FCC ID: VGX6012A Vehicle Mounted Terminal Class B Device 12-60 Nominal VDC Isolated with NFC Transmitter

JLT6012A Quick Start Guide JLT6012A JLT Mobile Computers AB Head Office: Isbjrnsvgen 3, SE-352 45 Vxj, SWEDEN Sales Office: Medborgarplatsen 3, Plan 8, SE-118 26 Stockholm, SWEDEN Phone: +46 470 53 03 00 Fax+46 470 445 29 Email: info@jltmobile.com North America: 7402 West Detroit Street, Suite 150 Chandler, Arizona 85284, USA Phone +1 480 705 4200 Toll free US: 844-705-4200 First start Android operating system is preinstalled on the unit. Follow instructions and steps given to complete the user setup. See section Maintenance for SIM-card installation. Touch Screen JLT6012A is equipped with a Projected Capacitive Touch screen. Also called PCT or PCAP. The touch screen is calibrated from factory and needs no further calibration. It has a resistant glass surface that can be cleaned with a damp cloth, ordinary soap or hand-dish washing fluids. Purpose made cleaning fluids may also be used. Its normally operated with fingers, and may also be used with purpose designed stylus for PCT or PCAP. A stylus designed for resistive touch screens will not work. NOTE: As the surface is made of glass it will withstand most common substances, but Do NOT use fluids like bleach or any strong alkali cleaning agents such as sodium or potassium hydroxide for cleaning as it may etch the glass and leave grey marks. FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. WWAN Main, SMA GNSS, SMA WWAN Aux, SMA USB2 x2, USB type A Ethernet, RJ45 USB3.1, OTG, ADB, Display, USB type C USB3.1, USB type A RS232C, configurable 5V supply on pin1/9, D-Sub-9 Isolated Power input, 9-72VDC, nominal input voltage 12-60VDC Pin 1 = Positive Pin 2 = Remote On/Off Pin 3 = Power Ground Interfaces Connectors From left to right:

Power cable Connect cable as shown in the picture below. Remote may be connected to a remote switch or a vehicle ignition key for automatic On/Off control where high is on and low is off. Important:

If not used for remote operation remote input pin must be connected to positive input to enable operation. JLT standard cable configuration: Red = Positive, White = Remote, Black =

Ground The power cable must be dimensioned to handle up to 40 Watts, or use cable supplied by JLT. Recommended cable area 0.75 mm2, AWG 18 or larger. Important: Do NOT apply any solder to the cable ends. It will eventually make the connection unreliable and loose during use. Power Input and UPS The unit is equipped with an isolated wide range 9-72VDC input. Nominal input voltage 12-60VDC. If power is lost or switched off, the unit will switch to the UPS-battery to perform a controlled system shutdown. Battery and remote operation are configurable in JLT Control Panel application. Remote input is recommended to utilize to automatically power on and off the unit. Typically connects to a vehicle ignition switch. No additional grounding of unit is normally required. Power consumption:

Stand by: 0.5W Idle, active screen: typical 15W Maximum: 40W Power On/Off button, Press and hold 2 seconds for shut down menu, 8 seconds for forced Buttons From left to right:

shutdown. Brightness Brightness +

Android buttons, Home, Back and Menu Mounting Cable Strain Relief and Rubber Sealing Plugs Use included cable ties to attach cables to the strain relief plate. Install rubber sealing plugs to unused ports. JLT provided Mounting Kits: RAM RAM Mount -> Computer: Use included screws and washers. Usage of thread locking products like Loctite is recommended. Mounting with other brands and parts When mounting a JLT unit to a VESA bracket, use M6 screws with correct length. The inserting part of the screw should be minimum 5mm and must NOT exceed 8.5mm. (That is 8 complete turns on the screw). If screws are too long, build up with washers to adjust the inserting part of screw. If this is not done and the screws are too long, they will deform the aluminum case inwardly when applying great force. Torque: Maximum 6Nm Important:

The vehicle computer and bracket must be firmly secured to a surface that can support the vehicle computers weight and include optional accessories such as keyboard and scanners. Computer weight = 2.9 kg or 6.4 lb Keyboard mount An accessory keyboard mount is available from JLT that mounts towards the two M6 screw holes on each side. Fasteners are included with the mount. If other fasteners or screws are being used the depth of mounting holes are maximum 8mm. The keyboard mount has multiple mounting hole alternatives and comes with a Velcro adhesive tape to adapt to any keyboard. Its adjustable to allow different keyboards and height. Mounting screws come with the selected keyboard, if supplied from JLT Mobile. Wireless Communication WLAN: 802.11 ac/a/b/g/n 2x2 Dual Band MU-MIMO Dual Mode Bluetooth 2x Integrated Antennas 2.4Ghz / 5Ghz NFC Optional:

WWAN: 4G/3G, HSPA+, UMTS, LTE GNSS: GPS, Glonass, Galileo, BeiDou See section Maintenance-Service lid overview for SIM-card insertion. For best performance, make sure no antennas are obstructed, especially by conductive material such as any metal. The NFC are for close range >10mm, make sure its physically accessible when mounting unit. Maintenance Battery Replacement Unscrew the six Torx 10 screws. Mount battery in reverse order make sure battery and gasket are in correct position. Lift the lid and gasket. Lift the battery and unplug cable. Service lid, overview LED indicators and Ambient light sensor LED, 1 1. Green, slow blink every 10 sec. Power is connected, unit is turned OFF 2. Green, Constantly lit Power is connected, unit is in normal operation 3. Orange, Constantly lit Unit is running on battery, preparing shutdown 4. Orange/Green alternately A button is pressed LED, 2 1. Off WiFi, no connection 2. Orange WiFi is connected, WiFi level 1-3 3. Green WiFi is connected, WiFi level 4-5 Ambient light sensor, 3 The ambient light sensor is for automatic brightness adjustment depending on condition of surrounding light

Label and location Thermal Transfer Polyester Label by 3M with thermal inc 1. Adhesive for Powder Coating jltmobile.com Location Label when the optional cellular module is included Reliable performance. Less hassle.

Request for Confidentiality Date: February 12, 2021 Subject: Confidentiality Request for: ______VGX6012A______ Pursuant to FCC 47 CFR 0.457(d) and 0.459, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent *1 Permanent Permanent Permanent Permanent Permanent *3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual JLT Mobile Computers has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: Not applicable The applicant do not requests short term confidential Sincerely, By:

_______________________R&D Manager

(Signature/Title2) Anders Grandin 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Cover letter Date: June 14, 2021 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Supplier's Declaration of Conformity 47 CFR 2.1077 Compliance Information for FCC 15 B Unique Identifier: JLT6012A Responsible Party: JLT Mobile Computers Inc. 7402 West Detroit Street, Suite 150 Chandler, AZ 85226, US Contact: Eric Miller CEO 480-397-1214 (f) FCC Compliance Statement This device complies with Part 15B of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. JLT have had spot checks to cover the various co-located TX configurations:

and those copies of any spot checks are available upon request. Thank you, By:

(Signature) Title:

On behalf of:

Telephone:

JLT Mobile Computers_______

+46 733 743 336_____________ __________________________ R&D Manager______________ Anders Grandin__________