FCC ID: Q639522A Satellite L Band Transceiver 9522A

43755_user_guide 2/1/05 5:00 PM Page 1 9522A L-BAND TRANSCEIVER USERS GUIDE 43755_user_guide 2/1/05 5:00 PM Page 2 Contents Export Compliance Information . 1 1 Product Overview . 1 2 Standards Compliance . 1 2.1 FCC Compliance . 1 2.2 CE Compliace . 1 3 Physical Specifications . 2 3.1 Environmental . 2 3.2 Dimensions . 2 3.3 Interface Connectors . 3 3.3.1 Multi-Interface Connector . 3 3.3.2 Antenna Connector . 4 3.3.3 SIM Chip Reader . 4 3.4 Mounting . 4 3.5 Connector Sealing in Harsh Environments . 5 4 Electrical Interfaces . 5 4.1 DC Power Interface. 5 4.1.1 DC Power Interface Signal Specifications . 5 4.1.2 DC Power Input Specifications 5 4.2 Control/Digital Audio

(DPL Bus) Interface . 6 4.2.1 Control/Digital Audio Interface Signal Descriptions . 6 4.3 RS232 Data Interface . 6 43755_user_guide 2/1/05 5:00 PM Page 3 4.3.1 RS232 Data Signal Descriptions . 6 4.3.2 Autobaud . 6 4.4 Analog Audio Interface . 6 4.4.1 Analog Audio Interface Signal Descriptions.. 6 4.5 SIM Interface . 6 4.6 RF Interface . 7 4.6.1 RF Interface Specifications . 7 4.6.2 Radio Characteristics . 7 5 Instructions for Safe Installation . 7 5.1 Instructions for the Integrator 7 5.2 Instructions from the Integrator 8 6 Modem Commands and Configuration8 Warranty. 9 1 Coverage. 9 2 Conditions. 9 3 Obtaining Warranty Service . 9 4 General Provisions . 10 5 Conditions of Use. 10 6 State Law . 11 7 Contact . 11 Declaration of Conformity . 12 43755_user_guide 2/1/05 5:00 PM Page 4 Export Compliance Information This product is controlled by the export laws and regulations of the United States of America. The U.S. Governement may restrict the export or re-export of this product to certain individuals and/or des-

tinations. For further information, contact the U.S. Department of Commerce, Bureau of Industry and Security or visit www.bis.doc.gov. 1 Product Overview The 9522A L-Band Transceiver (LBT) is designed to be integrated into a specific application with other hardware and software to pro-

duce a solution designed for a specific application or vertical market. Some examples of these solutions include a maritime voice telepho-

ny terminal or a vehicle tracking solution. The LBT functionally supports all of Iridiums voice and data servic-

es. Applications can be built to use one or multiple services using the voice and data interfaces. The 9522A is a functional replacement to the 9522 Sebring LBT. However it should be noted that there are some differences to the voice interface. The 9522A is regulatory approved for FCC, Canada, and CE assum-

ing an antenna with a gain of 3 dBi. This allows the LBT to be inte-

grated into a variety of subscriber products, or retrofitted into exist-

ing LBT-based products. These products, when integrated together will require Regulatory testing to be conducted by the integrator. The LBT is essentially provided as a black box with all interfaces provided via a DB25 connector. The product provides the core trans-

ceiver module and SIM card reader. All other functions and hardware such as keypad, display, power supply, antenna etc. must be provid-

ed by the solution developer. The DB25 provides the following inter-

faces and connections:

Analog Audio Control / Digital Audio RS232 Power Input On / Off 2 Standards Compliance The 9522A is designed to comply with the standards for Radio Emissions Compliance, Electromagnetic Compatibility, and AC Safety in the United States, European Union and Canada. 2.1 FCC Compliance The 9522A is certified under 47 CFR Part 25 as FCC ID:Q639522A. It also complies with Part 15 of the FCC Regulations. Operation is sub-

ject to the condition that this device does not cause harmful interfer-

ence. Any changes or modifications, including the use of a non-stan-

dard antenna, not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IMPORTANT: To comply with FCC RF exposure requirements, a min-

imum separation of 20 cm is required between the antenna and all persons. 2.2 CE Compliance This product, when marked with the CE symbol, complies with the European Community Council Directive for R&TTE, 99/5/EC, provid-

ed that the integrator/user adheres to the instructions detailed in this LBT Interface Specification. This product is in compliance with appli-

cable ETSI standards. Compliance with the requirements of ETSI EN 301 489 requires the use of a shielded digital data interface cable. 1 43755_user_guide 2/1/05 5:00 PM Page 5 3 Physical Specifications The 9522A LBT is depicted in Figure 1 below. Figure 1: Top View 3.1 Environmental The environmental specifications of the 9522A LBT are summarized in Table 1 below. Table 1: Environmental Specifications Parameter Operating Temperature Range Operating Humidity Range Storage Temperature Range Storage Humidity Range Value

-10C to + 55C 75% RH

-40C to + 85C 93% RH 3.2 Dimensions The overall dimensions of the 9522A LBT and its weight are summa-

rized in Table 2 below. Dimensioned views of the 9522A LBT are shown in Figures 2-5 to follow. Table 2: Mechanical Dimensions Parameter Value Length (including antenna connector) 216.1mm (8.51) Length (excluding antenna connector) 196.4mm (7.73) 82.6mm (3.25) Width 39.0mm (1.54) Depth Weight (approximate) 659g Figure 2: Side View 2 43755_user_guide 2/1/05 5:00 PM Page 6 Figure 3: Bottom View Figure 4: Antenna Connector End View Figure 5: Multi-Interface Connector End View 3.3 Interface Connectors The 9522A LBT incorporates three interface connectors. Multi-Interface Connector (located on the end of the 9522A LBT) Antenna Connector (located on the end of the 9522A LBT; opposite to the multi-interface connector) Subscriber Identity Module (SIM) Chip Connector

(located beneath a cover plate atop the 9522A LBT) 3.3.1 Multi-Interface Connector The multi-interface connector is a 25 pin D-subminiature type that includes four interfaces. DC Power Control/Digital Audio (DPL bus) RS232 Data Analog Audio The pin out information for this connector is given in Table 3 below. 3 43755_user_guide 2/1/05 5:00 PM Page 7 Table 3: 25-way connector pin-out Contact Signal Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20*

21 22 23 24 25 EXT_ON_OFF External connection for On / Off key input to Daytona LBT EXT_11HZ 90ms frame sync signal (used in testing) EXT_GND Power Ground input to Daytona LBT EXT_PWR Power input to Daytona LBT SPKR_AUD Speaker audio output from Daytona LBT DA_TX DF_RI DF_RTS DF_S_TX DF_DCD DA_FS DA_CLK DF_S_RX 0V PCM digital audio output from Daytona LBT Data / Fax Ring Indication output from Daytona LBT Data / Fax Request to Send input to Daytona LBT Data / Fax (UART) data input to Daytona LBT Data / Fax Data Carrier Detect output from Daytona LBT PCM digital audio frame sync output from Daytona LBT PCM digital 2.048MHz audio clock output from Daytona LBT Data / Fax data (UART) output from Daytona LBT Signal ground, 0V signal reference and return MIC_AUD Microphone audio input to Daytona LBT EXT_PWR Power input to Daytona LBT EXT_GND Power Ground input to Daytona LBT DPL_TX DF_DTR DPL_RX DF_DSR DF_CTS 0V DA_RX 0V Digital Peripheral Link (UART) data output from Daytona LBT Data / Fax Data Terminal Ready input to Daytona LBT Digital Peripheral Link (UART) data input to Daytona LBT Data / Fax Data Set Ready output from Daytona LBT Data / Fax Clear to Send output from Daytona LBT Signal ground, 0V signal reference and return PCM digital audio input to Daytona LBT Signal ground, 0V signal reference and return 3.3.2 Antenna Connector The 9522A LBT provides a single 50, TNC type antenna connector both transmit and receive. 3.3.3 SIM Chip Reader An integrated SIM chip reader is provided on the 9522A LBT. This connector allows installation of the chip form of the SIM beneath a cover plate on the 9522A LBT housing. 3.4 Mounting The 9522A LBT incorporates (6) mounting holes on its bottom sur-

face that can aid in its mounting. See Figure 3 for locations of these features. It is recommended that a thread-forming screw be used to mount the 9522A LBT via these features. Particularly, a Textron Camcar Taptite II Thread-Rolling Fastener of M3.5x0.6 thread type is recommended. This fastener has a 15IP Torx Plus pan head and is available in lengths of 6, 8, 12, 16, and 20 mm as part number 3BE-P802-00, 3BE-P803-00, 3BE-P8185-00, 3BE-P804-00, 3BE-

P8186-00, and 3BE-P8187-00 respectively. Length should be chosen to ensure that penetration into the 9522A LBT housing does not exceed 11mm. If a 6-32 thread type is desired, a Textron Camcar Taptite II Thread-Rolling Fastener with a 15IP Torx Plus pan head is available in lengths of 1/4, 5/16, 3/8, 1/2, 5/8, 3/4, and 1 inch as part number 3BE-P814-00, 3BE-P8123-00, 3BE-P815-00, 3BE-P816-00, 3BE-

4 43755_user_guide 2/1/05 5:00 PM Page 8 P8124-00, 3BE-P817-00, and 3BE-P818-00 respectively. A 10IP Torx Plus flat head version is also available in a single length of 1/2 inch as part number 3BE-P801-00. Another 6-32 thread type option is to insert a helical coil insert with a 6-32 internal thread into these fea-

tures thus accommodating 6-32 threaded fasteners as mounting hardware for the 9522A LBT. National Aerospace Standard NASM122238 serves as a technical reference for the recommended helical coil insert. 3.5 Connector Sealing in Harsh Environments If the 9522A LBT is to be used in a harsh environment with exposure to high humidity or water, the mating of the multi-interface connec-

tor must be further sealed to protect from moisture entry. It is recom-

mended that a bead of RTV silicone sealant be placed on the con-

nector mating to the 9522A LBTs multi-interface connector where shown in Figure 6 below. A material similar to Permatex 16B should be used. Figure 6: Place a bead of Silicone RTV material along this area all around the connector mating to the 9522A LBTs multi-interface con-

nector. 4 Electrical Interfaces The subsections to follow contain interface information for the elec-

trical interfaces of the 9522A LBT. 4.1 DC Power Interface 4.1.1 DC Power Interface Signal Descriptions The DC power interface is comprised of the DC power inputs and a control signal as summarized in Table 4 below. The EXT_PWR and GND inputs are used to supply DC power to the 9522A LBT. The EXT_ON_OFF control input is pulled to a GND level to toggle the 9522A LBT on and off. Note that both pairs of pins should be con-

nected for EXT PWR and EXT GND. Table 4: Control/Audio Interface Signal Descriptions Signal Description Signal Name EXT_PWR (pin 4 and 16) External power +4.4VDC input EXT_GND (pin 3 and 17) External power GND input EXT_ON_OFF (pin 1) Power on/off control input 4.1.2 DC Power Input Specifications The DC power requirements for the 9522A LBT are summarized in Table 5 below. Note that these requirements apply to DC power measured at the 9522A LBT multi-interface connector input. 5 43755_user_guide 2/1/05 5:00 PM Page 9 Parameter Main Input Voltage - Range Main Input Voltage Nominal Main Input Voltage Ripple Peak Input Current (maximum) Main Input Active Power (average) Main Input Standby Power (average) Table 5: DC Power Input Specifications Value

+4.0 VDC to +4.8 VDC 4.4VDC 40 mVpp 2.5 A @ 4.4 VDC 2000 mW 550 mW 4.2 Control/Digital Audio (DPL bus) Interface 4.2.1 Control/Digital Audio Interface Signal Descriptions The control/digital audio interface enables peripherals such as hand-

sets and SIM card readers to be interfaced to the 9522A LBT. The interface utilises an Iridium Proprietary communication bus not detailed in this fact sheet. Details can be made available after appro-

priate Non-disclosure Agreements and /or License Agreements are executed. 4.3 RS232 Data Interface 4.3.1 RS232 Data Signal Descriptions The RS232 data interface is comprised of eight standard RS232 data, control, and status signals plus a ground level signal reference. This interface allows a connected Data Terminal Equipment (DTE) to utilize the 9522A LBTs modem functionality via AT command con-

trol. A 3-wire RS232 Data minimal interface may also be implement-

ed however the 9 wire interface offers better control and is the rec-

ommended implementation. 4.3.2 Autobaud The Daytona default is for autobaud to be enabled. Autobaud will occur on the following characters a, A, CR (carriage return). Autobaud will also occur on the escape sequence character, provid-

ed this is an odd number character. Normally this is set to + in reg-

ister S2 see AT Command Reference for details. 4.4 Analog Audio Interface 4.4.1 Analog Audio Interface Signal Descriptions The analog audio interface is comprised of the analog audio input and output signals referenced to the 0V signal ground as summa-

rized in Table 6 below. Table 6: Analog Audio Interface Signal Descriptions Signal Description Analog audio input to LBT Analog audio output from LBT Signal ground Signal Name MIC_AUD (pin 15) SPKR_AUD (pin 5) 0V (pin 14, 23 and 25) 4.5 SIM Interface An integrated SIM chip reader is provided on the 9522A LBT. An external SIM card reader may also be interfaced as a peripheral to the 9522A LBT via the DPL bus (control/audio interface). A SIM card in the external reader will take precedence over the SIM chip in the integrated connector when both are present. 6 43755_user_guide 2/1/05 5:00 PM Page 10 4.6 RF Interface 4.6.1 RF Interface Specifications The RF interface requirements for the 9522A LBT are summarized in Table 7 below. Table 7: General RF Parameters Parameter Frequency Range Duplexing Method Oscillator Stability Input/Output Impedance 50 Multiplexing Method Value 1616 MHz to 1626.5 MHz TDD (Time Domain Duplex) 1.5 ppm TDMA/FDMA 4.6.2 Radio Characteristics The tables within this section contain radio characteristics of the 9522A LBT. Table 8: In-Band Characteristics Parameter Average Power during a transmit slot (max) Average Power during a frame (typical) Receiver Sensitivity at 50W (typical) Receiver Spurious Rejection at offsets > 1 MHz (typical) 60 dB Value 7 W 0.6 W

-118.5 dBm Table 9: Link Margin Configuration 9522A LBT with accessory antennas

(Note 1) Cable Loss Link Margin 2 dB (Note 2) 13.1 dB (Note 3) Note 1: Other antenna options are available Note 2: Cable losses should be minimized Note 3: Link Margin given for free space 5 Instructions for the safe Installation and use of the 9522A LBT The 9522A LBT is intended for integration into a finished product. The integrator of the 9522A LBT is required to connect a power sup-

ply, antenna, and user interface to the 9522A LBT. To ensure that the 9522A LBT is correctly installed the following general instructions

(sub-section 5.1) are provided for the installer. The integrator will be required to supply the end user of the integrat-

ed product, incorporating the 9522A LBT, with operating instructions and any other information relating to the maintenance and safety of the equipment (sub-section 5.2). 5.1 Instructions for the Integrator The 9522A LBT must be installed by an appropiately qualified installer and mounted securely as described in section 3.4 of this document. The power supply used to power the 9522A LBT must be checked to ensure it meets the requirements of sub-section 4.1.2 of this docu-

ment. Electrical connections to the 9522A LBT multi-interface connector shall be as designated in Table 3 of sub-section 3.3.1 of this docu-

ment. 7 43755_user_guide 2/1/05 5:00 PM Page 11 The current and voltage rating of the multi-interface connector cable shall meet the requirements of the LBT DC power input. The electrical characteristics of the multi-interface connector cable shall not degrade the 9522A LBT digital communications and analog audio signals. The multi-interface connector cable will provide adequate screening from external electromagnetic interference. The 9522A LBT shall not be located in close proximity to sources of extreme temperature which will cause it be operated outside of its temperature specification (-10C to +55C). The 9522A LBT shall not be operated without an appropriate anten-

na connected to its Antenna connector via a suitable 50ohm coaxial cable. This antenna shall be sited at least 20cm away from any per-

son. 5.2 Instructions from the integrator to the user To comply with the requirements of sub-clause 1.7.2 (Safety instruc-

tions) of the European Information technology equipment safety standard EN60950-1:2002 the integrator must ensure that:

Sufficient information shall be provided to the USER concerning any condition necessary to ensure that, when used as prescribed by the manufacturer, the equipment is unlikely to present a hazard within the meaning of this standard. If it is necessary to take special pre-

cautions to avoid the introduction of hazards when operating, installing, servicing, transporting or storing equipment, the neces-

sary instructions shall be made available. As part of these instructions the installer should inform the user that they should not service the 9522A LBT. 6 Modem Commands and Configuration The 9522A is configured through the use of AT commands. A full list-

ing of the supported AT commands can be found in the AT Command Reference document. 8 43755_user_guide 2/1/05 5:00 PM Page 12 Iridium Limited Warranty For Satellite Subscriber Radiotelephone Products 1. Coverage and Duration Iridium warrants that its new satellite subscriber radiotelephone products and accessories (the "Product") shall be free from defects in materials and workmanship for a period of twelve (12) months from the date such Product is delivered to the first end user purchaser or first lessee (the "Purchaser"), or the date such Products are first placed into satellite subscriber service, whichever occurs earliest. Iridium, at its option, shall at no charge to Purchaser, either repair or replace the Product, or refund the purchase price of a Product that does not conform to this warranty, provided the Product is returned in accordance with the instructions set out below and within the war-

ranty period. These remedies are Purchaser's exclusive remedies under this warranty. Repair may include the replacement of parts or boards with functionally equivalent reconditioned or new parts or boards. A product that has been repaired or replaced is warranted for the balance of the original warranty period. A Product for which a replacement has been provided shall become Iridium's property. This warranty is made by Iridium to the Purchaser of the Products only, and it is not assignable or transferable by the Purchaser. This is Iridium's sole and complete warranty for the Products. Iridium assumes no obligation or liability for additions or modifications to this warranty unless made in writing and signed by an officer of Iridium. Iridium does not warrant any installation, maintenance, or service of the Products not performed by Iridium. This Product is covered by a U.S.A. warranty. If the Product has been sold outside of the U.S.A., Iridium will honor the U.S.A. warranty terms and conditions only. Outside of the U.S.A., any different war-

ranty terms, liabilities and/or legal requirements of the country in which the Product is sold are specifically disclaimed by Iridium. 2. Conditions Not Covered By This Warranty a. Products that are integrated, installed, maintained, or serviced in any manner other than in accordance with the Iridium user documen-

tation furnished with or applicable to the Product. b. Product damage caused by the use of ancillary equipment not fur-

nished Iridium, including accessories and peripherals. c. Problems where the Product is used in a combination with ancil-

lary equipment not furnished by Iridium, and it is determined by Iridium there is no fault with the Product. d. Ancillary equipment not furnished by Iridium which is attached to or used in connection with the Products is not the responsibility of Iridium, and all such equipment is expressly excluded from this war-

ranty. Furthermore, Iridium does not warrant the integrated operation of the combination of the Products with any ancillary equipment not furnished by Iridium. e. Defects or damage resulting from: use of the Product in any man-

ner not normal or customary; misuse, accident or neglect including but not limited to dropping the Product onto hard surfaces, immer-

sion in or exposure to water, rain or extreme humidity, immersion in or exposure to sand, dirt or other particulates, exposure to extreme heat, spills of food or liquid; improper testing, operation, mainte-

nance, installation, adjustment; or any alteration or modification of any kind. f. Batteries manufactured by Iridium and sold with Products whose capacity exceeds 80% of rated capacity are not covered. Batteries whose capacity falls below 80% of rated capacity, or that develop leakage, shall be considered nonconforming. This warranty is void-

9 43755_user_guide 2/1/05 5:00 PM Page 13 ed for batteries if: a) such batteries are charged by other than the Iridium-approved battery charger specified for charging such batter-

ies; b) any seals on such batteries are broken or show evidence of tampering; or c) such batteries are used in equipment other than the Product for which they are specified; or d) such batteries are charged and stored at temperatures greater than 60 degrees centi-

grade. g. Breakage or damage to antennas, or scratches or other damage to plastic surfaces or other externally exposed parts caused by Purchaser's use. h. Products disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection and testing to verify any warranty claim. i. Products on which serial numbers or date tags have been removed, altered or obliterated. j. Coil cords that are stretched or on which the modular tab is bro-

ken; leather cases, which are covered under separate manufactur-

ers' warranties;

k. Products rented on a month-to-month basis. l. Normal wear and tear. 3. Obtaining Warranty Service For warranty questions, repairs, or for the return of Product, please call your Service Provider or Point-of-Sale, not Iridium. Equipment needing service should be returned to your Service Provider or Point-of-Sale, not Iridium. SERVICE WORK PERFORMED BY SERVICE CENTERS NOT AUTHO-

RIZED BY IRIDIUM TO PERFORM SUCH WORK WILL VOID THIS WARRANTY. All Products shipped to Iridium's authorized Warranty Service Center must be shipped with freight and insurance prepaid. Purchaser must include with the Product a bill of sale, a lease, or some other compa-

rable proof of purchase, the name and location of the installation facility, if any, and most importantly, the Purchaser's name, address, and telephone number and a written description of the problem. Product that is repaired or replaced under this warranty shall be returned to Purchaser at Iridium's expense for the freight and insur-

ance, and at Purchaser's expense for any applicable duties or other charges. If additional information is needed, please contact Iridium at the address and phone number listed in Paragraph 7 below. 4. General Provisions THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FURTHER, THIS WARRANTY COVERS THE PRODUCTS ONLY, AND NO WARRANTY IS MADE AS TO COV-

ERAGE, AVAILABILITY, OR GRADE OF SERVICE PROVIDED BY IRID-

IUM SEPARATELY FOR IRIDIUM SATELLITE SERVICES. IN NO EVENT SHALL IRIDIUM BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT IN QUESTION, OR FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMER-

CIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. 5. Conditions of Use and Disclaimer of Liability Users of the Iridium Satellite LLC ("Iridium") mobile satellite phone service and related equipment, including without limitation those using the phone service and equipment in any manner in conjunction 10 43755_user_guide 2/1/05 5:00 PM Page 14 with emergency 911or emergency 112 or any other distress calling or emergency services, both public of privately operated, acknowledge and agree as a condition of the provision of phone service and equipment by Iridium that they will make no claim, whether in con-

tract, tort or otherwise, against Iridium for bodily injury, loss of life, damage to property or for any other loss whatsoever, or for special, incidental, indirect, consequential or punitive damages, by reason of any unavailability, delay, faultiness or failures of the Iridium facilities or phone service or equipment or for inaccuracies or failures with regard to any user information provided. This is a waiver and release and disclaimer of liability to the fullest extent permitted by applica-

ble law and applies regardless of the cause of any liability, including without limitations, to wrongful conduct, omission or fault of employ-

ees or agents of Iridium. Iridium makes no warranties, express or implied, including any implied warranty of merchantability or fitness for a particular pur-

pose concerning Iridium service or equipment. Iridium cannot prom-

ise uninterrupted or error free service. The Iridium service does not currently interact with E911 or E112 or other public emergency services. Such calls are not able to be made on the Iridium system. Users by their use of the phone service and equipment consent to Iridium's disclosure of user information, including but not limited to name, address, telephone number and location information, includ-

ing the geographic coordinates of equipment, to governmental and quasi-governmental agencies such as emergency service providers and law enforcement agencies, where Iridium deems it necessary in its sole discretion to respond to an exigent circumstances. These governmental and quasi-governmental agencies shall be deemed

"users" for all purposes of this Disclaimer of Liability. 6. State Law and Other Jurisdiction Rights;

Software Copyrights SOME STATES AND OTHER JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATION ON HOW LONG AN IMPLIED WARRAN-

TY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER. This warranty gives Purchaser specific legal rights, and Purchaser may also have other rights which vary from jurisdiction to jurisdic-

tion. Laws in the United States and other countries preserve for Iridium certain exclusive rights for copyrighted Product software such as the exclusive rights to reproduce in copies and distribute copies of such Product software. Product software may be copied into, used in and redistributed with only the Product associated with such Product software. No other use, including without limitation disassembly, of such Product software or exercise of exclusive rights in such Product software is permitted. 7. Contact For additional information about this Product warranty, please con-

tact your Service Provider or Point of Sale. For additional information about Iridium products and services, please contact Iridium as follows:

By Telephone: Customer ServiceToll Free Number: +1-866-947-4348 Local or International Number: +1-480-752-5155 By Email:

By Mail:

Info@iridium.com Iridium Satellite LLC Attn: Customer Service 8440 S. River Parkway, Tempe, AZ 85284 USA 11 43755_user_guide 2/1/05 5:00 PM Page 15 E C Directive Declaration of Conformity This is to certify that the following equipment complies with all rele-

vant Essential Health and Safety Requirements of the Radio and Telecommunications Terminal Equipment Directive 1999/5/EC and the Low Voltage Directive 73/23/EC as amended by 93/68/EC. Equipment description Iridium 9522A Satellite L-band transceiver Manufacturer Iridium Satellite, LLC 8440 South River Parkway, Tempe, AZ 85284 USA The following harmonised standards have been applied to the design of the L-band transceiver:

Standard EN 60950-1:2001 Description Information technology equipment - Safety - Part 1:

General requirements EN 301 489-20V1.2.1 (2002 11) EN 301 489-01V1.4.1 (2002-08) ETSI EN 50360:2001 Electromagnetic compatibility and Radio Spectrum Matters

(ERM);ElectroMagnetic Compatibility (EMC) standard for radio equipment and services. Product standard to demonstrate the compliance of mobile phones with the basic restrictions related to human exposure to electromagnetic fields (300MHz to 3GHz) ETSI EN 301 441 V1.1.1 05/2000 Satellite Earth Stations and Systems (SES); Harmonised EN for Mobile Earth Stations MESs) A technical file is retained by Iridium Satellite LLC. Related test reports are available upon request directly from Iridium Satellite LLC. The 9522A L-band transceiver is declared conformant only if it is used in the configuration tested and if the L-band transceiver is used as described in the 9522A User Guide. Signed _____________________________ CTO, Iridium Satellite, LLC Date __________________________ 12 43755_user_guide 2/1/05 5:00 PM Page 16 Iridium Satellite LLC Headquarters 6701 Democracy Blvd., Suite 500 Bethesda, MD 20817 USA Phone +1.301.571.6200 Fax +1.301.571.6250 Iridium Satellite LLC 8440 S. River Parkway Tempe, AZ 85284 Toll Free +1.866.947.4348 Local or International +1.480.752.5155 Fax +1.480.752.1105 email info@iridium.com www.iridium.com LUG0501