Product External Specifications For 802.1lac PCI Express Card Model Number : MRLBB-1403 Revision: 1.0 HP Contents 1.0 SCOPE... 1.1 DOCUMENT... 1.2 PRODUCT FEATURE!
2.0 REQUIREMENTS 2.1 RADIO CARD SPE 2.2 GENERAL SECTION 2.3 SOFTWARE REQUIREMENTS. 2.3.1 Security. 2.4 MECHANICAL REQUIREMENTS... ii 1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11ac PCI Express. This PCI Express card is based on QCA (Qualcomm Atheros) chip that complied with IEEE 802.1 lac from 5GHz, and it is also backward compatible to comply with IEEE 802.11a and IEEE 802.11n standard. 1.2 Product Features a) Dual band 802.11a / n/ ac radio i) 3 streams 3x3 MIMO ii) 5G operation iii) 1.3Gbps data rate b) Miniature RF connectors c) PCI express mini card form factor d) 5 to 40C operation e) ROHS complaint f) Low cost, highly integrated design 2.0 Requirements The following sections identify the detailed requirements of the 802.11ac PCI Express. 2.1 Radio Card Specifications Specification Description Frequency Range 4900-5845 MHz Actual operating frequencies depend on regulatory approval for the country of use. Wireless Medium Orthogonal Frequency Division Multiplexing 7
(OFDM), Spatial multiplexing (MIMO) Network Standards 802.112, 802.11n, 802.41ac ae |
Channel Bandwidth 20, 40, and 80 MHz - al Supported 3 (3x3 configuration) Also support 1 and 2 streams modes Data Rates Supported | go2.1 12: 6, 9, 12, 18, 24, 36, 48, and 54 Mbps 802.1 1n: MCSO up to MCS23 (450 Mbps). 802.11ac: NSS1-MCSO up to NSS3-MCS9 (1300 Mbps) Spatial Streams
| Maximum Available 5 GHz: 24.45 dBm oo Ean Actual transmit power may be limited by the country of operation, Transmit Power Control | 1dB step Operating Temperature 5Cto 40C Non-operating/Storage 40C to 70C Temperature 2.2 General Section
# Feature a Description 2.21 Antenna Connector | Three UFL compatible antenna connectors 278 T Operating Voltage [ 3.3VDC+/-5%
Pa Current = 5.1 W is use on continue TX Consumption 224 Form Factor and : Mini-card form factor with signal of PCI-e Gen! X1 lane Interface 2.3 Software Requirements The Configuration Software supports Linux driver. This configuration software includes the following functions:
Information Information allows you to monitor network status, Configuration Configuration allows you to configure parameters for wireless networking. e Security Supports enhanced security WEP, 802.1x, WPA and WPA2, 2.3.1 Security
# Feature Detailed Description 2.3.1.1 Encryption RC4 encryption algorithm
* Support 64-bit and 128-bit WEP encryption Support open system (OSA) and shared key authentication (SKA) 2312 WEP Management |* Four WEP keys can be selected
* STA with WEP off will never associate any AP with WEP enabled __WEP Key Format: Option for Hex format 23155. 802. 1x Support EAP-TLS, EAP-TTLS, and EAP-PEAP 2.3.1.4 WPA/WPA2 Support WPA/WPA2-PSK and WPA/WPA2-EAP Support Cipher Mode AES and TKIP 2.4 Mechanical Requirements The mechanical dimensions of the Mapletree radio card shall conform to the base PCI Express Mini Card Electromechanical Specification Revision 2.0 section 2.2.3 for Full Mini-card. FCC Statement:
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency nergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
e Reorient or relocate the receiving antenna.
@ Increase the separation between the equipment and receiver.
@ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
@ Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without C2P. This device is going fo be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only. IMPORTANT NOTE;
This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolied environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
B94MRLBB1403 . If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) I appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassessment permissive change. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. Dynamic Frequency Selection (DFS) for devices operating in the bands 5250-5350 MHz, 5470-5600 MHz and 5650-5725 MHz Slection dynamique de frquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 Mz, 5470-5600 MHz et 5650-5725 MHz The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation & lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. The maximum antenna gain permitted (for devices in the bands 5250-5350 MHz and 5470-5725 MHz) to comply with the e.i.r.p. limit. le gain maximal d'antenne permis pour les dispositifs utilisant les bandes 52505350 MHz et 5470-5725 MHz doit se conformer a la limite de p.i.r.e.;
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.-a-d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-
5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with |C RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avee un minimum de 20 cm de distance entre la source de rayonnement et votre corps. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has fo also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC : 466F-
MRLBB1403 ". This radio transmitter (identify the device by certification number, or model number if Category Il) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated, Antenna types not included in this. list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle s'il fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et V'impdance requise pour chaque type d'antenne, Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de I'metteur. Ant. Brand Part No, Antenna Type Connector Gain (city 1 M.gear | 1203000000954 | PCB Antenna LPEX 5.5 2 M. gear Tanaqo0ns096A | PCBAntenna | LPEX =H
(= M.gear | 1203000000068 | PCBAntenna | LPEX 68 Note: The EUT has three Antennas. Notice for Brazil, Aviso aos usu rios no Brasil Este equipamento opera em carater secundario, isto , nao tem direito a protecao contra interferncia prejudicial, mesmo de estagdes do mesmo tipo, endo pode causar interferncia a sistemas operando em carater primario. Notice for Korea Notice for Taiwan
{ey RN ER BRS RC ATU TORN + JERE + A] - RISERS hI EE - Ope ART Rohe EE ee aR A ide Oa TE cl 4 5.25-5.35 PoaaBANT NR (EZ AAT aT ELAS > ORS SEAN BERR 10