FCC ID: QV7-GC88752-11 WiFi Camera-2

User manual User manual User manual User manual Senor Senor CMOS,1/5color resolution ratio 640*480300k pixel focal length 3.6mm Lens focal diameter ratio F2.4 viewing angle 60 minimum illumination 1.0Lux@550nm video Image coding format H.264 image resolution;

VGA640x480/ QVGA320x240/QQVGA(160x120) Maximum transmission rate 25fps of image Light frequency 50Hz60HzIndoor and outdoor adaptive V-REV AWB Wireless Vertical and horizontal image flip SUPPORTING network interface;

IEEE802.11b antenna gain Working model 2.0dB AP networking protocol;

networking protocol;

TCP/IPDHCPSMPTHTTPDDNSUPNP working temperature 0 - 50C20% - 80%

storage temperature

-10C ~ 60 0% - 90%

working voltage working current 3.3V ~ 5V 200mA ~ 250mA 1 FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCCs RF exposure guidelines, place the product at least 20cm from nearby persons. The device must not be co-located or operating in conjunction with any other antenna or transmitter. 2

14+

MM 8S Cr" 7

GSC 5 4-CHANNEL PRESSURE FIXED POSITION HOVERING REMOTE CONTROL DRONE USER MANUAL MAIN FEATURES e Utilizes the 4-axis structure, enabling the drone to be even more flexible,speedy,and possessing a relatively stronger wind-withstanding capability.It can fly both in large indoor spaces and outdoors. e Built-in 6-axis gyro stabilizer to ensure accurate positioning in-flight. e The structure uses a modular design which makes it easy to install and repair. e Headless function making it easy for directional control. e Pressure-fixed-position hovering function for Auto Hover Mode. e 360 stunt flip. e High quality aerial function for getting the fun of different photography. Safety Guide

. Please store the smaller-sized drone accessories in places that are out of reach of children. This drone is very powerful. For all first-time flights, the left joystick must be slowly pushed up in order to prevent the drone from ascending too fast to avoid unnecessary collision and possible damage or injury. When the flight is ended, first turn off the power of the remote control. Then turn off the power of the drone. Avoid placing the batteries in places with high temperatures and exposure to heat. Take extra precaution to ensure that the drone is at a minimum distance of 15 feet from the pilot, other people, and animals in order to prevent bodily injury during flight operation.A minimum separation distance of 20 cm must be maintained between the user's body and the device under normal use condition. This drone is for people ages 14+. It must be flown always within the line of sight of the pilot (or instructor) and flown safely. Non-rechargeable batteries are not to be recharged;Batteries are to be inserted with the correct polarity;Different types of batteries or new and used batteries are not to be mixed. When the drone is not in use, please remove the batteries in the remote control. 9. The supply terminals are not to be short-circuited. 10.Attention: Drone assembly under adult supervision. 11.The pilot is responsible for the safe operation and safe distance from uninvolved persons and property on the ground and from other airspace users and shall never fly the drone above crowds (> 12 persons). 12.Discharge the battery to 40%-50% (On a full charge, fly for half of the total flight time) if it will not be used for 10 days or more, this can greatly extend the battery life. Repair and maintenance 1. Use dry and soft cloth to clean this product. 2. Avoid exposing this product to heat. 3. Do not immerse this product in water, otherwise, the electronic parts will be damaged. 4.Transformers used with the toy are to be regularly examined for damage to the cord,plug,enclosure and other parts,and that,in the event of such damage,the toys must be used with this transformer until the damage has been repaired. Package Description The following items can be found in this product package:

Drone Card Reader * Camera Remote Control Main Blades (Contain Memory Card) Instruction Manual Charger Wrench Screwdriver Protective Gear USER MANUAL Installation/Removal Procedures For Protective Gear Protective Gear Installation:

1. Push the protective gear into the connector on the main body as shown. Protective Gear Removal:

1. Pull up the protective gear according to the figure and at the same time pull the protective gear outwards as shown. Blade Installation/Removal Blade installation:

1. Blade is inserted as shown. 2. Use a wrench to fasten the hexagonal nut under the base of the main axis, then press blade A onto the axis. Turn the blade counterclockwise to lock it in. Blade B is locked in by turning it clockwise. Attach blade cover as shown. Remove the blade cover as shown. Use a wrench to fasten the hexagonal nut under the base of the main axis, then press blade A onto the axis. Turn the blade clockwise to loosen it. Blade B is loosened by turning it counter-clockwise. 3. Remove the blade. NOTE: Make sure to match the marking on the blade A or B with the body base marking A or B. Installation/Disassembly Steps For High-Definition Camera Installation steps for camera 1. Aim the camera at the interface and push it as left image. 2. Connect the camera cable into the socket as left image. Dismantling steps for camera 1. Pull out the camera cable from the socket as left image. 2. Press the camera locked button and pull camera out at the same time. Note: After switching on the power of the drone, do not insert or pull out the plug that connects to the drone on the high-definition camera. Battery Changing And Charging Methods For Drone 1.Press the power button on the top of the drone to make sure the drone is turned OFF. 2.Press and hold the fastening component underneath the battery and pull the battery out at the same time. Connect the plug from the charger into the port in the battery, then connect the charger into the charging cradle. The indicator light will turn on while charging and turn off when charging is complete. It takes 150 minutes to completely charge the battery. After the battery is fully charged, put the the battery back into the drone. The charging time is about 150 minutes; Hover flight time is approximately 9 minutes. Precautions as follows during charging of battery:

- Avoid placing the active batteries in places with direct exposure, sunlight and high temperatures. For example, naked light or electrical equipment installations; otherwise it may cause damages or explosions.

- Avoid immersing the batteries in the water. The batteries shall be stored in a cool and dry place.

- Avoid dismantling the batteries.

- During the charging of battery, avoid leaving the charging place.

- Rechargeable batteries are to be removed from the toy before being charged;

- Rechargeable batteries are only to be charged under adult supervision;

- Exhausted batteries are to be removed from the toy;

- Caution: Risk of explosion if battery replaced by an incorrect type dispose of used batteries according to the instructions.

Understanding Your Remote Control Remote controls button function description:

Power ON/OFF e ye Right joystick - Push in

- over 3 seconds to enter Left joystick - Keep... ke ( ; headless mode then push pushing in for 4 TGS = in again to exit. Quickly trimming. To clear / \ \ TKS \ push in and release to all the trimming | } | change high / low speed, settings, keep SS \ (one beep means low pushing in and a speed and two beeps push the power \ means high speed.) button at the same =

time. 7e 360 Stunt flip button

*..@ Push for auto take-off and landing. Battery cover 4 x AA Alkaline Batteries 1. Battery Installation Method: Open up the battery cover at the back of the remote control. Correctly place 4 x AA alkaline batteries in the battery box in strict adherence to the polarity instructions (the AA alkaline batteries are not included). 1. During the battery installation, it must be ensured that the polarities of the batteries are matched with that of the battery box. No battery shall be installed

/\ with the opposite polarity. 2. Do not use new and old batteries together. 3. Do not use different types of batteries together. 4. Do not use rechargeable batteries. Product features 1. Low-voltage Protection:

When the four indicator lights at the bottom of the drone start flashing, it means that the drone's battery power is low. At this time, the drone will initiate the height-limiting function and will descend to a safe altitude. 2. Over-current Protection:

If the drone encounters a direct impact from a foreign object,or is obstructed, or if the blades are not rotating, the drone will go into over-current protection mode. 3. Level Calibration Function:

Place the drone on a level surface and at the same time, push both left and right joysticks to the lower right corners for 2 to 3 seconds; the led light indicator on the drone will blink rapidly, and it will return back to the normal status after about 2 to 3 seconds. The level calibration is successful. 4. Fast/Slow Speed Function:

Slow speed by default when first powered-on. Possible to switch the function mode of fast/slow speed by pressing in on the right joystick for a short time. It is switched into fast soeed mode when two beep sounds come from the remote control,pressing in on the right joystick for a short time under fast soeed mode and then one beep sound would come from the remote control, then it is then switched back into slow speed mode. 5. 360 Stunt Flip Function:

When you are familiar with the basic actions, you can proceed to explore even more exciting stunt actions. Fly the drone to a height of 20 feet above the ground, push the upper right corner button

(Stunt Flip Button) on the remote control and simultaneously push the right joystick to the farthest position of Front/Back/Left/Right, the drone will now execute the Front/Back/Left/Right stunt flip action. Note: Drone will have the best stunt flip action when the batteries are fully charged. 6. Auto Hover Function:

After using the left joystick (throttle) to control the ascending / descending flight of the drone, release the left joystick (accelerator) and the drone will hover at that height when the joystick is released. 7. Headless function:

A. Defining forward direction:

2. After connecting the drone to the power supply, push the switch to ON position, and adjust the specified direction of the drones head under the headless mode as the new forward direction. Push the left joystick (throttle) on the remote control up to the farthest position and then pull down to the farthest position. When the remote control issues a long beep sound, it means the frequency and defining forward direction functions are completed. B. Calibration for the definition of the front:

1. When the drone encounters a direct impact with foreign objects in the headless mode, if there is an occurrence of deviation of the defined direction, it is only required to push both the left and right joysticks to the bottom left corners simultaneously after placing the flying direction of the drone in the correction position. When the led light indicator of the drone is in a long ON mode after slowly flashing for 3 seconds, it indicates the calibration is complete. C. Toggling between headless function and normal function:

1. After the drone is matched with the corresponding frequency, the drone would be in normal pattern by default. At this time the indicator light on the drone would be in a state of on for a long time. After pressing in on the right joystick of the remote control for 2 seconds, the remote control would make a sound of beep, beep, beep to show that it has entered into a state of headless mode.Pressing in on right joystick for 2 seconds then a long sound of beep would be heard to show an exit status.(When under the state of headless mode, four indicator lights on the drone are led lights which flicker once every four seconds)

2. Under the headless mode, the operator does not need to differentiate the head position of the drone, and only needs to control the drone's direction front/back/left/

right by using the right joystick direction on the remote control. 8. Photo/Video Instructions 1. After install the camera, turn on the drone, the camera works normally when the RED indicator changes from flashing to be green and keep lights on. If the RED indicator only flashing and lights off a few seconds later, it means the camera was not installed the memory card. 2. How to take photos and videos Take Photo:

Make sure camera is on, when push the PHOTO button, a beep from transmitter, camera take a photo with the GREEN indicator will change to RED and flash one time. Take Video:

Make sure camera is on, when push the VIDEO button, two beeps from transmitter, camera start to take video after the GREEN indicator change to RED and keep flashing. To stop and save the video, press the VIDEO button again ,than camera indicator stop flashing and keep lights on as GREEN . Flight Preparation And Switching The Drone On And Off 1. Flight Preparation Step 1: Push the power button of the remote control. Step 2: Install the battery pack in drone. Step 3: Press on the power button on the top of the drone to make sure the drone is turned ON. Step 4: Push the left joystick (accelerator) up to the highest point and then push down to the lowest point. When the led indicator lights in the drone change from quick flashing to continuous light, it means that the drone goes into the flight standby mode. Method 1: push the left joystick (accelerator) to the highest point and then back to the center, the blades of the drone start rotating slowly. Move the left and right joysticks inwards in an internal loop of 8 for 1 second, the blades of the drone start rotating slowly. When the drone is stationary,press the B button, the drone automatically takes off and hovers at a certain height. 3. Turning off the drone Method 1: Push the left joystick (Accelerator) to the lowest level and hold there for 2 to 3 seconds, the drone can then be turned off. Move the left and right joysticks inwards in an internal loop of 8 for 1 second, and the drone can be turned off. When the drone is in flight, press the B button, the drone will descend to the ground and lands. When the left joystick (Accelerator) When the right joystick (Direction is pushed upwards or downwards, Rudder) is pushed upwards or the drone will ascend or descend downwards, the drone will advance correspondingly. forward or backward correspondingly. When the left joystick (Accelerator) | When the right joystick (Direction is pushed towards the left or right, Rudder) is pushed towards the left or the drone will turn left or right right, the drone will fly sideways to the correspondingly. Trimming operation left or right correspondingly. While the drone is hovering in the air, it automatically flies forward/backwards, press in on the left joystick and at the same time push the right joystick forward/backward slightly to fine tune the direction. Dont release the left joystick until the drone is flying in a stable state. While the drone is hovering in the air and automatically flies left/right, press in on the left joystick and at the same time push the right joystick left/right slightly to fine tune the direction. Dont release the left joystick until the drone is flying in a stable state. While the drone is hovering in the air, wnen the drone automatically rotates and flies towards the left/right, press in on the left joystick and at the same time move joystick to the right or left to adjust the direction. Dont release the left joystick until the drone is flying in a stable state. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

eReorient or relocate the receiving antenna. elncrease the separation between the equipment and receiver. eConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. eConsult the dealer or an experienced radio/TV technician for help. This device complies with FCC radiation exposure limits set forth for general population (uncontrolled exposure). This device must not be collocated or operating in conjunction with any other antenna or transmitter. Decoration of Conformity Inserts:

Hereby, GuangDong Syma model aircraft Industrial co.,ltd, declares that this drone is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC A copy of the full DoC is attached AL me RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.User has the choice to give his product to a competent recycling organization or to the retailer when he buys an new electrical or electronic equipment. Accessories/Parts List Upper body Lowe body Rotor Blade Foot Stand Protective Gear Lamp Cover LED Light Bar

( Red ) oa LED Light Bar LiPo Battery Card Reader Plating Fitting

(Green ) 3 2 |

Blade cover Main stand Blade lockstitch A Blade lockstitch B Receiver Board Remote Control Product descriptions Product Name Product Name 2 S 2 S IX}

Top Main Body Cears 02 Bottom Main Body 03 Blade(Clockwise Direction) Circuti Board np

=a [oa [os a/Jajfs]sa]2 Blade(Counter Clockwise Direction) Base of dash Protective Gear LED Light Bar(green) Battery LED Light Bar(red) Motor(Clockwise Direction) Blade lockstitch A Motor(Counter-clockwlse Direction) Blade lockstitch B Foot Stand Camera Lamp Cover Blade cover NO.

Main Specifications Drons Length:50cm _ Drones Width:50cm Drones Height:19cm Motors Model: 132 Battery: 7.4V/2000mAnh lithium battery Rectification procedures

. The drone has entered into 1. Charge up the drone. lowvoltage protection. 2. Change the batteries of The drone . When the power of the remote the remote control. has no control is weak, the power light | 3. Adjust the channel of response indicator will blink. both the remote control

. The channel selection of the and drone such that remote control does not match they are in synchronized with the drones coding. mode. The power of the remote control is weak. 1. Change the batteries. 2. Change to a place where there is no interference with the same frequency. The flight response of the drone is

. There is an interference with the same frequency as that of not sensitive the remote control. 1. Re-adjust the calibration until the drone is level 1. The drone is not calibrated to the ground. For further level to the ground. details, see No.3 on Page 7 for details (Function of horizontal adjustment). The drone is flying towards its side in one direction during hovering

. Re-define the front direction. For further details, see on Page 8 for details (Headless Function). In the headless state, it is biased 1. Many collisions may cause towards the front head biasness. direction

. Re-adjust the calibration until the drone is level to the ground. For further details, see No.3 on Page 7 for details (Function of horizontal adjustment). 1. The drone is not calibrated level to the ground. Fixed high instability / up and _ . Avoid to fly under the the severe weather condition. down movement severe weather condition. 3. Violent collision resulting in 2. Unstable air pressure under

. Make horizontal adjustment again, see No.3 on Page 7 for details

(Function of horizontal adjustment). data disorder of gyroscope.

-18-

Manufacturer Guangdong Syma Model drone Industrial Co., Ltd. The Crossing of No.2 West Xingye Road and North Xingye Road,Laimei. Industrial Park Chenghai District Shantou City Guangdong China. The company has the right of final interpretation of this instruction manual statement.