FCC ID: SY9-LT509 PKE car alarm system remote

95mm LC680PKE One push start Instructions m m 5 0 1 Remote Buttons description: Because different remotes are with different button icons,please refer to the real remotes. I.PKE Remote button icons:

Arm (Lock) Disarm (Unlock) Select Search II.Button function:

1.Arm (Lock) 1)Press the button " " once, then the siren will sound once, the central control lock door will be locked, the push start button function will be disabled, and the car can not start. 2)Press and hold the " " for three seconds; the car engine will begin to warm up for 15 minutes and the siren will sound once. After the engine start for 5 seconds,the central door will be locked, the siren would sound once. 3)After the remote start engine successfully, press and hold the " " for 3 seconds, the engine will turn off, the siren will sound once, . after 5 seconds, the central control door lock will be locked again and the siren will sound once. 2.Disarm (Unlock) 1) Press" " button once, the siren will sound twice, the central door lock will be unlocked, one push start function is on, press push button can start the car engine. 2) Pressing the" " button for 3 seconds, the siren will sound for 3 times, the trunk will be released. 3.Select 1) Press" " button once,the siren will sound once, the siren sounds function is on, repeat this operation to turn off the siren sounds function. This selection only valid on Lock and unlcok doors functions. 2)Pressing" "button for 3 seconds, the siren will sound once, PKE function will be temporarily turn off, one push start engine function turn off , press the" "

button once to turn on one push start engine function. NOTE: This function is suitable for washing or repairing the vehicle 4.Search Press" " button once, the siren will sound 15 times, easy to locate the cars. III.Functions Instruction 1.PKE inductive automatic door lock and unlock:

1) Turn off the car engine, when the car owner leaves the cars to about 2-3 meters with the remote controls, the siren will sound once, the central door lock system will be locked automatically. 2) When the car owners are close to the cars about 2-3 meters, the car siren will sound twice, the central door lock system will be unlocked, one push start engine function turn on. NOTE: The central control door lock system is only for negative trigger connection, and other connection modes need additional relays. 2, Remote start engine:

On brain unit, JP2 pin on SS-ON position, pressing LOCK button for 3 seconds , the siren will sound once, after ACC output 0.5 seconds, ON1, ON2 (Air conditioner) start outputs, the ACC, ON2 (Air conditioner) quit after 0.5 seconds, and STR start ignition 0.8 seconds, if start engine successfully, one push start indicator will be on, the car engine will be turn on after 15 minutes. 2). If the car engine can not start, the ACC, ON2 (Air conditioner) quit after 0.5 seconds, STR start ignition 12 seconds, if not start successfully, the system will continue the third start, the start time will be increased to be 17 seconds. Note I: there is a start cycle (three times) for each operation startup. If the startup is not successful after three times, it is necessary to restart the operation. 2 Note II: JP2 hand brake needle cap shall be detected when remote start engine. When JP2 hand brake needle cap in (SS-0n) position means that the hand brake is pulled and the vehicle can be started normally; JP2 hand brake needle cap in

(SS-0ff) position means that the hand brake is not pulled well and the system is not allowed to start the car; The factory default JP2 pin cap is on the (SS-ON) position. 3.Central door lock automation:

When driving, all doors are closed. Press the "unlock" or "lock" button to unlock or lock the system, but the car alarm system will not be triggered. During driving, all doors are closed. After 5 seconds, press foot brake, and the doors will be locked automatically, After parking and turning off the key, the door lock will be unlock automatically to facilitate passengers to get on and off. 4. Auto Lock :

The owner leaves the car with the remote control for about 2 to 3 meters (away from the PKE range), press unlock button to disarm the system. After 5 seconds, the siren will sound once, the central lock will be locked, the one push start button function will be off. 5.LED Indicator :

warning status: LED warning light, flash twice in one second. Disarm status: LED warning light is not on Alarm status: LED warning light flash quickly code learning status, the LED warning light is on for a long time. 6.Illegal trigger alarm In arm status, When the foot brake is illegally triggered, the system will briefly stop and alarming for 30 seconds. If it is triggered all the time, the system will automatically stop detecting the foot brake switch after 6 cycles until the foot brake switch returns to normal. 7.Emergency disarm switch:

When the remote control is lost or the car alarm system cannot be disarmed for other reasons, the owner can forcibly open the door with the key, find the emergency disarm switch, press it continuously for 10 times within 12 seconds, and the siren will sound briefly twice to temporarily remove the arm status. Press the one button start button to start the car within 2 minutes. If the one button start button is not pressed to start the car engine after 2 minutes, the siren will sound briefly after 2 minutes, The system will lock again and return to the arm status. 8. PKE remote control weak battery reminder:

When the battery is in normal state, the indicator light is blue when the remote controller works. When the battery voltage is lower than the rated value, the indicator light is red when the remote controller works. 9.Learning code:

In disarm status, long press the emergencydisarm switch for more than 3 seconds, and the LED indicator light is on for 10 seconds. The system enters the code learning mode. At the same time, press the "ARM + "DISARM" buttons of the remote control for more than 1 second, the LED indicator light flash once, and the siren sounds once, indicating that the remote control ID has been written into the brain unit memory. Press the second remote control, and the LED indicator light goes off, Indicates that the second remote control code has been learned. Maximum total of two remote controls can be learned. Note: when learning each remote control, the system will automatically increase the learning time by 10 seconds. After learning two remote controls or pressing the emergency disarm switch again, you can exit the learning status. V.One push start engine Instructions Please refer to the below steps:

1. Step on the foot brake and short press push button 1 second to start engine:

2.Step on the brake and short press for 1 second to cut off engine;

ENGINE START STOP ENGINE START STOP Preparation before installation:

Please refer to the below steps:

Before installation, you should first confirm whether the one-button start module accessories are complete, and confirm that the electrical performance of the vehicle is working properly. If there is any abnormality, please contact the service center first to ensure correct installation. Tools preparation: small awl, electrician's knife, electric pen, wire stripper, Phillips screwdriver, electrician tape, electric drill, etc. Operations: step on the foot brake and press the push button for one second. The button indicator will light up after engine start. Operations: when the engine is turned on, step on the brake and then short press the push button for 1 second to turn off the engine. After the engine is turned off, the button indicator will be off. 3.To convert between ACC ON and panel ON without stepping on the brake. 4.Long pressing to start enginein special case:

ENGINE START STOP 1 2 OFF ACC ON 3 ENGINE START STOP Picture 1 Picture 2 Picture 3 Operations: No pressing brake, short press for 1 second to turn on the ACC audio, short press again for 1 second to turn on the dash-board, short press again to turn off the system, it can be cycled operation, at this time, the button indicator would flash. Operations: Long pressing can protect the motor for 3 seconds. If the engine cannot be started at a lower temperature or the motor is in bad condition, step on the brake and long pressing the push button to start the engine, then release hands after the engine started. Instructions for One button Start System :

When the original car with steering wheel lock and anti-theft chip lock, the original car's steering wheel lock and chip lock must be released before the application. To release the steering wheel lock, a key blank inserted into the lock hole as shown in Figure 2 and turn to ON position. To Unlock the anti-theft chip, as shown in Figure 3, bind the original car remote control and the induction coil together. Original car chip coil A C C Original car chip Original car chip processing and installation Original car chip processing and installation The first step is to put out the original car chip, usually a small rectangular black body as shown in the figure The second step is to remove the induction coil at the lock of the original car. The third step is to bound the removed chip and the induction coil of the lock with tape The fourth step is to install the processed coil and chip together inside the dash-board and then stabilized. Another easy installation method is to directly paste the chip to the induction coil at the lock position Half key blank key hole Installation diagram for original steering wheel:

The first step is to insert the key into the lock and saw it off. Leave 1 cm to extend it and you can take it out at any time with pliers. Secondly is to drill a small hole next to the lock with a drill of the same size as the 4 5 6 7 FCC Caution.

(1) 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Changes or modification warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. wire diameter to facilitate the start of the button threading The next step is to remove the small iron piece on the start button and paste it on the negative head position with glue. After installation, unplug the original car's starter plug to prevent the car from consuming electricity when the key is unlocked. Another note: Another easy installation method is to directly remove the lock head as a whole. Installation instructions for vehicles that need to be started by stepping on the clutch:

1. If the clutch needs to be stepped on when the vehicle is started, then the clutch and brake must be stepped on at the same time, so the push button can start successfully. 2. For the original vehicle that need to be started by stepping on the brake or clutch, then the relay must be pretended to supply power to the brake or clutch when the remote control starts. The principle is to simulate someone stepping on the brake or clutch in the car. 8 Technical parameters:

1.Working voltage: 3V 2.Static current 17-19mA 3.PKE sensing distance: 3m 4.RF receiving distance: 70m 5.Working current: Siren: + / - 10A;

Open trunk: - 250mA; Unlocking: - 250mA; Lock: - 250mA;

ACC output: + 30A on1 total electrical output: + 30A; STR output: + 30A; On2 (air conditioning) output: + 30A. 6.PKE low frequency: 125kHz 0.3 kHz 7.RF operating frequency: 433.92mhz 0.3mhz 8.Operating temperature: - 40 C to + 85 C

FCC ID LABELING AND LOCATION FCC ID Label PKE car alarm system remote FCC ID: SY9-LT509 FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

C5266091_X10_Ed.1 Guangdong LFF Technology Co., Ltd. No.9 Yongchen North Rd, Xiaoaln industrial area, Xiaolan Town, Zhongshan, Guangdong, China Date: 2022.04.01 Subject: Request for Confidentiality FCC ID: SY9-LT509 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality No No No No No No No No In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of _180_ days from the date of the Grant of Equipment Authorization and prior to marketing. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Name: Qiuzhi Ou Date: 2022.04.01 Title: Manager Signature of applicant:

1/1

C5266091_X8_Ed.1 Letter of Authorization

<Guangdong LFF Technology Co., Ltd.>

Company: Guangdong LFF Technology Co., Ltd. Address: No.9 Yongchen North Rd, Xiaoaln industrial area, Xiaolan Town, Zhongshan, Guangdong, China Product Name: PKE car alarm system remote Model Number: LT509 FCC Identifier: SY9-LT509 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Qiuzhi Ou Date: 2022.04.01 Title: Manager Signature of applicant:

1/1