Hui Zhou Gaoshengda Technology Co., LTD B3LR151 Bluetooth Module Model Number: B3LR151 Product Descrition The B3LR151 is a Bluetooth module that complied with Bluetooth core specification v5.0 and supports dual mode(BR/EDR+Low Energy Controllers).It is compatible with previous versions, including v2.1 + LE. For BR/EDR, it allows multiple active links in either slave mode or master mode. For Low Energy, it supports multiple states and allows multiple active links in slave mode. Product Features Supports Bluetooth classic(BDR/EDR) Supports Bluetooth Low Energy(BLE) Compatible with Bluetooth v2.1 systems,3.0 systems Bluetooth 4.2 Low Energy (LE) Bluetooth v5.0 (1Mbps,2Mbps) High speed USB 2.0 interface RoHS compliant Product Specification Model Bluetooth Module Product Name B3LR151 Standard Interface V2.1,V3.0, V4.2 , V5.0 USB Data Transfer Rate 1,2,3Mbps Modulation Method GFSK, /4-DQPSK, 8DPSK Frequency Band 2400~2483.5 MHz Frequency Range:
2402~2480 MHz Antenna Type:
PCB Antenna Antenna Gain:
3dBi Operating Voltage 3.3V10%
Current Consumption 300mA Operating Temperature 0 ~60C ambient temperature Storage Temperature
-40 ~ 80C ambient temperature Humidity 5 to 95 % maximum (non-condensing) NOTICE:
please keep this product and accessories attached to the places which children can't touch;
do not splash water or other liquid onto this product, otherwise it may cause damage;
do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
please keep this product away from flammable or naked flame;
please do not repair this product by yourself. Only qualified personnel can be repaired. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
PAGE 1 OF 3 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD B3LR151
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC ID:2AC23-B3L any similar wording that expresses the same meaning may be used. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The device must be professionally installed The intended use is generally not for the general public.It is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. the user has no access to the connector. Installation must be controlled. Installation requires special training This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS). It is applicable to the modular transmitter The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile application. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. There is requirement that the grantee provide guidance to the host manufacturer for compliance with Part 15B requirements. The module complies with FCC Part 15.247 and apply for Single module approval. Trace antenna designs: Not applicable. Antennas:
BT PCB antenna & 3 dBi The antenna is permanently attached, cant be replaced. Canada Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. L'metteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR d'Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
1)L'appareil ne doit pas produire de brouillage;
2)L'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC:12290A-B3L any similar wording that expresses the same meaning may be used. l'appareil hte doit porter une tiquette donnant le numro de certification du module d'Industrie Canada, prcd des mots Contient un module d'mission , du mot IC:12290A-B3L ou d'une formulation similaire exprimant le mme sens, comme suit PAGE 2 OF 3 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD B3LR151 The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure andcompliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 etla conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformit de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet metteur ne doit pas tre Co-plac ou ne fonctionnant en mme temps qu'aucune autre antenne oumetteur. Cet quipement devrait tre install et actionn avec une distance minimum de 20 centimtres entre le radiateur et votre corps. Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/ICanada statement). Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. Any company of the host device which install this modular should perform the test of radiated &
condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 &
15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247 and 15.407) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing contains FCC ID: 2AC23-B3LIC: 12290A-B3L l'hte doit utiliser l'instrument uniquement dans des dispositifs qui rpondent la fcc / (catgorie d'exposition rf mobile, ce qui signifie le dispositif est install et utilis une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen dclarations de conformit relatives l'metteur que de montrer dans ce manuel. le fabricant est responsable de la conformit de l'hte, le systme d'accueil avec le module install avec toutes les autres exigences applicables du systme comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommand de confirmer la conformit avec les exigences de la fcc /
(metteur lorsque le module est install dans l'hte. le dispositif d'accueil doivent avoir une tiquette indiquant contient FCC ID: 2AC23-B3LIC: 12290A-B3L PAGE 3 OF 3 Version 1.0