Camera Camera 127.3 mm 23.5 mm IR Light IR Light 1 Appearance Touch Screen m m 1
. 2 3 2 2 Installation Installaon Environment:
Avoid backlight, direct sunlight, and indirect sunlight. For beer recognion, there should be light source in or near the installaon environment. If you have to install the device outdoors, you should install a protecve shield(oponal) for the device. 1 Remove the back sheet under the TAMPER buon by removing the 2 screws. Secure the mounng plate on the base plate with 4 screws. Remove the sponge tage on the base plate and secure the device on the mounng plate with 2 screws. Backlight Direct Sunlight Direct Sunlight through Window Indirect Sunlight through Window Close to Light a 3 Dig a hole (242 mm 114 mm 30.5 mm) on the wall. Place a gang box in the hole (a), and remove the 4 mounng ears with tool (b). Secure the combinaon and the gang box with 1 screw (c). Loudspeaker Mounng Plate DS-K1T680 Series Face Recognition Terminal Quick Start Guide Card Reader UD21052B Network Interface microSIM Card Slot Fingerprint Module TAMPER Wiring Terminal Base Plate b 2 Secure the decoraon plate on the base plate with 4 screws. Sck 3 waterproof membranes on the decoraon plate as shown below. Route the cable through the cable hole of the plates, and connect to external devices cables. microUSB Debugging Port
(For debugging using only) Wall c b b b b a The gang box is oponal. You should purchase it separately. The waterproof membranes is used only in the ush mounng. For surface mounng, see the user manual. 3 Wiring (Normal) The pictures here are for reference only. Decoraon Plate Rear Side 2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instrucons for using and managing the Product. Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon contained in the Manual is subject to change, without noce, due to rmware updates or other reasons. Please nd the latest version of this Manual at the Hikvision website
(hps://www.hikvision.com/). Please use this Manual with the guidance and assistance of professionals trained in supporng the Product. Trademarks and other Hikvision's trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and logos menoned are the properes of their respecve owners. Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED AS IS AND WITH ALL FAULTS AND ERRORS. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protecon During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognion features, biometrics data is stored in your device with encrypon method; for ngerprint device, only ngerprint template will be saved, which is impossible to reconstruct a ngerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protecon laws and regulaons, including without limitaon, conducng security controls to safeguard personal data, such as, implemenng reasonable administrave and physical security controls, conduct periodic reviews and assessments of the eecveness of your security controls. Scan the QR code to get the user manual for detailed informaon. Use only power supplies listed in the user instrucons:
Model Manufacture Standard ADS-26FSG-12 12024EPG Shenzhen Honor Electronic Co.,Ltd MSA-C2000IC12.0-24P-DE MOSO Technology Co.,Ltd ADS-26FSG-12 12024EPB Shenzhen Honor Electronic Co.,Ltd ADS-26FSG-12 12024EPCU/EPC Shenzhen Honor Electronic Co.,Ltd ADS-26FSG-12 12024EPI-01 Shenzhen Honor Electronic Co.,Ltd ADS-26FSG-12 12024EPBR Shenzhen Honor Electronic Co.,Ltd PG PDE PB PCU PI PBR Power Input Alarm Input Alarm Output RS-485 Wiegand Door Lock Network Interface
+12 V~24 VDC Red Black Group A IN1 GND IN2 NC COM NO Group B GND GND Group C GND BTN GND Group D Yellow/Blue Black Yellow/Orange Yellow/Purple Yellow/Brown Yellow/Red Yellow Blue Black Green White Black White/Purple White/Yellow White/Red Yellow/Green Black Yellow/Grey Yellow/Black B1 B2 B3 B4 B5 B6 C1 C2 C3 C4 C5 C6 D1 D2 D3 D4 D5 D6 D7 Alarm Input Device Power Supply
(NC)
(NO) Alarm Output Device Alarm Output Device 12V Power Supply Wiegand Card Reader Electric Dropbolt
(NC)
(COM)
(NO) Power Supply NO COM NC Exit Button NO COM NC When connecng door contact and exit buon, the device and the RS-485 card reader should use the same common ground connecon. The Wiegand terminal here is a Wiegand input terminal. You should set the devices Wiegand direcon to input. If you should connect to an access controller, you should set the Wiegand direcon to Output. For details, see the user manual. The suggested external power supply for door lock is 12 V, 1 A. The suggested external power supply for Wiegand card reader is 12 V, 1 A. For wiring the re system, see the user manul. Do not wire the device to the electric supply directly. If the device support PoE, the network interface supports power supply by PoE. If the device supports power supply by PoE and the network interface is connected, do not wire the power input terminal. Electric Strike Door Contact 3.2 Wiring (With Secure Door Control Unit) Face Recognition Terminal Secure Door Control Unit Power Input Sensor Input RS-485 B1 B2 B3 Yellow Blue Black Secure Door Control Unit Wiring Terminal Exit Button SENSOR Green/Brown Black NO COM NC BUTTON Green/Black Black Door Contact Exit Button Lock Output NC COM White/Purple White/Black White/Red
(COM) Red Black B1 B2 B3 B4 C1 C2 C3 NO COM NC
(NC) Power
(NO) Electric Dropbolt Electric Strike The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12 V, 0.5 A. 4 Quick Operation Acvaon Power on and wire the network cable aer installaon. you should acvate the device before the rst login. If the device is not acvated yet, it will enter the Acvate Device page aer powering on. Steps:
1. Create a password and conrm the password. 2. Tap Acvate to acvate the device. For other acvaon methods, see the device user manual. We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case leers, lower case leers, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can beer protect your product. Set Applicaon Mode Aer acvaon, you should select an applicaon mode. Select Indoor or Others from the drop-down list and tap OK. If you install the device indoors near the window or the face recognion funcon is note working well, select Others. Set Language Select a language from the drop-down list. Set Network Parameters Wired Network:
-If enable DHCP, the system will assign the IP address and other parameters automacally.
-If disable DHCP, you should manually set the IP address and other parameters. Wi-Fi:
-Select a Wi-Fi and enter the Wi-Fis password.
-Or tap Add Wi-Fi and enter the Wi-Fis name and password. If you select Wired Network, make sure the device has connected to a network. Link to Mobile Client Download and install the mobile client. Use the scan QR code funcon of the mobile client and scan the QR code on the device to link the device to the mobile client. Set Administrator Steps:
1. Enter the administrators name and tap Next. 2. Select a credenal to add. You can select face, ngerprint, or card. 3. Tap OK. 5 Add Face Picture 1. Use nger to hold the screen surface for 3 s and slide to right/le and enter the acvaon password to enter the Home page. 2. Enter the User Management page, tap + to enter the Add User page. 3. Set the user parameters according to actual needs. Only the device with the ngerprint module support the ngerprint related funcons. 4. Tap Face and add the face informaon according to the instrucons. You can view the captured picture on the screen, Make sure the face picture is in good quality and size. For details about the ps and posions when collecng or comparing the face picture, see the contents on the right. 5. If the picture is in good condion, tap the . Or tap the to take another face picture. 6. Tap the save icon to save the sengs. Go back to the inial page to start authencaon. For other authencaon methods, see the device user manual. User other authencaon methods if the device is aected by the light or other items. 1:N Matching: The device will compare the captured face picture with the ones in the database. 1:1 Matching: The device will compare the captured face picture with the user linked face picture. Biometric recognion products are not 100%
applicable to an-spoong environments. If you require a higher security level, use mulple authencaon modes. Tips When Collecng/Comparing Face Picture Posions When Collecng/Comparing Face Picture Expression Keep your expression naturally when collecng or comparing face pictures, just like the expression in the picture on the right. Do not wear hat, sunglasses, or other accessories that can aect the facial recognion funcon. Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed. Recommended Height:
1.43 m to 1.90 m Too High Too Low Posture 1.4 m 1.4 m In order to get a good quality and accurate face picture, posion your face looking at the camera when collecng or comparing face picture. Correct Tilt Side Raise Bow Size Make sure your face is in the middle of the collecng window. Correct Too Close Too Far 1.4 m 1.4 m 0.5 m 0.5 m Too Close Too Far 0.5 m 1.2 m Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info Warning In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. CAUTION: To reduce the risk of fire, replace only with the same type and rating of fuse. CAUTION: This equipment is for use only with Hikvisions bracket. Use with other (carts, stands, or carriers) may result in instability causing injury. To prevent possible hearing damage, do not listen at high volume levels for long periods. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) 4 the fingerprint sensor metal
. Wait one-half hour after switching off before Caution
+ identifies the positive terminal(s) of equipment which is used with, or generates direct current. + identifies the negative terminal(s) of equipment which is used with, or generates direct current. No naked flame sources, such as lighted candles, should be placed on the equipment. The USB port of the equipment is used for connecting to a USB flash drive only. The serial port of the equipment is used for debugging only. Burned fingers when handling handling the parts. Install the equipment according to the instructions in this manual. To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation instructions. Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden
(ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. Please make sure that the biometric recognition accuracy will be affected by the collected pictures' quality and the light in the environment, which cannot be 100% correct.