FCC ID: 2ACQ6-CSC Wireless Scene Controller

Cree Wireless Scene Controller With SmartCast Technology Wireless Scene Controller TOP 5NW1 CSC-SC Includes: CSC-SC-XX INSTALLATION INSTRUCTIONS INSTRUCTIONS DINSTALLATION TOP 5NW1 CSC-SC 120-277VAC 60Hz XX APPLIANCE CONTROLS 18AWG Cu wire Made in China 1 Status LED 3 LINE WIRELESS SCENE CONTROLLER 120-277VAC 60Hz XX APPLIANCE CONTROLS 18AWG Cu wire Made in China Top Button/

Button 1 Button 2 Button 3 Button 4 Button 5 2 NEUT GND LINE LED SUPPLY LEADS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Before installing Wireless Scene Controller turn off the power at the circuit breaker. Couper lalimentation avant linstallation 2. These Wireless Scene Controller must be installed in accordance with the national and local building codes and electrical wiring codes including wiring methods and wiring connections. If you are not familiar with these codes and requirements, consult a Ce produit doit tre install conformment NEC ou votre code lectrique local. Si vous ntes pas familier avec ces codes et ces Indoor use only and suitable for damp locations. Pour usage interieur seulement et convient aux emplacements humides. 3. 4. equipment. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE Voltage: 120-277V, 60Hz Depth in Wall: 1.5"

Type 1 enclosure & IP20 Indoor use Operating Temperature limit of the control: 0 to 35C Software Class A Lighting Controls For ease of installation, Cree recommends the use of a deep wall Pollution degree 2 Suitable for normal household air circulation NOT FOR USE WITH METALLIC FACEPLATES. Operating Control, Electronic Dimming Switch;

The Cree Wireless Scene Controller is used with other SmartCast Technology enabled devices to provide wireless preset/scene control of SmartCast-

enabled LED luminaires. The Cree Wireless Scene Controller provides default and customizable scene controls for up to 14 control zones. UNIT DESCRIPTION LOAD TYPES Cree Wireless Scene Controller support Cree SmartCast Technology enabled devices only. 1 of 3 LPN00838X0002A0_A 2 of 3 GND LINE IN LINE TO LOAD SUPPLY LEADS WIRELESS SCENE CONTROLLER FEATURES INSTALLATION The Cree Scene Controller supports on, off, and dimming controls. See Figure 1. The Cree Wireless Scene Controller supports on, off, and dimming, and color controls. See Figure 1. The Cree Wireless Scene Controller provides preset scene control from a single-gang push-button wallstation. Scenes may be assigned to each of the 5 buttons. See Figure 1. Preset scenes may assign light levels, color temperatures (CCT), or both. NOTE: For ease of installation, Cree recommends using a deep wall box. STEP 1:

Disconnect power to circuit by turning circuit breaker OFF before installation. STEP 2:

If necessary remove existing wall plate and switch. STEP 3:

Strip existing wires ". If two wires will be connected to the same terminal on the Cree device, both wires must be the same gauge

(12AWG or 14AWG). STEP 4:

Wire the LINE (black), NEUTRAL (white), and GND (green or bare) supply wires to the corresponding pigtail leads on the Cree device, as shown in Figure 2. For Scene controllers with no neutral wire. Wire the LINE IN (black) to supply wires, LINE OUT to the switched power, and GND (green or bare) supply wires to the corresponding pigtails on the Cree device, as shown in Figure 3. NOTE: If replacing an existing wall switch, the Wireless Scene Controller shall be wired as instructed; however, the switched power to the load must also be tied directly to the AC supply leads. STEP 5:

Attach the wall plate (reference the wall plate instruction sheet). STEP 6:

Switch the circuit breaker ON. STEP 7:

Press and release any button. The blue LED should blink twice and then go off. If the blue LED does not respond with the two-

blink sequence, please follow the RESET instructions to return the Wireless Scene Controller to factory defaults. LPN00838X0002A0_A Wall Control Troubleshooting Issue Resolution Check wiring

(LINE/NEUT/GND required) Wireless Scene Controller LED does not blink in a 2-blink sequence prior to OneButton Setup Check connected load for wireless dimmers without neutral. Minimum load must be wired to dimmer (minimum load indicated on spec sheet). Wireless Scene Controller will not join a network Reset Device and verify 2-blink sequence for the LED Check wiring (NEUT required) NOTE: LED may illuminate if NEUT not connected Check connected load for wireless dimmers without neutral. Minimum load must be wired to dimmer (minimum load indicated on spec sheet). Reset Device and verify 2-blink sequence for the LED Replaced existing Wireless Scene Controller and fixtures will not turn on Check Wiring (each fixture shall be wired with constant HOT) Wireless Scene Controller will not control fixtures Check group assignments with Configuration Tool RESET WIRELESS SCENE CONTROLLER STEP 1:

Press and hold the TOP button on the Wireless Scene Controller for 30s until the LED flashes fast. STEP 2:

Briefly release the TOP button for less than 1 second (Fast flashing continues). STEP 3:

Press/HOLD the TOP button for 1 second until flashing stops. The LED will then return to the two blink sequence

(discovery mode). CLEANING Clean using a cloth dampened only with water and a little mild detergent. Use of solvents or hydrocarbon-based cleaners may cause permanent damage. FCC NOTICE INDUSTRY CANADA STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the device. This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the device is operated in a commercial environment. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. In addition, this device complies with ICES-003 of the Industry Canada (IC) Regulations. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. In addition, this device complies with ICES-003 of the Industry Canada (IC) Regulations. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 2020 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content is subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree and the Cree logo are registered trademarks and the Cree SmartCast Technology logo is a trademark of Cree, Inc. SmartCast, is a registered trademark of Cree Lighting, A company of IDEAL INDUSTRIES. 3 of 3 www.creelighting.com LPN00838X0002A0_A

30mm * 30mm silk screen Location MODEL:Wireless Scene Controller 120VAC Input:

FCC ID:2ACQ6-CSC IC:11481A-CSC

IDEAL INDUSTRIES LIGHTING LLC,DBA CREE LIGHTING Agent Authorization Company: IDEAL INDUSTRIES LIGHTING LLC,DBA CREE LIGHTING Address: 4401 Silicon Drive Durham,NC 27703 USA Product Name: Wireless Scene Controller Model Number(s): CSC-SC-A-5B-UNVN-WH, CSC-SC-A-5B-UNV-WH, CSC-SC-A-5S-UNVN-WH, CSC-SC-A-5C-UNVN-WH, CSC-SC-A-5S-UNV-WH, CSC-SC-A-5C-UNV-WH Product Description: Zigbee Wireless Scene Controller We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Samir Syal Date: 2021/02/01 Title:

Compliance Engineering Manager Company:

IDEAL INDUSTRIES LIGHTING LLC,DBA CREE LIGHTING

IDEAL INDUSTRIES LIGHTING LLC,DBA CREE LIGHTING Authorization Letter IDEAL INDUSTRIES LIGHTING LLC,DBA CREE LIGHTING 4401 Silicon Drive Durham,NC 27703 USA Addresss declare that the following representative (agent):

Name (person) Bovey Yang Company name Shenzhen STS Test Services Co., Ltd. Addresss 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Baoan District, Shenzhen, Guangdong,China City Shenzhen China Country to act on our behalf on all matters concerning the application and documents submitted to Micom Labs for product certification below Product Description Wireless Scene Controller Type or Model(s) CSC-SC-A-5B-UNVN-WH, CSC-SC-A-5B-UNV-WH, CSC-SC-A-5S-UNVN-WH, CSC-SC-A-5C-UNVN-WH, CSC-SC-A-5S-UNV-WH, CSC-SC-A-5C-UNV-WH Tradename or Brand(s) Date:

Name:

(this must be a person) Function:

Signature:

(or official company stamp) China 2021/02/01 Samir Syal Compliance Engineering Manager We,

(the approval holder) Company name Attestation:

City:

Differences Description We IDEAL INDUSTRIES LIGHTING LLC,DBA CREE LIGHTINGstate:

Product Wireless Scene Controller Model Name CSC-SC-A-5B-UNVN-WH, CSC-SC-A-5B-UNV-WH, CSC-SC-A-5S-UNVN-WH, CSC-SC-A-5C-UNVN-WH, CSC-SC-A-5S-UNV-WH, CSC-SC-A-5C-UNV-WH Brand Name FCC ID 2ACQ6-CSC IC: 11481A-CSC The electrical circuit design, layout, components used, and internal wiring are identical, there're 2 pcs power supply board used (same electrical circuit design, and layout difference). The difference of each number of buttons and appearance. Sincerely, Company: IDEAL INDUSTRIES LIGHTING LLC,DBA CREE LIGHTING Title: Compliance Engineering Manager E-mail: ssyal@creelighting.com Name: Samir Syal Signature

IDEAL INDUSTRIES LIGHTING LLC,DBA CREE LIGHTING Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021/02/01 Subject; Request for Confidentiality FCC ID: 2ACQ6-CSC To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Samir Syal Title: Compliance Engineering Manager