen se vemi ostatnmi zdroji navigace, vetn informac zrakovch vjem, mstnch pravidel a omezen vodnch cest a map. Z bezpenostnch dvod si vyjasnte veker nesrovnalosti dve, ne budete pokraovat v jzd. Obsahuje-li zazen mapy, pouvejte elektronickou mapu v zazen pouze pro usnadnn, nikoli jako nhradu za pouvn ovench sttnch map. Oficiln sttn mapy a poznmky pro nmonky obsahuj vechny potebn informace pro bezpenou navigaci. Nabz-li zazen daje o hloubce, nemly by bt pouvny jako hlavn prostedek zabraujc kotven nebo nrazu. Doplujte daje hodnot o hloubce o informace z pslunch paprovch map a o zrakov vjemy. Pokud mte podezen na mlinu nebo potopen objekty, ovldejte vdy plavidlo za pomal rychlosti. Nevnovn pozornosti tomuto varovn me vst k pokozen plavidla nebo zrann osob. Pokud m zazen funkce vstupu videa, nepokouejte se ovldat nebo sledovat vstup videa pi ovldn nebo navigaci svho plavidla. Ovldn nebo sledovn vstupu videa bhem pohybu plavidla me zpsobit nehodu nebo srku vedouc k pokozen majetku, vnmu zrann nebo smrti. Varovn tkajc se pokozen sluchu Poslech sterea pi vysok hlasitosti me zpsobit pokozen sluchu. OZNMEN Pokud nebudete vnovat pozornost nsledujcm oznmenm, vystavujete se riziku zrann i pokozen majetku nebo negativnho dopadu na funkci zazen. Oznmen o baterich Informace o likvidaci zazen/bateri v souladu s platnmi mstnmi zkony a nazenmi zskte u mstnho stediska pro likvidaci odpad. Oznmen GPS Navigan zazen me vykazovat snen vkon v blzkosti zazen vyuvajcch pozemn irokopsmovou s na podobnch kmitotech jako globln satelitn navigan systmy GNSS

(Global Navigation Satellite System), nap. systm GPS (Global Positioning Service). Pouit tchto zazen me naruit pjem signl GNSS. Produktov ekologick programy Informace o programu recyklace produkt Garmin a o programech WEEE, RoHS, REACH a dalch vyhovujcch programech naleznete na adrese www.garmin.com/aboutGarmin

/environment. Prohlen o shod Spolenost Garmin tmto prohlauje, e produkt odpovd poadavkm smrnice 2014/53/EU. pln znn prohlen o shod pro EU je k dispozici na nsledujc internetov adrese:

www.garmin.com/compliance. Informace o mapovch datech Spolenost Garmin vyuv kombinaci sttnch a soukromch zdroj dat. Tm vechny zdroje dat obsahuj urit nepesn nebo nepln data. Kompletn a pesn mapov data nejsou v nkterch zemch vbec k dispozici nebo jsou nepimen nkladn. Omezen zruka TATO ZRUKA VM POSKYTUJE SPECIFICK ZKONN PRVA. METE MT I JIN ZKONN PRVA, KTER SE MOHOU V RZNCH STTECH LIIT (NEBO ZEMCH I PROVINCICH). SPOLENOST GARMIN NEVYLUUJE, NEOMEZUJE ANI NEPERUUJE PLATNOST JINCH ZKONNCH PRV, KTER METE MT NA ZKLAD ZKON VE VAEM STT (NEBO ZEMI I PROVINCII). K PLNMU POROZUMN SVM PRVM SI PROSTUDUJTE ZKONY VAEHO STTU, ZEM NEBO PROVINCIE. Na neleteck produkty je poskytovna zruka, e budou bez vad materilu a zpracovn po dobu jednoho roku od data zakoupen. Spolenost Garmin si vyhrazuje vhradn prvo opravit nebo vymnit jakoukoli soust, kter pi bnm pouvn sele. Nklady za prci a opravy a vmnu dl nebudou tovny zkaznkovi s vhradou, e zkaznk bude zodpovdn za jakkoli pepravn nklady. Tato omezen zruka se nevztahuje na: (i) kosmetick vady jako pokrbn, oden a promknut; (ii) spotebn sousti, jako baterie, pokud nedolo k pokozen v dsledku vady materilu nebo zpracovn; (iii) pokozen zpsoben nehodou, nedbalost, nesprvnm pouvnm, vodou, zplavou, ohnm nebo jinmi prodnmi ivly a vnjmi vlivy; (iv) pokozen zpsoben provozovnm slueb poskytovatelem neautorizovanm spolenost Garmin; (v) pokozen produktu, kter byl upraven nebo zmnn bez psemnho 11 svolen spolenosti Garmin, nebo (vi) pokozen produktu, kter byl pipojen ke zdroji napjen a/

nebo k datovm kabelm, kter nejsou dodvny spolenost Garmin. Spolenost Garmin si navc vyhrazuje prvo odmtnout reklaman nroky na produkty nebo sluby, kter byly zskny nebo jsou pouvny v rozporu se zkony jakkoli zem.Navigan produkty spolenosti Garmin slou jako cestovn pomcka a nesm se pouvat k jakmkoli elm vyadujcm pesn men smru, vzdlenosti, pozice nebo mstopisu.Spolenost Garmin neposkytuje zruku na pesnost nebo plnost mapovch dat. Tato omezen zruka se nevztahuje na a spolenost Garmin nen zodpovdn za jakkoli snen vkonu naviganho zazen Garmin zpsoben jeho pouitm v blzkosti telefon nebo jinch zazen vyuvajcch pozemn irokopsmovou s na podobnch kmitotech jako globln satelitn navigan systmy GNSS (Global Navigation Satellite System), nap. systm GPS (Global Positioning Service). Pouit tchto zazen me naruit pjem signl GNSS. V MAXIMLNM ROZSAHU POVOLENM PSLUNMI ZKONY, ZRUKY A NHRADY UVEDEN V TTO OMEZEN ZRUCE JSOU VHRADN A NAHRAZUJ VECHNY OSTATN ZRUKY A NHRADY. SPOLENOST GARMIN SE VSLOVN ZK VECH OSTATNCH ZRUK A NHRAD, A JI VYJDENCH, PEDPOKLDANCH, ZKONNCH NEBO JAKCHKOLI JINCH ZEJMNA VECH PEDPOKLDANCH ZRUK OBCHODOVATELNOSTI I VHODNOSTI PRO URIT EL, ZKONNCH NHRAD A PODOBN. TATO ZRUKA VM POSKYTUJE SPECIFICK ZKONN PRVA. METE MT I JIN ZKONN PRVA, KTER SE MOHOU V RZNCH STTECH A ZEMCH LIIT. POKUD NEN MON ZEKNOUT SE PEDPOKLDANCH ZRUK NA ZKLAD ZKON VE VAEM STT (NEBO ZEMI I PROVINCII), JE DOBA TRVN TCHTO ZRUK OMEZENA NA DOBU TRVN TTO OMEZEN ZRUKY. V NKTERCH STTECH (NEBO ZEMCH I PROVINCICH) NEN POVOLENO OMEZEN DOBY PEDPOKLDANCH ZRUK, V TAKOVM PPAD SE VS VE UVEDEN OMEZEN NETK. POKUD JDE O NROKY UINN V SOUVISLOSTI S PORUENM ZRUKY, SPOLENOST GARMIN NEN V DNM PPAD ODPOVDN ZA JAKKOLI NHODN, ZVLTN, NEPM NEBO NSLEDN KODY ZPSOBEN POUVNM, NESPRVNM POUVNM NEBO NEMONOST POUT TENTO VROBEK NEBO KODY ZPSOBEN VADOU VROBKU. V NKTERCH STTECH (A ZEMCH NEBO PROVINCICH) NEN POVOLENO VYLOUEN ODPOVDNOSTI ZA NHODN NEBO NSLEDN KODY, V TAKOVM PPAD SE VS VE UVEDEN OMEZEN ODPOVDNOSTI NETK. Pokud v zrun lht vznesete poadavek na zrun opravu v souladu s touto omezenou zrukou, spolenost Garmin dle vlastnho uven: (i) oprav zazen s pouitm novch nebo dve pouitch dl splujcch standardy kvality spolenosti Garmin, (ii) vymn zazen za nov nebo opraven zazen splujc standardy kvality spolenosti Garmin, nebo (iii) nabdne plnou nhradu nkupn ceny. TENTO NROK BUDE VAM JEDINM A VLUNM NROKEM PI JAKMKOLI PORUEN ZRUKY. Na opraven nebo vymnn zazen je poskytovna 90denn zruka. Pokud odeslan jednotka stle podlh pvodn zruce, pot bude nov zruka 90 dn nebo bude pokraovat do konce pvodn jednolet zruky, podle toho, kter doba bude del. Ne podte o zrun opravu, vyhledejte prosm nejprve pomoc v na online npovd na webov strnce support.garmin.com. Jestlie vae zazen po vyuit tchto zdroj stle nefunguje sprvn, kontaktujte autorizovan servis spolenosti Garmin v zemi, ve kter jste vrobek zakoupili, a podejte o zrun opravu podle pokyn na webov strnce support.garmin.com. Pokud se nachzte v USA, mete tak zavolat na telefonn slo 1-800-800-1020. Pokud chcete podat o zrun opravu v jin zemi, ne je zem, ve kter jste vrobek zakoupili, spolenost Garmin neme zaruit dostupnost dl a produkt potebnch k oprav nebo vmn vaeho vrobku z dvodu odlinosti produktovch nabdek a pslunch norem, zkon a pedpis. V takovm ppad spolenost Garmin me podle svho uven a platnch zkon, opravit nebo vymnit v vrobek za porovnateln vrobek nebo dl Garmin nebo vs podat o odesln vaeho vrobku do autorizovanho servisu spolenosti Garmin v zemi, ve kter jste vrobek zakoupili, nebo do autorizovanho servisu spolenosti Garmin v jin zemi, ve kter lze provst opravu vaeho vrobku, piem nesete odpovdnost za dodrovn platnch zkon tkajcch se importu a exportu, hrady celnch poplatk, DPH, pepravy a ostatnch souvisejcch dan a poplatk. Z dvodu platnch norem, zkon a pedpis v dan zemi spolenost Garmin a jej prodejci nemus bt v nkterch ppadech schopni poskytnout servis, vmnu nebo opravu vrobku v jin zemi, ne je zem, ve kter byl vrobek zakoupen. Zakoupen v online aukci: U produkt zakoupench prostednictvm online aukc nevznik podle zruky spolenosti Garmin nrok na slevu nebo jinou speciln nabdku. Potvrzen z online aukce nejsou k oven zruky pijmny. Chcete-li uznat zrun opravu, je nutn originl nebo kopie pvodn tenky od pvodnho prodejce produkt.Spolenost Garmin neposkytne nhradu za chybjc sousti z jakhokoli balen zakoupenho prostednictvm online aukce. Zakoupen v jinm stt: Na zazen zakoupen mimo zem USA me bt poskytnuta samostatn zruka mezinrodnmi distributory v zvislosti na zemi zakoupen. Pokud je to mon, je tato zruka poskytovna mstnm vnitrosttnm distributorem a tento distributor tak zajiuje mstn servis zazen. Zruky distributora jsou platn pouze na zem pedpokldan distribuce. Politika zruky nmonch produkt: Urit nmon produkty spolenosti Garmin maj v uritch oblastech del zrun lhtu a dodaten podmnky. Dal podrobnosti a informace, zda se na v produkt vztahuje politika zruky nmonch produkt spolenosti Garmin, naleznete na webov strnce www.garmin.com/support/warranty_marine.

, , . 12

. GPS

(GNSS),

(GPS),

. GNSS. Garmin WEEE, RoHS, REACH . - www.garmin.com/aboutGarmin

/environment. Garmin , 2014/53/EC.

: www.garmin.com/compliance. Garmin , ,

( ). GARMIN ,

. Garmin

: (i) ,

, ; (ii) , ,

; (iii) , ,

; (iv) ,

, , Garmin; (v) , Garmin, (vi) ,

/ , Garmin. , Garmin

. Garmin

. Garmin

, Garmin Garmin

(GNSS),

(GPS). GNSS.

, GARMIN

. GARMIN

, Garmin

: (i) ,

, Garmin, (ii)

, Garmin, (iii)

. 90- .

, 90 1- , ,

, : support.garmin.com.

, Garmin support.garmin.com .

, 1-800-800-1020.

, Garmin ,

, . Garmin Garmin Garmin Garmin ,

, . Garmin

, Garmin.

. Garmin

. Garmin

- www.garmin.com/support/warranty_marine,

, Garmin . VANE INFORMACIJE O SIGURNOSTI I PROIZVODU UPOZORENJE Ako se ne pridravate sljedeih upozorenja, moe doi do nesree ili sudara koji mogu rezultirati smrtnim sluajem ili ozbiljnom ozljedom. Upozorenja za koritenje u pomorske svrhe Vi ste odgovorni za sigurno i oprezno upravljanje plovilom. Ovaj je ureaj alat koji poboljava mogunost upravljanja plovilom. Ureaj vas ne oslobaa odgovornosti za sigurno upravljanje plovilom. Izbjegavajte navigacijske opasnosti i nikad ne ostavljajte kormilo bez nadzora. Ureaj koristite iskljuivo kao pomo u navigaciji. Ureaj ne koristite za postupke u kojima je potrebno precizno mjerenje smjera, udaljenosti, lokacije ili topografije. Uvijek budite spremni brzo preuzeti kontrolu nad plovilom. Budite oprezni u blizini opasnosti u vodi poput dokova, stupova i drugih plovila. Ako ureaj ima mogunost navigacije, tijekom navigacije paljivo usporeujte informacije prikazane na ureaju sa svim dostupnim navigacijskim izvorima, ukljuujui vizualne informacije, lokalne pravilnike o vodenim putovima i karte. Iz sigurnosnih razloga uvijek rijeite sva neslaganja ili pitanja prije no to nastavite s navigacijom. Ako ureaj koristi karte, elektroniku kartu ureaja koristite samo kako biste si olakali upotrebu ovlatenih vladinih karata, a ne kao njihovu zamjenu. Slubene vladine karte i obavijesti mornarima sadre sve informacije potrebne za sigurnu navigaciju. Ako ureaj daje podatke o dubini, oni se ne smiju koristiti kao primarni nain sprjeavanja nasukavanja ili sudara. Oitanjima podataka o dubini dodajte podatke s primjenjivih karata i vizualnih pokazatelja. Plovilom uvijek upravljajte pri niskim brzinama ako sumnjate na plitku vodu ili objekte pod vodom. U sluaju nepotivanja ovog upozorenja, moglo bi doi do oteenja ili tjelesnih ozljeda. Ako ureaj ima mogunost primanja ulaznih video podataka, nemojte rukovati njima ili ih gledati dok upravljate ili navigirate plovilom. Rukovanje video podacima ili gledanje video podataka dok je plovilo u pokretu moe dovesti do nesretnog sluaja ili sudara ije posljedice mogu biti teta, ozbiljne ozljede ili smrt. Upozorenja za oteenja sluha Glasno sluanje sterea moe vam otetiti sluh. OBAVIJEST Nepridravanje sljedee obavijesti moe uzrokovati ozljede ili oteenja imovine ili negativno utjecati na rad ureaja. Napomena o bateriji Obratite se lokalnoj jedinici za odlaganje otpada radi odlaganja ureaja/baterija u skladu s vaeim lokalnim zakonima i propisima. Obavijest o GPS-u Koritenje blizu bilo kojeg ureaja koji koristi zemaljsku irokopojasnu mreu na frekvencijama koje su blizu frekvencija koje koristi bilo koji sustav za globalnu navigaciju (GNSS), npr. sustav za globalno pozicioniranje (GPS), moe negativno utjecati na rad navigacijskog ureaja. Koritenje takvih ureaja moe negativno utjecati na prijem GNSS signala. Programi za ouvanje okolia Informacije o programu recikliranja tvrtke Garmin te programima WEEE, RoHS, REACH i drugim programima potraite na adresi www.garmin.com/aboutGarmin/environment. Izjava o usklaenosti Tvrtka Garmin ovime izjavljuje da je ovaj proizvod usklaen s Direktivom 2014/53/EU. Cijeli tekst EU Izjave o usklaenosti dostupan je na sljedeoj internetskoj adresi: www.garmin.com

/compliance. Informacije o podacima karte Tvrtka Garmin koristi kombinaciju dravnih i privatnih izvora podataka. Gotovo svi izvori podataka sadre neke netone ili nepotpune podatke. U nekim dravama potpune i precizne informacije na kartama nisu dostupne ili su vrlo skupe. Ogranieno jamstvo OVO VAM OGRANIENO JAMSTVO DAJE POSEBNA ZAKONSKA PRAVA, A OVISNO OD DRAVE DO DRAVE (ILI POKRAJINE), MODA IMATE I NEKA DRUGA ZAKONSKA PRAVA. GARMIN NE ISKLJUUJE, OGRANIAVA ILI OBUSTAVLJA OSTALA ZAKONSKA PRAVA KOJA MODA IMATE NA TEMELJU ZAKONA VAE DRAVE (ILI POKRAJINE). KAKO BISTE SE U POTPUNOSTI UPOZNALI SA SVOJIM PRAVIMA, PROUITE ZAKONE VAE DRAVE ILI POKRAJINE. Proizvodi koji nisu namijenjeni zrakoplovstvu imaju jamstvo da nee imati pogreaka u materijalu ili izradi do godinu dana od datuma kupnje. Unutar tog razdoblja Garmin e, po vlastitoj odluci, popraviti ili zamijeniti komponente koje nisu ispravno radile prilikom uobiajene upotrebe. Takvi popravci ili zamjene bit e besplatni za korisnika za dijelove ili rad, pod uvjetom da korisnik podmiri trokove transporta. Ovo ogranieno jamstvo ne vrijedi za: (i) kozmetika oteenja kao to su ogrebotine, zarezi i udubljenja; (ii) potrone dijelove poput baterija, osim ako teta nije uzrokovana manjkavim materijalima ili izradom; (iii) tetu uzrokovanu nesretnim sluajem, zlouporabom, nepravilnim koritenjem, vodom, poplavom, poarom ili drugim prirodnim nepogodama ili vanjskim uzrocima; (iv) tetu uzrokovanu servisiranjem od strane osobe koja nije ovlateni serviser tvrtke Garmin; (v) tetu na proizvodima koji su modificirani ili preinaeni bez pisanog doputenja tvrtke Garmin ili (vi) tetu na proizvodima koji su prikljueni na kabele napajanja i/ili podatkovne kabele koje nije isporuila tvrtka Garmin. Isto tako, Garmin zadrava pravo odbijanja jamstvenih zahtjeva za proizvode ili usluge dobivene i/ili koritene u suprotnosti sa zakonima bilo koje drave. Garmin navigacijski proizvodi namijenjeni su iskljuivo za upotrebu kao pomagala u putovanjima i ne smiju se koristiti u svrhu gdje su potrebna precizna mjerenja smjera, udaljenosti, lokacije ili topografije. Garmin ne jami preciznost i potpunost kartografskih podataka. Ovo se ogranieno jamstvo ne odnosi na loiji rad bilo kojeg Garmin navigacijskog ureaja koji je posljedica koritenja ureaja u blizini bilo kojeg runog ili drugog ureaja koji koristi zemaljsku irokopojasnu mreu na frekvencijama koje su blizu frekvencija koje koristi bilo koji sustav za globalnu navigaciju (GNSS), npr. sustav za globalno pozicioniranje (GPS), niti je tvrtka Garmin za njega odgovorna. Koritenje takvih ureaja moe negativno utjecati na prijem GNSS signala. DO MJERE DO KOJE TO DOPUTA PRIMJENJIVI ZAKON, JAMSTVA I PRAVNI LIJEKOVI NAVEDENI U OVOM OGRANIENOM JAMSTVU ISKLJUIVI SU I TVRTKA GARMIN IZRIITO SE ODRIE SVIH DRUGIH JAMSTAVA I PRAVNIH LIJEKOVA, BILO IZRIITIH, IMPLICIRANIH, ZAKONSKIH ILI BILO KAKVIH DRUGIH, UKLJUUJUI BEZ OGRANIENJA BILO KOJE IMPLICIRANO JAMSTVO ZA TRINI POTENCIJAL ILI PRIKLADNOSTI ZA ODREENU NAMJENU, BILO ONO ZAKONSKO ILI PO NEKOJ DRUGOJ OSNOVI. OVO VAM OGRANIENO JAMSTVO DAJE POSEBNA ZAKONSKA PRAVA, A OVISNO OD DRAVE DO DRAVE, MODA IMATE I NEKA DRUGA ZAKONSKA PRAVA. AKO SE IMPLICIRANIH JAMSTAVA NE MOE ODREI NA TEMELJU ZAKONA VAE DRAVE, TRAJANJE TAKVIH JAMSTAVA OGRANIENO JE NA TRAJANJE OVOG OGRANIENOG JAMSTVA. NEKE DRAVE (I POKRAJINE) NE DOPUTAJU OGRANIAVANJE TRAJANJA IMPLICIRANOG JAMSTVA, PA SE GORNJE OGRANIENJE MODA NEE PRIMJENJIVATI NA VAS. U SLUAJU NEPOTOVANJA JAMSTVA TVRTKA GARMIN NI U KOJEM SLUAJU NEE SNOSITI ODGOVORNOST ZA BILO KAKVA SLUAJNA, POSEBNA, NEIZRAVNA ILI POSLJEDINA OTEENJA, BEZ OBZIRA JESU LI REZULTAT UPOTREBE, POGRENE UPOTREBE ILI NEMOGUNOSTI UPOTREBE OVOG PROIZVODA ILI MANJKAVOSTI PROIZVODA. NEKE DRAVE (I POKRAJINE) NE DOPUTAJU ISKLJUIVANJE SLUAJNE ILI POSLJEDINE TETE TE SE GORNJA OGRANIENJA MODA NEE PRIMJENJIVATI NA VAS. Ako tijekom jamstvenog razdoblja podnesete zahtjev za jamstvenim servisom u skladu s ovim Ogranienim jamstvom, Garmin e po vlastitom odabiru: (i) popraviti ureaj pomou novih dijelova ili rabljenih dijelova koji zadovoljavaju standarde kvalitete tvrtke Garmin, (ii) zamijeniti ureaj novim ureajem ili obnovljenim ureajem koji zadovoljava standarde kvalitete tvrtke Garmin ili (iii) zamijeniti ureaj za puni povrat kupovne cijene koju ste platili. TAKAV PRAVNI LIJEK BIT E VA JEDINI I ISKLJUIVI PRAVNI LIJEK U SLUAJU NEPOTOVANJA JAMSTVA. Jamstvo na popravljene ili zamijenjene ureaje iznosi 90 dana. Ako je poslana jedinica jo uvijek pokrivena izvornim jamstvom, onda novo jamstvo traje 90 dana ili do kraja izvornog jednogodinjeg jamstva, to god je due. Prije slanja zahtjeva za jamstveni servis, pristupite resursima za pomo na web-mjestu support.garmin.com i prouite ih. Ako va ureaj i dalje ne radi ispravno i nakon upotrebe tih resursa, obratite se ovlatenom servisu tvrtke Garmin u dravi u kojoj ste kupili ureaj ili slijedite upute na web-mjestu support.garmin.com kako biste ostvarili jamstveni servis. Ako se nalazite u SAD-u, moete nazvati broj telefona 1-800-800-1020. Ako vam je jamstveni servis potreban izvan drave u kojoj ste kupili proizvod, Garmin ne moe jamiti da e dijelovi i proizvodi potrebni za popravak ili zamjenu vaeg proizvoda biti dostupni zbog razliitih ponuda proizvoda i razliitih vaeih standarda, zakona i propisa. U tom sluaju tvrtka Garmin moe po vlastitom nahoenju i u skladu s vaeim zakonima popraviti ili zamijeniti va proizvod usporedivim Garmin proizvodima i dijelovima ili od vas zatraiti da svoj proizvod poaljete u ovlateni servis tvrtke Garmin u dravi u kojoj ste kupili proizvod ili u ovlateni servis tvrtke Garmin u nekoj drugoj dravi u kojoj je va ureaj mogue servisirati, pri emu snosite odgovornost za potivanje svih vaeih zakona i propisa o uvozu i izvozu te za plaanje svih carina, PDV-a, potarina i ostalih vezanih poreza i naknada. U nekim sluajevima tvrtka Garmin i njezini ovlateni zastupnici moda nee moi servisirati va proizvod u dravi izvan drave u kojoj ste kupili proizvod ili vam vratiti popravljeni ili zamijenjeni proizvod u tu dravu zbog vaeih standarda, zakona ili propisa u toj dravi. Kupnja putem online aukcija: Proizvodi kupljeni na online aukcijama ne podlijeu popustima ili drugim posebnim ponudama unutar jamstva tvrtke Garmin. Potvrde online aukcija ne prihvaaju se kao potvrda jamstva. Za dobivanje jamstvene usluge potreban je izvornik ili kopija rauna od ovlatenog dobavljaa. Garmin nee zamijeniti komponente koje nedostaju iz paketa kupljenih putem online aukcije. Meunarodna kupovina: Meunarodni distributeri mogu dati zasebno jamstvo za ureaje koji su kupljeni izvan Sjedinjenih Amerikih Drava, ovisno o dravi. Ako je to primjenjivo, ovo jamstvo daje lokalni distributer koji osigurava i lokalno servisiranje vaeg ureaja. Jamstva distributera valjana su samo u podruju namijenjene distribucije. Jamstvo za pomorske ureaje: Odreeni pomorski ureaji tvrtke Garmin u odreenim podrujima imaju dua jamstvena razdoblja i dodatne uvjete i odredbe. Na stranici www.garmin.com/support/warranty_marine moete pronai dodatne pojedinosti i provjeriti odnosi li se jamstvo za nautike ureaje tvrtke Garmin i na va proizvod. 13

. GPS

(GNSS),

(GPS). GNSS. Garmin WEEE, RoHS, REACH, www.garmin.com/aboutGarmin/environment.

, Garmin 2014/53/. Internet: www.garmin.com/compliance. H Garmin .

( ). GARMIN

, . , Garmin ,

. : (i)

, , , (ii) ,

, (iii) , , , , ,

, (iv) , Garmin, (v) Garmin (vi)

Garmin. , Garmin

. Garmin

, , . Garmin

, Garmin Garmin,

(GNSS), 14

(GPS). GNSS.

, GARMIN

. GARMIN , ,

, Garmin

: (i) Garmin, (ii) Garmin, (iii)

. 90 .

, 90 1 , .

, support.garmin.com.

, Garmin support.garmin.com,

. , 1-800-800-1020.

, Garmin

. , Garmin ,

, Garmin, Garmin Garmin

, Garmin

Garmin. Garmin ,

: Garmin

. www.garmin.com/support/warranty_marine Garmin .

GPS

(GNSS)

(GPS) GNSS Garmin WEEERoHSREACH www.garmin.com/aboutGarmin/environment Garmin 2014/53/EU www.garmin.com/compliance Garmin

/ GARMIN

Garmin

(i)

(ii) (iii)

(iv) Garmin (v) Garmin

(vi) Garmin

/ Garmin Garmin Garmin Garmin Garmin

(GNSS)

(GPS) GNSS GARMIN

GARMIN /

Garmin

(i) Garmin (ii) Garmin (iii) 90 90 1 support.garmin.com Garmin /

support.garmin.com 1-800-800-1020

Garmin Garmin Garmin /

Garmin / Garmin Garmin

Garmin Garmin

Garmin www.garmin.com/support/warranty_marine Garmin 15

 

 

 

 

 

 

 

 

 

 

A03873 Box Artwork FCC/ICES Information Made in Taiwan. Cables made in China or Taiwan. 007-03876-01 Rev. A 170-02399-01 FCC ID: IPH-03873 IC: 1792A-03873 M/N:A03873 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

 

 

B03873 Box Artwork FCC/ICES Information FCC ID: IPH-03873 IC: 1792A-03873 M/N:B03873 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

 

 

Per the allowances in 47 CFR 2.935 this device employs an electronic label. The electronic label on the device is as follow The product's electronic label can be accessed from the home screen by pressing

- Settings

- System

- Regulatory Information Display presented is shown below Pertinent LINHA sS4}

IC: 17924-03873 FCC ID: IPH-03873 De CM CUS eRe keen Comerica ROR uO RLIeR Cc mute ecto interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 04:584 SOT eet san) LED Sie}

IC: 1792A-03873 FCC ID: |PH-03873 ao This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful Ree OR etter eee a eae ced eC CtoCuc UCC mete Us Coiec ne er dcum

(Ont ME}

Rogers Labs, Inc. Garmin International, Inc. West 259" Terrace A03873, B03873 st: 200713_14 Test to: 47 CFR 15C, RSS. File: 03873 LabelSmpl FCC ID: IPH-03873 IC: 1792A-03873 6556773 Date: October 2 Page 1 of 1

 

 

ROGERS LABS, INC. 4405 West 259th Terrace Louisburg, KS 66053 913 837-3214 October 20, 2020 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Applicant:

Garmin International, Inc. 1200 East 151st Street Olathe, KS 66062 Re: Confidentiality for submittal information regarding FCC ID: IPH-03873 Product: Transmitter operated under 47CFR Section 15C Dear Sirs:

Garmin International, Inc. requests that the material in the Block Diagram, Operational Description, Schematics, and Tune up Procedure be withheld from public disclosure pursuant to Sections 0.457 and 0.459 of the Commissions Rules following grant of the application. In support of this request, Garmin International, Inc. submits the following information. CONFIDENTIAL FILES 03873 Conf BlkDia.pdf 03873 Conf OpDes.pdf 03873 Conf Schem.pdf 03873 Conf TunPro.pdf 1. Identification of the specific information for which confidential treatment is sought:

The materials set forth in the Block Diagram, Operational Description, Schematics, and Tune up Procedure which are segregated, from the non-confidential exhibits of the application, are those for which confidentiality is sought. 2. Identification of the Commission proceeding in which the information was submitted or a description of the circumstances giving rise to the submission:

The proceeding is that involving the application for equipment authorization (certification) under FCC ID: IPH-03873 3. Explanation of the degree to which the information is commercial or financial, or contains a trade secret or is privileged:

This material includes a detailed Block Diagram, Operational Description, Schematics, and Tune up Procedure. As such, this material is treated as highly confidential business information. Page 1 of 2 4. Explanation of the degree to which the information concerns a service that is subject to competition:

The material for which confidentiality is sought is employed in the design and manufacture of this transmitting equipment that is offered on a highly competitive basis. Customers for this equipment have a variety of competing sources. 5. Explanation of how disclosure of the information could result in substantial competitive harm:

Disclosure would, in effect, give away the fruits of the labors of Garmin International, Inc.s engineering personnel, who have designed the equipment and the manufacturing process. Disclosure would also offer competitors additional unwarranted insight into the state of the product development, thereby allowing competitors an advantage, not available to Garmin International, Inc. 6. Identification of any measures taken by the submitting party to prevent unauthorized disclosure:

The information for which confidential treatment is sought is kept confidential by Garmin International, Inc. and not made available to third parties except pursuant to non-disclosure agreements. 7. Identification of whether the information is available to the public and the extent of any previous disclosure of the information to third parties:

To the knowledge of those preparing this application, the information has not been disclosed publicly heretofore. While the general theory of operation of this equipment has been the subject of numerous disclosures in industry the protection sought is narrowly drawn as provided in regulations. 8. Justification of the period during which the submitting party asserts that the material should not be available for public disclosure:

This material should not be disclosed for at least 25 years. While improvements in design are made relatively frequently, disclosure of the design information would lead to insights into both design and manufacturing techniques that could have an adverse competitive effect for many years to come. As such, it is important that the design not be made available to unauthorized persons who might attempt to use knowledge of the design to compromise the applications for which the equipment will be employed. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers Page 2 of 2

 

 

suejyy Aloyepnsoy pure jeyouuoll A [a1Q0UIS ulMe Aq AleIVUOS 9Y} 0} PoljOU [UN jOOJJO Ul SUTBWOI UOTJeZIIOYINE STYy], poLiojoid 10 Aressaoou SI uoNR\soye 8, [eNPLAIpUT pozoyNe,, Ue dIIYM J[PYOq S,UIWIBD UO 1d O} , S[ENPIAIPUT poZioyNe,, poloprsuosd oq [[eYS S[eNprAIpUI soy} UOTIppe UT UTWIeD Jo Jyeyoq UO SGD I, pozuoyne Jo/pue Oo]

JOH OY} YIM UOTLULIOJUI pue eyep oduLYyoxa (p pue A}ITeLUDpIZUOD ysonbos ( UoTyeortTdde Jo SIO}JO[ UBIS (Z [ EL WIO USIS ({ :0} poZOYINE oe DAOGK PdjSI] SOWVIOOSSYW UTWIeD oy} Yons sy SJONPOId SSOU}L 2 SSOUT[IA\ II0UISU_ soURTTdWIO| JyeIS NP plaeq II sjonpolg suLeyy Jooursuy souelduio,g wospuns oy II sjonpolg Joopyng 1souIsu_ souel[duo0|g per 1ouLog WRIA I sjonpolg WAO OMY z= sAnoWO ny JouNsuUOD I990UIsU_ soURTTdUIOD IOTUdS UOS|O UN] I SULIDOUISUY OURT[CWIOD Iopeo'] Wes] souor pIpeH IP sjonpolg sAOWO MY JowNsUOD Is0UISU_ soURT]dUIOZ JOTUSS Ys UeC IP sjonpolg suLIey Is0uIsuy souRT[dWOD pes Aorep Adore I SJONPOL SSL] WZ SSOUT[AM I90UTSUA DOURT[dWIOD JoTUNS sysnoNg 3noq I UOTJBOTF IVINS JO UOTeZLIoyNe yUoUIdInbs J0F (AS) epeued Juswidoysaoq] s1wIoU0Nq puke 9dUdTIS UOIJVAOUU] pue (D044) UOISSIWUWIOD UOTBOTUNWWO| [eJopo,J 94} 0} suoneotdde Surssooo01d Jo osodind ssoidxo pure o]0s oY} OF JyeYoq S,UTWIeD UO JOR 0} SoJeIDOSSY [CUOTUIOWU] UTULIeED SUIMOT[OJ OY} pozoyyNe sey (UIWIeD) OUT euONeUIO}UT UIUIeD 116C YAO Lp O} Juensing suI20U0Z) ARP] IT WOYA\ OL, ZS8 HZ epeury ouejO eaeno H woneig O61 XOG Od 9POIZ CIN eIquinjos OnUSAY SUITED [OLE peod sy puepyeo ceri nesing SULIZSUISU_ pUe UONBOIOD ~sUOISTAIC] UOTJeNTeAY pue uoyezuoyNy epeues JuoWdojaaog SWIOUOD puke soUDIDg UONBAOCUU] = UOISSTUIIOD SuOTROTUNUIUIOD [eI9p9,q 6107 I Arne 7828-L6E-E16 4 OOZ8-LEE-E16 d cee | NIWWS 1991S ISLGL 1Se9 OOZL Ju, peuoneusazuy uiwsey

 

 

 

 

 

 

Garmin International, Inc. 1200 East 151st Street GAI <M | N. Olathe, Kansas 66062 P: 913+397-=8200 F: 913-397-8282 May 20, 2016 Federal Communications Commission Equipment Approval Services Post Office Box 358315 Pittsburgh, Pennsylvania 15215-5315 To Whom It May Concern:

Pursuant to 47 CFR 2.911, Garmin International, Inc. (Garmin) has authorized Mr. Scot Rogers of Rogers Labs, Inc. to act on Garmin's behalf for the sole and express purpose of processing applications to the FCC for equipment authorization. As such, Mr. Rogers is authorized to:

1) sign Form 731 2) sign letters of application 3) request confidentiality 4) exchange data and information with the FCC and authorized TCBs on behalf of Garmin. This authorization is not assignable to others beyond Mr. Scot Rogers. This authorization is in effect until notified to the contrary by Garmin. Sincerely, 7 1) J /

Jy vs /

JA | ,,- [ ct i A fv Tuy AN \f yA) yh

Douglas Kealey Manager, Environmental and Regulatory Affairs cc by email: Scot Rogers, Rogers Labs, Inc.