Hui Zhou Gaoshengda Technology Co., LTD
WXT26M2101B
WIFI+BT Module
IEEE 802.11 a/b/g/n/ac/ax 2T/2R
Model Number: WXT26M2101B
Product Descrition
The WXT26M2101B is a complete dual-band(2.4GHz and 5GHz)WIFI 2×2 MIMO module. This module provides a
high level of integration with a dual-stream IEEE 802.11ax MAC/ base band /radio and Bluetooth 5.2.The WLAN
operation supports 20MHz,40MHz and 80MHz channels for data rates up to 1201Mbps. It fully complies with IEEE
802.11 a/b/g/n/ac/ax feature rich wireless connectivity at high standards,delivers reliable,cost-effective,
throughput from an extended distance.
Product Features
◆ Complies with IEEE 802.11b/g/n/ax for 2.4GHz and IEEE 802.11a/n/ac/ax 5GHz Wireless LAN.
◆ Bluetooth v5.2
◆ Two transmit and Two receive path(2T2R)
◆ Works with all existing network nfrastructure.
◆ Capable of up to 128-Bit WEP Encryption.
◆ Freedom to roam while staying connected.
◆ UP to 1201 Mbps High-Speed Transfer Rate in 802.11ax mode of operation.
◆ Operating Systems:Linux,Win7, Win8, Win10,XP
◆ Low power consumption.
◆ Easy to install and configure.
◆ High speed USB 2.0 interface
◆ROHS compliant
Product Specification
Model
WIF+BT Module
Product Name
WXT26M2101B
Standard
Interface
802.11 a /b/g/n/ac/ax
USB
Modulation Method
Data Transfer Rate
1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120 and maximum of 1201Mbps
GFSK,π/4-DQPSK,8DPSK(bluetooth)
IEEE 802.11b: DSSS(CCK)
IEEE 802.11g: OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11n HT20: OFDM (64QAM, 16QAM, QPSK,BPSK)
IEEE 802.11n HT40: OFDM (64QAM, 16QAM, QPSK,BPSK)
IEEE 802.11ax HE20: OFDMA (1024QAM, 256QAM, 64QAM, 16QAM, QPSK,BPSK)
IEEE 802.11ax HE40: OFDMA (1024QAM, 256QAM, 64QAM, 16QAM, QPSK,BPSK)
IEEE802.11a/n HT20/n HT40/ac VHT20/VHT40/VHT80:
OFDM(BPSK,QPSK,16QAM,64QAM,256QAM only in ac mode)
IEEE802.11ax HE20/HE40/HE80:
OFDMA(BPSK,QPSK,16QAM,64QAM,256QAM, 1024QAM)
BLUETOOTH
2402~2480 MHz
WIFI
2.4G: 2412~2462 MHz
5G: 5150~5250MHz,5250 ~ 5350MHz, 5470 ~ 5725MHz, 5725~5850MHz
Infrastructure
Frequency Band
Operation Mode
Security
WEP, TKIP, AES, WPA, WPA2
Operating Voltage
3.3V±10%
Current Consumption
<1000mA
Antenna Type
PIFA
Operating
Temperature
0 ~ 70°C ambient temperature
Storage Temperature
-40 ~ 80°C ambient temperature
Humidity
5 to 95 % maximum (non-condensing)
PAGE 1 OF 4
Version 1.0
Hui Zhou Gaoshengda Technology Co., LTD
WXT26M2101B
NOTICE:
◆please keep this product and accessories attached to the places which children can't touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight, otherwise it may cause
deformation or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part
of your body.
The device must be professionally installed
The intended use is generally not for the general public.It is generally for industry/commercial use.
The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not
normally required. the user has no access to the connector.
Installation must be controlled. Installation requires special training
This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and
CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter
This radio transmitter 2AC23-WXT261has been approved by Federal Communications Commission to operate with
the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that
have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
The concrete contents to check are the following three points.
PAGE 2 OF 4
Version 1.0
Hui Zhou Gaoshengda Technology Co., LTD
WXT26M2101B
1) Must use a PIFA antenna with gain not exceeding 3 dBi
2) Should be installed so that the end user cannot modify the antenna
3) Feed line should be designed in 50ohm
Fine tuning of return loss etc. can be performed using a matching network.
Antenna
Frequency (MHz)
Antenna Type
MAX Antenna Gain (dBi)
2402-2480
PIFA
Antenna
Frequency (MHz)
Antenna Type
MAX Antenna Gain (dBi)
1
1
2
1
2
2412-2462
2412-2462
PIFA
PIFA
5150-5850
5150-5850
PIFA
PIFA
Antenna No.
Frequency Band
Antenna Type
Max Antenna Gain (dBi)
2
2
2
3
3
Notice to OEM integrator
Must use the device only in host devices that meet the FCC RF exposure category of mobile, which means the device
is installed and used at distances of at least 20cm from persons.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
The end user manual shall include FCC Part 15 compliance statements related to the transmitter as show in this
manual (FCC Statement).
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable
requirements for the system such as Part 15 B.
Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when
the module is installed in the host.
Must have on the host device a label showing Contains FCC ID: 2AC23-WXT261.
The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible
when the module is installed inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. It must have on the host device a
exterior label showing Contains FCC ID: 2AC23-WXT261
The use condition limitations extend to professional users, then instructions must state that
this information also extends to the host manufacturer’s instruction manual. This module is
stand-alone modular. If the end product will involve the Multiple simultaneously
transmitting condition or different operational conditions for a stand-alone modular
transmitter in a host, host manufacturer have to consult with module manufacturer for the
installation method in end system.
Any company of the host device which install this modular should perform the test of radiated &
condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 &
15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and
15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247
and 15.407) listed on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular transmitter
grant of certification.
Host manufacturer is strongly recommended to confirm compliance with FCC
PAGE 3 OF 4
Version 1.0
Hui Zhou Gaoshengda Technology Co., LTD
WXT26M2101B
requirements for the transmitter when the module is installed in the host.
Must have on the host device a label showing Contains FCC ID: 2AC23-WXT261.
PAGE 4 OF 4
Version 1.0