all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 1.07 MiB | ||||
1 | Block Diagram | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Users Manual | Users Manual | 1.07 MiB |
Webthru SWC 306 Users Guide This manual is for Webthru SWC 306 Firmware version 1.4.0. If you have later version of firmware, please download the last updated users guide from Samsung Web Cameras homepage. (www.webthru.net) System Requirements For Webthru SWC 306 10 Base-T LAN
(Leased line, xDSL, Cable Modem, ISDN) For a PC to access Webthru SWC 306 Processor: Pentium II and above RAM: 64MB and more OS: Windows 98/NT/2000 Web browser: Internet Explorer 5.0 and above Screen Resolution: 1024 X 768 pixels and above Version 1.0 SAMSUNG TECHWIN CO., LTD. http://www.webthru.net FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Disposal of used batteries according to the general recommendations against the environmental Important Notice 1. Webthru SWC 306 is not weatherproof. Please note the environmental specifications that are included in the manual. For outdoor usage, equip a weatherproof case to protect the Webthru SWC 306 from water, moisture, or extreme temperature changes (higher or lower than the specifications noted below). The Webthru SWC 306 can be cleaned by gently wiping with a clean dry cloth. 2. Be sure to use the DC adapter that is provided by Samsung Techwin Co., Ltd. Connecting Webthru SWC 306 directly to an AC current may cause damage to the Webthru. 3. Be cautious in handling Webthru SWC 306 Physical shock such as dropping the unit may damage the Webthru SWC 306 and void warranty. 4 The Webthru SWC 306 is made of metal. Be sure that it is fastened tightly during installation to avoid any human injuries. Make sure to place away from the reach of children. 5. If Webthru SWC 306 does not operate properly, please contact your Samsung Techwin distributor for after sales service. Unauthorized personnel are prohibited from disassembling the product. Disassembly will automatically result in void of service warranty. 6. Camera surveillance laws may differ for each country and from province to province. Contact the local region representative to avoid any violations and to apply for authorized purposes only. 2 Webthru SWC 306 Users Guide CONTENTS I. Introduction........................................................................................................................................ 5 II. Product Description ......................................................................................................................... 6 1. Contents....................................................................................................................................... 6 2. Webthru SWC 306 View and Descriptions.................................................................................. 6 3. RS232/RS422/RS485 Descriptions ............................................................................................. 7 4. Description on LED of Ethernet Port .......................................................................................... 8 5. Descriptions on DIP Switches ..................................................................................................... 8 III. Webthru SWC 306 Installation Summary, Connection & Placing............................................ 9 1. Installation Summary................................................................................................................... 9 2. Connecting................................................................................................................................... 9 IV. Installing Webthru SWC 306 Setup Program.............................................................................. 9 V. Assigning IP Address and Configuring Administrators Condition.......................................... 10 1. Connecting Webthru SWC 306 to a PC..................................................................................... 10 1) Connecting Webthru SWC 306 on Internet or LAN.......................................................... 10 2) Connecting Webthru SWC 306 to a PC............................................................................. 10 2. Assigning IP address and Configuring administrators condition with Setup program..............11 1) Starting Setup Program for Webthru SWC 306..................................................................11 2) Configuring Administrators Conditions ............................................................................11 3. Assigning IP Address with ARP command.................................................................................11 1) Using ARP in Windows 98 and NT ....................................................................................11 2) Verifying Installation ......................................................................................................... 12 VI. Accessing Webthru SWC 306 Homepage & Monitoring Real-time Image............................... 13 1. Starting Web browser................................................................................................................. 13 2. Login page ................................................................................................................................. 13 1) ID and password ................................................................................................................ 13 2) Behind Firewall ................................................................................................................. 13 3) Webthru Active-X for MS Explorer User .......................................................................... 13 4) Webthru Java Applet for Macintosh or Unix system User................................................. 13 5) FAQ ................................................................................................................................... 13 3. Various viewers in Webthru homepage...................................................................................... 14 1) Real time monitoring through Default Single Viewer ....................................................... 14 2) Real time monitoring through Default Multi Viewer ........................................................ 17 3) Real time monitoring through Server Push Viewer ........................................................... 17 VII. Configuring Administrators Condition at Webthru SWC 306 Homepage .............................. 19 1. Administrator Login .................................................................................................................. 19 1) Accessing through setup program...................................................................................... 19 2) Accessing through Web browser........................................................................................ 19 2. Configuring Administrators Condition at Homepage............................................................... 19 1) System Configuration........................................................................................................ 19 2) User Configuration ............................................................................................................ 20 3) Network Configuration...................................................................................................... 20 4) Dynamic IP registration service for ISDN and xDSL users .............................................. 21 5) How to find a registered Webthru in Webthru Internet homepage .................................... 22 3 Webthru SWC 306 Users Guide 6) Security Configuration ...................................................................................................... 23 7) Video Configuration .......................................................................................................... 26 8) Application Configuration ................................................................................................. 27 9) Pan/Tilt/Zoom Configuration ............................................................................................ 28 10) Serial Port Configuration................................................................................................. 29 11) Digital I/O Configuration................................................................................................. 30 12) Alarm Configuration........................................................................................................ 30 13) User Custom Configuration............................................................................................. 30 14) Goto Viewer Page............................................................................................................ 31 Detailed Specifications of Webthru SWC 306 .................................................................................. 32 1. General....................................................................................................................................... 32 2. Network ..................................................................................................................................... 32 3. Mechanical................................................................................................................................. 33 4. Compatible external devices and software ................................................................................ 33 5. Environmental ........................................................................................................................... 33 4 Webthru SWC 306 Users Guide I. Introduction What is Webthru SWC 306?
The Webthru SWC 306 is a network CCTV camera server solution with an integrated Internet server, image compression device, flash memory, and many other features. No other hardware is necessary for use. The Webthru SWC 306 relays video source from a CCTV camera to network and provides real time images over networks and the Internet. Simply provide power and connect LAN cable and video cable to the Webthru SWC 306. Webthru SWC 306 utilizes Wavelet image compression and Linux operating system. Wavelet and Linux enable Webthru SWC 306 to transfer high quality images faster and with a greater degree of reliability than standard JPEG systems. Features and Benefits Ease of Use Webthru SWC 306 requires Microsoft Internet Explorer 5.0 (or higher) for use. Windows 2000 is recommended for best results. Connect Webthru SWC 306 to the Internet and it is ready for use. Compatible with most Systems and Protocols Webthru SWC 306 supports TCP/IP networking, SMTP, HTTP and other Internet-related protocols. In addition, the Webthru SWC 306 can be used in mixed operating system environments, such as Windows, UNIX, Macintosh and OS/2. Webthru SWC 306 also integrates easily into other Internet/Intranet applications and CGI scripts. Simple Administration - Webthru SWC 306 can be configured and managed directly from its own web page. Moreover, as new upgrades become available, it is easy to upgrade Webthru SWC 306 remotely over the network. Wavelet Image Format - Unlike many other products that need to fracture image files prior to broadcast, the Webthru SWC 306 delivers complete, highly compressed pictures in Wavelet format. Wavelet has image compression rates 30-300% higher than standard JPEG. By utilizing Wavelet, image file sizes are much smaller than conventional camera servers and Wavelet's image quality is superior to other camera servers as well. Wavelet can transmit up to 123 frames per second. External Device Connection - External devices such as IR-sensors, switches, alarm relays and external video input can be connected to Webthru SWC 306 via six auxiliary Input ports. Users Programmable Space Webthru SWC 306 contains 4.5MB of configurable Flash Memory for user-
programmable and user-configurable space. Because Webthru SWC 306 also acts as a server, this space can be used to create a personal web page. Embedded Linux Operating System Webthru SWC 306 uses an embedded Linux operating system within its 32bit RISC CPU. Linux is based on UNIX and is one of the most stable operating systems available. There is very little chance of the operating system crashing. 5 Webthru SWC 306 Users Guide II. Product Description 1. Contents
* Unpack and check all the items as below. Item Webthru SWC 306 Manual Crossover Cable Direct Cable Adapter & Power Cable Accessories CD ROM title Description Remarks Network server for CCTV camera Webthru SWC 306 User's Guide 1 m crossover cable 2 m direct cable DC 12V, 1.0A brackets for 19-inch rack bracket for connecting two SWC 306 Screw for bracket Setup program and manual Provided on CD Red-colored White-colored 2 1 8 2. Webthru SWC 306 View and Descriptions RS232/RS422/RS48 Sensor In Alarm Network Link DIP Switch Video Input AC 24V DC 12V Connector Name Description DIP switch To designate video signal termination of Video Input BNC connector BNC connector CH1 ~ CH6 To input video signal through a coaxial cable AC 24V DC 12V RJ-45 Ethernet port Link port RS232/RS422/RS485 To connect a power supply unit of 24V AC To connect a power supply unit of 12V DC To connect 10 Base-T Ethernet cable Stackable up to three boxes only with one IP To communicate between external devices. These pins are for devices that satisfy RS-232, RS422, or RS485 6 Webthru SWC 306 Users Guide Sensor In Alarm Out To input video signal through 6 coaxial cables To output video signal through 6 coaxial cables 3. RS232/RS422/RS485 Descriptions RS485 S+
S-
P G Rx Tx G R+ R-
T+ T-
RS232 RS422 Connector Name Power Ground Description To supply power to external devices To ground cables of power, communication, etc. RS-232 RS-422 RS-485 To communicate between Webthru SWC 306 and external devices such a CCTV camera or an external modem. These pins are for devices that satisfy RS-232C protocol, and they are consisted in RX and TX. To communicate between Webthru SWC 306 and a CCTV camera that satisfies RS-422 protocol. They are half-duflex. It is consisted in R+, R-, T+, and T-. To communicate between Webthru SWC 306 and a CCTV camera that satisfies RS-485 protocol. They are consisted in S+ and S-. 7 Webthru SWC 306 Users Guide 4. Description on LED of Ethernet Port Yellow LED: This LED indicates the status of data transmission. After power is supplied, it is on for the first 4-5 seconds and then it goes off. And it blinks continuously when a user access Webthru and Webthru transmits data. Green LED: This LED indicates the status of networking. After power is supplied, it is on for the first 1-2 seconds, and then it blinks once at every one second as long as the network is connected. 5. Descriptions on DIP Switches D I P S w i t c h 1 2 3 4 5 6 O N Hi-Z 7 5 75ohm O F F To configure the function of the six coaxial cable ports at the rear of Webthru SWC 306. You can configure the relevant channels with each switch. If you connect two CCTV cameras(1Vp-p
/75ohm) to Video Inputs and monitor real time video through 1 and 2 channels, place the two DIP switches
(marked with No. 1 and 2) at 75ohm position. 8 Webthru SWC 306 Users Guide III. Webthru SWC 306 Installation Summary, Connection & Placing 1. Installation Summary
Connect Ethernet and Power to Webthru on local network for configuration.
Install Webthru Setup Program into a PC on local network.
Assign an IP address to Webthru and configure administrators condition.
Configure users condition.
Place Webthru, re-connect power and Ethernet. 2. Connecting
Connect Ethernet line to the Ethernet port in the rear.
Connect the power supply.
Confirm that the LED of the Ethernet port blinks. IV. Installing Webthru SWC 306 Setup Program
Insert the Webthru Setup disk.
Drag the Webthru Setup icon onto the desktop.
Double-click on the icon. 9 Webthru SWC 306 Users Guide V. Assigning IP Address and Configuring Administrators Condition 1. Connecting Webthru SWC 306 to a PC 1) Connecting Webthru SWC 306 on Internet or LAN Use the direct cable (white colored one) to connect Webthru SWC 306 to Internet or LAN. With this connection, remote users will not be able to access Webthru until local user configures Webthrus network setting. Internet Dedicated line, xDSL line, cable modem line, and ISDN line are available. Router HUB Remote User Local User Direct cable Connect Webthru to a PC through a HUB. 2) Connecting Webthru SWC 306 to a PC Use the crossover cable (red colored one) to directly connect Webthru SWC 306 to a PC. This connection is to be used to configure Webthru. Crossover cable Connect Webthru directly to a PC through LAN ports. 10 Webthru SWC 306 Users Guide 2. Assigning IP address and Configuring administrators condition with Setup program 1) Starting Setup Program for Webthru SWC 306 Click the WebthruSetup.exe file on your PC. When the Setup Program is executed, the setup program detects and shows every Webthru connected on the local network. From the Webthrus listed, select one to assign a new IP address. (Default is 211.53.133.92) To choose a Webthru, click on its MAC Address or IP address. When a Webthru is selected, its IP address will appear in the Selected IP Address box. Type a password in the Admin.s Password box to change the IP address, reboot Webthru, or start configuration. The default password is admin. To change the IP address, enter the Admin.s password and click Change IP Addr. Enter the new IP address and click OK. OK The Reboot button will reboot the Webthru. This process takes 10-20 seconds. 2) Configuring Administrators Conditions To access the Webthrus Administrators Page from the Setup Menu, enter the admin.s password and click the Start Configuration button. (For more detailed information, refer to Chapter VII Configuring Administrators Condition at Homepage) 3. Assigning IP Address with ARP command 1) Using ARP in Windows 98 and NT When using Webthru with Windows 98 and Windows NT, follow the steps below. Open a DOS window and type the following commands. arp -s <Webthru IP address> <Webthru Ethernet address>
ping -t <Webthru IP address>
Example arp -s 192.168.1.3 00-40-8c-10-00-86 ping -t 192.168.1.3 11 Webthru SWC 306 Users Guide 2) Verifying Installation After successfully completing the above procedures, the following message (or similar) will appear on the screen. Request timed out
Request timed out Reply from 200.243.232.178: bytes=32 time=2ms TTL=255 Reply from 200.243.232.178: bytes=32 time=2ms TTL=255 Ping statistics for 200.243.232.178:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milliseconds:
Minimum = 1ms, Maximum = 2ms, Average = 1ms If the above ping reply does not appear, press 'F3' and 'Enter' keys. Normally Request timed out messages appear 7 times before replying properly. Once the above ping reply appears press <Ctrl>+<C> keys to make it stop. When the ping replies stops, data loss may range from 0% to 99%. This is normal. If the statistic shows 100% loss, check the following criterions: (a) network line and connection status are stable; (b) IP address assigned to Webthru is available; (c) PC and Webthru have the same local network IP address. Same local IP address of C grade network means that first 3 sets of numbers are the same but the fourth set is different. For example 192.168.1.2 and 192.168.1.3 are in the same local network. (If there is a Network Mask on the network, this can be an exception. For detailed information on IP, refer to appendix 3) 12 Webthru SWC 306 Users Guide VI. Accessing Webthru SWC 306 Homepage & Monitoring Real-time Image After assigning Webthru an IP address, the Webthru can be configured within its self- contained homepage through any standard Web browser on a local network. However access to its Homepage by a remote network is not possible until gateway address, subnet mask, and broadcast address have been properly assigned. 1. Starting Web browser Start the web browser and enter the Webthru IP address. This will access the Webthru login homepage. 2. Login page 1) ID and password The login page allows only registered Webthru users to view images from Webthru. To connect to Webthru and view real-time images, follow the login procedures. The default name and password for the user is guest. The default Admin username and password is admin. Both may be changed at the Admin page, but neither the ID nor password can be more than nine characters long. 2) Behind Firewall If the PC is connected on a network where firewall is, real time image will not be viewed properly because video TCP port of Webthru is blocked. To connect Server Push Viewer directly at Webthru homepage, click on Behind Firewall menu. 3) Webthru Active-X for MS Explorer User Systems using Microsoft Explorer require Active-X Control program. The program will usually be installed automatically when a user accesses a Webthru. A pop-up window will appear for Active-X installation, click yes. If images still do not appear after installation, check the c:\windows\download program files folder
(for Windows 2000 NT, the directory is c:\WINNT\download program files). The file name is Web Camera Server Control. If the file is downloaded, but images cannot be seen, delete the file and re-install. 4) Webthru Java Applet for Macintosh or Unix system User Java Applet viewer is for systems that do not use MS Windows. Macintosh OS or Unix can be used with the Java Applet viewer. Java Applet viewer requires java virtual machine that should already be installed on users computer. 5) FAQ Frequently asked questions and answers are provided here for troubleshooting. If user has other questions, please contact Samsung Web Camera homepage through http://www.webthru.net. 13 Webthru SWC 306 Users Guide 3. Various viewers in Webthru homepage There are 3 viewers for real-time monitoring in the Webthru homepage: Default Viewer, Server-Push Viewer, and Java Applet Viewer. An administrator may set 3 different viewers as main viewer. (Single Viewer, Multi Viewer, and Server Push Viewer) 1) Real time monitoring through Default Single Viewer
(1)
(2)
(3)
(4)
(5) At default viewer, a user may configure image transmission method and control integrated PTZ mechanism of a CCTV camera. The PTZ control panel is activated in some seconds depending on network speed.
(1) Single View / Multi View The Multi View allows the monitoring of other images from additional cameras connected to the Webthru. If you press the Multi View, you can view six images simultaneously. Please note that transmission speed cannot exceed 30 fps, and additional images will make overall transmission speed slow. Single View monitors a single channel. Click on the appropriate button for single view or multi view.
(2) Image Control Resolution Select the level of resolution from 5 levels (720x486, 720x243, 360x243, 180x121, 90x60). Higher-resolution images are larger file sizes and are transmitted at slower speed. Expansion Expansion enlarges the image from 1X to 4X. However, expansion (2X to 4X) does not increase images resolution, hence the clarity of an expanded image will not be as good as the original. Frame rate To control image transmission speed. Fastest, will receive images at the fastest speed possible within the network environment. The transmission speed is dependent on the network lines capacity and user PCs 14 Webthru SWC 306 Users Guide performance. Webthru can transmit up to 30 frames per second, but total frames transmitted by all 6 channels cannot surpass the maximum rate of 30 fps.
(3) Camera selection Select cameras to monitor. User may select one specific camera or all 6 cameras.
(4) Transmission Control Gray Mode On Images are displayed in black and white. Images can be transmitted at a higher speed under gray mode. Single Shot Mode On When this button is clicked, one frame of image is reproduced. Therefore, no other images may be viewed. Channel Rotate Mode On Images are viewed one after another as channel number. It may be configured by second.
(5) Play Control Pan/Tilt To move the direction of external camera to where to want to see. Zoom To zoom the image in and out. Focus To control and optimize the images focus. Accel. Rate To control the moving speed of the Pan / Tilt mechanism. There are three settings. Accel. does not control zooming speed. This can be adjusted with the mouse. By clicking the right mouse button on the image, a pop-
menu with five options will appear. The Focus Sensitivity controls zooming speed from level 1 to 10. Play/Stop: Webthru generates and transfers the real-time images as soon as it is accessed. To stop transferring images, click the Stop button. To resume transfer, click Play button.
(6) Other Function Buttons Capture To save a frame of still image transmitted from Webthru. A still image can be saved as a format of bitmap
(*.bmp) or Wavelet method file (*.eye). Wavelet compression image file can be decompressed and reproduced on Internet browsers such as Explorer. Another method to capture a still image is: Place the mouse on the image; Click the right mouse button; Select the Save As File option from the pop-up menu. Server-Push Viewer To go to the server-push viewer. FAQ It lists frequently asked questions and answers. 15 Webthru SWC 306 Users Guide Admin To access administration page. (Refer to Chapter VII Configuring Administrators Configuration at Homepage)
(7) Convenient pop-up menu A small window of 5 menus appears when you click the right button of the mouse. However only users who are permitted can utilize the functions such as Quality Box, Focus Sensitivity, and Image Quality. Image Info and Save As File menus are permitted to any user. And the results of the four functions except Save As File are to be affected in every image that is transmitted to all users. (For detailed information, refer to User Configuration in Chapter VII). And in server push viewer, only Image Info and Save As File menus are supported. Image Info You may decide the color (black or white) of the information that is shown on the left top of the image. And you may leave out the information. Quality Box This is to set a certain area clear and remained area dull. You can overcome insufficient network bandwidth with this function, because the file size is reduced with unfocused area. Quality Box is to be set like under written description. Choose New QBOX button. Place mouse cursor on a certain point of real time image where to start QBOX. Click and drag the mouse point. You can also re-use previous QBOX area to focus again by clicking Enable QBOX. Disable QBOX is to finish. The image activated Focusing Area function is seen in the right. The image quality of outer area of QBOX is to be set with Ambient Level menu. The level is from 1 to 5. If you select Level 1, the quality is similar to focused area. And if you select Level 5, the unfocused area is shown dark. A user who has Video control right may utilize this menu. Focus sensitivity You may configure movement degree of zoom mechanism. The sensitivity is from Level 0 to Level 9. By selecting Level 9, user zooms in or out at the largest degree. A user who has PTZ control right may utilize this menu. Image quality It is to set image quality. The image quality is from Level 0 to 9. If user chooses the Level 9, Webthru sends the finest image. However, transmission frame rate will be reduced because of large sized data. If user chooses Level 0, Webthru sends dullest image but fast. A user who has Video control right may utilize this menu. Save As File It is to save a frame of still image as an electric file. A still image can be saved as bitmap (*.bmp) file or Wavelet format file (*.eye). Wavelet formatted image file is to be reproduced on Internet Explorer as long as the PC is installed Active-X program. The very image that is shown at the moment when you click the menu is saved. 16 Webthru SWC 306 Users Guide
(8) Placing a company logo The Webthru logo, located on the left bottom of the viewer, can be replaced with a different company logo. 2) Real time monitoring through Default Multi Viewer
(1) Single View / Multi View You can select a mode between single view and multi view. The button is toggled between the two functions.
(2) Play/Stop Webthru generates and transfers six real-time images as soon as it is accessed. To stop transferring images, click the Stop button. To resume transfer, click Play button.
(3) Camera selection Select the camera to configure a frame rate.
(4) Frame Rate Control image transmission speed. Fastest, will receive images at the fastest speed possible within the network environment. The transmission speed is dependent on the network lines capacity and user PCs performance. Webthru can transmit up to 30 frames per second, but total frames transmitted by all 6 channels cannot surpass the maximum rate of 30 fps. 3) Real time monitoring through Server Push Viewer If Webthru is installed on a network where firewall is, you may access Webthru through server-push viewer to monitor real-time images.
(1)
(2)
(3)
(4)
(1) Image Control Extension menu is not supported. Image Size Select the level of resolution from 5 levels (720x486, 720x243, 360x243, 180x121, 90x60). Higher-
resolution images are larger file sizes and are transmitted at slower speed. 17 Webthru SWC 306 Users Guide Frame Rate Control image transmission speed from 5 levels (fastest, 10fps, 5fps, 3fps, 1fps). Fastest, will receive images at the fastest speed possible within the network environment. The transmission speed is dependent on the network lines capacity and user PCs performance.
(2) Camera Select cameras to monitor. User may select one specific camera to monitor real-time image.
(3) Transmission Control On this viewer, Channel Rotate Mode On menu is not available. Gray Mode Images are displayed in black and white. Images can be transmitted at a higher speed under gray mode. Single Shot Mode When this button is clicked, one frame of image is reproduced. Therefore, no other images may be viewed.
(4) Play Control Pan/Tilt: To move the direction of external camera to where to want to see. Zoom: To zoom the image in and out. Focus: To control and optimize the images focus. Accel. Rate: To control the moving speed of the Pan / Tilt mechanism.
(5) Convenient pop-up menu Quality Box, Focus Sensitivity, and Image Quality menus are not supported. Image Info You may decide the color (black or white) of the information that is shown on the left top of the image. And you may leave out the information. Save As File It is to save a frame of still image as an electric file. A still image can be saved as bitmap (*.bmp) file or Wavelet format file (*.eye). Wavelet formatted image file is to be reproduced on Internet Explorer as long as the PC is installed Active-X program. The very image that is shown at the moment when you click the save button is saved.
(6) To Home This button returns to the default viewer.
(7) Capture This button is to save a frame of still image transmitted from Webthru. This function is the same with Save As File menu.
(8) Admin It is to access administration page. (Refer to Chapter VII Configuring Administrators Configuration at Homepage)
(9) FAQ User may refer FAQ for trouble-shooting in installing or running Webthru. 18 Webthru SWC 306 Users Guide VII. Configuring Administrators Condition at Webthru SWC 306 Homepage This page is for administrator. Administrator may control operating status remotely. This page can be accessed through Setup program by clicking Start Configuration button. 1. Administrator Login 1) Accessing through setup program Select Webthru by clicking on the MAC address or IP address. Then type in the administrators ID and password (Default ID and password are admin), and click Start Configuration button. The setup program automatically connects to the Admin page of Webthru Homepage. 2) Accessing through Web browser On Web browser, a user may access Webthru login page with its IP address. In the login page, a user may key in administrators ID and password or a normal users ID and password. With any of ID and password, the user may access real time image viewer page. 2. Configuring Administrators Condition at Homepage 1) System Configuration This page is to set name, date &
time, location, and description of ones Webthru. Model, serial number, and software version appear automatically.
(1) Webthru Name The name is to be used to register the Webthru on a certain server, if dynamic IP address is used. Therefore it is very important to set a proper name for user the Webthru in the dynamic IP registration list. (For detailed information, refer to Dynamic IP Registration Service for ISDN, xDSL User) to find
(2) Model By clicking Detailed H/W Information, administrator may view the detailed hardware information such as maximum numbers of channel, serial port, digital input, digital output, etc. The model name is marked automatically.
(3) Installation Location & Additional Description The information is to show in a dynamic IP registration list.
(4) Date & Time There are three date & time menus. In Webthru Current Date & Time panel, the date and time that is set in the Webthru appears. In System (PC) Current Date & Time panel, the same date and time that is set in users PC appears. To synchronize the Webthru and PC date and time, an administrator can click the Time 19 Webthru SWC 306 Users Guide Synchronization button. The Manual Date & Time panel allows the user to set date and time.
(5) Administrators E-mail Address In this panel, administrator records ones e-mail address. If administrator put a contact menu of e-mail communication on real time image viewer page, the linked e-mail address to the contact menu is to be synchronized with this. So administrator can keep up e-mail address easily.
(6) Initialize Flash Info This will initialize almost all the information saved on Flash Memory. However Date & Time, Model, Serial Number, and IP configuration of System Configuration, and Video Signal Type of Video Configuration menus will not be changed.
(7) Rebooting If Webthru has any problems, administrator can reboot it without adjusting power supply. This button works as on/off switch. 2) User Configuration This page is to configure IDs and passwords of an administrator and 5 users. are
(1) User Account There administrators account and 5 users accounts. Account name can be changed. one
(2) Password If you want to open your Webthru to everyone, you may not change default users ID and password. However you should change administrators ID and password as unique ones.
(3) Access Rights Administrator may give or take users right of PTZ control and video control. With default setting, administrator has both right of PTZ control and video control and normal user doesnt have any right. Video control: This is to control pop-up menus such as image quality level and QBOX settings. PTZ control: This is to control Focus Sensitivity in pop-up menu and to control PTZ mechanism of a CCTV camera. 3) Network Configuration This page is to define network type and set network addresses of Webthru.
(1) DHCP Client Protocol DHCP (Dynamic Host Configuration Protocol) is to manage host address on a network. With this protocol, every host on a LAN may share limited official IP address for Internet access. In other words, every host on a LAN may lease official IP address from DHCP server temporarily.
(2) Select Network Interface This is to select proper network interface with which Webthru is connected. 20 Webthru SWC 306 Users Guide If Webthru is connected with Internet dedicated line, cable modem line or on LAN environment, you should select network interface as Ethernet. If Webthru is connected on xDSL line that needs PPPoE process to connect on Internet, administrator should select xDSL (PPPoE).
(3) Ethernet Interface Administrator may configure IP address, subnet mask, broadcast address, gateway address, and DNS addresses of Webthru. For broadcast address, administrator may set it automatically by clicking Get From Netmask button after assigning IP address and subnet mask. This interface is mainly used for Internet dedicated line and LAN, and sometimes for xDSL line as it is explained on DHCP Client Protocol setting. MTU Size: Depending on network type, administrator may set data packet size with this menu to utilize the network at most effectively. DNS Server IP Address: This is used when you register your Webthru on dynamic IP registration list of SWR (Webthru Registration Server). SWR has its domain name of Webthru.to and the domain name is registered on DNS servers on the world.
(4) xDSL Interface If Webthru is connected on xDSL line and needs PPPoE process, administrator should select network interface as xDSL (PPPoE). And administrator should configure user ID and password for PPPoE. ID and password may be acquired from the ISP that installed the line. 4) Dynamic IP registration service for ISDN and xDSL users This page is to register Webthru on dynamic IP registration server. is IP If Webthru installed on a network of dynamic IP address
(floating address), administrator should register the IP Webthru registration give common users simple connectivity. If not, no one can access the Webthru through Web browser. It is because that no one knows IP address which one can access the Webthru with. dynamic to server on 21 Webthru SWC 306 Users Guide To solve the problem, Samsung Techwin runs a server making a list of Webthrus that have dynamic IP addresses. On the server, Webthru registers its information such as name, location, and description, so those common users may detect a certain Webthru. Name, location and description are assigned at System Configuration page. If administrator does not change them, the Webthru will register default information on the list, and it will be very difficult to point out and access a certain Webthru. The list is on an Internet homepage of Webthru (www.webthru.to).
(1) Auto IP Registration Function Administrator may register ones Webthru by enabling Auto IP Registration Function. Registration process is that Webthru detects IP addresses from DHCP server and informs the detected IP addresses to dynamic IP registration server.
(2) Registration Server Address This is to configure a server address for registration. The registration server to be used for Dynamic IP registration should be installed proper S/W, developed by Samsung Techwin Co., Ltd.
(3) Registration Interval Dynamic IP addresses are commonly used with xDSL, ISDN or Cable Modem lines. In order to maintain continuous connectivity, user should reset the Registration Interval at a shorter time interval than the default value.
(4) Add Public List There are two registration systems. One is to register on a public list and the other is on a private list.
(5) Access Token Access token is a password and it is used when you register your own Webthru on a list Users Webthru out of all Webthrus on SWR(Webthru Registration Server). 5) How to find a registered Webthru in Webthru Internet homepage On Webthru Internet homepage (www.webthru.to), there are menus to find the Webthru that is registered on SWR (Webthru Registration Server).
(1) Sign up membership To search your Webthru out of a public list or a private list, sign up membership first. You may sign up on the server through Membership menu.
(2) Finding Webthru from public list To access Webthru that is registered on public list, you may find it through Service menus. Once click SWR menu, you may find SWR (Webthru Registration Service) Webthru list on SWR page that is a main page of the Service menu.
(3) Finding Webthru from private list To access Webthru that is registered on private list, you should make your own Webthru list before. You may make the list through My Webthru menu. My Webthru List: You may maintain your own Webthru registering it on this list. When you login this 22 Webthru SWC 306 Users Guide homepage, SWR (Webthru Registration Server) detects and shows all the Webthrus that you listed appear on your own list. Webthru Add & Delete: This menu is to append a certain Webthru on your own list. You may append Webthru on your own list as follows. Key in serial number(e.g. W100000000000), MAC address(e.g. 00:00:00:00:00:00), and access token of a certain Webthru in the box. Click Append menu. SWR (Webthru Registration Server) searches a corresponding Webthru with the conditions from both Public List and Private List and registers the Webthru on your own list. 6) Security Configuration This is to filter a certain IP addresses from accessing Webthru based on network masking.
(1) IP/Subnet Filtering Mode You may allow or deny a certain user to access your Webthru with enabling this menu. Default Policy This is to decide the principle of IP/Subnet Filtering Mode between allow and deny. How to register allowed/denied user in the list Network masking is to mask network ID for every existing IP address in the world. Therefore the IP addresses that have the same network ID are to be applied with a command of Allow or Deny. The masked bits are considered as network ID. Note: To explain and understand easily on IP address, the first byte of IP address is marked as X1 in this manual. And X2 is for the second byte, X3 is for the third byte, and X4 is for the fourth byte. IP address is constructed as follows. IP address construction in binary number of each bit xxxxxxxx (8 bit): X1 xxxxxxxx (8 bit): X2 xxxxxxxx (8 bit): X3 xxxxxxxx (8 bit): X4 27 26 25 24 23 22 21 20 27 26 25 24 23 22 21 20 27 26 25 24 23 22 21 20 27 26 25 24 23 22 21 20 E.g. IP address in binary: 11000000. 10101000. 00000001. 00001101 (It is equal to 192.168.1.13)
* Binary number 1 means to take the equivalent decimal number (27, 25, etc) and 0 means to disregard it. IP address construction in decimal number of each byte xxx (0-255: 1 byte): X1 xxx (0-255: 1 byte): X4 128 64 32 16 8 4 2 1 128 64 32 16 8 4 2 1 128 64 32 16 8 4 2 1 128 64 32 16 8 4 2 1 xxx (0-255: 1 byte): X2 xxx (0-255: 1 byte): X3 23 Webthru SWC 306 Users Guide E.g. IP address in decimal: 192. 168. 1. 13 (It is equal to 11000000. 10101000. 00000001. 00001101)
* Binary number 1 means to take the equivalent decimal number (27, 25, etc) and 0 means to disregard it. Network masking point is to be expressed with decimal number from 0 to 31. IP address is consisted in 4 bytes. 4 bytes are 32 bits. Network is to be masked on every bit from the first bit to the 32nd bit. Masked bit is marked with binary number 1, and the corresponding bits out of provided IP address are defined as network ID for IP filtering. Network masking point (0 to 31) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 0 E.g. Network masking on the 8th bit (8): 11111111. 0000000. 00000000. 00000000 (255.0.0.0) E.g. Network masking on the 16th bit (16): 11111111. 11111111. 00000000. 00000000 (255.255.0.0) E.g. Network masking on the 24th bit (24): 11111111. 11111111. 11111111. 00000000 (255.255.255.0) E.g. Network masking on the 32nd bit (0): 11111111. 11111111. 11111111. 11111111 (255.255.255.255) According to masking point, masked network ID is to be different out of the same IP address. For example, if IP address is described as 192.168.1.13 (11000000.10101000.00000001.00001101) with masking point 24
(255.255.255.0), with 11000000.10101000.00000001.xxxxxxxx (28 (256) pieces of IP addresses) will be allowed or denied from Webthru. addresses consisted address whose the IP IP is If you describe an IP address as 192.168.1.13 and put masking point 26 (255.255.255.192), the masked bits are the first 26 digits and network ID masked as 11000000.10101000.00000001.00. In this case, the IP addresses whose IP address is consisted with 11000000.10101000.00000001.00xxxxxx (26 (64) pieces of IP addresses) will be applied with a command of Allow or Deny. Applied IP address number according to masking point 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 0 231 230 229 228 227 226 225 224 223 222 221 220 219 218 217 216 215 214 213 212 211 210 29 28 27 26 25 24 23 22 21 20 E.g. Masking point 8: 224 pieces of IP addresses are applied E.g. Masking point 16: 216 pieces of IP addresses are applied E.g. Masking point 24: 28 pieces of IP addresses are applied E.g. Masking point 0: 20 pieces of IP address (itself) is applied Though masking point is to be any bit out of 32 bits, it is common to point on the bits of host ID part. If the masking point is placed on network ID part, the range is expanded compared to the provided IP address. Network class is divided as follows. D and E class networks are not to be used by normal user. Class Decimal number of X1 byte Network ID A B C D 0 to 127 128 to 191 192 to 223 224 to 239 X1 X1, X2 Host ID X2, X3, X4 X3, X4 X1, X2, X3 X4 For Multicasting utilization 24 Webthru SWC 306 Users Guide E 240 to 255 Reserved for specific utilization In C class network, the applied number of IP addresses with network masking is as below when you mask on host ID part (X4: the fourth byte). Masking on X4 Byte 25 128
(128) Masked 26 64
(192) Free Masked Masked 27 32
(224) Free Free 28 16
(240) Free Free Free Masked Masked 29 8
(248) Free Free Free Free 30 4
(252) Free Free Free Free Free Masked Masked Masked 31 2
(254) Free Free Free Free Free Free 0 1
(255) Free Free Free Free Free Free Free Remark Masking Point Decimal Number
(Accumulated Value) 7 digits are free 6 digits are free 5 digits are free 4 digits are free 3 digits are free 2 digits are free 1 digits are free No free digit Host ID number 27 = 128 26 = 64 25 = 32 24 = 16 23 = 8 22 = 4 21 = 2 20 = 1 The most common case is to make subnet through network masking, and it is to divide a network into some smaller network. If provided IP address is 192.168.1.2, you may divide the whole network into 2 sub-
networks and allow or deny only the IP addresses that belong to one of sub-networks. With setting as follows, The IP address of 192.168.1.2 is divided into two sub-networks and allow for the IP address out of the first sub-network to assess Webthru. Default Policy: Deny IP address: 192.168.1.2 Masking: 25 (255.255.255.128) Then only the IP addresses from 192.168.1.0 to 192.168.1.127 are to access Webthru, while the IP addresses from 192.168.1.128 to 192.168.1.255 and any other IP address are to be denied accessing Webthru. Changing IP address can reverse the result. If you set IP address as 192.168.1.130, only the IP addresses from 192.168.1.128 to 192.168.1.255 are to access Webthru. And the IP addresses from 192.168.1.0 to 192.168.1.127 and any other IP address are to be denied accessing Webthru. You may refer below table to figure out masking point from network information that is given from your ISP or network administrator. Masking Point Masked bit (Network ID) Netmask in decimal number 1 2 3
. 8 9
. 16 The first bit From the first bit to the second bit From the first bit to the third bit 128.0.0.0 192.0.0.0 224.0.0.0
. From the first bit to the 8th bit From the first bit to the 9th bit From the first bit to the 16th bit
. 255.0.0.0 255.128.0.0 255.255.0.0 25 Webthru SWC 306 Users Guide 17
. 24 25 26 27 28 29 30 31 0
. From the first bit to the 17th bit From the first bit to the 24th bit From the first bit to the 25th bit From the first bit to the 26th bit From the first bit to the 27th bit From the first bit to the 28th bit From the first bit to the 29th bit From the first bit to the 30th bit From the first bit to the 31st bit The 32nd bit 255.255.128.0
. 255.255.255.0 255.255.255.128 255.255.255.192 255.255.255.224 255.255.255.240 255.255.255.248 255.255.255.252 255.255.255.254 255.255.255.255
* Masking on 32nd bit has the same effect as masking none, and in Webthru 0 instead of 32 is used. Masking 32 bits means that all the 32 bits are network ID, and masking none means that all the 32 bits are host ID. Therefore masking all the 32 bits or none means that the provided IP address itself is applied with a command of Allow or Deny. If you want to allow only the IP addresses from 192.168.1.61 to 192.168.70, you may set as bellows. Default Policy IP address IP address IP address IP address 192.168.1.60 192.168.1.60 192.168.1.64 192.168.1.71 Masking Masking Masking Masking Deny 30 0 29 0 Policy Policy Policy Policy Allow Deny Allow Deny
* The IP addresses in black squares can be any IP address of the sub-networks. In the first square, 192.168.1.60 to 192.168.1.63 is to be assigned. And in the second square 192.168.1.64 to 192.168.1.71 is to be assigned.
(2) Image Encryption Mode Administrator may restrict people to receive images from ones Webthru, even though people accessed it. If Image Encryption Mode is enabled and a pin number is assigned, people have to key in the assigned pin number to see image after accessing Webthru image viewers. Security Configuration is a double-checking function to control accessibility, utilizing User Account Configuration at the same time. 7) Video Configuration This page is to configure every channel with various conditions.
(1) Video Channel Selection To select which video channel to configure. In the list, there are 6 video channels.
(2) Video Channel State Control It is to determine which channels will be enabled to send image signals to the image viewer. If a channel with an external source is disabled, no image will appear in the image viewer. However, if a channel without an external source is enabled, the overall transmission speed will go down and no image will appear. To view an image from an external source, the channel with the source must be enabled. 26 Webthru SWC 306 Users Guide
(3) Camera Color Type It is to define whether images from a camera are color or Black/White (B/W). This will not change a cameras original character (color cameras can be viewed in B/W or color, but they are still color cameras). Rather, this is to help define external cameras, and provide information to Webthru.
(4) Video Signal Type It is to define whether the signals of external CCTV cameras are NTSC or PAL.
(5) Camera Installation Angle Webthru can always show images in right angle regardless of cameras installation position. If camera is located on the wall upside down, user can adjust image angel by selecting 90 deg. or 270 deg.
(6) Advanced Configuration Calibration Parameters Administrator can manipulate screen settings by adjusting brightness, contrast, hue, saturation, horizontal line shift, and vertical line shift from the menu. With Video Gain menu, the image may be optimized without adjusting each value of other menus. However Video Gain is not supported currently. It is to be supported in near future. Caption Display Options Administrator can configure caption on real time image with display options such as color and contents. Caption is to be made of time information, channel information, and additional explanation (user defined string). Visual Setting Parameters Administrator can configure QBOX and image quality level with aid of real time image. Place the mouse curse on real time image and click the right button, and pop-up menus will be viewed.
QBOX Parameters: Administrator sets QBOX area with a mouse to click and drag. With Ambient Level menu, Administrator may set quality level of unfocused area in the image (out of the focused range).
Image Quality Level: Administrator chooses image quality level from 0 to 9. Level 9 is the best quality. But transmission speed will be reduced because of larger sized data. The image level inside the QBOX is the same level as is selected in this menu. 8) Application Configuration This page is to configure e-mail and file sending functions.
(1) Select Video Channel It is to select a video channel for configuration.
(2) Recipient E-mail Address This is to designate a person to receive E-mail.
(3) Senders E-mail Address This is to put a persons e-mail address that is considered as the e-mail sender. The e-mail sender can be a person who should take care of the situation when events occur. E-mail will be 27 Webthru SWC 306 Users Guide delivered to a person who is defined as a recipient in the blank of E-Mail Recipient. The person who received e-mail can send a message of countermove to a person who is defined as an e-mail sender.
(4) Check E-Mail Options Relay Mail Server: With the same problem of e-mail blocking, Webthru has a function to relay its e-mail through an available e-mail server so that e-mail can have the relay servers domain name. After activating User Relay Mail Server menu, key in a servers domain name such as @abcdefg.com. Content-Transfer-Type: It is to define e-mail format. E-mail servers support Base64 format in common, but some servers not. In the case, select the format as Quoted Printable.
(5) E-Mail Event Configuration Event source: Administrator should define the triggering event for E-mail delivery among MD (motion detection), sensor 1, sensor 2, sensor 3, sensor 4, sensor 5, and sensor 6. If administrator clicks on sensor1, e-
mail is sent when the sensor 1 detects events. File name: Administrator can name the image files by one of three methods: date & time (DATETIME; e.g. IMG-CH00-2001030-223031.eye), serial number (SEQNUM; e.g. IMG-CH00-SN1.eye), or the administrator can name the file (Manually assigned filename). The image file has the extension .eye to enable reproduction on an Internet browser. Image quality: Administrator may set images resolution that is delivered by e-mail. Resolution is to be set among 90x60, 180x121, 360x243, 720x243, and 720x486. An image of 90 by 60 is of the lowest resolution and the smallest size.
(6) FTP directory configuration Administrator assigns FTP server address, FTP user account, FTP user password, and FTP user path to receive files when events occur.
(7) FTP event configuration Administrator may set sending conditions, image resolution, and file name. Image resolution, filename, and sending conditions setting methods for FTP are same as that of e-mail. 9) Pan/Tilt/Zoom Configuration This page is to decide whether to use pan/tilt/zoom control function or not and select which serial port to use.
(1) Video Channel Selection Administrator selects a video channel for the pan/tilt/zoom mechanism. The four channels shown in the panel 28 Webthru SWC 306 Users Guide are the same as seen on Video Configuration page.
(2) Pan Tilt Function Administrator defines whether to utilize pan/tilt control function or not.
(3) Zoom Function Administrator defines whether to utilize zoom control function or not.
(4) Pan Reverse Mode Function This is to set command reverse direction against to right and left direction control arrows. This function is useful when PT driver is installed upside down.
(5) Tilt Reverse Mode Function This is to set command reverse direction against to up and down direction control arrows. This function is useful when PT driver is installed upside down.
(6) Select Serial Port It is to select a useable serial port as the character of pan/tilt/zoom control receiver. It is to select a serial port between Serial #1 and Serial #2 with which a pan/tilt/zoom control receiver is connected to Webthru. Serial #1 is RS232C interface and Serial #2 is RS422/RS485 interface.
(7) Serial Port Base Address This menu identifies the base address for a video channel and a pan/tilt/zoom (P/T/Z) control receiver. Webthru SWC 306 can support up to six P/T/Z devices for six separate channels when Serial #2 (RS485 Half-
Duplex) is enabled. The Serial Port Base Address identifies each P/T/Z device to each channel. Select a channel to configure and change the Serial Port Base Address to correspond with the channel number. 10) Serial Port Configuration This page is to select a communication protocol among listed ones or to set control parameters manually for each serial port.
(1) Serial Port Selection Administrator selects a serial port to configure. Webthru SWC 306 has two serial ports. Serial #1 is a RS232C interface port, and Serial #2 is a RS485/RS422 interface port.
(2) Select Attached Device Administrator selects a communication protocol that an attached external device satisfies among already listed protocols. Samsung Techwin has listed protocols of Philips, Pelco (P and D), Sensormatic, Video Technical
(VTP 4x), LG (GAC-PT2), Sony (EVI-D3x), Surveyor (PT360 and TransitRCM), Sungjin (SJ3728R1), Kukjae (KRS-3200), Serim (SRP-PT1), Mitsubishi (CIT7300), and Samsung Techwin (SRX100B). Administrator may utilize any pan/tilt mechanism that satisfies already listed protocols. 29 Webthru SWC 306 Users Guide Audio Device This protocol is for Webthru Audio device, which is an audio transmission device connected to Webthru. 11) Digital I/O Configuration This page is to configure digital input state and control script. Webthru sends e-mails or/and files when connected external sensors detect events.
(1) Input Port 1, 2, 3, 4, 5, and 6 Administrator defines active state of 6 digital devices connected to six input ports such as infrared sensors. If normal open type device is connected to input port, select NO (Normally Open). With normal close type device, select NC (Normally Close).
(2) Output Port 1, 2, 3, 4, 5, and 6 Webthru shows current states of the 6 digital devices connected to 6 output ports. In the status panel, active state or de-active state message shows. De-
Active State means that connected device didnt detect any event when Apply button is clicked. Though this message is not updated until Apply button is clicked again, Webthru keeps on receiving status information from the connected device. 12) Alarm Configuration This page is to set image- recording conditions during an event situation for e-mail/FTP delivered images.
(1) Motion Detection Threshold Administrator sets the threshold for motion detection function. Threshold 0 is the most sensitive state and 900 is the least sensitive state.
(2) Alarm Parameters for E-mail /
FTP Application Administrator defines recording conditions for an event, if Webthru detects events through motion detection function (MD Event) or external devices (SID1, SID2, SID3, SID4, SID5 and SID6). image-
the 13) User Custom Configuration This page is to customize TCP ports of data transmission and default viewer composition. 30 Webthru SWC 306 Users Guide
(1) Web Server TCP Port Administrator assigns a web server TCP port for user access to Webthru and data transmission from Webthru. 80th port is assigned as default value.
(2) Video Server TCP Port Administrator assigns a video server TCP port transmission from Webthru. 8080th port is assigned as default value. image
(3) Select Main Page Administrator assigns a viewer for the main page of Webthru. Three viewing options are available: Single Viewer, Multi Viewer, and Server Push Viewer. Multi Viewer displays images through six-divided screens.
(4) Default Viewer Editing Default Viewer is designed for users to edit easily. Editable parts are as bellows. Main Title: It is to change the main title displayed at the bottom of the login page. Logo Image Source URL: Administrator may assign the URL of any web site from which default viewer gets a logo. Logo Image Link URL: Administrator may link the logo with a certain web page, such as a company or personal homepage. Background Color & Foreground Color: Ground color of default viewer can be changed. Administrator may set the color with RGB value. 14) Goto Viewer Page This menu is to return to real time image viewer page from administration page. 31 Webthru SWC 306 Users Guide Detailed Specifications of Webthru SWC 306 32bit RISC Embedded processor 8MB 16MB 64KB Embedded Linux NTSC or PAL video format are supported 6Ch. External Video Inputs 720X486, 720X243, 360X243, 180X121, 90X60 Wavelet 20:1 ~ 300:1 Max. 120fps (With 3KB image) Max. 30fps(NTSC) / 25 fps(PAL) (on 360X243) 2 ~ 30fps Decoding Rate Local Compression rate Max. 30fps/1Ch, 5fps/6Ch Security Password Based User Authentication IP-filtering (Secure Mode) Image Encryption Motion detection Sends e-mail automatically Sends the image files through FTP automatically Software-controlled 6-alarm input 6 Digital Input (Coupler), 6 Digital Output (Relay) High quality image area setting Image quality control (10 Levels) Periodic sending of images through E-Mail or FTP Gray/Progressive/Single-Shot/Channel Rotate Mode User customized home page publishing supported by FTP Audio supported through RS232 port DC 12V, 1.0A via external power supply
(Appendix 1) 1. General Hardware CPU Flash memory RAM ROM OS Video Channel Image Resolution Image Compression Algorithm Rate Performance Transfer Rate Alarms and I/O MISC. function Power Supply 2. Network Browser Connector Installation Protocols supported S/W Upgrade MS Internet Explorer V. 5.0 or higher JAVA Applet for non PC User (MAC or Unix) Two 10 Based-T Ethernet
(Network, Loop Stackable upto 3 boxes only with 1 IP) Assign IP address using setup program or ARP/RARP protocols TCP/IP, HTTP, ARP, RARP, ICMP, DHCP, FTP, SMTP, PPP and PPPoE Flash memory allows central remote software upgrades over network using FTP or private Webthru Upgrade program 32 Webthru SWC 306 Users Guide Management Configuration is achieved by private setup program and Web server built in administration page. 3. Mechanical Dimension Weight H x W x L = 45mm x 215mm x 252mm 1.45 kg (without power supply and accessories) 4. Compatible external devices and software PTZ control Sensor input RS-232, RS485/RS422 6 auxiliary inputs are supported, made of Opto coupler Opto coupler stands with 3-5V and 10-20mA 5. Environmental
(*) This data is a target specification. Operating Temperature 0 to 40 (32 to 104 ) Storage Temperature Relative Humidity Storage Humidity Power Source Environment
-20 to 60 (-4 to 104 ) 10 to 75%(There should be no condensation) 10 to 95%(There should be no condensation) D C 1 2 V 10% (External) Indoor 33 Webthru SWC 306 Users Guide
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2002-03-22 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2002-03-22
|
||||
1 | Applicant's complete, legal business name |
Hanwha Techwin Co., Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0020229910
|
||||
1 | Physical Address |
6, Pangyo-ro 319 Beon-gil, Bundang-gu
|
||||
1 |
Gyeonggi-do, N/A 13488
|
|||||
1 |
South Korea
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
j******@baclcorp.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
NLM
|
||||
1 | Equipment Product Code |
SWC306SERVER
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
J**** K******
|
||||
1 | Title |
Principal Research Engineer
|
||||
1 | Telephone Number |
82-70********
|
||||
1 | Fax Number |
82-31********
|
||||
1 |
j******@hanwha.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Web Server Camera | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bay Area Compliance Laboratory
|
||||
1 | Name |
J**** C******
|
||||
1 | Telephone Number |
408-7********
|
||||
1 | Fax Number |
408-7********
|
||||
1 |
b******@baclcorp.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC