FCC ID: IPH-02546 Marine Radar

GMR A02546 4/6 Installation Instructions Important Safety Information WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. The radar transmits electromagnetic energy. Ensure that the radar is installed according to the recommendations in these instructions and that all personnel are clear of the path of the radar beam before transmitting. When properly installed and operated, the use of this radar conforms to the requirements of ANSI/IEEE C95.1-1992 Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields. When the radar is transmitting, do not look directly at the antenna at close range; eyes are the most sensitive part of the body to electromagnetic energy. When connecting the power cable, do not remove the in-line fuse holder. To prevent the possibility of injury or product damage caused by fire or overheating, the appropriate fuse must be in place as indicated in the product specifications. In addition, connecting the power cable without the appropriate fuse in place voids the product warranty. CAUTION This device should be used only as a navigational aid. Do not attempt to use the device for any purpose requiring precise measurement of direction, distance, location, or topography. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. NOTICE When drilling or cutting, always check what is on the opposite side of the surface. Registering Your Device Help us better support you by completing our online registration today. Go to my.garmin.com. Keep the original sales receipt, or a photocopy, in a safe place. Contacting Garmin Product Support Go to www.garmin.com/support for in-country support information. In the USA, call 913-397-8200 or 1-800-800-1020. In the UK, call 0808 238 0000. In Europe, call +44 (0) 870 850 1241. Tools Needed

#2 Phillips screwdriver 5 mm hex wrench Drill 15.0 mm (19/32 in.) drill bit 32 mm (1 1/4 in.) drill bit (optional) 17 mm (21/32 in.) wrench and torque wrench 3.31 mm (12 AWG) copper wire to ground the radar housing

(the length depends on the distance from the radar to ground) Marine sealant Mounting Considerations When selecting a mounting location, observe these considerations. It is highly recommended that the device is mounted out of range of people, with the vertical beam width above head height. To avoid exposure to harmful radio frequency (RF) levels, the device should not be mounted closer to people than the maximum safe distance value listed in the product specifications. The device should be mounted high above the ships keel line with minimal blockage of the radar beam. Obstructions may cause blind and shadow sectors, or generate false echoes. The higher the installation position, the farther the radar can detect targets. The device should be mounted on a flat surface or a platform that is parallel to the vessel's water line and is sturdy enough to support the device's weight. The weight for each model is listed in the product specifications. The radar beam spreads vertically 11.5 above and 11.5 below the radar's radiating element. On vessels with higher bow angles at cruise speed, the installation angle can be lowered to point the beam slightly downward to the waterline while at rest. Shims can be used if necessary. The device should be mounted away from heat sources, such as smoke stacks and lights. The device should be mounted at a different level than horizontal spreaders and mast crosstrees. To avoid interference with a magnetic compass, the device should not be mounted closer to a compass than the compass-safe distance value listed in the product specifications. Other electronics and cables should be mounted more than 2 m (6.5 ft.) from the radar beam path. GPS antennas should be either above or below the radar beam path. The device should be mounted at least 1 m (40 in.) from any transmitting equipment. The device should be mounted at least 1 m (40 in.) away from cables carrying radio signals such as VHF radios, cables, and antennas. The device should be mounted at least 2 m (6.5 ft.) away from Single Side Band (SSB) radios. February 2016 Printed in Taiwan 190-01967-91_01 Installation Procedures Preparing the Radar Mounting Surface Before you can mount the radar, you must choose a suitable mounting location (Mounting Considerations, page 1). 1 Secure the included mounting template to the surface at the mounting location, along the bow-stern axis, as indicated on the template. 2 Drill the mounting holes using a 15 mm (19/32 in.) drill bit. 3 If you need to run the power and network cables through the mounting surface, select a location along the center channel indicated on the template, drill a pass-through hole for the cables using a 25 mm (1 in.) drill bit, and route the cables through the surface (optional) (Cable Considerations, page 2). 4 Remove the mounting template from the surface. Mounting the Radar Before you can mount the radar, you must select a mounting location (Mounting Considerations, page 1) and prepare the mounting surface (Preparing the Radar Mounting Surface, page 2). 1 From under the mounting surface, place the included plastic shoulder washers into the holes you drilled when preparing the mounting surface. 2 Place the radar onto the mounting surface, aligning the holes on the base of the radar with the holes in the shoulder washers. 3 Insert the threaded rods through the mounting surface and into the radar base, and tighten them using a 5 mm hex wrench. To avoid damaging the pedestal, you should stop tightening the threaded rods when they no longer turn easily. 4 Place the flat washers , lock washers , and hex nuts on the threaded rods. 5 Tighten the hex nuts to a torque of 14.7 N-m (11 lbf-ft.) to securely fasten the radar to the surface without damaging the radar or the mounting hardware. Installing the Antenna Before you can install the antenna on the radar, you must securely mount the pedestal (Mounting the Radar, page 2). 1 Remove the protective cover from the waveguide on the top of the pedestal . 2 2 Align the waveguide on the pedestal with the socket on the bottom of the antenna , and slide the antenna onto the pedestal. 3 Secure the antenna to the pedestal by tightening the captive hex bolts under the antenna arm. 4 Tighten the hex bolts to a torque of 7.9 N-m (6 lbf-ft.) to fasten the antenna to the pedestal without damaging the antenna or the mounting hardware. Cable Considerations It may be necessary to drill 25 mm (1 in.) holes for routing the power or network cables. When routing both the power and network cables through the same hole, you must route the network cable before the power cable. You must apply marine sealant to the hole after the cables are in place to ensure a waterproof seal. If the routing hole must be made in a visible location, decorative cable grommets can be purchased from Garmin or a Garmin dealer (optional). You must drill a 31.7 mm (11/4 in.) hole to use the optional grommet. If needed, the grommet can be trimmed to enable you to route both the network and the power cable through the same hole. The optional grommet does NOT provide a waterproof seal. You must apply marine sealant to the grommet after the cables are in place ensure a waterproof seal. When installing the network and power cables, you should observe these considerations. Cutting the Garmin Marine Network cable is not recommended, but a field install kit can be purchased from Garmin or a Garmin dealer if cutting the network cable is necessary. To ensure safety, appropriate tie-wraps, fasteners, and sealant should be used to secure the cable along the route and through any bulkheads or the deck. Cables should not be run near moving objects and high-heat sources or through doorways and bilges. To avoid interference with other equipment, network and power cables should not be run next to or parallel to other cables, such as radio antenna lines or power cables. If this is not possible, the cables should be shielded with metal conduit or a form of EMI shielding. The power cable should be installed as close to the battery source as possible. If it is necessary to extend the power cable, the appropriate gauge of wire must be used (Power Cable Extensions, page 3). Incorrectly extended runs of cable may cause the radar to malfunction due to insufficient power transmission. Connecting to Power WARNING When connecting the power cable, do not remove the in-line fuse holder. To prevent the possibility of injury or product damage caused by fire or overheating, the appropriate fuse must be in place as indicated in the product specifications. In addition, connecting the power cable without the appropriate fuse in place voids the product warranty. Item Description To the Garmin Marine Network 15 A fuse holder To the boat battery (from 10 to 32 Vdc) Water ground connection 1 Route the power cable to the radar and boat battery. 2 Connect the power cable to the boat battery. 3 Connect the power cable to the POWER port on the radar. Power Cable Extensions Connecting the power cable directly to the battery is recommended. If it is necessary to extend the cable, the appropriate gauge of wire must be used for the length of the extension. You must use crimp connectors and heat-shrink to create a water-resistant connection. Distance 3 m (9 ft. 10 in.) 5 m (16 ft. 4 in.) 6.5 m (21 ft. 3 in.) 8 m (26 ft. 2 in.) Wire Gauge 3.31 mm (12 AWG) 5.26 mm (10 AWG) 6.63 mm (9 AWG) 8.36 mm (8 AWG) Grounding the Radar The radar must be connected to the appropriate type of ground using a 3.31 mm (12 AWG) copper wire (not included). 1 Route a 3.31 mm (12 AWG) copper wire to a water ground location and to the radar pedestal. 2 Connect the wire to the ground connector (

pedestal using the pre-installed crimp connector .

) on the 3 Coat the ground screw and crimp connector with marine sealant. 4 Connect the other end of the wire to the water ground location on the boat, and coat the connection with marine sealant. Garmin Marine Network Considerations This device connects to Garmin Marine Network devices to share radar data with compatible devices on the network. When connecting to a Garmin Marine Network device, observe these considerations. A Garmin Marine Network cable must be used for all Garmin Marine Network connections. Third-party CAT5 cable and RJ45 connectors must not be used for Garmin Marine Network connections. Additional Garmin Marine Network cables and connectors are available from your Garmin dealer. Although it is not recommended, you can use a field-

installable connector to create a custom-length Garmin Marine Network cable if necessary. Follow the directions provided with the connector. Radar Operation All functions of this radar are controlled with your Garmin chartplotter. See the Radar section of your chartplotter's manual for operating instructions. To download the latest manual, go to www.garmin.com/support/. Software Update You may need to update the device software when you install the device or add an accessory to the device. The software update requires either a Garmin memory card reader accessory or another Garmin chartplotter connected over the Garmin Marine Network. Loading the New Software on a Memory Card The device may contain a software-update memory card. If so, follow the instructions provided with the card. If a software update memory card is not included, you must copy the software update to a memory card. 1 Insert a memory card into the card slot on the computer. 2 Go to www.garmin.com/support/software/marine.html. 3 Select Download next to Garmin Marine Network with SD card. 4 Read and agree to the terms. 5 Select Download. 6 Select Run. 7 Select the drive associated with the memory card, and select Next > Finish. Updating the Device Software Before you can update the software, you must obtain a software-update memory card or load the latest software onto a memory card. 1 Turn on the chartplotter. 2 After the home screen appears, insert the memory card into the card slot. NOTE: In order for the software update instructions to appear, the device must be fully booted before the card is inserted. 3 Follow the on-screen instructions. 4 Wait several minutes while the software update process completes. 5 When prompted, leave the memory card in place and restart the chartplotter manually. 6 Remove the memory card. NOTE: If the memory card is removed before the device restarts fully, the software update is not complete. Specifying the Antenna Size Before you can use the radar on your system, you must specify the antenna size. 3 You must mount the radar, connect it to power, and connect it to the Garmin Marine Network before you can specify the antenna size. 1 Turn on the radar and all devices connected to the Garmin Marine Network. An antenna-selection prompt appears on the connected chartplotters. NOTE: If the entire system is being turned on for the first time, the antenna-selection screen is part of the initial setup process. 2 Select the installed antenna size for each open-array radar installed on the boat. TIP: If you need to specify a different antenna size, while viewing the radar screen for the radar you want to change , select Menu > Radar Setup > Installation > Antenna Configuration > Antenna Size, and select the antenna size. Front-of-Boat Offset The front-of-boat offset compensates for the physical location of the radar scanner on a boat, if the radar scanner does not align with the bow-stern axis. Measuring the Potential Front-of-Boat Offset The front-of-boat offset compensates for the physical location of the radar scanner on a boat, if the radar scanner does not align with the bow-stern axis. 1 Using a magnetic compass, take an optical bearing of a stationary target located within viewable range. 2 Measure the target bearing on the radar. 3 If the bearing deviation is more than +/- 1, set the front-of-

boat offset. Setting the Front-of-Boat Offset Before you can set the front-of-boat offset, you must measure the potential front-of-boat offset. The front-of-boat offset setting configured for use in one radar mode is applied to every other radar mode and to the Radar overlay. 1 From a Radar screen or the Radar overlay, select Menu >

Radar Setup > Installation > Front of Boat. 2 Select Up or Down to adjust the offset. Setting a Custom Park Position If you have more than one radar on your boat, you must be viewing the radar screen for the radar you want to adjust. By default, the antenna is stopped perpendicular to the pedestal when it is not spinning. You can adjust this position. 1 From the radar screen, select Menu > Radar Setup >

Installation > Antenna Configuration > Park Position. 2 Use the slider bar to adjust the position of the antenna when stopped, and select Back. Specifications Dimensions Item Measurement 185.9 mm (75/16 in.) Center of rotation to the rear of the pedestal 234.7 mm (91/4 in.) Center of rotation to the front of the pedestal Description 4 Item Measurement 86 mm (325/64 in.) 114 mm (41/2 in.) 200 mm (77/8 in.) Description Center of rotation to the rear mounting holes Center of rotation to the front mounting holes Distance between the mounting holes Item Measurement 4 ft. models: 132.8 cm (4 ft. 45/16 in.) 6 ft. models: 193.8 cm (6 ft. 45/16 in.) 40.3 cm (157/8 in.) 28.6 cm (111/4 in.) 36.4 cm (145/16 in.) Description Antenna length Base of the pedestal to the top of the antenna Width of the pedestal at the base Width of the pedestal in the center Physical Specifications Specification Minimum safe operating distance*

Compass-safe distance Pedestal weight Antenna weight Power cable length Network cable length Antenna rotation speed Maximum wind load Temperature range Humidity Water resistance Bearing accuracy Measurement 4 ft. antenna 10 W/m2: 1.26 m (49.5 in.) 100 W/m2: 3.99 m (157 in.) 6 ft. antenna 10 W/m2: 1.59 m (61 in.) 100 W/m2: 5.03 m (198 in.) 305 mm (12 in.) 15.7 kg (34.7 lb.) 4 ft. antenna: 5.2 kg (11.4 lb.) 6 ft. antenna: 7.3 kg (16.0 lb.) 15 m (49 ft. 3 in.) 15 m (49 ft. 3 in.) 24 rpm and 48 rpm 80 kn From -15 to 55C (from 5 to 131F) 95% at 35C (95F) IEC 60529 IPX6 (protected against heavy seas) 0.25 degrees

*When it is transmitting, the radar should be located in a position on the vessel that is at least this far from people. IEC 60936-1, clause 3-27.1, specifies the maximum distances from the antenna at which radio frequency (RF) levels can be expected. Electrical Specifications Specification Input voltage Fuse Input power Measurement From 10 to 32 Vdc 15 A, blade-type Typical: 55 W Maximum: 160 W Antenna Specifications Specification Type Horizontal beam width Horizontal side lobes Vertical beam width Polarization Measurement End-fed slotted waveguide 4 ft. antenna: 1.8 degrees 6 ft. antenna: 1.25 degrees

-23 dB within 10 degrees of main

-30 dB outside 10 degrees of main 22 degrees Horizontal Installation Troubleshooting Symptom The radar does not turn on. The status LED is not on. Possible Causes The power cable may not be connected correctly to the device or to the battery. Check all connections. The inline fuse may have blown. Check the fuse and replace it if necessary. The wire gauge used to extend the power cable may be too small for the length of the extension. Check the table provided in the Power Cable Extensions section of these instructions to make sure the correct wire gauge is used (Power Cable Extensions, page 3). The radar may not be powering on. Check the status LED. The device software may not be up-to-date. Update the software on the device or on the Garmin Marine Network. The network cable may not be connected correctly to the device or to the Garmin Marine Network. Check all connections. If a field-installable network connector was used, it may have been installed improperly. Check the connector. The radar is not available on the Garmin device or on devices connected to the Garmin Marine Network. The status LED is located on the product label, and can help troubleshoot installation problems. Status LED Color and Activity Solid red Radar Status Flashing green Flashing orange Flashing red The radar is getting ready for use. The LED should be solid red briefly and change to flashing green. The radar is operating properly. The radar software is being updated. The radar has encountered an error. Contact Garmin product support for assistance. Garmin and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GMR and A02546 are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. 5 2016 Garmin Ltd. or its subsidiaries www.garmin.com/support

Important Safety and Product Information............................................................................................................................................................................................................ 2 Informations importantes sur le produit et la scurit........................................................................................................................................................................................... 3 December 2014 20132014 Garmin Ltd. or its subsidiaries Printed in Taiwan Important Safety and Product Information WARNING Failure to avoid the following potentially hazardous situations could result in an accident or collision resulting in death or serious injury. Marine Operation Warnings You are responsible for the safe and prudent operation of your vessel. This device is a tool that will enhance your capability to operate your vessel. It does not relieve you from the responsibility of safely operating your vessel. Avoid navigational hazards and never leave the helm unattended. Use this device only as a navigational aid. Do not attempt to use the device for any purpose requiring precise measurement of direction, distance, location, or topography. Always be prepared to promptly regain control of the vessel. Use caution near hazards in the water, such as docks, pilings and other vessels. If the device has navigating capabilities, when navigating, carefully compare information displayed on the device to all available navigation sources, including information from visual sightings, local waterway rules and restrictions, and maps. For safety, always resolve any discrepancies or questions before continuing navigation. If the device uses maps, use the electronic chart in the device only to facilitate, not to replace, the use of authorized government charts. Official government charts and notices to mariners contain all information needed to navigate safely. If the device provides depth data, it should not be used as the primary means of preventing grounding or collision. Supplement depth data readings with information from applicable paper charts and visual indicators. Always operate the vessel at slow speeds if you suspect shallow water or submerged objects. Failure to heed this warning could lead to vessel damage or personal injury. If the device has video input capabilities, do not attempt to operate or watch video input while operating or navigating your vessel. Operating or watching the video input while the vessel is moving could cause an accident or collision resulting in property damage, serious injury, or death. Battery Warnings The device uses an internal, non-user-replaceable battery for various purposes, such as the real-time clock. If these guidelines are not followed, batteries may experience a shortened life span or may present a risk of damage to the device, fire, chemical burn, electrolyte leak, and/or injury. Do not remove or attempt to remove the non-user-replaceable battery. Contact your local waste disposal department to dispose of the device/batteries in accordance with applicable local laws and regulations. Product Environmental Programs Information about the Garmin product recycling program and WEEE, RoHS, REACH, and other compliance programs can be found at www.garmin.com/aboutGarmin/environment. Declaration of Conformity Hereby, Garmin declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. To view the full Declaration of Conformity, go to www.garmin.com/compliance. Industry Canada Compliance Category I radiocommunication devices comply with Industry Canada Standard RSS-210. Category II radiocommunication devices comply with Industry Canada Standard RSS-Gen. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency Radiation Exposure This device is a mobile transmitter and receiver that uses an internal antenna to send and receive low levels of radio frequency (RF) energy for data communications. The device emits RF energy below the published limits when operating in its maximum output power mode and when used with Garmin authorized accessories. To comply with RF exposure compliance requirements, the device should be installed and operated with a minimum of 530 cm (208.66 in.) between the device and your body. The device should not be used in other configurations. This device must not be co-located or operated in conjunction with any other transmitter or antenna. 2 Increase the separation between the equipment and the receiver. FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet that is on a different circuit from the GPS device. Consult the dealer or an experienced radio/TV technician for help. This product does not contain any user-serviceable parts. Repairs should only be made by an authorized Garmin service center. Unauthorized repairs or modifications could result in permanent damage to the equipment, and void your warranty and your authority to operate this device under Part 15 regulations. Software License Agreement BY USING THE DEVICE, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY. Garmin Ltd. and its subsidiaries ("Garmin") grant you a limited license to use the software embedded in this device (the

"Software") in binary executable form in the normal operation of the product. Title, ownership rights, and intellectual property rights in and to the Software remain in Garmin and/or its third-party providers. You acknowledge that the Software is the property of Garmin and/or its third-party providers and is protected under the United States of America copyright laws and international copyright treaties. You further acknowledge that the structure, organization, and code of the Software, for which source code is not provided, are valuable trade secrets of Garmin and/or its third-party providers and that the Software in source code form remains a valuable trade secret of Garmin and/or its third-party providers. You agree not to decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to human readable form the Software or any part thereof or create any derivative works based on the Software. You agree not to export or re-export the Software to any country in violation of the export control laws of the United States of America or the export control laws of any other applicable country. Map Data Information Garmin uses a combination of governmental and private data sources. Virtually all data sources contain some inaccurate or incomplete data. In some countries, complete and accurate map information is either not available or is prohibitively expensive. Limited Warranty This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will, at its sole option, repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. This warranty does not apply to: (i) cosmetic damage, such as scratches, nicks and dents; (ii) consumable parts, such as batteries, unless product damage has occurred due to a defect in materials or workmanship; (iii) damage caused by accident, abuse, misuse, water, flood, fire, or other acts of nature or external causes; (iv) damage caused by service performed by anyone who is not an authorized service provider of Garmin; or (v) damage to a product that has been modified or altered without the written permission of Garmin, or (vi) damage to a product that has been connected to power and/or data cables that are not supplied by Garmin. In addition, Garmin reserves the right to refuse warranty claims against products or services that are obtained and/or used in contravention of the laws of any country. Our navigation products are intended to be used only as a travel aid and must not be used for any purpose requiring precise measurement of direction, distance, location or topography. Garmin makes no warranty as to the accuracy or completeness of map data. Repairs have a 90 day warranty. If the unit sent in is still under its original warranty, then the new warranty is 90 days or to the end of the original 1 year warranty, depending upon which is longer. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS, IMPLIED, OR STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. IN NO EVENT SHALL Garmin BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. Garmin retains the exclusive right to repair or replace (with a new or newly-overhauled replacement product) the device or software or offer a full refund of the purchase price at its sole discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. To obtain warranty service, contact your local Garmin authorized dealer or call Garmin Product Support for shipping instructions and an RMA tracking number. Securely pack the device and a copy of the original sales receipt, which is required as the proof of purchase for warranty repairs. Write the tracking number clearly on the outside of the package. Send the device, freight charges prepaid, to any Garmin warranty service station. Online Auction Purchases: Products purchased through online auctions are not eligible for rebates or other special offers from Garmin warranty coverage. Online auction confirmations are not accepted for warranty verification. To obtain warranty service, an original or copy of the sales receipt from the original retailer is required. Garmin will not replace missing components from any package purchased through an online auction. International Purchases: A separate warranty may be provided by international distributors for devices purchased outside the United States depending on the country. If applicable, this warranty is provided by the local in-country distributor and this distributor provides local service for your device. Distributor warranties are only valid in the area of intended distribution. Devices purchased in the United States or Canada must be returned to the Garmin service center in the United Kingdom, the United States, Canada, or Taiwan for service. Marine Warranty Policy: Certain Garmin Marine products in certain areas have a longer warranty period and additional terms and conditions. Go to www.garmin.com/support/warranty.html for more details and to see if your product is covered under the Garmin Marine Warranty Policy. Australian Purchases: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits under our Limited Warranty are in addition to other rights and remedies under applicable law in relation to the products. Garmin Australasia, 30 Clay Place, Eastern Creek, NSW, Australia, 2766. Phone: 1800 235 822. Informations importantes sur le produit et la scurit AVERTISSEMENT Si vous ne prenez pas de prcautions pour viter les situations potentiellement dangereuses nonces ci-aprs, vous risquez un accident ou une collision pouvant entraner des blessures graves, voire mortelles. Avertissements d'utilisation en milieu marin Vous tes responsable de l'utilisation sre et prudente de votre bateau. Cet appareil est un outil qui optimisera votre capacit de pilotage. Il ne vous dgage pas de vos responsabilits en cas de non-respect de la scurit bord. Evitez tout danger de navigation et ne relchez pas votre surveillance de la barre. L'appareil doit tre utilis uniquement comme une aide la navigation. Ne tentez pas d'utiliser l'appareil des fins exigeant une mesure prcise de l'orientation, de la distance, de la position ou de la topographie. Soyez toujours prt reprendre les commandes du navire. Soyez vigilant proximit des points dangereux, tels que les quais et les autres navires. En cours de navigation, et si l'appareil dispose de fonctions de navigation, comparez attentivement les informations affiches par l'appareil toutes les autres sources d'information disponibles, notamment les repres visuels, les rgles et restrictions locales relatives aux voies navigables, ainsi que les cartes. Pour votre scurit, cherchez rsoudre tout dysfonctionnement ou problme avant de poursuivre la navigation. Si l'appareil utilise des cartes, utilisez la carte lectronique de l'appareil uniquement pour faciliter l'usage de cartes gouvernementales officielles, pas pour les remplacer. Seules les cartes gouvernementales officielles et les avis aux navigateurs contiennent toutes les informations ncessaires une navigation en toute scurit. Si l'appareil fournit des donnes de profondeur, celles-ci ne doivent pas tre utilises en premier recours afin d'viter les risques d'chouage ou de collision. Compltez les mesures des donnes de profondeur l'aide d'informations issues de cartes papier et d'indicateurs visuels applicables. Si vous suspectez la prsence d'un haut-fond ou d'objets immergs, naviguez toujours faible vitesse. L'ignorance de cet avertissement vous expose des risques de dtrioration du navire ou de blessures. Si l'appareil dispose de fonctions d'entre vido, n'utilisez pas l'entre vido en cours de navigation. Le visionnage de la vido lorsque le navire se dplace peut engendrer un accident ou une collision provoquant des dommages matriels et des blessures graves, voire mortelles. Avertissements relatifs la batterie L'appareil utilise une batterie interne, non remplaable par l'utilisateur, pour diffrentes raisons telles que celle de l'horloge en temps rel. Le non-respect de ces consignes peut causer une diminution de la dure de vie des batteries, endommager l'appareil ou prsenter un risque d'incendie, de brlure chimique, de fuite d'lectrolyte et/ou de blessure. N'essayez pas de retirer la batterie non remplaable par l'utilisateur. Contactez la dchetterie locale pour plus d'informations sur la mise au rebut de l'appareil ou des batteries dans le respect des lois et rglementations locales applicables. Programmes environnementaux Des informations relatives au programme Garmin de recyclage des produits ainsi qu'aux directives DEEE et RoHS, la rglementation REACH et aux autres programmes de conformit sont disponibles l'adresse www.garmin.com/aboutGarmin

/environment. Dclaration de conformit Par la prsente, Garmin dclare que ce produit est conforme aux principales exigences et autres clauses pertinentes de la directive europenne 1999/5/CE. Pour prendre connaissance de l'intgralit de la dclaration de conformit, rendez-vous sur le site www.garmin.com/compliance. Conformit aux normes d'Industrie Canada Les priphriques de radiocommunication de catgorie I sont conformes la norme RSS-210 d'Industrie Canada. Les priphriques de radiocommunication de catgorie II sont conformes la norme RSS-Gen d'Industrie Canada. Cet appareil est conforme aux normes RSS sans licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) ce priphrique ne doit pas causer d'interfrences et (2) doit accepter toute interfrence, y compris les interfrences pouvant entraner un fonctionnement indsirable de l'appareil. Contrat de licence du logiciel EN UTILISANT CE PRODUIT, VOUS RECONNAISSEZ ETRE LIE PAR LES TERMES DU PRESENT CONTRAT DE LICENCE DE LOGICIEL. LISEZ ATTENTIVEMENT CE CONTRAT DE LICENCE. Garmin Ltd. et ses filiales ( Garmin ) concdent une licence limite pour l'utilisation du logiciel intgr cet appareil (le Logiciel ) sous la forme d'un programme binaire excutable, dans le cadre du fonctionnement normal du produit. Tout titre, droit de proprit ou droit de proprit intellectuelle dans le Logiciel ou concernant le Logiciel est la proprit de Garmin et/ou de ses fournisseurs tiers. Vous reconnaissez que le Logiciel est la proprit de Garmin et/ou de ses fournisseurs tiers et qu'il est protg par les lois en vigueur aux Etats-Unis d'Amrique et par les traits internationaux relatifs aux droits d'auteur. Vous reconnaissez galement que la structure, l'organisation et le code du Logiciel, dont le code source n'est pas fourni, constituent d'importants secrets de fabrication de Garmin et/ou de ses fournisseurs tiers, et que le code source du Logiciel demeure un important secret de fabrication de Garmin et/ou de ses fournisseurs tiers. Vous acceptez de ne pas dcompiler, dsassembler, modifier, assembler rebours, tudier par rtro-ingnierie ou transcrire en langage humain intelligible le Logiciel ou toute partie du Logiciel, ou crer toute uvre drive du Logiciel. Vous acceptez de ne pas exporter ni de rexporter le Logiciel vers un pays contrevenant aux lois de contrle l'exportation des Etats-Unis d'Amrique ou celles de tout autre pays concern. Informations sur les donnes cartographiques Les donnes de Garmin proviennent la fois de sources publiques et prives. La quasi-totalit des sources de donnes contient une part d'informations inexactes ou incompltes. Dans certains pays, des informations cartographiques compltes et exactes sont soit indisponibles, soit proposes un cot prohibitif. Garantie limite Ce produit Garmin est garanti contre tout dfaut de matriel et de fabrication pendant un an compter de sa date d'achat. Durant cette priode, Garmin pourra, son entire discrtion, rparer ou remplacer tout composant qui s'avrerait dfectueux dans le cadre d'un usage normal. Ce type de rparation ou de remplacement ne sera pas factur au client, qu'il s'agisse des composants ou de la main-d'uvre, condition que le client prenne en charge les frais de port. Cette garantie ne couvre pas : (i) les dommages esthtiques, tels que les raflures, les rayures et les bosses ; (ii) les consommables, comme les piles, moins que le dommage ne soit d un dfaut matriel ou de fabrication ; (iii) les dommages provoqus par un accident, 3 une utilisation abusive, une mauvaise utilisation, l'eau, une inondation, un incendie ou toute autre catastrophe naturelle ou cause extrieure ; (iv) les dommages provoqus par des fournisseurs de services non agrs par Garmin ; ou (v) les dommages sur un produit ayant t modifi sans l'autorisation crite de Garmin ; ou (vi) les dommages sur un produit raccord des cbles d'alimentation et/ou des cbles de donnes non fournis par Garmin. En outre, Garmin se rserve le droit de refuser toute demande de service sous garantie relative un produit ou service obtenu et/ou utilis en violation des lois de tout pays. Nos produits de navigation constituent uniquement une aide la navigation et ne doivent pas tre utiliss des fins exigeant l'valuation prcise de la direction, de la distance, de la position ou de la topographie. Garmin n'offre aucune garantie quant l'exactitude ou l'exhaustivit des donnes cartographiques. Les rparations sont garanties pendant 90 jours. Si l'unit envoye est toujours couverte par la garantie d'origine, cette nouvelle garantie court pendant un dlai de 90 jours ou jusqu' la fin de la priode de garantie d'origine qui est d'un an, selon la plus longue des deux priodes. LES GARANTIES ET RECOURS CONTENUS DANS LE PRESENT DOCUMENT SONT EXCLUSIFS ET ANNULENT TOUTE AUTRE GARANTIE EXPRESSE, IMPLICITE OU LEGALE, Y COMPRIS TOUTE RESPONSABILITE RESULTANT DE TOUTE GARANTIE DE QUALITE MARCHANDE OU D'ADEQUATION A UN USAGE PARTICULIER, QU'ELLE SOIT LEGALE OU AUTRE. CETTE GARANTIE VOUS OCTROIE DES DROITS PARTICULIERS, QUI PEUVENT VARIER D'UN ETAT A L'AUTRE. EN AUCUN CAS, LA SOCIETE Garmin NE SAURAIT ETRE TENUE RESPONSABLE DE TOUT DOMMAGE ACCESSOIRE, SPECIAL, INDIRECT OU CONSECUTIF RESULTANT DE L'UTILISATION, DE LA MAUVAISE UTILISATION OU DE L'IMPOSSIBILITE D'UTILISER CE PRODUIT, OU RESULTANT DE DEFAUTS DU PRODUIT. CERTAINS ETATS INTERDISANT L'EXCLUSION OU LA RESTRICTION DES DOMMAGES ACCESSOIRES OU CONSECUTIFS, LES RESTRICTIONS SUSMENTIONNEES PEUVENT NE PAS VOUS CONCERNER. Garmin se rserve le droit exclusif de rparer l'appareil ou le logiciel, de les remplacer (par un produit de remplacement neuf ou entirement rvis) ou de proposer le remboursement intgral du prix d'achat son entire discrtion. CE TYPE DE RECOURS SERA VOTRE RECOURS UNIQUE ET EXCLUSIF POUR TOUTE RUPTURE DE GARANTIE. Pour bnficier d'un service sous garantie, contactez votre revendeur agr Garmin ou appelez le service d'assistance produit de Garmin pour obtenir les instructions relatives l'expdition du produit, ainsi qu'un numro de suivi RMA. Emballez avec soin l'appareil en y joignant une copie de l'original de la facture, qui fera office de preuve d'achat dans le cas de rparations sous garantie. Inscrivez lisiblement le numro de suivi sur l'extrieur du paquet. Envoyez le priphrique, frais de port prpays, un centre de services sous garantie Garmin. Achats dans le cadre d'enchres en ligne : les produits achets au cours d'enchres en ligne ne peuvent faire l'objet de rabais ou d'autres offres spciales proposs par la garantie de Garmin. Les confirmations de vente aux enchres en ligne ne sont pas acceptes dans le cadre d'une vrification sous garantie. Pour bnficier d'un service sous garantie, l'original ou une copie de la facture dresse par le premier revendeur doit tre prsent. Garmin ne procdera aucun remplacement de composant manquant sur tout produit achet dans le cadre d'enchres en ligne. Achats internationaux : selon les pays, une garantie distincte peut tre accorde par les distributeurs internationaux pour les appareils achets hors des Etats-Unis. Le cas chant, cette garantie est fournie par le distributeur du pays d'achat et ledit distributeur prend en charge les services locaux ncessaires pour votre appareil. Les garanties distributeur sont valides uniquement dans les zones de distribution vises. En cas de problme, les appareils achets aux Etats-Unis ou au Canada doivent tre renvoys aux ateliers de rparations Garmin du Royaume-Uni, des Etats-Unis, du Canada ou de Tawan. Politique de garantie des produits marine : pour certains produits marine de Garmin de certaines rgions du monde, la priode de garantie est plus longue et des conditions supplmentaires s'appliquent. Rendez-vous sur le site www.garmin.com

/support/warranty.html pour plus de dtails et pour savoir si votre produit est couvert par la garantie des produits marine de Garmin. 4