User Manual MTMR1650W User Manual Revision 1.0 MeshTek Labs www.meshtek.com Confidential Page 1 | 5 User Manual Introduction The MeshTek MR16 is an RGBW SmartBulb. Turn On/off, Change color, mix colors, change brightness remotely through any Smart device using our iOS and Android app over Bluetooth Low Energy (BLE) protocol. Features Bluetooth enabled, RGBW Bulb Control colors from your Smart device Dimmable via App (not suitable for use with external dimmers) Input Voltage: 12VAC / 12VDC Download MeshTek app to change Bulb settings Android and iOS compatible Application Spotlight Landscape Lighting Electrical Parameters Wattage: 5.5W Beam Angle: 40 Kelvin Temperature: 2300-8000K Color: RGBW CRI: 70 Operating Temperature: 0 to 25 Lumens: 500lm @ 4000K IP Rating: IP64 MeshTek Labs www.meshtek.com Confidential Page 2 | 5 Block Diagram User Manual Installation Method The basic installation method is the same as that of a standard halogen MR16. Turn off the main power switch of the installation place prior to connection. Before installing the product, the lamp that was being used must be turned off. Replace it once it has sufficiently cooled. Check to see if the socket at the installation location is of the GU5.3 standard. Insert the MR16 SmartBulb perpendicularly into the socket and make sure that pins are fully inserted so that they arent visible. (Be cautious: The socket or product may get damaged if excessive force is applied while handling or plugging in / out the MR16 SmartBulb) Turn the power switch on to see if the product is functioning correctly. Follow the setup process and pair the MR16 SmartBulb with MeshTek app to turn on/off, change color, dim the brightness, etc. MeshTek Labs www.meshtek.com Confidential Page 3 | 5 User Manual FCC Statement REGULATORY APPROVAL a. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. Important Note: FCC RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. IC compliance b. This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. Under Innovation, Science and Economic Development Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Innovation, Science and Economic Development Canada. To reduce potential radio interference to other users, the antenna type and its gain should be chosen in such a way that the equivalent isotropically radiated power (e.i.r.p.) is not more than that is necessary for successful communication. Important Note: IC Radiation Exposure Statement This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. c. Conformit aux norms dIC Cet appareil est conforme la(aux) norme(s) RSS sans licence dInnovation, Science and Economic Development Canada. Son utilisation est soumise aux deux conditions suivantes:
Cet appareil ne doit pas causer dinterfrences et MeshTek Labs www.meshtek.com Confidential Page 4 | 5 User Manual il doit accepter toutes interfrences reues, y compris celles susceptibles davoir des effets indsirables sur son fonctionnement. Conformment aux rglementations dInnovation, Science and Economic Development Canada, cet metteur radio ne peut fonctionner qu laide dune antenne dont le type et le gain maximal (ou minimal) ont t approuvs pour cet metteur par Innovation, Science and Economic Development Canada. Pour rduire le risque dinterfrences avec dautres utilisateurs, il faut choisir le type dantenne et son gain de telle sorte que la puissance isotrope rayonne quivalente (p.i.r.e) ne soit pas suprieure celle requise pour obtenir une communication satisfaisante. Note importante: dclaration d'exposition au rayonnement IC Cet quipement respecte limites dexposition aux rayonnements IC RSS-102 dfinies pour un les environnement non contrl. Il doit tre install et utilis en maintenant une distance minimum de 20 cm entre le radiateur et votre corps. MeshTek Labs www.meshtek.com Confidential Page 5 | 5