OEM Installation Guidance Document For HP SDGOB-1503 FCC ID: B94SDGOB1503; IC: 466D-SDGOB1503 Conditions on using HP regulatory approvals:
Customer must ensure that its product (the CUSTOMER Product) is electrically A. identical to Broadcoms reference designs. Customer acknowledges that any modifications to Broadcoms reference designs may invalidate regulatory approvals in relation to the CUSTOMER Product, or may necessitate notifications to the relevant regulatory authorities. Customer is responsible for ensuring that antennas used with the product are of B. the same type, with same or lower gains as approved and providing antenna reports to Broadcom. Customer is responsible for regression testing to accommodate changes to C. Broadcoms reference designs, new antennas, and portable RF exposure safety testing/approvals. The Broadcom radio is approved as a client/slave device; to ensure compliance with Appropriate labels must be affixed to the CUSTOMER Product that comply with D. applicable regulations in all respects. E. local regulations, the device should be set to the country domain in which the access point is installed. F. A users manual or instruction manual must be included with the customer product that contains the text as required by applicable law. Without limitation of the foregoing, an example
(for illustration purposes only) of possible text to include is set forth below:
1. USAFederal Communications Commission (FCC) FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the Page 1 of 8 OEM Installation Guidance Document For HP SDGOB-1503 FCC ID: B94SDGOB1503; IC: 466D-SDGOB1503 user is encouraged to try and correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. System integrators must include the FCC ID on the end product. FCC Radio-Frequency Exposure & Approval Conditions:
1. For Mobile applications, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-
located or operating in conjunction with any other antenna or transmitter. 2. Transmitting antenna(s) can only be installed at the display section of computer. When this device is installed other than notebook computers, at least 20 cm separation distance shall be maintained between the transmitting antenna(s) to the body of user or nearby person. 3. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter within a host device, except in accordance with FCC multi-transmitter product procedures. 4. Only those antennas with same type and lesser gain filed under this FCC ID number can be used with this device. 5. The regulatory label on the final system must include the statement: Contains FCC ID: B94SDGOB1503 or using electronic labeling method as documented in KDB 784748. 6. The final system integrator must ensure there is no instruction provided in the user manual or customer documentation indicating how to install or remove the transmitter module except such device has implemented two-ways authentication between module and the host system. 7. The final host manual shall include the following regulatory statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a Page 2 of 8 OEM Installation Guidance Document For HP SDGOB-1503 FCC ID: B94SDGOB1503; IC: 466D-SDGOB1503 particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Canada - Industry Canada (IC) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. French:
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Lutilisation de ce dispositif est autorise seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l utilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. French:
Sous la rglementation d'Industrie Canada, ce transmetteur radio ne peut fonctionner en utilisant une antenne d'un type et un maximum (ou moins) gain approuves pour l'metteur par Industrie Canada. Pour rduire le risque d'interfrence aux autres utilisateurs, le type d'antenne et son gain doivent tre choisis de manire que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est ncessaire pour une communication russie. Page 3 of 8 OEM Installation Guidance Document For HP SDGOB-1503 FCC ID: B94SDGOB1503; IC: 466D-SDGOB1503 This radio transmitter, IC ID: 466D-SDGOB1503, has been approved by Industry Canada to operate with the onboard antenna or a detachable WLAN antenna with a maximum gain listed below. The required antenna impedance is 50 ohms. French:
Cet metteur radio, IC ID: 466D-SDGOB1503, a t approuv par Industrie Canada pour fonctionner avec l'antenne intgre ou une antenne amovible PIFA avec un gain maximum de ci-dessous. L'impdance d'antenne requise est de 50 ohms. No. Antenna Manufacturer Antenna Type Model 1 HP 2 HP 3 Yageo/
Phicomp 802.11bgn WLAN Antenna 802.11bgn WLAN Antenna 802.11bgn WLAN Antenna Spectra antenna Peak gain
@ 2400-
2483.5MHz
(dBi) 2.5 Internal Reference Spectra trace antenna Ultra antenna 2.5 Ultra trace antenna ANTX300P002B24553 0.7 External antenna
(included in the EDU model FCC, IC, NCC approvals;
for EDS, the external antenna is covered by C1PC. Caution: Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Pour se conformer aux exigences de conformit 102 RSS RF exposition, pour des configurations mobiles, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil et toutes les personnes. Cet appareil ne doit pas tre co-
localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. System integrators must include a label with Contains IC: 466D-SDGOB1503 on the end product. Industry Canada user statements should be provided in both English and French, at the time each product is offered for sale or lease in Canada. Les intgrateurs de systmes doivent comporter une tiquette avec Contient IC: 466D-
SDGOB1503" sur le produit final. Comptes d'utilisateur d'Industrie Canada devraient tre Page 4 of 8 OEM Installation Guidance Document For HP SDGOB-1503 FCC ID: B94SDGOB1503; IC: 466D-SDGOB1503 fournis en anglais et en franais, au moment o chaque produit est offert la vente ou la location au Canada. 3. Europe - EU Restrictions This equipment needs to be marked with the European community. 2155 symbol and can be used throughout the Caution: Exposure to Radio Frequency Radiation. To comply with RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Czech:
User's Manual in Czech language and a statement of conformity with Directive 1999/5/EC in Czech language must be enclosed to each product. Italy:
For private use, a general authorisation is required if WAS/RLANs are used outside own premises. For public use, a general authorisation is required Note for system integrators:
- The module is tested to comply with the requirement of the R&TTE Directive. System integrators are responsible for compliance of the final device with the R&TTE Directive.
- Packaging: CE Marking must also be on the outer packaging of the product. The outer packaging must also provide an indication as to where the device is intended to be used and OR conversely, where there may be restrictions for use. 4. Taiwan - NCC Statement to be included in the user guide Statement- For general products Translation:
Page 5 of 8 OEM Installation Guidance Document For HP SDGOB-1503 FCC ID: B94SDGOB1503; IC: 466D-SDGOB1503 Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery. Article 14 The application of low power frequency electric machineries shall not affect the navigation safety nor interfere a legal communication, if an interference is found, the service will be suspended until improvement is made and the interference no longer exists. The foregoing legal communication refers to the wireless telecommunication operated according to the telecommunications laws and regulations. The low power frequency electric machinery should be able to tolerate the interference of the electric wave radiation electric machineries and equipments for legal communications or industrial and scientific applications. Appendix:
(ID):
CCXXxxLPyyyZz
,, CCXXxxLPyyyZz . 5. Korea Include the following statement either on the label or in the User Guide.
"
"
6. Argentina The current approval is in the name of Broadcoms local representative. It may be necessary to obtain regulatory approval in the name of the local distributor or importer. We suggest manufacturers check with their local distributors and importers in Argentina. 7. Brazil - Anatel Page 6 of 8 OEM Installation Guidance Document For HP SDGOB-1503 FCC ID: B94SDGOB1503; IC: 466D-SDGOB1503 Before using Broadcom Anatel approvals, 1. PC- OEM must make arrangement for its local offices or distributors to provide maintenance, technical assistance or replace any faulty products sold in Brazil. 2. All warranty services will be provided by the distributors or PC-OEM sales support in Brazil. An official agreement stating warranty responsibilities must be signed and made available to Broadcom. Interference statement to be included in the Users Guide
"Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio."
Translation:
"This equipment operates in secondary character. It can be affected by harmful interference. However, it cannot cause interference to systems operating in primary character."
8. South Africa ICASA PC-OEMs must make arrangement for importers to supply spare parts and carry out repairs in South Africa. 9. Indonesia POSTEL, Kenya CCK, Nepal - NTA PC-OEMs must make arrangement for importers to provide product warranty and after sales services. 10. Mexico PC-OEMs must make arrangement for importers to provide User Manual in Spanish in Mexico. The User Manual must feature the following mandatory statement:
La operacin de este equipo est sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia prejudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Translation:
The operation of this device is subject to the following two conditions:
(1) this equipment or device must not cause harmful interference and
(2) this equipment or device must accept any interference, including interference which could otherwise cause its undesired operation. Page 7 of 8 OEM Installation Guidance Document For HP SDGOB-1503 FCC ID: B94SDGOB1503; IC: 466D-SDGOB1503 12. CB Certifications PC-OEMs must provide User Guides in the language suitable for the countries when shipping products to countries listed in the CB reports. 13. Moldova- Labeling to be included Proper Marking must be included on each certified unit shipping into Moldova, Page 8 of 8