FCC ID: Z6QFX12924GTX Sharper Image DX-3 Video Drone

Rechargeable 2.4GHz DX-3 VIDEO DRONE Rechargeable 2.4GHz DX-3 VIDEO DRONE Rechargeable 2.4GHz DX-3 VIDEO DRONE 12+

SPECIFICATIONS READ ALL WARNINGS AND PRECAUTIONS BEFORE USE GETTING TO KNOW YOUR DRONE PLEASE READ ALL WARNINGS AND INSTRUCTIONS PRIOR TO USE. KEEP THIS DOCUMENT AS IT CONTAINS IMPORTANT INFORMATION ABOUT YOUR DRONE. 1. Turn your drone on and place on a flat, level surface 2. Turn on the remote on and move the left joystick down, then up, then down again 3. The beep will indicate successful pairing 1. CHARGING Drone must be charged before each use (USB cable included) Indicator light will turn off once fully charged Install batteries in remote 2. PAIRING Before each flight pair the remote with the drone:

3. DIRECTIONAL LIGHTS White lights indicate the front of the drone Red lights indicate the back of the drone Not applicable in auto-orientation mode 4. REMOTE CONTROL OVERVIEW Practice flying your drone below 10 feet and at low speeds until comfortable with all controls to avoid unncessary damage or injury To cut power to drone, move left joystick to down position Left joystick:

Right joystick: controls flight direction Direction Trim: use to eliminate drift Up/Down controls elevation Left/Right controls spin QUESTIONS OR CONCERNS?

PLEASE GIVE US A CALL ... WERE HERE TO HELP CUSTOMER SERVICE

(800) 374-2744 Before calling please locate the 10-digit code printed on the back of your remote CHOKING HAZARD SMALL PARTS NOT FOR CHILDREN UNDER 3 YEARS. ADULT ASSEMBLY REQUIRED. INTRODUCTION Congratulations on your purchase of the Sharper Image Rechargeable 2.4 GHz DX-3 Video Drone. Get ready to soar to new heights. Master the art of drone flying and stunting with remote control maneuverability. This lightweight stunting drone will provide hours of fun. Drone Battery: 800 mAh Li-po Remote Controller Battery: 6 x 1.5V AA Charging Time: Approximately 120 minutes Maximum Recommended Altitude 150 ft. TABLE OF CONTENTS General Warnings Contents and Remote Battery Installation Charging LiPo and Replacing Propellers Remote Overview Operating Drone Modes and Installing Blade Gaurds Tips and FCC Warning Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Prevent contact with spinning blades by turning off remote prior to handling drone Not recommended for children under 12 years of age. As with all electrical products, precaution should be observed during handling and use to reduce the risk of electrical shock. Adult supervision is required at all times Before each use, an adult should review the product and battery to determine that no damage or hazards exist DO NOT TOUCH SPINNING PROPELLERS Do not allow anything to intentionally make contact in any way with spinning propellers Use caution and pay attention to your surroundings while operating drone Do not fly drone into animals, people, or inanimate objects Keep drone away from power lines, buildings, trees, public areas, and any other potentially hazardous areas. Do not operate in rain, heavy wind, and or any type of severe weather Do not land drone on wet surfaces Never touch or allow others to touch drone while it is flying Always turn drone off when it is not in use Always fly drone in large open areas SAFETY WARNINGS:

Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes. Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others. The drone shall never be modified or used for anything except its intended purpose. PLEASE RECYCLE OR DISPOSE OF ELECTRONICS PROPERLY RECYCLING INFORMATION IS AVAILABLE AT WWW.MERCHSOURCE.COM Invasion of Privacy Warning Always be mindful of others privacy and do not record video or take images of others without their consent. Check and comply with your federal, state and local laws regarding privacy. Page i Page 1 Rechargeable 2.4GHz DX-3 VIDEO DRONE Rechargeable 2.4GHz DX-3 VIDEO DRONE Rechargeable 2.4GHz DX-3 VIDEO DRONE CONTENTS MicroSD 4GB Card 3 DX-3 Video Drone MicroSD Card Reader AUTO ORIENTATION H M L LAND SPIN TRIM DIRECTION TRIM 3 Drone Controller USB Connector Blade Guards &

8 Screws Replacement Propellors REMOTE BATTERY INFORMATION 1. Slide open battery compartment 2. Install 6 AA batteries as shown in diagram shown above 3. Replace and close battery compartment LITHIUM-POLYMER BATTERY WARNING There is a risk of fire and personal injury if Li-Po battery is punctured, damaged or misused Never expose battery to extreme temperatures or moisture Do not subject battery to strong impacts Always keep battery away from flammable materials Only use manufacturer specified batter(ies), charger(s), and/or adapters, if applicable, specified by the manufacturer Battery is not serviceable Let battery cool to room temperature before charging While charging, never leave battery unattended Recycle or dispose of battery according to federal, state and local laws KEEP THIS INSTRUCTION MANUAL FOR REFERENCE BATTERY WARNING Do not mix old and new batteries Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries Insert batteries using the correct polarity. Do not short-circuit the supply terminal Only use manufacturer specied batter(ies), charger(s), and/or adapters, if applicable, specied by the manufacturer Always use, replace, and recharge (if applicable) batteries under adult supervision KEEP THE PACKAGE FOR REFERENCE AS IT CONTAINS IMPORTANT INFORMATION Page 2 CHARGING BATTERY Note: The Battery Charger will light up when it is charging the battery and turn off when the battery is fully charged. Charge time is approximately 120 minutes. Turn off the drone before charging. Connect the Battery Charger to the Micro USB port on the Drone. Connect USB connector to power source. Connect the Battery Charger to the Drone Insert the USB connector into a USB power source Replacing Propellers 1. Follow diagram 2. Remove screw from top of Propeller 3. Remove broken Propeller and replace with new Propeller 4. Make sure you installed the correct blade. Each blade has a number written on it.Match the blades with the corresponding number on the drone 5. Insert screw into top of Propeller Light indicates remote is on Speed switch Forward adjustment Stunt button Throttle Joystick Increases or decreases drone elevation Use L/R arrows for spin Spin adjustment:

Slide left to spin drone counterclockwise and slide right to spin drone clockwise ON/OFF Remote switch Backwards adjustment Camera Video Multi Direction Joystick AUTO ORIENTATION H M L LAND SPIN TRIM 3 DIRECTION TRIM Right adjustment Left adjustment Page 3 Auto land Auto orientation Page 4 Rechargeable 2.4GHz DX-3 VIDEO DRONE Rechargeable 2.4GHz DX-3 VIDEO DRONE Rechargeable 2.4GHz DX-3 VIDEO DRONE OPERATING DRONE Step 1 Pre Flight Checklist 1. Read all warnings and instructions 2. Install remote batteries, page 2 3. Make sure that drone and remote are powered off 4. Assemble Drone, page 3. 5. Charge batteries, page 3. Step 2 Choosing a location Drone is designed to be flown indoors and outdoors Always make sure you have enough space to fly drone Always follow warnings, page 1 Step 3 Starting Drone 1. Making sure your remote is off, slide drone switch to ON. Drone lights will begin to flicker 2. Choose a flat even surface and follow the diagram 3. Turn remote on. Bring the Throttle all the way up then bring it all the way down. Remote will beep and drone lights will flicker rapidly then turn on permanently once paired. 4. Drone is ready for flight. Step 4 Lift Off 1. Slowly and carefully press the Throttle Joystick up. Drone will begin to elevate. You can compensate for some of the drones drifting by using the Multi Directional Button or by following step 5. You may need to practice this step several times before successfully getting drone into the air. 2. You can let go of the throttle once you get to your desired elevation. The drone will engage its auto hover function. 10 FEET 10 FEET 5 FEET 10 FEET 10 FEET Drone drifts backwards: Press the forward Adjustment Drone drifts forwards: Press the Backwards Adjustment Step 5 Drone Begins to Drift Follow this step if your drone begins to drift while take off or during flight Button Button Spin Adjustment to the left Slide the Spin Adjustment to the right Drone drifts left: Press the Right Adjustment Button Drone drifts right: Press the Left Adjustment Button Drone spins clockwise (viewing drone from top): Slide the Drone spins counter-clockwise (viewing drone from top):

Step 6 Operating Drone in Flight The drones range is approximately 400 feet or 150 feet of altitude Step 7 Landing Drone There are two ways to land the drone. Read and be aware of all warnings found on page 1. Maintain your desired elevation by using the Throttle Push the Throttle joystick to right or left to spin the drone. Use the Multi Directional Joystick to move forwards, backwards, and side to side Review step 5 if your drone begins to drift Drone will begin to blink when drone is paired to remote and battery is low 1. Press the Auto Land Button. The drone will slowly begin to land. If the drone begins to drift, you can still control the drones direction using the Multi Directional Button. 2. Slowly and carefully press the Throttle Joystick down until drone lands. If the drone begins to drift, you can still control the drones direction using the Multi Directional Button Always turn off remote prior to retrieving or picking up drone. This will help you avoid accidently activating propellers. 1. Hover the drone to at least above 10 feet. 2. Press the Stunt Button. You will hear beeping coming from the remote 3. Move the Multi Directional Button to the desired direction that you would like the drone to flip MODES Stunt Button Once you are comfortable flying the drone, use the Stunt Button to perform acrobatic stunts. Auto Orientation Button Auto Orientation default setting is off. To enter this mode press Auto Orientation + button. Re mote will beep twice. After drone success paired, the 2 white LED lights toward orientation will be the original forward orientation, when drone is in auto orientation mode, whatever the drone spin, the forward orientation will be previous original forward orientation. Remote will beep every 6s to indicate the drone is in Auto Orientation mode. To exit mode, press the + button. Remote will sound 1 long beep indicating that it has exited Auto Orientation mode. Auto Landing Button Make sure you have achieved level, balanced flight, where the drone is neither climbing nor descending.This mode allows you to safely and slowly land your drone without having to control the speed. It is done for you automatically. The ideal auto landing height is 25ft. Press the - button to trigger auto land. Remote will beep continuously until drone lands Do NOT touch the left control stick. This will interrupt the landing sequence. To steer the drone during landing, use the right control until drone has reached the ground. Press the - button again to exit auto landing mode. NOTE: Please make sure the throttle joystick is on down position before exit auto landing mode. Camera taking pictures and creating videos Taking a picture- press Camera Button once to take a picture. 4 main lights will blink once and audible beep heard indicating photo has been taken. Creating video- press Video Button once to take a video. Main lights will blink continuously indicating video is being recorded. Lights will go solid (stop blinking) when video recording has stopped. Please press the video button again to stop the video creating. NOTE: Pictures and video camera cannot be taken at the same time. Please wait for 2s in between pictures. INSTALLING BLADE GAURDS Click blade guards in place per diagrams below. Use provided screws and a small screwdriver to secure the blade gaurds before use. Page 5 TIPS Do not crash drone into sand or dirt. Drone gears may become clogged When first learning to fly, practice lifting off and hovering Stay several feet from walls and buildings Always Press Throttle all the way down after crashing or when something gets stuck in propellers Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes. Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others. The drone shall never be modified or used for anything except its intended purpose. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. TROUBLESHOOTING:

When remote switch is turned on, the remote light does not illuminate:

1) Check that batteries in the remote are installed correctly OR 2) Replace with new batteries During drone flight, the remote LED is flashing:

1) Remote batteries are low; replace them with new batteries Drone and remote properly pair, but the drone will not lift-off:

1) Drone Li-Po needs charging. Use charging cable to connect the drone to power source. After trimming the drone, the drone flight is very unstable and cannot fly properly:

1) One or more blades are most likely damaged;

2) Turn off the drone and remote. 3) Replace with the proper number replacement blade and try flying again. After impact, the drone is unstable:

1) Put the left remote control lever to the left bottom and put the right remote control lever to the right bottom at the same time which connected to the drone (diagram to right). 2) If the above does not resolve the issue, reboot the drone and controller and pair again. Remote Controller and Drone can not be paired:

1) Check Point: Remote Controller must be closed to Drone, not exceed 4 meters. AUTO ORIENTATION LAND SPIN TRIM DIRECTIOIN TRIM Note: If there are 2 sets of Drones within 4 meters for Pairing, you must pair one successfully before pairing the second set. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nications. However there is no guarantee that interference will not occur in a particular installation.

- Reorient or relocate the receiving antenna,

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures:

Sharper Image. All Rights Reserved. SHARPER IMAGE name and logo are registered trademarks manufactured and marketed by MerchSource, LLC under license. All other logos and trademarks are proprietary to their respective owners. The artwork and design of this package are protected by US copyright law and may not be reproduced, distributed, displaced, published or used for any purpose without prior written permission. Altering, removing or reproducing any of the trademark or copyright notices on this package is not permitted. Page 6 2016 MerchSource, LLC. All rights reserved. Distributed by MerchSource, LLC, Irvine, CA 92618. PATENT PENDING Printed in China Page 7

Label Artwork and Location SIZE: 37mm (W) x 22mm (H)

Feb 03, 2016 To whom it may concern, Request for Permanent Confidentiality Under FCC Part 15 Certification me FCC ID: Z6QFX12924GTX Request is hereby submitted by __GUANGDONG FEILUN TECHNOLOGY INDUSTRIAL CO.LTD___ to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, ihe following sections of the application are to be kept permanently confidential and_GUANGDONG FEILUN TECHNOLOGY INDUSTRIAL CO.,LTD reserves the right to discern which parties can obtain access to these information:

Schematics Detailed Block diagrams Detailed Operational/Functional Description The rationale for request for confidentiality is as followings:

This information represents intellectual property of_GUANGDONG FEILUN TECHNOLOGY INDUSTRIAL CO.,LTD and it is subject to competition. We have invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Regards,

[Signature]

Ga shao na

[Name] Cai shaona

[Title] vice president

Guangdong Feilun Technology Industrial Co., Ltd. Mar 08, 2016 To whom it may concern, Letter of Agency

|, an officer of _Guangdong Feilun Technology Industrial Co., Ltd. do hereby authorize Intertek Testing Services (Ms. Stella Yang) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and/or Part 95 of the FCC Rules until further notice.

| further certify that no party (as defined in 1.2002(b) of CFR 47, 2007) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 862. Regards,

[Signature]

Shawna Cas

[Name] Shaona Cai

[Title]

Vice President