HSDWAM83 user manual 1. Product Description HSDWAM83 Hansong own module which is base on the Microchip DWAM83 module with its own PCB antenna or the module external antenna. It is an uncompressed wireless digital audio transceiver operation in the 2.4GHz, 5.2GHz and 5.8GHz bands. The wireless audio link supports up to 4 stereo audio streams and comes together with additional features such as: data encryption, Automatic Frequency Allocation and support Kleernet. The Basic Features High Quality Audio Networking and Connectivity Power Management Integrated 8052MCU Digital Audio Clock Synchronization Sample Rate Converter(SRC)+ Sample Rate Detector Kleenet 2. Product parameter 2.1 Module Specifications 2.1 Absolute Maximum Rating 2.2 Recommended Operating Conditions 2.3 module Block Diagram 2.4 Power Consumption 2.5 RF performance 3. Product antenna The module uses embedded PCB track Tri-Band antennas. Or you can use the module with external PCB antenna or the coaxial antenna with reverse-SMA male connector. Antenna Type: module embedded PCB track antenna, module external PCB antenna(PIFI), module external mono antenna with reverse-SMA connector Antenna Gain: module own PCB antenna, 2.4G: 1.5dBi; 5G: 1.5 dBi External PCB antenna (PIFI), 2.4G: 4.2 dBi; 5G: 4.5dBi External mono antenna with reverse-SMA male connector: 2.4G: 3.6dBi;
5G: 3.8 dBi Modulation: QPSK; data rate: 100Kbps 4. Product picture 4.1 module embedded antenna Top view: Bottom view 4.2 module without embedded antenna Top view: Bottom view 5. Caution:
This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente
(p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Only for detachable antennas:
This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Gain of antenna: 2.4GHz: 4.2 dBi max; 5GHz: 4. 5 dBi max. Type of antenna: Omni-directional, PCB antenna (PIFI) Impedance of antenna: 50ohm OR, Gain of antenna: 2.4GHz: 3.6 dBi max; 5GHz: 3.8 dBi max. Type of antenna: Omni-directional, mono antenna Impedance of antenna: 50ohm Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle s'il fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Gain d'antenne: 2.4GHz 4.2dBi maximal; 5GHz 4. 5 dBi maxial Type d'antenne: 50 ohm, Omni-directionnel, PIFI OR, Gain d'antenne: 2.4GHz 3.6 dBi maximal; 5GHz 3.8 dBi maxial Type d'antenne: 50 ohm, Omni-directionnel, mono MPE Reminding To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installes doivent tre situes de facon ce que la population ne puisse y tre expose une distance de moin de 20 cm. Installer les antennes de facon ce que le personnel ne puisse approcher 20 cm ou moins de la position centrale de l antenne. La FCC des ltats-unis stipule que cet appareil doit tre en tout temps loign dau moins 20 cm des personnes pendant son functionnement. Information for the OEM Integrators This device is intended for OEM integrators only. Please see the full grant of equipment document for restrictions. Label Information to the End User by the OEM or Integrators If the FCC ID of this module is not visible when it is installed inside another device, then the outside of the device into which the module is installed must be label with Contains FCC ID: XCO-HSDWAM83 and IC: 7756A-HSDWAM83.