GWN7600 Wireless Access Point To ensure easy installation and management, the GWN7600 uses a controller-less distributed network management design in which the controller is embedded within the products web user interface. This allows each access point to manage a network of up to 30 GWN76xx series APs independently without needing separate controller hardware/software and without a single point-of-failure. This wireless access point can be paired with any third party routers as well as Grandstream GWN series routers. With support for advanced QoS, low-latency real-time applications, 450+ concurrent client devices per AP and dual Gigabit network ports with PoE, the GWN7600 is an ideal WiFi access point for medium wireless network deployments with medium-to-high user density. 1.17Gbps wireless throughput and 2x Gigabit wireline ports Support 802.3af Power-over-Ethernet
(PoE) Support 450+ concurrent WiFi client devices Advanced QoS to ensure real-time performance of low-latency applications Up to 165-meter coverage range Anti-hacking secure boot and critical data/control lockdown via digital signatures, unique security certificate/random default password per device Embedded controller allows GWN7600 to auto-discover, auto-provision and manage up to 30 GWN7600s in a network info@grandstream.com www.grandstream.com Specifications WiFi Standards IEEE 802.11 a/b/g/n/ac (Wave-2) Antennas 2x 2.4 GHz, gain 3 dBi, internal antenna 2x 5 GHz, gain 3 dBi, internal antenna IEEE 802.11ac: 6.5 Mbps to 877 Mbps IEEE 802.11a: 6, 9, 12, 18, 24, 36, 48, 54 Mbps IEEE 802.11n: 6.5 Mbps to 300 Mbps IEEE 802.11b: 1, 2, 5.5, 11 Mbps IEEE 802.11g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps WiFi Data Rates
*Actual throughput may vary depending on many factors including environmental conditions, distance between devices, radio interference in the operating environment and mix of devices in the network Frequency Bands 2.4GHz radio : 2.412 - 2.462 GHz 5GHz radfio: 5.150 - 5.250 GHz, 5.725-5.850 GHz Channel Bandwidth 2.4G: 20 and 40 MHz 5G: 20,40 and 80 MHz WiFi and System Security WEP, WPA/WPA2-PSK, WPA/WPA2 Enterprise (TKIP/AES), anti-hacking secure boot and critical data/control lockdown via digital signatures, unique security certificate and random default password per device MIMO 2x2:2 2.4GHz (MIMO), 2x2:2 5GHz (MU-MIMO) Coverage Range Up to 541 ft. (165 meters) Maximum TX Power 5G: 802.11a:22.53dBm,802.11n-HT20:22.36dBm;802.11n-HT40:22.38dBm;802.11ac20:22.34dBm 802.11ac40:22.30dBm;802.11ac80:22.15dBm;
2.4G: 802.11b:17.69dBm;802.11g:19.78dBm,802.11n-HT20:19.62dBm;802.11n-HT40:19.64dBm;
2.4G: 802.11b:20.14dBm;802.11g:22.40dBm,802.11n-HT20:22.14dBm;802.11n-HT40:22.0dBm;
Receiver Sensitivity 2.4G 802.11b:-99dBm @1Mbps,-91dBm @11Mbps;802.11g:-93dBm @6Mbps,-75dBm @54Mbps;
80.11n 20MHz:-72dBm @MCS7;802.11n 40MHz:-69dBm @MCS7 5G 802.11a:-91dBm @6Mbps,-74dBm @54Mbps;802.11ac 20MHz:-67dBm @MCS8;802.11ac HT40:-63dBm @MCS9;802.11ac 80MHz:-60dBm @MCS92 SSIDs 16 SSIDs per radio Concurrent Clients 450+
Network Interfaces 2x autosensing 10/100/1000 Base-T Ethernet Ports Auxiliary Ports 1x USB 2.0 port, 1x Reset Pinhole, 1x Kensington lock Mounting Indoor wall mount or ceiling mount, kits included LEDs 3 tri-color LEDs for device tracking and status indication Network Protocols IPv4, 802.1Q, 802.1p, 802.1x, 802.11e/WMM QoS 802.11e/WMM, VLAN, TOS Network Management Embedded controller in GWN7600 allows it to auto-discover, auto-provision and manage up to 30 GWN7600s in a network Power and Green Energy Efficiency Environmental DC Input: 24VDC/1A Power over Ethernet (802.3af) compliant Maximum Power Consumption:13.8W Operation:-20C to 40C Storage: -10C to 60C Humidity: 10% to 90% Non-condensing Physical Unit Dimension: 205.3 x 205.3 x 45.9mm; Unit Weight: 526g Unit + Mounting Kits Dimension : 205.3 x 205.3 x 53.9mm; Unit + Mounting Kits Weight : 610g Entire Package Dimension: 228.5 x 220 x 79mm; Entire Package Weight: 854g Package Content GWN7600 Wave-2 802.11ac Wireless AP, Mounting Kits, Quick Start Guide Compliance FCC, CE, RCM, ISEDC www.grandstream.com EN OVERVIEW To ensure easy installation and management, the GWN7600 uses a controller-less distrib-
uted network management design in which the controller is embedded within the products web user interface. This allows each access point to manage a network of up to 30 GWN7600 series APs independently without needing separate controller hardware/software and with-
out a single point-of-failure. This wireless access point can be paired with any third party routers as well as Grandstream GWN series routers. With support for advanced QoS, low-latency real-time applications, 450+ concurrent client devices per AP and dual Gigabit network ports with PoE, the GWN7600 is an ideal WiFi access point for medium wireless network deployments with medium-to-high user density. PRECAUTIONS Do not attempt to open, disassemble, or modify the device. Do not expose this device to temperatures outside range of -20C to 40 C. Do not expose the GWN7600 to environments outside of the following humidity range:
10-90% RH (non-condensing). Do not power cycle your GWN7600 during system boot up or firmware upgrade. You may corrupt firmware images and cause the unit to malfunction. PACKAGE CONTENTS GWN7600 Access Point Mounting Bracket 1 x Quick Installation Guide 1 x GPL Statement Ceiling Mounting Bracket 3 x Plastic Expansion Bolt 3 x M3 NUT 3 x Screw (PM 3.0 x 50) 3 x Screw (PA 3.5 x 20 ) GWN7600 PORTS Port POWER NET/POE NET RESET Description Power adapter connector (DC24V, 1A) Note: Power adapter is not provided. Ethernet RJ45 port (10/100/1000Mbps) supporting PoE. Ethernet RJ45 port (10/100/1000Mbps) to your router or another GWN76xx. USB 2.0 port (for future IOT & location based applications) Factory reset button. Press for 7 seconds to reset factory default settings. HARDWARE INSTALLATION GWN7600 can be mounted on the wall or ceiling, Please refer to the following steps for the appropriate installation. Wall Mount 1. Position the mounting bracket at the desired location on the wall with the arrow pointing up. 2. Use a pencil to mark the four mounting holes (screw holes DIA 5.5mm, reticle hole DIA 25mm). 3. Insert screw anchors into the 5.5 mm holes. Attach the mounting bracket to the wall by inserting the screws into the anchors. 4. Connect the power cable and the ethernet cable (RJ45) to the correct ports of your GWN7600. 5. Align the arrow on the GWN7600 with the arrow on the locking tab of the mounting bracket and ensure that your GWN7600 is frmly seated on the mounting bracket. 6.Turn the GWN clockwise until it locks into place and fits the locking tab. Ceiling Mount 1. Remove the ceiling tile. 2. Place the ceiling backing plate in the center of the ceiling tile and mark the mounting screw holes (screw holes DIA 5.5mm, reticle hole DIA 25mm). 3. Insert the screws through the mounting bracket. Ceiling Mounting Bracket M3 nut M3.0x50 screw 4. Connect the power cable and the Ethernet cable (RJ45) to the correct ports of your GWN7600. POWERING AND CONNECTING THE GWN7600 GWN7600 can be powered on using PoE switch using following steps:
Step 1: Plug a RJ45 Ethernet cable into the network port of the GWN7600 Step 2: Plug the other end into the uplink port of the power over Ethernet (PoE) switch. Network Port RJ45 Ethernet Cable to Power over Ethernet
(PoE) Switch 5. Align the arrow on the GWN7600 with the arrow on the locking tab of the mounting bracket and ensure that your GWN is firmly seated on the mounting bracket and connect bracket and ensure that your GWN7600 is firmly seated on the mounting bracket and connect the network and power cables. 6.Turn the GWN clockwise until it locks into place and fits the locking tab. Note: Ceiling mounting is recommended for optimal coverage performance. CONNECT TO GWN7600 DEFAULT WIFI NETWORK GWN7600 can be used as standalone access point out of box, or after factory reset with Wi-Fi enabled by default. After powering the GWN7600 and connecting it to the network, GWN7600 will broadcast a default SSID based on its MAC address GWN[MACs last 6 digits] and a random password. Note: GWN7600s default SSID and password information are printed on the MAC tag of the unit. ACCESSING THE CONFIGURATION INTERFACE A computer connected to the GWN7600s SSID, or to the same network as the GWN7600 can discover and access its configuration interface using one of the below methods:
Method 1: Discover GWN7600 using its MAC Address. 1. Locate the MAC address on the MAC tag of the unit, which is on the underside of the device, or on the package. 2. From a computer connected to same network as the GWN7600, type in the following address using the GWN7600s MAC address on your browser https://gwn_<mac>.local Example: if a GWN7600 has the MAC address 00:0B:82:8B:4E:28, this unit can be ac-
cessed by typing https://gwn_000b828b4e28.local on the browser. Method 2: Discover GWN7600 using GWN DiscoveryTool. 1. Download and install GWN DiscoveryTool from the following link:
http://www.grandstream.com/support/tools 2. Open the GWN DiscoveryTool, and click on Scan. 3. The tool will discover all GWN7600 Access Points connected on the network showing their MAC and IP addresses. 4. Click on Manage Device to be redirected directly to the GWN7600s configuration inter-
face, or type in manually the displayed IP address on your browser. Using one of the above methods, the login screen will appear. Type in admin in both Username and Password fields and click on Sign In. Notes :
- Make sure that the GWN7600 is not already paired with another GWN7600/GWN7610 Access Point as slave, otherwise the configuration interface cannot be accessed.
- If the GWN7600 is already paired, make sure to unpair it first, or do a factory reset.
- For more information, please download the GWN7600 User Manual from:
http://www.grandstream.com/support FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ISEDC Warning This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. applicablesauxappareilsradioexemptsde LeprsentappareilestconformeauxCNRd'Innovation,SciencesetDveloppement conomiqueCanada licence.L'exploitationestautoriseauxdeuxconditionssuivantes:
(1)l'appareilnedoitpasproduiredebrouillage,et
(2)l'utilisateurdel'appareildoitacceptertoutbrouillageradiolectriquesubi,mme silebrouillageestsusceptibled'encompromettrelefonctionnement. ISEDC RF exposure statement :
This equipment complies with IS radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux ISEDC RF limites d'exposition aux radiations dans un environnement non contrl. Cet metteur ne doit pas tre situ ou oprant en conjonction avec une autre antenne ou metteur. Cet quipement est conforme aux ISED RF limites d'exposition aux radiations dans un