FCC ID: B94SDGOB1392 802.11bgn 1x1 SDIO Module

Introduction: 802.11b/g/n WLAN Module, SDGOB-1392 User's Guide Before you begin Things you should know SDGOB-1392 network Before you begin Obtain the following information from your network administrator (if you are a home user, obtain this information from the person that installed your wireless access point):

l Network names (SSID) of the specific wireless networks that you want to connect to. l WEP (Wired Equivalent Privacy) key information (if any) for the networks you want to connect to. l For Microsoft Windows networking, your customer name and workgroup name. l For your network account, your user name and password. l Your IP address (if not using a DHCP server) Things you should know When you start your computer, your SDGOB-1392 card detects certain wireless networks that are within range. Before you can connect to these and other wireless networks, you must configure a profile for each network using the information you obtained from your network administrator. WEP is a security protocol for wireless local area networks (defined in the IEEE 802.11g standard) that encrypts data sent over radio waves. The use of the WEP key is optional and can be enabled or disabled. If the network you are connecting to has enabled WEP, you must also enable WEP in the network profile and set the WEP key to match the WEP key used by the network. Otherwise, you cannot connect to the network. Broadcom SDGOB-1392 network The SDGOB-1392 card solution allows you to make a wireless connection to a network, as illustrated below. Back to top Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Back to Contents Page Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Overview Utility Components Overview The Broadcom Wireless Utility enables you to do the following network tasks:

l Manage your wireless networks and create network connection profiles (Wireless Networks tab) l Connect to available networks (utility icon in notification area) l Get information about the network status and signal and noise of your network connection (Link Status tab) l View current and accumulated statistics (Statistics tab) l Find out which broadcasting networks are in range and search for nonbroadcasting networks (Site Monitor tab) l Run tests on the wireless network adapter (Diagnostics tab) l Get date and version information about the utility, and software, hardware, and location details about your wireless network adapter (Information tab) l Manually add or delete trusted servers and enable the manual acceptance or rejection of auto-

provisioning and A-ID group changes (Wireless Networks tab) l Manually import EAP-FAST PACs (Wireless Networks tab) In the utility, you can open Wireless Network Wizard to connect to a basic network or create an ad hoc network, or you can open the Wireless Network Connection Settings tool to connect to an advanced network. To do any of the other tasks, click the tab that is associated with the described task. To start using the utility, right-click the utility icon If the icon is not available, open Broadcom Wireless Utility in Control Panel. in the notification area, and then click Open Utility. NOTE: The utility icon may not appear exactly as shown here. See "Table 1. Signal Strength Indicated by the Broadcom Wireless Utility Icon."

Utility Components Utility components include the utility icon in the notification area, the six utility tabs, and Wireless Network Connection Settings. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (1 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Utility Icon To do any of the following tasks or operations, right-click the utility icon, and then click the appropriate item. l Open the on-line Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide

(Help Files) l Open About WLAN Card Utility to view links to Broadcom and Broadcom Customer Support websites and to view the version and date of the utility (About) l Hide the utility icon (Hide Tray Icon) l Disable or enable the radio (Disable/Enable Radio) l Connect to any of the networks for which you have created a connection profile and are within range (Connect To) l Open the utility to the Wireless Networks tab (Open Utility) l Open the utility to the Link Status tab to view information about the connection (Status) l Display a log of your wireless network events (Display Log) Wireless Networks Tab The Wireless Networks tab has tools that enable you to do the following:

l Use the utility to manage your wireless networks l Add a network connection profile l Edit or remove a network connection profile l Change the order in which profiles are listed under Preferred network connections l Connect to any listed network without changing its order in the list l Disable or enable the radio (Disable/Enable Radio) l Show or hide the utility icon in the notification area l Choose which type of network to access l Lock or unlock a preferred network connection profile l Save your wireless network connection profiles as a WPN file l Import a WPN file l Manually add or delete trusted servers and enable the manual acceptance or rejection of auto-

provisioning and A-ID group changes l Manually import EAP-FAST PACS On the Add menu, you can use either the wireless network wizard that is available from Broadcom Wireless Utility (see Connecting to a Basic Network or Creating an Ad Hoc Network Using the Wireless Network Wizard") or the utility (see "Connecting to an Advanced Network Using the Broadcom Wireless Utility") to add a network connection profile. To use the utility to manage your wireless networks, select the Let this tool manage your wireless networks check box. To add a network connection profile, click the Add arrow, and then click either Use Wizard (basic network) or Use Utility (advanced network). To edit or remove a network connection profile, right-click the network name, and then click either Edit or Remove. To change the order in which profiles are listed under Preferred network connections, click the network name, and then click either the up arrow or down arrow. To connect to any listed network without changing its order in the list, right-click the network name, and then click Connect. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (2 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide To disable the radio, clear the Enable radio check box. To enable the radio, select the Enable radio check box. To hide the utility icon utility icon check box.

, clear the Show utility icon check box. To show the icon, select the Show To choose the type of network to access, click the Options arrow, and then click Advanced. To lock or unlock a preferred network connection profile, right-click anywhere in the row that lists the network name, and then click Lock or Unlock, as appropriate. NOTE: You must have system or administrator rights to be able to lock or unlock a profile. To save your wireless network connection profiles to a WPN file, click the Options arrow, and then click Export (see "Saving Preferred Network Connection Settings to a File" in "Connecting to an Advanced Network Using the Broadcom Wireless Utility."

To import a WPN file, click the Options arrow, and then click Import (see "Importing a Preferred Network Connection Profiles File" in "Connecting to an Advanced Network Using the Broadcom Wireless Utility."

Click Apply or OK after you change any of the settings for the change to take effect. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (3 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide For networks that use the EAP-FAST authentication method, the Wireless WLAN Card Utility automatically adds trusted servers to the trust list and accepts auto-provisioning and AID (A-ID) group changes by default. The utility also enables you to import a Protected Access Credential (PAC). From the utility, you can also manually add or delete trusted servers, enable the manual acceptance or rejection of auto-

provisioning and A-ID group changes, or import or delete PACS, as described in the following instructions. In general, you should use the default settings. Therefore, check with the network administrator before you make any changes. To manually add a trusted server to the trust list 1. Open Broadcom Wireless Utility. 2. From the Wireless Networks tab, click Options, point to Cisco Compatible Extensions, and then click Administrator Settings. 3. Click Add. 4. Type the A-ID friendly name of the trusted server in the space provided, and then click OK. To delete a trusted server from the trust list file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (4 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide 1. Open Broadcom Wireless Utility. 2. From the Wireless Networks tab, click Options, point to Cisco Compatible Extensions, and then click Administrator Settings. 3. In the Trust list (A-ID), click the name of the trusted server you want to delete, and then click Delete. To change the default settings for administering Cisco Compatible Extensions 1. Open Broadcom Wireless Utility. 2. From the Wireless Networks tab, click Options, point to Cisco Compatible Extensions, and then click Administrator Settings. 3. Clear the Disable auto-provision prompt check box to enable manual acceptance or rejection. 4. Clear the Disable A-ID group change prompt check box to enable manual acceptance or 5. Select the Auto-provision PAC only once check box to auto-provision a Protected Access rejection. Credential (PAC) only once. To import or remove an EAP-FAST PAC 1. Open Broadcom Wireless Utility. 2. From the Wireless Networks tab, click Options, point to Cisco Compatible Extensions, and 3. To import a PAC: in Protected Access Credentials, click Add, and then follow the on-screen then click Manage PACs. instructions. NOTE: The PAC is password protected, so you must know the password to be able to import the PAC.

-or-

To remove a PAC: click anywhere in the row that lists the PAC, and then click Remove. Link Status Network status and signal and noise information about your network connection is displayed on the Link Status tab. NOTES:

l For IEEE 802.11n connections, speed is indicated by an MCS value. l Radio Stream information is provided only for IEEE 802.11n connections. l Click anywhere in the Signal & noise history box to change the type of history being displayed. Successive clicks change the type from both signal and noise, to noise only, to signal only, and back to both signal and noise. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (5 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide The status of your network connection is also indicated by the appearance of the utility icon number and color of the radio waves indicates the strength or weakness of the signal (see Table 1. Signal Strength Indicated by the Broadcom Wireless Utility Icon for details). The To view the network name (SSID), speed, signal strength rating, connection status, and the client IP address of the network connection, move your mouse pointer over the utility icon. NOTE: On computers running Windows XP, you also can view the SSID, speed, signal strength rating, and connection status by moving your mouse pointer over the Windows Wireless Network Connection icon in the notification area. Table 1. Signal Strength Indicated by the Broadcom Wireless Utility Icon file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (6 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Icon Appearance Indicated Received Signal Strength The signal strength is very good or excellent. The signal strength is weak. See Troubleshooting for suggested action. No signal is being received. See Troubleshooting for probable causes and suggested action. The radio is disabled or switched off. See Troubleshooting for suggested action. Statistics On the Statistics tab under Current, the following current statistics are shown:

l Network name (SSID) l Connection time l Packets sent l Packets received l Sent packets lost l Received packets lost l Total packets lost (%) Under Accumulated, the following accumulated statistics are shown:

l Packets sent l Packets received l Sent packets lost l Received packets lost file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (7 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Site Monitor Basic Site Monitor On the Site Monitor tab, the basic Site Monitor displays information about wireless routers/APs and ad hoc networks that are within range. To sort the list, click the column heading that shows the characteristic you want to sort by. For example, to sort by signal strength, click Signal . To view information about a particular wireless router/AP or ad hoc network, click anywhere in the row that lists the wireless router/AP or ad hoc network. The network information is shown under Selected Network. To view or change the network connection settings for a particular wireless router/AP or ad hoc network, right-click anywhere in the row that lists the wireless router/AP or ad hoc network, and then click Editif you have not yet created a network connection profile for that particular wireless router/AP or ad hoc network and want to do so, click Add . To see the information elements for a listed AP or ad hoc network, right-click anywhere in the row that lists the AP or ad hoc network, and then click Show Information Elements. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (8 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide NOTES:

l Nonbroadcasting networks are labeled (nonbroadcasting) under Network Name. l The network performance may be degraded while Site Monitor is displaying nonbroadcasting APs to which you are not currently connected. l The symbols under AP Band indicate IEEE 802.11b, IEEE 802.11g, or IEEE 802.11n operation. To see more detailed information about a particular wireless router/AP or ad hoc network, click anywhere in the row that lists the wireless router/AP or ad hoc network, and then click Advanced. Advanced Site Monitor To save the activity log to a file, click the Options arrow, and then click Start Log. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (9 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide You can adjust the time interval between scans by clicking the Options arrow, and then clicking either one of the preset values or clicking Customize to specify a different time interval. NOTE: The network performance may be degraded while Site Monitor is displaying nonbroadcasting networks to which you are not currently connected. To view detailed network information for a single nonbroadcasting network, type the network name in the Look for box, and then click Find. To reset the site monitor to the broadcasting networks, click Clear. Diagnostics On the Diagnostics tab, you can run a number of tests to determine if your wireless network adapter is functioning properly. Select the tests you want to run, and then click Run. For information about an individual test, look under Information before you click Run. To see the test results, look under Information after you click Run. NOTE: The network connection is lost when you run the tests. When the test run is over, your network connection is automatically reestablished. Also, you can view a log of your wireless network events. To do so, click Log. Examples of wireless network events that are logged include:

file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (10 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide l Initiation of user session l Connecting to a network l Disconnecting from current network l Authentication mode being used l Driver status l Supplicant status l New wireless device available l Initializing wireless state machine l Wireless utility is managing this adapter l Wireless utility is not managing this adapter If your Broadcom 802.11 Network Adapter fails any of the diagnostics tests, go to http://www.broadcom. com/ for technical support. Information file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (11 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide The following information is displayed on the Information tab:

l Software details l Hardware details l Location details (shows the country for which the driver is installed and the channels supported for that location) Wireless Network Connection Settings The Wireless Network Connection Settings component is intended for use by advanced users or network administrators. You can use Wireless Network Connection Settings to create a connection profile for an advanced infrastructure network, a basic infrastructure network, or an ad hoc network (see " Connecting to an Advanced Network Using the Broadcom Wireless Utility"). Back to Contents Page file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (12 of 12)4/25/2006 1:57:41 PM Regulatory Statements for SDGOB-1392 USA-Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the distance between the equipment and the receiver.

-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Caution: Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Canada Industry Canada (IC) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. L utilisation de ce dispositif est autorise seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l utilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. Caution: Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. This device has been designed to operate with the antennas listed below, and having a maximum gain of 2.5 dBi @ 2.4GHz. Antennas not included in this list or having a gain greater than 2.5 dBi @ 2.4GHz are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. EuropeEU Declaration of Conformity and Restrictions Hereby, Broadcom Corp, declares that this equipment complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. 0984 symbol and can be used throughout the This equipment is marked with the European community. This indicates compliance with the R&TTE Directive 1999/5/EC and meets the relevant parts of following technical specifications:

EN 300 328 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission Systems; Data transmission equipment operating in the 2,4GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE directive. EN 301 489-17 - Electromagnetic Compatibility and Radio Spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 17 Specific Conditions for Wideband Data and HIPERLAN Equipment. EN 60950 - Safety of Information Technology Equipment. EN 62311 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0Hz - 300 GHz). Marking by the symbol indicates that usage restrictions apply. France - 2.4GHz for Metropolitan France :

In all Metropolitan dpartements, wireless LAN frequencies can be used under the following conditions, either for public or private use:

Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz frequency band Outdoor use: maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and with maximum power (EIRP*) of 10 mW for the 2454-2483 MHz band Caution: Exposure to Radio Frequency Radiation. To comply with RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Taiwan NCC warning statement Appendix:

(ID):

CCXXxxLPyyyZz

,, CCXXxxLPyyyZz .

Inkjet Consumer Solutions (ICS) Division 16399 West Bernardo Drive San Diego CA 92127-1899, USA _______________________________________________________________ GENERAL DECLARATION 802.11 b/g/n WLAN Module SDGOB-1392 B94SDGOB1392 We, Hewlett Packard Company, declares that the device does not have Ad Hoc on non-US frequencies and/or on DFS frequencies while applying for the following product. The device operates on Ch1-11 in the US. Model Name:

Model Number:

FCC ID:

If you have any questions regarding the declaration, please dont hesitate to contact us. Thank you!

Sincerely yours, 26 August, 2013 Date Bansi R. Patel Product Regulations Engineer 858-655-3593 (tel) 858-655-3346 (fax) bansi.patel@hp.com

Authorization on Behalf of Hewlett-Packard Company For the US Federal Communications Commission Office of Engineering and Technology and Other FCC Programs and Offices 1. I, David P. Adams, am Canada/USA Technical Regulations Manager for Hewlett-Packard Company (Hewlett-Packard) and Applicant/Grantee Contact of Record for Hewlett-Packard together with its subsidiaries and affiliates worldwide (collectively, HP) for HPs dealings with the United States Federal Communications Commission (FCC). I am duly authorized by HP to make this Authorization on HPs behalf. 2. This Authorization will designate the person named below to act on my behalf and HPs behalf as authorized agent and representative, until further notice, with the additional power to designate one or more third party agents for HP with regard to particular matters and applications. All acts carried out and requests made by this named representative relating to any matter before the FCC, including requests for confidentiality, shall have the same effect as mine. Name:

Title:

Address:

Telephone:

E-mail:

Bansi R. Patel Product Regulations Engineer Attention: Bansi R. Patel Mail stop 65-220 Hewlett-Packard Company 16399 West Bernardo Drive San Diego, CA 92127-1889 858-655-3593 bansi.patel@hp.com 3. Questions about the scope and effect of this Authorization should be addressed David P. Adams Canada/USA Region Technical Regulations Manager 1501 Page Mill Road, MS 1419 Palo Alto, CA 94304-1126 650.857.4423 Telephone 650.362.6534 Fax dadams@hp.com as follows:

4. I declare under penalty of perjury that the foregoing is true and correct, and that this Authorization was executed at Palo Alto, California, on the date indicated below my signature. David P. Adams Canada/USA Technical Regulations Manager Hewlett-Packard Company __July 16, 2013__________________________ Date ____________________________ Signature

Applicant/Grantee Hewlett- Packard B94SDGOB1392 FCC ID:

Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Section 15.212 Modular Transmitters Single Modular Approval Requirements Refer to external photos. Shield is over the radio circuit module. Y All inputs to the modules are buffered through logic or microprocessor inputs. Refer to Schematics. Internal 3.3V power regulator. Refer to schematics. Module contains a hirose connector. The module will go inside final product where the antenna(s) will be integral to the end product, which can be considered permanently attached. Y Y Y Module was tested outside. Refer to test setup photos in test report. Y 1 2 3 4 5 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting 6 Refer to label provided. Y equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available

(see Section 15.31(i)). The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID:

XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. 7 Refer to manual Y 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Refer to MPE calculation in the Test report Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.