Product External Specifications For 802.11n PCI Express Card Model Number : MRLBB-1402 Revision: 1.0 HP Contents 1.0 SCOPE... 1.1 DOCUMENT 1.2 PRODUCT FEATURES 2.0 REQUIREMENTS 2.1 RADIO CARD SPECIFICATION 2.2. GENERAL SECTION... 2.3 SOFTWARE REQUIREMENTS. 2.3.1 Security........ 2.4 MECHANICAL REQUIREMENTS .. 1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11n PCI Express. This PCI Express card is based on QCA (Qualcomm Atheros) chip that complied with IEEE 802.1 1a from SGHz, and it is also backward compatible to comply with IEEE 802.11b and IEEE 802.1 1g standard. 1.2 Product Features a) Dual band 802.11b/g/nradio i) 3streams 3x3 MIMO ii) 2.4 operation b) Miniature RF connectors c) PCl express mini card form factor d) 5 to 40C operation e) ROHS complaint f) Low cost, highly integrated design 2.0 Requirements The following sections identify the detailed requirements of the 802.11n PCI Express. 2.1 Radio Card Specifications Specification Description Frequency Range 2400-2500 MHz Actual operating frequencies depend on regulatory approval for the country of use. Wireless Medium Direct Sequence Spread Spectrum (DSSS), Orthogonal Frequency Division Multiplexing
(OFDM), Spatial multiplexing (MIMO) Network Standards 802.11b, 802.119, 802.11n Channel Bandwidth 20, 40MHz Supported Spatial Streams 3 (3x3 configuration) Also support 1 and 2 streams modes Data Rates Supported 802,11b: 1, 2, 5.5, 11 Mbps 802.119: 1, 2, 5.5, 11,6, 9, 12, 18, 24, 36, 48, and 54 Mbps 802.11n: MCSO up to MCS23 (450 Mbps) Maximum Available 2.4 GHz: 27.10 dBm Conducted Transmit Actual transmit power may be limited by the Power country of operation. Transmit Power Control | 1dB step Operating Temperature 5Cto 40C. Non-operating/Storage -40C to 70C. Temperature 2.2 General Section i at Dealslierition a 2.2.1 Antenna Connector | * Three UFL compatible antenna connectors 2.2.2 Operating Voltage | * 3.3VDC +/- 5%
22.3 Current = 5.1W is use on continue TX Consumption 2.24 Form Factor and Mini-card form factor with signal of PCI-e Gen! X1 lane Interface 2.3 Software Requirements The Configuration Software supports Linux driver. This configuration software includes the following functions:
* Information Information allows you to monitor network status.
* Configuration Configuration allows you to configure parameters for wireless networking. Security Supports enhanced security WEP, 802.1x, WPA and WPA2. 2.3.1 Security
23:11 Encryption * RC4 encryption algorithm
* Support 64-bit and 128-bit WEP encryption
* Support open system (OSA) and shared key authentication (SKA) 2.3.1.2 WEP Management |* Four WEP keys can be selected STA with WEP off will never associate any AP with WEP enabled
* WEP Key Format: Option for Hex format 23.1.3 802.1x
~ Support EAP-TLS, EAP-TTLS, and EAP-PEAP 2.3.14 WPA/WPA2 Support WPA/WPA2-PSK and WPA/WPA2-EAP Support Cipher Mode AES and TKIP 2.4 Mechanical Requirements The mechanical dimensions of the Mapletree radio card shall conform to the base PCI Express Mini Card Electromechanical Specification Revision 2.0 section 2.2.3 for Full Mini-card. FCC Statement:
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
e Reorient or relocate the receiving antenna. e Increase the separation between the equipment and receiver. e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. e Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without C2P. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
B94MRLBB1402 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux Etats-Unis / Canada du march, seul le canal I a 11 peuvent tre exploits, Slection d'autres canaux n'est pas possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassessment permissive change. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC : 466F-
MRLBB1402 ". This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modele s'il fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Table for Filed Antenna Part Number Wee 1 M.gear 1203000000974 PCB Antenna 2 M.gear 1203000000974 | PCB Antenna 3 M.gear 120300000097A | PCB Antenna Note: The EUT has three antennas (3TX, 3RX). Notice for Brazil, Aviso aos usuarios no Brasil Este equipamento opera em carater secundario, isto 6, ndo tem direito a proteao contra interferncia prejudicial, mesmo de estagdes do mesmo tipo, endo pode causar interferncia a sistemas operando em carater primario. Notice for Korea Aw AeA UE Bit AAC D717 AIS Dit) 22 ee ee
(A8S COMIN) fe iia 22 Pt eee eo sa a4 Att4 48G 9 URUG This dovice obtained EMC reg sition meniy for home ve
{Glas Bland may be vse if area Cats 8 (Broadsatting Communication vice for Home Ue) 24 FAURE A Hegel ow 2 clue at ee AG & O aie Notice for Taiwan ASD PAA PE
+I MORSE Ste RN + SESMPO] + 2.5] - AERO ALIS RRS ROAR - DOL ERTS Bohs iE a Eee eee age HE 5.25-5.35 PaO PREZ RR EET SM RRA + MESSE PS EF 10