FCC ID: 2ARNF-M01328 PixelArt Wireless Bluetooth Controller-Hyperkin

Pixel Art Bluetooth Controller Instruction Manual CONTENTS PIXEL ART CONTROLLER CHARGE CABLE

[DIAGRAM]

MODE SWITCH (BT for Bluetooth)/ SW (for Nintendo Switch) TYPE-C CHARGING PORT SYNC RESET PIN LED BATTERY INDICATOR LIGHT LED SYNC INDICATOR LIGHTS HYPERKIN BUTTON (HOME) A B X Y L L2 R R2 TURBO (LIGHTNING BOLT) START SELECT D-PAD LEFT ANALOG STICK / L3 (WHEN PUSHED) RIGHT ANALOG STICK / R3 (WHEN PUSHED)

Quick Reference After youve carefully read the guide below, please refer to this quick reference list when you need it. Select your mode with the MODE SWITCH (BT for Bluetooth)/ SW (for Nintendo Switch) Hold the SYNC button for 3 seconds to start pairing Reconnecting to previously paired device, press SYNC button Hold SYNC button for 5 seconds to turn off controller Getting to Know the Pixel Art Bluetooth Controller XInput and DInput Mode The Pixel Art controller can be used in either XInput or DirectInput (DInput Mode) where applicable. By default, the controller will be in XInput mode. Switching to DInput: While holding the B button and SYNC button simultaneously. The LED SYNC INDICATOR LIGHTS will start flashing two at a time. In DInput mode, the button mapping is as follows:

B = A A = B Y = Y X = X Switch Back to XInput: You can either turn OFF your controller, turn it back ON, then re-pair to your device. It will, by default, be in XInput mode. Alternatively, you can also reset your controller. In XInput mode, the button mapping is as follows:

B = A A = B Y = X X = Y Using a paper clip or similar-sized object, you can (soft) reset the controller by pressing the RESET PIN. Power and Charging The controller will turn off after 15 mins of inactivity to save power. To wake up the controller, press the SYNC button. The controller will sleep after 20 seconds of no Bluetooth connection to a device/console. To charge the Pixel Art Bluetooth Controller, plug the included Type-C cable into the controller's TYPE-

C CHARGING PORT. Plug the other end into an available USB port on your device or any 5V 1A USB power source. When the battery is low, the LED BATTERY INDICATOR LIGHT will blink. When the controller is charging, the LED BATTERY INDICATOR LIGHT will light up solid. When the controller is fully charged, the LED BATTERY INDICATOR LIGHT will turn off. Vibration Settings To turn OFF VIBRATION, press and hold START + SELECT + HYPERKIN BUTTON (HOME) for 5 seconds. Repeat the sequence to turn it back ON. Hyperkin Button (Home) The HYPERKIN BUTTON will light up whenever connected/paired to a device. The HYPERKIN BUTTON's light is set to WHITE by default. To change the color, while holding the TURBO BUTTON, press R3 to cycle through the different colors: RED, ORANGE, YELLOW, GREEN, BLUE, PURPLE, PINK, and WHITE. The HYPERKIN BUTTON will briefly flash each time it is pressed. After a button that has been set to TURBO MODE, the HYPERKIN BUTTON will flash rapidly. To turn OFF the HYPERKIN BUTTON's light, hold START and the HYPERKIN BUTTON for 5 seconds. The HYPERKIN BUTTON will flash three times to indicate it is OFF. To turn the light back on, hold the HYPERKIN BUTTON for 5 Seconds. Using the Turbo Function (Lightning Bolt) 1. While holding the TURBO button, press the button you would like to be set to TURBO MODE. 2. The HYPERKIN BUTTON will flash, indicating the button has been set to TURBO MODE. 3. To turn off TURBO MODE, while holding the button that has been set to TURBO MODE, press the TURBO BUTTON. If successful, the HYPERKIN BUTTON will no longer flash when a button has been pressed. Helpful Tips TURBO MODE does not work for the Nintendo Switch Only the following can be set to TURBO Mode:

A, B, X, Y, L, L2, R, R2, D-PAD Factory Reset If you want to reset the controller to its default factory settings, hold SELECT and Y for 5 seconds. The HYPERKIN BUTTON will flash 3 times to indicate the controller has been reset. It will also light up WHITE. This will also unpair your controller from ALL previously paired devices.

Connecting Your Pixel Art Bluetooth Controller Note: When the term pair/paired is mentioned, it is referring to a Bluetooth/wireless connection, not a wired connection. For the Nintendo Switch Wired Connection 1. Plug the included Type-C cable into the controller's TYPE-C CHARGING PORT. Plug the other end into a USB port on your dock. Make sure the MODE SWITCH is set to SW (to the RIGHT). 2. Once connected, ONE of the LED SYNC INDICATOR LIGHTS will light up solid. Bluetooth Connection 1. Make sure the MODE SWITCH is set to SW (to the RIGHT). Hold the SYNC button for 3 seconds. The LED SYNC INDICATOR LIGHTS will begin to move from left to right. 2. Using either the touch screen or a previously paired controller, go to your console's Home menu. Go to Controllers, then Change Grip/Order. Your controller will begin to pair. Once paired, the LED SYNC INDICATOR LIGHTS will light up solid. Helpful Tips The TURBO button functions as the Share button. Because of this the TURBO function does not work for the Nintendo Switch. Once your controller is paired, if your console enters Sleep Mode, you can re-pair by waking up your console (using the Power button on your console), then pressing the SYNC BUTTON once. The Pixel Art controller supports gyro functions, which are automatically available once paired.

For Windows 10/11 Wired Connection 1. Make sure the MODE SWITCH is set to BT (to the LEFT). Plug the included Type-C cable into the controller's TYPE-C CHARGING PORT. Plug the other end into a USB port on your Windows 10/11 computer. 2. Once connected, ONE of the LED SYNC INDICATOR LIGHTS will light up solid. Bluetooth Connection 1. Make sure the MODE SWITCH is set to BT (to the LEFT). Hold the SYNC button for 3 seconds. The LED SYNC INDICATOR LIGHTS will begin to flash. 2. In Windows 10/11 go to Bluetooth & Devices, then click Add Device. Select Hyperkin Xpad (for XInput) or Hyperkin Pad (for DInput). 3. Once paired, The LED SYNC INDICATOR LIGHTS will light up solid. PC Game Pass Make sure controller is set to XInput mode before playing games in PC Game Pass. Helpful Tips If previously paired, your controller will automatically connect to your computer when SYNC button is pressed.

For Mac (macOS Sierra and Newer) Wired Connection 1. Plug the included Type-C cable into the controller's TYPE-C CHARGING PORT. Plug the other end into a USB port on your Mac. 2. Once connected, ONE of the LED SYNC INDICATOR LIGHTS will light up solid. Bluetooth Connection 1. Make sure the MODE SWITCH is set to BT (to the LEFT). Hold the SYNC button for 3 seconds. The LED SYNC INDICATOR LIGHTS will begin to flash. 2. In macOS, go to System Settings, then click Bluetooth in the sidebar (you may need to scroll down). Select Hyperkin Xpad (for XInput) or Hyperkin Pad (for DInput). 3. Once paired, The LED SYNC INDICATOR LIGHTS will light up solid. PC Game Pass (via browser) Make sure controller is set to XInput mode before playing games in PC Game Pass. Helpful Tips If previously paired, your controller will automatically pair to your computer when the SYNC button is pressed.

For Android Wired Connection 1. To connect to your smartphone, a Type-C to Type-C cable is required (not included). Connect one end of the cable into your controllers TYPE-C CHARGING PORT. Plug the other end into a Type-C port on your device. 2. Once connected, ONE of the LED SYNC INDICATOR LIGHTS will light up solid. Bluetooth Connection 1. Make sure the MODE SWITCH is set to BT (to the LEFT). Hold the SYNC button for 3 seconds. The LED SYNC INDICATOR LIGHTS will begin to flash. 2. Under your Bluetooth settings, look for available devices. Select Hyperkin Xpad (for XInput) or Hyperkin Pad (for DInput). 3. Once paired, The LED SYNC INDICATOR LIGHTS will light up solid. Helpful Tips If previously connected wirelessly, your controller will automatically connect to your computer when the SYNC button is pressed.

Other Devices For Steam Deck Wired Connection 1. To connect to your console, a Type-C to Type-C cable is required (not included). Connect one end of the cable into your controllers TYPE-C CHARGING PORT. Plug the other end into a USB port on your Steam Deck dock. 2. Once connected, ONE of the LED SYNC INDICATOR LIGHTS will light up solid. Bluetooth Connection 1. Make sure the MODE SWITCH is set to BT (to the LEFT). Hold the SYNC button for 3 seconds. The LED SYNC INDICATOR LIGHTS will begin to flash. 2. Press the STEAM button on your console. Under your Bluetooth settings, look for SHOW ALL DEVICES. Toggle this option ON. Select Hyperkin Xpad (for XInput) or Hyperkin Pad (for DInput). 3. Once paired, The LED SYNC INDICATOR LIGHTS will light up solid. For Raspberry Pi Wired Connection*

1. Plug the included Type-C cable into the controller's TYPE-C CHARGING PORT. Plug the other end into a USB port on the Raspberry Pi. 2. Once connected, ONE of the LED SYNC INDICATOR LIGHTS will light up solid.

*Your setup and features may vary depending on your device, including wireless pairing. For Tesla Wired Connection 1. Plug the included Type-C cable into the controller's TYPE-C CHARGING PORT. Plug the other end into the USB port on your Tesla vehicle. 2. Once connected, ONE of the LED SYNC INDICATOR LIGHTS will light up solid

To contact us for help and support, send an email to support@Hyperkin.com. 2023 Hyperkin. Hyperkin and Pixel Art are registered trademarks of Hyperkin Inc. Nintendo Switch is a registered trademark of Nintendo of America Inc. This Hyperkin product is not designed, manufactured, sponsored, endorsed, or licensed by Nintendo of America Inc in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners. All rights reserved. Made in China. FCC Requirement changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

8

5 es s

3 2 3 g ty PS

2 o, lula ww gL 0% OF Of OF 0S 09 OZ O8 06 00bo; 0z Of OF 0S 09 OL 08 06 00Zo1 oz of py EV LT GOVT ATEGAE GATT UT ETE |

Ov 0S 09 OL 08 06 QD} OF 02 O OY 0S 09 OL 08 0 0 Q@zuyrerKIn TETRIS i PIXEL ART CONTROLLER C Fe ReHs

C5266091_X24_Ed.1 Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization for Applicant Company name: Hyperkin,inc Grantee code: 2ARNF FCC ID: 2ARNF-M01328 Contact Name: Jesse Zhang Address: 1939 W. Mission Blvd Pomona California United States 91766 Telephone No: (909) 397-8788 Fax No: (909) 397-8781 Email: jessez@hyperkin.com i. ii for which the equipment

[Hyperkin,inc] certifies that authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification.

[Hyperkin,inc] certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an s entity producing covered equipment. The applicant must sign thi certification. Date: 2023-4-11 Applicants Name: Jesse Zhang Title: manager Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

C5266091_X10_Ed.2 Hyperkin,inc Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2023-4-10 Subject: Request for Confidentiality FCC ID: 2ARNF-M01328 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality NOTE 2 No No No No NOTE 1 NOTE 1 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. short-term Confidentiality, the applicant requests the exhibits selected In case of above are withheld from public view for a period of __180____ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 1/1 C5266091_X10_Ed.2 Sincerely, Signature:

Name:Jesse Zhang Title:manager 1/1

We Hyperkin,inc Statement no.M01328,M01328-TETS, M01328-TEHG,M01328-TEHD,M01328-HFTR,M01328-HFRP, Hereby that The product PixelArt Wireless Bluetooth Controller-Hyperkin, Models M01328-KHOY,M01328-KHCO,M01328-KHLL, M01328-KHHD,M01328-SBEB All models the function, software and electric circuit are the same, only with a product model named different. Test sample modelM01328,. Your assistance on this matter is highly appreciated. Yours sincerely, Signature Company NameHyperkin,inc

C5266091_X8_Ed.1 Letter of Authorization Company: Hyperkin,inc Address:1939 W. Mission Blvd Pomona California United States 91766 Product Name: PixelArt Wireless Bluetooth Controller-Hyperkin Model Number: M01328,M01328-TETS,M01328-TEHG,M01328-TEHD, M01328-HFTR,M01328-HFRP,M01328-KHOY,M01328-KHCO,M01328-KHLL, M01328-KHHD,M01328-SBEB FCC Identifier: 2ARNF-M01328 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. is allowed to forward all Name: Jesse Zhang Date: 2023-4-10 Title: manager Signature of applicant:

1/1

US Agent for Service of Process LETTER OF ATTESTATION TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process:

Company Name: Hyperkin,inc FRN: 0027967017 Contact Name: Jesse Zhang Address: 1939 W. Mission Blvd Pomona California United States 91766 Telephone No: (909) 397-8788 Email: jessez@hyperkin.com Applicant:

Company name: Hyperkin,inc Product Description: 0027967017 Grantee code:2ARNF FCC ID:2ARNF-M01328 Contact Name:Jesse Zhang Address:1939 W. Mission Blvd Pomona California United States 91766 Telephone No: (909) 397-8788 Email:jessez@hyperkin.com

[Hyperkin,inc]certifies that, as of the date of this filing of the application with the TCB, [Hyperkin,inc]is our designated US agent for service of process for the above referenced FCC ID. [Hyperkin,inc]accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and imp ortation or the conclusion of any commission related proceeding involving equipment. [Hyperkin,inc]accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID

. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. Date: 2023-4-11 Applicants Name: Jesse Zhang Title: manager US Agents Name: Jesse Zhang Title: manager Signature Signature 1/1