Hui Zhou Gaoshengda Technology Co., LTD WXT2NM2611 WIFI+BT Module IEEE 802.11 a/b/g/n/ac/ax 2T/2R Model Number: WXT2NM2611 Product Descrition The WXT2NM2611 is a complete 2.4GHz/5GHz/6GHz WIFI 22 MIMO module. This module provides a high level of integration with a dual-stream IEEE 802.11ax MAC/ base band /radio and Bluetooth 5.2.The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 1201Mbps. It fully complies with IEEE 802.11 a/b/g/n/ac/ax feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput from an extended distance. Product Features Complies with IEEE 802.11b/g/n/ax for 2.4GHz and IEEE 802.11a/n/ac/ax 5GHz Wireless LAN. Bluetooth v5.2 Two transmit and Two receive path(2T2R) Works with all existing network nfrastructure. Capable of up to 128-Bit WEP Encryption. Freedom to roam while staying connected. UP to 1201 Mbps High-Speed Transfer Rate in 802.11ax mode of operation. Operating SystemsLinux,Windows Low power consumption. Easy to install and configure. High speed USB 2.0 interface ROHS compliant Product Specification Model WXT2NM2611 Product Name WIFI+BT Module Standard Interface 802.11 a /b/g/n/ac/axBluetooth Classic and BLE USB Data Transfer Rate Up to 1201Mbps Modulation Method Frequency Band Operation Mode GFSK,/4-DQPSK,8DPSK(Bluetooth Classic) GFSK(BLE) DQPSK,DBPSK,CCK(802.11b) QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n) QPSK,BPSK,16QAM,64QAM with OFDM (802.11a) QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac) QPSK,BPSK,16QAM,64QAM,256QAM,1024QAM with OFDMA (802.11ax) BLUETOOTH (Bluetooth Classic and BLE) 2402~2480 MHz WIFI 2.4G: 2412~2462 MHz 5G: 5180~5320MHz,5500~5720MHz,5745~5825MHz 6G5925~7125MHz Infrastructure Security WEP, TKIP, AES, WPA, WPA2 Operating Voltage 5V10%
Current Consumption 1000mA Antenna Type PCB Operating Temperature
-10 ~ 70C ambient temperature Storage Temperature
-40 ~ 80C ambient temperature Humidity 5 to 95 % maximum (non-condensing) PAGE 1 OF 7 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WXT2NM2611 NOTICE:
please keep this product and accessories attached to the places which children can't touch;
do not splash water or other liquid onto this product, otherwise it may cause damage;
do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
please keep this product away from flammable or naked flame;
please do not repair this product by yourself. Only qualified personnel can be repaired. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 2.2 This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter 2.3 This radio transmitter 2AC23-WXT2N has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points.
) Antenna type is a PCB with no more than -5.9 dBi gain at BT/BLE, 3.43 dBi for 2.4 G WIFI ,4.43 dBi gain for 5G WIFI and 4.94 dBi for 6G WIFI and minimum 4.50 dBi for 6G WIFI.
) Should be installed so that the end user cannot modify the antenna
) Feed line should be designed in 50ohm Fine-tuning of return loss etc. can be performed using a matching network. The antenna shall not be accessible for modification or change by the end user. 2.4 The module complies with FCC Part 15.247 / Part 15.407 and apply for Single module approval. 2.5 Trace antenna designs: Not applicable, the antennas for this module are integrated into the module. Use of external antennas or antennas integrated into the host circuit board are not an option. PAGE 2 OF 7 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WXT2NM2611 2.6 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.7 The antennas are integrated into the module and antenna specifications are provided below. Use of any other antenna type is prohibited. BLE/BT:
Antenna 1 2.4 G wifi:
Frequency (MHz) Antenna Type MAX Antenna Gain (dBi) 2402-2480 PCB
-5.9 Antenna Frequency (MHz) Antenna Type MAX Antenna Gain (dBi) 0 1 5G wifi:
2412-2462 2412-2462 PCB Antenna PCB Antenna 3.43 3.40 Antenna No. Frequency Band 0 1 6G wifi:
5150-5850 5150-5850 Antenna No. Frequency Band 0 1 5925 ~ 7125 5925 ~ 7125 Antenna Type PCB Antenna PCB Antenna Antenna Type PCB Antenna PCB Antenna Max Antenna Gain (dBi) 4.43 4.37 Max Antenna Gain (dBi) 4.92 4.94 2.8 Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as Contains FCC ID: 2AC23-WXT2N; any similar wording that expresses the same meaning may be used. 2.9 In accordance with FCC guidance it is recommended that the host product manufacturer perform investigative measurements to confirm that the system does not exceed the spurious emissions limits or band edge limits once the module is installed in the host system. If the host system contains other transmitters additional testing is required to check for emissions that may occur due to the intermixing of emissions with the other transmitters, digital circuitry, or due to the physical properties of the host product (enclosure). RF exposure assessments to account for transmissions across all transmitters that can operate simultaneously is also required. For additional information refer to FCC KDB 996369 D04 Module Integration Guide. 2.10 The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. PAGE 3 OF 7 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WXT2NM2611 2.11 The host manufacturer is recommended to use FCC KDB 996369 D04 Module Integration Guide recommending as
"best practice" RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties. 2.12 is stand-alone modular. This module the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. the end product will involve If FCC Wi-Fi 6E statement FCC regulations restrict the operation of this device to indoor use only. This module is for client devices only. When installed in a client device use is prohibited for control of or communications with unmanned aircraft systems. In addition of this module is installed in a fixed client device, it is also prohibited on oil platforms, cars, trains, boats, and aircraft, except that indoor access points are permitted to operate in the 5.9256.425 GHz bands in large aircraft while flying above 10,000 feet. This module cannot be installed in a weatherized enclosure and cannot operate from battery but only power sources. The host device must be connected to a power source as it has no battery. Canada Statement This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage;
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC: 12290A-WXT2N any similar wording that expresses the same meaning may be used. l'appareil hte doit porter une tiquette donnant le numro de certification du module d'Industrie Canada, prcd des mots Contient un module d'mission , du mot IC: 12290A-WXT2N ou d'une formulation similaire exprimant le mme sens, comme suit PAGE 4 OF 7 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WXT2NM2611 1the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
1les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour uneutilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 etla conformit l'exposition de RSS-102 RF, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformit de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. IC Wi-Fi 6E Statement:
Devices shall not be used for control of or communications with unmanned aircraft systems. Low-power indoor access points and indoor subordinate devices shall bear statements acknowledging both of the following restrictions in the user manual and, where feasible, in a conspicuous location on the device:
Operation shall be limited to indoor use only. Operation on oil platforms, automobiles, trains, maritime vessels and aircraft shall be prohibited except for on large aircraft flying above 3,048 m (10,000 ft). L'quipement ne doit pas tre utilis pour le contrle ou la communication des systmes d'aronefs sans pilote. Les points d'accs intrieurs de faible puissance et les accessoires intrieurs doivent indiquer les restrictions suivantes dans le manuel de l'utilisateur et, si possible, un endroit bien en vue de l'appareil:
Le fonctionnement doit tre limit un usage intrieur. Il est interdit de travailler sur les plates - formes ptrolires, les voitures, les trains, les navires maritimes et les aronefs, l'exception des gros aronefs de plus de 3 048 mtres (10 000 pieds) Cet metteur ne doit pas tre Co-plac ou ne fonctionnant en mme temps qu'aucune autre antenne oumetteur. Cet quipement devrait tre install et actionn avec une distance minimum de 20 centimtres entre le radiateur et votre corps. PAGE 5 OF 7 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WXT2NM2611 This radio transmitter [IC: 12290A-WXT2N] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points.
) Antenna type is a PCB with no more than -5.9 dBi gain at BT/BLE, 3.43 dBi for 2.4 G WIFI ,4.43 dBi gain for 5G WIFI and 4.94 dBi for 6G WIFI and minimum 4.50 dBi for 6G WIFI.;
) Should be installed so that the end user cannot modify the antenna;
) Feed line should be designed in 50ohm Fine-tuning of return loss etc. can be performed using a matching network. Le prsent metteur radio [IC: 12290A-WXT2N] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Le contenu concret vrifier sont les trois points suivants.
) le type dantenne est une carte PCB avec pas plus que -5.9 dBi gain BT/BLE, 3.43 dBi pour 2.4g WIFI,4.43 dBi gain pour 5G WIFI et 4.94 dBi pour 6G WIFI et minimum 4.50 dBi pour 6G WIFI.;
) doivent tre installs de faon que l'utilisateur final ne peut pas modifier l'antenne
) La ligne dalimentation doit tre conue en 50ohm Le rglage prcis de la perte de rendement, etc. peut tre effectu en utilisant un rseau correspondant.. Antenna type and antenna gain:
BLE/BT:
Antenna 1 2.4 G wifi:
Frequency (MHz) Antenna Type MAX Antenna Gain (dBi) 2402-2480 PCB
-5.9 Antenna Frequency (MHz) Antenna Type MAX Antenna Gain (dBi) 0 1 5G wifi:
2412-2462 2412-2462 PCB Antenna PCB Antenna 3.43 3.40 Antenna No. Frequency Band 0 1 6G wifi:
5150-5850 5150-5850 Antenna No. Frequency Band 0 1 5925 ~ 7125 5925 ~ 7125 Antenna Type PCB Antenna PCB Antenna Antenna Type PCB Antenna PCB Antenna Max Antenna Gain (dBi) 4.43 4.37 Max Antenna Gain (dBi) 4.92 4.94 PAGE 6 OF 7 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WXT2NM2611 Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/Canada statement). Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AC23-WXT2N or IC: 12290A-WXT2N Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC ID and only hosts going into Canada can use the IC ID. Installer should put it in the manual The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems l'hte doit utiliser l'instrument uniquement dans des dispositifs qui rpondent la fcc / (catgorie d'exposition rf mobile, ce qui signifie le dispositif est install et utilis une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen dclarations de conformit relatives l'metteur que de montrer dans ce manuel. le fabricant est responsable de la conformit de l'hte, le systme d'accueil avec le module install avec toutes les autres exigences applicables du systme comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommand de confirmer la conformit avec les exigences de la fcc /
(metteur lorsque le module est install dans l'hte. le dispositif d'accueil doivent avoir une tiquette indiquant contient FCC ID: 2AC23-WXT2NIC: 12290A-WXT2N Les personnes charges de l'installation devraient figurer dans le manuel:
Les dispositifs fonctionnant dans la bande de 5 150 5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Doit avoir sur l'appareil hte une tiquette indiquant Contient l'ID FCC 2AC23-WXT2N ou IC : 12290A-WXT2N L'ID FCC et l'ID IC ne doivent pas tre placs sur l'hte en mme temps et seuls les htes se rendant aux tats-Unis peuvent utiliser l'ID FCC et seuls les htes se rendant au Canada peuvent utiliser l'ID IC. PAGE 7 OF 7 Version 1.0