FCC ID: B94-PF011WA USB Wireless Dongle

Quick Start Guide v2 HyperX Pulsefire Haste 2 Mini Wireless Gaming Mouse Overview C D E F A B H I G J O K L M N A. Left click button B. Right click button C. Mouse wheel D. DPI button E. Forward button F. Back button G. USB-C port H. HyperX 26K Sensor [Translate Sensor]

I. Power mode switch J. USB wireless dongle storage K. Grip tape L. Mouse skates M. USB wireless dongle N. Extension adapter O. USB charge / data cable Charging and Wired Mode It is recommended to fully charge your mouse before first use. Connect the mouse to a PC or game console using the included USB cable. USB connectivity will override the selected power mode.

[Requesting to make arrows]

Installation 2.4G Wireless Mode Bluetooth Mode 1. Switch the mouse to 2.4G power mode. 2. Connect USB wireless dongle to the extension adapter. 3. Connect the extension adapter to a PC or game console using the 1. Switch the mouse to Bluetooth power mode. Mouse will flash blue on first setup 2. Go to your computers Bluetooth settings, search and connect to included USB cable. Haste 2 Mini. For optimal placement, keep the extension adapter within 20 cm of the mouse.

[The red highlight of the mouse power button can be black on the QSG] [Make sure centered]

Bluetooth Pairing Hold the left click button, right click button, and DPI button simultaneously until the mouse flashes blue.

[Add black arrows like Haste 2 wireless]

DPI Presets There are 4 default DPI presets: 400 DPI (red) | 800 DPI (blue) | 1600 DPI (yellow) | 3200 DPI (green) HyperX NGENUITY Software To customize lighting, DPI, macro settings, and more, download HyperX NGENUITY software at hyperx.com/ngenuity Questions or Setup Issues Contact the HyperX support team or see user guide at hyperx.com/support

[Compliance Battery/Transmit Power Section ask Compliance team if this needs translation]

[The red highlight of the mouse power button can be black on the QSG] [Make sure centered]

[NGENUITY Logo on the far right]

Battery Information Mouse contains 3.7V, 370mAh Li-Ion Polymer Battery, 1.369Wh Cannot be replaced by user Frequency & TX Power Information Radio Technology: Bluetooth, 2.4GHz Maximum Transmit Power EIRP:

Adapter: < 10mW, Mouse: < 10mW Wireless Mouse//

Regulatory Model//: PF011 Extension Adapter//USB , Model//: PF011A HyperX Pulsefire Haste 2 Mini USB Wireless Dongle/USB /USB Regulatory Model//: PF011WA Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communicat ions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

The product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. NCC statement:

Canada Notices This Class B digital apparatus complies with Canadian ICES-003. Avis Canadian Cetappareilnumrique de laclasseBestconforme lanormeNMB-003 du Canada. Industry Canada statement This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:

The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Dclaration d'exposition aux radiations:

Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada tablies pour un environnement non contrl. Le produit est sr pour un fonctionnement tel que dcrit dans ce manuel. La rduction aux expositions RF peut tre augmente si l'appareil peut tre conserv aussi loin que possible du corps de l'utilisateur ou que le dispositif est rgl sur la puissance de sortie la plus faible si une telle fonction est disponible.

IFETEL: RCPHY PF21-xxxx SDPPI ID xxxxx/SDPPI/2021 2141

[RIRAMATEL C-xxxxx eDanaret XXXXX=XXXXX 12.0mm i

[G R-R-hpi-

PFOMNWA FCC ID: B94-PFOTIWA IC: 466C-PFOTWA CAN ICES-3(B)/NMB-3(B) E USBF SSEHBEE _CCANZ3LPO430T2 aw C&

Made in China/Hi2is/ pee Rating/AE EEE ii WE SER: ALY USBARSERSRISES/ 5V= SOOmA

TCB Authority to Act as Agent Number:

Revision:

Effective date: Oct 8, 2021 MS-0045317 0 Authority to Act as Agent Date: 2023-04-17 TUV Rheinland of North America, Inc. 1279 Quarry Lane., Suite. A Pleasanton, CA 94566 To Whom It May Concern:

I appoint TUV Rheinland of North American Inc., 1279 Quarry Lane, Suite A, Pleasanton, CA 94566, USA to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with HP International Pte. Ltd., Taiwan Branch/ No. 1-

5, Lixing 1st Road, East District, HSZ Hsinchu City, Taiwan_________. For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Date:

___2023-04-17 Agreement is valid for 12 months from the above date. By:

(Signature) Vanessa Tsai__ _________

(Print name) Product Compliance Engineer___

(Title)

+886 932285270__

(Telephone) On behalf of:

HP International Pte. Ltd., Taiwan Branch__

(Company Name) Page 1 of 1

SPECIFICATION FOR APPROVAL CUSTOMER CUSTOMERS P/N PART NUMBER WAN3216F245L08 DESCRIPTION Chip Antenna 3216 L Ant 2.45G Type 08 VERSION V4.0 ISSUE DATE 2020/02/24 CUSTOMER APPROVED APPROVAL Ray R&D CENTER CHECKED Tennyson DRAWN Chun 11261 151 1

: (02) 2898-2220

: (02) 2898-5055 OneWave Electronic Co., Ltd. 1F, No. 151, Li Gong Street, Beitou District, Taipei City 11261, Taiwan TEL: +886 2 2898-2220 FAX: +886 2 2898-5055 3216 Chip antenna For Bluetooth / WLAN Applications P/N: WAN3216F245L08 Dimension (mm) 3.23 0.20 1.66 0.20 0.45 0.20 L W T ONEWAVE TECHNOLOGY CO., LTD. 2/11 Part Number Information WAN 3216 A B F C 245 D L E 08 F Product Series Dimension L x W Material A B C D Working Frequency E F Feeding mode Antenna type Antenna 3.2 x 1.6mm (0.2mm) High K material 2.4 ~ 2.5GHz Loop & Single Feeding Type = 08 1. Electrical Specification Specification WAN3216F245L08 Part Number Central Frequency Bandwidth Return Loss Peak Gain Impedance Operating Temperature Maximum Power 2450 110 (Min.)

-10 (Max) 1.15 50

-40+110 4 MHz MHz dB dBi Ohm W sec. Resistance to Soldering Heats 10 ( @ 260) Polarization Azimuth Beamwidth Termination Linear Omni-directional Ni / Au (Leadless) Remark : Bandwidth & Peak Gain was measured under evaluation board of next page ONEWAVE TECHNOLOGY CO., LTD. 3/11 2. Recommended PCB Pattern Evaluation Board Dimension Suggested Matching Circuit

0.1~0.3nH0.1pF ONEWAVE TECHNOLOGY CO., LTD. 4/11 Layout Dimensions in Clearance area( Size=5.8*9.9mm) FootPrint (Unit : mm) ONEWAVE TECHNOLOGY CO., LTD. 5/11 3. Measurement Results Return Loss ONEWAVE TECHNOLOGY CO., LTD. 6/11 Radiation Pattern X Y Z Efficiency Peak Gain Directivity 2400MHz 64.38 %

1.04 dBi 2.95 dBi 2450MHz 68.15 %

1.15 dBi 2.81 dBi 2500MHz 66.68 %

1.12 dBi 2.88 dBi Chamber Coordinate System ONEWAVE TECHNOLOGY CO., LTD. 7/11 4.Reliability and Test Condictions ITEM Solderability REQUIREMENTS 1. Wetting shall exceed 90% coverage 2. No visible mechanical damage TEMP () 230 150 41 sec. 60sec Solder heat Resistance 1. No visible mechanical damage 2. Central Freq. change :within 6%

1. No visible mechanical damage 1. No visible mechanical damage Component Adhesion

(Push test) Component Adhesion

(Pull test) Thermal shock 1. No visible mechanical damage 2. Central Freq. change :within 6%

Phase 1 2 3 4 303 Within 3sec Temperature() Time(min)

+1105 Room Temperature

-402 Room Temperature 303 Within 3sec Resistance to High Temperature 1. No visible mechanical damage 2. Central Freq. change :within 6%

3. No disconnection or short circuit. Resistance to Low Temperature 1. No visible mechanical damage 2. Central Freq. change :within 6%

3. No disconnection or short circuit. Humidity 1. No visible mechanical damage 2. Central Freq. change :within 6%

3. No disconnection or short circuit. TEST CONDITION Pre-heating temperature:150/60sec. Solder temperature:2305 Duration:41sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Pre-heating temperature:150/60sec. Solder temperature:2605 Duration:100.5sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin The device should be reflow soldered(2305 for 10sec.) to a tinned copper substrate A dynometer force gauge should be applied the side of the component. The device must with-ST-F 0.5 Kg without failure of the termination attached to component. Insert 10cm wire into the remaining open eye bend ,the ends of even wire lengths upward and wind together. Terminal shall not be remarkably damaged.

+110=>303min

-40=>303min Test cycle:10 cycles The chip shall be stabilized at normal condition for 2~3 hours before measuring. Temperature:+1105 Duration: 100012hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Temperature:-405 Duration: 100012hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Temperature: 402 Humidity: 90% to 95% RH Duration: 100012hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. ONEWAVE TECHNOLOGY CO., LTD. 8/11 100.5 sec. 60sec.. TEMP () 150 260 5.Soldering and Mounting Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. The terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. Recommended temperature profiles for re-flow soldering in Figure 1. Products attachment with a soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. Preheat circuit and products to 150 Never contact the ceramic with the iron tip Use a 20 watt soldering iron with tip diameter of 1.0mm 280 tip temperature (max) 1.0mm tip diameter (max) Limit soldering time to 3 sec. ONEWAVE TECHNOLOGY CO., LTD. 9/11 SOLDERINGCOOLINGNATURALPRE-HEATINGTEMPERATURE(C)60~120 s10s max.30~60s250~260230180150TIME(sec.)Reflow SolderingSOLDERINGCOOLINGNATURALPRE-HEATINGTEMPERATURE(C)within 3sGradualcooling150TIME(sec.)Iron SolderingOver 60s350300 6.Packaging Information Tape Specification:

Reel Specification: (7, 180 mm) Tape Width(mm) A(mm) B(mm) C(mm) D(mm) Chip/Reel(pcs) 8 9.00.5 602 13.50.5 1782 3000 ONEWAVE TECHNOLOGY CO., LTD. 10/11 7.Storage and Transportation Information Storage Conditions To maintain the solderability of terminal electrodes:

1. Temperature and humidity conditions: -10~ 40 and 30~70% RH. 2. Recommended products should be used within 6 months from the time of delivery. 3. The packaging material should be kept where no chlorine or sulfur exists in the air. Transportation Conditions 1. Products should be handled with care to avoid damage or contamination from perspiration and skin oils. 2. The use of tweezers or vacuum pick up is strongly recommended for individual components. 3. Bulk handling should ensure that abrasion and mechanical shock are minimized. ONEWAVE TECHNOLOGY CO., LTD. 11/11

Certification Designating Applicant as FCC US Agent To: Federal Communications Commission Date: 04-17-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Attestation Statement Part 2.911(d)(7) filing FCC ID: B94-PF011WA HP Inc. (the applicant) as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC ID. The applicant acknowledge the applicants consent and the designated agent for service of processs obligation to accept service of process. The applicant acknowledge the applicants acceptance to maintain an agent for service of process for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledge the responsibility to inform the FCC whenever the agent information changes. Designated U.S. Agent from Applicant Company Company Name: HP International Pte. Ltd., Taiwan Branch Contact Person: Vanessa Tsai Address: No. 1-5, Lixing 1st Road, East District, HSZ Hsinchu City, Taiwan Tel.: +886 932285270 Email: vanessa.tsai@hp.com FCC FRN: 0025126541 Sincerely yours, Signature Printed Name: Vanessa Tsai Title: Product Compliance Engineer

TCB FCC Request for Confidentiality Letter Number: MS-0044715 Revision:

1 Effective date: Sep 12, 2022 Author:

Owner:

William Graff William Graff Date: 2023-04-17 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Confidentiality Request for FCC ID: B94-PF011WA Pursuant to FCC 47 CRF 0.457(d), the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Permanent Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term n/a Permanent Permanent Permanent Permanent Permanent Permanent Permanent Exhibit Block Diagrams External Photo Internal Photos ***

Operation Description/Theory of Operation Schematics Test Setup***

Tune-Up Procedure Users Manual***

Part List/ Antenna Construction HP Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public.

(*** Exceptional case for Permanent Confidentiality for these Exhibits by PAG only) Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By:

(Signature)

(Print name/Title) Vanessa Tsai / Product Compliance Engineer Tel: +886 932285270 Email: vanessa.tsai@hp.com MS-0044715 Page 1 of 1 Revision 1

Attestation Statements Not Covered Entity Applicant To: Federal Communications Commission Date: 04-17-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(ii) filing FCC ID: B94-PF011WA

[HP Inc.] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely yours, Applicant Signature Printed Name: Vanessa Tsai Title: Product Compliance Engineer Address: No. 1-5, Lixing 1st Road, East District, HSZ Hsinchu City, Taiwan Tel.: +886 932285270 Email: vanessa.tsai@hp.com

Attestation Statements Not Covered Equipment To: Federal Communications Commission Date: 04-17-2023 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) filing FCC ID: B94-PF011WA

[HP Inc.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely yours, Applicant Signature Printed Name: Vanessa Tsai Title: Product Compliance Engineer Address: No. 1-5, Lixing 1st Road, East District, HSZ Hsinchu City, Taiwan Tel.: +886 932285270 Email: vanessa.tsai@hp.com