FCC ID: ZKJ-CBA-L80 Android Board for GEA Wall Oven

Regulatory Module Integration Instructions This Wi-Fi/Bluetooth module Oven has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC / IC (Industry Canada) certification if they meet the following conditions. Otherwise, additional FCC / IC approvals must be obtained. The host product with the module installed must be evaluated for simultaneous transmission requirements. The users manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC / IC RF exposure guidelines. To comply with FCC / IC regulations limiting both maximum RF output power and human exposure to RF radiation, use this module only with the included onboard antenna. A label must be affixed to the outside of the host product with the following statements:

Product Name: Android Board for GEA Wall Oven Contains FCCID: ZKJ-CBA-L80 Contains IC: 10229A-CBAL80 The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. Device Classifications Since host devices vary widely with design features and configurations module integrators shall follow the guidelines below regarding device classification and simultaneous transmission, and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned testing activities. The module integrator must determine the minimum distance required between their host device and the users body. The FCC provides device classification definitions to assist in making the correct determination. Note that these classifications are guidelines only; strict adherence to a device classification may not satisfy the regulatory requirement as near-body device design details may vary widely. Your preferred test lab will be able to assist in determining the appropriate device category for your host product and if a KDB or PBA must be submitted to the FCC. Note, the module you are using has been granted modular approval for mobile applications. Portable applications may require further RF exposure (SAR) evaluations. It is also likely that the host / module combination will need to undergo testing for FCC Part 15 regardless of the device classification. Your preferred test lab will be able to assist in determining the exact tests which are required on the host / module combination. FCC Definitions Portable: (2.1093) A portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is / are within 20 centimeters of the body of the user. Mobile: (2.1091) (b) A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons. Per 2.1091d(d)(4) In some cases (for example, modular or desktop transmitters), the potential conditions of use of a device may not allow easy classification of that device as either Mobile or Portable. In these cases, applicants are responsible for determining minimum distances for compliance for the intended use and installation of the device based on evaluation of either specific absorption rate (SAR), field strength, or power density, whichever is most appropriate. Simultaneous Transmission Evaluation This module has not been evaluated or approved for simultaneous transmission as it is impossible to determine the exact multi-transmission scenario that a host manufacturer may choose. Any simultaneous transmission condition established through module integration into a host product must be evaluated per the requirements in KDB447498D01(8) and KDB616217D01,D03 (for laptop, notebook, netbook, and tablet applications). These requirements include, but are not limited to:

Transmitters and modules certified for mobile or portable exposure conditions can be incorporated in mobile host devices without further testing or certification when:

The closest separation among all simultaneous transmitting antennas is >20 cm, Antenna separation distance and MPE compliance requirements for ALL simultaneous transmitting antennas have been specified in the application filing of at least one of the certified transmitters within the host device. In addition, when transmitters certified for portable use are incorporated in a mobile host device, the antenna(s) must be >5 cm from all other simultaneous transmitting antennas. All antennas in the final product must be at least 20 cm from users and nearby persons. Or OEM Instruction Manual Content Consistent with 2.909(a), the following text must be included within the users manual or operator instruction guide for the final commercial product (OEM-specific content is displayed in italics.) Operating Requirements and Conditions:

The design of (Product Name) complies with U.S. Federal Communications Commission (FCC) guidelines respecting safety levels of radio frequency (RF) exposure for Mobile devices. Note: In the case where the Host / Module combination has been re-certified the FCCID shall appear in the product manual as follows:

FCCID: (Include Standalone FCC ID) Mobile Device RF Exposure Statement (If Applicable):

RF Exposure - This device is only authorized for use in a mobile application. At least 20 cm of separation distance between the transmitting antenna device and the user's body must be maintained at all times. Caution Statement for Modifications:

CAUTION: Any changes or modifications not expressly approved by GE Appliance could void the users authority to operate the equipment. FCC Part 15 Statement (Only Include if FCC Part 15 is Required on the End Product):

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. (OEM must follow Part 15 guidelines (15.105 and 15.19) to determine additional statements required in this section for their device class) Note 2 : This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. a. That module is limited to OEM installation ONLY. b. That OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module. c. That module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). d. That separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. e. That grantee shall provide guidance to the host manufacturer for compliance with Part 15 subpart B requirements. This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Information Le prsent appareil est conforme aux CNR dIndustrie Canada applicable aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de la FCC lignes directrices dexposition et dexposition aux frequencies radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation du dbit dabsorption spcifique (DAS).

*The operation method of the module will be written in the manual of End product as follows.

CTK Co., Ltd.

(Ho-dong), 113, Yejik-ro, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea Tel: +82-31-339-9970 Fax: +82-31-624-9501 www.e-ctk.com Label Photographs and Location CTK Co., Ltd.

(Ho-dong), 113, Yejik-ro, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea Tel: +82-31-339-9970 Fax: +82-31-624-9501 www.e-ctk.com

CTK Co., Ltd.

(Ho-dong), 113, Yejik-ro, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea Tel: +82-31-339-9970 Fax: +82-31-624-9501 www.e-ctk.com Label Photographs and Location CTK Co., Ltd.

(Ho-dong), 113, Yejik-ro, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea Tel: +82-31-339-9970 Fax: +82-31-624-9501 www.e-ctk.com

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 19, 2024 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: ZKJ-CBA-L80 Haier US Appliance Solutions, Inc. certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information:

FRN: 0025028994 Name: Haier US Appliance Solutions, Inc. Address: Appliance Park AP5-2N-65, Louisville, KY 40225, United States Contact Person: Jeff Drake Tel.: +1-502-452-5135 Email: jeff.drake@geappliances.com Sincerely, Haier US Appliance Solutions, Inc. Jeff Drake Rev 1/26/2023

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 19, 2024 FCC ID: ZKJ-CBA-L80 47 CFR section 2.911(d)(5)(i) Attestation Statement Haier US Appliance Solutions, Inc. certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: -

47 CFR section 2.911(d)(5)(ii) Attestation Statement Haier US Appliance Solutions, Inc. (the applicant) certifies that, as of the date of the filing of this application, the applicant - is / - is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, NAME: Jeff Drake TITLE: Director, Engineering Kitchen Hub Applicant: Haier US Appliance Solutions, Inc. 1 - The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters should be placed on appropriate letterhead. Rev 1/26/2023

Appliance Park, AP2-226, Louisville, KY 40225, United States Tel No : +1-502-452-5135 Fax No : +1-502-452-0784 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID: ZKJ-CBA-L80 Applicant: Haier US Appliance Solutions, Inc. Dear Examiner, This is to request a Class II Permissive change for FCC ID: ZKJ-CBA-L80 originally granted on 07/19/2022. There are some minor changes to improve power stability, and there is no change in the operating voltage level. 1) Changed PCB stack-up to reinforce power for MPU and DDR memory. 2) Modified Artwork related to the power for MPU and DDR memory. Except for the mentioned changes, has identical PCB layout, antenna, SW implementation for Wi-Fi/BT. Especially, the same Wi-Fi/BT module is also used for the new version HW. Except for the mentioned changes, the device remains electrically, Software Configuration and mechanically identical to the originally certified device and no changes have been made. Sincerely, NAME: Park Hansung TITLE: Hardware RF Engineer Applicant: Haier Korea R&D Co., Ltd.

Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID : ZKJ-CBA-L80 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Schematics Schematics_PCB Layout Parts List File Name Block Diagram.pdf Schematics.pdf Schematics_PCB Layout.pdf Part List.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, NAME: Park, Hansung Applicant: Haier Korea R&D Co., Ltd. Rev 11/20/07

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date : March 19, 2024 SUBJECT: FCC Application for (FCC ID : ZKJ-CBA-L80) To Whom It May Concern:

We, the undersigned, hereby authorize Kim Ji-Hye at CTK Co., Ltd. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by CTK on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, NAME: Park, Hansung Applicant: Haier Korea R&D Co., Ltd.

Appliance Park AP5-2N-65, Louisville, KY 40225, United States Tel No : +1-502-452-5135 Fax No : +1-502-452-0784 Special Power of Attorney I, Jeff Drake of Haier US Appliance Solutions, Inc. hereby authorize appoint Park Hansung of Haier Korea R&D Co., Ltd. to represent me to act on my behalf to do any and all of the following:

Sign on my behalf the agency, anti-drug and confidentiality cover letters and apply to FCC for the products. The right, powers, and authority in fact to exercise any and all of the rights and powers herein granted shell commence and be in full force from 2024/01/04 and continue to effective unless specifically terminated by either party. Applicant: Haier US Appliance Solutions, Inc. FCC ID: ZKJ-CBA-L80 Dated March 19, 2024 Sincerely, NAME: Jeff Drake TITLE: Director, Engineering Kitchen Hub Applicant: Haier US Appliance Solutions, Inc. Address: Appliance Park AP5-2N-65, Louisville, KY 40225, United States

Appliance Park AP5-2N-65, Louisville, KY 40225, United States Tel No : +1-502-452-5135 Fax No : +1-502-452-0784 MODULAR APPROVAL LETTER Applicant : Haier US Appliance Solutions, Inc. FCC ID : ZKJ-CBA-L80 Date : 2022/05/18 We would like to answer for Single Modular Approval in accordance with the requirement of rule part 15.212 as described below No. Requirements Comment Comply (Y/N) 1 2 3 4 5 6 7 8 The radio element of the modular transmitter has its own shielding The modular transmitter must have buffered modulation data/inputs (if such inputs are provided) The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). Refer to the external photo All input to the modules are buffered through microprocessor inputs. Internal power regulators Refer to the Block-diagram Refer to the internal photo The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. The EUT was tested in a standalone configuration via a SD extension cable Refer to the test setup photo The modular transmitter must be labeled with its own FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements The modular transmitter must comply with any applicable RF exposure requirements Refer to the user manual Refer to the user manual Refer to the RF exposure statement for more details. Y Y Y Y Y Y Y Y Sincerely, NAME: Park, Hansung Applicant: Haier Korea R&D Co., Ltd.

Appliance Park AP5-2N-65, Louisville, KY 40225, United States Tel No : +1-502-452-5135 Fax No : +1-502-452-0784 FCC DFS Uniform Spreading Declaration Date: 2022-05-18 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. FCC ID: ZKJ-CBA-L80 Product/ Model Number : Android Board for GEA Wall Oven / CBA-L80 Regarding Uniform Spreading requirements for DFS operation identified in FCC 06-96 in ET Docket 03-

122;

"Uniform Channel Spreading: The spreading of U-NII device Operating Channels over the 5250-

5350 MHz and/or 5470-5725 MHz bands to avoid dense clusters of devices operating on the same Channel."

We declare the device provides on aggregate a Uniform Spreading of the Operating Channels across the entire band. This applies to the 5250-5350 MHz and/or 5470-5725 MHz bands. NAME: Park, Hansung Applicant: Haier Korea R&D Co., Ltd.

Appliance Park AP5-2N-65, Louisville, KY 40225, United States Tel No : +1-502-452-5135 Fax No : +1-502-452-0784 Special Power of Attorney I, Jeff Drake Haier US Appliance Solutions, Inc. hereby authorize appoint Park Hansung of Haier Korea R&D Co., Ltd. to represent me to act on my behalf to do any and all of the following:

Sign on my behalf the agency, anti-drug and confidentiality cover letters and apply to FCC for the products. The right, powers, and authority in fact to exercise any and all of the rights and powers herein granted shell commence and be in full force from 2022/05/18 and continue to effective unless specifically terminated by either party. Applicant: Haier US Appliance Solutions, Inc. FCC ID: ZKJ-CBA-L80 Dated 2022/05/18 Sincerely, NAME: Jeff Drake TITLE: Director, Engineering Kitchen Hub Applicant: Haier US Appliance Solutions, Inc. Address: Appliance Park AP5-2N-65, Louisville, KY 40225, United States

Appliance Park AP5-2N-65, Louisville, KY 40225, United States Tel No : +1-502-452-5135 Fax No : +1-502-452-0784 FCC Software Configuration Control Declaration Date: 2022-05-18 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. FCC ID: ZKJ-CBA-L80 Product/ Model Number : Android Board for GEA Wall Oven / CBA-L80 Regarding FCC Country Code Selection guidelines identified in KDB 594280 "Country Code Selection". All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. NAME: Park, Hansung Applicant: Haier Korea R&D Co., Ltd.

Appliance Park AP5-2N-65, Louisville, KY 40225, United States Tel No : +1-502-452-5135 Fax No : +1-502-452-0784 Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 UNII Device Declaration Letter To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC ID: ZKJ-CBA-L80

(1) Operational Mode :

Master N/A Client with Radar detection capability Client without radar detection capability, Active Scanning

(the device can transmit a probe

(beacon)) passive scanning

(where the device is can listen only with no probes) Ad Hoc Mode capability Access point capability Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band (MHz) 2412-2462 2422-2452 5180-5240 5190-5230 5210 5745-5825 5755-5795 5775 Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No No No

(3) Country code selection ability If yes, pls explain how it was implemented:

(4) Meet 15.202 requirement pls check below :

A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-

DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer.

(If apply, pls help to provide explanation on it was implement, and how software was controlled) Does not apply Apply Sincerely NAME: Park, Hansung Applicant: Haier Korea R&D Co., Ltd.