FCC ID: 2AEHU-MESHTEK-H52 MeshTek BLE Module

.. MeshTek-H52 Bluetooth 4.2 Low Energy Module GENERAL DESCRIPTION BLE modules from Ilumi make it easy to add single - mode Bluetooth Low Energy (BLE), high range application devices. The fully approved, programmable modules feature ilumi innovative technology, which significantly simplifies BLE module integration in range constrained. The DUT has a small factor of 17.4mmx20.4mmx3mm, it consists of pcb antenna. FEATURES Long-range, module connectivity up to 120 meters Up to +18 dBm TX power / -96dBm RX sensitivity, RSSI monitoring for proximity applications Power Configurable in 4dB step Castellated SMT pads for easy and reliable PCB mounting with internal pcb antenna Simple & fast integration with development kits and sample iOS & Android API Built-in reliable Connection based mesh to support large data packets, Mesh Network

(Node and Bridge) for Android Over the Air firmware update from one device to an entire network 32-bit ARM Cortex M4F nRF52832 CPU No. of GPIOs available for user - 26 Configurable I/O mapping for analog and digital Supports master and slave configurations Lead Free and RoHS Compliance APPLICATIONS Lighting bulbs and fixtures Health & Fitness Equipment Automotive Home Automation Power plugs, routers AV consoles Internet of Things (IoT) Industrial Control ilumi Solutions Inc www.ilumisolutions.com P a g e 1 | 8 MESHTEK-H52 ELECTRICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS Description VDD - Supply Voltage Built-in Crystal Frequency Min 1.7V Nom 3.3V 32 MHz Max 3.6V Radio Operating Frequencies 2402MHz 2480 MHz Notes 1 MHz channel spacing Radio On-Air data rate Radio Output Power Receiver Sensitivity @ BLE UART Baud Rate SPI Bit Rate TWI Bit Rate Analog-to-Digital Converter (ADC) ENIB ADC Internal Reference Voltage Internal Temperature Sensor Range General Purpose I/O (GPIO) input high voltage General Purpose I/O (GPIO) input low voltage Output standard drive current Supply Current (TX) Supply Current (RX) System ON, No RAM retention, Wake on any event System ON, Full RAM retention, Wake on any event PIN DESCRIPTION Pin No 1 2 3 4 5 6 7 Pin Name GPIO29/AIN5 GPIO30/AIN6 GPIO0/XL1 GPIO2/AIN0 GPIO4/AIN2 GPIO1/XL2 GPIO3/AIN1 0.125 Mbps 100 kbps BLE 1Mbps

+18 dBm

-96 dBm 1000 kbps 8 Mbps 400 kbps 12 bit 1.2V, 1.8V, 2.4V

-40 C 0.7 * VDD VSS 85 C VDD 0.3 * VDD RF output power configured to +18dBm using external PA Ideal transmitter 12-bit/200KSPS ADC 20 mA 65mA 22.5mA

+18dBm output Power Radio RX Active 1.5uA 1.2uA Function General purpose input/output/ADC input 5 General purpose input/output/ADC input 6 General purpose input/output/RTC Input General purpose input/output/ADC input 0 General purpose input/output/ADC input 2 General purpose input/output/RTC Output General purpose input/output/ADC input 1 ilumi solutions, inc. www.ilumisolutions.com P a g e 2 | 8 MESHTEK-H52 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 GPIO5/AIN3 GPIO6 GPIO7 GPIO8 GPIO9/NFC1/UART_TX GPIO11/UART_RX GPIO10/NFC2 GPIO13 GPIO14 GPIO15 GPIO16 SWDIO SWDCLK GPIO12 GPIO17 VSS1 VSS2 VSS3 VSS4 VDD4 VDD3 VDD1 VDD2 GPIO21/RESET GPIO24 GPIO25 GPIO26 GPIO27 GPIO28/AIN4 General purpose input/output/ADC input 3 General purpose input/output General purpose input/output General purpose input/output General purpose input/output/NFC1/UART TXD General purpose input/output/ UART RXD General purpose input/output/NFC2 General purpose input/output General purpose input/output General purpose input/output General purpose input/output SWD data input/output SWD Clock General purpose input/output General purpose input/output GND GND GND GND 3.3V Power supply input 3.3V Power supply input 3.3V Power supply input 3.3V Power supply input General purpose input/output/Reset General purpose input/output General purpose input/output General purpose input/output General purpose input/output General purpose input/output/ADC input 4 ilumi solutions, inc. www.ilumisolutions.com P a g e 3 | 8 RECOMMENDED PCB FOOTPRINT MESHTEK-H52 17.1990 Module Keep-Out Area: - An area of 1.5mm around the module should be reversed as a keep-out area. No component should be placed in this area. APPLICATION NOTES All dimensions are in mm Ensure there is no copper in the antenna keep out area on any layer of the host PCB. Also keep all mounting hardware or any metal clear of the area to prevent affecting proper radiation pattern. For best antenna performance the module should be placed on the edge of the host PCB and preferably in the corner with the antenna facing the corner. Antenna keep out area definition comes from the module design document or can be referred to the antenna datasheet. Ensure no exposed copper under module on host PCB to avoid shorting to bottom on the underside of the module. ilumi solutions, inc. www.ilumisolutions.com P a g e 4 | 8 SOLDER REFLOW PROFILE MESHTEK-H52 A. Zone A: Preheat: This raises the temperature at a controlled rate, typically 0.5 - 2C/s. This will preheat the component to 120C to 150C to distribute the heat uniformly to the PCB. B. Zone B: Equilibrium1: In this zone, the flux becomes soft and uniformly spreads solder particles over the PCB board, preventing re-oxidization. The recommended temperature for this zone is 150C to 200C for 60s to 120s. C. Zone C: Equilibrium2: This is optional and in order to resolve the upright component issue. Temperature is 210C to 217C for 20s to 30s. D. Zone D: Reflow zone: The temperature should be high enough to avoid wetting but low enough to avoid component deterioration. The recommended peak temperature is 230C to 250C. The soldering time should be 30s to 90s when the temperature is above 217C. E. Zone E: Cooling: The cooling rate should be fast to keep the solder grains small which will give a longer lasting joint. A typical cooling rate is 4C/s ilumi solutions, inc. www.ilumisolutions.com P a g e 5 | 8 MESHTEK-H52 REGULATORY APPROVAL 1. European Union regulatory compliance The MESHTEK_H52 module conforms to the product specifications listed in below Table. MESHTEK-H52 ETSI Conformity R&TTE directive 1999/5/EC EMC Standard ETSI EN 300 328 V1.9.1 (2015-02) EN 62479: 2010 ETSI EN 301 489-1 V1.9.2(2011-09) ETSI EN 301 489-17 V2.2.1(2012-09) 2. FCC and IC Compliance The MESHTEK_H52 module conforms to the product specifications listed in below Table. MESHTEK-H52 FCC and IC Conformity FCC IC Bluetooth Standard FCC part 15 modular certification MESHTEK-H52 FCC ID: 2AEHU-MESHTEK-H52 Industry Canada RSS-247 modular certification MESHTEK-H52 IC: 20059-MESHTEKH52 RF-PHY Component (Tested); QDID: 80428 a. FCC Statement To integrate this module into the host, the host manufacturer is responsible for the applicable FCC rules, including the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. In the user manual of the host device, the following statements are required to be included. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver connected Consult the dealer or an experienced radio/TV technician for help ilumi solutions, inc. www.ilumisolutions.com P a g e 6 | 8 MESHTEK-H52 FCC CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment b. IC compliance This device complies with Industry Canada license-exempt RSS standard(s). This device complies with FCC 15.209 radiation limits for Class B digital devices requirement, operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be chosen in such a way that the equivalent isotropically radiated power (e.i.r.p.) is not more than that is necessary for successful communication. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. c. Conformit aux norms dIC Cet appareil est conforme la(aux) norme(s) RSS sans licence dIndustry Canada. Son utilisation est soumise aux deux conditions suivantes:

1. Cet appareil ne doit pas causer dinterfrences et 2. il doit accepter toutes interfrences reues, y compris celles susceptibles davoir des effets indsirables sur son fonctionnement. Conformment aux rglementations dIndustry Canada, cet metteur radio ne peut fonctionner qu laide dune antenne dont le type et le gain maximal (ou minimal) ont t approuvs pour cet metteur par Industry Canada. Pour rduire le risque dinterfrences avec dautres utilisateurs, il faut choisir le type dantenne et son gain de telle sorte que la puissance isotrope rayonne quivalente (p.i.r.e) ne soit pas suprieure celle requise pour obtenir une communication satisfaisante. Cet quipement respecte limites dexposition aux rayonnements IC RSS-102 dfinies pour un environnement non contrl. Il doit tre install et utilis en maintenant une distance minimum de 20 cm entre le radiateur et votre corps. 3. OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS The MESHTEK-H52 Module has been certified for integration into products only by OEM integrators under the following conditions:

les This device is granted for use in configurations in which the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all person and not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). ilumi solutions, inc. www.ilumisolutions.com P a g e 7 | 8 MESHTEK-H52 IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. 4. OEM Labeling requirements for end product For an end product using the MESHTEK-H52 module there must be a label containing, at least, the following information:

This device contains FCC ID: 2AEHU-MESHTEK-H52 IC: 20059-MESHTEKH52 The label must be affixed on an exterior surface of the end product such that it will be visible upon inspection in compliance with the modular approval guidelines developed by the FCC. In accordance with 47 CFR 15.19, the end product shall bear the following statement in a conspicuous location on the device: "This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation."

When the device is so small or for such use that it is not practicable to place the statement above on it, the information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. In case, where the final product will be installed in locations where the end-user is not able to see the FCC ID and/or this statement, the FCC ID and the statement shall also be included in the end-product manual. ORDERING INFORMATION Table below provides ordering information for the MESHTEK-H52 module. ORDERING INFORMATION Part Number Description MESHTEK-H52 Bluetooth High Power Module Note: For custom applications, contact ilumi Solutions Inc. representative ilumi solutions, inc. www.ilumisolutions.com P a g e 8 | 8