FCC ID: 2AR82-SKIWB7638U2 IEEE 802.11a/b/g/n 2T2R USB Wi-Fi Module Integrated Bluetooth 2.1+EDR/4.2/5.0

Guangzhou Shikun Electronic Technology Company Limited SPECIFICATION SKI.WB7638U.1_MT7638BUB IEEE 802.11a/b/g/n 2T2R USB Wi-Fi Module Integrated Bluetooth 2.1+EDR/4.2/5.0 Approved by Shikun Checked by Rechecked by Approved by Please send the original back to us after you have approved and signed. Approved by customer Comments Approved by Companys seal Customers Name:

CVTE REVISION HISTORY VERSION DATE BOARD ID PAGE DESCRIPTION AUTHOR V0 2020.09.01 All First Issued. SKI.WB7638U.1 _MT7638BU B19104 CVTE Content 1. Introduction ......................................................1 2. FEATURES .......................................................1 3. Block Diagram ...............................................2 4. Package Outline and Mounting ..........................2 5. Pin Definition .................................................3 6. Product Pictures ..............................................4 7. Key Materials .................................................4 8. General Requirements ........................................4 9. Electrical Characteristics .....................................5 10. Mechanical,Environmental and Reliability Tests .................................... 12 11. Package .......................................................14 12. Software Requirements ....................................15 CVTE SKI.WB7638U.1_MT7638BUB 1. Introduction SKI.WB7638U.1_MT7638BUB module is based on MEDIATEK MT7638BUN solution. MT7638BUN is a highly integrated single chip which features a low power 2x2 11a/b/g/n dual-band Wi-Fi subsystem and a Bluetooth subsystem. The Wi-Fi subsystem contains the 802.11a/b/g/n radio, baseband, and MAC that are designed to meet both the low power and high throughput application.The Bluetooth subsystem contains the Bluetooth radio which complies with Bluetooth v2.1+EDR, v4.2, and v5.0, baseband, link controller. This documentation describes the engineering requirements specification. SKI.WB7638U.1_MT7638BUB MEDIATEK MT7638BUN MT7638B 2x2 11a/b/g/n Wi-Fi Wi-Fi 802.11a/b/g/n MAC 2.1+EDRv4.2 v5.0 2. FEATURES Reserving System IEEE Std. 802.11a IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n Chip Solution Band Dimensions Bluetooth 2.1+EDR/4.2/5.0 MT7638BUN 2.4/5GHz 32.0mm22.0mm3.0mm Type Protocol Frequency Remarks Mounting Method SMD SKI.WB7638U. 1_MT7638BUB IEEE 802.11a/b/g/n

+ Bluetooth 2.1+EDR/4.2/5.0 ANT Interface 2.4/5GHz IPEX 32.0mm 22.0mm3.0mm QR-ZZPJ-017A 1 CVTE 3. Block Diagram SKI.WB7638U.1_MT7638BUB 4. Package Outline and Mounting 1mm 20.2mm0.1mm QR-ZZPJ-017A 2 CVTE 5. Pin Definition SKI.WB7638U.1_MT7638BUB PIN SYMBOL DESCRIPTION WOW WIFI WAKE HOST \ WIFI 4.7Kohm 3.3V WLAN RST \ WLAN 10Kohm 3.3V 3.3V input \ 3.3V USB2.0 DM Signal \ USB2.0 USB2.0 DP Signal \ USB2.0 BT SYNC Frame sync signals from TV to sync with 3D glass via Bluetooth\3D BT_WAKE_HO Bluetooth wakeup the host\ 4.7Kohm 3.3V BT RF Output, connect to external antenna\

WL_RF1 Wi-Fi RF port1, connect to external antenna\Wi-Fi 1 Wi-Fi RF port0, connect to external antenna\Wi-Fi 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 WLAN RST VDD_3.3V USB_DM USB_DP GND ST GND BT_RF GND GND GND GND WL_RF0 GND Ground\

Ground\

Ground\

Ground\

Ground\

Ground\

Ground\

QR-ZZPJ-017A 3 CVTE 6. Product Pictures SKI.WB7638U.1_MT7638BUB top view bottom view 7. Key Materials

/IC MT7638BUN Model

Spec. 76-QFN SKI.WB7638U.1 FR-4,4LAY 2.3.3.400001535 40MHz No. 1 2 3 4 Name PCB

/Crystal

/ duplexer SLFD18-2R450G-13T

Mark

8. General Requirements No. 8-1 8-2 8-3 8-4 8-5 8-6 8-7 Feature Operation Voltage Current Consumption Ripple Operation Temperature Antenna Type Description 3.3V+/-0.3 700mA 100mV 0C to +40C External antenna USB High Speed USB 2.0 Interface Storage Temperature

-40C to +85C QR-ZZPJ-017A 4 CVTE 9. Electrical Characteristics 255 SKI.WB7638U.1_MT7638BUB 3.3V0.3V otherwise specified. The Test for electrical specification was performed under the following condition unless Ambient condition Temperature :25 5;

Power supply voltages3.3V (0.3V) input power at the Module. QR-ZZPJ-017A 5 CVTE 10. Mechanical,Environmental and Reliability Tests SKI.WB7638U.1_MT7638BUB Test Items Test Conditions Qty Criteria Condition 10-4 10-1 Drop test Face Side: 800/600/450mm 1xBox box will not been broken by appearance Edge line: 600/450/350mm visual inspection. After drop test, the outer box and inner 10-2 Vibration 5 times vibrations, then test frequency Changing from 10-3 Impact test 50m/sec2;

The packed samples within 100Kg can be tested Drop height:

Drop time: 1 each Face and edge. X-Y-Z direction, first Frequency changing from 10Hz to 30Hz to 10Hz,amplitude 0.75mm, 30Hz to 55 Hz to 30 Hz, amplitude 0.15mm, 5 time vibration. Impact acceleration:

Impact duration: 16ms Impact times: 1000. After test, the Appearance, Power EVM 3 and Frequency error shall be satisfied with the specification. After test, the Appearance, Power EVM 3 and Frequency error shall be satisfied with the specification. 1.After soldering, the soldered area must be covered by a smooth bright solder layer, some deficiencies such as a small amount of the pinhole, not wetting are 3 allowed, but the deficiencies can not be in the same place 2.At least 90% of soldered area shall be covered continuously by the soldering material. Soldering temperature:

Soldering 2355 ability test Soldering duration:

20.5S QR-ZZPJ-017A 6 CVTE 10-5 Humidity Leave samples in 403, test 93% RH @ 96 hours Thermostat cabinet temperature:

555 Applied voltage:

High 10-6 temperature load life test 110% rated voltage Working duration: 200 hour (Supply Voltage Cycle 23h power on, 1h power off) 10-7 High temperature load test Temperature: 555 Samples work for 16 hours Leave the samples in

-253@24 hours 10-8 temperature storage test Low Low 10-9 temperature load test Leave samples in -153@ 2 hours, samples function shall be normal, the let samples work for 1 hour One cycle duration 10-1 Temperature

-103@3H 403 0 circle test

@3H 10-1 Continuous 1 TP test 10-1 2 Total cycle: 10x Twice cycle duration

-103@4H

+603@4H,

+25@2H@2H Discharge voltage: 1kV C: 150pF Positive10 times 1 time for each second SKI.WB7638U.1_MT7638BUB Leave samples in standard test condition for 2 hours then test, the Appearance, 3 Power, EVM and Frequency error functional parameter shall be satisfied with the test specification. After test, leave samples in standard 60 condition for 1 hour and test, Power, EVM and Frequency error shall be satisfied with the test specification. After test, the Appearance, Power, EVM 3 and Frequency error shall be Satisfied 3 3 with the test specification. Leave samples in standard test condition for 2 hours then test, the Appearance, Power, EVM and Frequency error shall be satisfied with the test specification. After test, leave the samples in standard condition and tested the Appearance, Power, EVM and Frequency error shall be satisfied with the test specification. After test, leave the samples in standard condition and tested Power EVM and 3 Frequency error shall be qualified and all the characters shall be satisfied with the test specification. During test, There will not been appeared 3 signal disconnection or interruption between DUT and AP. ESD Discharge resistance330 3 after ESD test. The products can recoverable smoothly QR-ZZPJ-017A 7 CVTE 11. Package 1 SKI.WB7638U.1_MT7638BUB 2 3 3 QR-ZZPJ-017A 8 CVTE SKI.WB7638U.1_MT7638BUB 550pcs/*8 /=4400pcs/

4 /Label 12. Software Requirements The driver supports the following operating systems: Microsoft Windows XP, Vista and Win7. Windows XPVista win7 QR-ZZPJ-017A 9 CVTE FCC Statement SKI.WB7638U.1_MT7638BUB This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. If power exceeds the limit and the distanceOver 20cm distance in actual use between the device and user is compliant with the requirement FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. The device must be professionally installed The intended use is generally not for the general public.It is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. the user has no access to the connector. Installation must be controlled. Installation requires special training This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 Subpart C

(15.247,DSS, DTS) and Subpart E (UNII) has been investigated. It is applicable to the modular transmitter. This radio transmitter 2AR82-SKIWB7638U2 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. QR-ZZPJ-017A 10 CVTE SKI.WB7638U.1_MT7638BUB BT/BLE Anntenna 2.4 G wifi antenna PIFA PIFA 5 G wifi antenna Antenna Antenna Type Maximum Antenna Gain Frequency

(MHz) 2412 ~ 2462 2422 ~ 2452 0 1

(dBi) 1.5 1.5 QR-ZZPJ-017A 12 CVTE Canada Statement SKI.WB7638U.1_MT7638BUB This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. L'metteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR d'Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

1) L'appareil ne doit pas produire de brouillage;

2) L'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC: 24728-SKIWB7638U2 any similar wording that expresses the same meaning may be used. l'appareil hte doit porter une tiquette donnant le numro de certification du module d'Industrie Canada, prcd des mots Contient un module d'mission , du mot IC:

24728-SKIWB7638U2 ou d'une formulation similaire exprimant le mme sens, comme suit The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 etla conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformit de rf. QR-ZZPJ-017A 12 CVTE SKI.WB7638U.1_MT7638BUB This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet metteur ne doit pas tre Co-plac ou ne fonctionnant en mme temps qu'aucune autre antenne oumetteur. Cet quipement devrait tre install et actionn avec une distance minimum de 20 centimtres entre le radiateur et votre corps. This radio transmitter 24728-SKIWB7638U2 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le prsent metteur radio 24728-SKIWB7638U2 a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. The concrete contents to check are the following three points.

) Must use a PIFA antenna such as V436 with gain not exceeding 1.5 dBi

) Should be installed so that the end user cannot modify the antenna;

)Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. Le contenu concret vrifier sont les trois points suivants.

) doit utiliser une antenne comme V436 avec pifa gain n'excdant pas 1.5 dbi

) doivent tre installs de faon que l'utilisateur final ne peut pas modifier l'antenne

) La ligne dalimentation doit tre conue en 50ohm Le rglage prcis de la perte de rendement, etc. peut tre effectu en utilisant un rseau correspondant. BT/BLE Anntenna QR-ZZPJ-017A 16 CVTE 2.4 G wifi antenna SKI.WB7638U.1_MT7638BUB Maximum Antenna Gain Antenna Antenna Type Frequency

(MHz) 2412 ~ 2462 2422 ~ 2452 0 1 PIFA PIFA 5 G wifi antenna

(dBi) 1.5 1.5 Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual. (FCC/Canada Statement)". Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AR82-SKIWB7638U2IC:

24728-SKIWB7638U2 The devices must be installed and used in strict accordance with the manufacturers instruction as described in the user documentation that comes with the product. Any company of the host device which install this modular with limit modular approval should perform the test of radiated & conducted emission and spurious emission,etc. according to FCC part 15C : 15.247 and 15.209 & 15.207 ,15B Class B and 15.407 Subpart E requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209 & 15.207 ,15B Class B and 15.407 Subpart E requirementthen the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247 and 15.407) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. QR-ZZPJ-017A 16 CVTE SKI.WB7638U.1_MT7638BUB l'hte doit utiliser l'instrument uniquement dans des dispositifs qui rpondent la fcc /

(catgorie d'exposition rf mobile, ce qui signifie le dispositif est install et utilis une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen dclarations de conformit relatives l'metteur que de montrer dans ce manuel. le fabricant est responsable de la conformit de l'hte, le systme d'accueil avec le module install avec toutes les autres exigences applicables du systme comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommand de confirmer la conformit avec les exigences de la fcc / (metteur lorsque le module est install dans l'hte. le dispositif d'accueil doivent avoir une tiquette indiquant contient FCC ID:

2AR82-SKIWB7638U2IC: 24728-SKIWB7638U2 Installation Guidance The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. QR-ZZPJ-017A 16 CVTE SKI.WB7638U.1_MT7638BUB The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. This module is a limit modules. host manufacturer should confirm with module manufacturer for the installation method in end system. The external circuit should be installed in the host and connect to BT_RFIO. Antenna trace circuitry Host RF1-0 ohm CF1=CF2=NC CNF1 is IPEX connector for BT antenna. The antenna trace circuitry that will be on the host board up to the antenna port QR-ZZPJ-017A 16 CVTE

< External layout and trace information >

Trace typeRF microstrip line Trace material: Epoxy glass cloth laminate FR-4 Trace Width=22mil SKI.WB7638U.1_MT7638BUB Length1=56.586mil Length2=359.787mil QR-ZZPJ-017A 16 CVTE SKI.WB7638U.1_MT7638BUB Distance Length3=137.484mil Length5=54.465mil QR-ZZPJ-017A 16 CVTE SKI.WB7638U.1_MT7638BUB Length6=52.596mil Thickness=1.4mil RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. Class II permissive change is required on the module grant to register the additional host as a specific host also approved with the module. QR-ZZPJ-017A 16 CVTE SKI.WB7638U.1_MT7638BUB The device for operation in the band 5150-5350 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems Les dispositifs fonctionnant dans la bande 5150-5350 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux QR-ZZPJ-017A 16 CVTE

SKI. WB7638U. 1_NT7638BUB WAC: xxxxxxxxxxxx IC: 24728-SKIVE763802 FCC ID:2AR82-SKIWB7638U2 Guangzhou Shilun Electronics Co.,Ltd le:

$i0.WB7638U.1 MT76388UB MAC: 2C641F844A51 1C:24728-SKIWB7638U2 FCC ID:2AR82-SKIWB7633U2 Guangzhou Shikun Electrenics Co.

Guangzhou Shikun Electronics Co., Ltd Date: 01/06/2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program:

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints:

c) make claims regarding certification only in respect of the scope for which certification has been granted:

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized:

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested:

J) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Big my Company Name: Guangzhou Shikun Electronics Co., Ltd Contact Name: Bing Yi Title of Person: Certification Manager Address: NO.6 Liankun Road,Huangpu District Guangzhou 510530 China

Guangzhou Shikun Electronics Co., Ltd Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:Request for Confidentiality FCC ID: 2AR82-SKIWB7638U2 To Whom It May Concern:

Schematic Diagram Block Diagram Theory of Operation BOM list Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: Guangzhou Shikun Electronics Co., Ltd Contact Name: Bing Yi Title of Person: Certification Manager Address: NO.6 Liankun Road,Huangpu District Guangzhou 510530 China Date:2021/1/12

The module transmitter will be a limited module Modular Approval Request FCC (Per 15.212) FCC ID: 2AR82-SKIWB7638U2 Items to be covered 1. The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-

modulation. 3. The modular transmitter must have its own power supply regulation. 4. The modular transmitter must comply with the antenna and transmission system requirements of 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available

(see 15.31(i)). 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID:

XYZMODEL1. Any similar wording that expresses the same meaning Answer From Applicant Yes Yes Yes Yes No The modular transmitter is not stand-

alone, BT antenna connector and related matching circuit are located in the host circuit board. Yes may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. Yes 7. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. 8. Radio frequency devices operating under the provisions of this part are subject to the radio frequency radiation exposure requirements specified in 1.1307(b), 1.1310, 2.1091, and 2.1093 of this chapter, as appropriate. Applications for equipment authorization of modular transmitters under this section must contain a statement confirming compliance with these requirements. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Technical information showing the basis for this statement must be submitted to the Commission upon request. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a Limited Modular Approval

(LMA). Yes ___________________________ Bing Yi Title: Certification Manager Guangzhou Shikun Electronics Co., Ltd