HARMAN KARDON GO + PLAY WIRELESS Wireless portable hi-fi speaker for iPhone/iPod Owners Manual TM 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 1. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus. Only use attachments/accessories specified by the manu-
facturer. unused for long periods of time. apparatus combination to avoid injury from tip-over. specified by the manufacturer or sold with the apparatus. 12. Use only with the cart, stand, tripod, bracket or table When a cart is used, use caution when moving the cart 13. Unplug this apparatus during lightning storms or when 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as: when the power supply cord or plug has become damaged, when liquid has been spilled or objects have fallen into the apparatus, when the apparatus has been exposed to rain or moisture, when the apparatus does not operate normally, or the apparatus has been dropped. 15. Do not expose this apparatus to dripping or splashing and 16. To completely disconnect this apparatus from the AC ensure that no objects filled with liquids, such as vases, are placed on the apparatus. mains, disconnect the power supply cord plug from the AC receptacle. 17. The mains plug of the power supply cord shall remain 18. Do not expose batteries to excessive heat such as sun-
readily operable. shine, fire or the like. THE LIGHTNING FLASH WITH AN ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRE-
SENCE OF UNINSULATED "DANGEROUS VOLTAGE"
WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. SEE MARKING ON BACK OF PRODUCT. THE EXCLAMATION POINT WITHIN AN EQUILA-TER-
AL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE PRODUCT. Important Safety Instructions Fcc aNd ic REgulaTioNs (usa aNd caNada oNlY) Fcc aNd ic iNFoRMaTioN FoR usERs:
This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS 210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes (1) lappareil nedoit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est suscep-
tible den compromettre le fonctionnement. Rss-102 statement: This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment. Dclaration CNR-102: Cet quipement est conforme lexposition aux rayonnements Industry Canada limites tablies pour un environnement non contrl. nOTe: This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. cauTioN: ExPosuRE To Radio FREquENcY RadiaTioN To comply with FCC RF exposure compliance requirements, this device must not be co-located or operating in conjunction with any other antenna or transmitter. cauTioN: Changes or modifications not expressly approved in writing by HARMAN International may void the users authority to operate this equipment. Welcome Package Contents Carefully unpack your Harman Kardon Go + Play Wireless system and identify all components. iPhone/iPod Nest Power Supply
(AC cord varies with region) iPhone/iPod Adapter Kit HARMAN KARDON GO + PLAY WIRELESS Welcome Thank you for purchasing the Harman Kardon Go + Play Wireless portable hi-fi speaker for iPhone/iPod. This system has been designed to meet the highest audio-performance stan-
dards, and features HARMAN TrueStream, which guarantees peak wireless sound and clarity. The Harman Kardon Go + Play Wireless system will meet all your listening and travel needs, allowing you to immerse yourself in your favorite music wherever you are. Introduction The Harman Kardon Go + Play Wireless portable, high-fidelity docking system for iPhone/
iPod performs like a home theater system. With a groundbreaking design thats built for comfort, performance and freedom, the Harman Kardon Go + Play II unit will surround you with luxurious Harman Kardon sound when it is cradling your iPhone/iPod device or when youre wirelessly streaming audio to it via Bluetooth. Carry the unit by its stainless-steel arch handle to enjoy the ultimate portable soundstage. The system will provide clean, powerful sound for any music source connected to the Aux input and will even charge your iPhone/iPod while its docked.Enjoy the pinnacle of wireless audio performance with the Harman Kardon Go + Play Wireless system it will kick yourlistening experience into the future. Special Features IEQ Intelligent equalization technology tailors the performance of the Harman Kardon Go
+ Play Wireless microprocessor and digital signal processing (DSP) to optimize the systems output, based on battery or power-supply operation. Bi-amplification The Harman Kardon Go + Play Wireless unit uses two amplifiers to allow for clean, powerful sound output. Harman Kardon Go + Play Wireless Unit 3 HARMAN KARDON GO + PLAY WIRELESS General Setup 1. Unpack the Harman Kardon Go + Play Wireless system. 2. Place the nest into the docking station. 3. IMPORTANT: Turn the adjustable knob in the center of the docking station to properly sup-
port your specific iPhone/iPod model. 4. Place the iPhone/iPod device into the docking station. 5. Connect the power supply into the DC In jack. 6. Plug the adapter into the wall outlet. 7. If you prefer to use batteries, install eight (8) type D batteries into the bottom of the unit. 8. Press the Power button. The green LED will illuminate. General Setup Battery Installation 1. Unscrew the two battery-compartment cover screws counterclockwise to the unlocked position; remove the battery-compartment cover. 2. Place eight (8) fresh D-cell batteries as shown. 3. Replace the battery compartment cover. Note: System will not use battery power when using AC power. DC In USB S-Video Aux In Power Button
(Multi-Color LED) Volume Down Volume Up DO NOT MIX BATTERY TYPES. DO NOT MIX CHARGED AND PARTIALLY CHARGED BATTERIES. BATTERIES WILL NOT RECHARGE WHILE IN THE UNIT. Battery Disposal Alkaline batteries are considered nonhazardous. Rechargeable batteries (i.e., nickel cadmium, nickel metal-hydride, lithium and lithium-ion) are considered hazardous household materials and may pose an unnecessary health and safety risk. In the European Union and other locations, it is illegal to dispose of any battery with household trash. All batteries must be disposed of in an environmentally sound manner. Contact your lo-
cal waste-management officials for information regarding the environmentally sound collection, recycling and disposal of used batteries. 4 HARMAN KARDON GO + PLAY WIRELESS Listening to Audio from a Bluetooth-Capable Device 1. Press the Harman Kardon Go + Play Wirelesss Power button. The green LED will illuminate. 2. The Harman Kardon Go + Play Wireless unit will automatically enter the Bluetooth pairing mode. 3. Perform a new device search on your Bluetooth-capable device. 4. Select GO+PLAY WIRELESS on the devices pairing list. If the device asks for a passcode, enter 0000. 5. When pairing is successful the Harman Kardon Go + Play Wirelesss green LED will change to solid blue. 6. Control playback from your Bluetooth-capable device. To pair with a different device, press and hold the Power button until the LED turns green, then repeat steps 3 5 above. Listening to Music and Watching Videos and Photos from a docked iPhone/iPod 1. Dock your iPhone/iPod device in the nest and press the Harman Kardon Go + Play Wire-
lesss Power button. 2. To play music: Use the controls on your iPhone/iPod device to make selections and control the iPhone/iPod device and the Harman Kardon Go + Play Wireless. To play videos: Use a standard S-Video cable (not included) to connect the Harman Kardon Go + Play Wirelesss S-Video output to a compatible video-display device. Make sure that your iPhone/iPod devices Video and/or Photos functions are set to On. Use the controls on youriPhone/iPod device to make selections and control the iPhone/iPod and the Harman Kardon Go + Play Wireless. Bluetooth Pairing Listening to Music from an Auxiliary Device 1. Connect the auxiliary devices output into the Aux in jack by using a stereo 3.5mm (1/8 auxiliary cable (not supplied). 2. Press the Power button located on top of the Harman Kardon Go + Play Wireless system to turn on the unit. 3. Control music playback through the auxiliary device. 4. Adjust volume using the Volume Up (+) and Volume Down () buttons located on top of the unit. Charging Your iPhone/iPod 1. Make sure your iPhone/iPod device is securely docked in the Harman Kardon Go + Play Wireless unit by using the supplied nest. 2. Make sure that the Harman Kardon Go + Play Wireless unit is connected to a live electrical outlet. Note: The Harman Kardon Go + Play Wireless system will not charge other devices. 3. The Harman Kardon Go + Play Wireless unit will not charge an iPhone/iPod device while running on battery power. USB Synchronization and Charging The Harman Kardon Go + Play Wireless system features a USB synchronization and charge port. This allows you to synchronize a docked iPhone/iPod device with iTunes, and will charge a docked device even when the Harman Kardon Go + Play Wireless is operating on battery power. 3. Adjust volume using the Volume Up (+) and Volume Down () buttons located on top of 1. Connect the Harman Kardon Go + Play Wirelesss USB port to a computer using a USB cable the unit.
(not supplied). 2. Dock your iPhone/iPod device in the Harman Kardon Go + Play Wireless. 3. iTunes will synchronize with the iPhone/iPod device. 5 HARMAN KARDON GO + PLAY WIRELESS Troubleshooting Possible Problem Solution Note Symptom Troubleshooting Sound Quality There is no sound coming from the Harman Kardon Go +
Play Wireless unit. No power to unit. Sound comes from only one side/channel. iPhone/iPod device or auxiliary cable is not seated properly. Distortion (static, crackling or hissing sounds). Source device is distorting. Volume level may be too high from auxiliary-device output. EQ setting may be too high. Make sure that the wall outlet or power strip has power. Make sure that all switches for outlet/power strip are on and that all switches for the unit are on. If you are not using the AC adapter, make sure that fresh batteries are installed correctly. Make sure that the iPhone/iPod device is seated all the way into the docking station. Make sure that the auxiliary cable is seated all the way into the jack. Try resetting the iPhone/iPod device. Test the Harman Kardon Go + Play Wireless unit with another source. Check the volume of the source and turn it down if necessary. Check the EQ setting on your iPhone/iPod or source device. Is the green LED on? If the LED is not on, power is not getting to your HarmanKardon Go + Play Wireless unit. Try the solutions shown. If you are using a an Aux In cable, make sure it is a stereo cable. Does the distortion occur with specific songs? If so, check the recording or record the source again. Some devices will distort the signal if the volume is too high. It is recommended that you set the source device EQ to Flat or Off. Harman Kardon Go + Play Wireless unit emits a loud hum or buzzing noise. Aux In cable is not plugged in properly. Check the Aux In cable connection. Cable may be bad. Replace the cable. Speaker system experiences radio-frequency interference or picks up a radio-station transmission. Input cable may be picking up interference. Ground loop (an unsuitable connection). Sound does not appear to be coming from the grilles on the rear of the unit. Troubleshooting Charging iPhone/iPod device will not charge. One rear grille covers the bass reflex port, the other is to give the unit a symmetrical appearance. Turn the Harman Kardon Go + Play Wireless unit off and connect it to another wall outlet. Purchase a ferrite core and wrap the excess cable around it. A ferrite core can be purchased at your local electronics store. Make sure the front of the unit is facing forward while you are listening to it. No power to unit. The iPhone/iPod is not making full contact with the docking station. Make sure that your wall outlet or power strip has power. Make sure that all switches for outlet/power strip are on and that all switches for the unit are on. Make sure that the iPhone/iPod is seated securely into the docking station. The Harman Kardon Go + Play Wireless unit will not charge iPhone/iPod while running on battery power. 6 Technical Specifications HARMAN KARDON GO + PLAY WIRELESS Technical Specifications Model:
Harman Kardon Go + Play Wireless Optional batteries for unit:
8 type D alkaline batteries Drivers:
Power:
Two Ridge and two Hercules transducers Tweeters: 2 x 15 watts @ 1% THD Woofers: 2 x 30 watts @ 1% THD Frequency response:
40Hz 20kHz Input sensitivity:
250mV Dimensions:
Length: 20" (500mm) Width: 9" (230mm) Height: 9-1/2" (240mm) Weight:
Input impedance:
9.4 lb (4.3kg)
>10k ohms Signal-to-noise ratio:
>85dB External power supply Input voltage:
Output voltage:
100 240V AC 18VDC @ 3.3A 7