FCC ID: B94TNM101D Embedded HyperX Wireless Module

SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. TPN-M101D Page 1 of 19 Marketing Name. Integrated Dongle Revision 03 REVISION AND UPDATES REV ECN NO. DESCRIPTION DATE BY 00 01 N/A N/A 1. First Release (EVT) 2022/03/10 Vincent Tung 1. Update Block Diagram in item 3.1. 2022/04/13 Vincent Tung 2. Update PID and product string info in 2022/05/19 Thum Keng How item 5.2. 3. Update Regulatory requirement &

Selling countries in item 9. 2022/05/19 Leon Lee 4. Update Package specification in item 2022/05/19 Qincao.Li 12. 5. Update module layout guidelines in item 2022/05/19 Vincent Tung 11. 02 N/A 1. Updata Figure 3.4-1 Dimensions and 2022/07/06 Vincent Tung board assembly. 2. Updata Figure 3.5-1 Module footprint for assembly on a carrier board. 3. Update item 6.1 Shielded case drawing. 4. Update item 6.3 PCBA Dimensions drawing. 5. Update item 9 Certificate test plan. 6. Add item 11.2 Package Moisture Sensitivity Level. 7. DVT1 Version release. 03 N/A 1. Change Bluetooth version 5.2 to 5.3 in 2022/09/27 Vincent Tung item 2.6. 2. Updata Figure 3.4-1 Dimensions and board assembly. 3. Updata Figure 3.5-1 Module footprint for assembly on a carrier board. 4. Update item 6.3 PCBA Dimensions drawing. 5. Updata Figure 10.5-1 Top View (Unit :

mm)Recommended solder pad layout. 6. DVT2 Version release. The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. TPN-M101D Page 2 of 19 Marketing Name. Integrated Dongle Revision 03 Customers Product Specification Customer: A27 PRODUCT NAME: ULL Module MODEL NO: Ralphie PART NO:

REV.: 00 FCC 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. TPN-M101D Page 3 of 19 Marketing Name. Integrated Dongle Revision 03 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment."

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. IC

"This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement."

The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. TPN-M101D Page 4 of 19 Marketing Name. Integrated Dongle Revision 03

"Caution: Exposure to Radio Frequency Radiation 1. To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter."

2. To comply with RSS 102 RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.

"Attention: exposition au rayonnement radiofrquence 1. Pour se conformer aux exigences de conformit RF canadienne l'exposition, cet appareil et son antenne ne doivent pas tre co-localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur."

2. Pour se conformer aux exigences de conformit CNR 102 RF exposition, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil et toutes les personnes Required End Product Labeling Any device incorporating this module must include an external, visible, permanent marking or label which states:

Contains FCC ID: B94TNM101D and Contains IC :466X-TNM101D Obligation d'tiquetage du produit final:

Tout dispositif intgrant ce module doit comporter un externe, visible, marquage permanent ou une tiquette qui dit: "Contient IC : 466X-TNM101D Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. FCC This module has been tested and found to comply with the following requirements for Modular Approval. Part 15.247 - Operation within the bands 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz. The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. TPN-M101D Page 5 of 19 Marketing Name. Integrated Dongle Revision 03 Test Modes This device uses various test mode programs for test set up which operate separate from production firmware. Host integrators should contact the grantee for assistance with test modes needed for module/host compliance test requirements. Antennas This radio transmitter has been approved by the FCC and ISED to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antennes Cet metteur radio a t approuv par la FCC et ISED pour fonctionner avec les types d'antennes rpertoris ci-dessous avec le gain maximal autoris indiqu. Les types d'antennes non inclus dans cette liste, ayant un gain suprieur au gain maximum indiqu pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Radio Antenna Type Bluetooth Bluetooth Bluetooth Bluetooth Bluetooth PIFA PIFA PIFA PIFA PIFA Freq.

(MHz) 2402-2480 2402-2480 2402-2480 2402-2480 2402-2480 Max. Peak Antenna Gain (dBi) 3.41 2.73

-0.65 2.43 0.97 The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as shown in User manual. In the end product, the antenna(s) used with this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operation in conjunction with any other antenna or transmitter except in accordance with FCC multi-

transmitter product procedures. User and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying the RF exposure compliance. The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. TPN-M101D Page 6 of 19 Marketing Name. Integrated Dongle Revision 03 NCC NCC LP0002 _ 3.8.2 JP FCC ID of this device is FCC ID:B94TNM101D ISED Model and certificate number of this device is TPN-M101D and IC:466X-TNM101D The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. TPN-M101D Page 7 of 19 Marketing Name. Integrated Dongle Revision 03 Contents 1 General Product Specification for device ..................................................................... 8 1.1 Product part number list Merry ........................................................................................................... 8 2 Features ........................................................................................................................... 9 2.1 2.2 2.3 2.4 2.5 2.6 Host processor subsystem .................................................................................................................... 9 DSP processor subsystem ..................................................................................................................... 9 Memory summary .................................................................................................................................... 9 Platform ..................................................................................................................................................10 Peripheral ...............................................................................................................................................10 Connectivity (Bluetooth) features overview .......................................................................................10 2.6.1 Bluetooth RF ..........................................................................................................................................10 2.6.2 Bluetooth baseband ..............................................................................................................................11 2.6.3 Power management unit (PMU) features overview ............................................................................11 2.7 Compact size with .................................................................................................................................11 3 Firmware Specification ................................................................................................. 12 3.1 3.2 Feature/Description ...............................................................................................................................12 USB Interface .........................................................................................................................................13 4 Mechanical ..................................................................................................................... 14 4.1 4.2 Shielded case drawing ..........................................................................................................................14 Antenna connector detail .....................................................................................................................15 4.3 PCBA Dimensions drawing .....................................................................................................................16 5 Package Specification ................................................................................................... 17 The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. TPN-M101D Page 8 of 19 Marketing Name. Integrated Dongle Revision 03 1 GENERAL PRODUCT SPECIFICATION FOR DEVICE 1.1 Product part number list Merry ITEM MODEL NO. PART NO. SHIP PLACE TYPE 1 MX-121-001-01 89M121001001 The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. TPN-M101D Page 9 of 19 Marketing Name. Integrated Dongle Revision 03 2 FEATURES 2.1 Host processor subsystem ARM Cortex-M4 (CM4) with Floating Point Unit (FPU) application processor Supports Memory Protection Unit (MPU) Supports Nested Vectored Interrupt Controller (NVIC) with 41 interrupt sources each with up to 16 levels of priority. Support Serial Wire Debug (SWD, 2 pins) and JTAG (5 pins) debug interface. Support breakpoints, watchpoints, stepping, vector catching, data matching. Complete debug features. Maximum speed: 208MHz 192kB memory with zero wait state. It can be programmed as L1 cache or Tightly Couple Memory (TCM). Configurable L1 cache size: 32kB, 16kB, 8kB or 0kB eXecute In Place (XIP) on flash memory DSP processor 2.2 DSP processor subsystem Cadence HiFi MiniAudio Engine DSP coprocessor with HiFi EP extension 7-stage pipeline Maximum speed: 416MHz Support Memory Management Unit (MMU) for memory protection with translation 32 maskable interrupts with 4 priority levels and a NMI (non-maskable Interrupt) 16kB instruction cache and 16kB data cache with high hit rate and zero wait state 192kB instruction RAM with zero wait state 512kB data RAM with zero wait state and two memory banks to increase co-access performance. 2.3 Memory summary On-die memories (SRAMs) with up to 192kB at CPU clock speed with zero wait state. Low latency 400kB system RAM (SYSRAM) with maximum speed 208MHz System in Package (SiP) 32Mb low-power flash memory with 0.1A deep-down current

(typical condition) and maximum speed 104MHz The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Model No. Page TPN-M101D 10 of 19 Prepared by:

Approved by:

Merry Team Merry Team Marketing Name. Integrated Dongle Revision 03 2.4 Platform Dynamic Frequency Scaling (DFS) 30 DMA channels RTC timer Nine general purpose timers (GPT s) Watchdog timer (WDT) Crypto engine for AES/SHA1/SHA224/SHA256 True random number generator Ambient temperature from -40C to 85C 2.5 Peripheral One USB2.0 device One MSDC (eMMC4.41 / SDIO v2.0) up to 48MHz Three I2C interfaces up to 3.4Mhz Three UART interfaces up to 3Mbps SPI master interfaces up to 52MHz ESC external sram control interface up to 52MHz One SPI slave interface up to 52MHz PWM channels 12-bit AUXADC channels 2.6 Connectivity (Bluetooth) features overview ULL Module offers a highly integrated Bluetooth radio and baseband processor. ULL Module is fully compliant with Bluetooth version 5.3. It is upgradable to later versions, including BR/EDR and Bluetooth LE1M/2M and offers enhanced data rates of up to 3Mbps. 2.6.1 Bluetooth RF Fully compliant with Bluetooth core specification 5.3. Low-IF architecture with high degree of linearity and high order channel filter. Integrated T/R switch and balun. Hardware AGC dynamically adjusts the receiver performance in changing environments. The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Prepared by:

Approved by:

Merry Team Merry Team Model No. Page TPN-M101D 11 of 19 Marketing Name. Integrated Dongle Revision 03 2.6.2 Bluetooth baseband Bluetooth specification V5.3 + dual mode + isochronous channel Up to four simultaneous active ACL links. Up to four simultaneous active Bluetooth LE links. Support for single SCO or eSCO link with CVSD/mSBC coding. Support for BLE1M/2M Up to simultaneous active ICO/ICL links (ICO+ICL links=4) AFH and PTA collaborative support for WLAN/Bluetooth coexistence. Supports PCM interface and built-in programmable transcoders for linear voice with re-transmission. Built-in hardware modem engine for access code correlation, header error correction, forward error correction, CRC, whitening and encryption. Channel quality driven data rate adaptation. Channel assessment for AFH. 2.6.3 Power management unit (PMU) features overview Input range: 4.5V ~ 5.5V Low quiescent buck converters and LDOs. Ultra-low quiescent current with regulators. Over-current and thermal overload protection Under voltage lockout protection Adjustable Over-Voltage Protection Switches Watchdog reset Flexibility hardware PMU reset function Power-on reset and start-up timer 2.7 Compact size with

(L) 14 x (W) 12 x (H) 2.1 mm. The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Model No. Page TPN-M101D 12 of 19 Prepared by:

Approved by:

Merry Team Merry Team Marketing Name. Integrated Dongle Revision 03 3 FIRMWARE SPECIFICATION 3.1 Feature/Description

- Support low latency mode when connected with the well-matched earbuds

- Support firmware update via USB connection

- Enter low power mode when USB host in standby mode

- PC control synchronization (audio/media control)

- Support HID interface with the PC client application The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Model No. Page TPN-M101D 13 of 19 Prepared by:

Approved by:

Merry Team Merry Team Marketing Name. Integrated Dongle Revision 03 3.2 USB Interface USB Descriptors Items VID PID Manufacturer String Fields 0x03F0 0x099C HP, Inc Product Name HyperX Wireless Audio USB Specifications Items USB Device Type USB Test Requirement Playback Device Type Playback Channels Playback Bitrate Playback Sampling Frequency Recording Device Type Recording Channels Recording Bitrate Recording Sampling Frequency Minimum Vendor Pages Description USB Audio Class 1.0 USB Chapter 9 Speaker Stereo 16-bit 48000 Hz Microphone Mono 16-bit 16000Hz 3 pages Usage: 0x0001 Usage Page: 0x01C0 o App specific commands o Uses Set/Get Feature Reports Usage Page: 0x170F o App specific notifications o Uses Read Usage page: 0xFFC0 o Factory specific commands o Uses Write/Read The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Model No. Page TPN-M101D 14 of 19 Prepared by:

Approved by:

Merry Team Merry Team Marketing Name. Integrated Dongle Revision 03 4 MECHANICAL 4.1 Shielded case drawing The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Model No. Page TPN-M101D 15 of 19 Prepared by:

Approved by:

Merry Team Merry Team Marketing Name. Integrated Dongle Revision 03 4.2 Antenna connector detail The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Model No. Page TPN-M101D 16 of 19 Prepared by:

Approved by:

Merry Team Merry Team Marketing Name. Integrated Dongle Revision 03 4.3 PCBA Dimensions drawing The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Model No. Page TPN-M101D 17 of 19 Prepared by:

Approved by:

Merry Team Merry Team Marketing Name. Integrated Dongle Revision 03 5 PACKAGE SPECIFICATION 5.1 PCBA 136PCS IC (

136PCS PCBA put into anti-static IC tray (Picture for reference only) 5.2 5 680PCS PCBA 680PCS PCBA in total put into 5-layer tray. 5.3 1 Put an empty tray on top for protection 5.4 Use anti-static strapping to bundle it as below picture showed. The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Model No. Page TPN-M101D 18 of 19 Prepared by:

Approved by:

Merry Team Merry Team Marketing Name. Integrated Dongle Revision 03 5.5 &() Prepare two bags of desiccant & one humidity card. (Place them as below picture showed.) 5.6 Put final product into the aluminum container bag 5.7 Complete vacuum packaging as required 5.8 Paste a shipping label on aluminum bag, then put it into the corrugated paper box. (Label info. TBD) 5.9 Shipping labels are pasted on the corrugated paper box. (Label info. TBD) The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL SPECIFICATIONS Model No. Page TPN-M101D 19 of 19 Prepared by:

Approved by:

Merry Team Merry Team Marketing Name. Integrated Dongle Revision 03 5.10 2PCS*2 4PCS 4PCS of corrugated paper box put into carton, 2PCS*2 layers placed side by side 5.11 &

Stick tamper sticker & carton label on the carton (label info. TBD)

(label info.) The information contained herein is the property of Merry and shall not be distributed reproduced, or disclosed in whole or in part without prior written permission of Merry. RD1-001-008-R02 RL

Declaration Date: January 13, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Examiner:

We declare that this equipment

(Product Name: Embedded HyperX Wireless Module,FCC ID: B94TNM101D) complies with e-CFR Title 47 Part 2.925 (f), as it is too small to be labeled with FCC ID (smaller than 4-6 points). Hence the FCC ID is placed in user manual and packaging instead of being affixed on the equipment. Sincerely, Signature: ____________________ Printed Name /Title: Liang Rong Chiao/ Worldwide Technical Regulations Company Name: HP International Pte. Ltd., Taiwan Branch

Label & Label Location for TPN-Q297 Bottom Side RMN: TPN-Q297 Contains HP Radio Model: TPN-M101D Contains FCC ID: B94TNM101D Contains IC: 466X-TNM101D

TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC IDB94TNM101D To whom it may concern:

Date: 2023.11.03 We, the undersigned, hereby authorize << SGS Taiwan Ltd.>> to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. a. Name, address and contact information of third party:

SGS Taiwan Ltd. Jim Chang Telephone: +886 2 2299 3279 Ext 1194 E-mail: jim.chang@sgs.com No. 134, Wu Kung Rd., New Taipei Industrial Park, Wu Ku District,New Taipei City, 24803 Taiwan b. Term of designation, unless earlier terminated by HP: 1 year. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TIMCO Engineering, Inc, still resides with << HP Inc. >>. This authorization is valid until further written notice from the applicant. __________________________ Liang Rong Chiao / Worldwide Technical Regulations HP International Pte. Ltd., Taiwan Branch 10F-1, 66, Jingmao 2nd Road, Nangang District, Taipei 115. Taiwan frances.liang@hp.com

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6374585.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case 3390 East Harmony Road Fort Collins Colorado 80528 United States U.S. Agent for Service of Process Attestation To the attention of Federal Communications Commission Authorization and Evaluation Division Applicant / Designated U.S Agent Company Name: HP Inc. FRN: 0025126541 Grantee Code: B94 Contact Person: Richard P Tarsio Street Address: 3390 East Harmony Road, Colorado, United States, City/Province/Zip: Fort Collins 80528 Tel.: 970-898-8713 Email: richard.tarsio@hp.com This letter is to confirm that the Applicant has designated itself as the U.S Agent for service of process as required by 2.911(d)(7). The Applicant further acknowledges acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant / U.S. Agent Signature:

Date: 2023-02-21 Signed by (printed name): Person: Richard P Tarsio

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 10-12-2023 Ref: Attestation Statements Part 2.911(d)(5)(i)&(ii) Filing FCC ID: B94TNM101D Statement for 47 CFR section 2.911(d)(5)(i)

[HP Inc.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Statement for 47 CFR section 2.911(d)(5)(ii)

[HP Inc.] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as a specifically named entity or any of its subsidiaries or affiliates that producing covered equipment. Sincerely, Liang Rong Chiao Worldwide Technical Regulations HP International Pte. Ltd., Taiwan Branch 10F-1, 66, Jingmao 2nd Road, Nangang District, Taipei 115. Taiwan frances.liang@hp.com T+886 2 3789-2469

Date: Nov. 10, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 C.C.: SGS Taiwan Limited To Whom It May Concern:

The purpose of this letter is to request a Permissive change for FCC ID: B94TNM101D Original grant date: 03/10/2023 The major change filed under this application is 1. The subject approved module is being used in different host (Portable category Configuration, Host Brand/Model: HP/TPN-Q297) 2. Output power have been decreased and the Bluetooth classic modes have been disabled via firmware settings. 3. EMC & RF exposure are evaluated to demonstrate Compliance. 4. Adding new antenna of same PIFA type with antenna gain -0.8dBi lower than the antenna gain 3.41dBi in the original grant. Best Regards Jim Chang / Manager SGS Taiwan Ltd. Central RF Lab No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan. jim.chang@sgs.com

Date: November 3, 2023 Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: B94TNM101D Pursuant to Sections 0.457(d) and 0.459 of the Commissions Rules and FCC Guidance document 726920, we hereby request permanent confidential treatment of exhibits identified as such in the table below and request they are permanently withheld from public review based on the documents containing trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. We also request short-term confidentiality on certain exhibits until the intended date of marketing as outlined below. We request the exhibits be withheld from public view for a period of 180 days. We attest marketing of the product will only commence after the period of short-term confidentiality expires, or if marketing is to commence before the requested number of days listed above, the grantee will inform Timko to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. Exhibit Block Diagrams Operation Description Parts List & Placement/BOM Tune-Up Procedure Schematic Diagrams External Photos Internal Photos Test Setup Photos Users Manual Type of Confidentiality Requested Permanent Permanent Permanent Permanent Permanent

Permanent*

Permanent*

Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term The asterisked items (*) require further information to be provided in this justification letter before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. Note: any documents held under the Short-Term confidentiality will automatically become public after the requested time if an appropriate extension request has not been received. Any exhibits (i.e., schematic diagrams) that may have already been requested to have Permanent confidentiality as shown above need not be repeated under Short-Term confidentiality request. Sincerely, Signed:

Printed name: Liang Rong Chiao Title: Worldwide Technical Regulations Company Name: HP International Pte. Ltd., Taiwan Branch

Authorization on Behalf of HP Inc. For the US Federal Communications Commission Office of Engineering and Technology and Other FCC Programs and Offices 1. I, Richard P Tarsio, am on the Worldwide Technical Regulations staff of HP Inc. (HP) and Applicant/Grantee Contact of Record for HP Inc. together with its subsidiaries and affiliates worldwide (collectively, HP) for HPs dealings with the United States Federal Communications Commission (FCC). I am duly authorized by HP Inc. to make this Authorization on HP Inc.s behalf. 2. This Authorization will designate the person named below to act on my behalf and HP Inc.s behalf as authorized agent and representative, until further notice, with the additional power to designate one or more third party agents for HP Inc. with regard to particular matters and applications. All acts carried out and requests made by this named representative relating to any matter before the FCC, including requests for confidentiality, shall have the same effect as mine. Name:

Title:

Address:

Telephone:

E-mail:

Rong-Chiao Liang Regulatory Program Manager HP Inc. 10F, No. 66 Jingmao 2nd Rd NanGang District Taipei, Taiwan 11568 866 2 37892469 frances.liang@hp.com 3. Questions about the scope and effect of this Authorization should be addressed as follows:

4. I declare under penalty of perjury that the foregoing is true and correct, and that this Authorization was executed at Fort Collins, Colorado on the date indicated below my signature. Richard P Tarsio US Canada Technical Regulations 3390 East Harmony Road, MS 66 Fort Collins, CO 80528 970 898 8713 Telephone richard.tarsio@hp.com ____________________________ Signature Richard P Tarsio US Canada Technical Regulations HP Inc. Date: 24 June 2016

Justification Letter Date: December 5, 2022 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding FCC ID: B94TNM101D Dear Examiner:

Pursuant to Sections 0.457(d) and 0.459 of the Commissions Rules and FCC Guidance document 726920, we hereby request permanent confidential treatment of antenna photos exhibit. Concerning the antennas are key components of this device, the structure details contained in the antenna photos are trade secrets and proprietary information not customarily released to the public. Sincerely, Signature: __ ___ Printed Name /Title: Jim Chang / Manager Company Name: SGS Taiwan Ltd.

Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: B94TNM101D Items to be covered by Single modular transmitters. 1. The modular transmitter must have its own RF shielding. Answer from applicant Yes, RF shielding cover module transmitter Yes, there is buffer inside RF chip Yes, there is power regulator and power management inside RF chip. Yes, unique connector I-PEX was used for connection between antenna and module. Yes, the modular transmitter must be tested in a stand-alone configuration, Yes, permanently affixed label will be placed on System which include the RF module. Yes, the module comply with applicable operating requirement and adequate instruction was provided. Yes, the module conforms to FCC regulation requirement. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-

modulation. 3. The modular transmitter must have its own power supply regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): Liang Rong Chiao Date:January 12, 2023 Signature: ___________________________